GE RAK150VF2 Thermostat Installation Instructions PDF

1 of 32
1 of 32

Summary of Content for GE RAK150VF2 Thermostat Installation Instructions PDF

SAFETY INFORMATION ....................2 OVERVIEW ........................................3 INSTALLATION ................................ 4 WIRING DIAGRAMS ..........................8 CONFIGURATION MODE .................10 OPERATING FUNCTIONS ............... 13 TROUBLESHOOTING ....................... 15 WARRANTY ..................................... 16

TH ER

M O

ST A

T D

ig it

al INSTALLATION INSTRUCTIONS

RAK150VF2

31-5000604 Rev. 1 02-22 GEA

2

Specifications

WARNING FIRE AND SHOCK HAZARD Always turn off power at the main power supply

before installing, cleaning or removing the thermostat. Failure to do so could result in electrical shock hazard.

Do not use on voltages over 30 VAC. Higher voltages will damage the thermostat and could cause shock or fire hazard.

All wiring must conform to local and national electrical and building codes.

Use this thermostat only as described in this manual.

Electrical rating: 24 VAC (1830 VAC) 1 amp maximum per terminal 4 amp maximum total load Operating temperature range: 40F99F (4C37C) Temperature set range: 60F85F (15C29C) Accuracy: 1F ( 0.5C) System configurations: Factory Setting: 3-stage heat (heat pump low, heat

pump high, resistance heat), 2-stage cool (cool low, cool high), 2-speed fan

Alternate Setting: 2-stage heat (heat pump/resistance heat), 1-stage cool, 2-speed fan

Alternate Setting: 1-stage heat (resistance heat), 1-stage cool, 2-speed fan

Terminations: R, C, B, Y1, W, Y2, GL, GH Wiring: Maximum wiring length is 66ft (20 meters) for AWG18. Maximum wiring length is 60ft (18 meters) for AWG20

IMPORTANT SAFETY INFORMATION READ ALL INSTRUCTIONS BEFORE USING

NOTICE

3

THERMOSTAT BASE LAYOUT

R C B Y1 W Y2 GL GH

RESET CONFIG

THERMOSTAT CONTROLS

MODE FAN

INTRODUCTION OVERVIEW

Display

Up/Down Buttons

Display Up/Down Buttons Wiring

Channel

Mounting Hole

Fan

ModeMounting Hole

Configuration Button

Reset Button

4

INSTALLATION INSTRUCTIONS

PACKAGE CONTENTS/TOOLS REQUIRED: Package includes: Thermostat base Thermostat cover Wiring labels Screws Wall anchors

Tools needed:

Hammer Screwdriver Putty

WARNING ELECTRICAL SHOCK HAZARD Turn off power by unplugging the unit or by removing the fuse or switching the appropriate circuit breaker to the OFF position before removing the existing thermostat. Failure to do so could result in risk of electric shock.

5

TO REMOVE EXISTING THERMOSTAT 1. Turn off power to heating and cooling system by

removing the fuse or switching off the appropriate circuit breaker.

2. Remove cover of old thermostat. This should expose the wires.

3. Label the existing wires with the enclosed wire labels before removing wires.

4. After labeling wires, remove wires from wire terminals.

5. Remove existing thermostat base from wall. 6. Refer to the following section for instructions on

how to install this thermostat.

INSTALLATION INSTRUCTIONS

6

TO INSTALL THERMOSTAT IMPORTANT: Thermostat installation must conform to local and national building and electrical codes and ordinances. NOTE: Mount the thermostat about five feet above the floor. Do not mount the thermostat on an outside wall, in direct sunlight, behind a door or in an area affected by a vent or duct. 1. Turn off power to the heating and cooling system

by removing the fuse or switching off the appropriate circuit breaker.

2. Remove the cover by inserting and twisting a coin or screwdriver in the slots on the top of the thermostat.

3. Put thermostat base against the wall where you plan to mount it. Make sure wires will feed through the wire opening in the base of the thermostat.

4. With the base level, mark the placement of the mounting holes.

5. Set thermostat base and cover away from working area.

6. you have marked for mounting.

7. Use a hammer to tap supplied anchors in mounting holes.

8. Align thermostat base with mounting holes and feed the control wires through the wire opening.

INSTALLATION INSTRUCTIONS

7

TO INSTALL THERMOSTAT (cont.) 9. Seal hole for wires behind thermostat with non-

flammable insulation or putty, or use a wall plate obtainable from a local hardware or home building store.

10. Use supplied screws to mount thermostat base to wall.

11. Insert stripped, labeled wires in matching wire terminals by pressing on the corresponding terminal contact. See the Wiring Diagrams section of this manual.

NOTICE Make sure exposed portion of wires do not touch other wires. 12. Gently tug wire to be sure of proper connection.

Double check that each wire is connected to the proper terminal.

13. Replace cover on thermostat by snapping it in place.

14. Plug the unit in or turn on power to the system at the main service panel.

15. Test thermostat operation.

INSTALLATION INSTRUCTIONS

8

WIRING DIAGRAMS

Table 1: Terminals for eight wires. 3-stage heat/2- stage cool system

R C B Y1 W Y2 GL GH

24 V

AC H

O T

24 V

AC C

O M

M O

N

RE VE

RS IN

G V

AL VE

ST AG

E 1

CO M

PR ES

SO R

H EA

T- EL

EC TR

IC

ST AG

E 2

CO M

PR ES

SO R

IN D

O O

R FA

N -L

O W

IN D

O O

R FA

N -H

IG H

9

Table 2: Terminals for seven wires. 2-stage heat/1-stage cool system

WIRING DIAGRAMS

Table 3: Terminals for six wires. 1-stage heat/1- stage cool system

R C B Y1 W Y2 GL GH

24 V

AC H

O T

24 V

AC C

O M

M O

N

RE VE

RS IN

G V

AL VE

ST AG

E 1

CO M

PR ES

SO R

H EA

T- EL

EC TR

IC

IN D

O O

R FA

N -L

O W

IN D

O O

R FA

N -H

IG H

R C B Y1 W Y2 GL GH

24 V

AC H

O T

24 V

AC C

O M

M O

N

ST AG

E 1

CO M

PR ES

SO R

H EA

T- EL

EC TR

IC

IN D

O O

R FA

N -L

O W

IN D

O O

R FA

N -H

IG H

10

CONFIGURATION MODE The configuration mode is used to set the RAK150VF2 to match the heating/cooling system. The default setting of this thermostat is for 2-stage cooling with a 3-stage heat pump system. For an alternate configuration, see #7 in the Configuration Mode Settings below. To configure the RAK150VF2, perform the following steps: 1. Ensure thermostat is in OFF mode. 2. Remove the thermostats front cover. 3. To enter the configuration mode, hold CONFIG for ~ 2 seconds. 4. Once in the configuration mode, press the < or > button to

change settings within each screen. -Press the FAN (right)button to advance to the next screen. - Press the MODE (left)button to return to the previous screen.

NOTE: Hold CONFIG button for ~2 seconds to save changes and exit configuration menu. Configuration Mode Settings The setup screens for Configuration Mode are as follows: 1. Temperature Scale (F or C)Choose Fahrenheit or Celsius.

- Press the < or > button to select. - Press the FAN (right) button to advance to the

next screen. NOTE: Default factory setting is Fahrenheit.

2. Temperature DifferentialStage 1(19F) (.5-4.5C) Set the number of degrees between the setpoint temperature and the turn on temperature for first stage.

- Press the < or > button to set differential value.

- Press the FAN (right) button to advance to the next screen. Note: Default factory setting is 1F /.5C. 3. Temperature DifferentialStage 2 (19F) (.5-4.5C)

Set the number of degrees between when stage 1 turns on and stage 2 turns on.

- Press the < or > button to set differential value.

- Press the FAN (right) button to advance to the next screen. - Note: Default factory setting is 1F/.5C.

:

:

11

4. Temperature DifferentialStage 3 (19F) (.5-4.5C) Set the number of degrees between when stage 2 turns on and stage 3 turns on

- Press the < or > button to set differential value.

- Press the FAN (right) button to advance to the next screen. - Note: Default factory setting is 1F/.5C.

5. System - Select appropriate cooling/heating system based on model selection

- HP b2: two stage cooling / two stage (B type) heat pump with a backup 3rd stage of resistance heat. Use for AZ9V models.

- HP b1: single stage cooling / single stage (B type) heat pump with a backup 2nd stage of resistance heat. Use for AZ95H and AZ65H models.

- ELC: single stage cooling / single stage resistance heating. Use for AZ95E and AZ45E Models.

- Press the < or > button to change selection. - Press the FAN (right) button to advance to the next screen. - Note: Default factory setting is HP b2.

6. Minimum Cool Setpoint (60, 64, 66, 68, 70, 72, 74, 76F) (15, 17, 19, 20, 21, 22, 23, 24C) Adjust to control the minimum Cool set temperature allowed.

- Press the < or > button to select. - Press the FAN (right) button to advance to the next screen.

Note: Default factory setting is 60F/15C.

CONFIGURATION MODE

:

HEAT

12

7. Maximum Heat Setpoint (65, 70, 72, 74, 76, 78, 80, 85F) (18, 21, 22, 23, 24, 26, 27, 29C) Adjust to control the maximum Heat set temperature allowed.

- Press the < or > button to select. - Press the FAN (right) button to advance to the next screen.

Note: Default factory setting is 85F/29C. 8. Room Temperature Offset (+9F to 9F) (+5C to 5C)

Adjust to calibrate displayed room temperature to match actual room temperature.

- Press the < or > button to select. - Press the FAN (right) button to advance to the next screen.

Note: Default factory setting is 0F/0C. 9. Continuous Fan

This setting controls the availability of the continuous fan options available for selection by the thermostat user. Continuous fan options allow for the fan to be operated all the time if selected.

- Press the < or > button to change selection. Note: Default factory setting is ON (1). 1=ON, 0=OFF

CONFIGURATION MODE

FAN

13

OPERATING FUNCTIONS Off In this mode, the thermostat will not turn on the heating or

cooling devices (manual fan can operate if Continuous Fan mode is enabled).

Off is also used to access Configuration mode.

Heat In this mode, the

thermostat controls the heating system.

Press the < or > button to set the desired temperature.

Cool In this mode, the

thermostat controls the cooling system.

Press the < or > button to set the desired temperature.

HEAT

Room Temp

Heating Indicator

Heating Setpoint

COOL

Room Temp

Cooling Indicator

Cooling Setpoint

14

OPERATING FUNCTIONS Fan Fan operation is available in either low or high speed. Press the < or > button to select a fan option. Selection

will be locked in after 8 seconds. Auto options operate the fan only during a cooling or

heating cycle. Continuous (On) options operate the fan all the time

including while in OFF mode. These options can be disabled in the thermostat configuration (Config #9).

FAN AUTO

FAN AUTO

FAN

FAN

Auto, Low Speed:

Auto, High Speed:

Continuous, Low Speed:

Continuous, High Speed:

15

TROUBLESHOOTING TIPS

Problem Solution No Display Check for 24 VAC; display is blank

when 24 VAC is not present

System fan does not come on properly

Verify that wiring is correct.

All thermostat buttons are inoperative

Verify that 24 VAC is present; unit will not operate when 24 VAC is not present.

Thermostat turns on and off too frequently

Adjust temperature differential (see Configuration Mode - Setting Temperature Differential, Stage 1, Stage 2, and Stage 3 section).

Fan runs continuously

Check fan selection. If set to ON, fan will run.

Room temperature is not correct

Verify that wall hole is plugged with putty or insulation to prevent airflow from the wall cavity. Adjust Temperature Offset (see Configuration Mode - Room temperature offset section).

Compressor doesnt run or turn off immediately when changing function or setting

There is a 3 minute time delay and a 3 minute minimum run time for the compressor when it turns on/off.

Fan doesnt run or turn off immediately when changing function or setting

This is normal. On some models, the fan may have a minimum run time/off time delay.

Problem not listed above

Press the Reset button once to reset the thermostat microprocessor.

16

THERMOSTAT WARRANTY

For The Period Of: GE Appliances Will Replace: One Year Full Replacement of the thermostat which fails From the date of the due to a defect in materials or workmanship. original purchase For Warranty replacement, contact your distributor.

What GE Appliances Will Not Cover: Service trips to your location. Improper installation. If you have an installation problem, contact

your installer. You are responsible for providing adequate electrical connections to the product.

Failure of the product resulting from modifications to the product or due to unreasonable use, including failure to provide reasonable and necessary maintenance.

In commercial locations, labor necessary to move the unit, after it has been initially installed, to a location where it is accessible for service by an individual technician; or, if the instructions included in this manual have been disregarded.

Replacement of location fuses or the resetting of circuit breakers. Damage to the product caused by improper power supply voltage,

accident, fire, floods or acts of God. Incidental or consequential damage caused by possible defects with

this thermostat.

Staple your receipt here. Proof of the original purchase date is

needed to validate the warranty.

This warranty is extended to the original purchaser and any succeeding owner for products purchased for use within the USA and Canada. In Alaska, the warranty excludes the cost of shipping or service calls to your site.

Some states or provinces do not allow the exclusion or limitation of incidental or consequential damages. This warranty gives you specific legal rights, and you may also have other rights which vary from state to state or province to province. To know what your legal rights are, consult your local, state or provincial consumer affairs office or your states Attorney General.

EXCLUSION OF IMPLIED WARRANTIESYour sole and exclusive remedy is product exchange as provided in this Limited Warranty. Any implied warranties, including the implied warranties of merchantability or fitness for a particular purpose, are limited to one year or the shortest period allowed by law.

Warrantor: GE Appliances, a Haier company Louisville, KY 40225

RENSEIGNEMENTS IMPORTANTS CONCERNANT LA SCURIT .............2 VUE DENSEMBLE .............................3 INSTALLATION ................................ 4 SCHMAS DE CBLAGE ...................8 CONFIGURATION MODE .................10 FONCTIONS DUTILISATION ......... 13 CONSEILS DE DPANNAGE ........... 15 GARANTIE LIMITE ......................... 16

Instructions Dinstallation

RAK150VF2

31-5000604 Rev. 1 02-22 GEA

TH ER

M O

ST A

T N

um r

iq ue

2

Fiche technique

RENSEIGNEMENTS IMPORTANTS CONCERNANT LA SCURIT LISEZ TOUTES LES INSTRUCTIONS AVANT DUTILISER CET APPAREIL

AVERTISSEMENT RISQUE DINCENDIE ET DLECTROCUTION

Mettez toujours lalimentation lectrique hors tension depuis la source dalimentation lectrique principale avant dinstaller, de nettoyer ou de retirer le thermostat. Nutilisez pas des tensions suprieures 30 VAC. Des tensions plus leves endommageront le thermostat en plus de reprsenter un risque dlectrocution ou dincendie. Tout le cblage doit tre conforme aux Codes de llectricit et du btiment locaux et nationaux. Utilisez ce thermostat aux seules fins dcrites dans ce manuel.

Caractristiques lectriques : 24 VAC (1830 VAC) 1 ampre maximum par borne 4 ampres maximum charge totale Gamme des tempratures de fonctionnement : 40F99F (4C37C) Plage des rglages de temprature : 60F85F (15C29C) Prcision : 1F ( 0.5C) Configurations du systme : Rglage lusine : Chauffage deux tapes (thermopompe/

chauffage par rsistance); refroidissement une tape, ventilateur deux vitesses.

Rglage facultatif : Chauffage une tape (chauffage par rsistance), refroidissement une tape, ventilateur deux vitesses

Bornes : R, C, W, Y, GH, GL, B Cblage : Longueur de cblage maximale de 66 pi (20 mtres)

pour AWG18 Longueur de cblage maximale de 60 pi (18 mtres) pour AWG20

3

R C B Y1 W Y2 GL GH

RESET CONFIG

COMMANDE DU THERMOSTAT

MODE FAN

DISPOSITION DE LA BASE DU THERMOSTAT

PRSENTATION APERU

cran

Boutons flchs

cran Boutons flchs Chemin

de cblage

Trou de montageTrou de

montage

Bouton de configuration

Bouton de rinitialisation

Ventilateur

Mode

4

INSTRUCTIONS DINSTALLATION

WARNING RISQUE DLECTROCUTION Coupez lalimentation en dbranchant lappareil ou en retirant le fusible ou mettant le disjoncteur appropri la position OFF (hors tension) avant de retirer le thermostat. Lomission de procder ainsi peut occasionner un choc lectrique.

Contenu de lemballage Couvercle du thermostat Base du thermostat

Vis Ancrages muraux

Outils requis Perceuse et mche de 5 mm (3/16 po) Marteau Tournevis

5

INSTRUCTIONS DINSTALLATION

POUR RETIRER LE THERMOSTAT EXISTANT 1. Mettez le systme de chauffage et de climatisation

hors tension en retirant le fusible ou en dclenchant le disjoncteur appropri.

2. Retirez le couvercle du thermostat changer. Ceci devrait exposer les fils.

3. tiquetez les fils existants laide des tiquettes fournies avant denlever les fils.

4. Aprs avoir tiquet les fils, dbranchez les fils des cosses.

5. Retirez la base du thermostat existant du mur. 6. Consultez la section suivante pour des instructions

relatives linstallation du thermostat.

6

INSTALLATION DU THERMOSTAT IMPORTANT: Linstallation de ce thermostat doit tre conforme tous les codes et tous les rglements des Codes du btiment et de llectricit locaux et nationaux. REMARQUE: Montez le thermostat une hauteur denviron 1,5 m (5 pi) au-dessus du plancher. Ne montez pas le thermostat sur un mur extrieur, directement expos aux rayons de soleil, derrire une porte ou un endroit o une bouche ou un conduit daration pourrait nuire au fonctionnement. 1. Mettez le systme de chauffage et de climatisation

hors tension en retirant le fusible ou en dclenchant le disjoncteur appropri.

2. Retirez le couvercle en insrant et tournant une pice de monnaie ou un tournevis dans les fentes dans le haut du thermostat.

3. Apposez la base du thermostat contre le mur o il doit tre install. Assurez-vous que les fils passeront par louverture de fil situe sur la base du thermostat.

4. Utilisez un niveau pour niveler et marquer lemplacement des trous de montage.

5. loignez la base et le couvercle du thermostat du lieu de travail.

6. Utilisez une mche de 5 mm (3/16 po) pour percer des avant-trous aux emplacements marqus pour les vis bois.

7. Utilisez un marteau pour rentrer les ancrages fournis dans les trous de montage.

8. Alignez la base du thermostat sur les trous de montage et faites passer les fils de commande travers le trou des fils.

INSTRUCTIONS DINSTALLATION

7

INSTALLATION DU THERMOSTAT (cont.) 9. Scellez le trou des fils derrire le thermostat laide dun

isolant ou dun mastic non inflammables, ou utilisez une plaque murale obtenue auprs dune quincaillerie.

10. Utilisez les vis fournies pour monter la base du thermostat sur le mur.

11. Insrez les fils dnuds et tiquets dans les bornes correspondantes en pressant le contact des bornes. Voyez la section Schmas de cblage de ce manuel.

NOTICE Assurez-vous que la partie expose des fils ne touche pas aux autres fils. 12. Tirez dlicatement chaque fil pour vous assurer quil

est bien raccord. Assurez-vous que chaque fil est raccord au conducteur lectrique appropri.

13. Replacez le couvercle sur le thermostat en lenclenchant en place.

14. Branchez lunit ou mettez le systme sous tension au niveau du panneau de service principal.

15. Testez le fonctionnement du thermostat.

INSTRUCTIONS DINSTALLATION

8

SCHMAS DE CBLAGE

Tableau 1: Bornes pour huit fils. Systme de chauffage 3 tapes/refroidissement 2 tapes

R C B Y1 W Y2 GL GH

24 V

AC H

O T

24 V

AC C

O M

M O

N

RE VE

RS IN

G V

AL VE

ST AG

E 1

CO M

PR ES

SO R

H EA

T- EL

EC TR

IC

ST AG

E 2

CO M

PR ES

SO R

IN D

O O

R FA

N -L

O W

IN D

O O

R FA

N -H

IG H

VE N

TI LA

TE U

R IN

T R

IE U

R B

AS

VE N

TI LA

TE U

R IN

T R

IE U

R H

AU T

N EU

TR E

24 V

C A

C H

AU D

2 4

VC A

C O

M PR

ES SE

U R

1

TA

PE

C O

M PR

ES SE

U R

2

TA

PE

R O

BI N

ET IN

VE R

SE U

R

C H

AU FF

AG E

L EC

TR IQ

U E

9

Tableau 2: Bornes pour sept fils. Systme de chauffage 2 tapes/refroidissement 1 tape

SCHMAS DE CBLAGE

Tableau 3: Bornes pour six fils. Systme de chauffage 1 tape/refroidissement 1 tape

R C B Y1 W Y2 GL GH

24 V

AC H

O T

24 V

AC C

O M

M O

N

RE VE

RS IN

G V

AL VE

ST AG

E 1

CO M

PR ES

SO R

H EA

T- EL

EC TR

IC

IN D

O O

R FA

N -L

O W

IN D

O O

R FA

N -H

IG H

R C B Y1 W Y2 GL GH

24 V

AC H

O T

24 V

AC C

O M

M O

N

ST AG

E 1

CO M

PR ES

SO R

H EA

T- EL

EC TR

IC

IN D

O O

R FA

N -L

O W

IN D

O O

R FA

N -H

IG H

VE N

TI LA

TE U

R IN

T R

IE U

R B

AS

VE N

TI LA

TE U

R IN

T R

IE U

R H

AU T

VE N

TI LA

TE U

R IN

T R

IE U

R B

AS

VE N

TI LA

TE U

R IN

T R

IE U

R H

AU T

N EU

TR E

24 V

C A

N EU

TR E

24 V

C A

C H

AU D

2 4

VC A

C H

AU D

2 4

VC A

C O

M PR

ES SE

U R

1

TA

PE C

O M

PR ES

SE U

R

1

TA PE

R O

BI N

ET IN

VE R

SE U

R

C H

AU FF

AG E

L EC

TR IQ

U E

C H

AU FF

AG E

L EC

TR IQ

U E

10

MODE DE CONFIGURATION Le mode de configuration est utilis pour rgler le RAK150VF2 afin quil corresponde au systme de chauffage-refroidissement. La configuration par dfaut de ce thermostat correspond un systme thermopompe 2 tapes de refroidissement et 3 tapes de chauffage. Pour une configuration diffrente, voyez ltape 7 de la rubrique Rglages du mode de configuration ci-dessous. Pour configurer le RAK150VF2, excutez les tapes suivantes : 1. Assurez-vous que le thermostat est la position OFF. 2. Retirez le couvercle frontal du thermostat. 3. Pour entrer dans le mode de configuration, pressez CONFIG

durant environ 2 secondes. 4. Une fois dans le mode de configuration, appuyez sur le bouton < ou > pour modifier les paramtres dans chaque cran. - Appuyez sur le bouton FAN pour passer lcran suivant. - Appuyez sur le bouton MODE pour revenir lcran

prcdent. REMARQUE: Pressez CONFIG durant environ 2 secondes pour sauvegarder les modifications et quitter le menu de configuration. Rglages du mode de configuration Les fentres de rglage du mode de configuration sont les suivantes : 1. chelle de tempratures (F ou C) Choisir

Fahrenheit ou Celsius. - Pressez le bouton < ou > pour slectionner. - Pressez le bouton Right pour avancer la fentre suivante.

REMARQUE : Le rglage par dfaut est Fahrenheit. 2. cart de temprature tape 1 (19F) (.5-4.5C)

- Rglez le nombre de degrs entre la temprature du rglage et la temprature au dmarrage pour la premire tape.

- Pressez le bouton < ou > pour rgler la valeur de lcart de temprature.

- Pressez le bouton FAN pour avancer la fentre suivante. Remarque : Le rglage par dfaut est 1F /.5C pour chaque tape. 3. cart de temprature tape 2 (19F) (.5-4.5C)

thermopompe (HPb) seulement - Rglez le nombre de degrs entre le dmarrage

de ltape 1 et le dmarrage de ltape 2. - Pressez le bouton < ou > pour rgler la

valeur de lcart de temprature. - Pressez le bouton RIGHT pour avancer la fentre suivante.

Remarque : Le rglage par dfaut de lusine est 1F/.5C.

:

:

11

4. cart de temprature tape 3 (19F) (.5-4.5C) Rglez le nombre de degrs entre le moment o ltape 2 sactive et celui o ltape 3 sactive

- Pressez le bouton < ou > pour rgler la valeur diffrentielle.

- Pressez le bouton FAN pour avancer la fentre suivante.

Remarque : Le rglage par dfaut est 1F/.5C pour chaque tape. 5. Systme Slectionnez le systme de chauffage-

refroidissement appropri selon le modle slectionn. - HP b2 : Thermopompe refroidissement 2 tapes et chauffage 2 tapes (type B) avec chauffage dappoint lectrique de troisime tape utiliser avec les modles AZ9V. - HP b1 : Thermopompe refroidissement 1 tape et chauffage 1 tape (type B) avec chauffage dappoint lectrique de deuxime tape. utiliser avec les modles AZ95H et AZ65H. - ELC : Refroidissement 1 tape et chauffage lectrique 1 tape. utiliser avec les modles AZ95E et AZ45E.

- Pressez le bouton < ou > pour rgler la valeur de lcart de temprature.

- Pressez le bouton FAN pour avancer la fentre suivante. - Remarque : Le rglage par dfaut est HP b2 pour chaque

tape. 6. Rglage de refroidissement minimal (60, 64, 66, 68, 70, 72,

74, 76F) (15, 17, 19, 20, 21, 22, 23, 24C) - Ajustez pour contrler la temprature de

refroidissement minimale permise. - Pressez le bouton < ou > pour rgler la

valeur de lcart de temprature. - Pressez le bouton FAN pour avancer la fentre suivante.

Remarque : Le rglage par dfaut est 60F/15C pour chaque tape.

MODE DE CONFIGURATION

:

HEAT

12

7. Rglage de chauffage maximal (65, 70, 72, 74, 76, 78, 80, 85F) (18, 21, 22, 23, 24, 26, 27, 29C)

- Ajustez pour contrler la temprature de chauffage maximale permise.

- Pressez le bouton < ou > pour rgler la valeur de lcart de temprature.

- Pressez le bouton FAN pour avancer la fentre suivante. Remarque : Le rglage par dfaut est 85F/29C pour chaque tape. 8. cart la temprature ambiante (+9F to 9F) (+5C to

5C) - Ajustez pour calibrer la temprature ambiante

affiche afin de correspondre la temprature ambiante relle.

- Pressez le bouton < ou > pour rgler la valeur de lcart de temprature.

- Pressez le bouton FAN pour avancer la fentre suivante. Remarque : Le rglage par dfaut est 0F/0C pour chaque tape. 9. Fonctionnement en continu du ventilateur

Ce rglage contrle la disponibilit des options de fonctionnement en continu du ventilateur quil est possible de slectionner par lutilisateur du thermostat.

- Pressez le bouton < ou > pour changer la slection. Remarque : Le rglage par dfaut de lusine est ON (marche)(1). 1=ON, 0=OFF

MODE DE CONFIGURATION

FAN

13

FONCTIONS DUTILISATION OFF (arrt) Dans ce mode, le thermostat nallumera pas les

dispositifs de chauffage ou de refroidissement (le ventilateur manuel peut fonctionner).

Le mode OFF sert aussi accder aux mode Configuration.

Heat (chauffage) Dans ce mode, le

thermostat contrle le systme de chauffage.

Appuyez sur le bouton

< oU > pour rgler la temprature souhaite.

Cool (refroidissement) Dans ce mode, le

thermostat contrle le systme de refroidissement.

Appuyez sur le bouton < oU > pour rgler la temprature souhaite.

HEAT

Temprature ambiante

Voyant de

Rglage Temp.

COOL

Temprature ambiante

Voyant de refroidissement

Rglage Temp. refroidissement

14

FONCTIONS DUTILISATION Le ventilateur Le ventilateur peut fonctionner en basse ou haute vitesse. Appuyez sur le bouton < ou > pour slectionner une

option de ventilateur. La slection sera verrouille aprs 8 secondes.

Les options Auto activent le ventilateur seulement dans le cycle de refroidissement ou de chauffage.

Les options de fonctionnement en continu (On) activent le ventilateur en permanence y compris en mode OFF . Ces options peuvent tre dsactives dans le mode de configuration du thermostat (tape 9).

Auto, basse vitesse :

Auto, haute vitesse :

En continu, basse vitesse :

En continu, haute vitesse :

FAN AUTO

FAN AUTO

FAN

FAN

15

ESSAI DU THERMOSTAT

Problme Solution Assurez-vous que la tension est de

pas sans cette tension.

Le systme de ventilation ne se met pas en marche correctement

Aucun bouton du thermostat ne fonctionne.

Assurez-vous que la tension est de 24 VAC; lappareil ne fonctionnera pas sans cette tension.

Le thermostat sallume et steint trop frquemment

Ajustez lcart de temprature (voir

cart de temprature, tape 1 et tape 2).

Le ventilateur ne sarrte pas. du ventilateur. Sil est la position

ON, le ventilateur va fonctionner.

La temprature de la pice est errone. est bouch avec du mastic ou un

de la cavit murale. Ajustez lcart de temprature (voir la section

temprature ambiante)

Le compresseur ne fonctionne pas ou steint immdiatement aprs une

ou de rglage.

Il y a une temporisation de trois (3) minutes et un temps de fonctionnement minimum de trois (3) minutes pour le compresseur lorsquil se met en marche et sarrte

Le ventilateur ne fonctionne pas ou steint immdiatement aprs une

ou de rglage.

Pressez le bouton Reset (rinitialisation) une fois pour rinitialiser le microprocesseur du thermostat.

16

GARANTIE LIMITE DU THERMOSTAT

Ce que GE Appliances ne couvre pas : Frais de dplacement pour rparation vers votre emplacement. Une installation mal effectue. Si vous avez un problme dinstallation, communiquez avec votre installateur. Vous tes responsable deffectuer correctement les raccords lectriques de votre produit.

Une dfectuosit du produit cause par des modifications au produit ou par son usage draisonnable, y compris le dfaut deffectuer des entretiens raisonnables et ncessaires.

Dans les locaux commerciaux, la main-duvre ncessaire pour dplacer lappareil, aprs son installation initiale, un endroit o il est accessible pour lentretien par un technicien individuel; ou, si les instructions contenues dans ce manuel nont pas t respectes.

Le remplacement des fusibles ou lenclenchement des disjoncteurs du site. Les bris du produit causs pour une tension dalimentation lectrique inadquate, un accident, un incendie, les inondations et les cas de force majeure.

Les dommages accessoires ou immatriels causs par des probabilits de dfectuosits avec ce thermostat.

Brochez votre reu ici. Une preuve de la date dachat originale est ncessaire pour valider la garantie.

Cette garantie limite est consentie son premier acheteur et tout propritaire subsquent pour les produits achets pour utilisation aux tats-Unis et au Canada. En Alaska, la garantie limite exclut les frais dexpdition ou les appels de service vers votre site. Certains tats ou provinces nautorisent pas lexclusion ou la limitation des dommages accessoires ou immatriels. Cette garantie limite vous donne des droits lgaux spcifiques, et vous pouvez galement avoir dautres droits qui varient dun tat ou dune province lautre. Pour connatre vos droits lgaux, consultez votre bureau dinformation aux consommateurs local, provincial ou dtat ou le procureur gnral de votre tat.

Garant : GE Appliances, Louisville, KY 40225

EXCLUSION DES GARANTIES IMPLICITES - Votre seul et unique recours est lchange du produit comme prvu dans cette garantie limite. Toute garantie implicite, y compris les garanties implicites de qualit marchande ou dadaptation

Manualsnet FAQs

If you want to find out how the RAK150VF2 GE works, you can view and download the GE RAK150VF2 Thermostat Installation Instructions on the Manualsnet website.

Yes, we have the Installation Instructions for GE RAK150VF2 as well as other GE manuals. All you need to do is to use our search bar and find the user manual that you are looking for.

The Installation Instructions should include all the details that are needed to use a GE RAK150VF2. Full manuals and user guide PDFs can be downloaded from Manualsnet.com.

The best way to navigate the GE RAK150VF2 Thermostat Installation Instructions is by checking the Table of Contents at the top of the page where available. This allows you to navigate a manual by jumping to the section you are looking for.

This GE RAK150VF2 Thermostat Installation Instructions consists of sections like Table of Contents, to name a few. For easier navigation, use the Table of Contents in the upper left corner.

You can download GE RAK150VF2 Thermostat Installation Instructions free of charge simply by clicking the “download” button in the upper right corner of any manuals page. This feature allows you to download any manual in a couple of seconds and is generally in PDF format. You can also save a manual for later by adding it to your saved documents in the user profile.

To be able to print GE RAK150VF2 Thermostat Installation Instructions, simply download the document to your computer. Once downloaded, open the PDF file and print the GE RAK150VF2 Thermostat Installation Instructions as you would any other document. This can usually be achieved by clicking on “File” and then “Print” from the menu bar.