Hikvision DS-K1101M Reader User's Manual PDF

DS-K1100 Series Card Reader User Manual

DS-K1100 Series Card Reader

i

User Manual 2020 Hangzhou Hikvision Digital Technology Co., Ltd.

ALL RIGHTS RESERVED. Any and all information, including, among others, wordings, pictures, graphs are the properties of Hangzhou Hikvision Digital Technology Co., Ltd. or its

subsidiaries (hereinafter referred to be Hikvision). This user manual (hereinafter referred to be the Manual) cannot be reproduced, changed, translated, or distributed, partially or wholly, by any means, without the

prior written permission of Hikvision. Unless otherwise stipulated, Hikvision does not make any warranties, guarantees or representations, express or implied, regarding to the Manual.

This Manual is applicable to card reader.

Series Models Description

DS-K1101 Series

DS-K1101M MIFARE card reader (without keypad)

DS-K1101MK MIFARE card reader (with a keypad)

DS-K1102 Series

DS-K1102M MIFARE card reader (without keypad)

DS-K1102MK MIFARE card reader (with a keypad)

DS-K1102E EM card reader (without keypad)

DS-K1102 EK EM card reader (with a keypad)

DS-K1102 EM Dual-band card reader(without keypad)

DS-K1102 EMK Dual-band card reader(with a keypad)

DS-K1103 Series

DS-K1103M MIFARE card reader (without keypad)

DS-K1103MK MIFARE card reader (with a keypad)

DS-K1104 Series

DS-K1104M MIFARE card reader (without keypad)

DS-K1104MK MIFARE card reader (with a keypad)

About this Manual

This Manual is subject to domestic and international copyright protection. Hangzhou Hikvision Digital Technology Co., Ltd. (Hikvision) reserves all rights to this manual. This manual cannot be reproduced, changed,

translated, or distributed, partially or wholly, by any means, without the prior written permission of Hikvision. Trademarks

and other Hikvisions trademarks and logos are the properties of Hikvision in various jurisdictions. Other trademarks and logos mentioned below are the properties of their respective owners.

Legal Disclaimer

DS-K1100 Series Card Reader

ii

TO THE MAXIMUM EXTENT PERMITTED BY APPLICABLE LAW, THE PRODUCT DESCRIBED, WITH ITS HARDWARE, SOFTWARE AND FIRMWARE, IS

PROVIDED "AS IS", WITH ALL FAULTS AND ERRORS, AND HIKVISION MAKES NO WARRANTIES, EXPRESS OR IMPLIED, INCLUDING WITHOUT LIMITATION, MERCHANTABILITY, SATISFACTORY QUALITY, FITNESS FOR A PARTICULAR

PURPOSE, AND NON-INFRINGEMENT OF THIRD PARTY. IN NO EVENT WILL HIKVISION, ITS DIRECTORS, OFFICERS, EMPLOYEES, OR AGENTS BE LIABLE TO YOU FOR ANY SPECIAL, CONSEQUENTIAL, INCIDENTAL, OR INDIRECT

DAMAGES, INCLUDING, AMONG OTHERS, DAMAGES FOR LOSS OF BUSINESS PROFITS, BUSINESS INTERRUPTION, OR LOSS OF DATA OR DOCUMENTATION, IN CONNECTION WITH THE USE OF THIS PRODUCT,

EVEN IF HIKVISION HAS BEEN ADVISED OF THE POSSIBILITY OF SUCH DAMAGES. REGARDING TO THE PRODUCT WITH INTERNET ACCESS, THE USE OF

PRODUCT SHALL BE WHOLLY AT YOUR OWN RISKS. HIKVISION SHALL NOT TAKE ANY RESPONSIBILITIES FOR ABNORMAL OPERATION, PRIVACY LEAKAGE OR OTHER DAMAGES RESULTING FROM CYBER ATTACK, HACKER

ATTACK, VIRUS INFECTION, OR OTHER INTERNET SECURITY RISKS; HOWEVER, HIKVISION WILL PROVIDE TIMELY TECHNICAL SUPPORT IF REQUIRED.

SURVEILLANCE LAWS VARY BY JURISDICTION. PLEASE CHECK ALL RELEVANT LAWS IN YOUR JURISDICTION BEFORE USING THIS PRODUCT IN ORDER TO ENSURE THAT YOUR USE CONFORMS THE APPLICABLE LAW. HIKVISION

SHALL NOT BE LIABLE IN THE EVENT THAT THIS PRODUCT IS USED WITH ILLEGITIMATE PURPOSES. IN THE EVENT OF ANY CONFLICTS BETWEEN THIS MANUAL AND THE

APPLICABLE LAW, THE LATER PREVAILS.

DS-K1100 Series Card Reader

iii

Regulatory Information

FCC Information

Please take attention that changes or modification not expressly approved

by the party responsible for compliance could void the users authority to

operate the equipment.

FCC compliance: This equipment has been tested and found to comply with

the limits for a Class B digital device, pursuant to part 15 of the FCC Rules.

These limits are designed to provide reasonable protection against harmful

interference in a residential installation. This equipment generates, uses and

can radiate radio frequency energy and, if not installed and used in

accordance with the instructions, may cause harmful interference to radio

communications. However, there is no guarantee that interference will not

occur in a particular installation. If this equipment does cause harmful

interference to radio or television reception, which can be determined by

turning the equipment off and on, the user is encouraged to try to correct

the interference by one or more of the following measures:

Reorient or relocate the receiving antenna.

Increase the separation between the equipment and receiver.

Connect the equipment into an outlet on a circuit different from that to

which the receiver is connected.

Consult the dealer or an experienced radio/TV technician for help.

The device must not be co-located or operating in conjunction with any

other antenna or transmitter.

This equipment should be installed and operated with a minimum distance

20cm between the radiator and your body.

FCC Conditions

This device complies with part 15 of the FCC Rules. Operation is subject to

the following two conditions:

1. This device may not cause harmful interference.

2. This device must accept any interference received, including interference

DS-K1100 Series Card Reader

iv

that may cause undesired operation.

EU Conformity Statement

This product and - if applicable - the supplied

accessories too are marked with "CE" and

comply therefore with the applicable

harmonized European standards listed under

the RE Directive 2014/53/EU, the EMC Directive

2014/30/EU, the LVD Directive 2014/35/EU, the RoHS

Directive 2011/65/EU.

2012/19/EU (WEEE directive): Products marked

with this symbol cannot be disposed of as

unsorted municipal waste in the European Union.

For proper recycling, return this product to your

local supplier upon the purchase of equivalent

new equipment, or dispose of it at designated

collection points. For more information see:

www.recyclethis.info.

2006/66/EC (battery directive): This product

contains a battery that cannot be disposed of as

unsorted municipal waste in the European Union.

See the product documentation for specific

battery information. The battery is marked with

this symbol, which may include lettering to

indicate cadmium (Cd), lead (Pb), or mercury (Hg).

For proper recycling, return the battery to your supplier or to a designated

collection point. For more information see: www.recyclethis.info.

Industry Canada ICES-003 Compliance This device meets the CAN ICES-3 (A)/NMB-3(A) standards requirements.

DS-K1100 Series Card Reader

v

Use only power supplies listed in the user instructions:

Model Manufacturer Standard

TS-A018-120015Ec Shenzhen Transin

Technologies Co., Ltd

CEE

Safety Instruction

These instructions are intended to ensure that user can use the product

correctly to avoid danger or property loss. The precaution measure is divided into Warnings and Cautions: Warnings: Neglecting any of the warnings may cause serious injury or

death. Cautions: Neglecting any of the cautions may cause injury or equipment damage.

Warnings All the electronic operation should be strictly compliance with the

electrical safety regulations, fire prevention regulations and other related regulations in your local region.

Please use the power adapter, which is provided by normal company. The power consumption cannot be less than the required value.

Do not connect several devices to one power adapter as adapter overload may cause over-heat or fire hazard.

Please make sure that the power has been disconnected before you wire, install or dismantle the device.

When the product is installed on wall or ceiling, the device shall be firmly fixed.

Warnings Follow these safeguards to prevent

serious injury or death.

Cautions Follow these precautions to prevent potential injury or material

damage.

DS-K1100 Series Card Reader

vi

If smoke, odors or noise rise from the device, turn off the power at once and unplug the power cable, and then please contact the service center.

If the product does not work properly, please contact your dealer or the nearest service center. Never attempt to disassemble the device yourself. (We shall not assume any responsibility for problems caused by unauthorized repair or maintenance.)

Cautions Do not drop the device or subject it to physical shock, and do not expose

it to high electromagnetism radiation. Avoid the equipment installation on

vibrations surface or places subject to shock (ignorance can cause equipment damage).

Do not place the device in extremely hot (refer to the specification of the device for the detailed operating temperature), cold, dusty or damp locations, and do not expose it to high electromagnetic radiation. The appropriate temperature is -20 to 65.

The device cover for indoor use shall be kept from rain and moisture. Exposing the equipment to direct sun light, low ventilation or heat source

such as heater or radiator is forbidden (ignorance can cause fire danger). Do not aim the device at the sun or extra bright places. A blooming or

smear may occur otherwise (which is not a malfunction however), and affecting the endurance of sensor at the same time.

Please use the provided glove when open up the device cover, avoid direct contact with the device cover, because the acidic sweat of the fingers may erode the surface coating of the device cover.

Please use a soft and dry cloth when clean inside and outside surfaces of the device cover, do not use alkaline detergents.

Please keep all wrappers after unpack them for future use. In case of any failure occurred, you need to return the device to the factory with the original wrapper. Transportation without the original wrapper may result in damage on the device and lead to additional costs.

Improper use or replacement of the battery may result in hazard of explosion. Replace with the same or equivalent type only. Dispose of used batteries according to the instructions provided by the battery manufacturer.

Preventive and Cautionary Tips

DS-K1100 Series Card Reader

vii

To guarantee the card reader works properly, please read and obey the

notes below.

If the card reader is powered by the controller, the power supply

distance is recommended to be no longer than 100m. If the distance is

longer than 100m, you are advised to power the card reader by

external 12V (range: -%10 ~ +%10) DC power supply, which is

nonswitched and linear.

To guarantee the communication between the controller and the card

reader, you must use RVVP cable above 0.5 to connect them.

If the card reader is installed outside or in environment easy to

permeable, it is advisable to install a waterproof shield.

If you need to install several card readers, the distance among them

must over 30cm.

To reduce the noise in long distance transmission, the shield of cable

should connect to the GND of both controller and card reader

terminal.

Please take care of your card and report card loss in time when card is

lost.

If you require a higher security level, use multiple authentication

modes.

Multiple card types are supported. Please select an appropriate card

type according to the card performance and the usage scenarios.

DS-K1100 Series Card Reader

viii

Content Chapter 1 Introduction ........................................................... 1

1.1 Front View ..................................................................... 1 1.2 Rear View ...................................................................... 3 1.3 Slide View ...................................................................... 5

Chapter 2 Installation ............................................................. 7 2.1 Introduction for DIP Switch ........................................... 7 2.2 Definition of Cable ......................................................... 8 2.3 Wiring Cables ................................................................ 9 2.4 Installing Card Reader .................................................. 11

Chapter 3 Sound Prompt and Indicator ................................ 13

DS-K1100 Series Card Reader

1

Chapter 1 Introduction DS-K1100 series card reader is a kind of high-performance

product, with a 32 bit high-speed processor. It communicates with

access controller via either RS-485 protocol or Wiegand protocol.

And a build-in tamper-proof module helps to protect card reader

from malicious damage. As to the physical appearance, the

PC+ABS material makes water proof and dust proof possible in

poor environment.

1.1 Front View The front view of DS-K1101 series card reader is shown below:

Figure 1-1 DS-K1101MK Figure 1-2 DS-K1101M

DS-K1100 Series Card Reader

2

The front view of DS-K1102 series card reader is shown below:

Figure 1-3 DS-K1102MK Figure 1-4 DS-K1102M

The front view of DS-K1103 series card reader is shown below:

Figure 1-5 DS-K1103MK Figure 1-6 DS-K1103M

DS-K1100 Series Card Reader

3

The front view of DS-K1104 series card reader is shown below:

Figure 1-7 DS-K1104MK Figure 1-8 DS-K1104M

1.2 Rear View The rear view of card reader is shown below:

Figure 1-9 Rear View of DS-K1101 Series

DS-K1100 Series Card Reader

4

Figure 1-10 Rear View of DS-K1102 Series

Figure 1-11 Rear View of DS-K1103 Series

DS-K1100 Series Card Reader

5

Figure 1-12 Rear View of DS-K1104 Series

Table 1-1 Description of Rear View

No. Name

1 Cable Interface of RS-485, Power, LED Control, etc.

2 Buzzer

3 Tamper-proof Module

4 DIP Switch

1.3 Slide View The side view of card reader is shown below:

DS-K1100 Series Card Reader

6

Figure 1-13 DS-K1101 Series Figure 1-14 DS-K1102 Series

Figure 1-15 DS-K1103 Series Figure 1-16 DS-K1104 Series

DS-K1100 Series Card Reader

7

Chapter 2 Installation

2.1 Introduction for DIP Switch The DIP switch module is shown below. The No. of DIP switch

from left to right is 1 ~ 8.

Figure 2-1 DIP Switch Module

Table 2-1 Description of DIP Switch

Icon Description

Represent 1 in binary mode

Represent 0 in binary mode

For example, binary value of the following status is: 0000 1100.

Figure 2-2 DIP Switch Module

Table 2-2 Description of DIP Switch

No. Description DIP Switch Status

1 ~ 4 Address of RS-485 1: 1

0: 0

5 Card Security

Note: Only available when

1: Enable M1 card

encryption function,

DS-K1100 Series Card Reader

8

No. Description DIP Switch Status

Wiegand is enabled. For

DS-K1102E/EK, the DIP switch is

reserved.

and disable door

open via NFC card.

0: Disable M1 card

encryption function,

and enable door

open via NFC card.

6 Wiegand protocol or RS-485

protocol.

1: Wiegand protocol;

0: RS-485 protocol.

7 Wiegand Protocol

(available when No. 6 is 1)

1: Wiegand protocol

of 26-bit;

0: Wiegand protocol

of 34-bit.

8 Matched Resistance

(available for RS-485 protocol)

1: Enable;

0: Disable.

2.2 Definition of Cable The description of 10 cables is shown below.

Table 2-3 Description of Cable

Color Description

Yellow RS-485+

Brown Blue LED Control (available for Wiegand Protocol)

Blue RS-485-

Purple Beep Control (available for Wiegand Protocol)

Gray Case Sensor (available for Wiegand Protocol)

Green Wiegand W0 (available for Wiegand Protocol)

White Wiegand W1 (available for Wiegand Protocol)

Black GND

DS-K1100 Series Card Reader

9

Color Description

Orange Red LED Control (available for Wiegand Protocol)

Red PWR (DC +12V)

2.3 Wiring Cables Purpose:

Wire the cables between controller and card reader, thus to

establish the communication between them.

Steps for RS-485 communication mode:

1. Set the DIP switch of No. 6 as 0.

2. Set the DIP switch of No. 1 ~ 4 for RS-485 address. For

details, please refer to 2.1 Introduction for DIP Switch.

3. Wire the cable between controller and card reader as

shown below.

DS-K1100 Series Card Reader

10

Y e

llo w

B lu

e

B la

ck

R e

d

B la

ck

R e

d

G re

e n

W h

it e

P u

rp le

O ra

n ge

B ro

w n

Controller

Card Reader Figure 2-3 Wiring for RS-485 Communication Mode

Steps for Wiegand communication mode:

1. Set the DIP switch of No. 6 as 1.

2. Set the DIP switch of No. 5 and 7 for reading card mode and

Wiegand protocol. For details, please refer to 2.1

Introduction for DIP Switch.

3. Wiring the cable between controller and card reader as

shown below.

DS-K1100 Series Card Reader

11

Y e

llo w

B lu

e

B la

ck

R e

d

B la

ck

R e

d

G re

e n

W h

it e

P u

rp le

O ra

n ge

B ro

w n

Controller

Card Reader Figure 2-4 Wiring for Wiegand Communication Mode

2.4 Installing Card Reader Before you start:

Set the DIP switch. For details, refer to 2.1 Introduction for DIP

Switch.

Steps:

DS-K1100 Series Card Reader

12

1. Fix the plate on the wall or other

place. 1

2. Connect the cables between

controller and card reader. For

details, refer to 2.3 Wiring

Cables. 2

3

4

3. Push the card reader to match

the fixed plate.

4. Fasten the screw to keep the

components together.

DS-K1100 Series Card Reader

13

Chapter 3 Sound Prompt and

Indicator After the card reader is powered on, LED status indicator will turn

blue and flashing for 1 time. Then it will turn red and flashing for 3

times. At last the buzzer will send out a beep sound indicating the

starting up process is completed.

During using the card reader, it will send out different sounds

prompt and the LED indicator on it have different statuses. You

can refer to tables below for detailed information.

Table 3-1 Description of Prompt Sound

Sound Prompt Description

One beep

RS-485 protocol: Pressing keys prompt;

Swiping card prompt; Time out prompt for pressing keys or swiping card. Wiegand protocol: Pressing keys prompt; Swiping card prompt.

Two rapid beeps The operation of pressing keys or swiping card is valid.

Three slow beeps The operation of pressing keys or swiping card is invalid.

Rapidly continuous beeps

Alarm of tamper-proof.

Slowly continuous

beeps The card reader is unencrypted.

Eight rapid beeps The card (Mifare card) is cloned card.

Table 3-2 Description of LED Indicator

LED Indicator Status Description

Flashing green Card reader is working normally.

DS-K1100 Series Card Reader

14

LED Indicator Status Description

Solid green The operation of pressing keys or swiping card is valid.

Solid red The operation of pressing keys or swiping card is invalid.

Flashing red For RS-485 protocol: Registering failed or

card reader is offline.

020000001090312