GE CEB1599 PEB9159SJSS Microwave Installation Instructions PDF

1 of 8
1 of 8

Summary of Content for GE CEB1599 PEB9159SJSS Microwave Installation Instructions PDF

Installation Microwave Oven Instructions Built-In Trim Kits

1

BEFORE YOU BEGIN Read these instructions completely and carefully. IMPORTANT Save these instructions

for local inspectors use.

IMPORTANT Observe all governing codes and ordinances.

Note to Installer Be sure to leave these instructions with the Consumer.

Note to Consumer Keep these instructions for future reference.

Skill level Installation of this appliance requires basic mechanical and electrical skills.

Completion time 1 to 3 hours Proper installation is the responsibility of the installer. Product failure due to improper installation is not

covered under the Warranty. This kit is for use on models:PEB9159DJ, PEB9159SJ,

PEB9159EJ, CEB1599SJ.and CEB1599EL. This kit and microwave are approved for installation

alone or above any single electric wall oven. Do not mount adjacent (within 2 feet) to any range, cooktop, gas oven, or other microwave.

This product is to be installed 3 feet above floor level. Do not alter or modify any part of this kit or the oven. For easier installation and personal safety, we

recommend that two people install this microwave oven.

Unplug the microwave oven before attempting installation of this kit.

WARNING This oven must be plugged into a properly grounded 3-hole, 120 volt receptacle as required by the National Electrical Code.

WARNING Before beginning the installation, switch power off at service panel and lock the service disconnecting means to prevent power from being switched on accidentally. When the service disconnecting means cannot be locked, securely fasten a prominent warning device, such as a tag, to the service panel.

Questions? Call GE Appliances Answer Center at 800.626.2000 or Visit our Website at: GEAppliances.com

PARTS INCLUDED

NOTE: This kit has extra screws to prevent the technician from spending extra time locating a replacement in case they lose one during installation.

JX9152 and JX9153

PART QUANITY

Rear Duct 1

Bottom Duct

1

Trim Kit Frame 1

Rail 2

Short Screws 16 required

3 extra

Long Wood Screws 4 required

2 extra

CUTOUT DIMENSIONS

WARNING This trim kit uses air flow from the top, bottom and sides of the trim frame. Blocking the air flow can cause the microwave to function improperly and may cause damage to the microwave. Allow a 1 clearance beyond the edge of the trim kit frame to provide proper air flow. FOR INSTALLATION ABOVE A BUILT-IN OVEN: Microwave oven should be installed on a 3/8 plywood base and supported by 2x4 or 1x2 equivalent runners on all sides. Base must be capable of supporting a minimum of 100 lbs.

2

Installation Instructions

Min. depth with receptacle outside cutout 22 Min. depth with receptacle inside cutout 23 1/2 120 volt 60 Hertz grounded power receptacle.

TOOLS YOU WILL NEED

2 Phillips Screwdrivers (#1 & #2)

Drill with 3/32 Drill Bit Pencil

Level Tape Measure

Depth

Height

1 Overlap

Width

1 Overlap

1 Clearance beyond trim frame

(on all sides)

3 Min.

27models: 1 7/8 overlap 30models: 3 5/16 overlap

Bottom of trim kit must be minimum of 36 from floor

Dimen- sion

Trim Kit Cutout

27 30 Height 19 1/8 19 1/8 17 1/8 1/8 Width 26 7/8 29 3/4 23 1/4 1/8

GROUNDING INSTRUCTIONS This appliance must be grounded. In the event of an electrical short circuit, grounding reduces the risk of electric shock by providing an escape wire for the electric current. This appliance is equipped with a cord having a grounding wire with a grounding plug. The plug must be plugged into an outlet that is properly installed and grounded.Consult a qualified electrician or serviceman if the grounding instructions are not completely understood, or if doubt exists as to whether the appliance is properly grounded.

Improper use of the grounding plug can result in a risk of electric shock. Do not use an extension cord. If the power supply cord is too short, have a qualified electrician or serviceman install an outlet near the appliance.

Permanent and Correct Installation

3-Prong plug

Grounding pin

3-Prong receptacle

Grounded receptacle box

WARNING

ELECTRICAL REQUIREMENTS Product rating is 120 volts AC, 60 Hertz, 14 amps and 1.60 kilowatts. This product must be connected to a supply circuit of the proper voltage and frequency. Wire size must conform to the requirements of the National Electrical Code or the prevailing local code for this kilowatt rating. The power supply cord and plug should be brought to a separate 15 to 20 ampere branch circuit single grounded outlet. The outlet box should be located in the cabinet above the oven. The outlet box and supply circuit should be installed by a qualified electrician and conform to the National Electrical Code or the prevailing local code.

2 INSTALL THE RAILS Disconnect the microwave oven from the receptacle. Remove everything out of the microwave oven, including packing, Owners Manuals, turntable and turntable support. A protective film has been applied to some microwave oven and trim kits. If applied, remove the film. Turn over the microwave oven and secure the rails to oven Base Plate by inserting 4 short screws. Be careful not to scratch the microwave oven.

1 LOCATE AND INSTALL THE BASE PAN

Set Base Pan into the front cabinet microwave oven cutout and center it right and left. Push back until the front flange is against the cabinet front wall. Mount the Base Pan using 3 short screws.

3

Installation Instructions

Short Screw

Microwave Oven Bottom

Rail

Short Screw

Flanges Door

Base Pan Mounting Holes

3 INSTALL THE REAR DUCT 1. Gently return microwave oven to its upright position. 2. Remove screw A.

3. Align the rear duct with the back of microwave oven, as shown.

4. Slide 2 tabs into the slots on the right side of the back of microwave oven.

5. Use 2 short screws to secure top of rear duct to the back of microwave oven, as shown.

A. Rear duct tabs B. Slots

A B

A. Short screws (2) B. Rear duct C. Back of microwave oven

A B C

Screw A

7 INSTALL THE TRIM KIT FRAME 1. Position the assembled Trim Kit frame around the

oven. 2. Drill pilot holes using the drill (3/22). 3. Secure the Trim Kit by 4 long screws through the

trim kit into the cabinet by using a manual screw driver.

IMPORTANT- Start all screws before tightening any one screw. Do not overtighten screws since it can cause misalignment of top/side strips.

DE68-03364A 49-40762-2

4

Installation Instructions

06-17 GEA Printed in China

READ CAREFULLY. KEEP THESE INSTRUCTIONS.

8 REPLACE ANY LOOSE ITEMS 1. Your trim kit is now fully installed. Replace the

turntable and turntable support that was removed from inside the microwave oven.

2. Keep these installation instructions and extra screws for future reference and need. Do not place them in the microwave oven.

3. Replace the house fuse, or close the circuit breaker to restore power at the service panel.

6 SECURE THE RAILS TO THE CABINET

Ensure the Base Pan and Bottom Bracket front flanges are tight against the cabinet, and that the screws holes are aligned. Drive 4 short screws through the Base Pan and Rails into the cabinet

Short Screw

Mounting Holes

4 INSTALL THE MICROWAVE OVEN Plug the power cord into the wall receptacle. Slide the microwave oven assembly gently into the cabinet, using care not to pinch the power cord. Be sure to keep the assembly centered as it slides back to where the tongue of the rails goes through the slots on Base Plan. The top edges of the Base Plan should now be centered right to left in the opening. The Base should be tight against the cabinet.

5 CHECK LEVELING Check the leveling by placing a level at the front and sides of the microwave. It may be necessary to add wood shims under the base pan to level the microwave front-to- back and side-to-side.

Rail Guides

Rails

3 INSTALL THE REAR DUCT (continued)

6. Use 3 short screws to secure back of rear duct to the back of microwave oven, as shown.

A. Short screws (3) B. Rear duct C. Back of microwave oven

A B C

Long Screw

Instrucciones Kits de Horno Microondas con de Instalacin Terminaciones Incorporadas

1

ANTES DE COMENZAR Lea estas instrucciones en su totalidad y atentamente. IMPORTANTE Conserve estas

instrucciones para uso del inspector local. IMPORTANTE Cumpla con todos los

cdigos y ordenanzas gubernamentales. Nota para el Instalador Asegrese de que el

Comprador conserve estas instrucciones. Nota para el Comprador Conserve estas

instrucciones para referencia futura. Nivel de habilidad La instalacin de este

electrodomstico requiere un nivel bsico de habilidades mecnicas y elctricas.

Tiempo de instalacin entre 1 y 3 horas La correcta instalacin del producto es responsabilidad

del instalador. Si se producen fallas en el producto debido a una

instalacin inadecuada, la Garanta no cubrir las mismas.

Este kit es para uso en los modelos: PEB9159DJ, PEB9159SJ, PEB9159EJ, CEB1599SJ.y CEB1599EL.

El kit y el horno microondas estn aprobados para su instalacin en forma aislada o sobre cualquier horno elctrico de pared simple. No monte el mismo de forma adyacente (dentro de los 2 pies) a cualquier cocina, superficie de coccin, horno a gas, u otro microondas

Este producto se deber instalar a 3 pies de distancia del piso.

No altere ni modifique ninguna parte de este kit o del horno.

Para una instalacin ms fcil y por cuestiones de seguridad personal, recomendamos que la instalacin del horno microondas sea realizada por dos personas.

Desenchufe el horno microondas antes de intentar instalar este kit.

ADVERTENCIA Este horno deber estar correctamente

enchufado en un receptculo de 3 agujeros y 120V, de acuerdo con lo requerido por el Cdigo de Electricidad Nacional (National Electrical Code).

ADVERTENCIA Antes de comenzar con la instalacin, apague el interruptor del panel del

servicio y bloquee el suministro del servicio a fin de evitar que la corriente se active en forma accidental. Cuando el suministro del servicio no pueda ser bloqueado, ajuste de forma segura un dispositivo de advertencia visible, tal como una etiqueta, al panel del servicio.

Preguntas? Llame a 800.GE.CARES (800.432.2737) o Visite nuestro sitio web en: GEAppliances.com

JX9152 y JX9153

PIEZAS INCLUIDAS

NOTA: Este kit cuenta con tornillos adicionales a fin de evitar que el tcnico necesite tiempo adicional para ubicar un tornillo de reemplazo durante la instalacin.

PIEZA CANTIDAD

Conducto Trasero 1

Olla de la Base 1

Kit de Termi- naciones 1

Riel 2

Tornillos Cortos

16 requeri- dos

3 adicionales

Tornillos Largos de Madera

4 requeridos 2 adicionales

DIMENSIONES DE LA ABERTURA

ADVERTENCIA Este kit con terminacin usa el flujo de aire desde la parte superior, inferior o

los costados de la estructura con terminacin. Bloquear el flujo de aire puede hacer que el microondas funcione de forma inadecuada y ocasionar daos sobre el mismo.

Deje un espacio de 1 ms all del extremo de la estructura con terminacin para brindar el flujo de aire apropiado.

PARA LA INSTALACIN SOBRE UN HORNO EMPOTRABLE:

El horno microondas debera ser instalado en una base de contrachapado de 3/8 y contar con el soporte de tirantes equivalentes de 2 x 4 o 1 x 2 en todos los costados. La base deber poder soportar un mnimo de 100 libras.

2

Instrucciones de Instalacin

Profundidad mnima con el receptculo fuera de la abertura 22 Profundidad mnima con el receptculo dentro de la abertura 23 1/2

Receptculo de corriente con conexin a tierra, 120 voltios, 60 Hertz

HERRAMIENTAS QUE NECESITAR

2 Destornilladores Phillips (n 1 y n 2)

Agujeree con una broca de 3/32 Lpiz

Nivel Cinta mtrica

Profundidad

Altura

Superposicin de 1

Ancho

Superposicin de 1

Despeje de 1 ms all de la estructura con terminacin

(hacia todos los lados)

Mn. de 3

Modelos de 27: Superposicin de 1 7/8 Modelos de 30: Superposicin de 3 5/16

La parte inferior del kit con terminacin deber tener un mnimo de 36 desde el piso

Dimensin Kit de Terminaciones

Abertura 27 30

Altura 19 1/8 19 1/8 17 1/8 1/8 Ancho 26 7/8 29 3/4 23 1/4 1/8

INSTRUCCIONES DE CONEXIN A TIERRA Este electrodomstico deber estar conectado a tierra. En caso de que se produzca un cortocircuito, la conexin a tierra reduce el riesgo de descarga elctrica, brindando un cable de escape de la corriente elctrica. Este electrodomstico est equipado con un cable de corriente que posee un cable de conexin a tierra con un enchufe a tierra. El enchufe deber ser colocado en un tomacorriente correctamente instalado y conectado a tierra. Consulte a un electricista calificado o al personal del servicio tcnico en caso de no entender totalmente las instrucciones de conexin a tierra, o en caso de existir dudas de que el electrodomstico est correctamente conectado a tierra.

ADVERTENCIA El uso inadecuado del enchufe de

conexin a tierra puede provocar riesgos de descargas elctricas. No use un prolongador. Si el cable de corriente es demasiado corto, solicite a un electricista calificado o al personal del servicio tcnico que instale un tomacorriente cerca del electrodomstico.

Instalacin Permanente y Correcta

Enchufe de 3 clavijas

Clavija de conexin a tierra

Receptculo de 3 clavijas

Caja con receptculo conectado a tierra

REQUISITOS ELCTRICOS La graduacin del producto es de 120 volts AC, 60 Hertz, 14 amperes, y 1.60 kilowatts. Este producto se debe conectar a un circuito con un suministro correcto de voltaje y frecuencia. El tamao del cable deber ser conforme a los requisitos del Cdigo Elctrico Nacional o del cdigo local obligatorio con relacin a la cantidad de kilowatts. El cable y enchufe de suministro de corriente se debern conectar a un tomacorriente simple con conexin a tierra de un circuito de entre 15 y 20 amperes. La caja del tomacorriente deber ser ubicado en el gabinete sobre el horno. La caja del tomacorriente y el circuito de suministro debern ser instalados por un electricista calificado y cumplir con el Cdigo Elctrico Nacional o el cdigo local obligatorio.

2 INSTALACIN DE LOS RIELES Desconecte el horno microondas del receptculo. Retire todo lo que haya dentro del horno microondas, incluyendo el embalaje, Manuales del Propietario, el plato giratorio y el soporte del plato giratorio. Se aplic una pelcula protectora en algunos hornos microondas y kits con terminaciones. Si cuenta con la misma, retire la pelcula. D vuelta el horno microondas y asegure los rieles a la Placa de la Base del horno, insertando 4 tornillos cortos. Asegrese de no rayar el horno microondas.

1 UBIQUE E INSTALE UNA OLLA DE LA BASE

Coloque la Olla de la Base en la abertura del gabinete frontal del horno microondas y centre la misma sobre la derecha y la izquierda. Empuje hacia atrs hasta que la pestaa frontal quede contra la pared frontal del gabinete. Monte la Olla de la Base usando 3 tornillos cortos.

3

Instrucciones de Instalacin

Parte Inferior del Horno Microondas

Riel

Pestaas Puerta

3 INSTALACIN DEL CONDUCTO TRASERO

1. De forma suave gire el horno microondas hasta su posicin vertical.

2. Retire el tornillo A.

3. Alinee el conducto trasero con la parte trasera del horno microondas, como se muestra.

4. Deslice las 2 lengetas en las ranuras del lado derecho de la parte trasera del horno microondas.

5. Use 2 tornillos cortos para asegurar la parte superior del conducto trasero hasta la parte trasera del horno microondas, como se muestra.

6. Use 3 tornillos cortos para asegurar la parte trasera del conducto trasero hasta la parte trasera del horno microondas, como se muestra.

A. Lengetas del conducto trasero B. Ranuras

A B

A. Tornillos cortos (2) B. Conducto trasero C. Parte trasera del

horno microondas

A B C

Tornillos A

A. Tornillos cortos (3) B. Conducto trasero C. Parte trasera del

horno microondas

A B C

Tornillos cortos

Olla de la Base Agujeros de Montaje

Tornillos cortos

7 INSTALACIN DE LA ESTRUCTURA DEL KIT CON TERMINACIONES

1. Posicione la estructura ensamblada del Kit con Terminaciones alrededor del horno..

2. Haga agujeros piloto usando el taladro (3/22). 3. Asegure el Kit con Terminaciones con 4 tornillos largos,

a travs del kit con terminaciones hasta el gabinete, usando un destornillador manual.

IMPORTANTE - Ubique todos los tornillos antes de comenzar a ajustar el primero. No ajuste en exceso los tornillos, ya que esto podr ocasionar desalineaciones de las tiras superiores/ laterales.

DE68-03364A 49-40762-2 06-17 GEA Impreso en China

LEA DETENIDAMENTE. CONSERVE ESTAS INSTRUCCIONES.

8 REEMPLACE CUALQUIER TEM FLOJO

1. Su kit con terminacin se encuentra ahora completamente instalado. Reemplace el plato giratorio y su soporte correspondiente, que fueron retirados del interior del horno microondas.

2. Guarde estas instrucciones de instalacin y tornillos adicionales para referencia y uso futuro. No los coloque en el horno microondas.

3. Reemplace el fusible del hogar o cierre el disyuntor para reiniciar la corriente en el panel del servicio.

Screw Btornillo largo

6 ASEGURE LOS RIELES AL GABINETE

Asegure que la Olla de la Base y las lengetas frontales del Soporte Inferior estn ajustadas contra el gabinete, y que los agujeros de los tornillos estn alineados. Coloque 4 tornillos cortos a travs de la Olla de la Base y los Rieles sobre el gabinete.

Short Screw

Agujeros de Montaje

5 CONTROL DE LA NIVELACIN Controle la nivelacin colocando un nivel en el frente y los costados del horno microondas. Es posible que sea necesario agregar cuas de madera debajo de la olla de la base para nivelar el frente del microondas con la parte trasera o un costado con el otro.

4

Instrucciones de Instalacin

4 INSTALE EL HORNO MICROONDAS Enchufe el cable de corriente en el tomacorriente. Deslice el ensamble del horno microondas al gabinete de forma cuidadosa, teniendo cuidado de que no haya pellizcos sobre el cable de corriente. Asegrese de mantener el ensamble centrado a medida que se vuelve a deslizar hacia las lengetas de los rieles a travs de las ranuras de la Olla de la Base. Los extremos superiores de la Olla de la Base deberan ahora estar centrados de derecha a izquierda en la abertura. La Base debera estar ajustada contra el gabinete.

Riel Guas

Rieles

Manualsnet FAQs

If you want to find out how the CEB1599 GE works, you can view and download the GE CEB1599 PEB9159SJSS Microwave Installation Instructions on the Manualsnet website.

Yes, we have the Installation Instructions for GE CEB1599 as well as other GE manuals. All you need to do is to use our search bar and find the user manual that you are looking for.

The Installation Instructions should include all the details that are needed to use a GE CEB1599. Full manuals and user guide PDFs can be downloaded from Manualsnet.com.

The best way to navigate the GE CEB1599 PEB9159SJSS Microwave Installation Instructions is by checking the Table of Contents at the top of the page where available. This allows you to navigate a manual by jumping to the section you are looking for.

This GE CEB1599 PEB9159SJSS Microwave Installation Instructions consists of sections like Table of Contents, to name a few. For easier navigation, use the Table of Contents in the upper left corner.

You can download GE CEB1599 PEB9159SJSS Microwave Installation Instructions free of charge simply by clicking the “download” button in the upper right corner of any manuals page. This feature allows you to download any manual in a couple of seconds and is generally in PDF format. You can also save a manual for later by adding it to your saved documents in the user profile.

To be able to print GE CEB1599 PEB9159SJSS Microwave Installation Instructions, simply download the document to your computer. Once downloaded, open the PDF file and print the GE CEB1599 PEB9159SJSS Microwave Installation Instructions as you would any other document. This can usually be achieved by clicking on “File” and then “Print” from the menu bar.