GE RAK204 RAK204SW Switch Kit Installation Instructions PDF

1 of 8
1 of 8

Summary of Content for GE RAK204 RAK204SW Switch Kit Installation Instructions PDF

31-5000558 Rev. 0 10-20 GEA

Tools Needed 5/16 nut driver Pliers Slotted screwdriver

Important Notes This unit must be properly grounded.

Read this instruction before installing the sub-base to the molded or metal case.

The sub-base should be assembled to the case before securing the case in the wall. CAUTION Electrical power must be disconnected

before installing the sub-base.

Electrical Requirements :

1. Electrical wiring may enter the sub-base through any of the knockout holes provided in the sub-base bottom or rear. Use appropriate protection around the opening to ensure the wiring will not become cut or chafed.

2. Refer to the unit nameplate for branch circuit requirements.

3. All wiring should be done in accordance with the local electrical codes and regulations.

4. Not approved for aluminum wire application.

5. If electrical wiring is placed in or against the sub-base enclosure, the sub-base must be grounded. Use the installed ground screw to connect the ground wire eyelet from the kit to the rear of the sub-base. See step 4.

Parts included in bag with Sub- Base Switch Kit

Installation Instructions for your new

RAK204 Sub-Base Switch KitBefore you begin - Read these instructions completely

and carefully. IMPORTANT OBSERVE ALL GOVERNING CODES AND ORDINANCES. Note to Installer Be sure to leave these instructions with the Consumer. Note to Consumer Keep these instructions with your Owners Manual for future reference.

RAK204SW kit compatible with the following Sub base models

Kit Number Description

RAK204E15C 265 V 15 A

RAK204E20C 265 V 20 A

RAK204E30C 265 V 30 A

RAK204D15C 230/208 V 15 A

RAK204D20C 230/208 V 20 A

RAK204D30C 230/208 V 30 A

5/16 Nut

Sub-Base Switch

Wire Nuts (4)

2

Installation Instructions

STEP 1

Disconnect all power to the unit. Remove the three panels from the front of the sub base by removing the 5/16 screws. Retain the middle and right hand side panels and all of the screws.

Screws

STEP 2

Place the Sub base switch in the OFF position. Hold the sub base switch assembly and thread the wires into the left side opening and across toward the right side

of the sub base. The wires labeled To Power Source will continue until the far right section of the sub base. The wires labeled To Receptacle Outlet and Ground wire will continue to the middle section.

OFF

Ground Wire

To Receptacle Outlet

To Power Source

3

Installation Instructions

STEP 3

Secure the Left side cover with switch assembly to the Sub Base using the retained screws.

STEP 4

To attach the ground wire from the Sub Base Switch, place the ring terminal onto the existing ground screw and secure with the provided 5/16 lock nut.

Existing ground wire

Green ground screw (type C)

Ground Wire

To Receptacle Outlet To Power Source

4

Installation Instructions

A Quality Product of GE Appliances

STEP 5

WIRING DIAGRAM

Use wire nuts (provided) to connect the Sub base switch to the electrical sub base wiring. See diagram above.

STEP 6 Reattach the middle and right side face plates using the screws saved from step 1.

STEP 7 Verify wiring and restore power to unit.

OFF

To Receptacle To Power Source

To Receptacle To Power Source

L2

L1 BLK

BLKBLK

RED OR WHITE

RED OR WHITE

RED OR WHITE

GRN/YEL GROUND

Trousse RAK204SW compatible avec les modles de socle suivants

31-5000558 Rev. 0 10-20 GEA

Outil ncessaire Tournevis douille 5/16 po Pince Tournevis pour crou fente

Remarques importantes Cet appareil doit tre correctement mis la terre. Lisez cette instruction avant dinstaller le socle sur la

gaine moule ou mtallique. Le socle doit tre mont sur la gaine avant de fixer la gaine dans le mur.

ATTENTION Lalimentation lectrique doit tre dbranche avant dinstaller le socle. EXIGENCES LECTRIQUES : 1. Le cblage lectrique doit pntrer dans le socle

travers une des dbouchures prsentes dans le bas ou larrire du socle. Utilisez une protection approprie autour de louverture pour vous assurer que le cblage ne sera pas coup ou endommag par frottement.

2. Reportez-vous la plaque signaltique de lappareil pour les exigences relatives au circuit de drivation.

3. Tout le cblage lectrique doit tre ralis conformment aux codes et rglements locaux.

4. Le cblage en aluminium nest pas approuv. 5. Si le cblage lectrique est positionn dans ou contre le

botier de socle, le socle doit tre mis la terre. Utilisez la vis de mise la terre pour connecter lillet de fil de mise la terre fourni dans la trousse larrire du socle. Consultez ltape 4.

Pices incluses dans le sac avec le socle

Instructions dinstallation pour votre nouveau socle

RAK204SW Trousse dinterrupteur de socle

Avant de commencer Lisez ces instructions attentivement et en totalit. IMPORTANT OBSERVEZ TOUS LES CODES ET RGLEMENTS EN VIGUEUR. Remarque linstallateur Assurez-vous de remettre ces instructions au consommateur. Remarque au consommateur Conservez ces instructions avec le manuel dutilisation pour consultation ultrieure.

Numro de trousse

RAK204E15C 265 V 15 A

RAK204E20C 265 V 20 A

RAK204E30C 265 V 30 A

RAK204D15C 230/208 V 15 A

RAK204D20C 230/208 V 20 A

RAK204D30C 230/208 V 30 A

crou de 5/16 po

Interrupteur de socle

Capuchons de connexion (4)

2

Instructions dinstallation

TAPE 1

Dbranchez toute source dalimentation de lappareil. Retirez les trois panneaux de lavant du socle en retirant les vis de 5/16 po. Conservez les panneaux central et droit, et toutes les vis.

Vis

TAPE 2

Mettez linterrupteur de socle la position OFF . Tenez linterrupteur de socle et passez les fils dans louverture du ct gauche et travers le ct droit du socle. Les fils identifis To Power Source ( la source dalimentation) continueront jusqu la section compltement

droite du socle. Les fils identifis To Receptacle Outlet ( la prise) et Ground wire (Fil de mise la terre) continueront

jusqu la section centrale.

OFF

Fil de mise la terre la prise

la source dalimentation

3

Instructions dinstallation

TAPE 3

Fixez le couvercle gauche avec linterrupteur sur le socle laide des vis conserves.

TAPE 4

Pour fixer le fil de mise la terre de linterrupteur de socle, placez la cosse anneau sur la vis de mise la terre existante et fixez le tout avec lcrou de blocage de 5/16 po fourni.

Fil de mise la terre existant

Vis de mise la terre verte (type C)

Fil de mise la terre

la prise la source dalimentation

4

Instructions dinstallation

Un produit de qualit de GE Appliances

TAPE 5

SCHMA DE PRINCIPE

Utilisez des capuchons de connexion (fournis) pour raccorder linterrupteur de socle au cblage du socle lectrique. Consultez le schma ci-dessus.

TAPE 6 Fixez de nouveau les plaques frontales centrale et droite laide des vis conserves ltape 1.

TAPE 7 Vrifiez le cbl

Manualsnet FAQs

If you want to find out how the RAK204 GE works, you can view and download the GE RAK204 RAK204SW Switch Kit Installation Instructions on the Manualsnet website.

Yes, we have the Installation Instructions for GE RAK204 as well as other GE manuals. All you need to do is to use our search bar and find the user manual that you are looking for.

The Installation Instructions should include all the details that are needed to use a GE RAK204. Full manuals and user guide PDFs can be downloaded from Manualsnet.com.

The best way to navigate the GE RAK204 RAK204SW Switch Kit Installation Instructions is by checking the Table of Contents at the top of the page where available. This allows you to navigate a manual by jumping to the section you are looking for.

This GE RAK204 RAK204SW Switch Kit Installation Instructions consists of sections like Table of Contents, to name a few. For easier navigation, use the Table of Contents in the upper left corner.

You can download GE RAK204 RAK204SW Switch Kit Installation Instructions free of charge simply by clicking the “download” button in the upper right corner of any manuals page. This feature allows you to download any manual in a couple of seconds and is generally in PDF format. You can also save a manual for later by adding it to your saved documents in the user profile.

To be able to print GE RAK204 RAK204SW Switch Kit Installation Instructions, simply download the document to your computer. Once downloaded, open the PDF file and print the GE RAK204 RAK204SW Switch Kit Installation Instructions as you would any other document. This can usually be achieved by clicking on “File” and then “Print” from the menu bar.