Hikvision DS-PEA102Y Panel User's Manual PDF

1 of 57
1 of 57

Summary of Content for Hikvision DS-PEA102Y Panel User's Manual PDF

Panic Alarm Station User Manual

Panic Alarm Station User Manual

i

Legal Information

2022 Hangzhou Hikvision Digital Technology Co., Ltd. All rights reserved.

About this Manual

The Manual includes instructions for using and managing the Product. Pictures, charts, images and all other information

hereinafter are for description and explanation only. The information contained in the Manual is subject to change,

without notice, due to firmware updates or other reasons. Please find the latest version of this Manual at the Hikvision

website (https://www.hikvision.com/).

Please use this Manual with the guidance and assistance of professionals trained in supporting the Product.

Trademarks

and other Hikvisions trademarks and logos are the properties of Hikvision in various jurisdictions.

Other trademarks and logos mentioned are the properties of their respective owners.

Disclaimer

TO THE MAXIMUM EXTENT PERMITTED BY APPLICABLE LAW, THIS MANUAL AND THE PRODUCT DESCRIBED, WITH ITS

HARDWARE, SOFTWARE AND FIRMWARE, ARE PROVIDED AS IS AND WITH ALL FAULTS AND ERRORS. HIKVISION

MAKES NO WARRANTIES, EXPRESS OR IMPLIED, INCLUDING WITHOUT LIMITATION, MERCHANTABILITY, SATISFACTORY

QUALITY, OR FITNESS FOR A PARTICULAR PURPOSE. THE USE OF THE PRODUCT BY YOU IS AT YOUR OWN RISK. IN NO

EVENT WILL HIKVISION BE LIABLE TO YOU FOR ANY SPECIAL, CONSEQUENTIAL, INCIDENTAL, OR INDIRECT DAMAGES,

INCLUDING, AMONG OTHERS, DAMAGES FOR LOSS OF BUSINESS PROFITS, BUSINESS INTERRUPTION, OR LOSS OF DATA,

CORRUPTION OF SYSTEMS, OR LOSS OF DOCUMENTATION, WHETHER BASED ON BREACH OF CONTRACT, TORT

(INCLUDING NEGLIGENCE), PRODUCT LIABILITY, OR OTHERWISE, IN CONNECTION WITH THE USE OF THE PRODUCT,

EVEN IF HIKVISION HAS BEEN ADVISED OF THE POSSIBILITY OF SUCH DAMAGES OR LOSS.

YOU ACKNOWLEDGE THAT THE NATURE OF THE INTERNET PROVIDES FOR INHERENT SECURITY RISKS, AND HIKVISION

SHALL NOT TAKE ANY RESPONSIBILITIES FOR ABNORMAL OPERATION, PRIVACY LEAKAGE OR OTHER DAMAGES

RESULTING FROM CYBER-ATTACK, HACKER ATTACK, VIRUS INFECTION, OR OTHER INTERNET SECURITY RISKS; HOWEVER,

HIKVISION WILL PROVIDE TIMELY TECHNICAL SUPPORT IF REQUIRED.

YOU AGREE TO USE THIS PRODUCT IN COMPLIANCE WITH ALL APPLICABLE LAWS, AND YOU ARE SOLELY RESPONSIBLE

FOR ENSURING THAT YOUR USE CONFORMS TO THE APPLICABLE LAW. ESPECIALLY, YOU ARE RESPONSIBLE, FOR USING

THIS PRODUCT IN A MANNER THAT DOES NOT INFRINGE ON THE RIGHTS OF THIRD PARTIES, INCLUDING WITHOUT

LIMITATION, RIGHTS OF PUBLICITY, INTELLECTUAL PROPERTY RIGHTS, OR DATA PROTECTION AND OTHER PRIVACY

RIGHTS. YOU SHALL NOT USE THIS PRODUCT FOR ILLEGAL HUNTING ANIMALS, INVASION OF PRIVACY OR ANY OTHER

PURPOSE WHICH IS ILLEGAL OR DETRIMENTAL TO THE PUBLIC INTEREST. YOU SHALL NOT USE THIS PRODUCT FOR ANY

PROHIBITED END-USES, INCLUDING THE DEVELOPMENT OR PRODUCTION OF WEAPONS OF MASS DESTRUCTION, THE

DEVELOPMENT OR PRODUCTION OF CHEMICAL OR BIOLOGICAL WEAPONS, ANY ACTIVITIES IN THE CONTEXT RELATED

TO ANY NUCLEAR EXPLOSIVE OR UNSAFE NUCLEAR FUEL-CYCLE, OR IN SUPPORT OF HUMAN RIGHTS ABUSES. IN THE EVENT OF ANY CONFLICTS BETWEEN THIS MANUAL AND THE APPLICABLE LAW, THE LATER PREVAILS.

Panic Alarm Station User Manual

ii

Regulatory Information

FCC Information

Please take attention that changes or modification not expressly approved by the party responsible for compliance could void the users authority to operate the equipment.

FCC Compliance: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

Reorient or relocate the receiving antenna.

Increase the separation between the equipment and receiver.

Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.

Consult the dealer or an experienced radio/TV technician for help

FCC Conditions

This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions:

1. This device may not cause harmful interference.

2. This device must accept any interference received, including interference that may cause undesired operation.

EU Conformity Statement

This product and - if applicable - the supplied accessories too are marked with "CE" and comply therefore with the applicable harmonized European standards listed under the EMC Directive 2014/30/EU, LVD Directive 2014/35/EU, the RoHS Directive 2011/65/EU.

2012/19/EU (WEEE directive): Products marked with this symbol cannot be disposed of as unsorted municipal waste in the European Union. For proper recycling, return this product to your local supplier upon the purchase of equivalent new equipment, or

dispose of it at designated collection points. For more information see: www.recyclethis.info

2006/66/EC (battery directive): This product contains a battery that cannot be disposed of as unsorted municipal waste in the European Union. See the product documentation for specific battery information. The battery is marked with this symbol, which may

include lettering to indicate cadmium (Cd), lead (Pb), or mercury (Hg). For proper recycling, return

Panic Alarm Station User Manual

iii

the battery to your supplier or to a designated collection point. For more information see: www.recyclethis.info

Industry Canada ICES-003 Compliance

This device meets the CAN ICES-3 (A)/NMB-3(A) standards requirements.

Panic Alarm Station User Manual

iv

Applicable Models

This manual is applicable to the models listed in the following table.

Product Model

Panic Alarm Station DS-PEA102S DS-PEA102R DS-PEA102Y

Symbol Conventions

The symbols that may be found in this document are defined as follows.

Safety Instruction

The device should be used in compliance with local laws and electrical safety regulations. Refer to the appropriate documentation for detailed information.

The input voltage should conform to IEC60950-1 standard: SELV (Safety Extra Low Voltage) and the

Limited Power Source (100120/200240 VAC). Refer to the appropriate documentation for detailed information.

DO NOT connect multiple devices to one power adapter, to avoid over-heating or fire hazards caused by overload.

Make sure the plug is properly connected to the power socket.

If smoke, odor, or noise arises from the device, immediately turn off the power, unplug the power cable, and contact the service center.

Do not drop the device or subject it to physical shock.

Wipe the device gently with a clean cloth and a small quantity of ethanol, if necessary.

Do not aim the lens at the sun or any other bright light.

When any laser equipment is in use, make sure that the device lens is not exposed to the laser beam, or it may burn out.

Symbol Description

Provides additional information to emphasize or supplement important points of the main text.

Indicates a potentially hazardous situation, which if not avoided, could result in equipment damage, data loss, performance degradation, or unexpected results.

Indicates a hazard with a high level of risk, which if not avoided, will result in death or serious injury.

Panic Alarm Station User Manual

v

Do not expose the device to high electromagnetic radiation or extremely hot, cold, dusty, or damp

environments, the appropriate temperature is -25 to 55.

Place the device in a dry and well-ventilated environment.

Keep non-waterproof devices away from liquids.

Keep the device in original or similar packaging while transporting it.

A few device components (e.g., electrolytic capacitor) require regular replacement. The average lifespan varies, so periodic checking is recommended. Contact your dealer for details.

Improper use or replacement of the battery may result in explosion hazard. Replace with the same or equivalent type only. Dispose of used batteries in conformance with the instructions provided by the battery manufacturer.

Never attempt to disassemble the device.

Serial Port Accessing

While accessing with serial port, enter 'debug' and then the system will print a string. Enter the string in the

URL of http://psh.hikvision.com.cn:8080/sso/home/page to get the terminal control command. Insert

the command to access to the device serial port.

Panic Alarm Station User Manual

vi

Table of Content

Chapter 1 Overview ........................................................................................................................ 1

Description .......................................................................................................................... 1

Key Features ........................................................................................................................ 1

Chapter 2 Activation ....................................................................................................................... 2

Activate via SADP ................................................................................................................. 2

Activate Device via Client Software ...................................................................................... 3

Chapter 3 Remote Settings ........................................................................................................... 18

Device Management .......................................................................................................... 18

3.1.1 Add Device to the Client Software ............................................................................. 18

3.1.2 Edit Network Parameters .......................................................................................... 19

Network Configuration ...................................................................................................... 19

3.2.1 Set General Network Parameters .............................................................................. 19

3.2.2 Set DNS ..................................................................................................................... 21

3.2.3 Set NAT ..................................................................................................................... 21

3.2.4 Set SIP ....................................................................................................................... 23

3.2.5 Set Hik-Connect ........................................................................................................ 23

3.2.6 Access the Platform .................................................................................................. 24

3.2.7 Set Alarm Center ....................................................................................................... 25

Alarm Settings ................................................................................................................... 27

3.3.1 Set Zone .................................................................................................................... 27

3.3.2 Set Relay ................................................................................................................... 29

3.3.3 Set Call Waiting ......................................................................................................... 30

3.3.4 Set Voice Prompt ...................................................................................................... 30

Alarm Management ........................................................................................................... 32

3.4.1 Manage Relay ........................................................................................................... 32

3.4.2 Manage Audio Input/Output ..................................................................................... 32

3.4.3 Manage Audio File .................................................................................................... 33

Video & Audio Settings ...................................................................................................... 35

3.5.1 Video & Audio Settings ............................................................................................. 35

3.5.2 Set Display ................................................................................................................ 36

3.5.3 Set Image Parameters ............................................................................................... 38

3.5.4 Set Intercom Audio ................................................................................................... 38

System Settings ................................................................................................................. 39

3.6.1 Set Time .................................................................................................................... 39

3.6.2 Set System Parameters .............................................................................................. 39

3.6.3 Set Security ............................................................................................................... 40

3.6.4 Set Password ............................................................................................................. 40

3.6.5 Set User .................................................................................................................... 41

Panic Alarm Station User Manual

vii

3.6.6 Search for Log ........................................................................................................... 42

3.6.7 Security Audit Log ..................................................................................................... 43

3.6.8 Maintain the System ................................................................................................. 44

3.6.9 View Device Information ........................................................................................... 45

3.6.10 View Device Information ......................................................................................... 46

Check Status ...................................................................................................................... 47

3.7.1 Check Zone Status ..................................................................................................... 47

3.7.2 Check Relay Status .................................................................................................... 47

Other Settings.................................................................................................................... 47

3.8.1 Set Auxiliary Output .................................................................................................. 47

Chapter 4 Web Client Settings ...................................................................................................... 48

Live View ........................................................................................................................... 48

Configuration ..................................................................................................................... 48

4.2.1 System ...................................................................................................................... 48

4.2.2 Network .................................................................................................................... 49

4.2.3 Video/Audio .............................................................................................................. 52

4.2.4 Image ........................................................................................................................ 54

4.2.5 Device ....................................................................................................................... 55

4.2.6 Two-way Audio Settings ............................................................................................ 57

4.2.7 Custom ..................................................................................................................... 58

Maintenance and Security ................................................................................................. 59

4.3.1 Maintenance ............................................................................................................. 59

4.3.2 Security ..................................................................................................................... 60

Chapter 5 Communication Matrix and Device Command............................................................. 62

Panic Alarm Station User Manual

1

Chapter 1 Overview

Description

DS-PEA102 series of panic alarm station supports two-way audio communication, and panic alarm, which realize alarm aid in emergency.

The product is applied in school, hospital, metro, scenic area, prison, etc.

Key Features

Network adaptive and video and audio adaptive

Built-in omnidirectional microphone

Supports two-way audio communication and configuration

Supports listening and broadcast

Multiple network protocols including TCP/IP and RTSP

Supports Standard SIP, ISUP, and HIK-Connect

Protection level: IP54

Anti-Explosion level: IK08

Supports external siren and strobe light

Panic Alarm Station User Manual

2

Chapter 2 Activation

In order to protect personal security and privacy and improve the network security level, you should activate the device the first time you connect the device to a network.

Activate via SADP

SADP is a tool to detect, activate and modify the IP address of the device over the LAN.

Before You Start

Get the SADP software from the supplied disk or the official website http://www.hikvision.com/en/, and install the SADP according to the prompts.

The device and the PC that runs the SADP tool should be within the same subnet.

The following steps show how to activate a device and modify its IP address. For batch activation and IP addresses modification, refer to User Manual of SADP for details.

Steps

1. Run the SADP software and search the online devices.

2. Find and select your device in online device list.

3. Input new password (admin password) and confirm the password.

STRONG PASSWORD RECOMMENDED-We highly recommend you create a strong password of your own choosing (using a minimum of 8 characters, including upper case letters, lower case letters, numbers, and special characters) in order to increase the security of your product. And we recommend you reset your password regularly, especially in the high security system, resetting the password monthly or weekly can better protect your product.

4. Click Activate to start activation.

Activate via SADP

Panic Alarm Station User Manual

3

Status of the device becomes Active after successful activation.

5. Modify IP address of the device.

1) Select the device.

2) Change the device IP address to the same subnet as your computer by either modifying the IP address manually or checking Enable DHCP.

3) Input the admin password and click Modify to activate your IP address modification.

Activate Device via Client Software

Before You Start

Get the iVMS-4200 client software from the supplied disk or the official website http://www.hikvision.com/en/. Install the software by following the prompts.

The device and the PC that runs the software should be in the same subnet.

Steps

1. Run the client software.

2. Enter Device Management Device in the Maintenance and Management list.

3. Click Online Device.

4. Check the device status from the online device list, and select an inactive device.

5. Click Activate.

6. Create and confirm the admin password of the device.

STRONG PASSWORD RECOMMENDED-We highly recommend you create a strong password of your own choosing (using a minimum of 8 characters, including upper case letters, lower case letters, numbers, and special characters) in order to increase the security of your product. And we recommend you reset your password regularly, especially in the high security system, resetting the password monthly or weekly can better protect your product.

7. Click OK to start activation.

Device status will change to Active after successful activation.

8. Edit IP address of the device.

1) Select a device and click on the online device list.

2) Change the device IP address to the same subnet with your computer.

3) Enter the admin password of the device and click OK to complete modification.

9. Optional: Check the device on the online device list and click Add to add the device to the device list.

Panic Alarm Station User Manual

18

Chapter 3 Remote Settings

In the client software, go to Device Management, click and select the device in the device list, and

click to enter the Remote Configuration page.

Note

The device should be activated the first time it is used to log in and use properly. See Activation to activate the device.

You need to add the device to the client software before configure it. See Add Device via Client Software.

Get the client software from the technical support, and install the software according to the prompts.

Device Management

Before You Start

Activate the device and ensure that the device is on the same subnet as the PC.

Client Software Main Page

In the client software, go to Device Management Device on the Maintenance and Management list. You can add devices to client software by several methods on the device

Panic Alarm Station User Manual

19

management page. The following describes how to add devices through IP/Domain Name. For more information, see iVMS-4200 Client Software User Manual.

Steps

1. On the Device page, click Add.

2. Select IP/Domain as the adding mode, edit the device information, including Name, Address, Port, User Name, and Password.

3. Click Add to add the device.

Edit the device network parameters so that the device IP address is in the same subnet as the computer IP address.

You can edit the network parameters through the SADP software, or the client software. The SADP software is taken as an example for explanation.

Steps

1. Run the SADP software, check the activated device, and edit the IP Address, Subnet Mask, Gateway and other parameters in the Modify Network Parameters list on the right.

If check Enable DHCP, the device can automatically obtain network parameters.

2. Enter the activation password, click Modify, and the prompt Modify parameters is successful indicate that the settings take effect.

Network Configuration

Configure network mode, IP address, NIC and NIC type, subnet mask, gateway, MAC address, MTU settings, and port No. for device.

Before You Start

Make sure the cable of the device is connected.

Steps

1. Click to enter the Remote Configuration page, go to Network General.

Panic Alarm Station User Manual

20

Network Basic Settings Page

2. Select the NIC type.

3. Set the network address.

Automatically obtain the network address

Check Auto-obtain, the device automatically obtains the network address (IPv4 Address, Subnet Mask (IPv4), Default Gateway (IPv4)) through DHCP.

Manually set the network address

According to the actual network environment, manually set the network address IPv4 Address, Subnet Mask (IPv4), Gateway Address (IPv4).

4. Set the MTU(Byte), Device Port, HTTP port, and RTSP port for the device.

MTU(Byte) Maximum transmission unit, which refers to the maximum packet size passed by TCP/UDP protocol network transmission. The default is 1500.

Device Port The default device port number is 8000.

HTTP port The default port number is 80, and it can be changed to any port No. which is not occupied.

RTSP port The default port number is 554 and it can be changed to any port No. ranges from 1 to 65535.

5. Click Save to save the settings.

Panic Alarm Station User Manual

21

When the device accesses the network through the domain name, you need to configure the correct and available DNS server IP address.

The device supports 2 DNS address.

Click to enter the Remote Configuration page, go to Network DNS, set the DNS server IP address and click Save to save the settings.

DNS Setting Page

When DHCP is enabled, the DNS cannot be set.

Enable the UPnP function, and you don't need to configure the port mapping for each port, and the device is connected to the Wide Area Network via the router.

Steps

Universal Plug and Play (UPnP) is a networking architecture that provides compatibility among networking equipment, software and other hardware devices. The UPnP protocol allows devices to connect seamlessly and to simplify the implementation of networks in the home and corporate environments.

1. Click to enter the Remote Configuration page, go to Network NAT.

Panic Alarm Station User Manual

22

NAT Setting Page

2. Check Enable UPnP, and set Mapping Types as Manual or Auto.

Set Mapping Types as Auto

The Ports are read-only, and the external ports are set by the router automatically.

Set Mapping Types as Manual

You can edit the external port on your demand. And then you should enable UPnP function on the router.

Please do not arbitrarily edit the default port number. If there is a port conflict and you need to edit the port number, please modify the port number as follows.

HTTP Port By default, the value of the HTTP port No. is 80.

Server Port By default, the value of the Server port No. is 8000. If the value is changed, you need to enter the server port number on the login page when you log in the device by client software.

RTSP Port Real-time transport protocol port, please make sure that the port you modified is available. By default, the value of the RTSP port No. is 554.

3. Click Save to save the settings.

Panic Alarm Station User Manual

23

After the SIP server address is set, the device actively registers to the SIP server, and devices under the same SIP server address can communicate with each other.

Steps

1. Click to enter the Remote Configuration page, go to Network SIP Settings.

SIP Settings Page (Private Protocol & SIP Protocol)

2. Check Enable box to enbale the Sip server.

3. Enter the Sip server parameters.

The server port No. ranges from 1024 to 65535.

The device ID ranges from 0 to 999999.

The characters of local No. should be 1 to 64.

The login cycle ranges from 1 to 30 (min)

4. Click Save.

Enable Hik-Connect service and you can add the device to Hik-Connect.

Steps

1. Click to enter the Remote Configuration page, go to Network Configuring the Hik- Connect Settings.

Panic Alarm Station User Manual

24

Hik-Connect Service Setting Page

2. Check Enable Hik-Connect Access andenter the verification code to enable Hik-Connect service. 3. Optional: If you want to edit Server Address, check Custom and enter the server address.

Note

The default server address is litedev.hik-connect.com.

4. Select Network Mode. 5. Enter a verification code and click Generate QR code.

There will be a QR code displaying on the page. 6. Click Save. 7. Scan the QR code via Hik-Connect and the device will be added to Hik-Connect.

Platform access provides you an option to manage the devices via platform.

Steps

1. Click to enter the Remote Configuration page, go to Network Platform Access.

Panic Alarm Station User Manual

25

Platform Access Configuration

2. Check Enable Platform Access to enable the Platform Access function.

3. Set the platform access parameters.

Access Type

Select the platform to be accessed.

Server IP or Domain Name

Enter the IP address or domain name of the platform.

Access to Server Port

Enter the port number of the platform.

Panel ID

Panel ID is the unique identification of the device.

Communication Network

Select the network mode for communication with platform.

Registration Status

Display the status which the device registers to the platform.

4. Click Save, and you can access to the device via platform.

Configure the alarm center. When an alarm is triggered, the alarm information can be uploaded to the configured alarm center.

Steps

1. Click to enter the Remote Configuration page, go to Network Network Center Settings.

Panic Alarm Station User Manual

26

Network Center Settings

2. Select a NIC.

The device supports two wired networks and one wireless network. Each network supports uploading alarm information to one alarm center.

3. Check Enable Upload Center to enable the alarm center, and set the upload center parameters.

Notify Surveillance Center Each NIC supports only one upload center, and the default is Net Center 1.

Server Mode The address type of the upload center server. You can set Server Type as IP4/IP6 or Domain Name.

IP Address/Server Domain Name Enter the server IP address or server domain name according to the server type you set.

Port No. The port number of the upload center. The HIK protocol defaults to 7200.

Protocol Type The default is HIK.

User Name Supports numbers and letters. The HIK protocol can be set to a length ranging from 6 to 9 digits.

If you set the protocol type as HIK, you do not need to edit the user name.

4. Click Save.

Panic Alarm Station User Manual

27

Alarm Settings

The device supports four alarm input zones and two default zones (emergency call help and consulting). You need to configure zone parameters.

Steps

The default zone has a default zone type, default audio file, and the default zone will automatically upload an alarm recovery report. These three parameters (Zone Type, Audio File and Upload Alarm Recovery Report) do not need to be set.

1. In the client software, go to Device Management, select the device in the device list, and click

to enter the Remote Configuration page.

2. Go to Input Settings Zone.

Zone

3. Select an zone, click .

Panic Alarm Station User Manual

28

Set Zone

4. Set zone parameters.

Name Zone name.

Detector Type The detector type of the zone.

Zone Type Four zone type can be set for Non-default zones: Instant Zone, Fire Zone, 24-hour Non-voiced Zone, Shield Zone.

Instant Zone In the armed state, as long as the detector connected to the zone is triggered, an alarm is generated immediately without delay.

Fire Zone The fire zone must be set to a 24-hour alarm zone. When the fire zone is triggered, start the external siren/sounder.

24-hour Non-voiced Zone The detector working in 24-hour non-voiced zone is in an alert state for 24 hours, and will not be affected by the disarming operation. Once triggered, the information is immediately uploaded to the center with no alarm sound.

Shield Zone No events will trigger an alarm.

Sensitivity The default value is 500 ms.

Audio File

Panic Alarm Station User Manual

29

Select an audio file for zone. Upload Alarm Recovery Report

If check Upload Alarm Recovery Report, the report will be uploaded to the center when the alarm is restored.

5. Select the zone linkage.

Linked Trigger After the zone is triggered, the selected alarm output is on.

Channel After the zone is triggered, the selected video channel is linked.

6. Optional: Click Copy to..., copy the zone parameter configuration to other zones.

7. Click Save.

Configure the relay parameters, include the relay name and the output delays.

Steps

1. Click to enter the Remote Configuration page, go to Output Settings Relay. 2. Select a relay and click , set the relay parameters.

Relay Configuration Page

Name

The relay name.

Panic Alarm Station User Manual

30

Output Delay(s)

The output delay time, can be set from 0 to 2000s. After the zone event is triggered, the relay will turn off the relay output after the output delay time is ended.

3. Click Save. 4. Optional: Click Copy to..., you can copy the relay settings to other relays.

Configure the call waiting parameters, include the maximum ring duration and waiting time.

Steps

1. Click to enter the Remote Configuration page, go to Output Settings Waiting.

Call Waiting Settings Page

2. Set the call waiting parameters.

Calling Duration The playback time of the calling tone when calling, can be set from 40 s to 80 s.

Waiting Time The extended playback time of the prompt tone based on the maximum ring time when calling the center station and pressing the call waiting button, can b set from 10 seconds to 60 s.

3. Click Save.

Steps

1. Click to enter the Remote Configuration page, go to Output Settings Voice Prompt.

Panic Alarm Station User Manual

31

Voice Prompt Configuration Page

2. Set the Center Busy File, Refuse Prompt, Voice Talk Ending Prompt, and Panic Alarm Prompt Sound.

3. Optional: Configure the mute program.

1) Check Enable to enable the mute program.

2) Click and drag the mouse on the time bar to draw the scheduled time period.

3) 3Optional: Edit the time period.

Modify the time period

Click and select the added time period, drag to modify the time period position; click and select the added time period, then moves the cursor to both ends of the time period, when the cursor becomes a double arrow, you can drag the mouse left and right to modify the time period.

Delete one time period

Click and select the time period, and click Delete to delete the selected time period.

Delete all time periods

Click Clear to delete all time periods. The device will be muted during the configured time period.

4. Click Save.

Panic Alarm Station User Manual

32

Alarm Management

Open or close the relay via client software.

Click to enter the Remote Configuration page, go to Alarm Management Relay

Relay

Check the relays that need to be turned on/off. Click Enable/Locked to change the relay switch status. Click Refresh, you can refresh the relay switch status.

Configure the audio input/audio output mode and the volume of the corresponding mode.

Steps

1. Click to enter the Remote Configuration page, go to Alarm Management Audio In/Out.

Panic Alarm Station User Manual

33

Audio Input/Output

2. Set the audio input/output mode and volume.

spkOut is the device's own audio input/output.

3. Click Save.

Upload the custom audio files to SD card, and delete the audio file in the SD card.

Before You Start

Insert the SD card into the device.

Steps

1. Click to enter the Remote Configuration page, go to Alarm Management Audio File.

Panic Alarm Station User Manual

34

Audio File Management

2. Upload the custom audio files. 1) Click View to select the audio file (can be selected in batch). 2) Check the audio file in the Upload File list and click Upload.

Note

Supported Audio file format: .mp3 and .wav (8 kHz, 16 bit, and single track). The file name can't contain spaces at the beginning and end. The length of the file name should be not more than 31, and the file name cannot contain symbols: ?\/*<>|. Each audio file size up to 2MB, and up to 16 audio files are uploaded. An audio file will be overwritten if uploading an audio file with the same name.

3. Optional: Delete the audio files in the SD card. 1) In the File List, click Refresh to display the audio files. 2) Check the audio file needs to be deleted, click Delete.

The function using the deleted audio files will restore the default audio file configuration.

Panic Alarm Station User Manual

35

Video & Audio Settings

Configure the image quality, resolution and other parameters of the camera.

Click to enter the Remote Configuration page, click Image Video & Audio.

Video & Audio

Select a camera, and set the video and audio parameters. Click Save to save the settings.

You can click Copy to... to copy the parameters to other camera.

After editing the video and audio parameters, the device won't reboot.

Please combine the actual demand and storage capacity to configure the video and audio parameters.

Stream Type The stream type of camera can be set as Main Stream or Sub Stream. By default, it is Main Stream. The main stream is used for HD storage and preview; the sub stream is used for SD storage and preview when the network bandwidth is insufficient.

Video Type The video type can be set as Video or Video & Audio. By default, it is Video & Audio, where video contains sound and images. If you don't need sound, choose Video Stream.

Bitrate Type The bitrate type can be set as Constant or Variable. By default, it is Constant, where you should select a constant value from the Bitrate drop-down box. You are supposed to select

Panic Alarm Station User Manual

36

the maximum bitrate when the bitrate type is set as Variable. Video Quality

You are able to choose different level of the video quality. The video quality is not optional by default when the bitrate type is Constant.

Resolution According to the requirements for video clarity, the higher the resolution, the higher the bandwidth requirement for the network.

Frame Rate Video frames per second. According to the actual bandwidth setting, the higher the video frame rate, the higher the required bandwidth and the higher the required storage space.

I Frame Interval The number of frames between the two key frames before and after. The larger the I frame interval is, the smaller the code stream fluctuation is, but the image quality is relatively poor. Otherwise, the code stream fluctuation is larger and the image quality is higher. It is recommended to use the default value.

Audio Encoding Type When the stream type is the Main Stream, the audio encoding type can be set as G711_U, AAC or PCM. And the audio encoding type of the sub stream is the same as the audio encoding type set in the main stream.

Video Encoding Type By default, it is STD_H264.

SVC It is a scalable video coding technology. The SVC function can be used for framed video recording to reduce storage space. The framed video file still supports normal decoding. When the SVC function is selected to be On, both the storage device and the decoding device must be required to support the function. When the SVC function is selected as Auto, the device will adapt to the current network environment and decide whether to send framed video to ensure that the image can be previewed normally.

File Size According to the video and audio parameters, the video file size of the whole day will be automatically calculated.

After the video and audio parameters are changed, the device won't reboot.

Please combine the actual demand and storage capacity to configure the video and audio parameters.

Edit the display information of the camera.

Click to enter the Remote Configuration page, go to Image View Scale.

Panic Alarm Station User Manual

37

View Scale

Select a camera from the drop-down box to configure the display parameters of the camera, including display position, display format and optional display content, you are able to add custom display information.

Editing the display position

Drag the blue box on the live view page to change the position of the display information, click Save, and then the position of the display information will be updated.

Editing the display format

Date Format Select the display format of the date in the Date Format Drop-Down box.

Time Format Select Time Format as 24-hour or 12-hour.

OSD Format There are four freely combined display status to choose from depending on whether the display information is transparent or flashing. For example, when the display status is Transparent & Blinking, the displayed information will be displayed with a certain transparency and will flash. .

Editing the display content

You are able to select the display content optionally, edit the camera name, and add the custom display content.

Selecting the display content

Panic Alarm Station User Manual

38

According to your requirement, check Display Name, Display Date, Display Week to display the selected display content. Click Save to save the settings.

Editing the camera name

Editing the camera name in the Camera Name text box and click Save.

Adding custom display content

Click the right area of the check box in the Text Overlay List and enter display content in the text box. Check the text and click Save to display the custom information.

You can drag the content to modify the location, or remove the check to cancel the display.

For the device with camera, you can set the image parameters for camera. Click to enter the Remote Configuration page, go to Image Picture Settings.

Picture Settings Page

Select a camera to configure the mode.

Click to enter the Remote Configuration page, go to Image Intercom Audio.

Panic Alarm Station User Manual

39

Intercom Audio

Select the Audio Encoding Type as G711_U, PCM, ADPCM, AAC, or OPUS from the drop-down box. And click Save to save the settings.

System Settings

Click to enter the Remote Configuration page, go to Device Information Time.

Time

You can set the time zone, NTP, DST on the Time page.

You can also click Synchronization to implement SDK synchronization.

Set the device name, device No. and configure the video files.

Panic Alarm Station User Manual

40

Click to enter the Remote Configuration page, go to System General Parameters.

General Parameters

Set the device name and device No.. Click Save to save the settings.

Enable/disable SSH service, which is used to provide security configuration for remote debugging.

Click to enter the Remote Configuration page, go to System Security.

Secuirty

Check Enable SSH to enable SSH service, and click Save.

By default, the SSH service is not enabled. The default setting will be restored after the restart.

Set the maximum password attempts, the lock duration of the locked user. And you can unlock the user remotely.

Steps

1. Click to enter the Remote Configuration page, go to System Password Management.

Panic Alarm Station User Manual

41

Password Management

IP Address The IP address of the terminal in which the locked user logs.

Unlock The user's access lock status on the corresponding IP address.

2. Enable the access lock function and set the lock parameters.

1) Check Access Lock to enable the access lock function.

2) Set the user lock parameters, including maximum password attempts and lock duration.

Max. Password Attempts The maximum times that the user attempts to enter the password. By default, it is 7, the available value is 3 to 10.

Lock Time The lock duration of the locked user. By default, it is 600 s, the available value is 10 to 3600 s.

3) Click Save.

3. Optional: Click Unlock All to unlock all user.

Steps

The device only has the admin user and only supports modifying the admin user password.

1. Click to enter the Remote Configuration page, go to System User.

2. Edit the admin user password.

1) Select the admin user and click Edit.

Panic Alarm Station User Manual

42

2) Enter the new password and confirm it.

3) Click Save.

User

Search and view the alarm logs, exception logs, operation logs and event logs.

Click to enter the Remote Configuration page, go to System Log Query.

You can set the search criteria and click Search, and the search result is in the list.

Panic Alarm Station User Manual

43

Log Query

You can click Backup and download the search result.

Click to enter the Remote Configuration page, go to System Security Audit Log.

Security Audit Log

Panic Alarm Station User Manual

44

1. Check Enable Log Upload Server.

2. Set log server IP and server port.

3. Click to upload the CA certificate.

4. Click Save.

System management and remote upgrade.

Click to enter the Remote Configuration page, go to System System Maintenance.

System Maintenance

System Management

You can reboot the device, restore default settings, restore all settings, and import/export configuration file.

Reboot Restart the device.

Restore Default Settings Restore the default settings, that is, except the IP address and user information, all other parameters of the device will be restored to factory default settings.

Restore All Restore all the parameters to factory default settings, and the device needs to be reactivated after restoring the parameters to default.

Import Configuration File Import the configuration file from the client software to the device.

Panic Alarm Station User Manual

45

The configuration file contains the parameter information of the device.

It is required to enter the password created when exporting when import a file. Export Configuration File

Export the configuration file from the device to the client software.

The configuration file contains the parameter information of the device.

It is required to set a password for the exported file. The password is used for importing verification.

Remote Upgrade

Upgrade the device remotely via the client software.

Click and select the upgrading file. And click Upgrade to upgrade the device.

An invalid upgrade occurs when using a mismatched upgrade file, and then the device program is still the program before the upgrade.

Do not power off the device during the upgrade process.

Automatically or manually check the video and audio status. Click to enter the Remote Configuration page, go to System Video/Audio Self-Check.

Figure 3-39 Video and Audio Check Page

Panic Alarm Station User Manual

46

Auto check

Check the video and audio status automatically. Check Enable, set the detection time and click Save.

Note

The detection time can be selected as none, everyday or one day of the week.

None

Auto check function is not enabled.

Everyday

Check every day according to the set time.

One day of the week

The device performs a check at the set time on this day of the week.

Manual check

Click Verity to start the check and the check results are displayed in the list.

Table 3-1 Description of Check Results

Check results Description

Normal Video/audio input/audio output signal is normal.

Exception Video/audio input/audio output signal is loss.

Unknown Audio input is exception and cannot detect audio output status.

Click to enter the Remote Configuration page, go to Device Information Device Information.

Device Information

Panic Alarm Station User Manual

47

Check Status

Click to enter the Remote Configuration page, go to Status Zone, you can view the status of zone alarm.

Click to enter the Remote Configuration page, go to Status Relay, you can view the relay status.

Other Settings

Enable the auxiliary power output to use the 12 V auxiliary power.

Steps

1. Click to enter the Remote Configuration page, go to Other Auxiliary Power Output.

Auxiliary Power Output Configuration

2. Click , and select the Aux Power Output as Not Support or 12V

Not Support

Disable the auxiliary power output.

12V

Enable the auxiliary power output. 3. Click Save.

Panic Alarm Station User Manual

48

Chapter 4 Web Client Settings

Live View

You can see channel status, alarm log, zone, local relay, network status, device information, hardware status, etc. on live view page.

Figure 4-1 Live View Page

Configuration

System Settings Basic Information

Click System System Settings Basic Information. You can change device name in this page. And you can see device No., Model, Serial NO., version, etc.

System Settings Time Settings

Click System System Settings Time Settings. Select Time Zone.

NTP

Configure Server Address, NTP Port and Interval. The device will periodically synchronize time from the FTP server according to the interval.

Manual Time Sync.

Click Sync. with computer time, the computer time will be synced to the device.

Panic Alarm Station User Manual

49

Enable DST. Configure Start Time, End Time and DST Bias. Click Save.

System Settings About

Click System System Settings Time Settings. Click View Licenses to view open source software licenses.

User Management

Click System User Management. You can see all online users.

Network Settings

Steps 1. Click Network Network Settings TCP/IP. 2. Enter IPv4 Address, IPv4 Subnet Mask, etc., or enable DHCP to get address automatically. 3. Click Save.

Network Service

Steps 1. Click Network Network Service. 2. Configure port parameters.

Note

Please do not change the default port parameters at will. When there is a port conflict and you need to change the port number, please change the following information accordingly.

HTTP(S)

- HTTP The default HTTP port is 80. To change the port, you need to add the changed port number after the address when you log in using the browser. For example, if the HTTP port number changes to 81, you need to enter http://192.168.1.64:81 (The front part of ":" is the current IP address of the device). - HTTPS The default HTTPS port is 443. The range is 1 to 65535. - HTTP Listening Select Server Type as IP or Domain Name. Enter IP or domain name, URL and port.

RTSP

The default RTSP port is 554. It is the real time transport protocol port. Please ensure that the port you changed is available.

Sever Port

The default server port is 8000. When using the client to log in, if the server port is changed,

Panic Alarm Station User Manual

50

you need to enter the port number in the login page. 3. Go to NAT page, enable UPnP to open the device port. 4. Select Port Mapping Mode as Auto or Manual.

Auto

You do not need to set port mapping on the router. You can open the port only by enabling UPnP.

Manual

When you select Manual and enable UPnP, you need to enter the external port number and enable UPnP on the router to open the port. You do not need to change the port of the device itself.

5. Click Save.

Device Access - SIP

After setting the SIP server, the device will be enrolled to the SIP server automatically. The devices under the same SIP server address can communicate with each other. Click Network Device Access SIP.

Private Protocol

Steps 1. Enable SIP.

Enrollment Status

Display the device enrollment status. If the device has been enrolled to the SIP server, it displays Enrolled. Otherwise it displays Not Enrolled.

2. Select IPv4 or Domain. 3. Set parameters.

Device ID

The device ID can only be set as a number and no more than 6 digits. It is a unique identification of the device, which facilitates the interaction between the panic alarm center station and front-end device.

Device Location

You can enter the device location information with a maximum of 32 characters.

User Information

You can enter IP, Server Port, Enrollment Password, etc.

Local Port

The default local port is 5060.

Enrollment Period

The time interval between devices registering with the SIP server. 4. Click Save.

Standard SIP Protocol

Panic Alarm Station User Manual

51

Steps 1. Enable SIP.

Enrollment Status

Display the device enrollment status. If the device has been enrolled to the SIP server, it displays Enrolled. Otherwise it displays Not Enrolled.

2. Select IPv4 or Domain. 3. Set parameters.

User Information

You can enter IP, Server Port, User Name, Enrollment Password, etc.

Local Port

The default local port is 5060. 4. Click Save.

Device Access Hik-Connect

Ezviz is a micro video service platform. After enrolling devices to Ezviz platform, you can access the devices through Ezviz.

Steps 1. Click Network Device Access Hik-Connect. 2. Enable Ezviz Cloud.

Note

When it is enabled for the first time, you need to set the verification code.

3. Set Server Address. You can select default or custom. When Custom is checked, you need to set the server address manually. You can contact the

technical support to get the address. 4. Set Network Mode. The default mode is wired network. 5. Enter the set verification code. The code is a 6-sigit random code used for QR code encryption. It

can be set to 6~12 characters and supports English letters (case sensitive) and numbers. It is recommended to combine more than 8 digits of numbers and letters.

6. Click View to see the Hik-Connect QR code. 7. Click Save.

Device Access - ISUP

ISUP platform refers to Intelligent Security Uplink Protocol. Steps 1. Click Network Device Access ISUP. 2. Enable ISUP. 3. Select Protocol Version as Ehome2.0 or ISUP5.0. 4. Select Server Type as IPv4 or Domain. 5. Set parameters.

Port

The default port number is 7660. The range is 2000 to 65535.

Panic Alarm Station User Manual

52

Device ID

The device ID number can only be set as a number and no more than 6 digits. The ID is the unique identification of the device, which facilitates the interaction between the panic alarm center station and front-end device.

6. Click Save.

Alarm Communication

Steps 1. Click Network Alarm Communication. 2. Enable Wired Network and set parameters.

Notify Surveillance Center

Each network card only supports one upload center, which is Wired Network1 by default.

Server Type

Address type of central server. You can select as IPv4 or Domain.

IP/Domain

Enter the IP address or domain name of the server according to the set server type.

Port

The central port number. The HIK protocol is 7200 by default. The NAL2300 protocol should be set as 4001.

Protocol

The default protocol is HIK Protocol.

User Name

It supports numbers and letters. The HIK protocol can set the length range to 6~9 digits. The NAL2300 protocol can set the length range to 6 digits.

3. Click Save.

Configure the video and audio parameters of the channels.

Video

Click Video/Audio Video toset video parameters, which will take effect after saving.

Stream Type

You can select Main Stream or Sub-Stream to see the live view. The default type is main stream. Main stream is used for high-definition storage and preview. Sub-stream is used for standard definition storage and preview when the network bandwidth is insufficient.

Video Type

You can select Mixed Flow or Video Flow. The default is mixed flow, that is, the video contains sound and pictures. If you do not need sound, you can select video flow.

Panic Alarm Station User Manual

53

Resolution

Select according to the requirements of video definition. The higher the resolution, the higher the network bandwidth required.

Bit Rate Type

You can select Constant Bit Rate or Variable Bit Rate. The default is constant bit rate. If constant bit rate is selected, you need to select a fixed rate value; if variable bit rate is selected, you need to select a limit value of the rate.

Image Quality

You can select different levels of image quality according to your requirements. The higher the quality, the higher the network bandwidth required. When the bit rate is constant bit rate, the image quality can not be selected by default.

Frame Rate

Display the number of frames per second of the video. According to the bandwidth settings, the higher the frame rate, the higher network bandwidth required, and the higher the storage space required.

I Frame Interval

The number of frames between the two key frames. The larger the I frame interval is, the smaller the code stream fluctuation is, but the image quality is relatively poor. On the contrary, the larger the code stream fluctuation is, the higher the image quality is. It is recommended to use the default value.

Video Encoding

The default video encoding type is H.264.

SVC Encoding

It is an expandable video encoding technology. The SVC function can be used to extract frames for video recording to reduce storage space. The video files after frame extraction still support normal decoding. When the SVC function is enabled, the storage device and the decoding device should all support this function. When the SVC function is selected as automatic, the device will adapt to the current network environment and decide whether to send frames to ensure that the image can be previewed normally.

Video&Audio Encoding

The video and audio encoding type supported by the current device. When the stream type is the main stream, the types are G.711ulaw, AAC, PCM; The sub-tream is consistent with the main stream.

Audio

Steps 1. Click Video/Audio Audio. 2. Set parameters.

Audio Encoding

The current device supports G.711ulaw, AAC, OPUS, PCM and ADPCM.

Panic Alarm Station User Manual

54

Audio Input

The input type is micln by default. You can set the volume.

Audio Output

The output type is spkOut. You can set the volume. 3. Click Save.

Figure 4-2 Audio Parameters

Steps 1. Click Image OSD Settings. 2. Set parameters.

Change Display Position

Drag the red box on the preview interface to change the position of the displayed information. After saving, the displayed information will be updated to a new position.

Change Display Format

- Date Format You can select the date display format in the date format drop-down box. - Time Format You can select 24-hour or 12-hour format in the time format drop-down box. - Display Mode According to whether the display information is transparent or flashing, there are four freely combined display mode for selection. For example, if the display mode is transparent and flashing, the information will be displayed with a certain transparency and will flash. - OSD Size

Panic Alarm Station User Manual

55

You can select the font size in the OSD size drop-down box. - Alignment You can select Align Left, Custom, Align Right or International Mode in the alignment drop- down box.

Change Display Content

You can select the display content on the image, including the channel name, date and week, or change the channel name and add customized display content. - Display Content Select whether to display the name, date or week according to your need. After selecting, the corresponding information will be displayed on the image. - Channel Name You can change the channel name in the channel name text box. - Custom In the Text Overlay interface below, click +Add, and the text input box will appear. Enter content, and the customized content will be displayed in the image.

3. Change the image refresh time interval above the screen.

Figure 4-3 OSD Settings

Zone Settings

Steps 1. Click Device Zone.

2. Click to enter the Zone Settings page.

3. Set parameters.

Detector Type

Panic Alarm Station User Manual

56

Type of zone detector.

Zone Type

- Instant Under the arming status, as long as the detector connected to the zone is triggered, the alarm controller will immediately generate an alarm without delay. - Fire The fire zone is a 24-hour alarm zone. When the fire zone is triggered, the external sounder will give a fire alarm sound. - 24H Silent Zone Detectors working in this zone are on alert for 24 hours, and will not be affected by arming and disarming operations. Once triggered, they will immediately transmit information to the command center, but there is no alarm sound. - Disabled No event will trigger an alarm.

Audio File

Select the zone audio file. Mute can be selected.

Upload Restored Alarm

After enabling, when the alarm is recovered, the report will be uploaded to the center. 4. Check the Link Relay, Linked Channel, etc. 5. (Optional) Click Copy to, copy the zone parameters to other zones. 6. Click Save.

Relay Settings

Steps 1. Click Device Relay.

2. Click to set relay parameters.

Output Delay

After the zone event is triggered, the relay will close the relay output after the output delay. The setting range is 0 to 2000 seconds.

3. Click Save. 4. Check the relay, click ON or OFF to open or close the relay.

Auxiliary Power Output

Steps

1. Click Device Auxiliary Power Output.

2. Enable Switch of Auxiliary Power Output.

3. Click Save.

Panic Alarm Station User Manual

57

Calling Settings

Steps

1. Click Two-way Audio Settings Calling Settings.

2. Configure parameters.

Call Timeout

Refers to the playing time of the call prompt tone. The range is 40 to 60 seconds.

Call Extension Time

When you press the call wait during calling the panic alarm center station, the extension time of the prompt tone based on the maximum ringing time is call extension time. The range is 10 to 60 seconds.

3. Click Save.

Voice Prompt

Steps

1. Click Two-way Audio Settings Voice Prompt.

2. Configure Call Waiting Tone, Reject Tone, Two-way Audio End Tone, Emergency Help Tone.

3. Enable Mute Schedule.

4. Click Mute, move the mouse over the time bar, and long press and drag the left mouse button to draw the time period.

Figure 4-4 Mute Schedule Settings

5. Edit the time period.

Edit Time Period Length and Start/End Time

Panic Alarm Station User Manual

58

Click the drawn time period to adjust the start/end time in the pop-up window.

Delete Time Period

Click Erase, long press and drag the mouse on the drawn time period to erase.

Delete All Time Period

Click Clear All, you can delete all drawn time period.

Copy Time Period

Move the mouse to the time bar, click in the right of the day, and select time period to

copy to that day. Click OK to save.

Figure 4-5 Edit Mute Schedule

6. Click Save.

Remote upload audio files to SD card with storage space.

Steps

1. Click Custom.

2. Click Import, select the file address in the pop-up window and import.

Note

Audio file is .wav or .mp3 format, the file name can be composed of English characters, numbers and Chinese characters, and does not contain spaces at the beginning and end. The length of the file name (including the suffix of 4 bytes) is up to 31 English characters (9

Chinese characters). The symbols that cannot be included in the file name are:\/* <>|.

The maximum size of each audio file is 2MB. Uploading audio files with the same name will overwrite the audio files before.

3. Check audio files to be deleted, Click Delete, all the checked files will be deleted.

Note

Multiple files can be deleted for batch deletion. After deleting the audio file in SD card, and use the function of the file, the name will recover

Panic Alarm Station User Manual

59

to the default audio file.

Maintenance and Security

Reboot

Click Maintenance and Security Maintenance Reboot to restart the device manually.

Upgrade

Steps

Click Maintenance and Security Maintenance Upgrade. Click , select the upgrade file.

Click Upgrade.

Note

When upgrading an unmatched upgrade file, the upgrade fails and remains the same as before.

During the upgrade process, do not power off the device.

Backup and Reset

Click Maintenance and Security Maintenance Backup and Reset.

Export

Click Export to export configuration file, which includes device parameters.

Restore to Default Settings

Click Restore, device parameters except for IP address will restore to default settings.

Restore to Factory Settings

Click Default, all device parameters will restore to default settings, and you need to activate the device when you use it again.

Import Parameters

Select file and click Import, the configuration file will be imported to device.

Log

Click Maintenance and Security Maintenance Log, set Major Type, Minor Type and Select Time, click Search, the query results will be shown.

Security Audit Log

Click Maintenance and Security Maintenance Security Audit Log, enable Log Upload Server. Configure Log Server IP and Log Server Port, and import CA Certificate.

Panic Alarm Station User Manual

60

Audio&Video Self-Test

Click Maintenance and Security Maintenance Audio&Video Self-Test, set manual test or auto test.

Auto Test

Audio and video self-test will be automatically performed according to the set detection time.

Restore to Default Settings

Click Test, the results will be shown in the result table.

Test Result Note

Normal Video/audio input /audio output signal is normal.

Exception Video/audio input /audio output signal is lost.

Unknown Audio input fails. It is unable to detect audio output status.

IP Address Filter

Steps

1. Click Maintenance and Security Security IP Address Filter.

2. Enable filter, click +Add to add IP address to the list.

3. Click to change IP address. Click to delete address.

4. Click Save.

Block List

The IP address in this list will be blocked. Other IP address can communicate normally.

Allow List

Only the IP address in this list can communicate normally. Other IP address will be blocked.

Note

You can only enable one kind of list.

Security Service

Click Maintenance and Security Security Security Service.

Enable SSH, and click Save.

Note

SSH is used for remote debugging. For your safety, it is recommended to disable SSH when it is not needed.

Panic Alarm Station User Manual

61

Locking User

Steps

1. Click Maintenance and Security Security Locking User.

2. Enable Locking, set parameters.

Max. Failure Attempts

The default setting is 7 times, and the setting range is 3 to 10.

Locking Duration

The default setting is 600 seconds, and the setting range is 10 to 3600.

3. Click Save.

Note

If you enter the wrong password more than the set number of times, the IP address of the login terminal of the locked user will be displayed in the list.

4. (Optional) The user can be unlocked through the following operations.

Click to unlock the locked user in the list.

Click Unlock All to unlock all locked users.

Manualsnet FAQs

If you want to find out how the DS-PEA102Y Hikvision works, you can view and download the Hikvision DS-PEA102Y Panel User's Manual on the Manualsnet website.

Yes, we have the User's Manual for Hikvision DS-PEA102Y as well as other Hikvision manuals. All you need to do is to use our search bar and find the user manual that you are looking for.

The User's Manual should include all the details that are needed to use a Hikvision DS-PEA102Y. Full manuals and user guide PDFs can be downloaded from Manualsnet.com.

The best way to navigate the Hikvision DS-PEA102Y Panel User's Manual is by checking the Table of Contents at the top of the page where available. This allows you to navigate a manual by jumping to the section you are looking for.

This Hikvision DS-PEA102Y Panel User's Manual consists of sections like Table of Contents, to name a few. For easier navigation, use the Table of Contents in the upper left corner.

You can download Hikvision DS-PEA102Y Panel User's Manual free of charge simply by clicking the “download” button in the upper right corner of any manuals page. This feature allows you to download any manual in a couple of seconds and is generally in PDF format. You can also save a manual for later by adding it to your saved documents in the user profile.

To be able to print Hikvision DS-PEA102Y Panel User's Manual, simply download the document to your computer. Once downloaded, open the PDF file and print the Hikvision DS-PEA102Y Panel User's Manual as you would any other document. This can usually be achieved by clicking on “File” and then “Print” from the menu bar.