Contents

Hikvision DS-240 Storage Quick Start Guide PDF

1 of 29
1 of 29

Summary of Content for Hikvision DS-240 Storage Quick Start Guide PDF

DS-AT1000S Series Storage System

Quick Start Guide

DS-AT1000S Series Storage System Quick Start Guide

1

TABLE OF CONTENTS Chapter 1 Working Environment and Installation ........................................................................ 5

1.1 Environment of Equipment Room ............................................................................................ 5

1.1.1 Power Supply System ...................................................................................................... 5

1.1.2 Temperature and Humidity of Equipment Room ............................................................ 5

1.2 Installation and Initial Power-on .............................................................................................. 7

1.3 Notes for Installation ................................................................................................................ 7

Chapter 2 Appearance and Installation ....................................................................................... 8

2.1 Device Appearance................................................................................................................... 8

2.1.1 Chassis Overall View ....................................................................................................... 8

2.1.2 Front Panel ...................................................................................................................... 8

2.1.3 Description of Buttons in Front Panel ............................................................................. 9

2.1.4 Rear Panel ..................................................................................................................... 11

2.2 Install Accessories .................................................................................................................. 13

2.2.1 Installation Requirement ............................................................................................... 13

2.2.2 Install HDD ..................................................................................................................... 14

2.3 Startup .................................................................................................................................... 16

2.4 Shutdown ............................................................................................................................... 17

Chapter 3 Function Configuration ............................................................................................. 18

Chapter 4 Network ................................................................................................................... 19

4.1 Activate Storage System ......................................................................................................... 19

4.2 Configure Network Parameters .............................................................................................. 19

4.2.1 Modify Network Parameters ......................................................................................... 19

4.2.2 Modify IP Address of Bond Network Interface ............................................................. 21

Chapter 5 System Configuration ................................................................................................ 22

5.1 One-Key Configuration ........................................................................................................... 22

5.2 Format Storage Space ............................................................................................................ 23

5.2.1 Activate Hybrid SAN Sub-System .................................................................................. 23

5.2.2 Format Storage Space ................................................................................................... 24

Chapter 6 Basic Configuration ................................................................................................... 25

6.1 Camera Management............................................................................................................. 25

6.2 Configure Recording Schedule ............................................................................................... 26

6.3 Live View ................................................................................................................................ 27

6.4 Playback.................................................................................................................................. 27

DS-AT1000S Series Storage System Quick Start Guide

2

Quick Start Guide

COPYRIGHT 2019 Hangzhou Hikvision Digital Technology Co., Ltd.

ALL RIGHTS RESERVED.

Any and all information, including, among others, wordings, pictures, graphs are the properties of

Hangzhou Hikvision Digital Technology Co., Ltd. or its subsidiaries (hereinafter referred to be

Hikvision). This user manual (hereinafter referred to be the Manual) cannot be reproduced,

changed, translated, or distributed, partially or wholly, by any means, without the prior written

permission of Hikvision. Unless otherwise stipulated, Hikvision does not make any warranties,

guarantees or representations, express or implied, regarding to the Manual.

About this Manual

This Manual is applicable to DS-AT1000S Series Storage System.

The Manual includes instructions for using and managing the product. Pictures, charts, images and

all other information hereinafter are for description and explanation only. The information

contained in the Manual is subject to change, without notice, due to firmware updates or other

reasons. Please find the latest version in the company website

(http://overseas.hikvision.com/en/).

Please use this user manual under the guidance of professionals.

Trademarks Acknowledgement

and other Hikvisions trademarks and logos are the properties of Hikvision in various

jurisdictions. Other trademarks and logos mentioned below are the properties of their respective

owners.

Legal Disclaimer

TO THE MAXIMUM EXTENT PERMITTED BY APPLICABLE LAW, THE PRODUCT DESCRIBED, WITH ITS

HARDWARE, SOFTWARE AND FIRMWARE, IS PROVIDED AS IS, WITH ALL FAULTS AND ERRORS,

AND HIKVISION MAKES NO WARRANTIES, EXPRESS OR IMPLIED, INCLUDING WITHOUT LIMITATION,

MERCHANTABILITY, SATISFACTORY QUALITY, FITNESS FOR A PARTICULAR PURPOSE, AND

NON-INFRINGEMENT OF THIRD PARTY. IN NO EVENT WILL HIKVISION, ITS DIRECTORS, OFFICERS,

EMPLOYEES, OR AGENTS BE LIABLE TO YOU FOR ANY SPECIAL, CONSEQUENTIAL, INCIDENTAL, OR

INDIRECT DAMAGES, INCLUDING, AMONG OTHERS, DAMAGES FOR LOSS OF BUSINESS PROFITS,

BUSINESS INTERRUPTION, OR LOSS OF DATA OR DOCUMENTATION, IN CONNECTION WITH THE

USE OF THIS PRODUCT, EVEN IF HIKVISION HAS BEEN ADVISED OF THE POSSIBILITY OF SUCH

DAMAGES.

REGARDING TO THE PRODUCT WITH INTERNET ACCESS, THE USE OF PRODUCT SHALL BE WHOLLY

AT YOUR OWN RISKS. HIKVISION SHALL NOT TAKE ANY RESPONSIBILITIES FOR ABNORMAL

OPERATION, PRIVACY LEAKAGE OR OTHER DAMAGES RESULTING FROM CYBER ATTACK, HACKER

ATTACK, VIRUS INSPECTION, OR OTHER INTERNET SECURITY RISKS; HOWEVER, HIKVISION WILL

PROVIDE TIMELY TECHNICAL SUPPORT IF REQUIRED.

SURVEILLANCE LAWS VARY BY JURISDICTION. PLEASE CHECK ALL RELEVANT LAWS IN YOUR

JURISDICTION BEFORE USING THIS PRODUCT IN ORDER TO ENSURE THAT YOUR USE CONFORMS

THE APPLICABLE LAW. HIKVISION SHALL NOT BE LIABLE IN THE EVENT THAT THIS PRODUCT IS

USED WITH ILLEGITIMATE PURPOSES.

IN THE EVENT OF ANY CONFLICTS BETWEEN THIS MANUAL AND THE APPLICABLE LAW, THE LATER

PREVAILS.

DS-AT1000S Series Storage System Quick Start Guide

3

Regulatory Information

FCC Information

FCC compliance: This equipment has been tested and found to comply with the limits for a Class A

digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide

reasonable protection against harmful interference when the equipment is operated in a

commercial environment. This equipment generates, uses, and can radiate radio frequency energy

and, if not installed and used in accordance with the instruction manual, may cause harmful

interference to radio communications. Operation of this equipment in a residential area is likely to

cause harmful interference in which case the user will be required to correct the interference at

his own expense.

The device is advised to note that as a seller or a business user (Class A) Devices and intended for

use outside the Home area.

FCC Conditions

This device complies with part 15 of the FCC Rules. Operation is subject to the following two

conditions:

1. This device may not cause harmful interference.

2. This device must accept any interference received, including interference that may cause

undesired operation.

EU Conformity Statement

This product and - if applicable - the supplied accessories too are marked with "CE" and

comply therefore with the applicable harmonized European standards listed under the

EMC Directive 2014/30/EU, the RoHS Directive 2011/65/EU, the LVD Directive 2014/35/EU.

2012/19/EU (WEEE directive): Products marked with this symbol cannot be disposed of

as unsorted municipal waste in the European Union. For proper recycling, return this

product to your local supplier upon the purchase of equivalent new equipment, or

dispose of it at designated collection points. For more information see: www.recyclethis.info

2006/66/EC (battery directive): This product contains a battery that cannot be disposed

of as unsorted municipal waste in the European Union. See the product documentation

for specific battery information. The battery is marked with this symbol, which may

include lettering to indicate cadmium (Cd), lead (Pb), or mercury (Hg). For proper recycling, return

the battery to your supplier or to a designated collection point. For more information see:

www.recyclethis.info

Industry Canada ICES-003 Compliance

This device meets the CAN ICES-3 (A)/NMB-3(A) standards requirements.

DS-AT1000S Series Storage System Quick Start Guide

4

Applicable Models

This manual is applicable to the models listed in the following table.

Series Model

DS-AT1000S series

DS-AT1000S/160

DS-AT1000S/240

DS-AT1000S/300

DS-AT1000S/320

DS-AT1000S/360

DS-AT1000S/440

DS-AT1000S/480

Symbol Conventions

The symbols that may be found in this document are defined as follows.

Symbol Description

Provides additional information to emphasize or supplement important points of the main text.

Indicates a potentially hazardous situation, which if not avoided, could result in equipment damage, data loss, performance degradation, or unexpected results.

Indicates a hazard with a high level of risk, which if not avoided, will result in death or serious injury.

DS-AT1000S Series Storage System Quick Start Guide

5

Chapter 1 Working Environment and Installation

Devices described in this manual should be installed in the standard equipment room.

1.1 Environment of Equipment Room

1.1.1 Power Supply System

The storage system is sensitive to the change of a voltage, and an excessively high or low voltage, or a sudden change of the voltage may delete the data in the memory or even cause the damage of the components. To avoid of such damage, you must ensure the power supply is stable and grounded. You are recommended to use the UPS, or the multiple power supply if permitted.

The voltage should be 220V 4%, the sudden change should be 220V 15%, and frequency should be 50Hz 0.5Hz.

Make the neutral line and GND line connections correct, and the voltage between them must be less than 1 V.

Grounding for AC power supply system: ensure the GND line is properly connected. The grounding for the chassis is recommended.

Grounding for DC power supply system: the chassis must be properly grounded.

Connect all power cords before applying power to the redundant power supply module.

1.1.2 Temperature and Humidity of Equipment Room

Item Requirement

Working temperature 5 C to 40 C (41 F to 104 F)

temperature equipment room 21 C 25 C (69.8 F 77 F)

Storage temperatue -40 C to +70 C (-40 F to +158 F)

Temperature change rate < 5 C/h (non-condensing)

Working humidity 20% RH to 80% RH

Storage humidity 5% RH to 95% RH

Location Equipment room should be dust-free, and away from harmful gas, and inflammable and explosive objects. Environment with electromagnetic interference, strong virbation, noise, and unstable voltage is also not recommended.

DS-AT1000S Series Storage System Quick Start Guide

6

Construction The area of the equipment room should meet the requirements of equipment installation and capacity expansion. And the ground can bear product loading. The rooting facilities should be well designed and ready.

Air conditioner Install an air conditioner which supports power off restart function in the machine room. The installation position of air conditioning should ensure no air will blow to the equipment directly.

Ventilation and heat dissipation

To guarantee the equipments can be well ventilated, the distance between the cabinet and the wall shall not be less than 100 cm, and the distance between two cabinets shall not be less than 120 cm. It is recommended to reserver 1U space between two equipments. Ensure aire can effectively convect between the cabinet and the equipment room.

Dust-free For the equipment room locating near the dust source (coal mine, rural road, farmland, etc.), the windows and doors should be able to keep out the wind and sand.

Transportation Pack the equipment into the package. Do not transport via open truck or open warehouse. And do not transport the equipment with inflammable, explosive, and corrosive goods. Protect the equipment from rain, dust, and damage.

Particulate pollutant 0.5 m. Dust in static air should be less than 18,000 in each litre.

Corrosive gas concentration The corrosion rate of copper test plate must be lower than 300 c in each month. (According to the requirements of G1 level on corrosive gas in ANSId/ISAe-71.04-1985 standard)

Floor bearing capability Floor load-bearing capability requirement is 600 kg/m2. The height from the floor to the ceiling should be larger than 2.7M. The required load-bearing capacity for the rack is 10 KG multiply by device chassis size. E.g., a 4U equipment requires 40 KG bearing capability.

Vertical and horizontal vibration acceleration on floor surface

When the equipment is halted, acceleration value should not be larger than 0.5m/S2.

Grounding Ensure that each equipment is grounded. Serial grounding is not allowd. The resistance between the equipment shell and earth must be less than 4 .

is a length unit. 1 = 1/10,000,000,000 m

DS-AT1000S Series Storage System Quick Start Guide

7

1.2 Installation and Initial Power-on

The device shall be placed on the fixed flat surface. Tilting surface is not allowed.

You can use the standard plate in the industrial cabinet or use the guide rail (not provided) to install the device to the rack. It is recommended to use the bolts to fix the device to the rack through the mounting screw holes on the rack.

Connect all the power cords of the device to the power socket and wait for 12 hours before starting up. The temperature of the device and the equipment room must be consistent to prevent the damage caused by a huge temperature difference.

If the device has been transported and stored for more than 10 days; perform the previous operation and then start up and run the device for 30 minutes without the hard disks. And then you shut down the device, insert the hard disks and start the device again.

1.3 Notes for Installation

The device is a high-precision equipment. Please keep stable and gentle when moving it.

Installation and running environment must meet standards. Take regular investigations and records for the equipment room, or apply a remote monitoring for the working status of the device.

Do not unplug the power cord when the device is running.

In case of alarm beeper produced during the system running, please take immediate check and solution.

DS-AT1000S Series Storage System Quick Start Guide

8

Chapter 2 Appearance and Installation

2.1 Device Appearance

The system adopts rack-mounted chassis which provides LED indicators for the system status.

2.1.1 Chassis Overall View

Figure 2-1 Overall View of DS-AT1000S/360, DS-AT1000S/440, and DS-AT1000S/480

Figure 2-2 Overall View of DS-AT1000S/160, DS-AT1000S/240, DS-AT1000S/300, and DS-AT1000S/320

2.1.2 Front Panel

The disk slots view of the device is shown below.

Hard disks of 3.5 inches are supported. As shown above, slot order obeys the principle of left to right and bottom to top. The HDDs in bottom floor, from left to right, are HDD ~. The HDDs in second floor, from left to right, are HDD ~. And so on.

DS-AT1000S Series Storage System Quick Start Guide

9

Figure 2-3 Front Panel of DS-AT1000S/360, DS-AT1000S/440, and DS-AT1000S/480

Figure 2-4 Front Panel of DS-AT1000S/160, DS-AT1000S/240, DS-AT1000S/300, and DS-AT1000S/320

2.1.3 Description of Buttons in Front Panel

DS-AT1000S/360, DS-AT1000S/440, and DS-AT1000S/480

Figure 2-5 Front Panel Buttons

Figure 2-6 Button Description

Button Name Description

Power switch and indicator When the system is off, press the button to turn on it.

When the system is running, hold the button for at least 4s and not more than 15s to turn off the

DS-AT1000S Series Storage System Quick Start Guide

10

DS-AT1000S/160, DS-AT1000S/240, DS-AT1000S/300, and DS-AT1000S/320

Figure 2-7 Front Panel Buttons

Figure 2-8 Button Description

system.

The indicator shows green when the system is running.

Positioning button and indicator

Press this button or click Positioning on GUI to trigger locating function. Press the button again to disable locating function.

The indicator flashes in blue when locating function is triggered.

Mute button and alarm indicator

When an alarm is triggered, the indicator flashes in red and buzzer beeps. Press the button to stop beeping.

Power indicator for controller A When controller A is connected and is running, the

indicator is green.

Power indicator for controller B When controller B is connected and is running, the

indicator is green.

Fault indicator for controller A When a fault occurs in controller A, the indicator

flashes in red.

When controller A does not exit, the indicator is unlit.

Fault indicator for controller B When a fault occurs in controller B, the indicator

flashes in red.

When controller B does not exit, the indicator is unlit.

Button Name Description

DS-AT1000S Series Storage System Quick Start Guide

11

2.1.4 Rear Panel

DS-AT1000S/360, DS-AT1000S/440, and DS-AT1000S/480

Figure 2-9 Rear Panel

Power switch and indicator When the system is off, press the button to turn on it.

When the system is running, hold the button for at least 4s and not more than 15s to turn off the system.

The indicator shows green when the system is running.

Positioning button and indicator

Press this button or click Positioning on GUI to trigger locating function. Press the button again to disable locating function.

The indicator flashes in blue when locating function is triggered.

Mute button and alarm indicator

When an alarm is triggered, the indicator flashes in red and buzzer beeps. Press the button to stop beeping.

DS-AT1000S Series Storage System Quick Start Guide

12

Table 2-1 Description

No. Name No. Name

1 Power module 1 8 SAS interface

2 COM interface 9 Data network interface 3

3 Two USB interfaces 10 Management network interface

4 Two USB interfaces 11 Power module 2

5 Data network interface 1 12 IPMI

6 Data network interface 2 13 Data network interface 4

7 VGA interface

DS-AT1000S/160, DS-AT1000S/240, DS-AT1000S/300, and DS-AT1000S/320

Figure 2-10 Rear Panel

DS-AT1000S Series Storage System Quick Start Guide

13

Table 2-2 Description

No. Name No. Name

1 Power module 1 9 HDMI interface 2

2 HDMI interface 1 10 USB interface 2

3 USB interface 1 11 Data LAN 2

4 Data LAN 1 12 Management LAN

5 Data LAN 3 13 EXP interface 2

6 EXP interface 1 14 RS-232 interface

7 RS-485 interface 15 Fan module

8 Power module 2

2.2 Install Accessories

2.2.1 Installation Requirement

Before installation, please check whether following objects are in the package.

Storage system

Power cord

Gigabit Ethernet cable

Delivered CD

Screw package

The following accessories are optional or user-provided:

Gigabit Ethernet switch

Rack guide rail

Following the installation requirements to install the storage system. Before powering on your storage system, please check the following hardware connection:

Connect the power cord to 220 VAC power supply.

Use the delivered Ethernet cable to connect all data network interfaces to a gigabit network switch.

Serial port of the storage system, if any, is mainly designed for debugging. You are recommended to use it with the help of our technical support.

DS-AT1000S Series Storage System Quick Start Guide

14

2.2.2 Install HDD

Selecting HDD Model

It is recommended to adopt the certificated professional HDD models so as to ensure the stable running of the system and the reliable data storage. You are recommended to use the HDD in recommended HDD list. Please contact our technical support for the recommended HDD list.

In order to avoid damages during transportation, it is recommended to package and transport the

hard disks separately with the chassis of network storage system.

Installing HDD

Follow the steps below to install HDDs.

Step 1 Remove the front panel cover.

1) Unlock the front panel cover with delivered key.

2) Hold the cover and pull it out till it gets out of the control of the lock.

3) Move the cover to right to remove it from front panel.

Step 2 Press the spring lock of the HDD on the left, drag the handle and then pull out the dummy HDD from the chassis along the guide rail.

Step 3 (Optional) Remove the baffle, if any, from the dummy HDD.

Baffle

Figure 2-11 Remove Baffle

Step 4 Use four screws to secure the HDD (with the PCB side downward) to the bracket. In order to ensure the HDD pin holds the line with the rear of the plate, mount screws to the specific screw hole as shown.

DS-AT1000S Series Storage System Quick Start Guide

15

Figure 2-12 Splitting HDD Plate

Figure 2-13 Secure HDD

Step 5 Insert the HDD bracket (with the PCB side towards the left of the chassis) to the chassis and push it along the guide apparatus to the bottom. Then, press the securing handle to ensure the bracket has been seated into position and lock it.

Step 6 Repeat the operating steps above till all HDDs have been installed.

Indicators in Dummy HDD

Two indicators are provided.

When the HDD is normal, the blue indicator is on.

When the HDD is unavailable, the red indicator is on.

When the HDD is in positioning or detecting status, the red indicator flashes.

DS-AT1000S Series Storage System Quick Start Guide

16

Figure 2-14 Indicators in Dummy HDD

Precautions during HDD Installation

When you plug or unplug the hard disks, please take the following precautions:

When the HDD is running, the maximum vibration is can suffer is 0.25 Gs. While when it is idle, the maximum vibration is 3.0 Gs.

Please use the provided screws to fix the four edges of the dummy HDD.

Make sure the HDD mounting bracket is steadily plugged into the chassis along the slot.

When you unplug the hard disk, unplug it about 3cm away from the chassis and then make it stay about 30 seconds on the slot guide before totally unplug it from the chassis. Since the discs of the hard disk are still spinning at a high speed just after powering off, unplugging the hard disk immediately will damage the discs.

The system supports HDD hot swapping, yet the data storage safety is not ensured.

Please avoid frequent plugging/unplugging of the hard disks during the system running so as to maintain long service life of the hard disks.

Take regular check and examine of the working status of the hard disks every two months, or configure the system with auto check and examine task.

Please avoid unplugging a hard disk when it is writing or reading data so as to prevent data loss.

2.3 Startup

Obey the following rules to operate startup and shutdown:

Step 1 Connect all the power cords to the redundancy power supply module before applying power.

Step 2 Press the power button on the device. It may take 5 to 10 minutes to finish the startup process. After startup, storage system will send out beep sound.

DS-AT1000S Series Storage System Quick Start Guide

17

Check the connection between components if device cannot start up normally.

Do not press the power button after startup, or device will be forced to shut down and may

course the data loss.

2.4 Shutdown

Step 1 Log in the storage system via Internet Explore. For details, refer to 4.1 Activate Storage System.

Step 2 Go to Device > Device Overview.

Figure 2-15 More Operations

Step 3 Click More Operations.

Step 4 Click Device Restart or Device Shutdown as your desire.

DS-AT1000S Series Storage System Quick Start Guide

18

Chapter 3 Function Configuration

Step 1 Configure network parameters. For details, refer to 4.2 Configure Network Parameters.

Step 2 Operate quick configuration. For details, refer to 5.1 One-Key Configuration.

Step 3 Format storage space. For details, refer to 5.2 Format Storage Space.

Step 4 Configure Hybrid SAN parameters. For details, refer to Chapter 6 Basic Configuration.

DS-AT1000S Series Storage System Quick Start Guide

19

Chapter 4 Network

You are recommended to connect all the network interfaces to the Internet.

4.1 Activate Storage System

Purpose

For the first-time access, you need to activate the storage system by setting an admin password. No operation is allowed before activation. You can only use Internet Explorer 8.0 and above to visit storage system.

Step 1 Use an Ethernet cable to connect your computer and the management network interface of storage system.

Step 2 Set your computer IP address. Ensure it is in the same network segment with the storage system.

Default IP address of management network interface is 10.254.254.254.

Step 3 Visit https://10.254.254.254:2004 in web browser to access the storage system.

Step 4 Create password for storage system and confirm it.

STRONG PASSWORD RECOMMENDED We highly recommend you create a strong password of your own choosing (using a minimum of 8 characters, including upper case letters, lower case letters, numbers, and special characters) in order to increase the security of your product. And we recommend you reset your password regularly, especially in the high security system, resetting the password monthly or weekly can better protect your product.

Step 5 Click Enter to activate the storage system.

4.2 Configure Network Parameters

4.2.1 Modify Network Parameters

Step 1 Go to Device > Information > Modify Network.

DS-AT1000S Series Storage System Quick Start Guide

20

Figure 4-1 Modify Network

Step 2 You can view binding network information and modify binding parameters.

Figure 4-2 Modify Network

DS-AT1000S/360, DS-AT1000S/440, and DS-AT1000S/480 series storage system contains 5 network interfaces. By default, network interface 1 and 4 are bonded as a data network interface (bond network interface 1) and bonding mode is XOR.

DS-AT1000S/160, DS-AT1000S/240, DS-AT1000S/300, and DS-AT1000S/320 series storage system contains 4 network interfaces. By default, network interface 1 and 3 are bonded as a data network interface (bond network interface 1) and bonding mode is XOR. Network interface 4 is management network interface.

Configure static link aggregation and disable LACP for the network switch

DS-AT1000S Series Storage System Quick Start Guide

21

You are not recommended to delete the default binding.

If you forget the IP address of data network interface, you can log in storage system via management network interface to view the IP address. Default IP address of management network interface is 10.254.254.254.

4.2.2 Modify IP Address of Bond Network Interface

Step 1 Go to Device > Information > Modify Network.

Step 2 Click Settings of bond network interface 1.

Figure 4-3 Set Bound Port

Step 3 Modify network parameters.

Step 4 Click OK.

Connect all the bonded network interfaces to a network switch.

Management network interface cannot be bonded.

DS-AT1000S Series Storage System Quick Start Guide

22

Chapter 5 System Configuration

5.1 One-Key Configuration

Before you start one-key configuration, ensure the number of HDD meets the following requirement.

DS-AT1000S/160 storage system requires at least 8 HDDs.

DS-AT1000S/240 storage system requires at least 12 HDDs.

DS-AT1000S/300 storage system requires at least 15 HDDs.

DS-AT1000S/320 storage system requires at least 16 HDDs.

DS-AT1000S/360 storage system requires at least 18 HDDs.

DS-AT1000S/440 storage system requires at least 22 HDDs.

DS-AT1000S/480 storage system requires at least 24 HDDs.

Step 1 Single controller device will automatically create domain after startup.

Domain IP address: 1.1.1.1. Domain subnet mask: 255.255.255.0.

Step 2 After logged into the system, the configuration wizard will pop up and the system will automatically detect environment.

Step 3 After the three environment detections are passed, click One-Key Configuration and follow the wizard to configure the system.

DS-AT1000S Series Storage System Quick Start Guide

23

Figure 5-1 Wizard

The configuration process takes a certain time. The following prompt will pop up after configuration finishes.

Figure 5-2 Prompt

5.2 Format Storage Space

5.2.1 Activate Hybrid SAN Sub-System

Purpose

You can only use Internet Explorer 8.0 and above to visit Hybrid SAN sub-system.

Step 1 Visit http://IP address of bond network interface 1 in web browser to access Hybrid SAN sub-system.

Step 2 Create password for Hybrid SAN sub-system and confirm it.

DS-AT1000S Series Storage System Quick Start Guide

24

STRONG PASSWORD RECOMMENDED We highly recommend you create a strong password of your own choosing (using a minimum of 8 characters, including upper case letters, lower case letters, numbers, and special characters) in order to increase the security of your product. And we recommend you reset your password regularly, especially in the high security system, resetting the password monthly or weekly can better protect your product.

Step 3 Click Enter to activate Hybrid SAN sub-system.

5.2.2 Format Storage Space

Step 1 Go to Configuration > Storage > Storage Management.

Figure 5-3 Storage Space Management

Step 2 Select storage space and click Format.

DS-AT1000S Series Storage System Quick Start Guide

25

Chapter 6 Basic Configuration

Log in to Hybrid SAN sub-system and follow the steps to configure basic parameters.

6.1 Camera Management

Step 1 Log in to Hybrid SAN sub-system. For details, refer to 5.2.1 Activate Hybrid SAN Sub-System.

Step 2 Go to Configuration > System > Camera Management.

Figure 6-1 Camera Management

Step 3 Add network cameras. Choose from:

Manual Add: Enter the network camera information to add it.

1) Click Add.

Figure 6-2 Add Network Camera

DS-AT1000S Series Storage System Quick Start Guide

26

2) Enter network camera information. The information must be the same with the information of network camera to add.

3) Click OK.

Quick Add: Add network cameras of the same password and in the same network segment the storage system.

1) Click Quick Add. Network cameras in the same network segment with the storage system will be listed.

2) Check network cameras to add and click OK. Network cameras of the same password with the storage system will be successfully added.

6.2 Configure Recording Schedule

Purpose

By default, network cameras start continuous recording after successfully added. Follow the steps to configure recording schedules.

Step 1 Log in to Hybrid SAN sub-system. For details, refer to 5.2.1 Activate Hybrid SAN Sub-System.

Step 2 Go to Configuration > Storage > Schedule Settings.

Figure 6-3 Record Schedule

Step 3 Select IP Camera No. and check Enable.

Step 4 Select schedule type.

Step 5 Drag on the table to draw the recording schedule.

Step 6 Click Save.

DS-AT1000S Series Storage System Quick Start Guide

27

6.3 Live View

Go to Live View. You can preview live images, start manual recording, capture pictures, turn on live view aud

Manualsnet FAQs

If you want to find out how the DS-240 Hikvision works, you can view and download the Hikvision DS-240 Storage Quick Start Guide on the Manualsnet website.

Yes, we have the Quick Start Guide for Hikvision DS-240 as well as other Hikvision manuals. All you need to do is to use our search bar and find the user manual that you are looking for.

The Quick Start Guide should include all the details that are needed to use a Hikvision DS-240. Full manuals and user guide PDFs can be downloaded from Manualsnet.com.

The best way to navigate the Hikvision DS-240 Storage Quick Start Guide is by checking the Table of Contents at the top of the page where available. This allows you to navigate a manual by jumping to the section you are looking for.

This Hikvision DS-240 Storage Quick Start Guide consists of sections like Table of Contents, to name a few. For easier navigation, use the Table of Contents in the upper left corner.

You can download Hikvision DS-240 Storage Quick Start Guide free of charge simply by clicking the “download” button in the upper right corner of any manuals page. This feature allows you to download any manual in a couple of seconds and is generally in PDF format. You can also save a manual for later by adding it to your saved documents in the user profile.

To be able to print Hikvision DS-240 Storage Quick Start Guide, simply download the document to your computer. Once downloaded, open the PDF file and print the Hikvision DS-240 Storage Quick Start Guide as you would any other document. This can usually be achieved by clicking on “File” and then “Print” from the menu bar.