GE UVD6361S UVD6361DPBB Vent System Installation Instructions PDF

1 of 40
1 of 40

Summary of Content for GE UVD6361S UVD6361DPBB Vent System Installation Instructions PDF

Write the model and serial numbers here:

Model # _________________

Serial # _________________

These numbers are also found on the Product Property Registration Card sent separately with your downdraft ventilation system and on the label located on the front panel of the unit.

ESPAOL Para consultar una version en

espaol de este manual de instrucciones, visite nuestro sitio de

internet GEAppliances.com.

V EN

T SY

ST EM

D o

w nd

ra ft

49-2000733 Rev. 1 09-20 GEA

SAFETY INFORMATION . . . . . . . . . . . 3

USING THE HOOD Downdraft Vent System . . . . . . . . . . . . . . . . . . 5

CARE AND CLEANING Downdraft Vent System . . . . . . . . . . . . . . . . . . 6

INSTALLATION INSTRUCTIONS . . 7

TROUBLESHOOTING TIPS . . . . . . . . 16

LIMITED WARRANTY . . . . . . . . . . . . . 17

ACCESSORIES . . . . . . . . . . . . . . . . . . . . . 18

CONSUMER SUPPORT . . . . . . . . . . . . 20

UVD6301S UVD6361S

OWNERS MANUAL & INSTALLATION INSTRUCTIONS

GE is a trademark of the General Electric Company. Manufactured under trademark license.

2 49-2000733 Rev. 1

THANK YOU FOR MAKING GE APPLIANCES A PART OF YOUR HOME.

Whether you grew up with GE Appliances, or this is your first, were happy to have you in the family.

We take pride in the craftsmanship, innovation and design that goes into every GE Appliances product, and we think you will too. Among other things, registration of your appliance ensures that we

can deliver important product information and warranty details when you need them.

Register your GE appliance now online. Helpful websites and phone numbers are available in the Consumer Support section of this Owners Manual. You may also mail in the pre-printed registration

card included in the packing material.

49-2000733 Rev. 1 3

SA FETY IN

FO R

M A

TIO N

IMPORTANT SAFETY INFORMATION READ ALL INSTRUCTIONS BEFORE USING

READ AND SAVE THESE INSTRUCTIONS

WARNING TO REDUCE THE RISK OF FIRE, ELECTRIC SHOCK OR INJURY TO PERSONS, OBSERVE THE FOLLOWING: A. Use this unit only in the manner intended by the

manufacturer. If you have questions, contact the manufacturer.

B. Before servicing or cleaning unit, switch power off at service panel and lock the service disconnecting means to prevent power from being switched on accidentally. When the service disconnecting means cannot be locked, securely fasten a prominent warning device, such as a tag, to the service panel.

C. Do not use this unit with any solid-state speed control device.

D. Plug your vent system into a 120-volt grounded outlet only. Do not remove the round grounding prong from the plug. If in doubt about the grounding of the home electrical system, it is your responsibility and obligation to have an ungrounded outlet replaced with a properly grounded, three prong outlet in accordance with the National Electrical Code. Do not use an extension cord with this appliance.

CAUTION FOR GENERAL VENTILATING USE ONLY. DO NOT USE TO EXHAUST HAZARDOUS OR EXPLOSIVE MATERIALS AND VAPORS.

WARNING TO REDUCE THE RISK OF INJURY TO PERSONS IN THE EVENT OF A RANGE TOP GREASE FIRE, OBSERVE THE FOLLOWING*: A. SMOTHER FLAMES with a close-fitting lid, cookie

sheet or metal tray, then turn off the burner. BE CAREFUL TO PREVENT BURNS. If the flames do not go out immediately, EVACUATE AND CALL THE FIRE DEPARTMENT.

B. NEVER PICK UP A FLAMING PANYou may be burned.

C. DO NOT USE WATER, including wet dishcloths or towelsa violent steam explosion will result.

D. Use an extinguisher ONLY if: 1. You know you have a Class ABC extinguisher,

and you already know how to operate it. 2. The fire is small and contained in the area where

it started. 3. The fire department is being called. 4. You can fight the fire with your back to an exit.

* Based on Kitchen Fire Safety published by NFPA.

WARNING TO REDUCE THE RISK OF A RANGE TOP GREASE FIRE: A. Never leave surface units unattended at high

settings. Boilovers cause smoking and greasy spillovers that may ignite. Heat oils slowly on medium settings.

B. Always turn hood ON when cooking at high heat or when flambing food (i.e. Crepes Suzette, Cherries Jubilee, Peppercorn Beef Flamb).

C. Clean ventilating fans frequently. Grease should not be allowed to accumulate on fan or filter.

D. Use proper pan size. Always use cookware appropriate for the size of the surface element.

If You Need Service Do not attempt to repair or replace any part of the vent system unless it is specifically recommended in this manual. All other servicing should be referred to a qualified technician. Be sure electrical power is off before servicing the unit. It may be necessary to remove the vent system blower system in order to service components such as the blower motor or air vent mechanism. Disconnect power to the cooktop and remove it first. Reverse the steps in the Install Downdraft Vent section in the Installation Instructions to remove the blower. Service parts are available from a GE Appliances Service and Parts Center. Make sure all fingers are away from the top of the vent system when it is lowered.

4 49-2000733 Rev. 1

SA FE

TY IN

FO R

M A

TI O

N IMPORTANT SAFETY INFORMATION READ ALL INSTRUCTIONS BEFORE USING

READ AND SAVE THESE INSTRUCTIONS

How to Remove Protective Shipping Film and Packaging Tape Carefully grasp a corner of the protective shipping film with your fingers and slowly peel it from the appliance surface. Do not use any sharp items to remove the film. Remove all of the film before using the appliance for the first time. To assure no damage is done to the finish of the product, the safest way to remove the adhesive from packaging tape on new appliances is an application of a household liquid dishwashing detergent. Apply with a soft cloth and allow to soak. NOTE: The adhesive must be removed from all parts. It cannot be removed if it is baked on.

ATTENTION: Please remove the bubble wrap inserted inside of exhaust before installation. Make sure nothing is left inside the blower box.

Bubble Wrap

49-2000733 Rev. 1 5

Downdraft Vent System U

SIN G

TH E VEN

T SYSTEM : D

ow ndraft Vent System

When Using The Vent System CAUTION Be careful when raising or lowering

the vent. Be sure pots, pot handles and other objects are clear of the vent and cannot be struck or tipped by the vent being raised. NOTE: There is a slight trim overhang on each side of the vent.

cover when it is being lowered.

IMPORTANT: If the vent is obstructed by an object while it is being raised or lowered, it will stop. Carefully remove the obstruction and the vent will drop to the lowered position. Press the button again to return to normal functons.

To Use The Downdraft System To raise the downdraft vent, press the button on the top cover. The vent will rise.

The blower can be turned ON or OFF and the speed can be adjusted with the recessed knob on the right side of the air vent. The blower, if left on, will automatically turn off when the vent is lowered. NOTE: For most convenient operation, set the blower to the speed you use most often. The blower will come on to this speed whenever the unit is raised. Lower the downdraft vent by pressing the button on the top cover. The vent will go down an the blower will shut off.

Cooking Tips The high air movement of this vent system can increase the cooking times for some foods. It may take longer to reach high cooking temperatures if the vent system is turned to high right away. Adjust the fan speed for best cooking results.

For best results when heating oil for deep frying or when boiling water, use the front surface units or wait until the water is boiling or the oil is at frying temperatures before turning on the vent system. The vent system may not completely capture all the steam from pans on the front burners.

Button

6 49-2000733 Rev. 1

C A

R E

A N

D C

LE A

N IN

G : D

ow nd

ra ft

Ve nt

S ys

te m Downdraft Vent System

Painted Or Stainless Steel Surfaces Do not use a steel wool pad; it will scratch the surface. To clean the stainless steel surface, use warm, sudsy water or a stainless steel cleaner or polish. Always wipe the surface in the direction of the grain. Follow the cleaner instructions for cleaning the stainless steel surface. For difficult stains on stainless steel, use a cleaner that contains lactic acid or citric acid.

To inquire about purchasing cleaning products including stainless steel appliance cleaner or polish read the Assistance and Accessories sections at the beginning of this manual.

Grease Filters The efficiency of your vent system depends on a clean filter. Frequency of cleaning depends on the type of cooking you do. Grease filters should be cleaned at least once a month. Never operate the vent system without the filters in place. To remove: Remove filters from the air vent by reaching the filters through the vent openings, pushing down then pulling out. NOTE: The filters are different sizes. Be sure to replace them as removed, wider one on the left To clean: Soak and then agitate in a hot detergent solution. Light brushing may be used to remove embedded soil. Rinse, shake and remove moisture before replacing. Do not clean the filters in the dishwasher. With careful handling, the filter will last for years. If replacement becomes necessary, order the part from your dealer.

Filter Tabs

49-2000733 Rev. 1 7

Installation Instructions

If you have questions, call GE Appliances at 800.GE.CARES (800.432.2737) or visit our website at: GEAppliances.com

IN STA

LLATIO N

IN STR

U C

TIO N

S

BEFORE YOU BEGIN Read these instructions completely and carefully.

IMPORTANT Save these instructions for local inspectors use.

IMPORTANT Observe all governing codes and ordinances.

Note to Installer Be sure to leave these instructions with the Consumer.

Note to Consumer Keep these instructions for future reference.

Skill level Installation of this vent hood requires basic mechanical and electrical skills.

Proper installation is the responsibility of the installer.

Product failure due to improper installation is not covered under the Warranty.

GROUNDING INSTRUCTIONS This appliance must be grounded. In the event of an electrical short circuit, grounding reduces the risk of electric shock by providing an escape wire for the electric current. This appliance is equipped with a cord having a grounding wire with a grounding plug. The plug must be plugged into an outlet that is property installed and grounded.

WARNING Improper grounding can result in a risk of electric shock. Consult a qualified electrician if the grounding instructions are not completely understood, or if doubt exist as to whether the appliance is properly grounded. Do not use an extension cord. If the power supply cord is too short, have a qualified electrician install an outlet near the appliance. If you received a damaged vent system, you should contact your dealer.

Downdraft Vent Systems UVD6301S, UVD6361S

PARTS SUPPLIED Open the carton and remove parts package. Check contents to be sure all pieces are present.

REMOVE PACKAGING Remove the shipping materials and the carton; set carton aside. The carton can be used as a pad when changing or adjusting vent direction.

TOOLS AND MATERIALS REQUIRED Safety glasses Large flat-blade screwdriver Jigsaw Carpenters square Ductwork to suit the installation Level

Stabilizing Brackets Qty:2

Filters - inside unit Qty:2

Countertop Mounting Screw, 1/4-20 x 2.00

Hex Hd Qty:2

Plastic Template (attached to product) Qty:1

Downdraft Leveling Screw, 1/4-20 x .50 Hex

Hd - Qty:2 Wood Screw, #8 x .750 SI Round Hd

- Qty:4

28.5 for 30 Models 34 for 36 Models

8 49-2000733 Rev. 1

Safety Information IN

ST A

LL AT

IO N

IN ST

R U

C TI

O N

S

WARNING TO REDUCE THE RISK OF FIRE, ELECTRIC SHOCK OR INJURY TO PERSONS, OBSERVE THE FOLLOWING:

done by qualified person(s) in accordance with all applicable codes and standards, including fire-rated construction.

exhausting of gases through the flue (chimney) of fuel burning equipment to prevent back drafting. Follow the heating equipment manufacturers guidelines and safety standards such as those published by the National Fire Protection Association (NFPA), the American Society for Heating, Refrigeration and Air Conditioning Engineers (ASHRAE) and the local code authorities.

damage electrical wiring and other hidden utilities.

CAUTION TO REDUCE THE RISK OF FIRE AND TO PROPERLY EXHAUST AIR, BE SURE TO DUCT AIR OUTDOORS. DO NOT VENT EXHAUST AIR INTO SPACES WITHIN WALLS OR CEILINGS OR INTO ATTICS, CRAWL SPACES OR GARAGES.

WARNING TO REDUCE THE RISK OF FIRE, USE ONLY METAL DUCT WORK.

air system in accordance with local building code requirements. Visit GEAppliances.com for available makeup air solutions.

slab if allowed by local code board.

49-2000733 Rev. 1 9

Installation Preparation IN

STA LLATIO

N IN

STR U

C TIO

N S

POWER SUPPLY This downdraft vent must be supplied with 120V, 60 Hz. and connected to an individual, properly grounded branch circuit, protected by a 15- or 20-ampere circuit breaker or time-delay fuse. A properly grounded 3-prong receptacle should be located within reach of the vents two-foot power cord. Gas Cooktops If this vent is installed in combination with a GE or

Monogram gas cooktop, it may operate from the same duplex outlet.

Electric Cooktops If this vent is installed in combination with a GE or

Monogram electric cooktop, the vent must operate from a separate 120V outlet.

Locate the receptacle inside the cabinet on the right side wall (see illustration). The receptacle cannot be placed on the back of the cabinet wall where it may interfere with the downdraft plenum. The downdraft vent power cord is to be routed beneath the cooktop and routed away from heat generated by the cooktop. Ensure that the cooktop is installed per manufacturers installation instructions.

IMPORTANT (Please read carefully) The power cord of this appliance is equipped with a three-prong (grounding) plug which mates with a standard three-prong grounding wall receptacle to minimize the possibility of electric shock. The customer should have the wall receptacle and circuit checked by a qualified electrician to make sure the receptacle is properly grounded and has correct polarity. Where a standard two-prong wall receptacle is

encountered, it is the personal responsibility and obligation of the customer to have it replaced with a properly grounded three-prong wall receptacle.

Do not, under any circumstances, cut or remove the third (ground) prong from the power cord. Do not use an extension cord or adapter plug with this appliance. Follow National Electrical Code or prevailing local codes and ordinances. Location of Rating Label: on front of chassis of vent system.

VOLTS AMPS DUCT 120 4.0 3-1/4 X 10

SPECIFICATIONS

DO NOT Locate Gas or Electrical Connections within this Area

34"(cutout width) for 36" models 28-1/2" (cutout width) for 30" models

29-1/2"

12"

Electrical Outlet 12"

Above Cabinet

Floor

Locate the gas or electrical connection only within the

shaded area.

10 49-2000733 Rev. 1

Installation Preparation IN

ST A

LL AT

IO N

IN ST

R U

C TI

O N

S

PRODUCT DIMENSIONS A B

30 Models 30 26-1/4 36 Models 36 32-1/4

A

B

22.3

2

2-1/2

7

7-1/4

36-1/2

49-2000733 Rev. 1 11

IN STA

LLATIO N

IN STR

U C

TIO N

S Installation Preparation

PREPARING FOR INSTALLATION Unpack the cooktop and read the Installation

Instructions to understand the required countertop cutout dimensions and location in the countertop, the cooktop spacing to the front edge of the countertop, and the required clearances to the cabinets and walls. The vent system required cutout width is shown on page 9. Confirm there is enough side to side counter space to meet the required spacing and clearances for the cooktop.

Using the illustrations below and taking measurements of the cooktop to establish dimension A, confirm there is enough front to back counter space (dimension B) to fit both the cooktop and the vent system. Note the cooktop rear edge will overlap the vent system front surface (refer to Page 10).

Refer to the Creative Solutions section on page 13 if more counter space is needed.

Using the illustrations on pages 9 through 12 and taking measurements of the vent system and its exhaust vent location, confirm the clearances needed within the cabinet, the exhaust vent direction, and the alignment of the exhaust vent with the ducting. If needed for clearance or duct hookup alignment, reposition the location of the cooktop, or modify the cabinetry, or modify the ducting.

Confirm the electrical receptacles and gas lines are correctly located, and relocate if needed.

B

C

B is the minimum dimension of the flat portion of countertop that is needed

A A is the dimension from the screw head on the front surface of

the cooktop base to the rear edge of the cooktop. If you cannot find dimension A in the cooktop installations instructions, then you must measure it.

Depth of cutout is A + 2 1/8 Minimum counter depth B = A + C + 2.5"

Dimension C is defined in cooktop Installation Instruction

COOKTOP

1/8 minimum

Front edge of countertop

Front of cutout in countertop

Screw head Front edge

of cooktop

Front of cutout in countertop

Back edge of cooktop

Back of cut in countertop

2 1/8

3/8 minimum

D o w n d r a f t

V e n t

Counter Top

Gear Motor Cover

Blower Box

Cook Top Chimney Top

Air Vent

120 Vac Grounded Outlet

3-1/4" x 10" Duct Connector

12 49-2000733 Rev. 1

Installation Preparation IN

ST A

LL AT

IO N

IN ST

R U

C TI

O N

S

VENTING OPTIONS The downdraft vent is shipped with the discharge

outlet pointing straight down and can be changed to the left or right side. To avoid interference problems, the downdraft vent cannot be vented to the right when installed with a GE or Monogram gas cooktop, or with a GE or Monogram non-induction electric cooktop.

The blower outlet is sized for 3-1/4 x 10 and can be transitioned to 6 round.

The blower is shipped with its discharge facing DOWN. Follow these steps ONLY if: the position of the blower discharge needs to be

moved so ductwork does not interfere with floor joists, plumbing or wiring below.

it is necessary to rotate the blower discharge to the RIGHT or LEFT.

Place the unit on its back on a table or work surface. Pull out the bubble wrap sheet. Make sure nothing is left inside. DOWN DISCHARGE - MOVING BLOWER LEFT OR RIGHT

1. Loosen the 4 nuts and 2 clamp channels. 2. Remove the 5 screws on the bottom. These 5

screws are for shipping and do not need to be re-tightened.

3. Slide blower to desired position. 4. Use supplied cover plate to close open space (if

any). 5. Tighten wing nuts to secure top of blower and use

sheet metal screws through bottom flange to secure bottom of blower.

LEFT OR RIGHT DISCHARGE

1. Remove the 4 nuts and 2 clamp channels. 2. Remove the 5 screws on the bottom. These 5

screws are for shipping and do not need to be re-tightened.

3. Carefully lift blower and disconnect motor plug if necessary. Reposition blower and RECONNECT MOTOR PLUG.

4. Use supplied cover plate to close open space (if any).

5. Replace clamp channels and use nuts to secure the blower in its new position.

6. Use sheet metal screws through bottom flange to secure bottom of blower.

For best performance: Choose the ducting option which allows the shortest length of ductwork and a minimum number of elbows and transitions. Check location of floor joists, wall studs, electrical wiring or plumbing for possible interference. NOTE: The unit is shipped with the 3-1/4" x 10" discharge facing DOWN. See CHANGING BLOWER DIRECTION on page 3, if necessary. The system will operate most efficiently when the ductwork does not exceed 40 feet of equivalent duct. The chart, below, shows equivalent feet of elbows and transitions. The number of feet of straight duct plus the equivalent feet of transitions and/or elbows to be used should equal 40 feet or less.

Nut Blower

Motor Plug

Sheet Metal Screw

Cover Plate

Clamp Channel

Nuts

Blower

Clamp Channel

Sheet Metal Screws

Bottom Flange

6" Round Elbow

3-1/4"x10" to 6" Round Transition

3-1/4"x10" 90 Elbow

equals 6 ft. of straight duct

equals 2 ft. of straight duct

equals 8 ft. of straight duct

Bubble Wrap Sheet

49-2000733 Rev. 1 13

IN STA

LLATIO N

IN STR

U C

TIO N

S Design Information

CREATIVE SOLUTIONS When the kitchen

design calls for an against-the-wall installation, move the base cabinet forward 3 to 5. Filler panels or complementary moldings can be added to exposed cabinet sides.

In an island or peninsula, use an extra-deep countertop. The countertop overhang at the front can be adjusted to meet setback to cutout requirements.

When the cutout to the front edge of the countertop requirement is more than 2, add a bullnose trim to the front edge of the countertop. Include the trim thickness when measuring the front edge to cutout requirement. By adding the trim, the cooktop can be moved forward,

providing additional countertop depth and interior cabinet space.

When the distances between the vent and the inside cabinet side walls are more than 5-1/2 and/ or the inside cabinet back wall is more than 4-1/2, false walls should be constructed inside the cabinet for securing the vent with the stabilizing brackets (refer to Cutouts and Clearances under Installation Preparation.)

PREPARING THE COUNTERTOP Lay out and cut the cooktop cut-out far enough FORWARD so downdraft will fit behind it. 1. Set cooktop in place and

slide it as far forward as possible. Center and square it with edges or countertop.

2. Place the plastic template against the back flange of the cooktop and center it. Trace around template to mark the downdraft opening.

3. Remove cooktop from countertop. 4. Cut downdraft opening. Be careful not to chip edges

of countertop.

Cover Panel

End Panel

Countertop Overhang per Cooktop Clearances Must be Maintained

Base Cabinet

Filler Panel Base Sink

Filler Panel

Maintain Cutout Clearances to Front Edge as Specified

14 49-2000733 Rev. 1

PREPARE FOR DUCTWORK Determine the best route for ductwork; it can be routed in a variety of ways depending on the kitchen layout. IMPORTANT: The downdraft air discharge outlet

accordingly. Typical duct arrangement countertop series.

To maximize the ventilation performance of the vent system: 1. Minimize the duct run length and number of

transitions and elbows. 2. Maintain a constant duct size. 3. Seal all joints with duct tape to prevent any leaks. 4. Do not use any type of flexible ducting.

Design Information IN

ST A

LL AT

IO N

IN ST

R U

C TI

O N

S

Inside wall cabinet

Up inside wall to roof or overhang

Directly to outside

Between floor joists Through cabinet toe space

Peninsula or island Peninsula

Outside wall cabinet

NOTE: PVC sewer pipe type PSM 12454-B Schedule 40 ASTM D1785.

Wall Cap Concrete Slab

6" (15 cm) Dia. PVC

Sewer Pipe

6" (15 cm) Dia. Metal Duct

Pack tightly with gravel or sand completely

around pipe

3-1/4" x 10" Rectangular to 6" Round Transition

6" (15 cm) Dia. 90 Metal Elbow

6" (15 cm) Dia. Metal Duct

16" (40.6 cm) Max.

12" (30 cm)

Min.

6" (15 cm) Dia. PVC Coupling

6" (15 cm) Dia. PVC Sewer Pipe Elbow

6" (15 cm) Dia. PVC Sewer Pipe Elbow

6" (15 cm) Dia. PVC

Sewer Pipe

6" (15 cm)

Dia. PVC

Coupling 30'-0" (9.14 m) Max.

Optional duct arrangement under concrete slab. PVC duct should be used if installing under a poured concrete slab.

Install ductwork so the piece of duct nearest the downdraft unit slots INTO the next piece of the duct. Secure the joints with self-tapping screws and apply duct tape around the joints to ensure an airtight seal.

Duct Tape Over Seam and Screw

Screw

Air

Flow

Left Discharge

Right Discharge

Down Discharge (as shipped)

49-2000733 Rev. 1 15

1 MOUNT THE UNIT

A Set downdraft into opening. Extend leveling brackets to floor of cabinet so downdraft sits straight. (NOTE: Leveling brackets can be removed and re-attached in other positions. Bottom flange may have to face inward in tight cabinet installations.)

B Secure the downdraft to the countertop as follows: Hold the downdraft against the back of countertop cut-out and tighten the 2 mounting screws (one on each end of unit) on underside of countertop. Use a shim between screw and underside of granite countertops.

The ends of the template may be broken or cut and used as shims if required.

IN STA

LLATIO N

IN STR

U C

TIO N

S Installation Instructions

2 CONNECT POWER Plug power cord into properly grounded receptacle.

1 MOUNT THE UNIT (Cont.) C Screw leveling brackets to bottom of cabinet

using the four wood screws (provided with the unit) on each side.

D Tighten leveling screws through leveling bracket slots to the unit on each side.

E Place cooktop into the countertop cutout. There should be 1/8" minimum gap between the front of the vent trim and the rear of the cooktop.

F Connect duct. Use a roof or wall cap (with damper) that is intended for use with kitchen hoods and vent systems.

3 INSTALL FILTERS, CHECK OPERATION

Press the button on the top cover to raise the vent.

Lift the vent straight up and pull forward. Slide filter into the retainers and close the vent. Turn the knob on the right side of the air vent to

start the blower and adjust the speed. To lower the vent, press the button on the top

cover.

NOTE: It is not necessary to turn the fan OFF before lowering the vent. The fan will automatically turn off when the vent is lowered. When the fan is not turned off before lowering the vent, it will automatically come on at the previously set speed when the vent is fully raised.

Leveling Bracket - Flange Facing Out

Mounting Screws

Leveling Screw

Leveling Screw

Wood Screws

Leveling Bracket - Flange Facing In

Break/Cut the Ends

Bracket

Mounting Screw

Shim

Countertop

16 49-2000733 Rev. 1

TROUBLESHOOTING TIPS TR

O U

B LE

SH O

O TI

N G

T IP

S

Save time and money! Review the charts on the following pages first and you may not need to call for service.

Problem Possible Cause What To Do Fan does not work The vent is not fully extended. Press the button on the top cover. Vent does not work The vent is not plugged into an outlet. Plug the vent into a 120V power outlet.

The button did not engage the lift motor.

Hold down the button for a couple of seconds to activate the motor.

The circuit breaker may have tripped. Check the circuit breaker reset if necessary. Sufficient makeup (replacement) air is required for exhausting appliances to operate to rating.

Check with local building codes, which may require or strongly advise the use of makeup air. Visit GEAppliances.com for available makeup air solutions.

49-2000733 Rev. 1 17

LIM ITED

W A

R R

A N

TY Staple your receipt here. Proof of the original purchase date is needed to obtain service under the w

arranty.

GEAppliances.com All warranty service is provided by our Factory Service Centers, or an authorized Customer Care technician. To schedule service online, visit us at GEAppliances.com/service, or call GE Appliances at 800.GE.CARES (800.432.2737). Please have your serial number and your model number available when calling for service. Servicing your appliance may require the use of the onboard data port for diagnostics. This gives a GE Appliances factory service technician the ability to quickly diagnose any issues with your appliance and helps GE Appliances improve its products by providing GE Appliances with information on your appliance. If you do not want your appliance data to be sent to GE Appliances, please advise your technician not to submit the data to GE Appliances at the time of service.

What GE Appliances will not cover: Service trips to your home to teach you how to use

the product. Improper installation, delivery, or maintenance. Failure of the product if it is abused, misused,

modified, or used for other than the intended purpose or used commercially.

Replacement of house fuses or resetting of circuit breakers.

Damage to the product caused by accident, fire, floods, or acts of God.

Incidental or consequential damage caused by possible defects with this appliance.

Damage caused after delivery. Product not accessible to provide required service. Service to repair or replace light bulbs, except for LED

lamps.

GE Appliances Limited Warranty

EXCLUSION OF IMPLIED WARRANTIES Your sole and exclusive remedy is product repair as provided in this Limited Warranty. Any implied warranties, including the implied warranties of merchantability or fitness for a particular purpose, are limited to one year or the shortest period allowed by law.

For the period of GE Appliances will replace One year From the date of the original purchase

Any part of the cooking product which fails due to a defect in materials or workmanship. During this limited one-year warranty, GE Appliances will provide, free of charge, all labor and related service costs to replace the defective part.

If you received a damaged downdraft vent system Immediately contact the dealer (or builder) that sold you the downdraft vent system.

This limited warranty is extended to the original purchaser and any succeeding owner for products purchased for home use within the USA. If the product is located in an area where service by a GE Appliances Authorized Servicer is not available, you may be responsible for a trip charge or you may be required to bring the product to an Authorized GE Appliances Service location for service. In Alaska, the limited warranty excludes the cost of shipping or service calls to your home. Some states do not allow the exclusion or limitation of incidental or consequential damages. This limited warranty gives you specific legal rights, and you may also have other rights which vary from state to state. To know what your legal rights are, consult your local or state consumer affairs office or your states Attorney General.

Warrantor: GE Appliances, a Haier company Louisville, KY 40225

Extended Warranties: Purchase a GE Appliances extended warranty and learn about special discounts that are available while your warranty is still in effect. You can purchase it online anytime at

GEAppliances.com/extended-warranty

or call 800.626.2224 during normal business hours. GE Appliances Service will still be there after your warranty expires.

18 49-2000733 Rev. 1

Looking For Something More? GE Appliances offers a variety of accessories to improve your cooking and maintenance experiences! Refer to the Consumer Support page for phone numbers and website information. The following products and more are available:

Accessories

Parts Black Stainless Steel Trim (30)

Black Stainless Steel Trim (36)

Cleaning Supplies CitruShine Stainless Steel Wipes

Stainless Steel Appliance Cleaner

A C

C ES

SO R

IE S

49-2000733 Rev. 1 19

Notes

20 49-2000733 Rev. 1

Consumer Support C

O N

SU M

ER S

U PP

O R

T

GE Appliances Website Have a question or need assistance with your appliance? Try the GE Appliances Website 24 hours a day, any day of the year! You can also shop for more great GE Appliances products and take advantage of all our on-line support services designed for your convenience. In the US: GEAppliances.com

Register Your Appliance Register your new appliance on-line at your convenience! Timely product registration will allow for enhanced communication and prompt service under the terms of your warranty, should the need arise. You may also mail in the pre-printed registration card included in the packing material. In the US: GEAppliances.com/register

Schedule Service Expert GE Appliances repair service is only one step away from your door. Get on-line and schedule your service at your convenience any day of the year. In the US: GEAppliances.com/service or call 800.432.2737 during normal business hours.

Extended Warranties Purchase a GE Appliances extended warranty and learn about special discounts that are available while your warranty is still in effect. You can purchase it on-line anytime. GE Appliances Services will still be there after your warranty expires. In the US: GEAppliances.com/extended-warranty or call 800.626.2224 during normal business hours.

Remote Connectivity For assistance with wireless network connectivity (for models with remote enable), visit our website at GEAppliances.com/connect or call 800.220.6899 in the US.

Parts and Accessories Individuals qualified to service their own appliances can have parts or accessories sent directly to their homes (VISA, MasterCard and Discover cards are accepted). Order on-line today 24 hours every day. In the US: GEApplianceparts.com or by phone at 877.959.8688 during normal business hours. Instructions contained in this manual cover procedures to be performed by any user. Other servicing generally should be referred to qualified service personnel. Caution must be exercised, since improper servicing may cause unsafe operation.

Contact Us If you are not satisfied with the service you receive from GE Appliances, contact us on our Website with all the details including your phone number, or write to: In the US: General Manager, Customer Relations | GE Appliances, Appliance Park | Louisville, KY 40225 GEAppliances.com/contact

Escriba los nmeros de modelo y de serie aqu:

N de Modelo ____________

N de Serie ______________

Estos nmeros tambin se encuentran en la Tarjeta de Registro de Propiedad de Producto enviada en forma separada con su sistema de ventilacin de corriente descendente y en la etiqueta que se encuentra en el panel frontal de la unidad.

INFORMACIN DE SEGURIDAD . . . . 3

Uso del Sistema de Ventilacin Sistema De Ventilacin De Corriente Descendente . . . . . . . . . . . . . . . . 5

CUIDADO Y LIMPIEZA Sistema De Ventilacin De Corriente Descendente . . . . . . . . . . . . . . . . 6

INSTRUCCIONES DE INSTALACIN . . . . . . . . . . . . . . . . . . 7

CONSEJOS PARA LA SOLUCIN DE PROBLEMAS . . . . . . . . . . . . . . . . . . . 16

GARANTA LIMITADA . . . . . . . . . . . . . . 17

ACCESORIOS . . . . . . . . . . . . . . . . . . . . . . . . 18

SOPORTE PARA EL CONSUMIDOR . . . . . . . . . . . . . . . . . . 20

GE es una marca registrada de General Electric Company. Fabricado bajo licencia de marca.

UVD6301S UVD6361S

MANUAL DEL PROPIETARIO E INSTALACIN

SI ST

EM A

D E

V EN

TI LA

C I

N d

e co

rr ie

nt e

d es

ce nd

en te

49-2000733 Rev. 1 09-20 GEA

2 49-2000733 Rev. 1

GRACIAS POR HACER QUE GE APPLIANCES SEA PARTE DE SU HOGAR.

Ya sea que haya crecido usando GE Appliances, o que sta es su primera vez, nos complace tenerlo en la familia.

Sentimos orgullo por el nivel de arte, innovacin y diseo de cada uno de los electrodomsticos de GE Appliances, y creemos que usted tambin. Entre otras cosas, el registro de su electrodomstico

asegura que podamos entregarle informacin importante del producto y detalles de la garanta cuando los necesite.

Registre su electrodomstico GE ahora a travs de Internet. Sitios Web y nmeros telefnicos tiles estn disponibles en la seccin de Soporte para el Consumidor de este Manual del Propietario.

Tambin puede enviar una carta en la tarjeta de inscripcin preimpresa que se incluye con el material embalado.

49-2000733 Rev. 1 3

IN FO

R M

A C

I N

D E SEG

U R

ID A

D INFORMACIN IMPORTANTE DE SEGURIDAD LEA TODAS LAS INSTRUCCIONES ANTES DE USAR

LEA Y GUARDE ESTAS INSTRUCCIONES

ADVERTENCIA PARA REDUCIR EL RIESGO DE INCENDIO, DESCARGA ELCTRICA O LESIONES A PERSONAS, CUMPLA CON LOS SIGUIENTES PUNTOS: A. Utilice esta unidad slo de la manera concebida por el

fabricante. Si tiene alguna pregunta, comunquese con el fabricante.

B. Antes de realizar reparaciones o limpiar la unidad, desconecte la energa del panel de servicio y bloquee los medios de desconexin para evitar el accionamiento de la energa de manera accidental. Cuando los medios de desconexin de servicio no pueden bloquearse, coloque sobre el panel de servicio un dispositivo de advertencia bien visible, como una etiqueta.

C. No utilice esta unidad con ningn dispositivo de control de velocidad de estado slido.

D. Enchufe el sistema de ventilacin en un tomacorriente con conexin a tierra de 120 voltios nicamente. No retire la pata redonda de conexin a tierra del enchufe. Si tiene dudas sobre la conexin a tierra del sistema elctrico para hogar, es su responsabilidad y obligacin contar con el reemplazo de un tomacorriente sin conexin a tierra por un tomacorriente de tres patas correctamente conectado a tierra, de acuerdo con el Cdigo Nacional de Electricidad. No use prolongadores con este electrodomstico.

PRECAUCIN SLO PARA USO DE VENTILACIN GENERAL. NO LO UTILICE PARA ELIMINAR MATERIALES Y VAPORES PELIGROSOS O EXPLOSIVOS.

ADVERTENCIA PARA REDUCIR EL RIESGO DE LESIONES A PERSONAS EN CASO DE UN INCENDIO DE GRASA SOBRE UNA ESTUFA, CUMPLA CON LOS SIGUIENTES PUNTOS*: A. APAGUE LAS LLAMAS con una tapa que ajuste bien,

una plancha para galletas o una bandeja de metal, y luego apague el quemador. TENGA MUCHO CUIDADO A FIN DE EVITAR QUEMADURAS. Si las llamas no se apagan de inmediato, SALGA DE LA VIVIENDA Y LLAME AL DEPARTAMENTO DE BOMBEROS.

B. NUNCA LEVANTE UNA SARTN EN LLAMAS Usted puede quemarse.

C. NO UTILICE AGUA, incluyendo repasadores o toallas hmedosse provocar una violenta explosin de vapor.

D. Utilice un extintor SLO si: 1. Usted sabe que cuenta con un extintor Clase ABC y

ya sabe cmo utilizarlo. 2. El incendio es pequeo y se contuvo en el rea donde

comenz. 3. Se est llamando al departamento de bomberos. 4. Usted puede combatir el incendio con su espalda

dirigida hacia una salida. * Basado en Kitchen Fire Safety publicado por NFPA.

ADVERTENCIA PARA REDUCIR EL RIESGO DE UN INCENDIO DE GRASA SOBRE UNA ESTUFA: A. Nunca deje unidades de superficie desatendidas en

configuraciones de calor elevadas. Los alimentos que hierven y se derraman provocan humo y derrames grasosos que pueden prenderse fuego. Caliente los aceites lentamente en configuraciones bajas o medias.

B. Siempre encienda el sistema de ventilacin cuando cocine con configuraciones de calor elevadas o cuando flambee alimentos (por ej., Crepes Suzette, cerezas Jubilee, carne flambeada a la pimienta en grano).

C. Limpie los ventiladores con frecuencia. No debe permitirse la acumulacin de grasa en el ventilador o en el filtro.

D. Utilice el tamao de recipiente adecuado. Siempre utilice recipientes de coccin apropiados para el tamao del elemento de superficie.

Si necesita servicio tcnico No intente reparar o cambiar ninguna pieza del sistema de ventilacin, a menos que est especficamente recomendado en este manual. Cualquier otro servicio debe realizarlo un tcnico calificado. Asegrese de cortar la electricidad antes de efectuar servicio tcnico en el aparato. Puede resultar necesario quitar el sistema de ventilacin para realizar servicio tcnico en componentes tales como el motor del ventilador o el mecanismo de ventilacin de aire. Desconecte la energa que alimenta la estufa y qutela en primer trmino. Invierta los pasos de la seccin Cmo instalar la ventilacin descendente en las Instrucciones de instalacin para quitar el ventilador. Las piezas para el servicio tcnico se encuentran disponibles en el Centro de Servicio Tcnico y Piezas de GE Appliances. Cuando baje la ventilacin, mantenga los dedos alejados de la parte superior del sistema de ventilacin.

4 49-2000733 Rev. 1

Cmo Retirar la Pelcula Protectora de Envo y la Cinta de Embalaje Con cuidado tome un extremo de la pelcula protectora de envo con los dedos y lentamente retire la misma de la superficie del electrodomstico. No utilice ningn producto filoso para retirar la pelcula. Retire toda la pelcula antes de usar el electrodomstico por primera vez.

Para asegurar que no haya daos sobre el acabado del producto, la forma ms segura de retirar el adhesivo de la cinta de embalaje en electrodomsticos nuevos es aplicando un detergente lquido hogareo para lavar platos. Aplique con una tela suave y deje que se seque.

NOTA: El adhesivo deber ser eliminado de todas las partes. No se puede retirar si se hornea con ste dentro.

ATENCIN: Por favor retire el envoltorio de burbujas insertado en el escape antes de la instalacin. Asegrese de que no quede nada dentro de la caja del ventilador.

IN FO

R M

A C

I N

D E

SE G

U R

ID A

D INFORMACIN IMPORTANTE DE SEGURIDAD LEA TODAS LAS INSTRUCCIONES ANTES DE USAR

LEA Y GUARDE ESTAS INSTRUCCIONES

Envoltorio de Burbujas

49-2000733 Rev. 1 5

Sistema De Ventilacin De Corriente Descendente U

so del Sistem a de Ventilacin: Sistem

a de ventilacin de corriente descendente

Cuando Utilice el Sistema de Ventilacin PRECAUCIN Tenga cuidado al levantar o bajar

la ventilacin. Asegrese de que las cacero las, las manijas de las cacerolas y otros objetos se encuentren alejados de la ventilacin y que no se golpeen o vuelquen cuando se la eleve. NOTA: Hay una pequea saliente en cada lado de la ventilacin.

tapa de la ventilacin cuando se la baje.

piezas de la ventilacin.

IMPORTANTE: Si la ventilacin queda obstruida con un objeto mientras se la sube o baja, sta se detendr. Con cuidado retire la obstruccin y la ventilacin descender hasta la posicin que se desea bajar. Vuelva a presionar el botn para regresar a las funciones normales.

Sistema De Ventilacin De Corriente Descendente A fin de elevar la ventilacin descendente, presione el botn de la tapa superior. La ventilacin se elevar.

El ventilador se podr girar a ON (Encender) y OFF (Apagar) y la velocidad se podr ajustar con la perilla empotrada sobre el lado derecho de la salida de aire. Si se lo deja encendido, el ventilador se apagar automticamente cuando se baje la ventilacin. NOTA: Para un funcionamiento ms conveniente, configure el ventilador a la velocidad que utilice ms a menudo. El ventilador se accionar a esta velocidad cuando la unidad se eleve. Baje la ventilacin descendente presionando el botn de la tapa superior. La ventilacin descender y el ventilador se apagar.

Consejos De Coccin El elevado movimiento de aire de este sistema de ventilacin puede aumentar los tiempos de coccin de algunos alimentos. Puede tomar ms tiempo alcanzar temperaturas de coccin elevadas si se acciona la ventilacin en la configuracin alta desde el comienzo. Para mejores resultados de coccin, ajuste la velocidad del ventilador.

Para mejores resultados cuando caliente aceite para frer o cuando hierva agua, utilice las unidades de superficie frontales o espere a que el agua est hirviendo o a que el aceite se encuentre a temperatura de fritura antes de accionar el sistema de ventilacin. Es posible que el sistema de ventilacin no capture por completo todo el vapor proveniente de las ollas de los quemadores frontales.

Botn

6 49-2000733 Rev. 1

C U

ID A

D O

Y L

IM PI

EZ A

: S is

te m

a de

v en

til ac

i n

de c

or rie

nt e

de sc

en de

nt e Sistema De Ventilacin De Corriente Descendente

Superficies Pintadas O De Acero Inoxidable No utilice almohadillas de acero porque rayan la superficie. Para limpiar la superficie de acero inoxidable, utilice agua tibia jabonosa o un limpiador o lustrador para acero inoxidable. Siempre limpie la superficie en direccin de la veta. Siga las instrucciones del producto para limpiar la superficie de acero inoxidable. En caso de haber manchas difciles de quitar sobre el acero inoxidable, use un limpiador que contenga cido lctico o cido ctrico.

Para realizar consultas sobre la adquisicin de productos, incluyendo limpiadores o pulidores para electrodomsticos de acero inoxidable, lea las secciones de Asistencia y Accesorios, en el comienzo de este manual.

Filtros De Grasa La eficiencia del sistema de ventilacin depende de la limpieza del filtro. La frecuencia de limpieza depende del tipo de coccin que realice. Los filtros de grasa deben limpiarse por lo menos una vez por mes. Nunca opere el sistema de ventilacin si los filtros no estn colocados correctamente. Para quitar: Retire los filtros de la salida de aire, llegando hasta los mismos a travs de la abertura de la ventilacin, presionando hacia abajo y luego hacia afuera. NOTA: Los filtros poseen diferentes tamaos. Asegrese de reemplazarlos una vez retirados, colocando el ms ancho sobre la izquierda. Para limpiar: Sumerja y luego agite en una solucin de detergente caliente. Puede utilizarse un cepillo suave para quitar la suciedad muy adherida. Enjuague, agite y quite la humedad antes de volver a colocar. No lave los filtros en el lavavajillas. Con una manipulacin cuidadosa, el filtro durar muchos aos. Si necesita reemplazarlo, solicite el repuesto a su vendedor.

Lengetas del filtro

49-2000733 Rev. 1 7

Preguntas? Llame al 800.GE.CARES (800.432.2737) o visite nuestro sitio Web en: GEAppliances.com

Instrucciones de instalacin

IN STR

U C

C IO

N ES D

E IN STA

LA C

I N

Sistemas de Ventilacin de Aire Descendente

UVD6301S, UVD6361S

ANTES DE COMENZAR Lea estas instrucciones por completo y con detenimiento. IMPORTANTE Guarde estas instrucciones

para el uso de inspectores locales.

IMPORTANTE Cumpla con todos los cdigos y ordenanzas vigentes.

Nota al instalador Asegrese de dejar estas instrucciones con el consumidor.

Nota al consumidor Conserve estas instrucciones para referencias futuras.

Nivel de capacidad La Instalacin de este electrodomstico debe ser realizada por un instalador calificado o por un electricista.

El instalador tiene la responsabilidad de efectuar una instalacin adecuada.

La Garanta no cubre las fallas del producto debido a una instalacin incorrecta.

INSTRUCCIONES PARA DESCARGA A TIERRA Este electrodomstico debe estar conectado a tierra. En caso de que se produzca un cortocircuito, la conexin a tierra reduce el riesgo de descarga elctrica, brindando un cable de escape de la corriente elctrica. Este electrodomstico est equipado con un cable de corriente que posee un cable de conexin a tierra con un enchufe a tierra. El enchufe se deber colocar en un tomacorriente instalado y conectado a tierra de forma adecuada.

ADVERTENCIA Una conexin a tierra inadecuada puede producir riesgos de descargas elctricas. Consulte a un electricista calificado en caso de que las instrucciones de conexin a tierra no se entiendan completamente, o si tiene dudas sobre si el electrodomstico est conectado a tierra de forma apropiada. No use un prolongador. Si el cable de corriente es demasiado corto, solicite a un electricista calificado que instale un tomacorriente cerca del electrodomstico. Si el sistema de ventilacin que recibi est daado, se deber comunicar con su vendedor minorista.

QUITE EL EMPAQUE Retire los materiales embalados y el cartn; deje a un lado el cartn. El cartn puede ser usado como base al cambiar o ajustar la direccin de la ventilacin.

HERRAMIENTAS Y MATERIALES REQUERIDOS Gafas de seguridad Destornillador con cabeza plana largo Sierra de vaivn Regla de carpintero Tubera adecuada para la instalacin Nivel

PIEZAS PROVISTAS Abra el cartn y retire el paquete de piezas. Controle los contenidos a fin de asegurar que todas las piezas estn presentes.

Soportes de Estabilizacin - Cant.: 2

Filtros - unidad interior - Cant.: 2

Tornillo de Montaje de la Mesada 1/4-20

x 2.00 Cab. Hex. Cant.: 2

Plantilla de Plstico (adherida al producto)

Cant.: 1

Tornillo de Nivelacin de

Cada, 1/4-20 x .50 Cab. Hex. -

Cant.: 2

Tornillo de madera, n 8 x.750

SI Redondo - Cant.: 4

28.5 for 30 Models 34 for 36 Models 28.5 para odelos de 30

34 para Modelos de 36

8 49-2000733 Rev. 1

Informacin de Seguridad IN

ST R

U C

C IO

N ES

D E

IN ST

A LA

C I

N

ADVERTENCIA PARA REDUCIR EL RIESGO DE INCENDIO, DESCARGA ELCTRICA O LESIONES A PERSONAS, CUMPLA CON LOS SIGUIENTES PUNTOS: El trabajo de instalacin y el cableado elctrico deben

ser realizados por una persona(s) calificada de acuerdo con todos los cdigos y estndares aplicables, incluyendo construcciones resistentes al fuego.

Es necesario contar con suficiente cantidad de aire para una combustin y salida de gases adecuadas a travs del conducto (chimenea) del equipo de consumo de combustible, a fin de evitar rfagas de aire. Siga las pautas del fabricante del equipo de calefaccin y los estndares de seguridad, tales como aquellos publicados por la Asociacin Nacional de Proteccin contra Incendios (National Fire Protection Association, NFPA), la Sociedad Estadounidense para la Calefaccin (American Society for Heating), los Ingenieros de Refrigeracin y Acondicionadores de Aire (Refrigeration and Air Conditioning Engineers, ASHRAE) y las autoridades de los cdigos locales.

Al cortar o perforar una pared o un cielorraso, no dae el cableado elctrico y de otros servicios ocultos.

Los ventiladores con conducto siempre deben contar con ventilacin hacia el exterior.

PRECAUCIN PARA REDUCIR EL RIESGO DE INCENDIO Y PARA ELIMINAR EL AIRE DE ESCAPE CORRECTAMENTE, ASEGRESE DE DIRIGIR EL AIRE DEL CONDUCTO HACIA EL EXTERIOR. NO VENTILE EL AIRE DE ESCAPE EN ESPACIOS DENTRO DE PAREDES O CIELORRASOS O EN TICOS, HUECOS SANITARIOS O GARAJES.

ADVERTENCIA A FIN DE REDUCIR EL RIESGO DE INCENDIOS, USE SLO CONDUCTOS DE METAL. Cuando corresponda, instale un sistema de reposicin

(reemplazo) de aire de acuerdo con los requisitos del cdigo local de construccin. Para acceder a soluciones relacionadas con la reposicin de aire, visite GEAppliances.com.

La tubera de cloaca de PVC puede ser usada como conducto bajo una losa de concreto, si esto lo permite la junta del cdigo local.

49-2000733 Rev. 1 9

Preparacin para la instalacin IN

STR U

C C

IO N

ES D E IN

STA LA

C I

N

SUMINISTRO DE ENERGA Esta ventilacin de aire descendente debe ser provista con 120V, 60 Hz, y estar conectada a un circuito de empalmes individual correctamente conectado a tierra, protegido por un disyuntor o fusible de retardo de 15 o 20 amp. Un receptculo de 3 clavijas correctamente conectado a tierra debe estar dentro del alcance del cable de corriente de dos pies de la ventilacin. Superficies de Coccin a Gas Si esta ventilacin es instalada junto con una superficie

de coccin a gas de GE o Monogram, puede funcionar desde el mismo tomacorriente doble.

Superficies de Coccin Elctricas Si esta ventilacin es instalada junto con una superficie

de coccin elctrica de GE o Monogram, la ventilacin debe funcionar desde un tomacorriente de 120V aparte.

Ubique el receptculo dentro del gabinete en la pared lateral derecha (vea la ilustracin). El receptculo no puede ser colocado en la parte trasera de la pared del gabinete, donde puede interferir con el plenum de aire descendente. El cable de corriente de la ventilacin de aire descendente se debe conducir por debajo de la superficie de coccin y alejado del calor generado por esta ltima. Asegrese de que la superficie de coccin sea instalada de acuerdo con las instrucciones de instalacin del fabricante.

IMPORTANTE (Tenga a bien leer cuidadosamente) El cable de corriente de este electrodomstico cuenta con un enchufe de 3 clavijas (con cable a tierra) que se conecta a un receptculo de pared con conexin a tierra de tres clavijas para minimizar la posibilidad de descargas elctricas. El cliente deber solicitar a un electricista calificado que controle el receptculo de pared y el circuito, a fin de asegurar que el receptculo est adecuadamente conectado a tierra y que cuente con la polaridad correcta. En caso de contar con un receptculo de pared de dos

clavijas, es responsabilidad y obligacin del cliente reemplazarlo por un tomacorriente de pared de tres clavijas correctamente conectado a tierra.

Nunca, bajo ninguna circunstancia, corte o elimine el tercer cable (tierra) del cable de corriente. No use prolongadores ni adaptadores con este electrodomstico. Siga el Cdigo Nacional de Electricidad o los cdigos y ordenanzas locales establecidos. Ubicacin de la Etiqueta de Clasificacin en el frente del chasis del sistema de ventilacin.

VOLTIOS AMPERIOS CONDUCTO 120 4.0 3-1/4 X 10

ESPECIFICACIONES

NO Ubique las Conexiones de Gas o Elctricas dentro de esta rea

34" (ancho del recorte) para modelos de 36 28-1/2" (ancho del recorte) para modelos de 30

29-1/2"

12"

Toma- corriente

Elctrico de 12 sobre el Piso del Gabinete

Ubique la conexin de gas o electricidad slo dentro del

rea sombreada.

10 49-2000733 Rev. 1

Preparacin para la instalacin IN

ST R

U C

C IO

N ES

D E

IN ST

A LA

C I

N

DIMENSIONES DEL PRODUCTO A B

30" Modelos 30" 26-1/4 36" Modelos 36" 32-1/4

2

2-1/2

7

7-1/4

36-1/2

A

B

22.3

49-2000733 Rev. 1 11

IN STR

U C

C IO

N ES D

E IN STA

LA C

I N

Preparacin para la instalacin

PREPARANDOSE PARA LA INSTALACIN Desembale la superficie de coccin y lea las Instrucciones

de Instalacin a fin de entender las dimensiones necesarias requeridas para la mesada y su ubicacin, el espacio entre la superficie de coccin y el extremo frontal de la mesada, y los despejes necesarios con los gabinetes y paredes. El ancho del espacio requerido para el sistema de ventilacin se muestra en la pgina 9. Confirme que haya suficiente espacio entre un lado y otro para contar con los espacios y despejes necesarios para la superficie de coccin.

Utilizando las siguientes ilustraciones y tomando las medidas de la superficie de coccin para establecer la dimensin A, confirme que haya suficiente espacio entre el frente y la parte trasera (dimensin B) para colocar tanto la superficie de coccin como el sistema de ventilacin. Observe que el extremo trasero de la superficie de coccin se superpondr con la superficie frontal del sistema de ventilacin (consulte la Pgina 10).

De ser necesario ms espacio para la mesada, consulte la seccin de Soluciones Creativas en la pgina 13.

Utilizando las ilustraciones en las pginas 9 y 12 y tomando las medidas del sistema de ventilacin y la ubicacin de la salida de la ventilacin, confirme los espacios necesarios dentro del gabinete, la direccin del escape de la ventilacin, y la alineacin del escape de la ventilacin con el conducto. De ser necesario para el despeje o la alineacin del enlace del conducto, reposicione la ubicacin de la superficie de coccin, o modifique la ubicacin de los muebles, o la tubera.

Confirme que los receptculos elctricos y las tuberas de gas estn correctamente ubicadas, y vuelva a ubicar las mismas de ser necesario.

B

C

B es la dimensin mnima de la parte plana de la mesada que es necesaria

A

A es la dimensin desde la cabeza del tornillo en la superficie frontal de la base de la superficie de coccin hasta el extremo trasero de la superficie de coccin. Si no puede encontrar la dimensin

A en las instrucciones de instalacin de la superficie de coccin, entonces deber medirla.

La profundidad del recorte es A + 2 1/8 La profundidad mnima de la mesada es B = A + C + 2.5

La dimensin C est definida en las Instrucciones de Instalacin de la superficie de coccin

SUPERFICIE DE COCCIN

Mnimo de 1/8

Extremo frontal de la mesada

Frente del recorte en la mesada

Cabeza del tornillo Extremo

frontal de la superficie de coccin

Frente del recorte en la mesada

Extremo trasero de la superficie de coccin

Parte Trasera del Recorte en la mesada

2 1/8

Mnimo de 3/8

V e n t i l a c i n d e A i r e D e s c e n d e n t e

Mesada

Tapa del Motor del Engranaje

Caja del Ventilador

Superficie de Coccin Caperuza de Chimenea

Salida de Aire

Tomacorriente con Conexin a Tierra de 120 VAC

Conector del Conducto de 3 x 10

12 49-2000733 Rev. 1

Preparacin para la instalacin IN

ST R

U C

C IO

N ES

D E

IN ST

A LA

C I

N

OPCIONES DE VENTILACIN La ventilacin de aire hacia abajo es enviada con el

tomacorriente de descarga apuntando hacia abajo y puede ser modificada hacia el lado izquierdo o derecho. A fin de evitar problemas de interferencias, la descarga de corriente descendente no podr ser ventilada hacia la derecha, cuando se instale con una superficie de coccin a gas de GE o Monogram, o con una superficie de coccin elctrica que no sea de induccin de GE o Monogram.

El tomacorriente del calefactor est ajustado para la medida de 3 1/4 x 10 y puede ser modificado hasta 6.

El ventilador se enva con su descarga mirando hacia ABAJO. Siga estos pasos NICAMENTE si: es necesario mover la posicin de descarga del ventilador,

de modo que el conducto no interfiera con viguetas de pisos, tuberas o cableados que pasen por debajo.

es necesario rotar la descarga del ventilador hacia la DERECHA o IZQUIERDA.

Coloque la unidad sobre su parte trasera en una mesa o superficie de trabajo. Haga fuerza hacia afuera para retirar la lmina del envoltorio de burbujas. Asegrese de que no quede nada dentro.

DESCARGA DESCENDENTE MOVIMIENTO DEL VENTILADOR HACIA LA IZQUIERDA O DERECHA

1. Afloje las 4 tuercas y los 2 canales de abrazaderas. 2. Retire los 5 tornillos de la parte inferior. Estos 5 tornillos

son de embalaje y no es necesario volver a ajustarlos. 3. Deslice el ventilador hasta la posicin deseada. 4. Use la placa de la tapa suministrada para cerrar el

espacio abierto (si lo hay). 5. Ajuste las tuercas de mariposa para asegurar el ventilador

y ajuste los tornillos de la lmina metlica a travs de la brida inferior a fin de asegurar la parte inferior del ventilador

DESCARGA HACIA LA IZQUIERDA O DERECHA

1. Retire las 4 tuercas y los 2 canales de abrazaderas. 2. Retire los 5 tornillos de la parte inferior. Estos 5 tornillos

son de embalaje y no es necesario volver a ajustarlos. 3. Con cuidado levante el ventilador y desconecte el enchufe

del motor, de ser necesario. Vuelva a posicionar el ventilador y RECONECTE EL ENCHUFE DEL MOTOR.

4. Use la placa de la tapa suministrada para cerrar el espacio abierto (si lo hay).

5. Reemplace los canales de la abrazadera y use las tuercas para asegurar el soplador en su nueva posicin.

6. Use los tornillos de la lmina metlica a travs de la brida inferior a fin de asegurar la parte inferior del soplador.

Para un mejor funcionamiento: elija la opcin de tubera que permita la longitud ms corta y el mnimo nmero de codos y transiciones. Controle la ubicacin de las viguetas del piso, montajes de pared, cableado elctrico y plomera para evitar posibles interferencias. NOTA: La unidad se enva con la descarga de 3 x 10" hacia ABAJO. Consulte el CAMBIO DE DIRECCIN DEL VENTILADOR en la pgina 3, de ser necesario. El sistema funcionar de forma ms eficiente cuando el conducto no supere los 40 pies del conducto equivalente. El cuadro que aparece a continuacin muestra los pies equivalentes de los codos y las transiciones. El nmero de pies del conducto recto ms los pies equivalentes de las transiciones y/o codos que se usarn deber ser igual a 40 pies o menos.

Tuercas Ventilador

Canal de la Abrazadera

Tornillos Metlicos de la Lmina

Brida Inferior

Codo Redondeado

de 6

Transicin Redondeada de 3

x 10 a 6

Codo de 90 de 3 x 10

igual a 6 pies de conducto

recto

igual a 2 pies de conducto recto

igual a 8 pies de conducto

recto

Lmina del Envoltorio de Burbujas

Enchufe del Motor

Tornillo Metlicos de la Lmina

Tuercas

Canal de la Abrazadera

Ventilador

Brida Inferior

49-2000733 Rev. 1 13

IN STR

U C

C IO

N ES D

E IN STA

LA C

I N

Instrucciones de instalacin

SOLUCIONES CREATIVAS Cuando el diseo de

la cocina requiera una instalacin contra la pared, mueva el gabinete de la base hacia delante entre 3 y 5. Los paneles de relleno o las molduras complementarias pueden ser agregadas a los costados expuestos de los gabinetes.

En una isla o pennsula, use una mesada extra profunda. La parte saliente del frente de la mesada puede ser ajustada para cumplir con los requisitos entre el mueble lindero y el espacio de recorte.

Cuando el espacio de recorte requerido hasta el extremo frontal de la mesada sea superior a 2, agregue un borde redondeado al extremo frontal de la mesada. Incluya el ancho del borde al medir el espacio requerido desde el extremo frontal hasta el recorte. Al agregar el borde, la superficie de coccin puede ser movida hacia delante,

brindando profundidad adicional a la mesada y al espacio interno de los gabinetes.

Cuando las distancias entre la ventilacin y las paredes laterales internas de los gabinetes sean superiores a 5 y/o la pared trasera del gabinete interno sea superior a 4 , se debern construir paredes falsas dentro del gabinete para asegurar la ventilacin con los soportes de estabilizacin (consulte los Recortes y Despejes en Preparacin de la Instalacin).

PREPARACIN DE LA MESADA Apoye y corte el recorte de la superficie de coccin lo suficiente HACIA DELANTE de modo que la cada se ajuste detrs de ste. 1. Configure la superficie de

coccin en su posicin y deslice la misma tan hacia delante como sea posible. Centre y cuadre la misma con los extremos o la mesada.

2. Coloque la plantilla de plstico contra la brida trasera de la superficie de coccin y centre la misma. Realice un trazado alrededor de la plantilla para marcar la abertura descendente.

3. Retire la superficie de coccin de la mesada. 4. Corte la abertura descendente. Tenga cuidado de no

astillar los extremos de la mesada.

Gabinete de la Base

Panel de Relleno

Lavabo de la Base

Panel de Relleno

Mantenga los Espacios de Despeje hasta el Extremo Frontal de Acuerdo con lo Especificado

Panel de Cobertura

Panel Final

Se Debe Mantener la Parte Saliente de la Mesada para Contar con los Despejes de la Superficie de Coccin

14 49-2000733 Rev. 1

PREPARACIN DEL CONDUCTO Determine el mejor recorrido para el conducto; el mismo puede ser conducido de diferentes formas dependiendo del esquema de la cocina. IMPORTANTE: La salida de la descarga de aire descendente para esta unidad es rectangular, y con una medida de 3 x 10. Planifique el recorrido de forma consecuente. Serie de mesadas con distribucin tpica de tuberas.

A fin de maximizar el rendimiento de la ventilacin del sistema de ventilacin: 1. Minimice la longitud del conducto y el nmero de

transiciones y codos. 2. Mantenga un tamao de conducto constante. 3. Selle todas las juntas con cinta para conductos a fin de

evitar prdidas. 4. No utilice conductos flexibles de ningn tipo.

Preparacin para la instalacin IN

ST R

U C

C IO

N ES

D E

IN ST

A LA

C I

N

Pared interna del gabinete

Pared interna hacia arriba hasta el techo o la parte saliente

Directamente hacia el exterior

Entre vigas del piso A travs del espacio de las patas del gabinete

Pennsula o una isla

Pennsula

Pared externa del gabinete

Arreglo opcional del conducto bajo una losa de concreto. Se deber usar un conducto de PVC si se instalar bajo una losa de concreto.

Instale la tubera de modo que el trozo de conducto ms cercano a la unidad de ventilacin de aire descendente encaje DENTRO DE la siguiente pieza del conducto. Asegure las uniones con tornillos autorroscantes y coloque cinta para conductos alrededor de las uniones, a fin de sellar la salida de aire.

NOTA: Tubera de cloaca de PVC tipo PSM 12454-B Norma 40 ASTM D1785.

Tapa de Pared Losa de Concreto

Tubera de Cloaca de PVC

de6(15 cm) de Dim.

Conducto Metlico de

6 (15 cm) de Dim.

Embale de forma bien ajustada con grava o arena completamente

alrededor de la tubera.

Transicin Rectangular de 3 x 10 a Circular de 6Codo Metlico de

6 (15 cm) de Dim. y 90

Conducto Metlico de 6 (15 cm) de Dim.

Mx. de 16(40.6 cm)

Mn. de 12(30 cm)

Acople de PVC de 6(15 cm) de Dim.

Codo para Tubera de Cloaca de 6 (15 cm) de Dim.

Codo para Tubera de Cloaca de 6(15 cm) de Dim.

Tubera de Cloaca

de PVC de 6(15 cm)

de Dim.

Acople de PVC de

6(15 cm) de Dim.

Mx. de 30-0(9.14 m)

Cinta para Conducto sobre la Unin y el Tornillo

Tornillo

Flujo

de Aire

Descarga Izquierda

Descarga Derecha

Descarga Descen- dente (como se enva)

49-2000733 Rev. 1 15

IN STR

U C

C IO

N ES D

E IN STA

LA C

I N

Instrucciones de instalacin

2 CONECTE LA CORRIENTE Enchufe el cable de corriente en un receptculo correctamente conectado a tierra.

3 INSTALE LOS FILTROS, CONTROLE EL FUNCIONAMIENTO

Presione el botn de la tapa superior para elevar la ventilacin.

Levante la ventilacin hacia arriba y empuje hacia delante. Deslice el filtro sobre los tensores y cierre la ventilacin. Gire la perilla sobre el lado derecho de la salida de

aire para activar el ventilador y ajuste la velocidad. A fin de bajar la ventilacin, presione el botn de la

tapa superior.

NOTA: No es necesario apagar el ventilador antes de bajar el nivel de ventilacin. El ventilador se apagar de forma automtica cuando la ventilacin se baje. Cuando el ventilador no es apagado antes de bajar el nivel de ventilacin, el mismo ir de forma automtica a la velocidad configurada previamente cuando la ventilacin se incremente hasta el mximo.

1 MONTA LA UNIDAD

A Configure la cada en la abertura. Extienda los soportes de nivelacin hasta el piso del gabinete de modo que la cada se apoye de forma recta. (NOTA: Los soportes de nivelacin se podrn retirar y volver a adherir en otras posiciones. Es posible que la brida inferior mire hacia adentro en instalaciones de gabinetes ajustadas).

B Asegure la cada hasta la mesada del siguiente modo: sostenga la cada contra la parte trasera del recorte de la mesada y ajuste los 2 tornillos de montaje (uno en cada extremo de la unidad) sobre la parte inferior de la mesada. Use una cua entre el tornillo y la parte inferior en mesadas de granito.

Los extremos de la plantilla se podrn romper o ser cortados y usados como cuas, de ser necesario.

Rompa/ Corte los Extremos

1 MONTA LA UNIDAD (Cont.) C Soportes de nivelacin de tornillos en la parte inferior

del gabinete usando los cuatro tornillos de madera (provistos con la unidad) a cada lado.

D Ajuste los tornillos de nivelacin a travs de las ranuras del soporte de nivelacin a la unidad sobre cada lado.

E Coloque la superficie de coccin en el espacio libre de la mesada. Deber haber una brecha mnima de 1/8 entre el frente del marco de ventilacin y la parte trasera de la superficie de coccin.

F Conecte el conducto. Use una tapa de techo o de pared (con regulador) diseada para uso con campanas de cocina y sistemas de ventilacin.

Soporte de Nivelacin Brida Mirando Hacia Afuera

Tornillos de Montaje

Tornillo de Nivelacin

Tornillo de Nivelacin

Tornillos de Madera

Soporte de Nivelacin Brida Mirando Hacia

Adentro

Soporte

Tornillo de Montaje

Cua

Mesada

16 49-2000733 Rev. 1

Consejos para la Solucin de Problemas... Antes de solicitar el servicio tcnico Ahorre tiempo y dinero! Primero revise los cuadros que aparecen en las siguientes pginas y es posible que no necesite solicitar reparaciones.

Problema Causa Posible Qu hacer El ventilador no funciona

El ventilador no est extendido por completo. Presione el botn de la tapa superior.

La ventilacin no funciona

La ventilacin no est enchufada en un tomacorriente.

Enchufe la ventilacin en un tomacorriente de 120V.

Presione el botn de la tapa superior. Mantenga presionado el botn durante un par de segundos para activar el motor.

El interruptor de circuitos puede haber saltado.

Verifique el interruptor de circuitos y reconfigrelo si fuera necesario.

Se requiere suficiente reposicin (reemplazo) de aire para que los artefactos con salida de aire funcionen de acuerdo con sus calificaciones energticas.

Controle los cdigos locales de construccin, que podrn requerir o aconsejar enfticamente el uso de reposicin de aire. Para acceder a soluciones de aire disponibles, visite GEAppliances.com.

C O

N SE

JO S

PA R

A LA

S O

LU C

I N

D E

PR O

B LE

M A

S

49-2000733 Rev. 1 17

Ab ro

ch e

su re

ci bo

a qu

. Pa

ra a

cc ed

er a

l s er

vi ci

o t

cn ic

o de

a cu

er do

c on

la

g ar

an ta

d eb

er

co nt

ar c

on la

p ru

eb a

de la

fe ch

a or

ig in

al d

e co

m pr

a.

GEAppliances.com Todo el servicio de garanta es provisto por nuestros Centros de Servicio de Fabricacin, o un tcnico autorizado de Customer Care. Para programar una visita del servicio tcnico a travs de Internet, vistenos en www.geappliances.com/service_and_support/, o llame al 800.GE.CARES (800.432.2737). Cuando llame para solicitar el servicio, tenga los nmeros de serie y modelo disponibles. Para realizar el servicio tcnico de su electrodomstico, se podr requerir el uso de datos del puerto de abordaje para su diagnstico. Esto da al tcnico del servicio de fbrica de GE Appliances la habilidad de diagnosticar de forma rpida cualquier problema con su electrodomstico, y de ayudar a GE Appliances a mejorar sus productos al brindarle a GE Appliances la informacin sobre su electrodomstico. Si no desea que los datos de su electrodomstico sean enviados a GE Appliances, solicitamos que le indique a su tcnico no entregar los datos a GE Appliances en el momento del servicio.

Qu no cubrir GE Appliances: Viajes del tcnico del servicio a su hogar para ensearle

sobre cmo usar el producto.

o uso para propsitos diferentes al original o uso comercial.

incendio, inundaciones o catstrofes naturales.

defectos sobre este producto.

superficie, deslustres o manchas pequeas no informadas dentro de las 48 horas luego de la entrega.

la superficie) que pueden ser eliminadas siguiendo las instrucciones de limpieza.

lmparas, excepto las lmparas LED.

G A

R A

N T

A Garanta de GE Appliances

EXCLUSIN DE GARANTAS IMPLCITAS Su nica y exclusiva alternativa es la reparacin del producto, como se indica en la Garanta Limitada. Las garantas implcitas, incluyendo garantas implcitas de comerciabilidad o conveniencia sobre un propsito particular, se limitan a un ao o al perodo ms corto permitido por la ley.

Por el Perodo de GE Appliances reemplazar Un Ao Desde la fecha de la compra original

Cualquier pieza del producto de coccin que falle debido a un defecto en los materiales o la fabricacin. Durante esta garanta limitada de un ao, GE Appliances tambin proveer, sin costo, todo el trabajo y costos del servicio relacionados con el reemplazo de la pieza defectuosa.

Si usted recibi un sistema de ventilacin de corriente descendente averiado Comunquese de inmediato con el vendedor (o constructor) que le vendi el sistema de ventilacin de corriente descendente.

Esta garanta limitada se extiende al comprador original y a cualquier propietario posterior de los productos comprados para uso domstico dentro de EE. UU. Si el producto est en un rea donde no se encuentra disponible un Proveedor Autorizado del Servicio Tcnico de GE Appliances, usted ser responsable por el costo de un viaje o se podr requerir que traiga el producto a una ubicacin del Servicio Tcnico de GE Appliances autorizado para recibir el servicio. En Alaska, la garanta limitada excluye el costo de envo o visitas de servicio a su domicilio. Algunos estados no permiten la exclusin o limitacin de daos fortuitos o consecuentes. Esta garanta limitada le otorga derechos legales especficos, y usted tambin podra tener otros derechos que varan de estado a estado. Para conocer cules son sus derechos legales, consulte a la oficina de asuntos del consumidor local o estatal o al Fiscal de su estado.

Garante: GE Appliances, a Haier company Louisville, KY 40225

Garantas Extendidas: Adquiera una garanta extendida de GE Appliances y conozca los descuentos especiales que estn disponibles mientras su garanta an est vigente. Puede acceder a la misma a travs de Internet en cualquier momento en

GEAppliances.com/extended-warranty

o llamando al 800.626.2224 durante el horario comercial. Los Servicios para los GE Appliances an estarn disponibles cuando su garanta caduque.

18 49-2000733 Rev. 1

Busca Algo Ms? GE Appliances ofrece una variedad de accesorios para mejorar sus experiencias de coccin y mantenimiento! Para acceder a nmeros telefnicos e informacin de sitios Web, consulte la pgina de Soporte para el Consumidor. Estos y otros productos estn disponibles:

Accesorios

Piezas Marco de Acero Inoxidable Negro (30) Marco de Acero Inoxidable Negro (36)

Suministros de Limpieza Limpiadores de Acero Inoxidable CitriShine Limpiador de Electrodomsticos de Acero Inoxidable

A C

C ES

O R

IO S

49-2000733 Rev. 1 19

Notas

20 49-2000733 Rev. 1

Soporte para el Consumidor SO

PO R

TE P

A R

A EL

C O

N SU

M ID

O R

Sitio Web de GE Appliances Desea realizar una consulta o necesita ayuda con su electrodomstico? Intente a travs del Sitio Web de GE Appliances las 24 horas del da, cualquier da del ao! Usted tambin puede comprar ms electrodomsticos maravillosos de GE Appliances y aprovechar todos nuestros servicios de soporte a travs de Internet, diseados para su conveniencia. En EE.UU.: GEAppliances.com

Registre su Electrodomstico Registre su electrodomstico nuevo a travs de Internet, segn su conveniencia! Un registro puntual de su producto permitir una mejor comunicacin y un servicio ms puntual de acuerdo con los trminos de su garanta, en caso de surgir la necesidad. Tambin puede enviar una carta en la tarjeta de inscripcin preimpresa que se incluye con el material embalado. En EE.UU.: GEAppliances.com/register

Servicio Programado El servicio de reparacin de expertos de GE Appliances est a slo un paso de su puerta. Conctese a travs de Internet y programe su servicio a su conveniencia cualquier da del ao. En EE.UU.: GEAppliances.com/service o comunquese al 800.432.2737 durante el horario de atencin comercial.

Garantas Extendidas Adquiera una garanta extendida de GE Appliances y conozca los descuentos especiales que estn disponibles mientras su garanta an est vigente. La puede adquirir en cualquier momento a travs de Internet. Los servicios de GE Appliances an estarn all cuando su garanta caduque. En EE.UU.: GEAppliances.com/extended-warranty o comunquese al 800.626.2224 durante el horario de atencin comercial.

Conectividad Remota Para solicitar asistencia para la conectividad de red inalmbrica (para modelos con acceso remoto), visite nuestro sitio web en GEAppliances.com/connect o comunquese al 800.220.6899 en EE.UU.

Piezas y Accesorios Aquellos individuos calificados para realizar el servicio tcnico de sus propios electrodomsticos podrn solicitar el envo de piezas o accesorios directamente a sus hogares (se aceptan las tarjetas VISA, MasterCard y Discover). Ordene hoy a travs de Internet durante las 24 horas, todos los das. En EE.UU.: GEApplianceparts.com o de forma telefnica al 877.959.8688 durante el horario de atencin comercial. Las instrucciones que figuran en este manual cubren los procedimientos que sern realizados por cualquier usuario. Otros servicios tcnicos generalmente deben ser derivados a personal calificado del servicio. Se deber tener cuidado, ya que una reparacin indebida podr hacer que el funcionamiento no sea segu

Manualsnet FAQs

If you want to find out how the UVD6361DPBB GE works, you can view and download the GE UVD6361S UVD6361DPBB Vent System Installation Instructions on the Manualsnet website.

Yes, we have the Installation Instructions for GE UVD6361DPBB as well as other GE manuals. All you need to do is to use our search bar and find the user manual that you are looking for.

The Installation Instructions should include all the details that are needed to use a GE UVD6361DPBB. Full manuals and user guide PDFs can be downloaded from Manualsnet.com.

The best way to navigate the GE UVD6361S UVD6361DPBB Vent System Installation Instructions is by checking the Table of Contents at the top of the page where available. This allows you to navigate a manual by jumping to the section you are looking for.

This GE UVD6361S UVD6361DPBB Vent System Installation Instructions consists of sections like Table of Contents, to name a few. For easier navigation, use the Table of Contents in the upper left corner.

You can download GE UVD6361S UVD6361DPBB Vent System Installation Instructions free of charge simply by clicking the “download” button in the upper right corner of any manuals page. This feature allows you to download any manual in a couple of seconds and is generally in PDF format. You can also save a manual for later by adding it to your saved documents in the user profile.

To be able to print GE UVD6361S UVD6361DPBB Vent System Installation Instructions, simply download the document to your computer. Once downloaded, open the PDF file and print the GE UVD6361S UVD6361DPBB Vent System Installation Instructions as you would any other document. This can usually be achieved by clicking on “File” and then “Print” from the menu bar.