GE JB256 JB256DMBB Range Installation Instructions PDF

1 of 2
1 of 2

Summary of Content for GE JB256 JB256DMBB Range Installation Instructions PDF

BEFORE YOU BEGIN Read these instructions completely and carefully.

IMPORTANT Save these instructions for local inspectors use.

IMPORTANT Observe all governing codes and ordinances.

Note to Installer Be sure to leave these instructions with consumer.

Note to consumer Keep these instructions for future reference.

Skill level Installation of this appliance requires a qualified installer or electrician.

Proper installation is the responsibility of the installer.

Product failure due to improper installation is not covered under warranty.

FOR YOUR SAFETY:

If you did not receive an anti-tip bracket with your purchase, call 1.800.626.8774 to receive one at no cost. (In Canada, call 1.800.561.3344.) For installation instructions of the bracket, visit: GEAppliances.com. (In Canada, GEAppliances.ca.)

Installation Instructions Electric Slide-In Ranges

MATERIALS YOU MAY NEED TOOLS YOU WILL NEED

(UL Listed 40 AMP) 4-Wire Cord 4 long OR

3-Wire Cord 4 long

Squeeze Connector (For Conduit

Installations Only)

1 REMOVE PACKAGING MATERIALS: Failure to remove packaging materials could result in damage to the appliance. Remove all packing parts from oven, racks, heating elements and drawer. Also, remove protective film and labels on the outer door, cooktop and control panel.

Consider recycling options for your appliance packaging material.

Drill with 1/8 Bit Safety Glasses Adjustable Wrench Level

Tin Snips Tape Measure Pliers 1/4 Nut Driver

2 PREPARE THE OPENING (FOR INDOOR USE ONLY) See illustrations for all rough-in and spacing dimensions. The range may be placed with 0 clearance (flush) at the back wall and side walls of the cabinet.

NOTE: Use a 4 power cord to prevent interference with the storage drawer. Power cords 412 to 6 long may have to be dressed to allow for proper drawer closing.

MINIMUM DIMENSIONS BETWEEN COOKTOP, WALLS AND ABOVE THE COOKTOP: A. Make sure the wall covering, countertop, flooring and

cabinets around the range can withstand the heat (up to 200F) generated by the range. 0 to cabinets below cooktop and at the range back.

B. Allow 30 minimum clearance between surface units and bottom of unprotected wood or metal cabinet, or allow a 24 minimum when bottom of wood or metal cabinet is protected by no less than 1/4 thick flame retardant millboard covered with not less than No. 28 MSG sheet metal, (.015), .015 thick stainless steel, .024 aluminum or .020 copper.

C. This appliance has been approved for 0 spacing to adjacent surfaces above the cooktop. However, a 6 minimum spacing to surfaces less than 15 above the cooktop and adjacent cabinet is recommended to reduce exposure to steam, grease splatter and heat.

To reduce the risk of burns or fire when reaching over hot surface elements, cabinet storage space above the cooktop should be avoided. If cabinet storage space is to be provided above the cooktop, the risk can be reduced by installing a range hood that projects at least 5 beyond the front of the cabinets. Cabinets installed above the cooktop must be no deeper than 16.

3 ELECTRICAL REQUIREMENTS WARNING

This appliance must be properly grounded.

WARNING All new constructions, mobile homes, recreational vehicles and installations

where local codes do not allow grounding through neutral, require a 4-conductor UL-listed range cord.

WARNING To prevent fire or shock, do not use an extension cord with this appliance.

WARNING To prevent shock, remove house fuse or open circuit breaker before

beginning installation.

We recommend you have the electrical wiring and hookup of your range connected by a qualified electrician. After installation, have the electrician show you how to disconnect power from the range. You must use a single-phase, 120/208 VAC or 120/240 VAC, 60 hertz electrical system. If you connect to aluminum wiring, properly installed connectors approved for use with aluminum wiring must be used.

Effective January 1, 1996, the National Electrical Code requires that new construction (not existing) utilize a 4-conductor connection to an electric range. When installing an electric range in new construction, mobile home, recreational vehicle, or an area where local codes prohibit grounding through the neutral conductor, refer to the section on four-conductor branch circuit connections.

Check with your local utilities for electrical codes which apply in your area. Failure to wire your oven according to governing codes could result in a hazardous condition. If there are no local codes, your oven must be wired and fused to meet the National Electrical Code, NFPA No. 70 latest edition, available from the National Fire Protection Association.

This appliance must be supplied with the proper voltage and frequency, and connected to an individual, properly grounded, 40 amp (minimum) branch circuit protected by a circuit breaker or time-delay fuse. Use only a 3-conductor or a 4-conductor UL-listed range cord. These cords may be provided with ring terminals on wire and a strain relief device.

A range cord rated at 40 amps with 125/250 minimum volt range is required. A 50 amp range cord is not recommended but if used, it should be marked for use with nominal 138 diameter connection openings. Care should be taken to center the cable and strain relief within the knockout hole to keep the edge from damaging the cable.

The rating plate is located on the oven frame or on the side of the drawer frame. NOTE: Use of automatic, wireless or wired external switches that shut off power to the appliances, are not recommended for this product.

Rating plate

SINGLE OVEN

4 POWER CORD AND CONDUIT INSTALLATION A Remove wire cover (on the back of range) by removing screws using a 1/4 nut driver. You

can access the terminal block by either removing a terminal block cover (on some models) or the wire cover. Do not discard these screws.

B For power cord and 1 conduit only, remove the knockout ring (138) located on bracket directly below the terminal block. To remove the knockout, use a pair of pliers to bend the knockout ring away from the bracket and twist until ring is removed.

D For 3/4 conduit installations only, purchase a squeeze connector matching the diameter of your conduit and assemble it in the hole. Insert the conduit through the squeeze connector and tighten. Allow enough slack to easily attach the wires to the terminal block. NOTE: Do not install the conduit without a squeeze connector. The squeeze connector MUST be installed before reinstalling the rear terminal block.

Knockout ring in bracket

Knockout ring removed

Terminal block (appearance may vary)

C For power cord installations only (see the next step if using conduit), assemble the strain relief in the hole. Insert the power cord through the strain relief and tighten. Allow enough slack to easily attach the cord terminals to the terminal block. If tabs are present at the end of the winged strain relief, they can be removed for better fit.

NOTE: Do not install the power cord without a strain relief. The strain relief bracket MUST be installed before reinstalling the rear range wiring cover.

Power cord

Strain relief

Terminal block

Bracket

Squeeze connector

Terminal block

Conduit Bracket

Proceed to step 6 or 7.

5 3-WIRE INSTALLATION (GROUND IS THROUGH THE NEUTRAL WIRE)

WARNING Shock Hazard

The neutral wire and ground strap must be connected as shown below for the range to be properly grounded. Do not remove the ground strap. Failure follow this instruction may result in potential shock hazard.

WARNING Fire hazard

Terminal block screws must be securely tightened. Failure to do so may result in potential fire hazard.

FOR POWER CORD INSTALLATION A. Remove the 3 lower screws from the terminal block. Do not loosen the upper screws. B. Do not cut or remove the ground strap. C. Insert the 3 screws through each power cord

terminal ring and back into the terminal block. Be certain the white wire is in the center. Securely tighten each screw (35 to 50 in-lbs.)

FOR CONDUIT INSTALLATION A. Loosen the 3 lower screws on the terminal block. Do

not loosen the upper screws. B. Do not cut or remove the ground strap. C. Insert the bare wire tip (insulation stripped 5/8) into the

bottom terminal block openings. Be certain the white wire is in the center. On certain models, the wire must be inserted through an opening in the ground strap. Securely tighten each screw onto each wire (35 to 50 in-lbs.).

D. Reinstall terminal block cover. NOTE: Aluminum building wire may be used but it must be rated for the correct amperage and voltage.

PROCEED TO STEP 8.

6 4-WIRE INSTALLATION (SEPARATE GROUND WIRE) WARNING

The neutral wire of the supply circuit must be connected to the neutral terminal located in the lower center of the terminal block. The power leads must be connected to the lower left and the lower right terminals of the terminal block. The grounding lead must be connected to the frame of the range with the ground plate and the green ground screw.

FOR POWER CORD INSTALLATION A. Remove the 3 lower screws from the

terminal block. Do not loosen the upper screws.

B. Remove the ground screw and ground plate and retain them.

C. Cut the ground strap below the terminal block and discard the lower section.

D. Insert the ground screw through the ground plate (removed earlier) and back into the range frame. Tighten securely, but do not over-tighten (15 to 20 in-lbs.)

E. Insert the 3 terminal screws through each power cord terminal ring and back into the terminal block. Be certain the white wire is in the center. Securely tighten each screw (35 to 50 in-lbs.

F. Reinstall terminal block cover.

FOR CONDUIT INSTALLATION A. Remove the 3 lower screws from the terminal

block. Do not loosen the upper screws. B. Remove the ground screw and ground plate

and retain them. C. Cut the ground strap below the terminal block

and discard the lower section. D. Insert the bare ground bare wire tip (insulation

stripped 5/8) between the range frame and the ground plate (removed earlier) and secure it in place with the ground screw. Tighten securely, but do not over-tighten (15 to 20 in-lbs).

E. Insert the wire tips (insulation stripped 5/8) into the bottom terminal block openings. Be certain the white wire is in the center. On certain models, the wire must be inserted through an opening in the ground strap. Securely tighten each screw onto each wire (35 to 50 in-lbs.)

F. Reinstall terminal block cover. NOTE: Aluminum building wire may be used but it must be rated for the correct amperage and voltage.

7 ANTI-TIP DEVICE INSTALLATION To reduce the risk of tipping the range, the range must be secured by a properly installed anti-tip bracket. See installation instructions shipped with the bracket for complete details before attempting to install.

To check if the bracket is installed and engaged properly, look underneath the range to see that the rear leveling

leg is engaged in the bracket. On some models, the storage drawer or kick panel can be removed for easier inspection. If visual inspection is not possible, slide the range forward, confirm the anti- tip bracket is securely attached to the floor or wall, and slide the range back so the leveling leg is under the anti-tip bracket. If the range is pulled from the wall for any reason, always repeat this procedure to verify the range is properly secured by the anti-tip bracket. Never completely remove the leveling legs or the range will not be secured to the anti-tip bracket.

9 FINAL INSTALLATION CHECKLIST Check to make sure the circuit breaker is closed (RESET) or the circuit fuses are replaced.

Be sure power is in service to the building.

Check that all packing materials and tape have been removed. This will include tape on metal panel under control knobs (if applicable), adhesive tape, wire ties, cardboard and protective plastic. Failure to remove these materials could result in damage to the appliance once the appliance has been turned on and surfaces have heated.

Check that the door and drawer are parallel to each other and that both operate smoothly. If they do not, see the Owners Manual for proper replacement.

Check to make sure that the rear leveling leg is fully inserted into the Anti-Tip bracket and that the bracket is securely installed.

OPERATION CHECKLIST Check that the oven control operates properly. If the oven control does not operate properly,

recheck the wiring connections.

Be sure all range controls are in the OFF position before leaving the range.

Anti-Tip Bracket Kit Included

Ground strap

Terminal block (appearance may vary)

Neutral terminal

Power cord

Ground plate

Power Cord

Red or Black

Red or Black

White

Terminal block

Red or Black

Red or Black

Neutral terminal

Ground plate (grounding to range)

Ground screw

AfterPower Cord

Green or Bare

White

BeforePower Cord and Conduit

Terminal block

Neutral terminal

Ground strap

Ground strap

or

INSTALLATION INSTRUCTION 31-2000948 07-21 GEA

JBS10, JBS30, JBS45, RB525, RB526, RBS160, RBS330, RBS360, JBS160, JBS360, JBS460, JB255, JB256,

JB450, JB480, VBS160, and XBS360

WARNING Before

beginning the installation, switch power off at service panel and lock the service disconnecting means to prevent power from being switched on accidentally. When the service disconnecting means cannot be locked, securely fasten a prominent warning device, such as a tag, to the service panel.

A child or adult can tip the range and be killed. Install the anti-tip bracket to the wall or floor. Engage the range to the anti-tip bracket by sliding the range back such that the foot is engaged. Re-engage the anti-tip bracket if the range is moved. Failure to do so can result in death or serious burns to children or adults.

Tip-Over Hazard WARNING

AfterConduit

Terminal block Ground plate

(grounding to range)Wire

tips

Ground screw

Red or Black

Red or Black

White

Green or Bare

Wire tips

Terminal block

Conduit

Conduit

Red or Black Red or

BlackWhite

A child or adult can tip the range and be killed. Install the anti-tip bracket to the wall or floor. Engage the range to the anti-tip bracket by sliding the range back such that the foot is engaged. Re-engage the anti-tip bracket if the range is moved. Failure to do so can result in death or serious burns to children or adults.

Tip-Over Hazard WARNING

8 LEVEL THE RANGE WARNING

Never completely remove the leveling leg as the range will not be secured to the anti-tip device properly. A. Plug in the unit. B. Measure the height of your countertop at the

rear of the opening (X). C. Adjust two rear leveling legs so that the rear

of cooktop is at the same height or higher than the counter (Y).

D. Slide unit into place. E. Install oven shelves in the oven and position

the range where it will be installed. F. Check for levelness by placing a spirit

level on one of the oven shelves. Take two readingswith the level placed diagonally first in one direction and then the other.

G. Adjust front leveling legs until the range is level.

H. Look under the unit and verify that the rear leg is fully engaged with the anti-tip device. If not, remove the unit and adjust the height of the rear leg so that it is properly engaged.

Spirit level

NOTE: Cooktop must be at or above counter.

Cooktop 0 or Greater

Counter

Rear of Range

Terminal Block Cover Screws to

remove terminal block cover

30

8 1/2

Install the outlet box on either side of the CL

36 1/4

46 3/4

30

3 3 3

9 8

4

2 1/47 1/2

2 1/4

Recommended acceptable electrical outlet area. Orient the electrical receptacle so the length is parallel to the floor.

29 with handle

26 1/4 w/o handle

A

NOTE C

B

A

C Both Sides

X

Y

3 REQUERIMIENTOS ELCTRICOS ADVERTENCIA Esta unidad debe contar con una adecuada conexin a tierra.

ADVERTENCIA Todas las construcciones nuevas, casas rodantes, vehculos recreativos e instalaciones donde los cdigos locales no permiten una conexin a tierra a travs de un neutral requieren un cable para cocina de 4 conductores aprobado por UL.

ADVERTENCIA Para prevenir un incendio o descarga elctrica, no utilice un cable

de extensin con este aparato.

ADVERTENCIA Para prevenir una descarga elctrica, quite el fusible o abra el interruptor de

circuitos antes de comenzar la instalacin. Recomendamos que un electricista calificado conecte el cableado elctrico y su cocina. Despus de la instalacin, solicite al electricista que le indique cmo desconectar la energa de la cocina.

Usted debe usar un sistema elctrico de 60 hercios CA de fase nica de 120/280 voltios o 120/240 voltios. Si tiene una conexin con cableado de aluminio, deben utilizarse conectores adecuadamente instalados para utilizar con cableado de aluminio. Si el servicio elctrico provisto no cumple con las especificaciones anteriores, haga que un electricista con licencia instale un tomacorriente aprobado. Vigente desde el 1 de enero de 1996, el Cdigo Elctrico Nacional requiere que las nuevas construcciones (no existentes) utilicen una conexin de cuatro conductores a una cocina elctrica. Cuando instale una cocina elctrica en una nueva construccin, una casa rodante, un vehculo recreativo o un rea donde los cdigos locales prohben la conexin a tierra a travs de un conductor neutral, consulte la seccin sobre conexiones en circuito derivado de cuatro conductores. Consulte a las empresas de servicio pblico sobre los cdigos elctricos que se aplican en su rea. No realizar el cableado de su horno de acuerdo con los cdigos vigentes puede provocar una situacin peligrosa. Si no existen cdigos locales, su cocina debe contar con cables y fusibles que cumplan con los requisitos del Cdigo Elctrico Nacional, ANSI/NFPA No. 70ltima edicin. Este electrodomstico debe recibir el voltaje y frecuencia adecuados, y debe conectarse a un circuito derivado individual con adecuada conexin a tierra de 40 amperios (mnimo) protegido por un interruptor de circuitos o fusible con retraso. Utilice slo un cable para cocinas de 3 o 4 conductores aprobado por UL. Estos cables pueden contar con terminales de anillo en alambre y un dispositivo de alivio de tensin. Se requiere un cable para cocinas clasificado para 40 amperios con rango de voltios mnimo de 125/250. No se recomienda un cable de 50 amperios, pero si se utiliza, debe sealizarse para usarse con aberturas de conexin de un dimetro nominal de 1-3/8. Debe tenerse cuidado al centrar el cable y el alivio de tensin dentro del orificio de expulsin para evitar que el borde dae el cable. La placa de clasificacin se encuentra ubicada sobre el cajn de almacenamiento en el marco del horno o en el lado del marco del cajn. NOTA: No se recomienda para este producto el uso de interruptores automticos, inalmbricos o con cableado externo que apagan la corriente del electrodomstico.

Placa de clasificacin

HORNO SIMPLE

ANTES DE COMENZAR Lea estas instrucciones por completo y con detenimiento.

IMPORTANTE Guarde estas instrucciones para el uso de inspectores locales.

IMPORTANTE Siga todos los cdigos y ordenanzas vigentes.

Nota al instalador Asegrese de dejar estas instrucciones con el consumidor.

Nota al consumidor Conserve estas instrucciones para referencia futura.

Nivel de destreza La instalacin de este aparato debe efectuarla un instalador o electricista calificado.

El instalador tiene la responsabilidad de efectuar una instalacin adecuada.

La garanta no cubre las fallas del producto debido a una instalacin incorrecta.

Instrucciones de instalacin Cocinas elctricas empotrables

MATERIALES QUE PUEDE NECESITAR HERRAMIENTAS NECESARIAS

(Aprobados por UL de 40 AMP) Cable de 4 alambres de 4

de largo O Cable de 3 alambres de 4 de largo

Conector de presin (Slo para instalaciones

con conductos portacables)

1 QUITE LOS MATERIALES DE ENVO: No quitar los materiales de empaque puede provocar daos al electrodomstico. Quite todas las partes de empaque del horno, bandejas, elementos calentadores y cajn. Tambin, quite la pelcula protectora y las etiquetas de la puerta exterior, estufa y panel de control.

Tenga en cuenta las opciones de reciclaje del material de embalaje de su electrodomstico.

Perforadora con broca de 1/8

Gafas de seguridad

Llave ajustable

Nivel

Tijeras para hojalata

Cinta mtrica

Alicates

Llave de tuercas de 1/4

PARA SU SEGURIDAD

ADVERTENCIA Antes de

comenzar la instalacin, apague el encendido en el panel de servicio y bloquee el medio de desconexin del servicio a fin de evitar que el encendido se active de forma accidental. Cuando el medio de desconexin del servicio no se pueda bloquear, ajuste de manera segura un tem de advertencia que est bien visible, tal como una etiqueta, sobre el panel de servicio.

Si no recibi un soporte anti volcaduras con su compra, llame al 1.800.626.8774 para recibir uno sin costo. (En Canad, llame al 1.800.561.3344). Para recibir instrucciones de instalacin del soporte, visite: GEAppliances.com (En Canad, GEAppliances.ca.).

4 INSTALACIN DE CABLE DE ENERGA Y DE PASACABLES

A Quite la tapa del cable (en la parte trasera de la cocina) quitando tornillos mediante una llave de tuercas de 1/4. Usted puede acceder el bloque terminal quitando la tapa del bloque terminal (en algunos modelos) o la tapa de los cables. No elimine esos tornillos.

B Para cable de energa y pasacables de 1 solamente, quite el anillo de expulsin (1-3/8) ubicado en el soporte directamente debajo del bloque terminal. Para quitar el anillo, utilice un par de alicates para doblar el anillo de expulsin lejos del soporte y gire hasta remover el anillo.

D Slo para instalaciones con conducto portacables de 3/4, adquiera un conector de presin que se ajuste al dimetro de su conducto e instlelo en el orificio. Introduzca el conducto a travs del conector de presin y ajuste. Deje un largo suficiente para poder pegar los cables al bloque terminal. NOTA: No instale el conducto sin un conector de presin. El conector de presin DEBER ser instalado antes de volver a instalar el bloque terminal trasero.

SIGA CON EL PASO 6 O 7.

Anillo de expulsin en el soporte

Anillo de expulsin quitado

Bloque terminal (la apariencia puede cambiar)

C Slo para instalaciones de cable de energa (ver el paso siguiente si utiliza un conducto portacables), instale el alivio de tensin en el orificio. Introduzca el cable de energa a travs del alivio de tensin y ajuste. Deje un largo suficiente para poder conectar las terminales de cable al bloque terminal. Si hay lengetas al final del alivio de tensin con alas, stas pueden quitarse para un ajuste mejor.

NOTA: No instale el cable de energa sin un alivio de tensin. El soporte del alivio de tensin DEBE instalarse antes de volver a colocar la tapa del cableado trasero de la cocina.

Cable de energa

Alivio de tensin

Bloque terminal

Soporte

7 INSTALACIN DE DISPOSITIVO ANTI-VOLCADURAS A fin de reducir el riesgo de inclinar la cocina, sta deber estar asegurada con un soporte anti volcaduras. Lea las instrucciones de instalacin que se enviaron con el soporte para obtener un detalle completo antes de comenzar la instalacin.

A fin de controlar que el soporte est instalado y adosado correctamente, retire el cajn de almacenaje o la parte inferior delantera y observe debajo de la cocina que

la pata niveladora est adosada al soporte. En modelos que no poseen un cajn de almacenaje o parte inferior delantera, incline con cuidado la cocina hacia adelante. El soporte debera detener la cocina dentro de las cuatro pulgadas. De no ser as, el soporte deber ser instalado nuevamente. Si la cocina es expulsada de la pared por alguna razn, siempre repita este procedimiento a fin de verificar que est asegurado de forma correcta con un soporte anti volcaduras. Nunca elimine completamente las patas niveladoras, ya que de ser as la cocina no estar adecuadamente asegurada por el dispositivo anti volcaduras.

9 LISTA DE CONTROL FINAL DE LA INSTALACIN Verifique que el interruptor de circuitos se encuentre cerrado (RESET) o que los fusibles del circuito se hayan

reemplazado.

Asegrese de que se cuente con suministro elctrico en el edificio.

Controle que se haya quitado todo el material de empaque y la cinta. Esto incluye cinta sobre el panel de metal bajo las perillas de control (si corresponde), cinta adhesiva, ataduras de alambre, cartn y plstico protector. No quitar estos materiales puede provocar daos al electrodomstico una vez que el aparato se haya encendido y las superficies se hayan calentado.

Controle que la puerta y el cajn se encuentren paralelos y que los dos funcionen correctamente. Si no es as, consulte el Manual del propietario para un reemplazo adecuado.

Controle que la pata de nivelacin trasera est bien introducida dentro del soporte anti-volcaduras y que el soporte se encuentre bien instalado.

LISTA DE CONTROL DE FUNCIONAMIENTO Controle que el control del horno funcione correctamente. Si el control del horno no funciona de forma correcta,

vuelva a controlar las conexiones de los cables.

Asegrese de que los controles de la cocina se encuentren en la posicin OFF (apagado) antes de alejarse de la cocina.

5 INSTALACIN DE TRES (3) ALAMBRES (LA CONEXIN A TIERRA SE REALIZA A TRAVS DEL CABLE NEUTRO)

ADVERTENCIA Riesgo de Descarga

El cable neutro y la cinta de conexin a tierra deben estar conectados como se muestra a continuacin, de modo que la cocina est correctamente conectada a tierra. No retire la cinta de conexin a tierra. Si no se siguen estas instrucciones, podrn existir riesgos de descarga elctrica.

ADVERTENCIA Riesgo de incendio

Los tornillos del bloque terminal deben estar ajustados de forma segura. Si esto no se cumple, existen riesgos de incendio.

PARA INSTALACIN DE CABLE DE ENERGA A. Retire los 3 tornillos inferiores del bloque terminal.

No afloje los tornillos superiores. B. No corte ni retire la cinta de conexin a tierra. C. Inserte los 3 tornillos a travs de cada anillo terminal

del cable de corriente y nuevamente al bloque terminal. Asegrese de que el cable blanco se encuentre en el centro. Ajuste de forma segura cada tornillos (entre 35 y 50 pulgadas/libra).

PARA INSTALACIN DE CONDUCTO PORTACABLES A. Afloje los 3 tornillos inferiores del bloque terminal. No afloje

los tornillos superiores. B. No corte ni retire la cinta de conexin a tierra. C. Inserte la punta del cable pelado (sin aislante de 5/8) en

las aberturas inferiores del bloque terminal. Asegrese de que el cable blanco se encuentre en el centro. En ciertos modelos, el cable deber ser insertado a travs de una abertura de la cinta de conexin a tierra. Ajuste de forma segura cada tornillo en cada cable (entre 35 y 50 pulgadas/ libra).

D. Reinstale la tapa del bloque terminal. NOTA: Puede utilizarse cable de construccin de aluminio pero debe clasificarse para el amperaje y voltaje correctos.

SIGA CON EL PASO 8.

6 INSTALACIN DE 4 ALAMBRES (CABLE DE CONEXIN A TIERRA SEPARADO)

ADVERTENCIA El cable neutral del

circuito de suministro debe estar conectado a la terminal neutral ubicada en el centro inferior del bloque terminal. Los cables de energa deben estar conectados a las terminales inferior izquierda e inferior derecha del bloque terminal. El cuarto cable a tierra debe estar conectado al marco de la cocina con la placa de conexin a tierra y el tornillo a tierra.

PARA INSTALACIN DE CABLE DE ENERGA A. Retire los 3 tornillos inferiores del bloque

terminal. No afloje los tornillos superiores. B. Retire el tornillo de conexin a tierra y la placa

de conexin a tierra y retenga los mismos. C. Corte la cinta de conexin a tierra que est debajo

del bloque terminal, y descarte la seccin inferior. D. Inserte el tornillo de conexin a tierra, a travs

de la placa de conexin a tierra (retirada anteriormente) y nuevamente en la estructura de la cocina. Ajuste de forma segura, pero sin ajustar en exceso (entre 15 y 20 pulgadas/libra).

E. Inserte los 3 tornillos de la terminal a travs de cada anillo terminal del cable de corriente y nuevamente al bloque terminal. Asegrese de que el cable blanco se encuentre en el centro. Ajuste de forma segura cada tornillo (entre 35 y 50 pulgadas/libra).

F. Reinstale la tapa del bloque terminal.

PARA INSTALACIN DE CONDUCTO PORTACABLES A. Retire los 3 tornillos inferiores del bloque

terminal. No afloje los tornillos superiores. B. Retire el tornillo de conexin a tierra y la placa de

conexin a tierra y retenga los mismos. C. Corte la cinta de conexin a tierra que est debajo

del bloque terminal, y descarte la seccin inferior. D. Inserte la punta del cable descubierto de conexin

a tierra (sin aislante de 5/8) entre el marco de la cocina y la placa de conexin a tierra (retirada previamente) y asegure el mismo con el tornillo de conexin a tierra. Ajuste de forma segura, pero sin ajustar en exceso (entre 15 y 20 pulgadas/libra).

E. Inserte las puntas de los cables (sin aislante de 5/8) en las aberturas inferiores del bloque terminal. Asegrese de que el cable blanco se encuentre en el centro. En ciertos modelos, el cable deber ser insertado a travs de una abertura de la cinta de conexin a tierra. Ajuste de forma segura cada tornillo en cada cable (entre 35 y 50 pulgadas/libra).

F. Reinstale la tapa del bloque terminal. NOTA: Puede utilizarse cable de construccin de aluminio pero debe clasificarse para el amperaje y voltaje correctos para poder realizar la conexin.

Cinta de conexin a tierra

Bloque terminal (la apariencia puede cambiar) Terminal neutral

Cable de energa

Placa de conexin a tierra

Cable de energa

Rojo o Negro

Rojo o Negro

Blanco

Puntas de los cables

Bloque terminal

Conducto portacables

Conducto portacables

Rojo o Negro Rojo o

NegroBlanco

Bloque terminal

Rojo o Negro

Rojo o Negro

Terminal neutral

Placa de conexin a tierra (conexin a tierra de la cocina)

Tornillo de conexin a tierra

DespusCable de energa

Verde o Pelado

Blanco

AntesCable de energa y conducto portacables

Bloque terminal

Terminal neutral

Cinta de conexin a tierra

Cinta de conexin a tierra

o

DespusConducto portacables

Bloque terminal Placa de conexin

a tierra (conexin a tierra de la cocina)Puntas

de los cables

Tornillo de conexin a tierra

Rojo o Negro

Rojo o Negro

Blanco

Verde o Pelado

INSTRUCCIONES DE INSTALACIN 31-2000948 07-21 GEA

JBS10, JBS30, JBS45, RB525, RB526, RBS160, RBS330, RBS360, JBS160, JBS360, JBS460, JB255, JB256,

JB450, JB480, VBS160, and XBS360

Kit de soporte anti-volcaduras

incluido Un nio o adulto pueden volcar la cocina y morir. Instale el soporte anti-volcaduras sobre la pared o el piso. Asegrese la estufa al soporte anti-volcaduras deslizando la unidad hacia atras de tal manera que la pata niveladora sea enganchada. Vuelva a adherir el soporte anti-volcaduras si la estufa se mueve de lugar. Si esto no se hace, se podr producir la muerte o quemaduras graves en nios o adultos.

Riesgo de Cada ADVERTENCIA

Un nio o adulto pueden volcar la cocina y morir. Instale el soporte anti-volcaduras sobre la pared o el piso. Asegrese la estufa al soporte anti-volcaduras deslizando la unidad hacia atras de tal manera que la pata niveladora sea enganchada. Vuelva a adherir el soporte anti-volcaduras si la estufa se mueve de lugar. Si esto no se hace, se podr producir la muerte o quemaduras graves en nios o adultos.

Riesgo de Cada ADVERTENCIA

2 CMO PREPARAR LA ABERTURA (PARA USO EN EL INTERIOR SOLAMENTE)

Ver ilustraciones con todas las dimensiones de empotrado y de espacio. La cocina puede ubicarse con un espacio de 0 (alineado) sobre la pared trasera y las paredes laterales del gabinete.

NOTA: Utilice un cable de energa de 4 para evitar una interferencia con el cajn de almacenamiento. Los cables de energa de 412 a 6 de largo pueden tener que cubrirse para poder cerrar el cajn correctamente.

DIMENSIONES MNIMAS ENTRE LA ESTUFA, LAS PAREDES Y SOBRE LA PARTE SUPERIOR DE LA ESTUFA: A. Verifique que el revestimiento de las paredes, el mostrador, el

piso y los gabinetes ubicados alrededor de la cocina puedan soportar el calor (hasta 200F) generado por la cocina. 0 para gabinetes debajo de la superficie de coccin y para la parte trasera de la cocina.

B. Deje un espacio de 30 como mnimo entre las unidades de superficie y la parte inferior de gabinetes de madera o de metal sin proteccin o deje un mnimo de 24 cuando la parte inferior del gabinete de madera o metal se encuentre protegida por cartn aislante de un grosor no menor a 1/4 y con retardo de llama cubierto con una placa de metal no menor a MSG N 28, acero inoxidable de un grosor de .015, aluminio de .024 o cobre de .020.

C. Este aparato ha sido aprobado para un espacio de 0 respecto de superficies adyacentes sobre la estufa. Sin embargo, se recomienda un espacio mnimo de 6 respecto de superficies menores a 15 sobre la estufa y gabinete adyacente para reducir la exposicin al vapor, salpicaduras de grasa y calor.

Para reducir el riesgo de quemaduras o incendios cuando se incline sobre los elementos de superficie calientes, debe evitarse la instalacin de espacios de almacenamiento en gabinetes sobre la estufa. Si debe contarse con espacio para almacenamiento en gabinetes sobre la estufa, puede reducirse el riesgo instalando una campana de cocina que sobresalga por lo menos 5 ms all del frente de los gabinetes. Los gabinetes instalados por encima de la estufa no deben tener una profundidad mayor a los 16.

Conector de presin

Bloque terminal

Conducto portacables

Soporte

8 NIVELACIN DE LA COCINA ADVERTENCIA

Nunca retire completamente las patas niveladoras, ya que la cocina no estar asegurada de forma adecuada al dispositivo anti-volcaduras. A. Enchufe la unidad. B. Mida la altura de su mostrador de encimera en la

parte trasera de la abertura (X). C. Ajuste las dos patas de nivelacin traseras para

que la parte trasera de la estufa se encuentre a la misma altura o ms arriba que la mesada (Y).

D. Deslice la unidad en su lugar. E. Instale los estantes del horno en la unidad y

coloque la cocina donde se instalar. F. Controle la nivelacin colocando un nivel de

burbuja de aire sobre uno de los estantes del horno. Haga dos lecturascon el nivel ubicado en diagonal primero en una direccin y luego en la otra.

G. Ajuste las patas de nivelacin frontales hasta que la cocina quede nivelada.

H. Observe debajo de la unidad y verifique que la pata trasera est completamente adherida al dispositivo antivolcaduras. De no ser as, retire la unidad y ajuste la altura de la pata trasera de modo que quede correctamente adherida.

Nivel de Agua

NOTA: La placa de coccin debe estar a la misma altura o ms arriba que la mesada.

Mesada

0 o Superior

Placa de Coccin

Parte trasera de la cocina

Tapa del Bloque Terminal

Tornillos para retirar la tapa del bloque terminal

30

8 1/2

Instale la caja de distribucin sobre cualquier lado de la lnea central.

36 1/4

46 3/4

30

3 3 3

9 8

4

2 1/47 1/2

2 1/4

rea recomendada para una salida elctrica aceptable. Oriente el receptculo elctrico de modo que la longitud sea paralela al suelo.

29 with handle

Manualsnet FAQs

If you want to find out how the JB256 GE works, you can view and download the GE JB256 JB256DMBB Range Installation Instructions on the Manualsnet website.

Yes, we have the Installation Instructions for GE JB256 as well as other GE manuals. All you need to do is to use our search bar and find the user manual that you are looking for.

The Installation Instructions should include all the details that are needed to use a GE JB256. Full manuals and user guide PDFs can be downloaded from Manualsnet.com.

The best way to navigate the GE JB256 JB256DMBB Range Installation Instructions is by checking the Table of Contents at the top of the page where available. This allows you to navigate a manual by jumping to the section you are looking for.

This GE JB256 JB256DMBB Range Installation Instructions consists of sections like Table of Contents, to name a few. For easier navigation, use the Table of Contents in the upper left corner.

You can download GE JB256 JB256DMBB Range Installation Instructions free of charge simply by clicking the “download” button in the upper right corner of any manuals page. This feature allows you to download any manual in a couple of seconds and is generally in PDF format. You can also save a manual for later by adding it to your saved documents in the user profile.

To be able to print GE JB256 JB256DMBB Range Installation Instructions, simply download the document to your computer. Once downloaded, open the PDF file and print the GE JB256 JB256DMBB Range Installation Instructions as you would any other document. This can usually be achieved by clicking on “File” and then “Print” from the menu bar.