Hikvision DS-K1802 Reader User's Manual PDF

DS-K1802 Series Card Reader

User Manual

DS-K1802 Series Card Reader

i

2021 Hangzhou Hikvision Digital Technology Co., Ltd. All rights

reserved.

About this Manual

The Manual includes instructions for using and managing the

Product. Pictures, charts, images and all other information

hereinafter are for description and explanation only. The

information contained in the Manual is subject to change,

without notice, due to firmware updates or other reasons. Please

find the latest version of this Manual at the Hikvision website

(https://www.hikvision.com/).

Please use this Manual with the guidance and assistance of

professionals trained in supporting the Product.

Trademarks

and other Hikvisions trademarks and logos are

the properties of Hikvision in various jurisdictions.

Other trademarks and logos mentioned are the properties of

their respective owners.

Disclaimer

TO THE MAXIMUM EXTENT PERMITTED BY APPLICABLE LAW, THIS

MANUAL AND THE PRODUCT DESCRIBED, WITH ITS HARDWARE,

SOFTWARE AND FIRMWARE, ARE PROVIDED AS IS AND WITH

ALL FAULTS AND ERRORS. HIKVISION MAKES NO WARRANTIES,

EXPRESS OR IMPLIED, INCLUDING WITHOUT LIMITATION,

MERCHANTABILITY, SATISFACTORY QUALITY, OR FITNESS FOR A

PARTICULAR PURPOSE. THE USE OF THE PRODUCT BY YOU IS AT

YOUR OWN RISK. IN NO EVENT WILL HIKVISION BE LIABLE TO YOU

FOR ANY SPECIAL, CONSEQUENTIAL, INCIDENTAL, OR INDIRECT

DAMAGES, INCLUDING, AMONG OTHERS, DAMAGES FOR LOSS OF

BUSINESS PROFITS, BUSINESS INTERRUPTION, OR LOSS OF DATA,

DS-K1802 Series Card Reader

ii

CORRUPTION OF SYSTEMS, OR LOSS OF DOCUMENTATION,

WHETHER BASED ON BREACH OF CONTRACT, TORT (INCLUDING

NEGLIGENCE), PRODUCT LIABILITY, OR OTHERWISE, IN

CONNECTION WITH THE USE OF THE PRODUCT, EVEN IF

HIKVISION HAS BEEN ADVISED OF THE POSSIBILITY OF SUCH

DAMAGES OR LOSS.

YOU ACKNOWLEDGE THAT THE NATURE OF THE INTERNET

PROVIDES FOR INHERENT SECURITY RISKS, AND HIKVISION SHALL

NOT TAKE ANY RESPONSIBILITIES FOR ABNORMAL OPERATION,

PRIVACY LEAKAGE OR OTHER DAMAGES RESULTING FROM

CYBER-ATTACK, HACKER ATTACK, VIRUS INFECTION, OR OTHER

INTERNET SECURITY RISKS; HOWEVER, HIKVISION WILL PROVIDE

TIMELY TECHNICAL SUPPORT IF REQUIRED.

YOU AGREE TO USE THIS PRODUCT IN COMPLIANCE WITH ALL

APPLICABLE LAWS, AND YOU ARE SOLELY RESPONSIBLE FOR

ENSURING THAT YOUR USE CONFORMS TO THE APPLICABLE LAW.

ESPECIALLY, YOU ARE RESPONSIBLE, FOR USING THIS PRODUCT

IN A MANNER THAT DOES NOT INFRINGE ON THE RIGHTS OF

THIRD PARTIES, INCLUDING WITHOUT LIMITATION, RIGHTS OF

PUBLICITY, INTELLECTUAL PROPERTY RIGHTS, OR DATA

PROTECTION AND OTHER PRIVACY RIGHTS. YOU SHALL NOT USE

THIS PRODUCT FOR ANY PROHIBITED END-USES, INCLUDING THE

DEVELOPMENT OR PRODUCTION OF WEAPONS OF MASS

DESTRUCTION, THE DEVELOPMENT OR PRODUCTION OF

CHEMICAL OR BIOLOGICAL WEAPONS, ANY ACTIVITIES IN THE

CONTEXT RELATED TO ANY NUCLEAR EXPLOSIVE OR UNSAFE

NUCLEAR FUEL-CYCLE, OR IN SUPPORT OF HUMAN RIGHTS

ABUSES.

IN THE EVENT OF ANY CONFLICTS BETWEEN THIS MANUAL AND

THE APPLICABLE LAW, THE LATTER PREVAILS.

DS-K1802 Series Card Reader

iii

Regulatory Information

FCC Information

Please take attention that changes or modification not expressly

approved by the party responsible for compliance could void the

users authority to operate the equipment.

FCC compliance: This equipment has been tested and found to

comply with the limits for a Class B digital device, pursuant to part

15 of the FCC Rules. These limits are designed to provide

reasonable protection against harmful interference in a residential

installation. This equipment generates, uses and can radiate radio

frequency energy and, if not installed and used in accordance

with the instructions, may cause harmful interference to radio

communications. However, there is no guarantee that

interference will not occur in a particular installation. If this

equipment does cause harmful interference to radio or television

reception, which can be determined by turning the equipment off

and on, the user is encouraged to try to correct the interference

by one or more of the following measures:

Reorient or relocate the receiving antenna.

Increase the separation between the equipment and receiver.

Connect the equipment into an outlet on a circuit different

from that to which the receiver is connected.

Consult the dealer or an experienced radio/TV technician for

help.

The device must not be co-located or operating in conjunction

with any other antenna or transmitter.

This equipment should be installed and operated with a minimum

distance 20cm between the radiator and your body.

FCC Conditions

DS-K1802 Series Card Reader

iv

This device complies with part 15 of the FCC Rules. Operation is

subject to the following two conditions:

1. This device may not cause harmful interference.

2. This device must accept any interference received, including

interference that may cause undesired operation. EU Conformity Statement

This product and - if applicable - the supplied accessories too are marked with "CE" and comply therefore with the applicable harmonized European standards listed under

the EMC Directive 2014/30/EU, the RoHS Directive 2011/65/EU.

2012/19/EU (WEEE directive): Products marked with this symbol cannot be disposed of as unsorted municipal waste in the European Union. For proper recycling, return this product to your local supplier upon the purchase of equivalent new equipment, or

dispose of it at designated collection points. For more information see: www.recyclethis.info.

2006/66/EC (battery directive): This product contains a battery that cannot be disposed of as unsorted municipal waste in the European Union. See the product documentation for specific battery information. The battery is marked with this symbol, which may include lettering to

indicate cadmium (Cd), lead (Pb), or mercury (Hg). For proper recycling, return the battery to your supplier or to a designated collection point. For more information see: www.recyclethis.info.

Industry Canada ICES-003 Compliance

DS-K1802 Series Card Reader

v

This device meets the CAN ICES-3 (A)/NMB-3(A) standards requirements.

Use only power supplies listed in the user instructions:

Model Manufacturer Standard

TS-A018-120015Ec Shenzhen Transin

Technologies Co., Ltd

CEE

Safety Instruction These instructions are intended to ensure that user can use the product correctly to avoid danger or property loss. The precaution measure is divided into Warnings and Cautions: Warnings: Neglecting any of the warnings may cause serious injury or death. Cautions: Neglecting any of the cautions may cause injury or equipment damage.

Warnings

All the electronic operation should be strictly compliance with the electrical

safety regulations, fire prevention regulations and other related regulations in

your local region.

Please use the power adapter, which is provided by normal company. The power

consumption cannot be less than the required value.

Do not connect several devices to one power adapter as adapter overload may

cause over-heat or fire hazard.

Warnings Follow these safeguards to prevent serious injury or death.

Cautions Follow these precautions to prevent potential injury or material damage.

DS-K1802 Series Card Reader

vi

Please make sure that the power has been disconnected before you wire, install

or dismantle the device.

When the product is installed on wall or ceiling, the device shall be firmly fixed.

If smoke, odors or noise rise from the device, turn off the power at once and

unplug the power cable, and then please contact the service center.

If the product does not work properly, please contact your dealer or the nearest

service center. Never attempt to disassemble the device yourself. (We shall not

assume any responsibility for problems caused by unauthorized repair or

maintenance.)

Cautions

Do not drop the device or subject it to physical shock, and do not expose it to

high electromagnetism radiation. Avoid the equipment installation on

vibrations surface or places subject to shock (ignorance can cause equipment

damage).

Do not place the device in extremely hot (refer to the specification of the device

for the detailed operating temperature), cold, dusty or damp locations, and do

not expose it to high electromagnetic radiation. The appropriate temperature

is -20 to 65.

The device cover for indoor use shall be kept from rain and moisture.

Exposing the equipment to direct sun light, low ventilation or heat source such

as heater or radiator is forbidden (ignorance can cause fire danger).

Do not aim the device at the sun or extra bright places. A blooming or smear

may occur otherwise (which is not a malfunction however), and affecting the

endurance of sensor at the same time.

Please use a soft and dry cloth when clean inside and outside surfaces of the

device cover, do not use alkaline detergents.

Please keep all wrappers after unpack them for future use. In case of any failure

occurred, you need to return the device to the factory with the original

wrapper. Transportation without the original wrapper may result in damage on

the device and lead to additional costs.

DS-K1802 Series Card Reader

vii

Improper use or replacement of the battery may result in hazard of explosion.

Replace with the same or equivalent type only. Dispose of used batteries

according to the instructions provided by the battery manufacturer.

Preventive and Cautionary Tips

To guarantee the card reader works properly, please read and

obey the notes below.

If the card reader is powered by the controller, the power

supply distance is recommended to be no longer than 100m.

If the distance is longer than 100m, you are advised to power

the card reader by external 12V (range: -%10 ~ +%10) DC

power supply, which is nonswitched and linear.

To guarantee the communication between the controller and

the card reader, you must use RVVP cable above 0.5 to

connect them.

If the card reader is installed outside or in environment easy

to permeable, it is advisable to install a waterproof shield.

If you need to install several card readers, the distance

among them must over 30cm.

To reduce the noise in long distance transmission, the shield

of cable should connect to the GND of both controller and

card reader terminal.

Please take care of your card and report card loss in time

when card is lost.

If you require a higher security level, use multiple

authentication modes.

Multiple card types are supported. Please select an

appropriate card type according to the card performance and

the usage scenarios.

DS-K1802 Series Card Reader

viii

Content Chapter 1 Introduction ............................................................ 1

1.1 Over View ...................................................................... 1 1.2 Indicator and Component .............................................. 2

Chapter 2 Installation .............................................................. 2 2.1 Definition of Cable ......................................................... 2 2.2 Wiring Cables ................................................................ 3 2.3 Installing Card Reader .................................................... 4

Chapter 3 Sound Prompt and Indicator ................................... 5

DS-K1802 Series Card Reader

1

Chapter 1 Introduction

1.1 Over View

With Keypad Without Keypad

Figure 1-1 DS-K1802 Series Card Reader

DS-K1802 series card reader is a kind of high-performance

product. It communicates with access controller via Wiegand

protocol. As to the physical appearance, the PC+ABS material

makes water proof and dust proof possible in poor environment.

DS-K1802 Series Card Reader

2

1.2 Indicator and Component

Figure 1-2 Indicator and Component

Chapter 2 Installation

2.1 Definition of Cable The description of cables is shown below.

Table 2-1 Description of Cable

Color Description

Red PWR (12 VDC)

Black GND

Purple Beep Control

Brown OK

Orange ERR

Green Wiegand W0

DS-K1802 Series Card Reader

3

Color Description

White Wiegand W1

Blue Wiegand 26/ 34

2.2 Wiring Cables Purpose:

Wire the cables between controller and card reader, thus to

establish the communication between them.

Steps for Wiegand communication mode:

1. Set the Wiegand mode before power-on:

Cable Wiring Method Wiegand Mode

Blue Wiegand Cable Grounded Wiegand 26

Not Grounded Wiegand 34

2. Wiring the cable between controller and card reader as

shown below.

Y e

llo w

B lu

e

B la

ck

R e

d B

la ck

R e

d

G re

e n

W h

it e

P u

rp le

O ra

n ge

B ro

w n

Controller

Card Reader

Y e

llo w

B lu

e

B la

ck

R e

d

B la

ck

R e

d

G re

e n

W h

it e

P u

rp le

O ra

n ge

B ro

w n

Controller

Card Reader

Card Reader Card Reader

E R

R

O K

Figure 2-1 Wiring for Wiegand Communication Mode

DS-K1802 Series Card Reader

4

2.3 Installing Card Reader Steps:

1. Fix the plate on the wall or

other places by using two

screws (PA425-SUS). Make sure

the arrows on the plate are

upwards.

2. Check whether the plate is fixed

and in the right direction.

3. Slide the card reader from the

direction A to B along the plate

side until the bottom matches

the joint. Make sure the card

reader is tightly on the wall or

other places.

4. Drag and move the card reader

to make sure it is fixed.

DS-K1802 Series Card Reader

5

Chapter 3 Sound Prompt and Indicator

After the card reader is powered on, LED status indicator will turn

green and blink for 1 time. Then it will turn red and blink for 3

times. At last the buzzer will send out a beep sound indicating the

starting up process is completed.

When using the card reader, it will send out different sounds

prompt and the LED indicator to indicate different statuses. You

can refer to tables below for detailed information.

Table3-1 Description of Prompt Sound

Sound Prompt Description

One beep

Swiping card prompt

Pressing keys prompt

Prompt for too long card No. input by pressing keys.

Time out prompt for pressing keys or swiping card.

For Card + Password authentication: prompt for entering the password after swiping the card.

Two rapid beeps The operation of pressing keys or swiping card is valid.

Three slow beeps The operation of pressing keys or swiping card is invalid.

Rapidly continuous beeps

Prompt for tamper-proof alarm.

Prompt for buzzer alarm.

Slowly continuous beeps

The card reader is unencrypted.

DS-K1802 Series Card Reader

6

Table 3-2 Description of LED Indicator

LED Indicator Status Description

Green (blink for 1 time), and red (blink for 3 times)

The card reader is power on.

Green and slow blinking

For Card + Password authentication: prompt for entering the password after swiping the card.

Solid green for 3s The operation of pressing keys or swiping card is valid.

Solid red Card reader is working normally.

Red and blink for 3 times

The operation of pressing keys or swiping card is invalid.

<