Regulatory Information FCC Informaon Please take aenon that changes or modificaon not expressly approved by the party responsible for compliance could void the users authority to operate the equipment. FCC compliance: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protecon against harmful interference in a residenal installaon. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instrucons, may cause harmful interference to radio communicaons. However, there is no guarantee that interference will not occur in a parcular installaon. If this equipment does cause harmful interference to radio or television recepon, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: Reorient or relocate the receiving antenna. Increase the separaon between the equipment and receiver. Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. Consult the dealer or an experienced radio/TV technician for help. This equipment should be installed and operated with a minimum distance 20cm between the radiator and your body. FCC Condions This device complies with part 15 of the FCC Rules. Operaon is subject to the following two condions: 1. This device may not cause harmful interference. 2. This device must accept any interference received, including interference that may cause undesired operaon.
2006/66/EC (baery direcve): This product contains a baery that cannot be disposed of as unsorted municipal waste in the European Union. See the product documentaon for specific baery informaon. The baery is marked with this symbol, which may include leering to indicate cadmium (Cd), lead (Pb), or mercury (Hg). For proper recycling, return the baery to your supplier or to a designated collecon point. For more informaon see: www.recyclethis.info
2012/19/EU (WEEE direcve): Products marked with this symbol cannot be disposed of as unsorted municipal waste in the European Union. For proper recycling, return this product to your local supplier upon the purchase of equivalent new equipment, or dispose of it at designated collecon points. For more informaon see: www.recyclethis.info
This product and - if applicable - the supplied accessories too are marked with "CE" and comply therefore with the applicable harmonized European standards listed under the RE Direcve 2014/53/EU, the EMC Direcve 2014/30/EU, the RoHS Direcve 2011/65/EU.
Warning In the use of the product, you must be in strict compliance with the electrical safety regulaons of the naon and region. CAUTION: To reduce the risk of fire, replace only with the same type and rang of fuse. CAUTION: This equipment is for use only with Hikvisions bracket. Use with other (carts, stands, or carriers) may result in instability causing injury. To prevent possible hearing damage, do not listen at high volume levels for long periods. Please use the power adapter, which is provided by normal company. The power consumpon cannot be less than the required value. Do not connect several devices to one power adapter as adapter overload may cause over- heat or fire hazard. Please make sure that the power has been disconnected before you wire, install or dismantle the device. When the product is installed on wall or ceiling, the device shall be firmly fixed. If smoke, odors or noise rise from the device, turn off the power at once and unplug the power cable, and then please contact the service center. If the product does not work properly, please contact your dealer or the nearest service center. Never aempt to disassemble the device yourself. (We shall not assume any responsibility for problems caused by unauthorized repair or maintenance.)
Cauon + idenfies the posive terminal(s) of equipment which is used with, or generates direct current. + idenfies the negave terminal(s) of equipment which is used with, or generates direct current. No naked flame sources, such as lighted candles, should be placed on the equipment. The USB port of the equipment is used for connecng to a USB flash drive only. The serial port of the equipment is used for debugging only. Burned fingers when handling the fingerprint sensor metal. Wait one-half hour aer switching off before handling the parts. Install the equipment according to the instrucons in this manual. To prevent injury, this equipment must be securely aached to the floor/wall in accordance with the installaon instrucons. Do not drop the device or subject it to physical shock, and do not expose it to high electromagnesm radiaon. Avoid the equipment installaon on vibraons surface or places subject to shock (ignorance can cause equipment damage). Do not place the device in extremely hot (refer to the specificaon of the device for the detailed operang temperature), cold, dusty or damp locaons, and do not expose it to high electromagnec radiaon. The device cover for indoor use shall be kept from rain and moisture. Exposing the equipment to direct sun light, low venlaon or heat source such as heater or radiator is forbidden (ignorance can cause fire danger). Do not aim the device at the sun or extra bright places. A blooming or smear may occur otherwise (which is not a malfuncon however), and affecng the endurance of sensor at the same me. Please use the provided glove when open up the device cover, avoid direct contact with the device cover, because the acidic sweat of the fingers may erode the surface coang of the device cover. Please use a so and dry cloth when clean inside and outside surfaces of the device cover, do not use alkaline detergents. Please keep all wrappers aer unpack them for future use. In case of any failure occurred, you need to return the device to the factory with the original wrapper. Transportaon without the original wrapper may result in damage on the device and lead to addional costs. Improper use or replacement of the baery may result in hazard of explosion. Replace with the same or equivalent type only. Dispose of used baeries according to the instrucons provided by the baery manufacturer. Biometric recognion products cannot be completely applicable to an-spoofing environments. If you require a higher security level, use mulple authencaon modes. Please make sure that the biometric recognion accuracy will be affected by the collected pictures' quality and the light in the environment, which cannot be completely correct.
1 2 3
4 5 6
WallDevice Gang Box
After wiring, you should apply Silicone sealant among the joint.
Rear Panel
Mounting Ear WallScrews Wall
Wall Set Screw
Apply Silicone sealant among the joints between the device and the wall (except the lower side) to keep the raindrop from entering.
Cave an installation hole on the wall. Pull the cable out from the wall. Remove the mounting ears of
the gang box.
Fix the sub module to the door station with 2 set screws. Wire the device and cover the rear panel with 2 screws.
Insert the door station into the gang box. Fix door station to the gang box with set screw.
Install the gang box into the wall. a. Insert the gang box into the installation hole. Mark the gang box marker, and take out the gang box. b. Drill 4 screw holes according to the marks on the wall, and insert the expansion sleeves into the screw holes. c. Fix the gang box with 4 screws.
The suggested dimension of the installation hole is 138.3 mm (W) 335.7 mm (H) 41.3 mm (D). The suggested length of the cables left outside is 250 mm.
Flush MountingSurface Mounting
3
Splice Set Screws
Splice Set Screws
Wall
Fix the device to the mounting plate and fix the device with the set screws.
WallMounting Template
2
Set Screw
Fix the mounting plate to the wall with 4 supplied screws.
Wire the device and cover the rear panel with 2 screws. Apply Silicone sealant among the joints.
Paste the mounting template on the wall according to the installation requirements. Drill holes acording to the template. Insert the expansion bolts into the
en
