GE RAK44 Curtain Guard Installation Instructions PDF

1 of 2
1 of 2

Summary of Content for GE RAK44 Curtain Guard Installation Instructions PDF

31-5000590 Rev. 0 03-21 GEA

1) Prepare the surface in which the curtain guard is to be applied by removing dirt, dust, grease, oil, or any other surface coating that may prevent adhesion. Avoid harsh chemical cleaning agents.

2) Take note of the curtain guard orientation in the figures below. The attachment tab of the curtain guard will be closest to the wall.

3) To determine placement, position the curtain guard on the unit. On AZ45/65 Zonelines, the curtain guard should be placed on the flat area above the discharge as opposed to the rounded surface directly above the discharge. Center the part left to right above the PTAC air discharge. Record this location using painters tape or by lightly marking the PTAC surface at both ends of the curtain guard with a pencil.

4) Remove the protective film covering the curtain guard.

5) Remove the backing tape from the adhesive strips on the curtain guard.

6) Aligning with one of your marks, carefully lay one end of the curtain guard down. Slowly lower the remaining portion, making sure that the curtain guard meets the other mark.

7) Use fingers to apply pressure to the curtain guard directly above the adhesive strips to ensure good attachment to the PTAC surface.

8) Remove painters tape or use an eraser to remove any pencil marks.

9) Position curtains in desired location behind the curtain guard.

Installation Instructions for your new

RAK44 Curtain Guard for AZ45/65 Series Zonelines and Hotpoint PTACs (Compatibility with other models may vary)

Before you begin - Read these instructions completely and carefully. IMPORTANT OBSERVE ALL GOVERNING CODES AND ORDINANCES. Note to Installer Be sure to leave these instructions with the Consumer. Note to Consumer Keep these instructions with your Owners Manual for future reference.

GE is a trademark of the General Electric Company. Manufactured under trademark license.

31-5000590 Rev. 0 03-21 GEA

1) Prparez la surface sur laquelle sera install le protge-rideaux en enlevant la salet, la poussire, la graisse, lhuile et tout autre enduit de surface pouvant provoquer ladhrence. vitez les produits nettoyants puissants.

2) Veuillez noter lorientation du protge-rideaux dans les illustrations ci-dessous. La languette de fixation du protge-rideaux sera plus prs du mur.

3) Pour dterminer lemplacement, placez le protge-rideaux sur lappareil. Pour les modles Zonelines AZ45/65, le protge-rideaux sera plac sur la surface plate au-dessus de lvacuation oppose la surface arrondie directement au-dessus de lvacuation. Centrez les parties gauche et droite sur le dessus de lvacuation dair du climatiseur monobloc. Marquez cet emplacement en utilisant du ruban de peintre ou en marquant lgrement la surface du climatiseur monobloc aux deux extrmits du protge-rideaux laide dun crayon.

4) Retirez la pellicule protectrice recouvrant le protge-rideaux.

5) Retirez le papier dorsal des bandes adhsives du protge-rideaux.

6) Alignez avec lune des marques effectues et dposez dlicatement une extrmit du protge-rideaux. Abaissez lentement lautre partie en vous assurant que le protge-rideaux rencontre lautre marque.

7) Appliquez une pression avec les doigts sur le protge-rideaux, directement au-dessus des bandes adhsives pour assurer une bonne fixation la surface du climatiseur monobloc.

8) Enlevez le ruban de peintre ou effacer les marques de crayon avec une efface.

9) Placez les rideaux lendroit dsir derrire le protge-rideaux.

Instructions dinstallation pour votre nouveau protge-rideaux

RAK44 pour climatiseurs monoblocs Zonelines AZ45/65 et Hotpoint (La compatibilit peut varier avec dautres modles)

GE is a trademark of the General Electric Company. Manufactured under trademark license.

Avant de commencer - Lisez ces instructions attentivement et en entier. IMPORTANT OBSERVEZ TOUS LES CODES ET RGLEMENTS EN VIGUEUR. Note linstallateur Assurez-vous de laisser ces instructions au consom

Manualsnet FAQs

If you want to find out how the RAK44 GE works, you can view and download the GE RAK44 Curtain Guard Installation Instructions on the Manualsnet website.

Yes, we have the Installation Instructions for GE RAK44 as well as other GE manuals. All you need to do is to use our search bar and find the user manual that you are looking for.

The Installation Instructions should include all the details that are needed to use a GE RAK44. Full manuals and user guide PDFs can be downloaded from Manualsnet.com.

The best way to navigate the GE RAK44 Curtain Guard Installation Instructions is by checking the Table of Contents at the top of the page where available. This allows you to navigate a manual by jumping to the section you are looking for.

This GE RAK44 Curtain Guard Installation Instructions consists of sections like Table of Contents, to name a few. For easier navigation, use the Table of Contents in the upper left corner.

You can download GE RAK44 Curtain Guard Installation Instructions free of charge simply by clicking the “download” button in the upper right corner of any manuals page. This feature allows you to download any manual in a couple of seconds and is generally in PDF format. You can also save a manual for later by adding it to your saved documents in the user profile.

To be able to print GE RAK44 Curtain Guard Installation Instructions, simply download the document to your computer. Once downloaded, open the PDF file and print the GE RAK44 Curtain Guard Installation Instructions as you would any other document. This can usually be achieved by clicking on “File” and then “Print” from the menu bar.