3. Secure the mounting plate on the wall with four supplied
4. Rotate the keypad body clockwise to fasten the body on the
1. Loosen the set screws on bottom of the keypad. 2. Rotate anti-clockwise to remove the mounting plate.
It is required to insert the screw for tamper alarm.
5. Tighten the screw on the bottom to x the keypad on the mounting plate and complete the installation.
COPYRIGHT 2019 Hangzhou Hikvision Digital Technology Co., Ltd. ALL RIGHTS RESERVED. Any and all information, including, among others, wordings, pictures, graphs are the properties of Hangzhou Hikvision Digital Technology Co., Ltd. or its subsidiaries (hereinafter referred to be Hikvision). This user manual (hereinafter referred to be the Manual) cannot be reproduced, changed, translated, or distributed, partially or wholly, by any means, without the prior written permission of Hikvision. Unless otherwise stipulated, Hikvision does not make any warranties, guarantees or representations, express or implied, regarding to the Manual. About this Manual This Manual is applicable to Alarm Keypad. The Manual includes instructions for using and managing the product. Pictures, charts, images and all other information hereinafter are for description and explanation only. The information contained in the Manual is subject to change, without notice, due to rmware updates or other reasons. Please nd the latest version in the company website (http://overseas.hikvision.com/en/). Please use this user manual under the guidance of professionals.
Legal Disclaimer TO THE MAXIMUM EXTENT PERMITTED BY APPLICABLE LAW, THE PRODUCT DESCRIBED, WITH ITS HARDWARE, SOFTWARE AND FIRMWARE, IS PROVIDED AS IS, WITH ALL FAULTS AND ERRORS, AND HIKVISION MAKES NO WARRANTIES, EXPRESS OR IMPLIED, INCLUDING WITHOUT LIMITATION, MERCHANTABILITY, SATISFACTORY QUALITY, FITNESS FOR A PARTICULAR PURPOSE, AND NON-INFRINGEMENT OF THIRD PARTY. IN NO EVENT WILL HIKVISION, ITS DIRECTORS, OFFICERS, EMPLOYEES, OR AGENTS BE LIABLE TO YOU FOR ANY SPECIAL, CONSEQUENTIAL, INCIDENTAL, OR INDIRECT DAMAGES, INCLUDING, AMONG OTHERS, DAMAGES FOR LOSS OF BUSINESS PROFITS, BUSINESS INTERRUPTION, OR LOSS OF DATA OR
Trademarks Acknowledgement and other Hikvisions trademarks and logos are the properties of Hikvision in various jurisdictions. Other trademarks and logos mentioned below are the properties of their respective owners.
DOCUMENTATION, IN CONNECTION WITH THE USE OF THIS PRODUCT, EVEN IF HIKVISION HAS BEEN ADVISED OF THE POSSIBILITY OF SUCH DAMAGES. REGARDING TO THE PRODUCT WITH INTERNET ACCESS, THE USE OF PRODUCT SHALL BE WHOLLY AT YOUR OWN RISKS. HIKVISION SHALL NOT TAKE ANY RESPONSIBILITES FOR ABNORMAL OPERATION, PRIVACY LEAKAGE OR OTHER DAMAGES RESULTING FROM CYBER ATTACK, HACKER ATTACK, VIRUS INSPECTION, OR OTHER INTERNET SECURITY RISKS; HOWEVER, HIKVISION WILL PROVIDE TIMELY TECHNICAL SUPPORT IF REQUIRED. SURVEILLANCE LAWS VARY BY JURISDICTION. PLEASE CHECK ALL RELEVANT LAWS IN YOUR JURISDICTION BEFORE USING THIS PRODUCT IN ORDER TO ENSURE THAT YOUR USE CONFORMS THE APPLICABLE LAW. HIKVISION SHALL NOT BE LIABLE IN THE EVENT THAT THIS PRODUCT IS USED WITH ILLEGITIMATE PURPOSES. IN THE EVENT OF ANY CONFLICTS BETWEEN THIS MANUAL AND THE APPLICABLE LAW, THE LATER PREVAILS.
Enrollment
English
Diagram Reference
Product Information
Specification
Components and Indication1
3
Installation4
Operation5
Power On2
1
2 4
5
3
Wireless Alarm Keypad
This product and - if applicable - the supplied accessories too are marked with "CE" and comply therefore with the applicable harmonized European standards listed under the RE Directive 2014/53/EU, the EMC Directive 2014/30/EU, the LVD Directive 2014/35/EU, the RoHS Directive 2011/65/EU.
2012/19/EU (WEEE directive): Products marked with this symbol cannot be disposed of as unsorted municipal waste in the European Union. For proper recycling, return this product to your local supplier upon the purchase of equivalent new equipment, or dispose of it at designated collection points. For more information see: www.recyclethis.info
The Input voltage should meet both the SELV (Safety Extra Low Voltage) and the Limited Power Source according to the IEC60950-1 standard. Please refer to technical specications for detailed information.
Tamper Screw
1 2 3
4 5
2
3
1
1
3
21
Control Panel
Power on the security control panel. Make the control panel enter the enrollment mode. Press the tamper switch (on the board) of the keypad. The partition indicators ashes 4 times when the keypad is enrolled and ready for work. Note: The distance between the security control panel and the keypad should be less than 50 cm.
1. Loosen the set screws on bottom of the keypad. 2. Remove the mounting plate. 3. Install four AA batteries according to the polarity mark. Note: Do not reverse the polarity of the battery.
Check Signal Strength Enter the signal checking mode by operating on the control panel. Trigger the tamper alarm. Power indicator ashes 3 times - Strong Signal Fault indicator ashes 3 times - Weak Signal
Buzzer
1. Indicator
2. Tag Area 3. TAMPER Switch (on the board)
Power IndicatorGreen
Blue
Orange
Red
Keypad Backlight White Keypad locked: flashes 2 times Turn off if no operation for 5 s, turn on when touched
Normal Battery: Solid green for 2s (keypad waked up) Low BatteryFlashing green flashes 3 times (keypad waked up)
Weak Signal StrengthFlashes 3 times
Strong Signal StrengthFlashes 3 times Armed: Related LED flashes once, and light on 2 s while
the keypad is waked up Disarmed/Alarm Cleared:Related LED flashes twice Operation failed: Related LED flashes 3 times Alarm: Related LED flashes 30s Enrolled and Strats work: 4 LEDs flashes 4 times together
Patrol card presented: Power and Fault LEDs flashes 2 times
Patrol card presented: Power and Fault LEDs flashes 2 times
Zone/ Fire Alarm TriggeredFlashes 30s No Alarm or Alarm RestoredOff
Partition Indicator
Fault Indicator Alarm Indicator
Present Tag/Tap Key/Armed
Disarmed
Operation Failed Keypad Tampered
Card Enrolled
Zone Tampered
Fire Alarm
Beep Beep Beep Beep Beep Beep Beep Beep
Beep
Beep
Long Beep (30 s)
Long Beep (30 s)
Beep Beep
Formatting Remove the battery. Hold the TAMPER button (with slend rod) and power the keypad on at the same time. The power, alarm, fault indicators ashes 4 time after the formatting is completed.
Operation
All Partition 1 Enter the user password. 2. Tab the stay/away/disarm key.
Specified Partition
1. Tab the user password. 2. Tab the key. 3. Enter the partition No.(1/2/3/4). 4. Tab the stay/away/disarm key.
Partition Keypad
Fire Alarm
Panic Alarm Confirm
Tasks
1.Enter the user password.
2.Tab the stay/away/disarm key.
Stay/Away Arming Disarming
Global Keypad
Hold the fire alarm key for 3 s.
Hold the disarming key for 3 s. Tab the key.
RF speed 10.0kbps/4.8bps RF frequency 433MHz/868MHz RF method 2GFSK Transmission distance 800m (open area) Power 10dBm Tamper-proof 1 tamper swtch, front and rear tamper-proof Wireless Module Communicates with control panel Tag reader Supports standard IC card Buzzer 1 Serial port 1, reserved
Indicator 3 status indicators: power (green), fault (orange), and alarm (red) 4 partition indicators: armed/disarmed (blue)
Backlight 1 group Numeric key 10, 0 to 9 Function key 6, re, away arming, stay arming, diarming, deleting, and OK
Electrical & Battery Power 4 AA Batteries3V DC 3 years standby Operation humidity 10 to 90 Operation temperature 10 to +55 Color White/Black Installation Wall mounting with screws
Wireless Keypad
RF
Interface and Component
Others
Do not mix batteries of dierent brands. Do not mix old and new batteries.
EN50131-1:2006+A2:2017 EN50131-3:2009E N50131-5-3:2017 Security Grade 2 Environmental Class II
1. Log in to the APP Store. Search for Hik-Connect .Download and install the client to your phone. Run the client. 2. Power on the security control panel. 3. Log in the client and tap the icon + to add the ontrol panel. Scan the QR code or input the device serial No. to add the device( in the registration mode). 4. Tap the + icon on the device page to add the peripherals. .
Local Enrollment APP Enrollment
Present
Beep
Tag Sensed Present Remove
Beep
Tag Sensed Hold 3s,
remove after a beep
1
2
Present
Beep
Tag Sensed
3 System Armed
Remove
Operating illegal tag (unregistered tag) more than 3 t
en
