Hikvision DS-PRI120 Radar Quick Start Guide PDF

1 of 1
1 of 1

Summary of Content for Hikvision DS-PRI120 Radar Quick Start Guide PDF

Security Radar

Diagram References

E N G L I S H

Indicator

Installation

For detailed settings, Scan the QR code to get the User Manual of Security Radar.

1. Download and install the iVMS-4200 client software. 2. Enter Control Panel - Modules Customization, select Radar, and click OK. 3. Enter Device Management page, select the radar in the Online Device List, click Modify Netinfo, change the port as 80, and click Add to Client. If the network of the radar is not the same as the PCs, click Add in the Device for Management list and enter the radar IP address in the pop-up window to add the radar.

4. In iVMS-4200 client software, enter Control Panel - Radar. 5. Upload Map: Select a map, draw a path on the map and set the plotting scale. 6. Expand the device group in the list on the left, and click and drag the radar onto the map. 7. Move along the edge of the required monitoring eld. Make sure the target sign (red arrow) is moving within the radar area (gray sector) shown on the added map. If the target sign is not within the sector, you need to adjust the mounting position or angle of the radar.

Power on the radar and make sure there is no large object in the monitoring area. Make the detector access into the internet.

Test the radar after installation to make sure it is properly mounted.

1. In iVMS-4200 client software, select the radar on Device Management page and click Remote Conguration to enter the conguration page.You can also enter the device IP address in the web browser to enter the conguration page. 2. Click Smart Rule Settings - Camera Linkage Settings. 3. Click + to add cameras to the radar. 4. Select a camera in the Camera IP Address List, and select the radar zone or the trigger line (or whole eld) in the Zone Linkage list or the Trigger Line List. 5. Add the camera to iVMS-4200 client software: In the client software, enter Device Management page, click Add in the Device for Management list, and enter the IP address, user name and password of the camera in the pop-up window.

1. Select a reference object about 50 m away from the speed dome. On the reference object, select a point whose altitude is the same as the speed domes. 2. Enter the IP address of the speed dome in the web browser to enter the web client. Adjust the PTZ buttons on the Live View page to make the reference object displayed in the image, and Click to zoom in the reference object. 3. Click , and click the reference point to middle the point in the frame. 4. Enter Conguration - PTZ - Initial Position, and click Set to set the initial position.

Link the camera to the Zone

Before calibration, set the initial position of the speed dome to ensure the tracking accuracy.

1. In iVMS-4200 client software, enter Radar page, click ... - Master-Slave Tracking Settings. 2. Double click the radar in the list on the left. Click the live view window of the speed dome needs to be calibrated, and click to maximum the window. 3. Select One Point Calibration as the calibration mode. 4. Ask the calibration sta to move in the radar detection eld. Click the track of the calibrate sta, and the color of the selected track will change from red to white. 5. Click Add to add a calibration point. 6. Ask the calibration sta to stand at the calibration point within 20 to 40 m directly in front of the radar.

7. Click the added calibration point in the list on the right to update the radar position of the calibration sta. 8. Adjust the PTZ buttons in the live view window to update the PTZ position: Click +/- to scale the calibration sta to a t size (The altitude of the calibration sta is about 2/3 of the altitude of the window), and adjust the PTZ to make the object align with the sign + at the center of the frame. (For precise alignment, click , and click on the center of the calibration sta.)

Calibrate the Speed Dome

Calibration

Initial Position settings

Enable Speed Dome Tracking In iVMS-4200 client software, enter the Master-Slave Tracking Settings page, select the live view window of the speed dome, and Check Enable Tracking.

Test

1

4

Wiring3

Formating2

5

Set Up6

Specification

1. Attach the mounting bracket on the detector with four supplied screws. 2. Loosen the screws on both sides of the bracket. 3. Adjust the angle of the detector. 4. Tighten the screws on the both sides of the bracket to complete the installation.

1. Attach the mounting bracket on the detector with four supplied screws. 2. Loosen the screws on both sides of the bracket. 3. Adjust the angle of the detector. 4. Tighten the screws on the both sides of the bracket to complete the installation.

a. Power Supply Indicator Solid Green: Detector Power on b. Fault Alarm Indicator Flashing Red: Fault Alarm Occurred, Solid Green: Alarm Restored c. Zone Alarm Indicator Solid Red: Zone Alarm Occurred, Solid Green: Alarm Restored d. Formating Indicator Red and green LED ashes 3 times: Formatting Successfully

a. Alarm Output Wiring (Dry Contact Output) a1: one for electrical load a2: three for electronic load b. Alarm Input Wiring (Reserved) c. DC Power Supply Wiring d. Ethernet (PoE port) Wiring e. Grounding

Loosen the screws on the rear cover to remove the cover. Hold the Reset button while powering the radar on until the red and green LED ashes 3 times.

Ceiling Mounting

Pole Mounting

Before You Start: The recommended installation height is 2.5 m. Make sure that the mounting surface is strong enough to withstand at least 50N, as well as four times the weight of the device and the bracket.

1. In iVMS-4200 client software, enter Control Panel - Radar. 2. Click ... - Draw Zone Manually or Draw Trigger Line, and click the mouse to draw a zone or trigger line on the radar detection area. 3. Set the parameters of the zone or trigger line. Zone: edit the zone parameters in the pop-up window. Click OK to nish the settings. Trigger Line: set the direction of the line (left to right, right to left, or both way).Click Cancel to nish the settings.

Add Zone or Trigger Line for the Detector

If the speed dome is installed together with the radar, select the calibration mode as One Point Calibration. Otherwise, set the calibration as Multi-point Calibration. For one point calibration, you can refer to the following steps, and see user manual for multi-point calibration.

Note: You should activate the device for the rst usage. Select the device in the Online Device List, click Activate, create a password to activate the device. Scan the QR code to get the User Manual of Security Radar.

Note: The trigger line is not allowed to be crossed .

Before the operation, you need to click the - on the Radar page or right click the selected radar and select disarm to disarm the radar.

1

1

2

2

3

4

Use only power supply listed below: Manufacturer: Shenzhen HONOR Electronic Co., Ltd. ModelADS-26FSG-12 12024EPG

COPYRIGHT 2019 Hangzhou Hikvision Digital Technology Co., Ltd. ALL RIGHTS RESERVED. Any and all information, including, among others, wordings, pictures, graphs are the properties of Hangzhou Hikvision Digital Technology Co., Ltd. or its subsidiaries (hereinafter referred to be Hikvision). This user manual (hereinafter referred to be the Manual) cannot be reproduced, changed, translated, or distributed, partially or wholly, by any means, without the prior written permission of Hikvision. Unless otherwise stipulated, Hikvision does not make any warranties, guarantees or representations, express or implied, regarding to the Manual.

About this Manual This Manual is applicable to the Security Radar. The Manual includes instructions for using and managing the product. Pictures, charts, images and all other information hereinafter are for description and explanation only. The information contained in the Manual is subject to change, without notice, due to rmware updates or other reasons. Please nd the latest version in the company website (http://overseas.hikvision.com/en/). Please use this user manual under the guidance of professionals.

Trademarks Acknowledgement and other Hikvisions trademarks and logos are the properties of Hikvision in various jurisdictions. Other trademarks and logos mentioned below are the properties of their respective owners.

Product Information

This product and - if applicable - the supplied accessories too are marked with "CE" and comply therefore with the applicable harmonized European standards listed under the RE Directive 2014/53/EU, the EMC Directive 2014/30/EU, the LVD Directive 2014/35/EU, the RoHS Directive 2011/65/EU.

2012/19/EU (WEEE directive): Products marked with this symbol cannot be disposed of as unsorted municipal waste in the European Union. For proper recycling, return this product to your local supplier upon the purchase of equivalent new equipment, or dispose of it at designated collection points. For more information see: www.recyclethis.info

2006/66/EC (battery directive): This product contains a battery that cannot be disposed of as unsorted municipal waste in the European Union. See the product documentation for specic battery information. The battery is marked with this symbol, which may include lettering to indicate cadmium (Cd), lead (Pb), or mercury (Hg). For proper recycling, return the battery to your supplier or to a designated collection point. For more information see:www.recyclethis.info

This product operates in a European non-harmonised frequency band.

1 3

4

6

206.5

22 8.

5

60.8

2 a

b

c

d

NC NO

N O

C O

M N

C

N O

C O

M N

C

a 1

2a

b

c

d

OSD

1

3

1 2

50 m

09-29-2018 16:50:20

+

+

3D

3D

09-29-2018 16:51:22

09-29-2018 16:51:22

+

H H=h h

Initial Position

09-29-2018 16:52:07

a b

NO4

NC4 COM4

NO3

NC3 COM3

NO2

NC2 COM2

NO1

NC1 COM1

e

Product Security Radar Detection Range Vehicle:150 m, Human:120 m Horizontal Angle 120

Max. Target Number 64

Zone 16 Trigger Line 4 Velocity Range -9.8 to 9.8 m/s Range Measurement Accuracy

0.75 m

Velocity Measurement Accuracy

0.1 m/s

Angle Measurement Accuracy

1

3-ch weak current output: 0.5 A/125 VAC,breakdown voltage: 1 KV 1-ch strong current output: 10 A/240 VAC,breakdown voltage: 2.5 KV

Alarm Output

Netowrk Interface 1 RJ45 10M/100M self-adaptive, supports POE

Communication Protocol

Standard ISAPI protocol, NAL2300 protocol HTTP, DNS, NTP, TCP, UDP, DHCP, ARP, and SSH

Exception Detection Tampering alarm Moving alarm

Power Interface 802.3at standard POE or 12 VDC The supplied power adapter is for 12 VDC power input.

Operation Temperature 40 to 65 Operation Humidity 10% to 90% Dimension(W x H x D) 206*228*61 mm Protection level IP67, IK09, NEMA 4X Weight 1.9 kg

Installation

Bracket installation Installation Height: 1.2 m to 4 m Recommended height range: 2.5 m Recommended vertical angle: 0

OSD

!

!!

1 (-24.29,42) (12,25,34)

1 (-19.79,34) (31,43,17)

a

b

Note: The track disappears if the calibration sta is standing in place for more than 7 s. If the calibration sta does not move to the calibration point when the track disappears, you need to ask the calibration sta moves again, and click the track of the calibration sta to continue the calibration.

Before the operation, you need to disable the parking function, and set the initial position of the speed dome.

FCC Information Please take attention that changes or modication not expressly approved by the party responsible for compliance could void the users authority to operate the equipment. FCC compliance: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment o and on, the user is encouraged to try to correct the interference by one or more of the following measures: Reorient or relocate the receiving antenna. Increase the separation between the equipment and receiver. Connect the equipment into an outlet on a circuit dierent from that to which the receiver is connected. Consult the dealer or an experienced radio/TV technician for help. This equipment should be installed and operated with a minimum distance 20cm between the radiator and your body. FCC Conditions This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: 1. This device may not cause harmful interference. 2. This device must accept any interference received, including interference that may cause undesired operation.

IC Information Industry Canada ICES-003 Compliance This device meets the CAN ICES-3 (B)/NMB-3(B) standards requirements. Industry Canada ICES-003 Compliance This device meets the CAN ICES-3 (B)/NMB-3(B) standards requirements.

This device complies with Industry Canada licence-exempt RSS standard(s). Operation is subject to the following two conditions: (1) this device may not cause interference, and (2) this device must accept any interference, including interference that may cause undesired operation of the device. Le prsent appareil est conforme aux CNR d'Industrie Canada applicables aux appareils radioexempts de licence. L'exploitation est autorise aux deux conditions suivantes : (1) l'appareil ne doit pas produire de brouillage, et (2) l'utilisateur de l'appareil doit accepter tout brouillage radiolectrique subi, mme si le brouillage est susceptible d'en compromettre le fonctionnement. Under Industry Canada regulations, this radio transmitter may only operate using an antenna of a type and maximum (or lesser) gain approved for the transmitter by Industry Canada. To reduce potential radio interference to other users, the antenna type and its gain should be so chosen that the equivalent isotropically radiated power (e.i.r.p.) is not more than that necessary for successful communication.

Conformment la rglementation d'Industrie Canada, le prsent metteur radio peut fonctionner avec une antenne d'un type et d'un gain maximal (ou infrieur) approuv pour l'metteur par Industrie Canada. Dans le but de rduire les risques de brouillage radiolectrique l'intention des autres utilisateurs, il faut choisir le type d'antenne et son gain de sorte que la puissance isotrope rayonne quivalente (p.i.r.e.) ne dpasse pas l'intensit ncessaire l'tablissement d'une communication satisfaisante.

This equipment should be installed and operated with a minimum distance 20cm between the radiator and you

Manualsnet FAQs

If you want to find out how the DS-PRI120 Hikvision works, you can view and download the Hikvision DS-PRI120 Radar Quick Start Guide on the Manualsnet website.

Yes, we have the Quick Start Guide for Hikvision DS-PRI120 as well as other Hikvision manuals. All you need to do is to use our search bar and find the user manual that you are looking for.

The Quick Start Guide should include all the details that are needed to use a Hikvision DS-PRI120. Full manuals and user guide PDFs can be downloaded from Manualsnet.com.

The best way to navigate the Hikvision DS-PRI120 Radar Quick Start Guide is by checking the Table of Contents at the top of the page where available. This allows you to navigate a manual by jumping to the section you are looking for.

This Hikvision DS-PRI120 Radar Quick Start Guide consists of sections like Table of Contents, to name a few. For easier navigation, use the Table of Contents in the upper left corner.

You can download Hikvision DS-PRI120 Radar Quick Start Guide free of charge simply by clicking the “download” button in the upper right corner of any manuals page. This feature allows you to download any manual in a couple of seconds and is generally in PDF format. You can also save a manual for later by adding it to your saved documents in the user profile.

To be able to print Hikvision DS-PRI120 Radar Quick Start Guide, simply download the document to your computer. Once downloaded, open the PDF file and print the Hikvision DS-PRI120 Radar Quick Start Guide as you would any other document. This can usually be achieved by clicking on “File” and then “Print” from the menu bar.