Hikvision DS-K2601-G Controller Quick Start Guide PDF

1 of 2
1 of 2

Summary of Content for Hikvision DS-K2601-G Controller Quick Start Guide PDF

N O

LED-A

LED1

LED2

LED-B LED-C LED-D

N C

NO NC

RS-485 Communication Indicator

Alarm Output Indicator

Battery Charging Indicator

Running Indicator DIP Switch

Charging Completed Indicator

Power Indicator

Network Data Indicator

Network Status Indicator

Alarm Input

N etw

ork Interface

Door Contact Input Exit Button

Ev en

t In

pu t

Ev en

t In

pu t

Lock1 Lock2 Lock3 Lock4

NORMAL INITIAL

Z4 D 1+

D 1-

D 2+

D 2-

D 3+

D 3-

D 4+

D 4-

S1 B1 G N

D B2 B3 G

N D

B4

C8

+12 V

GND

BAT+

BAT-

RS-485A+ RS-485A-

GND

RS-485B+ RS-485B-

GND

RS-485C+ RS-485C-

GND

RS-485D+ RS-485D-

GND

NO/NC1 COM1

NO/NC2 COM2

NO/NC3 COM3

NO/NC4 COM4

G N

D +

12 V

G N

D

+ 12

V

G N

D W

0 W

1

BZ ER R

O K

G N

D W

0 W

1

BZ ER R

O K

G N

D W

0 W

1

BZ ER R

O K

G N

D W

0 W

1

BZ ER R

O K

GND C7 C6 GND C5

C4 GND C3 C2 GND C1

G N

D

S2 S3 G N

D S4G

N D

Z3Z2G N

D

Z1

Lock Power

Reader Power Wiegand Reader 4 Wiegand Reader 3 Wiegand Reader 1Wiegand Reader 2

Pow er

Supply Battery

R S-485 Reader

U plink R

S-485 A

larm O

utput

Access Controller

Quick Start Guide

UD17322B-A

COPYRIGHT 2019 Hangzhou Hikvision Digital Technology Co., Ltd. ALL RIGHTS RESERVED. Any and all information, including, among others, wordings, pictures, graphs are the properties of Hangzhou Hikvision Digital Technology Co., Ltd. or its subsidiaries (hereinafter referred to be Hikvision). This user manual (hereinafter referred to be the Manual) cannot be reproduced, changed, translated, or distributed, partially or wholly, by any means, without the prior written permission of Hikvision. Unless otherwise stipulated, Hikvision does not make any warranties, guarantees or representations, express or implied, regarding to the Manual. About this Manual The Manual includes instructions for using and managing the product. Pictures, charts, images and all other information hereinafter are for description and explanation only. The information contained in the Manual is subject to change, without notice, due to firmware updates or other reasons. Please find the latest version in the company website (http://overseas.hikvi- sion.com/en/). Please use this user manual under the guidance of professionals. Trademarks Acknowledgement and other Hikvisions trademarks and logos are the properties of Hikvision in various jurisdictions. Other trademarks and logos mentioned below are the properties of their respective owners. Legal Disclaimer TO THE MAXIMUM EXTENT PERMITTED BY APPLICABLE LAW, THE PRODUCT DESCRIBED, WITH ITS HARDWARE, SOFTWARE AND FIRMWARE, IS PROVIDED AS IS, WITH ALL FAULTS AND ERRORS, AND HIKVISION MAKES NO WARRANTIES, EXPRESS OR IMPLIED, INCLUDING WITHOUT LIMITATION, MERCHANTABILITY, SATISFACTORY QUALITY, FITNESS FOR A PARTICULAR PURPOSE, AND NON-INFRINGEMENT OF THIRD PARTY. IN NO EVENT WILL HIKVISION, ITS DIRECTORS, OFFICERS, EMPLOYEES, OR AGENTS BE LIABLE TO YOU FOR ANY SPECIAL, CONSEQUENTIAL, INCIDENTAL, OR INDIRECT DAMAGES, INCLUDING, AMONG OTHERS, DAMAGES FOR LOSS OF BUSINESS PROFITS, BUSINESS INTERRUPTION, OR LOSS OF DATA OR DOCUMENTATION, IN CONNECTION WITH THE USE OF THIS PRODUCT, EVEN IF HIKVISION HAS BEEN ADVISED OF THE POSSIBILITY OF SUCH DAMAGES. REGARDING TO THE PRODUCT WITH INTERNET ACCESS, THE USE OF PRODUCT SHALL BE WHOLLY AT YOUR OWN RISKS. HIKVISION SHALL NOT TAKE ANY RESPONSIBILITES FOR ABNORMAL OPERATION, PRIVACY LEAKAGE OR OTHER DAMAGES RESULTING FROM CYBER ATTACK, HACKER ATTACK, VIRUS INSPECTION, OR OTHER INTERNET SECURITY RISKS; HOWEVER, HIKVISION WILL PROVIDE TIMELY TECHNICAL SUPPORT IF REQUIRED. SURVEILLANCE LAWS VARY BY JURISDICTION. PLEASE CHECK ALL RELEVANT LAWS IN YOUR JURISDICTION BEFORE USING THIS PRODUCT IN ORDER TO ENSURE THAT YOUR USE CONFORMS THE APPLICABLE LAW. HIKVISION SHALL NOT BE LIABLE IN THE EVENT THAT THIS PRODUCT IS USED WITH ILLEGITIMATE PURPOSES. IN THE EVENT OF ANY CONFLICTS BETWEEN THIS MANUAL AND THE APPLICABLE LAW, THE LATER PREVAILS. Data Protection During the use of device, personal data will be collected, stored and processed. To protect data, the development of Hikvision devices incorporates privacy by design principles. For example, for device with facial recognition features, biometrics data is stored in your device with encryption method; for fingerprint device, only fingerprint template will be saved, which is impossible to reconstruct a fingerprint image. As data controller, you are advised to collect, store, process and transfer data in accordance with the applicable data protection laws and regulations, including without limitation, conducting security controls to safeguard personal data, such as, implementing reasonable administrative and physical security controls, conduct periodic reviews and assessments of the effectiveness of your security controls.

Br ow

n

O ra

ng e

Pu rp

le

W hi

te

G re

en

Bl ac

k

Card ReaderCard ReaderCard ReaderCard Reader

Cathode Lock Anode LockDoor Contact1 Door Contact2 Exit Button3 Exit Button4

2.2 K NO

COM

External Anti-Theft Detector

Normally Open

Normally Closed

NC

COM

External Anti-Theft Detector

2.2 K

Alarm Relay

Alarm Relay

+12 V External Power Supply

+12 V External Power Supply

RS-485+ Yellow

RS-485- Blue

RS-485+ Yellow

RS-485- Blue

RS-485+ Yellow

RS-485- Blue

RS-485+ Yellow

RS-485- Blue

Card Reader Card Reader Card Reader Card Reader

+12V GND RS485+ RS485- Lock1+ Lock1- Door

Contact1 Exit

Button1GND Door

Contact2 Exit

Button2 Lock2+Lock2- Lock3+Lock3- Door

Contact3 GND Door

Contact4 Exit

Button4Lock4+ Lock4- Exit

Button3

FIRE

Emergency Break Glass

PRESS HEREPRESS HERE

Fire Alarm Interface Note: After wiring RS-485 card readers, you should set Bit 6 of the card reader DIP switch to OFF and set Bit 1 to 4 as the DIP address. DIP address of Door 1 (Entrance) is 1 (decimal value), Door 1 (Exit) is 2, Door 2 (Entrance) is 3, Door 2 (Exit) is 4, Door 3 (Entrance) is 5, Door 3 (Exit) is 6, Door 4 (Entrance) is 7, and Door 4 (Exit) is 8.

Notes:

JP11

Br ow

n

O ra

ng e

Pu rp

le

W hi

te

G re

en

Bl ac

k

Br ow

n

O ra

ng e

Pu rp

le

W hi

te

G re

en

Bl ac

k

Br ow

n

O ra

ng e

Pu rp

le

W hi

te

G re

en

Bl ac

k

1 Wiring of Four-Door Access Controller After wiringthe Wiegand card readers, set Bit 6 of the card reader DIP switch to ON and set Bit 7 to select a Wiegand protocol. If setting Bit 7 as ON, it refers to Wiegand 26 protocol. If setting Bit 7 as OFF, it refers to Wiegand 34 protocol. For four-door access controller, Wiegand reader 1, 2, 3, and 4 represent Door 1, 2, 3, and 4 respectively. For two-door access controller, Wiegand reader 1, 2, 3, and 4 represent Door 1 (Entrance), Door 1 (Exit), Door 2 (Entrance) and Door 2 (Exit) respectively. For single door access controller, Wiegand reader 1 and 2 represent Door 1 (Entrance) and Door 2 (Exit) respectively.

Scan the QR code to get the user manual for detailed information. Note that mobile data charges may apply if Wi-Fi is unavailable.

N O

LED-A

LED1 LED2

LED-B LED-C LED-D

N C

NO NC

RS-485 Communication Indicator

Alarm Output Indicator

Battery Charging Indicator

Running Indicator DIP Switch

Charging Completed Indicator

Power Indicator

Network Data Indicator

Network Status Indicator

Alarm Input

N etw

ork Interface

Ev en

t In

pu t

NORMAL INITIAL

Z4 D 1+

D 1-

D 2+

D 2-

S1 B1 G N

D B2

+12 V GND BAT+ BAT-

RS-485A+ RS-485A-

GND

RS-485B+ RS-485B-

GND

RS-485C+ RS-485C-

GND

RS-485D+ RS-485D-

GND

NO/NC1 COM1

NO/NC2 COM2

NO/NC3 COM3

NO/NC4 COM4

G N

D +

12 V

G N

D +

12 V

G N

D W

0 W

1 BZ ER

R O

K

G N

D W

0 W

1 BZ ER

R O

K

G N

D W

0 W

1 BZ ER

R O

K

G N

D W

0 W

1 BZ ER

R O

K

C4 GND C3 C2 GND C1

G N

D S2G

N D

Z3Z2G N

D Z1

Lock Power

Reader Power Wiegand Reader 4 Wiegand Reader 3 Wiegand Reader 2 Wiegand Reader 1

Pow er

Supply Battery

R S-485 Reader

U plink R

S-485 A

larm O

utput

Lock1 Lock2

Door Contact Input

Exit Button

Choice 1 Step 1: Remove the jumper cap from the Normal terminal. Step 2: Disconnect the power and restart the access controller. The controller buzzer buzzes a long beep. Step 3: When the beep stopped, plug the jumper cap back to Normal. Step 4: Disconnect the power and restart the access controller.

Choice 2 Step 1: Jump the jumper cap from Normal to Initial. Step 2: Disconnect the power and reboot the access controller. The controller buzzer buzzes a long beep. Step 3: When the beep stopped, jump the jumper cap back to Normal. Step 4: Disconnect the power and reboot the access controller.

NO NC

INITIAL =

NORMAL =

Set the realy NO/NC status when setting the lock output and alarm output. The position of the jumper cap position and the related NO/NC status are as follows:

Set Bit 6 of the card reader DIP switch to OFF and set Bit 1 to 4 as the DIP address. Note: DIP address of Door 1 (Entrance) is 1 (decimal value), Door 1 (Exit) is 2, Door 2 (Entrance) is 3, Door 2 (Exit) is 4, Door 3 (Entrance) is 5, Door 3 (Exit) is 6, Door 4 (Entrance) is 7, and Door 4 (Exit) is 8.

ON

1 2 3 4 5 6 7 8

ON

1 2 3 4 5 6 7 8

DIP Switch Description Take the 8-bit DIP switch as an example; No.1 to No 8 is from the low bit to the high bit.

When the switch is towards ON, it means the switch is enabled, otherwise, the switch is off. If you set the DIP switch like the figure displayed below, its binary value is 00001100, and its decimal value is 12.

You are required to activate the control panel first before you can use the control panel. Activation via SADP, and activation via client software are supported. The default values of the terminal are as follows: The default IP address: 192.0.0.64 The default port No.: 8000 The default user name: admin

Activate Device via SADP Tool 1. Get the SADP tool from the supplied disk. Install and run the SADP tool. 2. Check the device status from the device list, and select an inactive device. 3. Create a password in the password field, and confirm the password. 4. Click Activate to activate the device. 5. Check the activated device. You can change the device IP address to the same IP segment with your computer by either modifying the IP address manually or checking the checkbox of Enable DHCP. 6. Input the password and click Modify to complete the configuration.

Activate Device via Client Software

NORMAL INITIAL

JP11

Normally Open Status

Relay 1 Relay 2 Relay 3 Relay 4

NO NC

Relay 1 Relay 2 Relay 3 Relay 4

Normally Closed Status

DIP Switch Settings of RS-485 Card Reader

DIP Switch Settings of Wiegand Card Reader

Set Bit 6 of the card reader DIP switch to ON and set Bit 7 to select a Wiegand protocol. Note: If setting Bit 7 as ON, it refers to Wiegand 26 protocol. If setting Bit 7 as OFF, it refers to Wiegand 34 protocol.

ON

1 2 3 4 5 6 7 8

ON

1 2 3 4 5 6 7 8

DIP Switch of Door 1 (Entrance)

DIP Switch of Wiegand 26 Protocol

N O

LED-A

LED1

LED2

LED-B LED-C LED-D

N C

RS-485 Communication Indicator

Alarm Output Indicator

Battery Charging Indicator

Running Indicator DIP Switch

Charging Completed Indicator

Power Indicator

Network Data Indicator

Network Status Indicator

Alarm Input

N etw

ork Interface

Door Contact Input

Exit ButtonLock1

NORMAL INITIAL

Z4 D 1+

D 1-

S1 B1 G N

D

+12 V GND BAT+ BAT-

RS-485A+ RS-485A-

GND RS-485B+ RS-485B-

GND

RS-485C+ RS-485C-

GND

RS-485D+ RS-485D-

GND

NO/NC1 COM1

NO/NC2 COM2

G N

D +

12 V

G N

D +

12 V

G N

D W

0 W

1 BZ ER

R O

K

G N

D W

0 W

1 BZ ER

R O

K

C2 GND C1

G N

D

G N

D Z3Z2G

N D

Z1

Lock Power

Reader Power Wiegand Reader2 Wiegand Reader 1

Pow er

Supply Battery

R S-485 Reader

U plink R

S-485 A

larm O

utput Ev en

t In

pu t

NO NC JP11

JP11

Note: The initializing of the hardware will restore all the parameters to the default setting and all the device events are wiping out.

STRONG PASSWORD RECOMMENDED We highly recommend you create a strong password of your own choosing (using a minimum of 8 characters, including upper case letters, lower case letters, numbers, and special characters) in order to increase the security of your product. And we recommend you reset your password regularly, especially in the high security system, resetting the password monthly or weekly can better protect your product.

Regulatory Information FCC Information Please take attention that changes or modification not expressly approved by the party responsible for compliance could void the users authority to operate the equipment. FCC compliance: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: Reorient or relocate the receiving antenna. Increase the separation between the equipment and receiver. Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. Consult the dealer or an experienced radio/TV technician for help. FCC Conditions This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: 1. This device may not cause harmful interference. 2. This device must accept any interference received, including interference that may cause undesired operation.

EU Conformity Statement This product and - if applicable - the supplied accessories too are marked with "CE" and comply therefore with the applicable harmonized European standards listed under the R&TTE Directive 1999/5/EC, the EMC Directive 2014/30/EU, the LVD Directive 2014/35/EU, the RoHS Directive 2011/65/EU. 2012/19/EU (WEEE directive): Products marked with this symbol cannot be disposed of as unsorted municipal waste in the European Union. For proper recycling, return this product to your local supplier upon the purchase of equivalent new equipment, or dispose of it at designated collection points. For more information see: www.recycle- this.info.

2006/66/EC (battery directive): This product contains a battery that cannot be disposed of as unsorted municipal waste in the European Union. See the product documentation for specific battery information. The battery is marked with this symbol, which may include lettering to indicate cadmium (Cd), lead (Pb), or mercury (Hg). For proper recycling, return the battery to your supplier or to a designated collection point. For more information see: www.recyclethis.info.

Industry Canada ICES-003 Compliance This device meets the CAN ICES-3 (B)/NMB-3(B) standards requirements.

2 Wiring of Single Door Access Controller

3 Wiring of Two-Door Access Controller

4 Hardware Initialization 5 Relay NO/NC Settings

6 DIP Switch Settings of Card Reader

7 Activation

1. Get the client software from the official website. Install and run the client software. 2. Enter the Device Management page. 3. Click Device on the top of the right panel. 4. Click Online Device to show the online device area at the bottom of the page. 5. Check the device status (shown on Security Level column) and select an inactive device. 6. Click Activate. 7. Create a password in t

Manualsnet FAQs

If you want to find out how the DS-K2601-G Hikvision works, you can view and download the Hikvision DS-K2601-G Controller Quick Start Guide on the Manualsnet website.

Yes, we have the Quick Start Guide for Hikvision DS-K2601-G as well as other Hikvision manuals. All you need to do is to use our search bar and find the user manual that you are looking for.

The Quick Start Guide should include all the details that are needed to use a Hikvision DS-K2601-G. Full manuals and user guide PDFs can be downloaded from Manualsnet.com.

The best way to navigate the Hikvision DS-K2601-G Controller Quick Start Guide is by checking the Table of Contents at the top of the page where available. This allows you to navigate a manual by jumping to the section you are looking for.

This Hikvision DS-K2601-G Controller Quick Start Guide consists of sections like Table of Contents, to name a few. For easier navigation, use the Table of Contents in the upper left corner.

You can download Hikvision DS-K2601-G Controller Quick Start Guide free of charge simply by clicking the “download” button in the upper right corner of any manuals page. This feature allows you to download any manual in a couple of seconds and is generally in PDF format. You can also save a manual for later by adding it to your saved documents in the user profile.

To be able to print Hikvision DS-K2601-G Controller Quick Start Guide, simply download the document to your computer. Once downloaded, open the PDF file and print the Hikvision DS-K2601-G Controller Quick Start Guide as you would any other document. This can usually be achieved by clicking on “File” and then “Print” from the menu bar.