Contents

Hikvision DS-8108LHFHI-K2 System Quick Start Guide PDF

Pages 28
Year 2020
Language(s)
English en
1 of 28
1 of 28

Summary of Content for Hikvision DS-8108LHFHI-K2 System Quick Start Guide PDF

Education Sharing System

Quick Start Guide

Education Sharing System

1

TABLE OF CONTENTS Chapter1 Panels Description ................................................................................................. 7

1.1 Front Panel ................................................................................................................... 7

1.2 Rear Panel .................................................................................................................... 8

Chapter 2 Installation and Connection .................................................................................. 9

2.1 Device Installation ........................................................................................................ 9

2.2 Hard Disk Installation ................................................................................................... 9

2.3 Hard Disk Storage Calculation Chart .......................................................................... 11

Chapter 3 Startup and Shutdown........................................................................................ 12

3.1 Startup ....................................................................................................................... 12

3.2 Shutdown ................................................................................................................... 12

Chapter 4 Basic Configuration............................................................................................. 13

4.1 Network Connection .................................................................................................. 13

4.2 Access via Web Browser ............................................................................................. 14

4.3 Indoor Speed Dome Connection ................................................................................ 15

4.3.1 Connect via Analog Connectors ...................................................................... 15

4.3.2 Connect via Network ....................................................................................... 16

4.4 Automatic Live View Control ...................................................................................... 16

4.4.1 Configure Live View Control View ................................................................... 17

4.4.2 Configure Live View Control Strategy .............................................................. 18

4.4.3 Configure One-touch Configuration ................................................................ 19

4.5 Live View .................................................................................................................... 19

4.6 Schedule Settings ....................................................................................................... 22

4.7 Publish Courseware .................................................................................................... 23

4.8 Playback ..................................................................................................................... 24

4.9 Download Courses ..................................................................................................... 25

Education Sharing System

2

Legal Information 2020 Hangzhou Hikvision Digital Technology Co., Ltd. All rights reserved.

About this Manual

The Manual includes instructions for using and managing the Product. Pictures, charts, images and all other

information hereinafter are for description and explanation only. The information contained in the Manual

is subject to change, without notice, due to firmware updates or other reasons. Please find the latest

version of this Manual at the Hikvision website (https://www.hikvision.com/).

Please use this Manual with the guidance and assistance of professionals trained in supporting the Product.

Trademarks

and other Hikvision's trademarks and logos are the properties of Hikvision

in various jurisdictions.

Other trademarks and logos mentioned are the properties of their respective owners.

: The terms HDMI and HDMI High-Definition Multimedia Interface, and the HDMI Logo

are trademarks or registered trademarks of HDMI Licensing Administrator, Inc. in the United States and

other countries.

Disclaimer

TO THE MAXIMUM EXTENT PERMITTED BY APPLICABLE LAW, THIS MANUAL AND THE PRODUCT DESCRIBED,

WITH ITS HARDWARE, SOFTWARE AND FIRMWARE, ARE PROVIDED AS IS AND WITH ALL FAULTS AND

ERRORS. HIKVISION MAKES NO WARRANTIES, EXPRESS OR IMPLIED, INCLUDING WITHOUT LIMITATION,

MERCHANTABILITY, SATISFACTORY QUALITY, OR FITNESS FOR A PARTICULAR PURPOSE. THE USE OF THE

PRODUCT BY YOU IS AT YOUR OWN RISK. IN NO EVENT WILL HIKVISION BE LIABLE TO YOU FOR ANY SPECIAL,

CONSEQUENTIAL, INCIDENTAL, OR INDIRECT DAMAGES, INCLUDING, AMONG OTHERS, DAMAGES FOR LOSS OF

BUSINESS PROFITS, BUSINESS INTERRUPTION, OR LOSS OF DATA, CORRUPTION OF SYSTEMS, OR LOSS OF

DOCUMENTATION, WHETHER BASED ON BREACH OF CONTRACT, TORT (INCLUDING NEGLIGENCE), PRODUCT

LIABILITY, OR OTHERWISE, IN CONNECTION WITH THE USE OF THE PRODUCT, EVEN IF HIKVISION HAS BEEN

ADVISED OF THE POSSIBILITY OF SUCH DAMAGES OR LOSS.

YOU ACKNOWLEDGE THAT THE NATURE OF THE INTERNET PROVIDES FOR INHERENT SECURITY RISKS, AND

HIKVISION SHALL NOT TAKE ANY RESPONSIBILITIES FOR ABNORMAL OPERATION, PRIVACY LEAKAGE OR OTHER

DAMAGES RESULTING FROM CYBER-ATTACK, HACKER ATTACK, VIRUS INFECTION, OR OTHER INTERNET

SECURITY RISKS; HOWEVER, HIKVISION WILL PROVIDE TIMELY TECHNICAL SUPPORT IF REQUIRED.

YOU AGREE TO USE THIS PRODUCT IN COMPLIANCE WITH ALL APPLICABLE LAWS, AND YOU ARE SOLELY

RESPONSIBLE FOR ENSURING THAT YOUR USE CONFORMS TO THE APPLICABLE LAW. ESPECIALLY, YOU ARE

RESPONSIBLE, FOR USING THIS PRODUCT IN A MANNER THAT DOES NOT INFRINGE ON THE RIGHTS OF THIRD

PARTIES, INCLUDING WITHOUT LIMITATION, RIGHTS OF PUBLICITY, INTELLECTUAL PROPERTY RIGHTS, OR DATA

PROTECTION AND OTHER PRIVACY RIGHTS. YOU SHALL NOT USE THIS PRODUCT FOR ANY PROHIBITED END-USES,

INCLUDING THE DEVELOPMENT OR PRODUCTION OF WEAPONS OF MASS DESTRUCTION, THE DEVELOPMENT OR

PRODUCTION OF CHEMICAL OR BIOLOGICAL WEAPONS, ANY ACTIVITIES IN THE CONTEXT RELATED TO ANY

NUCLEAR EXPLOSIVE OR UNSAFE NUCLEAR FUEL-CYCLE, OR IN SUPPORT OF HUMAN RIGHTS ABUSES.

IN THE EVENT OF ANY CONFLICTS BETWEEN THIS MANUAL AND THE APPLICABLE LAW, THE LATER PREVAILS.

Education Sharing System

3

Regulatory Information

FCC Information

Please take attention that changes or modification not expressly approved by the party

responsible for compliance could void the users authority to operate the equipment.

FCC compliance: This equipment has been tested and found to comply with the limits for a Class A

digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide

reasonable protection against harmful interference when the equipment is operated in a

commercial environment. This equipment generates, uses, and can radiate radio frequency energy

and, if not installed and used in accordance with the instruction manual, may cause harmful

interference to radio communications. Operation of this equipment in a residential area is likely to

cause harmful interference in which case the user will be required to correct the interference at

his own expense.

FCC Conditions

This device complies with part 15 of the FCC Rules. Operation is subject to the following two

conditions:

1. This device may not cause harmful interference.

2. This device must accept any interference received, including interference that may cause

undesired operation.

EU Conformity Statement

This product and - if applicable - the supplied accessories too are marked with "CE" and

comply therefore with the applicable harmonized European standards listed under the

EMC Directive 2014/30/EU, the LVD Directive 2014/35/EU, the RoHS Directive 2011/65/EU.

2012/19/EU (WEEE directive): Products marked with this symbol cannot be disposed of

as unsorted municipal waste in the European Union. For proper recycling, return this

product to your local supplier upon the purchase of equivalent new equipment, or

dispose of it at designated collection points. For more information see: www.recyclethis.info

2006/66/EC (battery directive): This product contains a battery that cannot be disposed

of as unsorted municipal waste in the European Union. See the product documentation

for specific battery information. The battery is marked with this symbol, which may

include lettering to indicate cadmium (Cd), lead (Pb), or mercury (Hg). For proper recycling, return

the battery to your supplier or to a designated collection point. For more information see:

www.recyclethis.info

Industry Canada ICES-003 Compliance

This device meets the CAN ICES-3 (A)/NMB-3(A) standards requirements.

Education Sharing System

4

Applicable Models

This manual is applicable to the models listed in the following table.

Symbol Conventions

The symbols that may be found in this document are defined as follows.

Product Name Model

Education Sharing System DS-8108LHFHI-K2

Symbol Description

Provides additional information to emphasize or supplement important points of the main text.

Indicates a potentially hazardous situation, which if not avoided, could result in equipment damage, data loss, performance degradation, or unexpected results.

Indicates a hazard with a high level of risk, which if not avoided, will result in death or serious injury.

Education Sharing System

5

Safety Instructions

Proper configuration of all passwords and other security settings is the responsibility of the installer and/or end-user.

Firmly connect the plug to the power socket. Do not connect several devices to one power adapter. Power off the device before connecting and disconnecting accessories and peripherals.

Shock hazard! Disconnect all power sources before maintenance.

The equipment must be connected to an earthed mains socket-outlet.

The socket-outlet shall be installed near the equipment and shall be easily accessible.

indicates hazardous live and the external wiring connected to the terminals requires installation by an instructed person.

Never place the equipment in an unstable location. The equipment may fall, causing serious personal injury or death.

Input voltage should meet the SELV (Safety Extra Low Voltage) and the LPS (Limited Power Source) according to the IEC60950-1.

High touch current! Connect to earth before connecting to the power supply.

If smoke, odor or noise rise from the device, turn off the power at once and unplug the power cable, and then please contact the service center.

Use the device in conjunction with an UPS, and use factory recommended HDD if possible.

This product contains a coin/button cell battery. If the battery is swallowed, it can cause severe internal burns in just 2 hours and can lead to death.

This equipment is not suitable for use in locations where children are likely to be present.

CAUTION: Risk of explosion if the battery is replaced by an incorrect type.

Improper replacement of the battery with an incorrect type may defeat a safeguard (for example, in the case of some lithium battery types).

Do not dispose of the battery into fire or a hot oven, or mechanically crush or cut the battery, which may result in an explosion.

Do not leave the battery in an extremely high temperature surrounding environment, which may result in an explosion or the leakage of flammable liquid or gas.

Do not subject the battery to extremely low air pressure, which may result in an explosion or the leakage of flammable liquid or gas.

Dispose of used batteries according to the instructions

Keep body parts away from fan blades and motors. Disconnect the power source during servicing.

Preventive and Cautionary Tips

Before connecting and operating your device, please be advised of the following tips:

Education Sharing System

6

The device is designed for indoor use only. Install it in a well-ventilated, dust-free environment without liquids.

Ensure recorder is properly secured to a rack or shelf. Major shocks or jolts to the recorder as a result of dropping it may cause damage to the sensitive electronics within the recorder.

The equipment shall not be exposed to dripping or splashing and that no objects filled with liquids shall be placed on the equipment, such as vases.

No naked flame sources, such as lighted candles, should be placed on the equipment.

The ventilation should not be impeded by covering the ventilation openings with items, such as newspapers, table-cloths, curtains, etc. The openings shall never be blocked by placing the equipment on a bed, sofa, rug or other similar surface.

For certain models, ensure correct wiring of the terminals for connection to an AC mains supply.

For certain models, the equipment has been designed, when required, modified for connection to an IT power distribution system.

Use only power supplies listed in the user manual or user instruction.

Education Sharing System

7

Chapter1 Panels Description

1.1 Front Panel

Figure 1-1 Front Panel

Table 1-1 Panel Description

No. Name Description

1 Status Indicators

Recording Green: recording Unlit: not recording

Direct Solid green: live view control normal Solid red: automatic live view control is

enabled

Publish/Download Blinking red: downloading and publishing the courseware

Solid red: downloading and publishing the courseware failed

Unlit: downloading and publishing the courseware succeeded. Or no downloading or publishing tasks

HDD Blinking red: reading or writing hard disk normally

Network Blinking green: network communication normal

2 OLED Screen Display IP address and hard disk storage status. You can press the power button to activate the screen display.

3 USB USB interface

4 Power On/Off Press the button for at least 6 seconds to turn on/off the device.

Education Sharing System

8

1.2 Rear Panel

Figure 1-2 Rear Panel

Table 1-2 Panel Description

No. Name Description

1 ANT Antenna interface

2 SDI IN Video inputs of SDI connector

3 VIDEO IN 1 Video inputs of VGA and HDMI interface

4 LOOP OUT VGA and HDMI loopback interface

5 VIDEO IN 2 Video inputs of VGA and HDMI interface

6 VIDEO OUT Video outputs of VGA and HDMI interface

7 LAN1/LAN2 Network interfaces

8 USB 3.0 USB 3.0 interfaces

9 AUDIO IN Audio input, 3.5 mm connector

10 AUDIO OUT Audio output, 3.5 mm connector

11 AUDIO IN Audio input, RCA connector

12 AUDIO OUT Audio output, RCA connector

13 AUDIO OUT Single track of green connector

14 RS-485 RS-485 connector

15 AUDIO IN Audio input

16 IN-ALARM-OUT Alarm input/output connector

17 12 VDC Power supply

18 POWER Power switch

19 GND Ground

Education Sharing System

9

Chapter 2 Installation and Connection

2.1 Device Installation

During device installation:

Keep all liquids away from the device.

Use brackets for rack mounting.

Ensure ample room for audio and video cables.

When routing cables, ensure that the bend radius of the cables are no less than five times than its diameter.

Ensure the alarm and RS-485 cables are well connected.

Allow at least 2cm (0.75-inch) of space between racks mounted devices.

Ensure the device is grounded.

Environmental temperature should be within the range of -10 to +55 C, +14 to +131 F.

Environmental humidity should be within the range of 10% to 90%.

Before cleaning the device, cut off electricity and plug out the power cable.

To protect the device from short circuit caused by the damp dust in circuit board, clean the circuit, cables, chassis, and fans with a soft brush.

Use the neutral detergent diluted with water to remove the dirt. Instead of the strong detergent and volatile solvent, like alcohol, benzene, and diluent, or the surface coating will be damaged.

A factory recommended hard disk should be used for this device.

2.2 Hard Disk Installation

Before you start:

Cut off the power supply for the device before installing a hard disk. A factory recommended hard disk should be used for this installation.

Tools Required: Screwdriver.

Purpose:

Follow the steps to install hard disk.

Step 1 Remove the cover from the device by unfastening the screws on the rear and side panel.

Education Sharing System

10

Figure 2-1 Unfasten Screws

Step 2 Connect the data cable and hard disk power cable.

1) Connect the data cable with the device motherboard data port.

2) Connect the data cable with the hard disk data port.

3) Connect the hard disk power cable with the hard disk power port.

4) Connect the hard disk power cable with the device motherboard power supply port.

Figure 2-2 Connect Hard Disk and Motherboard

Step 3 Fix the hard disk on the bottom panel by fastening the screws between the bottom panel and hard disk.

Figure 2-3 Fix Hard Disk

Step 4 Reinstall the cover and fasten the screws on the rear and side panel.

Education Sharing System

11

2.3 Hard Disk Storage Calculation Chart

The following chart shows an estimation of storage space used based on recording at one channel for an hour at a fixed bit rate.

Bit Rate Storage Used

96K 42M

128K 56M

160K 70M

192K 84M

224K 98M

256K 112M

320K 140M

384K 168M

448K 196M

512K 225M

640K 281M

768K 337M

896K 393M

1024K 450M

1280K 562M

1536K 675M

1792K 787M

2048K 900M

4096K 1.8G

8192K 3.6G

16384K 7.2G

Please note that supplied values for storage space used is just for reference. The storage values in

the chart are estimated by formulas and may have some deviation from actual value.

Education Sharing System

12

Chapter 3 Startup and Shutdown

Purpose:

Proper startup and shutdown procedures are crucial to expanding the life of the device. Follow the steps to start and shut down your device.

3.1 Startup

Step 1 Connect the device and a socket with the provided power cord. It is HIGHLY recommended to use an Uninterruptible Power Supply (UPS) in conjunction with the device.

Step 2 Turn on the switch on rear panel.

3.2 Shutdown

Hold the power button at the front panel for 6 seconds to shut down the device.

Education Sharing System

13

Chapter 4 Basic Configuration

4.1 Network Connection

You shall acknowledge that the use of the product with Internet access might be under network security risks. For avoidance of any network attacks and information leakage, please strengthen your own protection. If the product does not work properly, please contact with your dealer or the nearest service center.

To ensure the network security of the education sharing system, we recommend you to have the device assessed and maintained termly. You can contact us if you need such service.

Purpose:

Create network connection between the education sharing system and your computer. Two methods are provided, including connecting the education sharing system via a LAN (Local Area Network) and via a WAN (Wide Area Network). We take the example of connecting via LAN to describe the steps.

Before you start:

Power on the device and install the SADP software in your computer.

Step 1 Create the network connection between the device and your computer.

Option1: Directly connect the device to the computer with a network cable.

Option 2: Connect the device and your computer via a switch or a router.

Figure 4-1 Connect Directly

Education Sharing System

14

Figure 4-2 Connect via a Switch or a Router

4.2 Access via Web Browser

Purpose:

You can get access to the device via web browser. You may use one of the following listed web browsers: Internet Explorer 6.0, Internet Explorer 7.0, Internet Explorer 8.0, Internet Explorer 9.0, Internet Explorer 10.0, Apple Safari, Mozilla Firefox, and Google Chrome. The supported resolutions include 1024*768 and above.

Before you start:

Obtain the device IP address via SADP software. Refer to the user manual for the detailed steps of obtain online device and modify device network parameters via SADP software.

Step 1 Open web browser, enter the IP address of the device and then press Enter.

Step 2 Log in the device.

If the device has not been activated, you need to activate the device first before login.

Figure 4-3 Set Admin Password

1) Enter the same password in Password and Confirm.

2) Click OK to activate and log in the device.

Education Sharing System

15

STRONG PASSWORD RECOMMENDEDWe highly recommend you create a strong password of your own choosing (Using a minimum of 8 characters, including at least three of the following categories: upper case letters, lower case letters, numbers, and special characters.) in order to increase the security of your product. And we recommend you reset your password regularly, especially in the high security system, resetting the password monthly or weekly can better protect your product.

If the device is already activated, enter the user name and password in the login interface, and click Login.

Figure 4-4 Login

Step 3 Install the plug-in before viewing the live video and managing the device. Follow the installation prompts to install the plug-in.

If you enter the wrong password 7 times when login, the current user will be locked for 30

minutes.

You may have to close the web browser to finish the installation of the plug-in.

4.3 Indoor Speed Dome Connection

Purpose:

Before you can get the live view or record the image of classroom, connect the education specified speed dome to the device via analog connector or network.

4.3.1 Connect via Analog Connectors

Connect the education specified speed dome and device video input connector with BNC (Bayonet Nut Connector).

Education Sharing System

16

4.3.2 Connect via Network

Before you start:

Connect the education specified speed dome to network.

Step 1 Go to Configuration Recording Settings Live View Settings Live View Channel Settings.

Figure 4-5 Live View Channel Settings

Step 2 Click Add to add IP camera.

Step 3 Enter the IP camera parameters.

Camera type cannot be duplicated with each other.

Figure 4-6 Add IP Camera

Step 4 Click OK.

4.4 Automatic Live View Control

Purpose:

Education Sharing System

17

Combining with the same brand education specified speed dome, the education sharing system can automatically display the teacher image, student image, or HDMI/VGA multimedia image in live view control channel according to the speed dome smart detection information. Besides, the speed dome can precisely position and track teacher, and record the teaching process.

Connect same brand education specified speed dome and education sharing system via

network. For detailed steps, refer to 4.3.2 Connect via Network.

In automatic live view control mode, when a smart event occurs to the education specified

speed dome or HDMI/VGA multimedia courseware changes, the education sharing system

will automatically display the teacher image, student image, or HDMI/VGA multimedia

image in the main screen according to the priority.

You need to log in to education specified speed dome configuration interface to configure

its smart detection rules.

4.4.1 Configure Live View Control View

Step 1 Go to Configuration > Recording Settings > Live View Settings > View Settings.

Figure 4-7 Live View Control View

Step 2 Select View Mode.

Movie: You need to set Assistance Mode for movie mode. When one alarm is triggered, it will display in single screen. But if two or more alarms are trigged, it will display as what the Assistance Mode is set, including Single Screen, Dual-Screen, and Picture-in-Picture.

PIP: PIP (Picture-in-picture) is the video display method that when the video is on full screen, another video is displayed in the inset window at the same time.

Education Sharing System

18

Multi-Screen: Multi-image of the camera are displayed simultaneously on the screen.

Step 3 Select display channel.

Step 4 Click Save.

4.4.2 Configure Live View Control Strategy

Step 1 Go to Configuration > Recording Settings > Live View Settings > Live View Control Settings.

Figure 4-8 Live View Control Strategy

Step 2 Select a channel for modification.

Step 3 Click Modify.

Figure 4-9 Strategy Configuration Interface

Step 4 Set the parameters, including priority, IP address, port, user name, password, etc.

Education Sharing System

19

Priority: The priority of the selected channel. The larger the value is, the higher the priority will be.

Channel Display Time (s): The display time of multimedia is recommended to set as its actual duration. Other channels display time is recommended to set as 0. Valid channel display time range: [0, 900].

Step 5 Click OK to save the settings.

4.4.3 Configure One-touch Configuration

Step 1 Go to Configuration > Recording Settings > Live View Settings > Live View Strategy Settings.

Step 2 Click Add.

Step 3 Enter the channel parameters of live view control strategy.

Step 4 Click OK.

Step 5 Click One-touch Configuration.

The device will automatically recognize supportable education specified cameras. If issues occur,

contact the product distributor for help.

4.5 Live View

Purpose:

You can view the live image of connected cameras with manual semi-auto or auto mode, and record the course video.

Before you start:

Ensure the device has successfully connected to the education specified cameras, and your web browser has installed the latest web component.

Step 1 Go to Live View by web browser.

Education Sharing System

20

Figure 4-10 Live View

Step 2 Click Set to set the view mode.

Figure 4-11 View Mode

Education Sharing System

21

Table 4-1 View Mode Description

Mode Icon Description

Movie Single screen

Picture-in-Picture PIP 1, overlay the picture at the lower right corner

PIP 1, overlay the picture at the lower left corner

Multi-Screen

Multi-Screen 1, split screen in half

Multi-Screen 2, split screen in three blocks with the larger one at left side

Multi-Screen 3, split screen in three blocks with the larger one at right side

Multi-Screen 4, split screen in four blocks with the larger one at left side

Multi-Screen 5, split screen in four blocks with the larger one at right side

Step 3 Optionally, when you are in single screen, you can double-click the windows at the bottom to switch live view camera.

Step 4 Optionally, click or to start/stop course recording. You shall enter the course informaiton when you start course recording.

1) Enter course information including Course Name, Teacher, and Course Introduction.

2) You can check Video Head or Video Trailer to addvideo head or tailto the recording video. You can edit the head or tail in Configuration > Recording Settings > Video Head/Tail Configuration.

3) Click OK.

Figure 4-12 Course Information

Step 5 Optionally, select the live mode as Manual, SimiAuto, or Auto.

Education Sharing System

22

Manual: Manually dispaly the image to the main screen by double-clicking the camera display window at the bottom. You shall use the PTZ control panel to manually track the object.

SimiAuto: The speed dome can automatically track object, but you still have to manually switch live view image by double-clicking the camera display window at the bottom.

Auto: The speed dome can automatically track object. The device will automatically display image to the main screen when the connected education specified cameras have

detected smart events. The auto live view control is enabled by default. Refer to ! ! for details.

Step 6 Optionally, for the student and teacher channel, click PTZ to rotate the camera to desired view.

Figure 4-13 PTZ Control Panel

4.6 Schedule Settings

Step 1 Go to Configuration > System Settings > Camera Management > Record Schedule.

Step 2 Select Channel No.

Step 3 Check Enable.

Step 4 Select the recording type, including Continuous, Motion, Alarm, Motion | Alarm, Motion & Alarm, and Event.

Step 5 Set the recording schedule of selected day.

Step 6 Optionally, you can click Copy to to copy the schedule settings to other channel(s).

Step 7 Optionally, click Advanced to set the pre-record and post-record time of the recording schedule, and expired time of the recording file.

Step 8 Click Save.

Education Sharing System

23

Figure 4-14 Schedule Settings

4.7 Publish Courseware

Purpose:

The recorded courses can be automatically published to FTP server.

Step 1 Go to Configuration > System Settings > FTP Publishing > Publish Configuration.

Figure 4-15 Publishing Configuration

Step 2 Enter the FTP server address, port, user name, and password.

Step 3 Click Set to select the publishing channel(s).

Step 4 Click OK.

Education Sharing System

24

Figure 4-16 Set Publishing Channel

Step 5 Set Publishing Path.

Step 6 Optionally, check Auto Publishing to automatically publish courses. You can set Date Published as Last Course or Custom time for the course that requires to be published to FTP.

Step 7 Click Save to save the settings

The published course video format is MP4.

4.8 Playback

Purpose:

You can play back videos saved in the device.

Step 1 Go to Playback.

Education Sharing System

25

Figure 4-17 Playback

Step 2 Click Video.

Step 3 Select the channel in the left channel list.

Step 4 Set date and time. The day with mark has record file.

Step 5 Click .

Step 6 You can drag the time bar at the bottom, or click and to adjust playback time.

Step 7 Click to start playback.

4.9 Download Courses

Step 1 Go to Playback.

Education Sharing System

26

Figure 4-18 Playback Interface

Step 2 Click .

Step 3 Set the search conditions.

Step 4 Select the course(s) from the search result for downloading.

Step 5 Click Download to start downloading.

The record file will be downloaded locally. You can set the download path in Configuration >

System Settings > Syst

Manualsnet FAQs

If you want to find out how the DS-8108LHFHI-K2 Hikvision works, you can view and download the Hikvision DS-8108LHFHI-K2 System Quick Start Guide on the Manualsnet website.

Yes, we have the Quick Start Guide for Hikvision DS-8108LHFHI-K2 as well as other Hikvision manuals. All you need to do is to use our search bar and find the user manual that you are looking for.

The Quick Start Guide should include all the details that are needed to use a Hikvision DS-8108LHFHI-K2. Full manuals and user guide PDFs can be downloaded from Manualsnet.com.

The best way to navigate the Hikvision DS-8108LHFHI-K2 System Quick Start Guide is by checking the Table of Contents at the top of the page where available. This allows you to navigate a manual by jumping to the section you are looking for.

This Hikvision DS-8108LHFHI-K2 System Quick Start Guide consists of sections like Table of Contents, to name a few. For easier navigation, use the Table of Contents in the upper left corner.

You can download Hikvision DS-8108LHFHI-K2 System Quick Start Guide free of charge simply by clicking the “download” button in the upper right corner of any manuals page. This feature allows you to download any manual in a couple of seconds and is generally in PDF format. You can also save a manual for later by adding it to your saved documents in the user profile.

To be able to print Hikvision DS-8108LHFHI-K2 System Quick Start Guide, simply download the document to your computer. Once downloaded, open the PDF file and print the Hikvision DS-8108LHFHI-K2 System Quick Start Guide as you would any other document. This can usually be achieved by clicking on “File” and then “Print” from the menu bar.