Hikvision DS-KDM9403-FKP Module Quick Start Guide PDF

1 of 2
1 of 2

Summary of Content for Hikvision DS-KDM9403-FKP Module Quick Start Guide PDF

Quick Start Guide

UD27987B

Sub Module of Door Station

2022 Hangzhou Hikvision Digital Technology Co., Ltd. All rights reserved. About this Manual The Manual includes instructions for using and managing the Product. Pictures, charts, images and all other information hereinafter are for description and explanation only. The information contained in the Manual is subject to change, without notice, due to firmware updates or other reasons. Please find the latest version of this Manual at the Hikvision website (https:// www.hikvision.com/). Please use this Manual with the guidance and assistance of professionals trained in supporting the Product. Trademarks

and other Hikvision's trademarks and logos are the properties of Hikvision in various jurisdictions. Other trademarks and logos mentioned are the properties of their respective owners. Disclaimer TO THE MAXIMUM EXTENT PERMITTED BY APPLICABLE LAW, THIS MANUAL AND THE PRODUCT DESCRIBED, WITH ITS HARDWARE, SOFTWARE AND FIRMWARE, ARE PROVIDED AS IS AND WITH ALL FAULTS AND ERRORS. HIKVISION MAKES NO WARRANTIES, EXPRESS OR IMPLIED, INCLUDING WITHOUT LIMITATION, MERCHANTABILITY, SATISFACTORY QUALITY, OR FITNESS FOR A PARTICULAR PURPOSE. THE USE OF THE PRODUCT BY YOU IS AT YOUR OWN RISK. IN NO EVENT WILL HIKVISION BE LIABLE TO YOU FOR ANY SPECIAL, CONSEQUENTIAL, INCIDENTAL, OR INDIRECT DAMAGES, INCLUDING, AMONG OTHERS, DAMAGES FOR LOSS OF BUSINESS PROFITS, BUSINESS INTERRUPTION, OR LOSS OF DATA, CORRUPTION OF SYSTEMS, OR LOSS OF DOCUMENTATION, WHETHER BASED ON BREACH OF CONTRACT, TORT (INCLUDING NEGLIGENCE), PRODUCT LIABILITY, OR OTHERWISE, IN CONNECTION WITH THE USE OF THE PRODUCT, EVEN IF HIKVISION HAS BEEN ADVISED OF THE POSSIBILITY OF SUCH DAMAGES OR LOSS. YOU ACKNOWLEDGE THAT THE NATURE OF INTERNET PROVIDES FOR INHERENT SECURITY RISKS, AND HIKVISION SHALL NOT TAKE ANY RESPONSIBILITIES FOR ABNORMAL OPERATION, PRIVACY LEAKAGE OR OTHER DAMAGES RESULTING FROM CYBER-ATTACK, HACKER ATTACK, VIRUS INSPECTION, OR OTHER INTERNET SECURITY RISKS; HOWEVER, HIKVISION WILL PROVIDE TIMELY TECHNICAL SUPPORT IF REQUIRED. YOU AGREE TO USE THIS PRODUCT IN COMPLIANCE WITH ALL APPLICABLE LAWS, AND YOU ARE SOLELY RESPONSIBLE FOR ENSURING THAT YOUR USE CONFORMS TO THE APPLICABLE LAW. ESPECIALLY, YOU ARE RESPONSIBLE, FOR USING THIS PRODUCT IN A MANNER THAT DOES NOT INFRINGE ON THE RIGHTS OF THIRD PARTIES, INCLUDING WITHOUT LIMITATION, RIGHTS OF PUBLICITY, INTELLECTUAL PROPERTY RIGHTS, OR DATA PROTECTION AND OTHER PRIVACY RIGHTS. YOU SHALL NOT USE THIS PRODUCT FOR ANY PROHIBITED END-USES, INCLUDING THE DEVELOPMENT OR PRODUCTION OF WEAPONS OF MASS DESTRUCTION, THE DEVELOPMENT OR PRODUCTION OF CHEMICAL OR BIOLOGICAL WEAPONS, ANY ACTIVITIES IN THE CONTEXT RELATED TO ANY NUCLEAR EXPLOSIVE OR UNSAFE NUCLEAR FUEL-CYCLE, OR IN SUPPORT OF HUMAN RIGHTS ABUSES. IN THE EVENT OF ANY CONFLICTS BETWEEN THIS MANUAL AND THE APPLICABLE LAW, THE LATER PREVAILS.

Data Protecon During the use of device, personal data will be collected, stored and processed. To protect data, the development of Hikvision devices incorporates privacy by design principles. For example, for device with facial recognion features, biometrics data is stored in your device with encrypon method; for fingerprint device, only fingerprint template will be saved, which is impossible to reconstruct a fingerprint image. As data controller, you are advised to collect, store, process and transfer data in accordance with the applicable data protecon laws and regulaons, including without limitaon, conducng security controls to safeguard personal data, such as, implemenng reasonable administrave and physical security controls, conduct periodic reviews and assessments of the effecveness of your security controls.

Appearance1

23 3

18 0

83 .5

11

80

4

2 60

112.4 21 128.4 40.8

31 2. 9

Unit:mmUnit:mm

Mounting Plate The dimension of the mounting plate is 233 mm (H) 112.4 mm (W) 21 mm (D).

Gang Box The dimension of the gang box is 312.9 mm (H) 128.4 mm (W) 40.8 mm (D). The installation hole should be bigger than the actual size. The suggested dimension of the installation hole is 313.5 mm (H) 128.9 mm (W) 41.3 mm (D).

Installation2

The sub modules should be installed to the face recognition door station. The installation method of two sub modules are the same. There takes fingerprint module's installation for example.

Product Model Fingerprint Module DS-KDM9403-FKP Keypad Module DS-KDM9403-KP

145 mm 28 mm

76 m m

145 mm 28 mm

76 m m

Fingerprint ModuleKeypad Module

Regulatory Information FCC Informaon Please take aenon that changes or modificaon not expressly approved by the party responsible for compliance could void the users authority to operate the equipment. FCC compliance: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protecon against harmful interference in a residenal installaon. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instrucons, may cause harmful interference to radio communicaons. However, there is no guarantee that interference will not occur in a parcular installaon. If this equipment does cause harmful interference to radio or television recepon, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: Reorient or relocate the receiving antenna. Increase the separaon between the equipment and receiver. Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. Consult the dealer or an experienced radio/TV technician for help. This equipment should be installed and operated with a minimum distance 20cm between the radiator and your body. FCC Condions This device complies with part 15 of the FCC Rules. Operaon is subject to the following two condions: 1. This device may not cause harmful interference. 2. This device must accept any interference received, including interference that may cause undesired operaon.

2006/66/EC (baery direcve): This product contains a baery that cannot be disposed of as unsorted municipal waste in the European Union. See the product documentaon for specific baery informaon. The baery is marked with this symbol, which may include leering to indicate cadmium (Cd), lead (Pb), or mercury (Hg). For proper recycling, return the baery to your supplier or to a designated collecon point. For more informaon see: www.recyclethis.info

2012/19/EU (WEEE direcve): Products marked with this symbol cannot be disposed of as unsorted municipal waste in the European Union. For proper recycling, return this product to your local supplier upon the purchase of equivalent new equipment, or dispose of it at designated collecon points. For more informaon see: www.recyclethis.info

This product and - if applicable - the supplied accessories too are marked with "CE" and comply therefore with the applicable harmonized European standards listed under the RE Direcve 2014/53/EU, the EMC Direcve 2014/30/EU, the RoHS Direcve 2011/65/EU.

Warning In the use of the product, you must be in strict compliance with the electrical safety regulaons of the naon and region. CAUTION: To reduce the risk of fire, replace only with the same type and rang of fuse. CAUTION: This equipment is for use only with Hikvisions bracket. Use with other (carts, stands, or carriers) may result in instability causing injury. To prevent possible hearing damage, do not listen at high volume levels for long periods. Please use the power adapter, which is provided by normal company. The power consumpon cannot be less than the required value. Do not connect several devices to one power adapter as adapter overload may cause over- heat or fire hazard. Please make sure that the power has been disconnected before you wire, install or dismantle the device. When the product is installed on wall or ceiling, the device shall be firmly fixed. If smoke, odors or noise rise from the device, turn off the power at once and unplug the power cable, and then please contact the service center. If the product does not work properly, please contact your dealer or the nearest service center. Never aempt to disassemble the device yourself. (We shall not assume any responsibility for problems caused by unauthorized repair or maintenance.)

Cauon + idenfies the posive terminal(s) of equipment which is used with, or generates direct current. + idenfies the negave terminal(s) of equipment which is used with, or generates direct current. No naked flame sources, such as lighted candles, should be placed on the equipment. The USB port of the equipment is used for connecng to a USB flash drive only. The serial port of the equipment is used for debugging only. Burned fingers when handling the fingerprint sensor metal. Wait one-half hour aer switching off before handling the parts. Install the equipment according to the instrucons in this manual. To prevent injury, this equipment must be securely aached to the floor/wall in accordance with the installaon instrucons. Do not drop the device or subject it to physical shock, and do not expose it to high electromagnesm radiaon. Avoid the equipment installaon on vibraons surface or places subject to shock (ignorance can cause equipment damage). Do not place the device in extremely hot (refer to the specificaon of the device for the detailed operang temperature), cold, dusty or damp locaons, and do not expose it to high electromagnec radiaon. The device cover for indoor use shall be kept from rain and moisture. Exposing the equipment to direct sun light, low venlaon or heat source such as heater or radiator is forbidden (ignorance can cause fire danger). Do not aim the device at the sun or extra bright places. A blooming or smear may occur otherwise (which is not a malfuncon however), and affecng the endurance of sensor at the same me. Please use the provided glove when open up the device cover, avoid direct contact with the device cover, because the acidic sweat of the fingers may erode the surface coang of the device cover. Please use a so and dry cloth when clean inside and outside surfaces of the device cover, do not use alkaline detergents. Please keep all wrappers aer unpack them for future use. In case of any failure occurred, you need to return the device to the factory with the original wrapper. Transportaon without the original wrapper may result in damage on the device and lead to addional costs. Improper use or replacement of the baery may result in hazard of explosion. Replace with the same or equivalent type only. Dispose of used baeries according to the instrucons provided by the baery manufacturer. Biometric recognion products are not 100% applicable to an-spoofing environments. If you require a higher security level, use mulple authencaon modes. Please make sure that the biometric recognion accuracy will be affected by the collected pictures' quality and the light in the environment, which cannot be 100% correct.

Flush Mounting

Surface Mounting

1 23

Set Screw

Splice Set Screw

Screws Mounting Plate Mounting Template Wall

Set Screw Door Station Screws Gang Box Wall

1 23

1

2

3

Paste the mounting template on the wall according to the installation requirements. Drill holes acording to the template. Insert the expansion bolts into the screw holes. Fix the mounting plate to the wall with 4 supplied screws. Wire the device and cover the rear panel with 2 screws. Fix the device to the mounting plate and fix the device with the set screws. Fix the sub module to the door station with 2 set screws.

Do not touch the TF card slot and other devices during the process of plugging in and unplugging the power interface. Apply Silicone sealant among the joints between the device and the wall (except the lower side) to keep the raindrop from entering.

Do not touch the TF card slot and other devices during the process of plugging in and unplugging the power interface. Apply Silicone sealant among the joints between the device and the wall (except the lower side) to keep the raindrop from entering.

Cave an installation hole on the wall. Pull the cable out from the wall.

Install the gang box into the wall. a. Insert the gang box into the installation hole. Mark the gang box screw holes position with a marker, and take out the gang box. b. Drill 4 screw holes according to the marks on the wall, and insert the expansion sleeves into the screw holes. c. Fix the gang box with 4 screws. d. Remove the mounting ears of the gang box. Fix the sub module to the door station with 2 set screws. Wire the device and cover the rear panel with 2 screws. Insert the door station into the gang box and fix it with set screw.

T

Manualsnet FAQs

If you want to find out how the DS-KDM9403-FKP Hikvision works, you can view and download the Hikvision DS-KDM9403-FKP Module Quick Start Guide on the Manualsnet website.

Yes, we have the Quick Start Guide for Hikvision DS-KDM9403-FKP as well as other Hikvision manuals. All you need to do is to use our search bar and find the user manual that you are looking for.

The Quick Start Guide should include all the details that are needed to use a Hikvision DS-KDM9403-FKP. Full manuals and user guide PDFs can be downloaded from Manualsnet.com.

The best way to navigate the Hikvision DS-KDM9403-FKP Module Quick Start Guide is by checking the Table of Contents at the top of the page where available. This allows you to navigate a manual by jumping to the section you are looking for.

This Hikvision DS-KDM9403-FKP Module Quick Start Guide consists of sections like Table of Contents, to name a few. For easier navigation, use the Table of Contents in the upper left corner.

You can download Hikvision DS-KDM9403-FKP Module Quick Start Guide free of charge simply by clicking the “download” button in the upper right corner of any manuals page. This feature allows you to download any manual in a couple of seconds and is generally in PDF format. You can also save a manual for later by adding it to your saved documents in the user profile.

To be able to print Hikvision DS-KDM9403-FKP Module Quick Start Guide, simply download the document to your computer. Once downloaded, open the PDF file and print the Hikvision DS-KDM9403-FKP Module Quick Start Guide as you would any other document. This can usually be achieved by clicking on “File” and then “Print” from the menu bar.