GE JEP5036 JP3030TJWW Cooktop Installation Instructions PDF

1 of 16
1 of 16

Summary of Content for GE JEP5036 JP3030TJWW Cooktop Installation Instructions PDF

Installation Instructions

BEFORE YOU BEGIN Read these instructions carefully and completely.

IMPORTANT Save these instructions for local inspectors use.

IMPORTANT Observe all governing codes and ordinances.

Note to Installer Be sure to leave these instructions with the consumer.

Note to Consumer Keep these instructions for future reference.

Product failure due to improper installation is not covered under the Warranty.

WARNING This appliance must be properly grounded.

ATTENTION INSTALLER ALL COOKTOPS MUST BE HARD WIRED

(DIRECT WIRED) INTO AN APPROVED JUNCTION BOX. A PLUG AND RECEPTACLE IS NOT PERMITTED ON THESE PRODUCTS.

Proper installation is the responsibility of the installer and product failure due to improper installation is NOT covered under warranty.

30 and 36 Electric Cooktop - Radiant Excludes Down-Draft Models

MATERIALS YOU WILL NEED

TOOLS NEEDED

CUTTING THE COUNTERTOP If you are installing the cooktop in a solid surface material such as granite, quartz or any other natural or synthetic solid surface, we recommend that the cutout be prepared by a professional cabinet or countertop installer. Cooktop cutouts in wood or wood-laminate countertops may be able to be prepared using a saber saw and electric drill.

PARTS INCLUDED

31-11072-4 01-19 GEA

Wire NutsJunction Box

Saber Saw

Pencil

Safety Glasses

1/8 Drill Bit & Electric or Hand Drill

Ruler or Straightedge

Phillips Head Screwdriver

2 Hold Down Brackets

4 Screws (WB01X1137)

Foam Tape WB06K5042

90 or Straight Squeeze Connector

for 1 Conduit

Questions? Call us at 1.800.432.2737 or visit GEAppliances.com. In Canada, call 1.800.561.3344 or visit GEAppliances.ca.

2 31-11072-4

Installation Instructions IMPORTANT SAFETY INSTRUCTIONS

FOR YOUR SAFETY For Personal Safety, remove house fuse or open

circuit breaker before beginning installation. Failure to do so could result in serious injury or death.

Be sure your cooktop is installed properly by a qualified installer or service technician.

To eliminate the risk of burns or fire due to reaching over heated surface elements, cabinet storage located above the surface units should be avoided. If cabinet storage space is to be provided, the risk can be reduced by installing a range hood that projects horizontally a minimum of 5" beyond the bottom of the cabinets. Cabinet installation above the cooktop may be no deeper than 13".

Make sure the cabinets and wall coverings around the cooktop can withstand the temperatures (up to 200F) generated by the cooktop.

The cooktop should be easy to reach and lighted with natural light during the day.

Always disconnect the electrical service to the cooktop before repairing or servicing the cooktop. This can be done by disconnecting the fuse or circuit breaker. Failure to do this could result in a dangerous or fatal shock. Know where your main disconnect switch is located. If you do not know, have your electrician show you.

ELECTRICAL REQUIREMENTS This appliance must be supplied with the proper voltage and frequency, and connected to an individual, properly grounded branch circuit, protected by a circuit breaker or a time delay fuse as noted on name plate and the chart below. We recommend you have the electrical wiring and hookup of your cooktop connected by a qualified electrician. After installation, have the electrician show you where your main cooktop disconnect is located. Wiring must conform to National Electrical Code. You can get a copy of the National Electrical Code, ANSI/ NFPA No. 70-Latest Edition, by writing to:

National Fire Protection Association Batterymarch Park Quincy, MA 02269

The cooktop conduit wiring is approved for copper wire connection only, and if you have aluminum house wiring, you must use special UL approved connectors for joining copper to aluminum. You must use a two-wire, three conductor 208/240 VAC, 60 Hertz electrical system. A white (neutral) wire is not needed for this unit. The cooktop must be installed in a circuit that does not exceed 125 VAC nominal to ground. Refer to the name plate on your cooktop for the KW rating for your cooktop.

Use the chart below to determine the minimum recommended dedicated circuit protection:

Name plate location

KW Rating 240v KW Rating 208V Recommended

Circuit Size (Dedicated)

20 Amp 4.9 KW - 7.2 KW 4.2 KW - 6.2 KW 30 Amp 7.3 KW - 9.6 KW 6.3 KW - 8.3 KW 40 Amp

9.7 KW - 12.0 KW 8.4 KW - 10.4 KW 50 Amp

31-11072-4 3

Installation Instructions PRE-INSTALLATION CHECKLIST

WARNING The electrical power to the cooktop supply line must be shut off while connections are being made. Failure to do so could result in serious injury or death. A When preparing cooktop opening, make sure

the inside of the cabinet and the cooktop do not interfere with each other. (See section on preparing the opening.)

B Remove packaging materials and literature package from the cooktop before beginning installation.

C Be sure to place all literature, Owners Manual, Installations, etc. in a safe place for future reference.

D Make sure you have all the tools and materials you need before starting the installation of the cooktop.

E Your home must provide the adequate electrical service needed to safely and properly use your cooktop. (Refer to section on electrical requirements.)

F When installing your cooktop in your home, make sure all local codes and ordinances are followed exactly as stated.

G Make sure the wall coverings, countertop and cabinets around the cooktop can withstand heat (up to 200F) generated by the cooktop.

H Installing cooktop in combination with other products.

Both products must be installed according to their specific product installation instructions. Consideration must be given the separate electrical requirements and locations:

Over one or two wall ovens: Only certain models may be installed over wall

ovens. The wall oven and cooktop will both have a label stating which models are approved in combination.

Over a Microwave: See microwave installation instructions for how

to install a microwave under a cooktop. For vertical dimension of cooktop, see Approximate Cooktop Dimensions section.

In combination with telescopic downdraft vent: See telescopic downdraft vent instructions for

how to install a vent behind a cooktop. The countertop must have a deep flat surface

to accommodate the combined installation of the cooktop and vent.

Over a warming drawer: See warming drawer instructions for how to

install a warming drawer under a cooktop. For vertical dimension of cooktop, see Approximate Cooktop Dimensions section.

ONHOT

Cooktop

Foam Packaging

Literature Package (Located under unit)

4 31-11072-4

Installation Instructions PREPARING THE OPENING

1 APPROXIMATE COOKTOP DIMENSIONS

2 CUTOUT DIMENSIONS OF THE COUNTERTOP

To ensure accuracy, it may be best to create a template when cutting the opening in the counter.

JXTR32 CUTOUT FILLER TRIM KIT (for use with 30 models): A filler trim kit is available for use if your countertop cutout is larger than the dimensions shown, up to 29-13/16 x 20-7/16. Order JXTR32B (black) or JXTR32W (white) to reduce the cutout opening for installation of this cooktop. This kit may be ordered from your dealer or directly from GE Appliances at www.geappliances.com.

28 1/2 - 28 5/8 (30) 33 7/8 - 34 (36)

length of cut

1-3/4 MIN. Between rear edge of cutout and the wall behind the cooktop.

19 5/8 - 19 3/4 (30) 19 1/8 - 19 1/4 (36)

width of cut

2-1/2 MIN. From front edge of cutout and front edge of countertop.

Size Models X Y Z Front Z Rear* 30 JP3030D, T

JP3530D, T 29 3/4 20 7/8 3 1/4 4

JP3030SJSS, JP3530SJSS

29 7/8 21 3 1/4 4

CP9530D, JP5030D, PP7030D, PP7030E, CEP7030

29 3/4 20 7/8 3 9/16 5 9/16

JP5030S, PP7030S, PP9030S, CEP90302

29 7/8 21 3 9/16 5 9/16

PP9030D, CEP90301 29 3/4 20 7/8 3 3/4 5 13/16 ZEU30RS 29 7/8 21 7/16 3 9/16 5 9/16

36 CP9536S, CEP7036 36 20 3/8 3 9/16 5 9/16 JP3036D, S, T JP3536D, S, T

36 1/8 20 7/16 3 9/16 4 1/16

JP5036D, S PP7036D, S

36 1/8 20 7/16 3 9/16 5 9/16

PP9036D, S, CEP9036

36 20 3/8 3 9/16 5 9/16

ZEU36RSJSS 36 1/8 20 7/8 3 9/16 5 9/16

* Depth at rear of cooktop at conduit location.

Cooktop

X

30 models: 19 1/4 36 models: 18 7/8

Z

Y

30 models: 28 1/16 36 models: 33 3/4

31-11072-4 5

Installation Instructions PREPARING THE OPENING (Cont)

3 MINIMUM CLEARANCES TO ADJACENT WALLS & CABINETS

If a 30 clearance between the cooktop and overhead combustible materials or metal cabinet cannot be maintained, then a minimum clearance of 24 is required and the underside of the cabinets above the cooktop must be protected with not less than 1/4 insulating millboard covered with sheet metal not less than 30 gage (0.0125) thick. A ventilation hood may be installed above the cooktop. See the ventilation hood installation instructions for the appropriate dimensions and clearances.

5 VERTICAL CLEARANCE Allow 5 minimum vertical clearance from the cooktop bottom (or 8-1/4 minimum depth from the countertop) to any combustible surfaces, such as a cabinet drawer.

4 Make sure the wall coverings, countertop and cabinets around the cooktop can withstand heat (up to 200F) generated by cooktop.

6 For Americans with Disabilities Act (ADA) Forward Approach Installation Only:

NOTE: The enclosure must be made of wood material. Also, an access panel is required for the junction box, hold-down brackets, and service.

Wall covering, cabinets and countertop must withstand heat up to 200F.

13 max. Depth of unprotected overhead cabinets

30 min. Clearance from countertop to unprotected overhead surface

30 min. for 30 cooktop 36 min. for 36 cooktop

2 min. Clearance from cutout to nearest vertical wall or cabinet on left side of the unit below the 15 MIN. clearance height.

15 min. Clearance from countertop to underside of

nearest cabinets on both sides of

cooktop, including any light rails.

1 1/2 min. (30) and 2 min. (36) Clearance from cutout to nearest vertical wall or cabinet

on right side of the unit below the 15 MIN.

clearance height. DRAWER

5" 8-1/4"

DRAWE

For models with no drop box, allow 5 minimum depth between the countertop and an enclosure. (JP3030, JP3530, JP3036, and JP3536)

For electronic touch and backlit knob models, allow 6-1/2 minimum depth between the countertop and an enclosure. (All other models)

5"

6 1/2"

Drop box

6 31-11072-4

Installation Instructions INSTALLING THE COOKTOP

1 VERTICAL CLEARANCE Install an approved junction box where it will be easily reached through the front of the cabinet where the cooktop will be located. The cooktop conduit is 4 feet long.

IMPORTANT: The junction box must be located where it will allow considerable slack in the conduit for serviceability.

3 ATTACH FOAM TAPE Apply the foam tape around the outer edge of the glass. Do not overlap the foam tape.

NOTE: On ZEU30 and ZEU36 models, apply the foam tape around the outer edge of the glass on the sides and rear of the unit only.

4 MOUNTING PARTS Remove the hold down brackets and screws from the literature package.

Screw the hold down bracket to the side of the cooktop unit. Repeat for opposite side of cooktop.2 PROTECT SURFACE OF COOKTOP

Place a towel or tablecloth onto the countertop. Lay the cooktop upside down onto the protected surface.

Install junction box so that it can be reached through the

front of the cabinet.

16 Min.

Bottom of Cooktop

Cloth under Cooktop

Bottom of Cooktop

Foam Tape

Cooktop Glass

Mounting Screw

Hold Down Bracket

Pre-Drilled HoleBottom of Cooktop

Cooktop Glass

Foam Tape

31-11072-4 7

Installation Instructions INSTALLING THE COOKTOP (Cont)

4 MOUNTING PARTS (Cont) Alternate Installation: You can order an alternate installation kit WB01X24570 with wing nuts and brackets by calling 800.GE.CARES. See diagram for instructions. Open the cabinet door. Install the second screw through the bracket and tighten. Then tighten the first screw. Install thumbscrew until it touches the bottom of the countertop.

IMPORTANT: Turn the thumbscrew until it touches the bottom of the countertop. Do not overtighten.

6 ELECTRICAL CONNECTIONS A When making the wire connections, use the entire

length of conduit provided. The conduit must not be shortened.

B With the cooktop in place, open the front of the cabinet door.

C Insert the wires from the conduit through the opening of the junction box.

D Connect the red and black leads from the cooktop conduit to the corresponding leads in the junction box. Connect the ground wire.

E Once the connections are made, secure wires together using wire nuts.

5 INSERT COOKTOP INTO CUTOUT Insert the cooktop centered into the cutout opening. Make sure the front edge of the countertop is parallel to the cooktop. Make final check that all required clearances are met.

Attach Hold Down Brackets to cabinet.

Cooktop Countertop

Hold Down Bracket

Cooktop

Strain Relief Clamp

Black

Red

Ground

Black

Red

Ground wire location

Strain Relief Clamp

Black

Red

Ground

8 31-11072-4

Installation Instructions INSTALLATIONELECTRICAL CONNECTIONS

CHECKLISTS

GROUNDING INSTRUCTIONS: The ground wire in the conduit is connected to the cooktop frame. Effective January 1, 1996, the National Electrical Code will not permit grounding through neutral. If used in new construction after January 1, 1996 or in a mobile home, recreational vehicle or if local codes do not permit grounding through the neutral white lead, attach the appliance grounding lead (green or copper) to the residence grounding conductor (green or bare copper) in accordance with local codes. When connecting to a 3

conductor branch circuit, if local codes permit, connect the ground connector lead of the cooktop to the branch circuit neutral (gray or white in color).

WARNING If the cooktop is being installed into a blind counter (one with no cabinet opening below), wire connections must be made before putting the cooktop into the cutout opening.

1 PRE-TEST CHECKLIST A Remove all protective film, if present, and any

stickers. B Check to be sure that all wiring is secure and not

pinched or in contact with moving parts. C Check level of appliance. D Check that the cooktop is properly grounded.

NOTE TO ELECTRICIAN: The power leads supplied with this appliance are UL recognized for connections to larger gauge household wiring. The insulation of these leads is rated at temperatures much higher than the temperature rating of household wiring. The current carrying capacity of a conductor is governed by the wire gauge and also the temperature rating of the insulation around the wire. NOTE: ALUMINUM WIRING

A. WARNING IMPROPER CONNECTION OF ALUMINUM HOUSE WIRING TO THE COPPER LEADS CAN RESULT IN AN ELECTRICAL HAZARD OR FIRE.

B. Splice copper wires to aluminum wiring using special connectors designed and UL approved for joining copper to aluminum, and follow the manufacturers recommended connector procedure closely.

NOTE: Wire used, location and enclosure of splices, etc., must conform to good wiring practice and local codes.

2 OPERATION CHECKLIST A Remove all items from the top of the cooktop

surface. B Turn on the power to the cooktop (refer to your

Owners Manual). Verify that all surface burners operate properly.

C Check that the circuit breaker is not tripped nor the house fuse blown.

D Check that conduit is securely connected to the junction box.

Instrucciones de instalacin

ANTES DE COMENZAR Lea estas instrucciones por completo y con cuidado.

IMPORTANTE Conserve estas instrucciones para el uso del inspector local.

IMPORTANTE Cumpla con todos los cdigos y reglas aplicables.

Nota para el instalador Asegrese de dejar estas instrucciones en poder del consumidor.

Nota para el consumidor Conserve estas instrucciones para referencias futuras.

El mal funcionamiento del producto debido a una instalacin incorrecta no est cubierto por la Garanta.

ADVERTENCIA Este aparato debe descargarse a tierra correctamente.

ATENCIN INSTALADOR TODAS LAS ESTUFAS DEBEN CONTAR CON

CABLEADO (CABLEADO DIRECTO) A UNA CAJA DE CONEXIONES APROBADA. ESTOS PRODUCTOS NO ACEPTAN ENCHUFES Y RECEPTCULOS.

La instalacin correcta es responsabilidad del instalador, y el mal funcionamiento del producto debido a una instalacin inadecuada NO est cubierto bajo la garanta.

NECESITAR LOS SIGUIENTES MATERIALES

HERRAMIENTAS QUE PUEDE NECESITAR

ABERTURA DE LA MESADA Si instalar la superficie de coccin en un material de superficie slida tal como granito, cuarzo o cualquier otra superficie slida natural o sinttica, le recomendamos que la abertura sea realizada por un instalador profesional de gabinetes o mesadas. Las aberturas de las superficies de coccin de mesadas de madera o laminados de madera podrn ser preparadas usando una sierra de vaivn y un taladro elctrico.

PARTES INCLUIDAS

31-11072-4 01-19 GEA

Tuercas para cablesCaja de conexiones

Sierra

Lpiz

Gafas de seguridad

Broca perforadora de 1/8 y taladro elctrico o manual

Regla o regla para nivelar

Destornillador Phillips

2 abrazaderas de montaje

4 Tornillos (WB01X1137)

Cinta de espuma WB06K5042

Conector de Presin a 90 o Recto para Conductos de 1

Estufa elctrica de 36 y 30 Radiante Excluye los Modelos de Flujo Descendente

Preguntas? Comunquese con nosotros al 1.800.432.273 o visita GEAppliances.com. En Canad, llame 1.800.561.3344 o visita GEAppliances.ca.

2 31-11072-4

Instrucciones de instalacin INSTRUCCIONES DE SEGURIDAD IMPORTANTES

PARA SU SEGURIDAD Para su seguridad personal, retire los fusibles de su

hogar o bien desconecte el cortacircuitos antes de comenzar con la instalacin. El no hacerlo puede resultar en lesiones serias o incluso la muerte.

Asegrese que su estufa sea instalada correctamente por un instalador o tcnico de servicio calificado.

Para eliminar el riesgo de quemaduras o incendio debido al contacto con los elementos de superficie calentados, debe evitarse el almacenaje en los gabinetes ubicados sobre los elementos de superficie. Si se cuenta con espacio en un gabinete, puede reducir el riesgo instalando una campana que se proyecte horizontalmente un mnimo de 5" ms del fondo de los gabinetes. La instalacin de gabinetes sobre la estufa no debe exceder 13" de profundidad.

Asegrese que los gabinetes y las cubiertas de las paredes alrededor de la estufa puedan soportar las temperaturas generadas por la estufa (hasta 200 F).

La estufa debe ser fcil de acceder y deber contar con iluminacin natural durante el da.

Siempre desconecte el servicio electrico que va hacia la estufa antes de reparar o dar servicio a la estufa. Esto puede hacerse desconectando el fusible o cortacircuitos. No hacer esto puede resultar en un shock elctrico peligroso o fatal. Sepa en dnde se localiza el interruptor principal de desconexin. Si no lo sabe, pdale a su electricista que le muestre la ubicacin.

REQUISITOS ELCTRICOS Este aparato debe contar con el voltaje y frecuencia adecuados, y deber conectarse a un circuito derivado individual debidamente descargado a tierra, protegido por un cortacircuitos o un fusible temporizado como lo indica la placa y el cuadro ms abajo. Le recomendamos que un electricista calificado conecte el cableado elctrico y conexin de su estufa. Despus de la instalacin, pdale al electricista que le muestre en dnde se localiza el interruptor principal de desconexin de su estufa. El cableado debe cumplir con el Cdigo Elctrico Nacional. Puede obtener una copia del Cdigo Elctrico Nacional, ANSI/NFPA No. 70-ltima edicin, escribiendo a:

Asociacin Nacional para la Prevencin de Incendios Batterymarch Park Quincy, MA 02269

El cableado conductor de la estufa est aprobado para conexiones nicamente con cables de cobre, y si cuenta con cableado de aluminio, debe usar conectores especiales aprobados por UL para unir cobre con aluminio. Debe usar un sistema elctrico con conductor de dos cables y tres conductores 208/240 VCA, de 60 Hertz. No se requiere un cable blanco (neutral) para esta unidad. La estufa debe instalarse en un circuito que no exceda 125 VCA nominales de descarga a tierra. Consulte el rtulo sobre su estufa para conocer la clasificacin en kilovatios de su estufa.

Use el siguiente cuadro para determinar la proteccin mnima recomendada para el circuito especializado:

Ubicacin del rtulo

Potencia en KW de 240V

Potencia en KW de 208V

Tamao de Circuito

Recomendado (Especializado)

20 Amp 4.9 KW - 7.2 KW 4.2 KW - 6.2 KW 30 Amp 7.3 KW - 9.6 KW 6.3 KW - 8.3 KW 40 Amp

9.7 KW - 12.0 KW 8.4 KW - 10.4 KW 50 Amp

31-11072-4 3

Instrucciones de instalacin LISTA DE VERIFICACIN PREVIA A LA INSTALACIN

ADVERTENCIA La corriente elctrica a la linea de abastecimiento de la estufa debe cortarse durante la realizacin de conexiones. El no hacerlo puede resultar en una lesin seria o la muerte.

A Cuando se prepare para la abertura de la estufa, asegrese que el interior del gabinete y la estufa no interfieran uno con el otro. (Consulte la seccin de preparacin de la abertura).

B Retire los materiales de empaque y el material impreso de la estufa antes de comenzar la instalacin.

C Asegrese de colocar todo el material impreso, Manual de propietario, Instalaciones, etc., en un lugar seguro para referencia futura.

D Asegrese de contar con todas las herramientas y materiales que necesita antes de comenzar la instalacin de la estufa.

E Su hogar debe contar con el servicio elctrico adecuado para el uso seguro y correcto de su estufa. (Consulte la seccin de requisitos elctricos).

F Cuando instale la estufa en su hogar, asegrese de cumplir todos los cdigos y reglas locales tal y como se establecen.

G Asegrese de que las cubiertas de las paredes, el mostrador y los gabinetes alrededor de la estufa puedan soportar las temperaturas generadas por la estufa (hasta 200 F).

H Instalacin de la superficie de coccin en combinacin con otros productos.

Ambos productos deben ser instalados de acuerdo con sus instrucciones de instalacin especficas del producto. Se deben tener en consideracin los requisitos y ubicaciones elctricas especficas:

Sobre uno o dos hornos de pared: Slo ciertos modelos pueden ser instalados

sobre los hornos de pared. El horno de pared y la superficie de coccin tendrn ambos una etiqueta que indique cules modelos estn aprobados para uso combinado.

Sobre el Microondas: Para instalar un microondas debajo de una

superficie de coccin, consulte las instrucciones de instalacin del horno microondas. Para conocer la dimensin vertical de la superficie de coccin, consulte la seccin de Dimensiones Aproximadas de la Superficie de Coccin.

En combinacin con la ventilacin telescpica descendente:

Para instalar una ventilacin detrs de la superficie de coccin, consulte las instrucciones de la ventilacin telescpica descendente.

La mesada debe contar con una superficie profunda y plana para ubicar la instalacin combinada de la superficie de coccin y la ventilacin.

Sobre un cajn para calentar: Para instalar un cajn para calentar debajo de una

superficie de coccin, consulte las instrucciones de instalacin del cajn para calentar. Para conocer la dimensin vertical de la superficie de coccin, consulte la seccin de Dimensiones Aproximadas de la Superficie de Coccin.

ONHOT

Estufa

Embalaje de gomaespuma

Paquete de material impreso (Ubicado debajo de la unidad)

4 31-11072-4

Instrucciones de instalacin PREPARACIN DE LA ABERTURA

1 DIMENSIONES GENERALES DE LA SUPERFICIE DE COCCIN

2 DIMENSIONES DEL REA CORTADA EN EL MOSTRADOR

Para asegurar la precisin, es mejor realizar una plantilla al cortar la abertura de la mesada.

JUEGO DE ACABADOS DE RELLENO DE CORTE JXTR32 (para uso con modelos de 30): Existe un juego de acabados de relleno disponible para el uso si el rea cortada del mostrador es mayor que las dimensiones mostradas, hasta 29-13/16 x 20-7/16. Ordene el JXTR32B (negro) o JXTR32W (blanco) para reducir el recorte de la abertura para la instalacin de esta superficie de coccin. Este kit puede ser ordenado a su vendedor minorista o directamente a GE Appliances en www.geappliances.com.

28 1/2 - 28 5/8 (30) 33 7/8 - 34 (36) longitud del corte

MNIMO de 1 entre el extremo trasero de la abertura y la pared detrs de la superficie de coccin.

19 5/8 - 19 3/4 (30) 19 1/8 - 19 1/4 (36)

ancho del corte

MNIMO de 2-1/2 desde el extremo frontal de la abertura y el extremo frontal de la mesada.

*Profundidad en la parte trasera de la superficie de coccin en la ubicacin del conducto.

Estufa

X

30 modelos: 19 1/4 36 modelos: 18 7/8

Z

Y

30 modelos: 28 1/16 36 modelos: 33 3/4

Tamao Modelos X Y Z Frente Z Parte Trasera*

30 JP3030D, T JP3530D, T

29 3/4 20 7/8 3 1/4 4

JP3030SJSS, JP3530SJSS

29 7/8 21 3 1/4 4

CP9530D, JP5030D, PP7030D, PP7030E, CEP7030

29 3/4 20 7/8 3 9/16 5 9/16

JP5030S, PP7030S, PP9030S, CEP90302

29 7/8 21 3 9/16 5 9/16

PP9030D, CEP90301 29 3/4 20 7/8 3 3/4 5 13/16 ZEU30RS 29 7/8 21 7/16 3 9/16 5 9/16

36 CP9536S, CEP7036 36 20 3/8 3 9/16 5 9/16 JP3036D, S, T JP3536D, S, T

36 1/8 20 7/16 3 9/16 4 1/16

JP5036D, S PP7036D, S

36 1/8 20 7/16 3 9/16 5 9/16

PP9036D, S, CEP9036

36 20 3/8 3 9/16 5 9/16

ZEU36RSJSS 36 1/8 20 7/8 3 9/16 5 9/16

31-11072-4 5

Instrucciones de instalacin

3 DESPEJES MNIMOS HASTA LAS PAREDES Y GABINETES ADYACENTES

Si no es posible mantener un despeje de 30 entre la superficie de coccin y los materiales combustibles o un gabinete metlico que se encuentren ms elevados, entonces se requerir un despeje mnimo de 24 y la parte inferior de los gabinetes que se encuentran por encima de la superficie de coccin debern ser protegidos con no menos de de cartulina aislante cubierta por una lmina metlica con un espesor no inferior a 30 (0.0125). Podr ser instalada una campana de ventilacin encima de la superficie de coccin. Para conocer las dimensiones y despejes adecuados, consulte las instrucciones de instalacin de la campana de ventilacin.

4 Asegrese que las cubiertas de las paredes, el mostrador y los gabinetes alrededor de la estufa puedan soportar las temperaturas generadas por la estufa (hasta 200 F).

La cubierta de la pared, los gabinetes y el mostrador deben soportar calor hasta 200 F.

Profundidad mxima de 13 de gabinetes elevados desprotegidos

Despeje mnimo de 30 desde la mesada hasta una superficie elevada desprotegida

Despeje mnimo de 2 desde la abertura hasta la pared vertical ms cercana o el gabinete del lado izquierdo de la unidad que est por debajo de una altura de despeje mnimo de 15.

Despeje mnimo de 15 desde la mesada hasta el lado inferior

de los gabinetes ms cercanos a ambos

lados de la superficie de coccin, incluyendo

cualquier riel de luz.

Despeje mnimo de 1 (30) y despeje mnimo de 2 (36) desde la abertura

hasta la pared vertical ms cercana o el gabinete del

lado derecho de la unidad que est por debajo de una

altura mnima de 15.

Mnimo de 30 para una superficie de coccin de 30 Mnimo de 36 para una superficie de coccin de 36

PREPARACIN DE LA ABERTURA (Cont)

5 ESPACIOS LIBRES VERTICALES Deje un espacio vertical de por lo menos 5 desde la parte inferior de la placa de coccin (o una profundidad mnima de 8-1/4 desde la mesada) hasta cualquier superficie combustible, tal como el cajn de un gabinete.

6 Instalacin Por Delante nicamente de Acuerdo con la Ley de Estadounidenses con Incapacidades (ADA)

NOTA: La cubierta deber estar hecha de material de madera. Adems, se requiere un panel de acceso para la caja de conexiones, los soportes de los costados, y el servicio tcnico.

DRAWER

5" 8-1/4"

CAJN

Con los modelos sin buzn, deje un espacio vertical de por lo menos 5 entre la mesada y la cubierta. (JP3030, JP3530, JP3036, y JP3536)

Si se trata de modelos con tecla electrnica tctil y perilla de luz trasera, deje una profundidad mnima de por lo menos 6 1/2 entre la mesada y la cubierta. (todos los dems modelos)

5"

6 1/2"

Drop box

6 31-11072-4

Instrucciones de instalacin INSTALACIN DE LA ESTUFA

1 INSTALACIN DE LA CAJA DE CONEXIONES

Instale una caja de conexiones aprobada en un lugar de fcil acceso a travs del frente del gabinete en donde pueda colocarse la estufa. El conducto de la estufa tiene 4 pies de longitud.

IMPORTANTE: La caja de conexiones debe localizarse en donde el conducto est lo suficientemente flojo para permitir que se le d servicio.

3 APLIQUE LA CINTA DE ESPUMA Aplique la cinta de espuma alrededor del borde externo del vidrio. No superponga la cinta de espuma.

NOTA: aplique la cinta de espuma alrededor del borde externo del vidrio en los lados y borde posterior de la unidad.

4 LAS PARTES DE MONTAJE Saque las abrazaderas de montaje y tornillos del empaque con material impreso.

Atornille la abrazadera de montaje a un lado de la unidad de la estufa. Repita en el lado opuesto de la estufa.2 PROTECCIN DE LA SUPERFICIE

DE LA ESTUFA Coloque una toalla o mantel sobre el mostrador. Coloque la estufa al revs sobre el rea protegida.

Instale la caja de conexiones de modo que pueda alcanzarse a travs

del frente del gabinete.

16 Mn.

Parte inferior de la estufa

Pao debajo de la estufa

Parte inferior de la estufa

Cinta de espuma

Vidrio de la estufa

Tornillo de montaje

Abrazadera de montaje

Agujero previamente perforadoParte inferior de la estufa

Vidrio de la estufa

Cinta de espuma

31-11072-4 7

Instrucciones de instalacin INSTALACIN DE LA ESTUFA (Cont)

4 LAS PARTES DE MONTAJE (Cont) Instalacin alternativa: Usted puede ordenar un kit de instalacin alternativa WB01X24570 con tuercas mariposa y soportes llamando al 800.GE.CARES. Para acceder a instrucciones, consulte el diagrama. Abra la puerta del gabinete. Instale el segundo tornillo a travs del soporte y ajuste. Luego ajuste el primer tornillo. Instale el tornillo de mariposa hasta que toque la parte inferior de la mesada.

IMPORTANTE: Gire el tornillo de mariposa hasta que toque la parte inferior de la mesada. No ajuste de ms.

6 CONEXIONES ELCTRICAS A Cuando realice las conexiones de cables, utilice toda la

extensin del conducto incluido. El conducto no debe reducirse.

B Con la estufa colocada en su lugar, abra el frente de la puerta del gabinete.

C Inserte los cables del conducto a travs de la abertura de la caja de conexiones.

D Conecte los cables rojo y negro del conductor de la estufa a los cables correspondientes en la caja de conexiones. Conecte el cable a tierra.

E Una vez que se hayan realizado las conexiones, fije los cables con las tuercas para cables.

5 INSERTE LA ESTUFA EN EL REA CORTADA

Inserte la estufa centrada en el rea cortada. Asegrese de que el borde frontal del mostrador est paralelo con respecto a la estufa. Asegrese de verificar al final que todos los espacios especificados hayan sido respetados.

Adhiera los Soportes al gabinete.

Anafe Mesada

Abrazadera de montaje

Estufa

Pinza de alivio de tensin

Negro

Rojo

Descarga a tierra

Negro

Rojo

Ubicacin del cable de descarga a tierra

Pinza de alivio de tensin

Negro

Rojo

Descarga a tierra

8 31-11072-4

Instrucciones de instalacin INSTALACINCONEXIONES ELCTRICAS

LISTAS DE VERIFICACIN

INSTRUCCIONES PARA DESCARGA A TIERRA: El cable de descarga a tierra en el conducto se conecta al armazn de la estufa. A partir del 1 de enero de 1996, el Cdigo Nacional sobre Electricidad no permitir la descarga a tierra a travs de cables neutrales. Si se usa en una construccin nueva despus del 1 de enero de 1996 o bien en una casa rodante, vehculo recreativo, o bien si los cdigos locales no permiten la descarga a tierra a travs de cables blancos neutrales, sujete el cable de descarga a tierra del aparato (verde o cobre) al conductor de descarga a tierra de la residencia (verde o cobre)

de acuerdo con los cdigos locales. Cuando conecte a un circuito derivado de 3 conductores, si lo permiten los cdigos locales, conecte el cable del conector de descarga a tierra al circuito derivado neutral (de color gris o blanco).

ADVERTENCIA Si la estufa se va a instalar en un mostrador sin salida (uno sin abertura del gabinete inferior), las conexiones del cableado debern realizarse antes de colocar la estufa en el rea cortada.

1 LISTA DE VERIFICACIN PREVIA A Retire toda la pelcula protectora, si la hay, y las

calcomanas.

B Verifique que todos los cables estn fijos y que no estn torcidos o en contacto con partes mviles.

C Verifique el nivel del aparato.

D Verifique que la estufa est descargada a tierra correctamente.

2 LISTA DE VERIFICACIN DE OPERACIN

A Retire todos los objetos que se encuentren sobre la superficie de la estufa.

A Encienda la toma de corriente de la estufa (consulte su Manual del propietario). Verifique que todas las hornillas de la superficie funcionen correctamente.

A Verifique que el cortacircuitos no est desactivado o que se haya fundido el fusible de su hogar.

A Verifique que el conducto est conectado correctamente a la caja de conexiones.

NOTA al electricista: Los alambres elctricos proporcionados con este aparato son reconocidos por la UL para conexiones cableado residencial de mayor calibre. El aislante de estos alambres supera las especificaciones indicadas para cableado residencial. La capacidad actual de conduccin del cable depende de la clasificacin de la temperatura del aislamiento alrededor del alambre. NOTA: Cableado de aluminio

A. ADVERTENCIA UNA CONEXIN INAPROPIADA DEL CABLEADO DEL ALUMINIO RESIDENCIAL CON EL COBRE, PODRA RESULTAR EN PROBLEMAS SERIOS O EN INCENDIO.

B. Conecte los alambres de cobre a los alambres de aluminio usando conectores especi

Manualsnet FAQs

If you want to find out how the JP3030TJWW GE works, you can view and download the GE JEP5036 JP3030TJWW Cooktop Installation Instructions on the Manualsnet website.

Yes, we have the Installation Instructions for GE JP3030TJWW as well as other GE manuals. All you need to do is to use our search bar and find the user manual that you are looking for.

The Installation Instructions should include all the details that are needed to use a GE JP3030TJWW. Full manuals and user guide PDFs can be downloaded from Manualsnet.com.

The best way to navigate the GE JEP5036 JP3030TJWW Cooktop Installation Instructions is by checking the Table of Contents at the top of the page where available. This allows you to navigate a manual by jumping to the section you are looking for.

This GE JEP5036 JP3030TJWW Cooktop Installation Instructions consists of sections like Table of Contents, to name a few. For easier navigation, use the Table of Contents in the upper left corner.

You can download GE JEP5036 JP3030TJWW Cooktop Installation Instructions free of charge simply by clicking the “download” button in the upper right corner of any manuals page. This feature allows you to download any manual in a couple of seconds and is generally in PDF format. You can also save a manual for later by adding it to your saved documents in the user profile.

To be able to print GE JEP5036 JP3030TJWW Cooktop Installation Instructions, simply download the document to your computer. Once downloaded, open the PDF file and print the GE JEP5036 JP3030TJWW Cooktop Installation Instructions as you would any other document. This can usually be achieved by clicking on “File” and then “Print” from the menu bar.