GE RAG13A Grille Installation Instructions PDF

1 of 4
1 of 4

Summary of Content for GE RAG13A Grille Installation Instructions PDF

31-5000490 Rev. 0 03-20 GEA

Installation Instructions for your new

Before you begin - Read these instructions completely and carefully. IMPORTANT OBSERVE ALL GOVERNING CODES AND ORDINANCES. Note to Installer Be sure to leave these instructions with the Consumer. Note to Consumer Keep these instructions with your Owners Manual for future reference.

RAG13A Rear Grille

Tools Needed 1/4 Nut Driver Pliers

Prepare the wall case for installation of grille: 1. Remove the indoor protective cover from the wall

case, if present. 2. Remove the outdoor protective cover from the wall

case, if present. Remove the cover from inside the cabinet following the instructions on the cover.

3. If the air conditioner is already installed in the wall case, turn off the air conditioner, unplug the unit, and slide the unit out of the case.

CAUTION Risk of injury or property damage. To prevent the grille from falling, hold onto the ribbon on the grille. If there is no ribbon present, use pliers and wear gloves to hold the grille. 4. To remove an already installed grille, remove the

two screws at the bottom edge of the grille. Slide down one inch to free the top edge.

Parts Included Grille S clips (2) Screws (2)

NOTE: The grille can be installed from the inside after the cabinet is installed.

2

Installation Instructions

Installatation of new grille (for wall cases with external grille. Wall case models: RAB46A, RAB47A, RAB48A, RAB26A, and RAB26W) 1. Make sure that the grille edge facing up has two

tabs sticking up. 2. Using the ribbon to hold the grille, place the grille

completely through the cabinet so that it is outside. Angle the grille so that the top edge is against the top flange of the wall case.

Slot Location

Insert tabs on top of the grille into two slots on the top rear flange. Make sure that both tabs are through the slots and visible inside the case.

3. Line up the two plastic grommets in the bottom of the grille with holes in the bottom rear flange of the case. Secure with the two included screws from the inside.

Screws

4. Remove the ribbon from the grille.

Installatation of new grille (for wall cases with a recessed grille. Wall case models: RAB20, RAB46, RAB47, and RAB48) 1. Use the pliers to bend back the two tabs on the top

edge of the grille.

2. Install the S clips on the top rear flange of the case approximately 8 inches from each side. Clips fit through the hole in the flange.

88

S-CLIP

3. Using the ribbon, place the grille completely through the cabinet so that it is outside. Then pull back against the rear of the cabinet and insert the top of the grille up into the clips.

4. Line up the two plastic grommets in the bottom of the grille with holes in the bottom rear flange of the case. Secure with the two included screws from the inside.

Screws

5. Remove ribbon from the grille.

31-5000490 Rev. 0 03-20 GEA

Instructions pour linstallation de votre

Avant de commencer Lisez entirement et attentivement ces instructions . IMPORTANT OBSERVEZ TOUS LES CODES ET TOUTES LES ORDONNANCES EN VIGUEUR. Note linstallateur Veillez laisser ces instructions au consommateur. Note au consommateur Gardez ces instructions avec votre manuel de lutilisateur pour

RAG13A Nouvelle Grille

Outils ncessaires Tourne-crou de 64 mm ( po) Pinces

Prparez le botier mural pour linstallation de la grille 1. Enlevez du botier mural le revtement intrieur de

protection, sil y en a un. 2. Enlevez du botier mural le revtement extrieur

de protection, sil y en a un. Enlevez le couvercle partir de lintrieur du botier en suivant les instructions sur le couvercle.

3. Si le climatiseur est dj install dans le botier mural, arrtez le climatiseur, dbranchez-le et glissez-le hors du botier.

ATTENTION Risque de blessure corporelle ou de dommage aux biens. Pour viter que la grille ne tombe, tenez le ruban sur la grille. Sil ny a pas de ruban, utilisez une pince et portez des gants pour tenir la grille. 4. Pour enlever une grille dj installe, enlevez

les deux vis sur le bord du fond de la grille. Glissez de 2,54 cm (1 po) le bord suprieur vers le bas.

Pices incluses Grille Attache de type S (2) Vis (2)

NOTE: La grille peut tre installe de lintrieur aprs que le botier est install.

2

Instructions dinstallation

Installation de la nouvelle grille (Pour les botiers muraux avec une grille extrieure. Botiers muraux des modles: RAB46A, RAB47A, RAB48A, RAB26A, and RAB26W) 1. Assurez-vous que le bord de la grille face vers le

haut possde deux pattes qui dpassent. 2. Utilisation du ruban pour maintenir la grille, passez-

la au travers du botier pour quelle soit lextrieur. Inclinez la grille pour que bord suprieur sappuie sur le rebord suprieur du botier mural.

Slot Location

Insrez les pattes du haut de la grille dans les deux fentes du rebord arrire. Assurez-vous que les deux pattes sont dans les fentes et visibles de lintrieur du botier.

3. Alignez les deux illets en plastique au fond la grille sur les trous du rebord infrieur du botier. Fixez la grille de lintrieur laide des deux vis comprises.

Screws

4. Enlevez le ruban de la grille.

Installation de la nouvelle grille (Pour les botiers muraux avec une grille encastre. Botiers muraux des modles RAB20, RAB46, RAB47, and RAB48) 1. laide de pinces, pliez vers larrire les deux

pattes du bord suprieur de la grille.

2. Installez les attaches de type S sur le rebord suprieur arrire du botier environ 20,32 cm (8 po) de chaque ct. Les attaches se fixent travers les trous du rebord.

88

S-CLIP

3. laide le ruban, passez la grille travers le botier pour quelle soit lextrieur. Tirez-la ensuite cont

Manualsnet FAQs

If you want to find out how the RAG13A GE works, you can view and download the GE RAG13A Grille Installation Instructions on the Manualsnet website.

Yes, we have the Installation Instructions for GE RAG13A as well as other GE manuals. All you need to do is to use our search bar and find the user manual that you are looking for.

The Installation Instructions should include all the details that are needed to use a GE RAG13A. Full manuals and user guide PDFs can be downloaded from Manualsnet.com.

The best way to navigate the GE RAG13A Grille Installation Instructions is by checking the Table of Contents at the top of the page where available. This allows you to navigate a manual by jumping to the section you are looking for.

This GE RAG13A Grille Installation Instructions consists of sections like Table of Contents, to name a few. For easier navigation, use the Table of Contents in the upper left corner.

You can download GE RAG13A Grille Installation Instructions free of charge simply by clicking the “download” button in the upper right corner of any manuals page. This feature allows you to download any manual in a couple of seconds and is generally in PDF format. You can also save a manual for later by adding it to your saved documents in the user profile.

To be able to print GE RAG13A Grille Installation Instructions, simply download the document to your computer. Once downloaded, open the PDF file and print the GE RAG13A Grille Installation Instructions as you would any other document. This can usually be achieved by clicking on “File” and then “Print” from the menu bar.