Hikvision AE-VC124T-IT Camera User's Manual PDF

Vehicle-Mounted Camera

User Manual

UD09114B-A

1

UserManual 2018 HangzhouHikvision Digital Technology Co., Ltd.

AboutthisManual This manual applies to Vehicle-Mounted Camera. This Manual is subject to domestic and international copyright protection. Hangzhou Hikvision Digital Technology Co., Ltd. (Hikvision) reserves all rights to this manual. This manual cannot be reproduced, changed, translated, or distributed, partially or wholly, by any means, without the prior written permission of Hikvision.

Trademarks

and other Hikvision marks are the property of Hikvision and are registered trademarks or the subject of applications for the same by Hikvision and/or its affiliates. Other trademarks mentioned in this manual are the properties of their respective owners. No right of license is given to use such trademarks without express permission.

Disclaimer TO THEMAXIMUM EXTENT PERMITTED BY APPLICABLE LAW, HIKVISIONMAKES NO WARRANTIES, EXPRESS OR IMPLIED, INCLUDING WITHOUT LIMITATION THE IMPLIED WARRANTIES OFMERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE, REGARDING THIS MANUAL. HIKVISION DOES NOT WARRANT, GUARANTEE, OR MAKE ANY REPRESENTATIONS REGARDING THE USE OF THE MANUAL, OR THE CORRECTNESS, ACCURACY, OR RELIABILITY OF INFORMATION CONTAINEDHEREIN. YOUR USE OF THISMANUAL AND ANY RELIANCE ON THIS MANUAL SHALL BE WHOLLY AT YOUR OWN RISK AND RESPONSIBILITY.

TO THE MAXIMUM EXTENT PERMITTED BY APPLICABLE LAW, IN NO EVENT WILL HIKVISION, ITS DIRECTORS, OFFICERS, EMPLOYEES, OR AGENTS BE LIABLE TO YOU FOR ANY SPECIAL, CONSEQUENTIAL, INCIDENTAL, OR INDIRECT DAMAGES, INCLUDING, AMONG OTHERS, DAMAGES FOR LOSS OF BUSINESS PROFITS, BUSINESS INTERRUPTION, SECURITY BREACHES, OR LOSS OF DATA OR DOCUMENTATION, IN CONNECTION WITH THEUSE OF OR RELIANCE ON THIS MANUAL, EVEN IF HIKVISION HAS BEEN ADVISED OF THE POSSIBILITY OF SUCH DAMAGES.

SOME JURISDICTIONS DO NOT ALLOW THE EXCLUSION OR LIMITATION OF LIABILITY OR CERTAIN DAMAGES, SO SOME OR ALLOF THE ABOVE EXCLUSIONS OR LIMITATIONS MAY NOT APPLY TO YOU.

2

RegulatoryInformation FCCInformation FCCcompliance:Thisequipment has been tested and found to comply with the limits for a digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instruction manual, may cause harmful interference to radio communications. Operation of this equipment in a residential area is likely to cause harmful interference in which case the user will be required to correct the interference at his own expense. FCCConditions This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: 1. This devicemay not cause harmful interference. 2. This devicemust accept any interference received, including interference that may cause undesired operation EUConformityStatement

This product and - if applicable - the supplied accessories too are marked with "CE" and comply therefore with the

applicable harmonized European standards listed under the Low Voltage Directive 2014/35/EC, the EMC Directive 2014/30/EC.

2012/19/EU (WEEE directive): Products marked with this symbol cannot be disposed of as unsorted municipal waste in the European Union. For proper recycling, return this product to your local supplier

upon the purchase of equivalent new equipment, or dispose of it at designated collection points. For more information see: www.recyclethis.info.

2006/66/EC (battery directive): This product contains a battery that cannot be disposed of as unsorted municipal waste in the European Union. See the product

documentation for specific battery information. The battery is markedwith this symbol, which may include lettering to indicate cadmium (Cd), lead (Pb), or mercury (Hg). For proper recycling, return the battery to your supplier or to a designated collection point. For more information see: www.recyclethis.info.

Industry CanadaICES-003Compliance This device meets the CAN ICES-3 (A)/NMB-3(A) standards requirements.

3

Safety Instruction These instructions are intended to ensure that user can use the product correctly to avoid danger or property loss. The precautionmeasure is divided into Warnings and Cautions Warnings:Seriousinjury or death may occur if any of the warnings are neglected. Cautions:Injuryor equipment damage may occur if any of the cautions are neglected.

In the use of the product, you must be in strict compliance with the electrical safety regulations of the nation and region.

Refer to technical specifications for detailed information.

Input voltage should meet both the SELV (Safety Extra Low Voltage) and the Limited Power Source with AC 24V or DC 12V according to the IEC60950-1 standard. Refer to technical specifications for detailed information.

Do not connect several devices to one power adapter as adapter overload may cause over-heating or a fire hazard.

Make sure that the plug is firmly connected to the power socket.

When the product ismounted on wall or ceiling, the device shall be firmly fixed.

If smoke, odor or noise rise from the device, turn off the power at once and unplug the power cable, and then please contact the service center.

If the product does not work properly, contact your dealer or the nearest service center. Never attempt to disassemble the camera by yourself. (We shall not assume any responsibility for problems caused by unauthorized repair or maintenance.)

Make sure the power supply voltage is correct before using the camera.

Do not drop the camera or subject it to physical shock. Do not touch senor moduleswith fingers. If cleaning is

necessary, use clean clothwith a bit of ethanol and wipe it gently. If the camera will not be used for an extended period, replace the lens cap to protect the sensor from dirt.

Do not aim the camera at the sun or extra bright places. Blooming or smearingmay occur otherwise (which is not a malfunction), and affect the endurance of sensor at the same time.

4

The sensor may be burned out by a laser beam, so when any laser equipment is in using, make sure that the surface of sensor will not be exposed to the laser beam.

Do not place the camera in extremely hot, cold, dusty or damp locations, and do not expose it to high electromagnetic radiation.

To avoid heat accumulation, good ventilation is required for operating environment.

Keep the camera away from liquidwhile in use. While in delivery, the camera shall be packed in its

original packing, or packing of the same texture. SymbolConventions The symbols that may be found in this document are defined as follows.

Symbol Description Provides additional information to emphasize or supplement important points of the main text.

Indicates a potentially hazardous situation, which if not avoided, could result in equipment damage, data loss, performance degradation, or unexpected results. Indicates a hazard with a high level of risk, which if not avoided, will result in death or serious injury.

5

Introduction

1.1 Product Features This series of camera adopts new generation sensor with high sensitivity and advanced circuit design technology. It features high resolution, low image distortion and low noise, etc., which makes it suitable for surveillance system and image processing system. The main features are as follows: High performance CMOS sensor and high resolution

bring high-quality image. AGC (Auto Gain Control). Aviation plug output, shock proof. IP68.

1.2 Overview

1.2.1 Overview of Vehicle-Mounted Camera The overview of the camera is shown below.

4-Pin Aviation Plug

Lens

Bracket

Cover

Overview

1.2.2 Aviation Plug Interfaces There are 2 types for the aviation plug interfaces, as shown in below.

Video Interface

GND Power Supply

GND Video Interface

GND

Power Supply

GND

Type A Type B

Interfaces of Aviation Plug

Installation Beforeyoustart:

6

Please make sure that the device in the package is in good condition and all the assembly parts are included.

Make sure that all the related equipment is power-off during the installation.

Check the specification of the products for the installation environment.

Check whether the power supply is matchedwith your power output to avoid damage.

Be sure that there is enough space to install the camera and accessories.

Make sure the part, which is used to install the camera, is strong enough towithstand four times the weight of the camera and the mounting.

If the product does not function properly, please contact your dealer or the nearest service center. Do not disassemble the camera for repair or maintenance by yourself.

Do not pull and drag the camera cables hard. Steps:

Paste the drill template to the vehicle wall. Drill the screw holes according to the drill

template.

Drill Template Loosen 4 crews (M2.5 x 7) on the cover.

Set Screws M 2.5 7

Loosen Screws Align the holes on the bracket with the installation

holes on the drill template. Use 3 crews (PA4 x 25) to secure the bracket to the

template. Holes for Fixing

Bracket

Secure Bracket

7

Route cameras cables through the cable hole of the bracket.

Seal Ring

Fixing Hole

Route the Cable Secure the seal ring near the cable hole. Adjust the camera main body with UP upward as

the figure below.

Adjust Camera (Optional) If the installation site of the camera

needs to be sealed, please wipe silica gel on the screw position and the cable hole, and seal them.

Align the cover with the crew holes on the bracket, and insert 4 set crews (M2.5 x 7).

4 M2.5 x 7 Srews

Insert Screws Connect