GE RAK320SP Power Supply Kit Installation Instructions PDF

1 of 8
1 of 8

Summary of Content for GE RAK320SP Power Supply Kit Installation Instructions PDF

230/208 VOLT ELECTRICAL SUPPLY A power supply kit must be used to supply power to the Zoneline unit. The appropriate kit is determined by the voltage, the means of electrical connection, and the amperage of the branch circuit. See the POWER CONNECTION CHART to conrm the appropriate kit.

All wiring, including installation of the receptacle, must be in accordance with the NEC, local codes, ordinances, and regulations.

IMPORTANT NOTES This unit must be properly connected to a grounded

circuit. The electrical rating marked on the power supply kit

must be the same as the supply branch circuit. Aluminum building wiring may present special

problemsconsult a qualified electrician. All wiring, including installation of the receptacle,

must be in accordance with the NEC, local codes, ordinances, and regulations.

Use ONLY the wiring size recommended for single outlet branch circuit.

Proper current protection is the responsibility of the owner.

Recommended branch circuit wire sizes*

Nameplate maximum circuit breaker size

AWG wire size**

15A 20A 30A

14 12 10

AWG American Wire Gauge * Single circuit breaker from main box

** Based on copper wire, single-insulated conductor at 60C

NOTE: Use copper conductors only.

Tandem 15 Amp

Perpendicular 20 Amp

Large Tandem 30 Amp

Power supply kit - Appearance may vary

230/208 volt receptacle configuration

15A 20A and 30A

31-5000693 Rev. 0 03-22 GEA

Installation Instructions for your new RAK315SP, RAK320SP, RAK330SP Power Supply Kit for Sub-base

Before you begin - Read these instructions completely and carefully. IMPORTANT OBSERVE ALL GOVERNING CODES AND ORDINANCES. Note to Installer Be sure to leave these instructions with the Consumer. Note to Consumer Keep these instructions with your Owners Manual for future reference.

Tools Needed Phillips Head Screw Driver

This kit is for use with 230/208 volt replacement GE Zoneline units only with previously installed sub- bases. NOTE: Use only with sub-base kits RAK204D15*, RAK204D20*, or RAK204D30*.

WARNING RISK OF ELECTRIC SHOCK. Disconnect the electrical power supply before wiring connections.

GE is a trademark of the General Electric Company. Manufactured under trademark license.

POWER CONNECTION CHART GE 230/208 Volt Power Supply Kit

Receptacle Circuit Protective Device

RAK315SP Tandem 15-Amp Time-Delay Fuse or Breaker

RAK320SP Perpendicular 20-Amp Time-Delay Fuse or Breaker

RAK330SP Large Tandem 30-Amp Time-Delay Fuse or Breaker

2

1. REMOVE ROOM FRONT Remove the room cabinet by pulling it out at the bottom to release it (1); then lift it up to clear the rail along the unit top (2).

3. CONCEAL POWER SUPPLY KIT SUB-BASE AND CHASEWAY

1. Remove the rectangular knockout at the bottom of the junction box. Remove the rectangular knockout at the right end of the sub-base.

2. Power Supply kit is placed between the two halves of the chaseway. Observe the orientation of the chaseway.

3. Align the screw holes and secure the halves together using two type A screws.

Slide the upper end of chaseway with wiring protruding into rectangular knockout opening in the junction box.Be sure chaseway ears are on the inside of the box.

Drive one type A screw through the junction box bottom into the chaseway ear hole.

Insert lower end of chaseway into rectangular hole in sub-base and slide to right into the rectangular knockout making sure chaseway ears are inside the sub-base.

Route wire toward the center of the sub-base. Drive one type A screw through the sub-base slotted

hole into chaseway ear hole.

2. REMOVE JUNCTION BOX COVER

Remove the junction box cover by removing the screw holding it to the assembly.

Installation Instructions FOR 230/208 VOLT ZONELINE POWER CORD CONNECTIONS ONLY

For GE Zoneline AZ45 & AZ65 Series Units

This kit must be used in conjunction with a GE junction box kit and sub base with chaseway.

Junction Box Cover

Junction Box

Screw Knockout

Sub-base

Knockout

Chaseway Cover

Chaseway

Power Supply Kit

3

4. INSTALL JUNCTION BOX

Install the junction box by engaging the tabs of the junction box with the slots on the control housing, align the screw hole at the top and drive the supplied screw until secure.

6. INSTALL JUNCTION BOX COVER

1. Replace and secure all front covers on the sub base. Do not pinch any wires.

2. Place the junction box cover in place. Replace the two screws removed earlier and tighten securely.

3. Replace the Zoneline front cabinet.

5. CONNECT THE CORDSET Plug in the connectors on the power supply kit into the corresponding mating connectors on the Zoneline. Be sure to locking tabs at the sides are engaged. Insert the plug into the receptacle inside the subbase.

NOTE: Power Supply Kit Appearance may vary RAK315SP will only have one power connector.

Installation Instructions ZONELINE SERIES POWER SUPPLY KIT

Slots on Control Housing

Tabs on Junction Box

15A 20A and 30A

4

Notes

ALIMENTATION LECTRIQUE 230/208 VOLTS Il est ncessaire dutiliser un ensemble de bloc dalimentation pour alimenter le Zoneline. Il est possible de dterminer lensemble appropri grce la tension lectrique, les moyens de raccord lectrique et lintensit du courant lectrique du circuit de drivation. Pour vous assurer quil sagit de lensemble adquat, consultez le TABLEAU DES CONNEXIONS LECTRIQUES.

Lensemble du cblage, y compris linstallation de la prise, doit tre ralis conformment au CNE, codes locaux, ordonnances et rglements.

OUTILS REQUIS Tournevis cruciforme

REMARQUES IMPORTANTES Il faut connecter correctement cette unit un circuit mis

la terre. Les caractristiques lectriques marques sur lensemble

de bloc dalimentation doivent tre les mmes que celles du circuit de drivation.

Un cblage de btiment en aluminium peut reprsenter des problmes particuliers; consultez un lectricien professionnel.

Lensemble du cblage, y compris linstallation de la prise, doit tre ralis conformment au CNE, codes locaux, ordonnances et rglements.

Utilisez UNIQUEMENT la dimension de cblage recommande pour un circuit de drivation de sortie simple.

Le propritaire est responsable de fournir un dispositif de protection ampre-mtrique adquat.

Dimensions de cble de circuit de drivation recommandes*

Plaque signaltique dimension maximale de disjoncteur

Dimension de de cble AWG**

15A 20A 30A

14 12 10

AWG jauge amricaine des fils * Disjoncteur simple du coffret principal ** En fonction dun conducteur isolement simple, fil en cuivre, 60 C

REMARQUE : utilisez des conducteurs en cuivre uniquement.

Ens. de bloc dalim. - Laspect peut varier

AVERTISSEMENT RISQUE DE DCHARGE LECTRIQUE. Dbranchez le bloc dalimentation avant de raliser les raccords.

31-5000693 Rev. 0 03-22 GEA

Avant de commencer - Lisez ces instructions attentivement et en entier. IMPORTANT OBSERVEZ TOUS LES CODES ET RGLEMENTS EN VIGUEUR. Note linstallateur Assurez-vous de laisser ces instructions au consommateur. Note au consommateur - Conservez ces instructions avec votre manuel dutilisation pour consultation ultrieure.

Instructions dinstallation pour votre nouvelle trousse de bloc dalimentation pour la sous-base

RAK315SP, RAK320SP, RAK330SP

Cette trousse doit tre seulement utilise avec les units de rechange Zoneline GE ayant une sous-base dj installe. REMARQUE : Utilisation uniquement avec les trousses de sous-base RAK204D15*, RAK204D20*, ou RAK204D30*..

15A 20A et 30A

Tandem 15 A

Perpendiculaire 20 A

Grande tandem 30 A

Configuration de prise 230/208 volts

TABLEAU DES RACCORDS LECTRIQUES

Ens. de bloc dalim. GE 230/208 volts du rceptacle

Disp. de protection des circuits

RAK315SP Tandem Disjoncteur ou fusible temporis de 15 A

RAK320SP Perpendiculaire Disjoncteur ou fusible temporis de 20 A

RAK330SP Grande Tandem

Disjoncteur ou fusible temporis de 30 A

2

Instructions dinstallation POUR RACCORDS DUN CORDON DALIMENTATION ZONELINE DE 230/208 VOLTS SEULEMENT

Pour modles dunits Zoneline GE AZ45 et AZ265

1. RETRAIT DU PANNEAU AVANT Retirez larmoire lectrique en la tirant par le bas et vers vous pour la dgager (1), soulevez-la ensuite pour la librer du rail situ au haut de lappareil (2).

3. DISSIMULATION DE LA SOUS- BASE DE LA TROUSSE DE BLOC DALIMENTATION ET DU CHEMIN DE FILS

1. Retirez lentre dfonable rectangulaire situe au bas de la boite de jonction. Retirez lentre dfonable rectangulaire la droite de la sous-base.

2. La trousse de bloc dalimentation est place entre les deux moitis du chemin de fils. Observez lorientation du chemin de fils.

3. Alignez les trous de vis et fixez les deux moitis ensemble avec deux vis de type A.

Glissez la partie suprieure du chemin de fils et le cblage dpassant dans louverture de lentre dfonable rectangulaire dans la boite de jonction. Assurez-vous que les pattes se retrouvent lintrieur de la boite.

Insrez une vis de type A au bas de la boite de jonction dans le trou de la patte du chemin de fils.

Insrez la partie infrieure du chemin de fils dans le trou rectangulaire de la sous-base et glissez-la vers la droite dans lentre dfonable rectangulaire en vous assurant que les pattes se retrouvent lintrieur de la sous-base.

Acheminez le cble vers le centre de la sous-base. Insrez une vis de type A dans le trou fente de la

sous-base dans le trou de la patte du chemin de fils.

2. RETRAIT DU COUVERCLE DE LA BOITE DE JONCTION

Retirez le couvercle de la boite de jonction en retirant la vis la fixant lassemblage.

Cette trousse doit tre utilise conjointement avec une trousse pour boite de jonction de GE et une sous-base

Couvercle de la boite de jonction

Boite de jonction

Vis Entre dfonable

Couvercle du

Trousse de bloc dalimentation

Sous-base

Entre dfonable

3

Instructions dinstallation MODLES ZONELINE TROUSSE DE BLOC DALIMENTATION

4. INSTALLATION DE LA BOITE

Installez la boite de jonction en insrant les languettes de la boite de jonction dans les fentes du coffrage du systme de commande puis alignez le trou de vis du dessus puis insrez la vis fournie pour scuriser le tout.

6. INSTALLATION DU COUVERCLE DE LA BOITE DE JONCTION

1. Rinstallez et fixez tous les couvercles frontaux de la sous-base. vitez le pincement des fils.

2. Rinstallez le couvercle de la boite de jonction. Rinstallez les deux vis retires auparavant et fixez- les fermement.

3. Rinstallez larmoire avant du Zoneline.

5. RACCORDEMENT DU CORDON AMOVIBLE

Branchez les connecteurs de la trousse de bloc dalimentation dans les connecteurs homologues correspondants du Zoneline. Assurez-vous que les languettes de blocage latrales sont enclenches.

Insrez la fiche dans le rceptacle situ lintrieur de la sous-base. REMARQUE : Trousse de bloc dalimentation lapparence peut tre diffrente; le modle RA315SP naura quun seul connecteur dalimentation.

Fentes du

systme de commande

Languet

Manualsnet FAQs

If you want to find out how the RAK320SP GE works, you can view and download the GE RAK320SP Power Supply Kit Installation Instructions on the Manualsnet website.

Yes, we have the Installation Instructions for GE RAK320SP as well as other GE manuals. All you need to do is to use our search bar and find the user manual that you are looking for.

The Installation Instructions should include all the details that are needed to use a GE RAK320SP. Full manuals and user guide PDFs can be downloaded from Manualsnet.com.

The best way to navigate the GE RAK320SP Power Supply Kit Installation Instructions is by checking the Table of Contents at the top of the page where available. This allows you to navigate a manual by jumping to the section you are looking for.

This GE RAK320SP Power Supply Kit Installation Instructions consists of sections like Table of Contents, to name a few. For easier navigation, use the Table of Contents in the upper left corner.

You can download GE RAK320SP Power Supply Kit Installation Instructions free of charge simply by clicking the “download” button in the upper right corner of any manuals page. This feature allows you to download any manual in a couple of seconds and is generally in PDF format. You can also save a manual for later by adding it to your saved documents in the user profile.

To be able to print GE RAK320SP Power Supply Kit Installation Instructions, simply download the document to your computer. Once downloaded, open the PDF file and print the GE RAK320SP Power Supply Kit Installation Instructions as you would any other document. This can usually be achieved by clicking on “File” and then “Print” from the menu bar.