Hikvision DS-D5050UC-C Monitor User's Manual PDF

1 of 40
1 of 40

Summary of Content for Hikvision DS-D5050UC-C Monitor User's Manual PDF

Monitor

User Manual

iii

- Reorient or relocate the receiving antenna. - Increase the separaon between the equipment and receiver. - Connect the equipment into an outlet on a circuit dierent from that to which the receiver is connected.

- Consult the dealer or an experienced radio/TV technician for help.

Regulatory Informaon(For 50/55 Model)

FCC Informaon Please take aenon that changes or modicaon not expressly approved by the party responsible for compliance could void the users authority to operate the equipment. FCC compliance:This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable!protecon against harmful interference in a residenal installaon. This equipment generates,uses and can radiate radio frequency energy and, if not installed and used in accordance with the instrucons, may cause harmful interference to radio communicaons. However, there is no guarantee that interference will not occur in a parcular installaon. If this equipment does cause harmful interference to radio or television recepon, which can be determined by turning the equipment o and on, the user is encouraged to try to correct the interference by one or more of the following measures:

FCC Condions This device complies with part 15 of the FCC Rules. Operaon is subject to the following two condions: 1. This device may not cause harmful interference. 2. This device must accept any interference received, including interference that may cause undesired operaon.

EU Conformity Statement

This product and - if applicable - the supplied accessories too are marked with "CE" and comply therefore with the applicable harmonized European standards

listed under the EMC Direcve 2014/30/EU, the LVD Direcve 2014/35/EU, the RoHS Direcve 2011/65/EU.

2012/19/EU (WEEE direcve): Products marked with this symbol cannot be disposed of as unsorted municipal waste in the European Union. For proper recycling, return this product to your local supplier upon the purchase of

equivalent new equipment, or dispose of it at designated collecon points. For more informaon see: www.recyclethis.info

2006/66/EC (baery direcve): This product contains a baery that cannot be disposed of as unsorted municipal waste in the European Union. See the product documentaon for specic baery informaon. The baery is marked

with this symbol, which may include leering to indicate cadmium (Cd), lead (Pb), or mercury (Hg). For proper recycling, return the baery to your supplier or to a designated collecon point. For more informaon see: www.recyclethis.info Industry Canada ICES-003 Compliance This device meets the CAN ICES-003(B)/NMB-003(B) standards requireme nts.

iv

Regulatory Informaon(For 65 Model)

FCC Informaon Please take aenon that changes or modicaon not expressly approved by the party responsible for compliance could void the users authority to operate the equipment. FCC compliance:This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protecon against harmful interference when the equipment is operated in a commercial environment. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instrucon manual, may cause harmful interference to radio communicaons. Operaon of this equipment in a residenal area is likely to cause harmful interference in which case the user will be required to correct the interference at his own expense. FCC Condions

This device complies with part 15 of the FCC Rules. Operaon is su bject to the following two condions: 1. This device may not cause harmful interference. 2. This device must accept any interference received, including interference that may cause undesired operaon.

EU Conformity Statement

This product and - if applicable - the supplied accessories too are marked with "CE" and comply therefore with the applicable harmonized European standards

listed under the EMC Direcve 2014/30/EU, the LVD Direcve 2014/35/EU, the RoHS Direcve 2011/65/EU.

2012/19/EU (WEEE direcve): Products marked with this symbol cannot be disposed of as unsorted municipal waste in the European Union. For proper recycling, return this product to your local supplier upon the purchase of

equivalent new equipment, or dispose of it at designated collecon points. For more informaon see: www.recyclethis.info

2006/66/EC (baery direcve): This product contains a baery that cannot be disposed of as unsorted municipal waste in the European Union. See the product documentaon for specic baery informaon. The baery is marked

with this symbol, which may include leering to indicate cadmium (Cd), lead (Pb), or mercury (Hg). For proper recycling, return the baery to your supplier or to a designated collecon point. For more informaon see: www.recyclethis.info Industry Canada ICES-003 Compliance This device meets the CAN ICES-003(A)/NMB-003(A) standards requirements. This is a class A product and may cause radio interference in which case the user may be required to take adequate measures. WARNING: This equipment is compliant with Class A of EN55032/CISPR 32. In a residenal environment this equipment may cause radio interference.

v

Applicable Models

This manual is applicable to 50/55/65 Inch Monitor.

vi

Safety instructions

Pixel feature This liquid crystal display product has ultrahigh color resolution. While its effective pixels are up to 99.999% or higher, it is still possible that a dark spot or a bright spot (red, green or blue) constantly appears on the screen. This is the structure property (within the general industrial standard) of the display rather than a fault. The monitor will appear picture crash then reboot if influenced by strong electrostatic interference, it may self- recovered or need manual recovered to original status. Safety Please read and understand all instructions before using the monitor safety . Damage resulting from nonobservance of the instructions is not covered by the warranty. Be careful of electric shock and fire! Never make the monitor contact with rain or water. Never place a liquid container (e.g.,

a vase) near or on the monitor. Please disconnect the monitors power immediately if a liquid is spilled on the monitors surface or inside. Please contact the customer service center before using it again.

Never put a monitor, remote controller, or battery near an open flame or other heat source (including direct sunlight). In order to avoid flame spread, always keep candles or other open flames away from monitors, remote controls, and batteries.

Never insert any object into the ventilation slot or other openings on the monitor. Please make sure that the power line is not taut. The tightening of the power line will

loose the power connections and produce sparks. Beware of short circuit or fire! Do not expose the remote controller or battery in rain, water or overheated environment. Please avoid pulling the plug. Loose power plugs may spark or cause fire. Watch out for personal injury or monitor damage! It is suggested that the monitor be carried by two people. When installing the monitor on the stand, please use only the chassis provided. Firmly

fix the frame on the monitor. Put the monitor on a flat, flat surface that can withstand the total weight of the monitor and the chassis.

When installing a monitor with wall mounting, please use only the wall mount bracket that can bear the weight of the monitor. Fix the wall mount mounting bracket on the wall that can withstand the total weight of the monitor and the wall mount bracket. The company is not responsible for the accident, personal injury or loss caused by improper installation.

Be careful of hurting children! Please follow the following precautions to avoid child injury due to monitor falling:

vii

Never place the monitor on a surface covered with a cloth or other material that can be pulled.

Make sure that any part of the monitor is within the edge of the surface. When placing a monitor on a high furniture (such as a bookcase), the furniture and

monitor must be fixed to the wall or the appropriate support. Tell children about the dangers of climbing furniture and touching monitors. Beware of eating battery! The remote control of this product contains batteries. There is a risk that children might

eat the batteries. Please keep them out of reach of children. Watch out for overheating! Never install the monitor in the enclosed space. Always leave at least 4 inches or 10

centimeters of space around the monitor for ventilation. Make sure that curtains or other objects do not block the ventilation slot on the monitor.

Be careful! Dont break the monitor! Before you connect the monitor to the power outlet, make sure that the power voltage

matches the value printed on the back of the monitor. If the voltage is different, dont connect the monitor to the power outlet.

If the monitor is not used for a long time, please cut off the power supply. Be careful of personal injury, fire or power line damage! Do not put the monitor or any object on the power line. As a disconnecting device, the power plug should be kept to operate conveniently. When the power line is disconnected, always hold the plug instead of pulling the cable. Before the thunderstorm comes, disconnect the monitor from the power outlet and

the antenna. Never touch any part of a monitor, a power line, or an antenna in a thunderstorm.

The wired network antenna connected to the equipment must be isolated from the protective grounding, otherwise it may cause fire and other dangers!

Watch out for hearing impairment!

Avoid using headphones or earphones at high volume or for a long time. Low temperature If the monitor is transported below 5C, please open the package of the monitor. Wait for

the monitor to adapt to the room temperature, and then connect the monitor to the power outlet.

viii

This manual is for reference only, please refer to the actual machine.

1. Unpacking and installation

1.1. Unpacking This product is packed in a paper packing case and comes with standard accessories. Any other optional parts are individually packed. Considering the size and weight of the monitor, it is recommended to move this monitor

by two persons. Please confirm that items are complete and intact after opening the packing case.

1.2. Items in the packing case Please confirm that the packing case contains the following items:

LCD monitor Remote control Instructions Power cord HDMI cable Bracket x 2

* The supplied power cord varies depending on destination

Bracket

User ManualRemote Control

Power Cord HDMI Cable

Monitor

User Manual

Notes: For all other regions, the power cords shall be matched with the AC voltage of the power

socket, conform to the regulations of the relevant laws of the countries/territories, and pass certification. ( Types H05VV-F, 2G or 3G 0.75 or 1mm2 shall be used.)

You can keep the packing case and packaging materials for later transport of the monitor.

1.3. Installation precautions This product belongs to high-power-consumption products. Please always use the plug

specially designed for this product. If you need to extend the wire, please consult your service provider.

This product should be installed on a plane to avoid overturn. The rear part of this product should be kept away from the wall at a certain distance so as to maintain proper ventilation. This product shall not be installed in the kitchen, bathroom or any other locations with high humidity, to avoid shortening the service life of the electronic components.

This product works only at an altitude below 3000m. If the installation site is higher than 3000m, some abnormalities may occur.

ix

1.4. Installation for the base of the mounting desk: Install the base: 1. Spread the protective film (wrapped on the monitored during packing) on the desk, and

place the monitor with its front face down on the protective film (keep the trademark off the desk) to avoid scratching the screen.

2. Align the base according to the figure (distinguish the left and right supports). There are R and L marks on the base. Lock screws.

3. Lift the monitor and place it.

R

L

L

R

x

1.5. Hang the monitor on the wall In order to install the monitor on the wall, you must prepare a set of standard wall-hanging kit (separately purchased). You are recommended to use the mounting plate which conforms to the TUV-GS and/or UL1678 standard.

Protective Sheet

Table

VESA Grid

1. Spread a protective sheet which was wrapped around the display when it was packed on a flat surface. Lay the display face-down on the protective sheet to facilitate your operation without scratching the screen.

2. Ensure that you have all accessories necessary for any type of mounting (hanging rack, lifting rack, desk base, etc.).

3. Follow the instructions that come with the base mounting kit. Failure to follow correct mounting procedures could result in damage to the equipment or injury to the user or installer. Product warranty does not cover damage caused by improper installation.

4. For the wall-mounting kit, use M6 mounting screws (with a length 20 mm(50")/26mm(55") 25mm(65") longer than the thickness of the mounting bracket) and tighten them securely.

1.5.1. VESA grid plate 50 200(H) x 200(V) mm

55 200(H) x 200(V) mm

65 300(H) x 300(V) mm

Caution: Prevent the monitor from falling down: In the case of wall installation or suspended installation, it is recommended to use the

metal assembling rack available on the market to install the monitor. Refer to the guide attached to the assembling rack for specific installation instructions.

In order to lower the probability that the monitor falls down and results in personal injuries and property loss under the condition of earthquake or other natural disasters, please do consult the assembling rack manufacturer to confirm the installation position.

xi

Table of contents 1. Unpacking and installation ......viii

1.1. Unpacking .............................. viii 1.2. Items in the packing case ...... viii 1.3. Installation precautions .......... viii 1.4. Installation for the base of the

mounting desk: ........................ ix 1.5. Hang the monitor on the wall ....x

1.5.1. VESA grid plate .................x

2. Parts and functions ....................2 2.1. Control panel ............................2 2.2. Input/output terminal .................3 2.3. Remote Control ........................4

2.3.1. General functions ..............4 2.3.2. Install batteries into the

remote control ...................5 2.3.3. Maintenance of the remote

control ...............................5 2.3.4. Working scope of the

remote control ...................6

3. Connect external devices ..........7 3.1. Connect external devices (DVD/

VCR/NVR) ................................7 3.1.1. Use HDMI video input .......7

3.2. Connect PC ..............................7 3.2.1. Use HDMI input .................7 3.2.2. Use VGA input ..................8

3.3. Connect USB ............................8 3.3.1. Use USB device ................8

4. Operation ...................................9 4.1. Play multimedia files from USB

device .......................................9 4.1.1.Photo .................................10 4.1.2.Music .................................11 4.1.3.Movie .................................12 4.1.4.Text ....................................13

4.2. Operation on the OSD menu: .14

5. Compatibility of the USB device ......................................17

6. Input mode ..............................20

7. Cleaning and Troubleshooting .21 7.1. Cleaning .................................21 7.2. Troubleshooting ......................22

8. Technical specification .............24

1

Ventilation requirements for enclosed space In order to ensure normal heat dissipation, sufficient space from items to four sides shall be kept, as shown in the figure below.

100 mm 100 mm

100 mm

100 mm

2

2. Parts and functions

2.1. Control panel

1

2

1 Power button Turn the display On or put the display to standby mode.

2 Remote control sensor and power status indicator.

3

2.2. Input/output terminal

AUDIO-IN VGA

U SB

5. 0V

5 00

m A

1 2 3

4

5

6

7

IN 1

IN 2

R S2

32

1 AC IN AC power input from the wall socket.

2 AUDIO IN Audio input for VGA source

3 VGA IN VGA video input.

4 RS232 Receive command signals from the external RS232 device.

5 USB port Connect to the USB storage device.

6 HDMI 1/ 7 HDMI 2 HDMI 1 support HDMI 1.4, up to 4K @30Hz. HDMI 2 support HDMI 2.0, up to 4K @60Hz.

4

2.3. Remote Control 2.3.1. General functions

1

7

2

19

18

4

8

6

13

20

17

9 12

14

11

15

3

10

5

16

1 [ ] POWER button Turn on or turn off the display.

2 [Source] Button Channel switching, source key only supports switching (source).

3 [CMS] button Reserved.

4 [USB] button Go to USB source.

5 [HDMI/PC] button Go to HDMI source.

6 [ ] Time button Reserved.

7 [PLAY] button Control playback of media files.

8 [MENU] SETTINGS button Enter the main menu, or return to previous menu or exit the main menu. The remote control buttons [up], [down], [left], [right] are movement,Under the menu setting, press the left and right buttons to enter the lower menu or adjust the parameters.

9 [INFO] button Show Information OSD.

10 [ ] MUTE button Mute or restore volume.

11 [ ] BACK button Signal source interface or menu interface: prompt exit and press RC [return] to exit.

12 [Vol+]VOLUME button Turn up the volume.

13 [ ] HOME button Reserved.

14 [ ] [ ] [ ] [ ]NAVIGATION buttons Up, down, left and right operation key.

15 [OK] button Press OK to display the message.

16 [Vol-] Volume button Turn Down the volume.

17 [Option] button Reserved.

18 [Number] buttons Input figures or text.

19 [Multi-View] button Reserved.

20 [Help] button Reserved.

5

2.3.2. Install batteries into the remote control The remote control is electrified by two pieces of 1.5V AAA batteries.

Install or replace batteries: 1. Install and push away the battery cover. 2. Place the batteries according to the

marks (+) and (). 3. Close the battery cover.

Caution: Incorrect use of the batteries may result in liquid leak or explosion. Please do abide by the following instructions: To place the AAA batteries in, the marks (+) and () of each of the batteries shall

correspond to the marks (+) and () in the battery compartment. Please do not use batteries of different types at the same time. Please do not use old and new batteries at the same time, otherwise the service life of

the batteries will be shortened or liquid leak will occur. Take out the batteries immediately once the batteries are exhausted so as to avoid liquid

leak in the battery compartment. Please do not touch exposed acid liquid of the batteries, or your skin will be injured.

Notes: Take out the batteries if the remote control is not used for a long time.

2.3.3. Maintenance of the remote control Protect the remote control against violent collision. Do not splash water or other liquid on the remote control. Wipe dry the remote control

immediately if there is liquid thereon. Keep it away from heat and damp. Do not open the remote control except installing the batteries.

6

2.3.4. Working scope of the remote control To press buttons on the remote control, please point the front of the remote control at the remote sensor on the monitor. When the remote control is in use, the distance to the sensor on the monitor shall be smaller than 5m/16 inch, and the horizontal and vertical angles shall be smaller than 30 degrees. Notes: The remote control may fail to work

normally when sunlight or other strong light radiates on the remote sensor of the monitor or there is an obstacle between the remote and the remote sensor.

3030

7

3. Connect external devices

3.1. Connect external devices (DVD/VCR/NVR) 3.1.1. Use HDMI video input

DVD / VCR / NVR

HDMI OUT

[HDMI IN]

IN 1 IN 2

3.2. Connect PC 3.2.1. Use HDMI input

PC

HDMI OUT

[HDMI IN]

IN 1 IN 2

8

3.2.2. Use VGA input

PC

[VGA IN]

[AUDIO IN]

VGA OUT AUDIO IN

AUDIO-IN VGA

3.3. Connect USB 3.3.1. Use USB device

USB 5.0V 500mA

9

4. Operation NOTE: The control button described in this section is mainly on the remote control unless specified

otherwise.

4.1. Play multimedia files from USB device 1. Connect your USB device to the USB port on the display.

U SB

5. 0V

5 00

m A

IN 1

IN 2

R S2

32

2. Press [ SOURCE ] button, choose USB, and press [ ] button.

HDMI1

Input Source

VGA

USB

HDMI2

Move Select ExitENTER EXIT

3. Press [/] to select Photo/Music/Movie/Text icon and [ ] to enter the USB memory.

Photo Music Movie Text

4. Follow the on-screen instruction to control the play option.

10

4.1.1. Photo Select a picture file and press [ ] to view, and it will display all the pictures in the folder automatically. Press [ ] to display the following menu.

Play/Pause Press Play/Pause button to paly or pause the slideshow. Prev./Next Press Next/Prev. button to skip to view the photo which are seclecd

the photo. Stop Press Stop button to stop and return. RepeatAll Press to select the repeat mode: Repeat 1/ALL/None. Music Off Press to play or stop the background music. Playlist Press to view the list of pictures. Info. Press to display the information of the current picture (Resolution/

Size/Date/Time) Rotate Rotate counterclockwise. Zoom in Zoom the picture in. Zoom out Zoom the picture out. Move view Zoom out the picture first. Highlight the icon and press [OK], then

press [/]& [/] to move the picture.

11

4.1.2. Music

Play/Pause Press to play or stop. FB Press to play slower. FF Press to play faster. Prev. Press to play the previous song. Next Press to play the next song. Stop Press to stop and return to folder interface. RepeatAll Press to select the repeat mode: Repeat 1/ALL/None. SET A Select AB mode. Mute Select MUTE mode: on or off . Playlist Seclect to display play list. INFO. Seclect to display the music information. Goto time Seclect to setup play time.

12

4.1.3. Movie

Play/Pause Press to play or pause. FB Press to play slower. FF Press to play faster. Prev. Press to play the previous movie. Next Press to play the next movie. Stop Press to stop and back to folder interface. Charset Character set switching. RepeatAll Press to select the repeat mode: Repeat 1/ALL/None. Set A Select AB mode. Playlist Press to view the list of pictures. INFO. Press to display the information of the current movie. Slow forward Slow forward. Step forward Step forward. Goto time Seclect to setup play time.

13

4.1.4. Text

Prev Page Press to the previous page. Next Page Press to the next page. Prev. Press to play previous text. Next Press to play next text. Stop Press to stop and back to folder interface. Charset Character set switching. Music Off Turn background music on or off. Playlist Press to view the list of texts. INFO. Press to display the information of the current movie.

14

4.2. Operation on the OSD menu:

Column 1 Column 2 Column 1, 3 Column 2, 3 or Column 2, 2 Remarks

Picture

Picture Mode

Security monitoring

Depend on HDMI 1/ HDMI 2

Automatic Depend on HDMI 1/ HDMI 2

Bright Standard Soft

User

Sub items can be adjusted in user mode only, Grayed out in other modes.

Color temp

Standard Adjust different image modes, the default color temperature is the standard.(only user mode can be adjusted, other modes are grayed out)

Warm

User

Cool

Noise Reduction

Off 1. It is not adjustable in computer channel or security monitoring mode, and the display proportion is point-to- point.

2. When entering video timing, noise suppression is adjustable.

3. USB source playing video noise is adjustable.

Low

Middle

High

Default (default value: medium, gray)

Brightness 0 100 Backlight adjustment.

HDMI Mode

Auto The reappearance rate is different under different separation rate and mode.

Video

PC

Sound

Treble 0 100 50: default In mute mode, when you press the key to adjust the sound and balance, the mute icon will disappear.

Bass 0 100 50: default

Balance -50 +50 0: default

15

TIME

Sleep Timer

Off, 10min, 20min, 30min, 60min, 90min, 120min, 180min, 240min

After setting the time, the device will automatically turn off at the time you set. Restart and return to the default value of off.

Auto Sleep Off, 3 hours, 4 hours, 5 hours

Turn off or select no device operation to automatically enter sleep time (3 hours, 4 hours, 5 hours). Default value: turn off.

OSD Timer 5 S / 10 S / 15 S / 20 S / 25 S/ 30 S

Set OSD disappear time.

OPTION

OSD Language

English Set the OSD display language.Chinese

Color Range Auto

VGA, USB source graying is not optional.0-255

16-235

Aspect Ratio

Auto VGA signal: 4:3 / 16:9 / PointToPoint. Note: options are different for different channels, input signal formats and image modes. USB channel does not support proportional mode.

16:9 4:3 Zoom1 Zoom2 Just Scan Panorama PointToPoint

Blue Screen On/Off

After the blue screen is opened, the no signal interface and menu interface display the blue background.

Restore Factory Default

Recall the default setting.

Soft Update USB software to Update

16

SCREEN

Auto Adjust Note: 1. The VGA signal is not connected, so the screen menu cannot be selected; 2. Press up / down key to switch in the process of horizontal position / vertical position / clock / phase adjustment value. When VGA is in the pop-up interface of the automatic adjustment mode, the remote control and the power key have no effect, and the pop-up interface disappears and the system will shut down normally.

Position H.

Position V.

Size

Phase

Position Reset

Note Different input sources may have different OSD options, please refer to the actual OSD (on screen display).

17

5. Compatibility of the USB device Format of the USB multi-media coder-decoder

Spec of AV codec , Video

Type Video coder- decoder Highest bit rate Frame

rate Resolution Audio format

AVI(.avi) MPEG-1, 80Mbps 30FPS 1920x1080 MPEG-1 Layers I,II, III(MP3) AAC, AC3, PCM, WMA, WMAPro

MPEG-2MP@HL, 80Mbps 30FPS 1920x1080 MPEG-4 SP@L0-3, ASP@L0-5,

50Mbps 30FPS 1920x1080

H.264 MP,HP@Level4.1,

100Mbps(VCL) 120Mbps(NAL)

30FPS 3840x2160

VC1 (AP), 45Mbps 30FPS 1920x1080 H263, 5Mbps 30FPS 1280x720 MJPEG, 30FPS 1920x1080

MPEG-2 TS Transport Stream(. ts)

MPEG-2MP@HL, 80Mbps 30FPS 1920x1080 MP3 AAC AC3 PCM

MPEG-4SP@L0- 3,ASP@L0-5,

50Mbps 30FPS 1920x1080

H.264 MP,HP@Level4.1,

100Mbps(VCL) 120Mbps(NAL)

30FPS 3840x2160

AVS benchmark grade@level 6.0,

50Mbps 30FPS 1920x1080

VC1 (AP), 45Mbps 30FPS 1920x1080 H265 100Mbps 30FPS 3840x2160

MPEG File Format (.mpeg)

MPEG-1, 80Mbps 30FPS 1920x1080 PCM, AC3, MP3

MPEG-2MP@HL, 80Mbps 30FPS 1920x1080 H.264 MP,HP@Level 4.1,

100Mbps(VCL) 120Mbps(NAL)

30FPS 3840x2160

H.264 MP,HP@Level 4.1,

100Mbps(VCL) 120Mbps(NAL)

30FPS 3840x2160

MPEG- 4SP@L0-3, ASP@L0-5,

50Mbps 30FPS 1920x1080

H265 100Mbps 30FPS 3840x2160 QuickTime (.mov)

H.264 MP,HP@Level 4.1,

100Mbps(VCL) 120Mbps(NAL)

30FPS 3840x2160 AAC

MPEG- 4SP@L0-3, ASP@L0-5,

50Mbps 30FPS 1920x1080

MJPEG, 30FPS 1920x1080 H265 100Mbps 30FPS 3840x2160

18

BDAV MPEG-2 transport stream (.m2ts)

H.264 MP,HP@Level 4.1,

100Mbps(VCL) 120Mbps(NAL)

30FPS 3840x2160 AC3, AAC,

VC1 (AP), 45Mbps 30FPS 1920x1080 MPEG-2MP@HL, 80Mbps 30FPS 1920x1080

Matroska (.mkv)

H.264 MP,HP@Level 4.1,

100Mbps(VCL) 120Mbps(NAL)

30FPS 3840x2160

VC1 (AP), 45Mbps 30FPS 1920x1080 H265 100Mbps 30FPS 3840x2160

Flash Video (.flv)

H.264 MP,HP@Level 4.1,

100Mbps(VCL) 120Mbps(NAL)

30FPS 3840x2160 AAC, MP3

H263 5Mbps 30FPS 1280x720 Video OBject (.vob)

MPEG-2MP@HL, 80Mbps 30FPS 1920x1080 AC3 PCM MP3

DAT (.dat) MPEG-1, 80Mbps 30FPS 1920x1080 PCM MP3

Advanced Stream Format (.asf)

VC1 (AP), 45Mbps 30FPS 1920x1080 MP3 PCM WMA

H.264 MP,HP@Level 4.1,

100Mbps(VCL) 120Mbps(NAL)

30FPS 3840x2160

MPEG- 4SP@L0-3, ASP@L0-5,

50Mbps 30FPS 1920x1080

3gp H.264 MP,HP@Level 4.1,

100Mbps(VCL) 120Mbps(NAL)

30FPS 3840x2160 AMR_NB, AAC

H263 5Mbps 30FPS 1280x720 MPEG- 4SP@L0-3, ASP@L0-5,

50Mbps 30FPS 1920x1080

tp MPEG-2MP@HL, 80Mbps 30FPS 1920x1080 MPEG-1 Layers II, AC3

trp H.264 MP,HP@Level 4.1,

100Mbps(VCL) 120Mbps(NAL)

30FPS 3840x2160 MP3

MPEG-2MP@HL, 80Mbps 30FPS 1920x1080

19

Spec of AV codec , Audio Type Audio format Sampling Rate Bit rate Windows Media Audio (.wma)

WMA WMAPro

8KHz ~ 48Khz 128bps ~ 320Kbps

MPEG Audio Layer III (.mp3)

MPEG 32kHz ~ 48kHz 32kbps ~ 320kbps

Advanced Audio Coding (.aac)

AAC 16kHz ~ 48kHz 24kbps ~ 384kbps

N/A (Work with video files only)

AC3 32kHz, 44.1kHz, 48kHz

32kbps ~ 640kbps

EAC3 32kHz, 44.1kHz, 48kHz

32Kbps ~ 6 Mbps

OGG Vobis (.ogg) Vorbis 8kHz~48kHz max 320Kbps

Spec of AV codec , Photo Type Maximum resolution Minimum resolution png 8K*8KHardware solutions 4*4 jpeg baseline 8K*8K,

Hardware solutions progressive 4K*4K 4*4

bmp 8K*8K 4*4 Notes: If the standard bite rate/frame rate of the contents is higher than the compatible frames/

second listed in the above table, audio or video may not work. Video contents with a bit rate or frame rate higher than the designated rate in the above

table may result in discontinuation of video during display.

20

6. Input mode PC mode

720 x 400 @ 70Hz

640 x 480 @ 60Hz

640 x 480 @ 75Hz

800 x 600 @ 60Hz

1024 x 768 @ 60Hz

1152 x 870 @ 75Hz

1280 x 720 @ 60Hz

1280 x 1024 @ 60Hz

1366 x 768 @ 60Hz

1920 x 1080 @ 60Hz

1600 x 900 @ 60Hz

1680 x 1050 @ 60Hz

1600 x 1200 @ 60Hz

Video mode 480P - 60Hz

480i - 60Hz

576P - 50Hz

576i - 50Hz

720P - 50Hz/60Hz

1080P - 50/60Hz

1080i - 50/60Hz

4K2K - 30Hz

4K2K - 60Hz

21

7. Cleaning and Troubleshooting

7.1. Cleaning Caution When Using the Display

Do not bring your hands, face or objects close to the ventilation holes of the display. The top of the display is usually very hot due to the high temperature of exhaust air being released through the ventilation holes. Burns or personal injuries may occur if any body parts are brought too close. Placing any object near the top of the display could also result in heat related damage to the object as well as the display itself.

Be sure to disconnect all cables before moving the display. Moving the display with its cables attached may damage the cables and thus cause fire or electric shock.

Disconnect the power plug from the wall outlet as a safety precaution before carrying out any type of cleaning or maintenance procedure.

Front Panel Cleaning Instructions The front of the display has been specially treated. Wipe the surface gently

using only a cleaning cloth or a soft, lint-free cloth. If the surface becomes dirty, soak a soft, lint-free cloth in a mild detergent

solution. Wring the cloth to remove excess liquid. Wipe the surface of the display to remove dirt. Then use a dry cloth of the same type to dry.

Do not scratch or hit the surface of the panel with fingers or hard objects of any kind.

Do not use volatile substances such as insert sprays, solvents and thinners.

Cabinet Cleaning Instructions If the cabinet becomes dirty, wipe the cabinet with a soft, dry cloth. If the cabinet is extremely dirty, soak a lint-free cloth in a mild detergent

solution. Wring the cloth to remove as much moisture as possible. Wipe the cabinet. Use another dry cloth to wipe over until the surface is dry.

Do not use solution that contains oil to clean the plastic parts. Such product damage the plastic parts and void the warranty.

Do not allow any water or detergent to come into contact with the surface of the display. If water or moisture gets inside the unit, operating problems, electrical and shock hazards may result.

Do not scratch or hit the cabinet with fingers or hard objects of any kind. Do not use volatile substances such as insert sprays, solvents and thinners

on the cabinet. Do not place anything made from rubber or PVC near the cabinet for any

extended periods of time.

22

7.2. Troubleshooting

Symptom Possible cause Solution

No display 1. The power cord has been disconnected.

2. The main power switch on the back of the monitor is not turned on.

3. The selected input is not connected.

4. The monitor is in the standby mode.

1. Plug the power cord. 2. Make sure the power switch

is turned on. 3. Link signals to the monitor.

The monitor receives interference or noise can be heard..

This is caused by the surrounding electrical devices or fluorescent light.

Move the monitor to other positions to check if the interference is reduced.

Abnormal color The signal wire is not correctly connected.

Make sure the signal wire is firmly connected to the rear of the monitor.

The display is twisted, and there are abnormal patterns.

1. The signal wire is not correctly connected.

2. The input signal is beyond the capability of the monitor.

1. Make sure the signal wire is firmly connected.

2. Check if the video signal source is beyond the range of the monitor. Please check the specification of the monitor against its specifications.

The displayed picture does not cover the whole screen.

1. The aspect ratio is incorrect. 2. The scanning mode may be

incorrectly set in Underscan. 3. If the picture size exceeds

the screen size, the scanning mode may need to be set to be Underscan.

Use the aspect ratio in the screen menu or the self-set zooming function to tune the geometric shape of the screen and the clock frequency parameter.

There is sound, but no picture.

The input source signal wire is incorrectly connected.

Make sure video input and voice input are both correctly connected.

23

There is picture, but no sound.

1. The input source signal wire is incorrectly connected.

2. The volume is minimized. 3. {Mute} has been enabled. 4. The external loudspeaker

is not connected.

1. Make sure video input and voice input are both correctly connected.

2. Use [ ] or [ ] button to adjust the volume.

3. Use [ ] button to disable Mute.

4. Connect the external loudspeaker and adjust the volume to a proper level.

Some picture elements are dim.

Some pixels on the screen may be not activated.

This monitor is made by very high precision technology. However, sometimes, some pixels on the monitor may still be not displayed. This is not a failure.

There is picture retention on the monitor display after the monitor is powered off. (Examples of motionless pictures include: icon, video game, computer image, and pictures displayed in 4:3 standard mode.)

Too long display of the motionless picture

Never display the motionless picture for a long time, or the monitor will have permanent picture retention.

24

8. Technical specification

Item Specification

50 55 65

Screen size (effective area)

49.5 inch (126 cm) diagonal line LCD

54.6 inch (138.7 cm) diagonal line LCD

64.5 inch (163.9 cm) diagonal line LCD

Aspect ratio 16:9 16:9 16:9

Pixel number 3840 (H) x 2160 (V) 3840 (H) x 2160 (V) 3840 (H) x 2160 (V)

Dot Spacing 0.2854 (H) x 0.2854 (V) [mm]

0.315 (H) x 0.315 (V) [mm]

0.372 (H) x 0.372 (V) [mm]

Displayable color 8bits+FRC 1.07G Color

8bits+FRC 1.07G Color

8bits+FRC 1.07G Color

Brightness (classic) 300 cd/m2 (classic) 350 cd/m2 (classic) 350 cd/m2 (classic)

Contrast (classic) 5000:1 1200:1 1200:1

Visual angle 178 (Typ.) 178 (Typ.) 178 (Typ.)

Input/output terminal: Item Specification Loudspeaker output

Internal loudspeaker 7 W (L) + 7 W (R) [RMS]/6

Audio input 3.5Mm Headphone jack x 1 0.5V [rms]( normal mode) / 2 sound track (L+R)

VGA input D-SUB jack (15pin) Analog RGB: 0.7V [p-p] (75), H/CS/V: TTL (2.2k), MAX: 1920 x 1080/60 Hz (WUXGA)

HDMI input HDMI interface x 2 (A type) (19 pins)

Digit RGB: TMDS (video + audio setting) Max.: Video HDMI 1 4K@30Hz HDMI 2 4K@60Hz

Audio - 48 KHz/ 2 sound track (L+R) Support LPCM only

USB input USB2.0 A type x1 USB2.0

RS232 RJ-45 Jack x 1 (8 pin) RS232 in

25

General:

Item Specification

50 55 65

Power input 100-240V~, 50/60Hz

100-240V~, 50/60Hz

100-240V~, 50/60Hz

Power consumption (max.)

110 W 145 W 190 W

Power consumption (classic)

90 W 115 W 160 W

Power consumption (standby and power-off)

<0.5 W <0.5 W <0.5 W

Dimension (without base) [W x H x D]

1113.0 X 649.0 X 87.2 mm

1222.8 X 713.39 X 85.55 mm

1449.6 X 844.7 X 78.6 mm

Dimension (with base) [W x H x D]

1113.0 X 710.5 X 247.9 mm

1222.8 X 786.86 X 268.87mm

1449.6 X 883.4 X 283.4 mm

Net weight (without base) 10.41 Kg 11.18 Kg 18.6 Kg

Net weight (with base) 10.65 Kg 11.42 Kg 18.75 Kg

Environmental conditions: Item Specification Temperature Running 0 ~ 40

Storage -20 ~ 60

Temperature Running 20 ~ 80% RH (no dew)

Storage 10 ~ 90% RH (no dew)

Altitude Running 0 ~ 3,000 m

Storage/transport 0 ~ 9,000 m

Manualsnet FAQs

If you want to find out how the DS-D5050UC-C Hikvision works, you can view and download the Hikvision DS-D5050UC-C Monitor User's Manual on the Manualsnet website.

Yes, we have the User's Manual for Hikvision DS-D5050UC-C as well as other Hikvision manuals. All you need to do is to use our search bar and find the user manual that you are looking for.

The User's Manual should include all the details that are needed to use a Hikvision DS-D5050UC-C. Full manuals and user guide PDFs can be downloaded from Manualsnet.com.

The best way to navigate the Hikvision DS-D5050UC-C Monitor User's Manual is by checking the Table of Contents at the top of the page where available. This allows you to navigate a manual by jumping to the section you are looking for.

This Hikvision DS-D5050UC-C Monitor User's Manual consists of sections like Table of Contents, to name a few. For easier navigation, use the Table of Contents in the upper left corner.

You can download Hikvision DS-D5050UC-C Monitor User's Manual free of charge simply by clicking the “download” button in the upper right corner of any manuals page. This feature allows you to download any manual in a couple of seconds and is generally in PDF format. You can also save a manual for later by adding it to your saved documents in the user profile.

To be able to print Hikvision DS-D5050UC-C Monitor User's Manual, simply download the document to your computer. Once downloaded, open the PDF file and print the Hikvision DS-D5050UC-C Monitor User's Manual as you would any other document. This can usually be achieved by clicking on “File” and then “Print” from the menu bar.