Hikvision AE-VC143T-ITS Camera User's Manual PDF

1 of 9
1 of 9

Summary of Content for Hikvision AE-VC143T-ITS Camera User's Manual PDF

Vehicle-Mounted Camera

User Manual

UD13133B

i

UserManual

2018 Hangzhou Hikvision Digital Technology Co., Ltd.

About thisManual

This manual applies to Vehicle-Mounted Camera. This Manual is subject to domestic and international copyright protection. Hangzhou Hikvision Digital Technology Co., Ltd. (Hikvision) reserves all rights to this manual. This manual cannot be reproduced, changed, translated, or distributed, partially or wholly, by any means, without the prior written permission of Hikvision.

Trademarks

and other Hikvision marks are the property of Hikvision and are registered trademarks or the subject of applications for the same by Hikvision and/or its affiliates. Other trademarks mentioned in this manual are the properties of their respective owners. No right of license is given to use such trademarks without express permission.

Disclaimer

TO THE MAXIMUM EXTENT PERMITTED BY APPLICABLE LAW, HIKVISION MAKES NO WARRANTIES, EXPRESS OR IMPLIED, INCLUDING WITHOUT LIMITATION THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE, REGARDING THIS MANUAL. HIKVISION DOES NOTWARRANT, GUARANTEE, OR MAKE ANY REPRESENTATIONS REGARDING THE USE OF THE MANUAL, OR THE CORRECTNESS, ACCURACY, OR RELIABILITY OF INFORMATION CONTAINED HEREIN. YOUR USE OF THIS MANUAL AND ANY RELIANCE ON THIS MANUAL SHALL BE WHOLLY AT YOUR OWN RISK AND RESPONSIBILITY.

TO THE MAXIMUM EXTENT PERMITTED BY APPLICABLE LAW, IN NO EVENT WILL HIKVISION, ITS DIRECTORS, OFFICERS, EMPLOYEES, OR AGENTS BE LIABLE TO YOU FOR ANY SPECIAL, CONSEQUENTIAL, INCIDENTAL, OR INDIRECT DAMAGES, INCLUDING, AMONG OTHERS, DAMAGES FOR LOSS OF BUSINESS PROFITS, BUSINESS INTERRUPTION, SECURITY BREACHES, OR LOSS OF DATA OR DOCUMENTATION, IN CONNECTIONWITH THE USE OF OR RELIANCE ON THIS MANUAL, EVEN IF HIKVISION HAS BEEN ADVISED OF THE POSSIBILITY OF SUCH DAMAGES.

SOME JURISDICTIONS DO NOT ALLOW THE EXCLUSION OR LIMITATION OF LIABILITY OR CERTAIN DAMAGES, SO SOME OR ALL OF THE ABOVE EXCLUSIONS OR LIMITATIONS MAY NOT APPLY TO YOU.

ii

Regulatory Information FCC Information FCC compliance: This equipment has been tested and found to comply with the limits for a digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instruction manual, may cause harmful interference to radio communications. Operation of this equipment in a residential area is likely to cause harmful interference in which case the user will be required to correct the interference at his own expense. FCC Conditions This device complies with part 15 of the FCCRules. Operation is subject to the following two conditions: 1. This device may not cause harmful interference. 2. This device must accept any interference received, including interference that may cause undesired operation EU Conformity Statement

This product and - if applicable - the supplied accessories too are marked with "CE" and comply therefore with the

applicable harmonized European standards listed under the Low Voltage Directive 2014/35/EC, the EMC Directive 2014/30/EC.

2012/19/EU (WEEE directive): Products marked with this symbol cannot be disposed of as unsorted municipal waste in the European Union. For proper recycling, return this product to your local supplier

upon the purchase of equivalent new equipment, or dispose of it at designated collection points. For more information see: www.recyclethis.info.

2006/66/EC (battery directive): This product contains a battery that cannot be disposed of as unsorted municipal waste in the European Union. See the product

documentation for specific battery information. The battery is marked with this symbol, which may include lettering to indicate cadmium (Cd), lead (Pb), or mercury (Hg). For proper recycling, return the battery to your supplier or to a designated collection point. For more information see: www.recyclethis.info.

Industry Canada ICES-003 Compliance This device meets the CAN ICES-3 (A)/NMB-3(A) standards requirements.

iii

Safety Instruction These instructions are intended to ensure that user can use the product correctly to avoid danger or property loss. The precaution measure is divided into Warnings and Cautions Warnings: Serious injury or death may occur if any of the warnings are neglected. Cautions: Injury or equipment damage may occur if any of the cautions are neglected.

In the use of the product, you must be in strict compliance with the electrical safety regulations of the nation and region.

Refer to technical specifications for detailed information.

Input voltage should meet both the SELV (Safety Extra Low Voltage) and the Limited Power Source with AC 24V or DC 12V according to the IEC60950-1 standard. Refer to technical specifications for detailed information.

Do not connect several devices to one power adapter as adapter overload may cause over-heating or a fire hazard.

Make sure that the plug is firmly connected to the power socket.

When the product is mounted on wall or ceiling, the device shall be firmly fixed.

If smoke, odor or noise rise from the device, turn off the power at once and unplug the power cable, and then please contact the service center.

If the product does not work properly, contact your dealer or the nearest service center. Never attempt to disassemble the camera by yourself. (We shall not assume any responsibility for problems caused by unauthorized repair or maintenance.)

Make sure the power supply voltage is correct before using the camera.

Do not drop the camera or subject it to physical shock. Do not touch senor modules with fingers. If cleaning is

necessary, use clean cloth with a bit of ethanol and wipe it gently. If the camera will not be used for an extended period, replace the lens cap to protect the sensor from dirt.

Do not aim the camera at the sun or extra bright places. Blooming or smearing may occur otherwise

iv

(which is not a malfunction), and affect the endurance of sensor at the same time.

The sensor may be burned out by a laser beam, so when any laser equipment is in using, make sure that the surface of sensor will not be exposed to the laser beam.

Do not place the camera in extremely hot, cold, dusty or damp locations, and do not expose it to high electromagnetic radiation.

To avoid heat accumulation, good ventilation is required for operating environment.

Keep the camera away from liquid while in use. While in delivery, the camera shall be packed in its

original packing, or packing of the same texture. Symbol Conventions The symbols that may be found in this document are defined as follows.

Symbol Description Provides additional information to emphasize or supplement important points of the main text.

Indicates a potentially hazardous situation, which if not avoided, could result in equipment damage, data loss, performance degradation, or unexpected results.

Indicates a hazard with a high level of risk, which if not avoided, will result in death or serious injury.

1

1 Introduction

1.1 Product Features This series of camera adopts new generation sensor with high sensitivity and advanced circuit design technology. It features high resolution, low image distortion and low noise, etc., which makes it suitable for monitoring system and image processing system. The main features are as follows: High performance CMOS sensor High resolution image Low illumination, 0.1 lux @ (F1.2, AGC ON) Supports auto electronic day & night switch Supports auto white balance Adapts shock-proof design and 4-pin din connector

1.2 Overview

1.2.1 Overview of Vehicle-Mounted Camera The overview of the camera is shown below.

3M Gum Mounting Base

4-Pin Din Connector Camera Body

Overview

1.2.2 4-Pin Din Connetor Interface The connector interface is shown in below.

Power GroundingVideo

Audio

4-Pin Din Connector

Interfaces of 4-Pin Din Connector

2

2 Installation

2.1 Installation You can paste the camera with3M gum or fix it with screws. Choose the installation method according to the mounting place. Before you start: Please make sure that the device in the package is in

good condition and all the assembly parts are included.

Make sure that all the related equipment is power-off during the installation.

Check the specification of the products for the installation environment.

Check whether the power supply is matched with your power output to avoid damage.

Be sure that there is enough space to install the camera and accessories.

Make sure the part, which is used to install the camera, is strong enough to withstand four times the weight of the camera and the mounting.

If the product does not function properly, please contact your dealer or the nearest service center. Do not disassemble the camera for repair or maintenance by yourself.

Do not pull and drag the camera cables hard.

3M GumMounting Steps: 1. Clean the mounting surface with a mixture of isopropyl and water.

Clean Mounting Surface 2. Paste the electrostatic film (in the package) onto the mounting surface.

Electrostatic Film

3

Paste the Electrostatic Film 3. Peal the paster of the 3M gum.

Paster

Peal the Paster 4. Paste the camera onto the electrostatic film. 5. Let the camera stand for 12 h to make sure its secured.

Screw Mounting Steps: 1. Drill according to the hole position on the paster. 2. Align the camera to the screw holes and fix it with two screws (in the package).

ScrewHole

Screw

Mounting Surface

Fix the Camera

2.2 Adjust Angle Steps: 1. Connect the camera to specific device for preview.

Specifi c

Device 4-Pin Din Connector Camera

Connect to Specific Device

Obtain detailed information for specific device from the dealer. 2. Thread the cable through the anti-rotating lock. Turn the camera to the target angle. 3. Clip the anti-rotating lock into the mounting base.

<

Manualsnet FAQs

If you want to find out how the AE-VC143T-ITS Hikvision works, you can view and download the Hikvision AE-VC143T-ITS Camera User's Manual on the Manualsnet website.

Yes, we have the User's Manual for Hikvision AE-VC143T-ITS as well as other Hikvision manuals. All you need to do is to use our search bar and find the user manual that you are looking for.

The User's Manual should include all the details that are needed to use a Hikvision AE-VC143T-ITS. Full manuals and user guide PDFs can be downloaded from Manualsnet.com.

The best way to navigate the Hikvision AE-VC143T-ITS Camera User's Manual is by checking the Table of Contents at the top of the page where available. This allows you to navigate a manual by jumping to the section you are looking for.

This Hikvision AE-VC143T-ITS Camera User's Manual consists of sections like Table of Contents, to name a few. For easier navigation, use the Table of Contents in the upper left corner.

You can download Hikvision AE-VC143T-ITS Camera User's Manual free of charge simply by clicking the “download” button in the upper right corner of any manuals page. This feature allows you to download any manual in a couple of seconds and is generally in PDF format. You can also save a manual for later by adding it to your saved documents in the user profile.

To be able to print Hikvision AE-VC143T-ITS Camera User's Manual, simply download the document to your computer. Once downloaded, open the PDF file and print the Hikvision AE-VC143T-ITS Camera User's Manual as you would any other document. This can usually be achieved by clicking on “File” and then “Print” from the menu bar.