GE JX830 JX827SFSS Trim Kit Installation Instructions PDF

1 of 8
1 of 8

Summary of Content for GE JX830 JX827SFSS Trim Kit Installation Instructions PDF

Installation Microwave Oven Instructions Built-In Trim Kits

1

BEFORE YOU BEGIN Read these instructions completely and carefully.

IMPORTANT Save these instructions for local inspectors use.

IMPORTANT Observe all governing codes and ordinances. Note to Installer Be sure to leave these instructions with the Consumer. Note to Consumer Keep these instructions for future reference. Skill level Installation of this appliance requires basic mechanical and electrical skills. Completion time 1 to 3 hours

recommend that two people install this microwave oven.

of this kit.

WARNING

Questions? Call GE Answer Center at 800.626.2000 or Visit our Website at: GEAppliances.com

PARTS INCLUDED PART QUANTITY

Screw A 3 extra

4 mm x 16 mm 4 required

NOTE: from spending extra time locating a replacement in case

FOR YOUR SAFETY:

WARNING switch power off at service panel and lock the service disconnecting means to prevent power from being switched

JX827 and JX830

1 LOCATE AND INSTALL THE BASE PAN

CUTOUT DIMENSIONS

WARNING This trim kit uses air flow from the top, bottom and sides of the trim frame. Blocking the air flow can cause the microwave to function improperly and may cause damage to the microwave.

Allow a 1 clearance beyond the edge of the trim frame to provide proper air flow.

FOR INSTALLATION ABOVE A BUILT-IN OVEN:

2

Installation Instructions

Screw A

TOOLS YOU WILL NEED

Centerpunch or nail

Knife

Width

trim frame

1 overlap

Bottom of trim kit must be minimum of 36 from floor

Dimension Trim Kit

Cutout 27 30

16 1 16 1 1 16

Width 7 7 7 1 16

3 INSTALL THE MICROWAVE OVEN

care not to pinch the power cord. Be sure to keep the

2 INSTALL THE RAILS

A protective film has been applied to some microwave

microwave oven.

3

Installation Instructions

5 SECURE THE RAILS TO THE CABINET

into the cabinet

Screw A

4 CHECK LEVELING

Oven Bottom

6 INSTALL THE TRIM KIT FRAME A

oven.

B the trim kit into the cabinet.

CAUTION Start all screws before tightening any one screw. Do not overtighten screws since it can

cause misalignment of top/side strips.

4

Installation Instructions

Screw B

READ CAREFULLY. KEEP THESE INSTRUCTIONS.

7 REPLACE ANY LOOSE ITEMS A

the turntable and turntable support that was removed from inside the microwave oven.

B Keep these installation instructions and extra screws

the microwave oven.

C restore power at the service panel.

Instrucciones Kits de Horno Microondas con de Instalacin Terminaciones Incorporadas

1

ANTES DE COMENZAR Lea estas instrucciones en su totalidad y atentamente. IMPORTANTE Conserve estas instrucciones

para uso del inspector local. IMPORTANTE Cumpla con todos los cdigos y

ordenanzas gubernamentales. Nota para el Instalador Asegrese de que el Comprador conserve estas instrucciones. Nota para el Comprador Conserve estas instrucciones para referencia futura. Nivel de habilidad La instalacin de este electrodomstico requiere un nivel bsico de habilidades mecnicas y elctricas. Tiempo de instalacin entre 1 y 3 horas

del instalador.

instalacin inadecuada, la Garanta no cubrir las mismas.

horno.

seguridad personal, recomendamos que la instalacin del horno microondas sea realizada por dos personas.

ADVERTENCIA correctamente enchufado en un receptculo de 3 agujeros y 120V, de acuerdo con lo requerido por el Cdigo de

Preguntas? Llame a 800.GE.CARES (800.432.2737) o Visite nuestro sitio web en: GEAppliances.com

PIEZAS INCLUIDAS PIEZA CANTIDAD

Kit de 1 Terminaciones

Tornillo A de 11 requeridos 4 mm. x 10 mm. 3 adicionales

4 mm. x 16 mm 2 adicionales

NOTA: evitar que el tcnico necesite tiempo adicional para ubicar un tornillo de reemplazo durante la instalacin.

PARA SU SEGURIDAD:

ADVERTENCIA Antes de comenzar con la instalacin, apague el interruptor del panel del servicio y bloquee el suministro del servicio a fin de evitar que la corriente se active en forma accidental. Cuando el suministro del servicio no pueda ser bloqueado, ajuste de forma segura un dispositivo de advertencia visible, tal como una etiqueta, al panel del servicio.

JX827 and JX830

1 UBIQUE E INSTALE UNA OLLA DE LA BASE

frontal del horno microondas y centre la misma sobre

que la pestaa frontal quede contra la pared frontal

DIMENSIONES DE LA ABERTURA

ADVERTENCIA Este kit con terminacin usa el flujo de aire desde la parte superior, inferior o los costados de la estructura con terminacin. Bloquear el flujo de aire puede hacer que el microondas funcione de forma inadecuada y ocasionar daos sobre el mismo.

Deje un espacio de 1 ms all del extremo de la estructura con terminacin para brindar el flujo de aire apropiado.

PARA LA INSTALACIN SOBRE UN HORNO EMPOTRABLE:

equivalentes de 2 x 4 o 1 x 2 en todos los costados. La base deber poder soportar un mnimo de 100 libras.

2

Instrucciones de Instalacin

Tornillos A

HERRAMIENTAS QUE NECESITAR

Lpiz

Cuchillo

Cinta mtrica

Altura

Ancho

estructura con terminacin

Dimensin Kit de Terminaciones

Abertura 27 30

Altura 16 1 2 16 1 2 1 16

Ancho 26 29 24 1 16

3 INSTALE EL HORNO MICROONDAS

el ensamble del horno microondas al gabinete de forma cuidadosa, teniendo cuidado de que no haya pellizcos sobre el cable de corriente. Asegrese de mantener el ensamble centrado a medida que se vuelve a deslizar hacia las lengetas de los rieles a travs de las ranuras de la Olla

deberan ahora estar centrados de derecha a izquierda en la

2 INSTALACIN DE LOS RIELES todo lo que haya dentro del horno microondas, incluyendo

horno microondas.

3

Instrucciones de Instalacin

5 ASEGURE LOS RIELES AL GABINETE

que los agujeros de los tornillos estn alineados. Coloque 4

gabinete.

Tornillo A

4 CONTROL DE LA NIVELACIN Controle la nivelacin colocando un nivel en el frente y

necesario agregar cuas de madera debajo de la olla de la base para nivelar el frente del microondas con la parte trasera o un costado con el otro.

Guas

6 INSTALACIN DE LA ESTRUCTURA DEL KIT CON TERMINACIONES

A Terminaciones alrededor del horno.

B Asegure el Kit con Terminaciones colocando cuatro

gabinete.

PRECAUCIN Ubique todos los tornillos antes de comenzar a ajustar el primero. No ajuste en exceso los tornillos, ya que esto podr ocasionar desalineaciones de las tiras superiores/ laterales.

4

Instrucciones de Instalacin

Screw B

LEA DETENIDAMENTE. CONSERVE ESTAS INSTRUCCIONES.

7 REEMPLACE CUALQUIER TEM FLOJO A

y su soporte correspondiente, que fueron retirados del interior del horno microondas.

B Guarde estas instrucciones de inst

Manualsnet FAQs

If you want to find out how the JX827SFSS GE works, you can view and download the GE JX830 JX827SFSS Trim Kit Installation Instructions on the Manualsnet website.

Yes, we have the Installation Instructions for GE JX827SFSS as well as other GE manuals. All you need to do is to use our search bar and find the user manual that you are looking for.

The Installation Instructions should include all the details that are needed to use a GE JX827SFSS. Full manuals and user guide PDFs can be downloaded from Manualsnet.com.

The best way to navigate the GE JX830 JX827SFSS Trim Kit Installation Instructions is by checking the Table of Contents at the top of the page where available. This allows you to navigate a manual by jumping to the section you are looking for.

This GE JX830 JX827SFSS Trim Kit Installation Instructions consists of sections like Table of Contents, to name a few. For easier navigation, use the Table of Contents in the upper left corner.

You can download GE JX830 JX827SFSS Trim Kit Installation Instructions free of charge simply by clicking the “download” button in the upper right corner of any manuals page. This feature allows you to download any manual in a couple of seconds and is generally in PDF format. You can also save a manual for later by adding it to your saved documents in the user profile.

To be able to print GE JX830 JX827SFSS Trim Kit Installation Instructions, simply download the document to your computer. Once downloaded, open the PDF file and print the GE JX830 JX827SFSS Trim Kit Installation Instructions as you would any other document. This can usually be achieved by clicking on “File” and then “Print” from the menu bar.