Frigidaire FGEH3047VF Installation Instructions PDF

1 of 16
1 of 16

Summary of Content for Frigidaire FGEH3047VF Installation Instructions PDF

1

INSTALLATION INSTRUCTIONS FRONT CONTROL FREESTANDING ELECTRIC RANGE

INSTALLATION AND SERVICE MUST BE PERFORMED BY A QUALIFIED INSTALLER.

IMPORTANT: SAVE FOR LOCAL ELECTRICAL INSPECTOR'S USE. READ AND SAVE THESE INSTRUCTIONS FOR FUTURE REFERENCE.

IMPORTANT SAFETY INSTRUCTIONS If the information in this manual is not followed

exactly, a fire or electrical shock may result causing property damage, personal injury or death.

Important Notes to the Installer: Read all instructions contained in these installation

instructions before installing range. Remove all packing material from the oven

compartments before connecting the gas & electrical supply to the range.

Observe all governing codes and ordinances. Be sure to leave these instructions with the

consumer.

Important Notes to the Consumer: Keep these instructions with your owners guide for future reference.

As when using any appliance generating heat, there are certain safety precautions you should follow. These are listed in the Use & Care Guide, read it carefully.

Be sure your range is installed and grounded properly by a qualified installer or service technician.

Make sure the wall coverings around the range can withstand the heat generated by the range.

To eliminate the need to reach over the surface elements, cabinet storage space above the elements should be avoided.

Tip Over Hazard

Range leveling leg

Anti-tip bracket

A child or adult can tip the range and be killed. Verify the anti-tip device has been installed to floor or wall.

Ensure the anti-tip device is re-engaged to floor or wall when the range is moved. Do not operate the range without the anti-tip device in place and engaged. Failure to follow these instructions can result in death or serious burns to children and adults.

To check if the anti-tip bracket is installed properly, use both arms to grasp the rear edge of the range back. Carefully attempt to tilt range forward. When properly installed, the range should not tilt forward.

Refer to the anti-tip bracket installation instructions supplied with your range for proper installation.

FOR YOUR SAFETY: Do not store or use gasoline or other flammable vapors and liquids in the vicinity of this or any other appliance.

United States

P/N 809127105 (1901) Rev. C English pages 1-8

Spanish - pages 9-16

2

30 ELECTRIC FRONT CONTROL FREESTANDING INSTALLATION INSTRUCTIONS

1. Clearances and Dimensions a. Provide adequate clearances between the range and adjacent combustible surfaces. b. LocationCheck location where the range will be installed. Check for proper electrical supply and the stability of floor. c. Dimensions that are shown must be used. Given dimensions provide minimum clearance. Contact surface must be

solid and level.

BACK VIEW

1 30 Minimum*

Minimum to wall on either side of range above 36 height.

36

18 Minimum to cabinets on either side of range

25 Max.

13 Maximum depth for cabinets above range top.

0 clearance below cooking top and at rear of range

Typical cabinet installationFront view

Side view

30 Minimum

30 Minimum

FRONT VIEW

Minimum to wall on either side of range above 36 (914 mm) height.

SIDE VIEW

1 (25 mm)

36 (914 mm)

30 (762 mm) Minimum

30 (762 mm)

18 (457 mm)

Minimum to cabinets on either side of range.

13 330 mm

Maximum depth for cabinets above range top.

0 (0 mm) clearance below cooking top and at rear of range.30 (762 mm)

RANGE OVERALL DIMENSIONS

30 (762 mm)

25- 3/4 (654 mm)

48 (1219 mm) Maximum

49 (1245 mm) Maximum

Door Open 29- 7/8

(759 mm)

36

1/8

Centerline of range

All dimensions for electrical outlet location are maximum.

Dashed cubed area shows where the electrical outlet must be

installed for flush to the wall installation.

25 635 mm

11 (279 mm) 22

(559 mm)

Wall Edge

2-5/8 (67 mm) for models equipped with warmer drawers

3-1/2 (89 mm) for models equipped with storage drawers

6 (152 mm)

(3 mm)(914 mm)

*30" (762 mm) MINIMUM CLEARANCE BETWEEN THE TOP OF THE COOKING SURFACE AND THE BOTTOM OF AN UNPROTECTED WOOD OR METAL CABINET; OR 24" (610 mm) MINIMUM WHEN BOTTOM OF WOOD OR METAL CABINET IS PROTECTED BY NOT LESS THAN 1/4" (6 mm) FLAME RETARDANT MILLBOARD COVERED WITH NOT LESS THAN NO. 28 MSG SHEET STEEL, 0.015" (0.4 mm) STAINLESS STEEL, 0.024" (0.6 mm) ALUMINUM OR 0.020" (0.5 mm) COPPER. 0" (0 mm) CLEARANCE IS THE MINIMUM FOR THE REAR OF THE RANGE. FOLLOW ALL DIMENSION REQUIREMENTS PROVIDED ABOVE TO PREVENT PROPERTY DAMAGE, POTENTIAL FIRE HAZARD, AND INCORRECT COUNTERTOP AND CABINET CUTS.

TO ELIMINATE THE RISK OF BURNS OR FIRE BY REACHING OVER HEATED SURFACE UNITS, CABINET STORAGE SPACE LOCATED ABOVE THE SURFACE UNITS SHOULD BE AVOIDED. IF CABINET STORAGE IS TO BE PROVIDED, THE RISK CAN BE REDUCED BY INSTALLING A RANGE HOOD THAT PROJECTS HORIZONTALLY A MINIMUM OF 5" (127 mm) BEYOND THE BOTTOM OF THE CABINETS.

29 7/8"

Maximum

36 5/8" 1/4"

26 6/8"

47"Door open Fig. 2

Fig. 1

Fig. 3

3

30 ELECTRIC FRONT CONTROL FREESTANDING INSTALLATION INSTRUCTIONS

2. Tools You Will Need

3. Anti-Tip Bracket Installation Instructions Important Safety Warning To reduce the risk of tipping of the range, the range should be secured to the floor by properly installed anti-tip bracket and screws packed with the range. Failure to install the anti-tip bracket will allow the range to tip over if excessive weight is placed on an open door or if a child climbs upon it. Serious injury might result from spilled hot liquids or from the range itself. If range is ever moved to a different location, the anti-tip brackets must also be moved and installed with the range. Instructions are provided for installation in wood or cement fastened to either the floor or wall. When installed to the wall, make sure that screws completely penetrate dry wall and are secured in wood or metal. When fastening to the floor or wall, be sure that screws do not penetrate electrical wiring or plumbing.

A. Locate the Bracket Using the Template - (Bracket may be located on either the left or right side of the range. Use the information below to locate the bracket if template is not available). Mark the floor or wall where left or right side of the range will be located. If rear of range is against the wall or no further than 1-1/4" (32 mm) from wall when installed, you may use the wall or floor mount method. If molding is installed and does not allow the bracket to fit flush against the wall, remove molding or mount bracket to the floor. For wall mount, locate the bracket by placing the back edge of the template against the rear wall and the side edge of template on the mark made referencing the side of the range. Place bracket on top of template and mark location of the screw holes in wall.

For leveling legs and Anti-Tip Bracket: Adjustable wrench or channel lock

pliers 5/16" Nutdriver or Flat Head

Screwdriver Electric Drill & 1/8" Diameter Drill Bit (Masonry Drill Bit if installing in concrete) Level & Measuring Tape For electrical supply connection: 1/4" & 3/8" Socket driver or Nutdriver Additional Materials You Will Need: Power Supply Cord or Copper Electrical Wiring & Metal

Conduit (for hard wiring)

If rear of range is further than 1-1/4" (32 mm) from the wall when installed, attach bracket to the floor. For floor mount, locate the bracket by placing back edge of the template where the rear of the range will be located. Mark the location of the screw holes, shown in template.

(32 mm)

(32 mm)

B. Drill Pilot Holes and Fasten Bracket - Drill a 1/8 (3 mm) pilot hole where screws are to be located. If bracket is to be mounted to the wall, drill pilot hole at an approximate 20 downward angle. If bracket is to be mounted to masonry or ceramic floors, drill a 5/32 (4 mm) pilot hole 1-3/4 (44 mm) deep. The screws provided may be used in wood or concrete material. Use a 5/16 (8 mm) nut- driver or flat head screwdriver to secure the bracket in place.

Fig. 4

Fig. 5

Fig. 6

4

30 ELECTRIC FRONT CONTROL FREESTANDING INSTALLATION INSTRUCTIONS

C. Level and Position Range - Level range by adjusting the (4) leveling legs with a wrench. Note: Aminimum clearance of 1/8 (3 mm) is required between the bottom of the range and the leveling leg to allow room for the bracket. Use a spirit level to check your adjustments. Slide range back into position. Visually check that rear leveling leg is inserted into and fully secured by the Anti-Tip Bracket by removing lower panel or storage drawer. For models with a warmer drawer or broiler compartment, grasp the top rear edge of the range and carefully attempt to tilt it forward.

4. Electrical Connection Requirements

Avoid fire hazard or electrical shock. Failure to follow this warning may casue serious injury, fire, or death.

This appliance must be properly installed and grounded by a qualified technician in accordance with the National Electrical Code ANSI/NFPA No. 70 -- latest edition -- and Local Electrical Code requirements.

This appliance may be connected by means of permanent wiring or power supply cord kit.

When installing permanent wiring, do not leave excess wire in range compartment. Excess wire in the range compartment may not allow the rear access cover to be replaced properly and could create a potential electrical hazard if wires become pinched. Connect only as instructed under Permanent Wire Connections in Step 5c. When using flexible conduit or range cable use flex connector or range cable strain relief

Models requiring power supply cord kit RISK OF FIRE OR ELECTRICAL SHOCK MAY OCCUR IF AN INCORRECT SIZE RANGE CORD KIT IS USED, THE INSTALLATION INSTRUCTIONS ARE NOT FOLLOWED OR STRAIN RELIEF BRACKET IS DISCARDED. This appliance may be connected by means of a power supply cord. Only a power supply cord kit rated at 125/250 volts minimum, and marked for use with ranges shall be used. See Fig. 10 for cord kit ampere rating information. Cord must have either three (3) or four (4) conductors (See Fig. 8). Terminals on end of wires must be either closed loop or open-end spade lugs with upturned ends. Cord must have strain relief properly installed. See Steps 5a. for 4-Wire or 4b. for 3-Wire connections.

NOTE: Range is shipped from factory with 1-3/8" dia. hole as shown. To use either 7/8" dia. hole or 1-1/8" dia. knockouts refer to Fig. 9.

Fig. 8

3 & 4 - Wire electrical wall Receptacle types & recommended mounting orientation on wall

Required for new and remodeled installations

4-Wire Wall receptacle (14-50R)

Allowed for existing installations

3 Wire Wall receptacle (10-50R)

Fig. 9

Rear Access Cover

5. Electrical Connection to the Range The Rear Access Cover must be removed (Fig 9). To remove, loosen center screw (one screw) and remove cover. The terminal block will then be accessible.

Fig. 7

(17 mm)

5

30 ELECTRIC FRONT CONTROL FREESTANDING INSTALLATION INSTRUCTIONS

Fig. 11

5A. POWER CORD CONNECTIONS (4-Wire Connection Instructions - Refer to Fig.12) Before wiring the range review the suggested power source location drawing in Fig. 3. If connecting to a 4-Wire electrical system (new branch-circuit or mobile home requires 4-Wire connection):

1. Follow the manufacturers installation instructions supplied with the strain relief and install (Also see Figs. 9, 10 & 11).

2. Insert the end connectors for Line 1, Line 2 and Neutral and tighten securely to the terminal block.

IMPORTANT NOTE: DO NOT LOOSEN the factory installed nut connections which secure the range wiring to the terminal block. Electrical failure or loss of electrical connection may occur if these 3 nuts are loosened or removed.

3. You must disconnect the ground strap. Remove the factory installed ground screw & plate to release the copper ground strap from the frame of the appliance. Cut and discard the copper ground strap & plate. KEEP the ground screw.

4. Connect the ground wire (Green) lead with the eyelet to the frame of the appliance with the ground screw using the same hole in the frame where the ground screw was originally installed (See Fig. 12).

5. Make sure all screws are tightened securely and replace the rear access cover (See Fig. 9).

Fig. 12

NOTE: Internal white wire not present on all models.

5B. POWER CORD CONNECTIONS (3-Wire Connection Instructions For existing installations ONLY - Refer to Fig. 13). 1. Follow the manufacturers installation instructions

supplied with the strain relief and install (Also see Figs. 9, 10 & 11).

2. Insert the end connectors for Line 1, Line 2 and Neutral and tighten securely to the terminal block (See Fig. 13).

IMPORTANT NOTE: DO NOT LOOSEN the factory installed nut connections which secure the range wiring to the terminal block. Electrical failure or loss of electrical connection may occur if these 3 nuts are loosened or removed.

3. Make sure all connections are tightened securely and replace the rear access cover (See Fig. 9).

NOTE: Internal white wire not present on all models.

Fig. 13

Fig. 10

6

30 ELECTRIC FRONT CONTROL FREESTANDING INSTALLATION INSTRUCTIONS

Grounding Instructions (3-Wire Connections only) A ground strap is installed on this range which connects the center terminal of the terminal block (Neutral) to the range chassis. The ground strap is connected to the range by the center, lowest screw (See Fig. 13). The ground strap must not be removed unless National, State or Local Codes do not permit use of a ground strap. NOTE: If the ground strap is removed for any reason, a separate ground wire must be connected to the separate ground screw attached to the range chassis and to an adequate ground source.

5C. 3 & 4-WIRE PERMANENT WIRE CONNECTIONS 3 - Wire Permanent Connection - follow Steps 1,2 & 5 below. 4 - Wire Permanent Connection - follow Steps 1 thru 5 below. Before wiring the range, review the suggested power source location drawings in Fig. 3. If connecting to a 4-Wire electrical system (new branch- circuit or mobile home requires 4-Wire connection):

1. (3 & 4 - Wire Permanent Connections) Follow the manufacturers installation instructions supplied with the strain relief and install.

2. (3 & 4 - Wire Permanent Connections) Strip insulation away from the ends of the permanent wiring for Line 1, Line 2, Neutral (also strip ground wire on 4-Wire Connections). Tighten all 3 wire leads to the terminal block (Follow wire locations shown in Fig. 14).

IMPORTANT NOTE: DO NOT LOOSEN the factory installed nut connections which secure the range wiring to the terminal block. Electrical failure or loss of electrical connection may occur if these 3 nuts are loosened or removed. NOTE: For 3-Wire Permanent Connections skip Steps 3 & 4 and continue with Step 5.

3. (4-Wire Permanent Connection ONLY) Disconnect the ground strap. Remove the factory installed ground screw & plate to release the factory installed copper ground strap from frame of the appliance. Cut and discard the copper strap from the terminal block. KEEP the ground screw, ground plate and go to Step 4.

4. (4-Wire Permanent Connection ONLY) Connect the ground wire lead (Green) to the frame of the appliance using the ground screw & plate as shown in Fig. 15. Be sure to install using the same hole in the frame where the ground screw was originally installed.

5. (3 & 4 - Wire Permanent Connections) Make sure all connections are tightened securely and replace the rear access cover (See Fig. 9).

Fig. 14

Fig. 15

NOTE: Non-terminated field wire compression connections must be set at approximately 22in./lbs. Always use 10 ga. wire or larger.

6. Carefully Slide Range Into Final Location Be sure to provide all the adequate clearances and dimensions shown in Figs. 1, 2 & 3 before moving appliance into final location. Carefully slide range into final position while inserting rear leveling leg into and FULLY ENGAGING THE ANTI-TIP BRACKET (See Fig. 7). Make sure the power cord folds into the remaining open floor area behind the range Warmer or storage drawer. Be sure to check the level of the range. NOTE: Non-terminated field wire compression connections must be set at 22 in./lbs. or greater. Always use 10 gauge wire or larger.

7

30 ELECTRIC FRONT CONTROL FREESTANDING INSTALLATION INSTRUCTIONS

Filler Trim Attachment Instructions: 1. Remove the 7 screws on the vent trim on the back.

Fig. 19 - Range with filler trim installed.

2. Place the filler trim over the back by lining up the 7 screw holes of the filler trim with the vent trim and tighten screws.

3. When filler trim is secured it will be flush with the top of the range.

7. Install filler trim kit Note: Installation of the filler trim kit is not required.

Disconnect electrical power to range before beginning installation. Before servicing any part of the appliance, make sure the appliance is off and the surfaces are cool. Attempting to service the appliance while hot may cause burns or other injury.

Fig. 16

Fig. 17

Fig. 18

8. Door Handle Mounting In- structions (some models) 1. Remove handles from carton and any other protective

packaging. 2. Position handle end caps over left and right pre-

installed shoulder bolts (A) that are fastened to the door, ensuring the holes for the set screws are facing down.

3. While holding handle firmly against door, loosely tighten right Allen set screw (B) with supplied Allen wrench until there is no gap between handle and door.

4. Still holding the handle firmly to the door, firmly tighten left Allen set screw (B) with supplied Allen wrench.

5. Return to the right Allen set screw (B) and firmly tighten with supplied Allen wrench.

All set screws should be tightened so the screw is below the surface of the handle. The handle should be drawn tight to the door with no gaps. The door handle may loosen over time or if it was installed improperly. If this happens, tighten the set screws on the handles.

NOTE

8

30 ELECTRIC FRONT CONTROL FREESTANDING INSTALLATION INSTRUCTIONS

10. Care, Cleaning and Maintenance Refer to the Use & Care Manual for cleaning instructions.

If removing the range is necessary for cleaning or maintenance, disconnect the electrical power supply. If the electrical supply is inaccessible, lift the unit slightly at the front and pull out away from the wall. Pull only as far as necessary to disconnect the electrical supply. Finish removing the unit for servicing and cleaning. Reinstall in reverse order making sure to level the range and check electrical connections. See pages 2 and 3 for proper anchoring instructions.

Some models have a cool-air intake vent on the rear of the appliance. Do not block or obstruct this vent.

9. Model and Serial Number Location The serial plate is located on the right-hand surface of the oven front frame at the storage or warmer drawer; or the lower panel area.

When ordering parts for or making inquires about your range, always be sure to include the model and serial numbers and a lot number or letter from the serial plate on your range.

Your serial plate also tells you the Kilowatt rating (power requirements) and Voltage ratings.

Serial plate is located on the lower right front frame of the appliance. Alternate location may be under cooktop.

Serial Plate Locations:

Before You Call for Service Read the "Before You Call" and operating instruction sections in your Use & Care Manual. It may save you time and expense. The list includes common occurrences that are not the result of defective workmanship or materials in this appliance.

Refer to the warranty in your Use & Care Manual for our toll-free service number and address. Please call or write if

Fig. 20

Fig. 21

9

INSTRUCCIONES DE INSTALACION LA ESTUFA ELECTRICA DE 30

LA INSTALACION Y EL SERVICIO DEBEN SER EFECTUADOS POR UN INSTALADOR CALIFICADO.

IMPORTANTE: CONSERVE ESTAS INSTRUCCIONES PARA USO DEL INSPECTOR LOCAL DE ELECTRICIDAD.

LEA Y CONSERVE ESTAS INSTRUCCIONES PARA REFERENCIA FUTURA.

INSTRUCCIONES IMPORTANTES DE SEGURIDAD Si no se sigue estrictamente la informacin de este manual, se puede producir un incendio o un choque elctrico que cause daos materiales, lesiones corporales o fatales.

Notas Importantes para el Instalador: Lea todas las instrucciones indicadas en estas

instrucciones de instalacin antes de instalar la estufa. Saque todo el material de empaque del compartimiento

del horno antes de conectar el suministro de gas y de electricidad a la estufa.

Observe todos los cdigos y reglamentos vigentes. Asegrese de dejar estas instrucciones con el usuario.

Aviso importante al consumidor: Mantenga estas instrucciones con su Gua de Uso y

Cuidado para referencia futura. Al igual que con cualquier electrodomstico que genere

calor, existen ciertas precauciones de seguridad que usted debe seguir. Tales precauciones se encuentran en la Gua de Uso y Cuidado, lala atentamente.

Asegrese de que la estufa est bien instalada y sea puesta a tierra en forma debida por un instalador calificado o un tcnico de servicio.

Asegrese de que el revestimiento de la pared alrededor de la estufa pueda resistir el calor generado por la estufa.

Para eliminar la necesidad de tener que pasar sobre los elementos, se recomienda no instalar armarios arriba los elementos de la cubierta de la estufa.

Riesgo de volcamiento

Un nio o adulto puede volcar la estufa y acabar muerto. Verifique que se haya instalado el dispositivo antivuelco en el piso o en la pared.

Asegrese de que el dispositivo antivuelco se haya reacoplado cuando mueva la estufa sobre el piso o a la pared. No utilice la estufa sin el dispositivo antivuelco instalado y acoplado. Si no se siguen estas instrucciones, se puede provocar la muerte o quemaduras graves en nios y adultos.

Tornillo nivelador de la estufa Soporte

antivuelco

Para verificar si el soporte antivuelco est instalado correctamente, sostenga el borde trasero de la parte trasera de la estufa usando ambos brazos. Intente inclinar la estufa hacia adelante con cuidado. Si est instalada correctamente, la estufa no debera inclinarse hacia adelante.

Consulte las instrucciones de instalacin del soporte antivuelco proporcionadas con la estufa para instalarlo adecuadamente.

WARNING:

PARA SU SEGURIDAD: No almacene ni use gasolina u otros vapores y lquidos inflamables cerca de este o cualquier otro electrodomstico.

Estados Unidos

P/N 809127105 (1901) Rev. C Ingls pginas 1-8

Espaol - pginas 9-16

10

INSTRUCCIONES DE INSTALACION PARA LA ESTUFA ELECTRICA DE 30

1. Espacios y dimensiones a. Proporcione espacios adecuados entre la estufa y las superficies combustibles adyacentes. b. UbicacinExamine el lugar en el cual va a ser instalada la estufa. Determine la existencia de suministro elctrico

adecuado y la estabilidad del piso. c. Se deben usar las medidas indicadas. Las dimensiones indicadas proporcionan espacio mnimo. La superficie de contacto

debe ser slida y estar a nivel

VISTA TRASERA

1 30 Minimum*

Minimum to wall on either side of range above 36 height.

36

18 Minimum to cabinets on either side of range

25 Max.

13 Maximum depth for cabinets above range top.

0 clearance below cooking top and at rear of range

Typical cabinet installationFront view

Side view

30 Minimum

30 Minimum

FRONT VIEW

Minimum to wall on either side of range above 36 (914 mm) height.

SIDE VIEW

1 (25 mm)

36 (914 mm)

30 (762 mm) Minimum

30 (762 mm)

18 (457 mm)

Minimum to cabinets on either side of range.

13 330 mm

Maximum depth for cabinets above range top.

0 (0 mm) clearance below cooking top and at rear of range.30 (762 mm)

RANGE OVERALL DIMENSIONS

30 (762 mm)

25- 3/4 (654 mm)

48 (1219 mm) Maximum

49 (1245 mm) Maximum

Door Open 29- 7/8

(759 mm)

36

1/8

Centerline of range

All dimensions for electrical outlet location are maximum.

Dashed cubed area shows where the electrical outlet must be

installed for flush to the wall installation.

25 635 mm

11 (279 mm) 22

(559 mm)

Wall Edge

2-5/8 (67 mm) for models equipped with warmer drawers

3-1/2 (89 mm) for models equipped with storage drawers

6 (152 mm)

(3 mm)(914 mm)

*ESPACIO LIBRE MINIMO DE 30 ENTRE LA CUBIERTA DE COCINAR DE LA ESTUFA Y LA PARTE INFERIOR DE UN ARMARIO DE METAL O DE MADERA NO PROTEGIDO; O 24 MINIMO CUANDO LA PARTE INFERIOR DE UN ARMARIO DE METAL O DE MADERA ESTA PROTEGIDA CON CARTON RETARDANTE A LAS LLAMAS DE NO MENOS DE 1/4 CUBIERTO CON CHAPA DE ACERO NO INFERIOR AL NO. 28 MSG, ACERO INOXIDABLE DE 0.015, ALUMINO DE 0.024 O COBRE DE 0.020. EL ESPACIO LIBRE DE 0 ES EL MINIMO PARA LA PARTE TRASERA DE LA ESTUFA. SIGA TODAS LAS DIMENSIONES INDICADAS

NTERIORMENTE PARA EVITAR DAOS MATERIALES, RIESGOS DE INCENDIO Y CORTES INCORRECTOS DE LOS ARMARIOS Y DE LAS MESADAS.

PARA ELIMINAR EL RIESGO DE QUEMADURAS O INCENDIOS AL PASAR SOBRE LOS ELEMENTOS CALIENTES, SE DEBE EVITAR COLOCAR ARMARIOS DE ALMACENAMIENTO SOBRE LA ESTUFA. SI SE INSTALAN ARMARIOS SOBRE LA ESTUFA, SE PUEDEN REDUCIR TALES RIESGOS INSTALANDO UNA CAMPANA EXTRACTORA QUE SE PROYECTE HORIZONTALMENTE UN MINIMO DE 5 MAS AFUERA DE LA PARTE INFERIOR DE LOS ARMARIOS.

29 7/8"

Maximum

36 5/8" 1/4"

26 6/8"

47"Door open Fig. 2

Fig. 1

Fig. 3

Vista frontal

Vista lateral

Instalacin tpica del gabinete

Mnimo a la pared en cualquier lado del rango por encima de 36 pul- gadas de altura

Mnimo para gabinetes a

da lado del rango

Profundidad mxima para gabinetes arriba del rango superior

0 pulgadas de espacio libre debajo de la parte su- perior de la cocina y en la parte trasera del estufa

Mximo

Puerta abierta

Todas las dimensiones para la ubicacin del tomacorriente son mximas.

El rea discontinua discontinua muestra dnde debe instalarse la toma de corri- ente para instalarla a nivel de la pared.

Borde de la pared

2-5 / 8 pulgadas (67 mm) para modelos i ados con c jones ms clidos

3-1 / 2 pulgadas (89 mm) para modelos equipados con cajones de almace-

namiento

11

INSTRUCCIONES DE INSTALACION PARA LA ESTUFA ELECTRICA DE 30

2. Herramientas que va a necesitar

3. Instruccin para la instalacin de las fijaciones de anti-inclinacin Nota importante de seguridad Para reducir el riesgo de inclinacin de la cocina, sta debe ser asegurada hacia el piso con las fijaciones de anti-inclinacin y los tornillos que vienen con la cocina. Si no instala las fijaciones, corre el riesgo que su cocina pueda inclinarse si pone demasiado peso sobre la puerta abierta o si un nio sube sobre sta. Esto podra ocasionar graves lesiones causadas por derrames de lquidos calientes o por la propria cocina.

Si la cocina es trasladada a otro lugar, las fijaciones de anti- inclinacin deben tambin ser trasladadas y instaladas con la cocina.

Las instrucciones provistas sirven para instalacin en suelo de madera o concreto. Al fijar los tornillos al suelo, asegurase que no atraviesen la instalacin elctrica o de fontanera.

A. Ubicacin del soporte utilizando la plantilla - (El soporte puede ser ubicado ya sea en el lado izquierdo o derecho de la estufa. Use la informacin indicada a continuacin para colocar el soporte si no se dispone de la plantilla. Marque el piso o la pared donde se colocar el costado izquierdo o derecho de la estufa. Si la parte trasera de la estufa ser colocada contra la pared o a no ms de 1-1/4 de la pared cuando ya est instalada, usted puede usar el mtodo de instalacin en el piso o en la pared. Si tiene moldura instalada y sta no permite que el soporte quede a ras contra la pared, retire la moldura o instale el soporte en el piso. Para el montaje en la pared, ubique la plantilla colocando el borde trasero de la plantilla contra la pared trasera y el borde lateral de la plantilla en la marca hecha indicando el costado de la estufa. Coloque el soporte sobre la plantilla y marque la ubicacin de los agujeros de los tornillos en la

Para patas de nivelacin y montura anti- vuelco Llave ajustable o alicates Llave para apretar tuercas de 5/16 o

un destornillador de cabeza plana Taladro elctrico y una broca de 1/8

(broca de taladro de hormign de 5/32 si se instala sobre hormign)

Nivel & Cinta de medicin Para la conexin del suministro elctrico: Llave de boca tubular o llave para

tuercas de 1/4 y 3/8 Materiales adicionales necesarios Cordn elctrico o Alambre elctrico

de cobre y conducto metlico (para alambrado permanente)

pared. Si la parte trasera de la estufa est a ms de 1-1/4 de la pared cuando ya est instalada, instale el soporte en el piso. Para el montaje en el piso, ubique el soporte colocando el borde trasero de la plantilla donde quedar ubicada la parte trasera de la estufa. Marque la ubicacin de los agujeros de los tornillos mostrados en la plantilla.

B. Taladre agujeros pilotos e instale el soporte - Taladre un agujero piloto de 1/8 donde se vayan a instalar los tornillos. Si el soporte va a ser instalado en la pared, taladre un agujero piloto en un ngulo descente de aproximadamente 20. Si el soporte va a ser instalado en pisos de mampostera o de cermica, taladre un agujero piloto de 5/32 y 1-3/4 (44 mm) de profundidad. Los tornillos provistos pueden ser usados en materiales de madera o concreto. Use una llave de tuerca de 5/16 (8 mm) o un destornillador de punta plana para asegurar el soporte en su lugar.

Fig. 4

Fig. 5

Fig. 6

Ms de 1 1/4" (3 cm)

SOPORTE DE FIJACIN (NICAMENTE PARA INSTALACIN EN EL PISO)

Pared

Instalacin en el piso

Pata niveladora

P ar

te

p o

st er

io r

d e

la e

st u

fa

Soporte antivuelco

SOPORTE DE FIJACIN (INSTALACIN EN LA PARED O EL PISO)

Pata niveladora

P ar

te

p o

st er

io r

d e

la e

st u

fa

1 1/4" (3 cm) mx.

Instalacin en la pared

Larguero

Soporte antivuelcoInstalacin en el piso

12

INSTRUCCIONES DE INSTALACION PARA LA ESTUFA ELECTRICA DE 30

C. Nivele y ubique la estufa - Nivele la estufa ajustando los cuatro (4) tornillos niveladores con una llave. Nota: Se debe dejar un espacio libre mnimo de 1/8 (3 mm) entre la parte inferior de la estufa y los tornillos niveladores a fin de dejar espacio para instalar el soporte. Use un nivel de burbuja de aire para verificar los ajustes. Deslice la estufa de nuevo a su lugar. Verifique visualmente si el tornillo nivelador trasero est insertado y firmemente asegurado por el soporte antivuelco retirando el panel inferior o la gaveta de almacenamiento. Para los modelos con una gaveta calentadora o compartimiento asador, sujete la estufa desde el borde superior trasero y trate de inclinarla hacia adelante cuidadosamente.

4. Requisitos de conexin elctrica

Evite peligro de incendio o descarga elctrica. El incumplimiento de esta advertencia puede causar lesiones graves, incendios o la muerte.

Este aparato debe estar instalado en forma apropiada y puesto a tierra por un tcnico calificado, de acuerdo con el National Electric Code (Cdigo Nacional de Electricidad) ANSI/NFPA No. 70 ltima edicin y con los requerimientos de electricidad de los cdigos locales.

Este aparato puede ser conectado por medio de una extensin a un tomacorriente local permanente o por medio de Juego de Cordn para el Suministro de Energa

Cuando instale un cableado permanente, no deje el exceso de cable en el compartimento de rango. El exceso de cable en el compartimiento de rango puede no permitir que la cubierta de acceso posterior sea reemplazada adecuadamente y podra crear un riesgo elctrico potencial si los cables se pellizcan. Conctelo nicamente como se indica en Conexiones de cableado permanente en el Paso 4c. Al usar un conducto flexible o cable de rango, use un conector flexible o un alivio de tensin del cable de rango.

Modelos que requieren Juego de Cordn para el Suministro de Energa EL RIESGO DE INCENDIO O DESCARGAS ELCTRICAS PUEDE OCURRIR SI SE UTILIZA UN KIT DE CABLE DE ALCANCE INCORRECTO, NO SE SIGUEN LAS INSTRUCCIONES DE INSTALACIN O SE DESCART EL SOPORTE DE ALIVIO. Este electrodomstico se puede conectar por medio de un cable de suministro de energa. Solo se usar un kit de cable de suministro de potencia con una clasificacin de 125/250 voltios como mnimo y marcado para su uso con rangos. Consulte la Fig. 10 para obtener informacin sobre la calificacin del amperaje del kit de cordones. El cable debe tener tres (3) o cuatro (4) conductores (consulte la Fig. 8). Los terminales en el extremo de los cables deben ser terminales de bucle cerrado o de extremo abierto con extremos hacia arriba. El cable debe tener un alivio de tensin instalado correctamente. Vea los pasos 4a. para 4-Wire o 4b. para conexiones de 3 hilos.

NOTA: El rango se enva de fbrica con orificio de 1-3 / 8 de dimetro, como se muestra. Para usar 7/8 de dimetro. orificios o orificios de 1-1 / 8 de dimetro se refieren a la Fig. 9.

Fig. 8

3 & 4 - Tipos de receptculos de pared elctrica de alambre orientacin de montaje recomendada en la pared

Requerido para nuevo y instalaciones remodeladas

Pared de 4 hilos receptculo(14-50R)

Permitido por instalaciones existentes

Pared de 3 hilos receptculo (10-50R)

Fig. 9

Posterior Acceso Cubrir

5. Conexion electrica a la estufa. Se debe retirar la cubierta de acceso trasera (Fig. 9). Para retirar, afloje el tornillo central (un tornillo) y retire la cubierta de acceso. As se puede tener acceso al tablero. de bornes.

Fig. 7

(17 mm) Des

lic e l

a

es tu

fa

hac ia

atr s

Lateral de la estufa

SOPORTE

ANTIVUELCO

13

INSTRUCCIONES DE INSTALACION PARA LA ESTUFA ELECTRICA DE 30

Sujetacable

Separe el sujetacable antes de la instalacin

Placa de montaje

Instale aqu el

sujetacable Fig. 11

Tabla del Tamao de la Abertura de Conexin de la Estufa

Informaci sobre la potencia nominal en amperios del Juego de Cable de Alimentacin. Ver la placa de serie en la estufa para los datos sobre la potencia nominal en kilovatios.

Ver la placa de serie en la estufa para la potencia nominal en kilovatios

120/240 Voltios 120/208 Voltios

Dimetro (pulg.) de la Abertura de Conexin de la

Estufa

Potencia Nominal del Juego de

cable Juego de cable

Cableado Permanente

1-3/8" 1-3/8"

1-1/8" 1-3/8"

40/50 Amp. 50 Amp.

8,8-16,5 KW 7,9-12,5 KW 16,6-22,5 KW 12,6-18,5 KW

5A. CONEXIONES DEL CORDON DE ALIMENTACION (Instrucciones para Conexin Tetrafilar - Consulte la Fig.12) Antes del cableado de la estufa, revise los dibujos de las ubicaciones sugeridas para la fuente de alimentacin en la Fig. 3. Si se va a conectar a un sistema elctrico tetrafilar (los circuitos de derivacin nuevos o las casas rodantes requieren conexin tetrafilar): 1. Siga las instrucciones de instalacin del fabricante

suministradas con el sujetacable e instale (Adems vea las Figs. 9, 10 y 11).

2. Inserte los conectores de extremo para la Lnea 1, Lnea 2 y Neutro y apriete firmemente en el tablero de bornes.

NOTA IMPORTANTE: NO AFLOJE las conexiones de tuerca instaladas en la fbrica que aseguran el cableado de la estufa en el tablero de bornes. Se puede producir una falla elctrica o prdida de la conexin elctrica si estas 3 tuercas son aflojadas o retiradas.

3. Usted debe desconectar la cinta de conexin a tierra. Retire el tornillo y placa de tierra instalada en la fbrica para soltar la cinta de conexin a tierra de cobre del marco del electrodomstico. CONSERVE el tornillo de tierra.

4. Conecte el alambre de puesta a tierra (Verde) con el ojal en el marco del electrodomstico con el tornillo de tierra usando el mismo agujero del marco donde estaba originalmente instalado el tornillo de tierra (Ver Fig. 12).

5. Asegrese de que todas las tuercas estn firmemente apretadas y vuelva a colocar la cubierta de acceso trasera (Ver Fig. 9).

Fig. 12 NOTA: El cable blanco interno no est presente en todos los modelos.

Conecte aqu el alambre de cobre verde aislado de puesta a tierra con el tornillo de tierra

NOTAS: Instale el buje sujetacable. El alambre central o blanco debe estar siempre instalado en el borne central del tablero de bornes.

Conecte Lnea 2 aqu

Conexin Tetrafilar

Conexiones instaladas en la fbrica (NO AFLOJAR)

Tablero de bornes

Conecte Lnea 1 aqu

Corte la cinta de conexin a tierra. Descarte la cinta y la placa de conexin a tierra

Conecte aqu el alambre neutro (blanco o central)

A LA

M B

R E

N E

G R

O

A LA

M B

R E

B LA

N C

O (N

E U

TR O

)

A LA

M B

R E

R O

JO

C able de

tierra verde

5B. CONEXIONES DEL CORDON DE ALIMENTACION (Instrucciones para conexin trifilar para instalaciones existentes SOLAMENTE - Consulte la Fig. 13) 1. Siga las instrucciones de instalacin del fabricante

suministradas con el sujetacable e instale (Adems vea las Figs. 9, 10 y 11).

2. Inserte los conectores de extremo para la Lnea 1, Lnea 2 y Neutro y apriete firmemente en el tablero de bornes (Vea Fig. 13).

NOTA IMPORTANTE: NO AFLOJE las conexiones de tuerca instaladas en la fbrica que aseguran el cableado de la estufa en el tablero de bornes. Se puede producir una falla elctrica o prdida de la conexin elctrica si estas 3 tuercas son aflojadas o retiradas.

3. Asegrese de que todas las conexiones estn firmemente apretadas y vuelva a colocar la cubierta de acceso trasera (Vea Fig. 9).

NOTAS: Cable blanco solo es usado en algunos modelos.

Fig. 13

Conecte Lnea 1 aqu

NOTAS: Instale el buje sujetacable. El alambre central o blanco debe estar siempre instalado en el borne central del tablero de bornes.

Conexin Trifilar

Tablero de bornes

Conecte Lnea 2 aqu

Conecte el alambre neutro (blanco o central)

A LA

M B

R E

R O

JO

(N E

U TR

O )

A LA

M B

R E

CINTA DE CONEXION A TIERRA

TORNILLO Y PLACA DE TIERRA

Conexiones instaladas en la fbrica (NO AFLOJAR)

A LA

M B

R E

N E

G R

O

Fig. 10

14

INSTRUCCIONES DE INSTALACION PARA LA ESTUFA ELECTRICA DE 30

Instrucciones para la Puesta a Tierra (para conexiones trifilares solamente) Esta estufa tiene instalada una cinta de conexin a tierra que conecta el borne central del tablero de bornes (neutro) al chasis de la estufa. La cinta de conexin a tierra est conectada a la estufa mediante el tornillo central ms inferior (Ver Fig. 13). La cinta de conexin de tierra no debe retirarse a menos que el cdigo nacional, estatal o local no permitan el uso de una cinta de conexin a tierra. NOTA: Si por cualquier motivo se retira la cinta de conexin a tierra, se debe conectar un alambre de tierra separado al tornillo de tierra instalado en el chasis de la estufa y a una tierra adecuada.

5C. CONEXIONES DEL CABLEADO PERMANENTE TRIFILAR Y TETRAFILAR 3 - Conexin trifilar permanente - siga los pasos 1, 2 y 5 incluidos a continuacin. 4 - Conexin tetrafilar permanente - siga los pasos 1 al 5 que se encuentran ms abajo. Antes del cableado de la estufa, examine los dibujos de la ubicacin sugerida para la fuente de alimentacin en la Fig. 3. Si est conectando a un sistema elctrico tetrafilar, (un circuito de derivacin nuevo o casa rodante requieren conexin tetrafilar): 1. (Conexiones permanentes trifilares y tetrafilares) Siga las

instrucciones de instalacin del fabricante suministradas con el sujetacable e instale.

2. (Conexiones permanentes trifilares y tetrafilares) Desforre el aislamiento de los extremos del cableado permanente para la Lnea 1, Lnea 2, Neutro (adems desforre el alambre de conexin a tierra en las conexiones tetrafilares). Apriete los 3 conductores hacia el tablero de bornes (Siga las ubicaciones de los alambres que se muestran en la Fig. 14).

NOTA IMPORTANTE: NO AFLOJE las conexiones de tuerca instaladas en la fbrica que aseguran el cableado de la estufa en el tablero de bornes. Se puede producir una falla elctrica o prdida de la conexin elctrica si estas 3 tuercas son aflojadas o retiradas. NOTA: Para las conexiones permanentes trifilares omita los Pasos 3 y 4 y contine con el Paso 5.

3. (Conexin permanente tetrafilar SOLAMENTE) Desconecte la cinta de conexin a tierra. Retire el tornillo y placa de tierra instalada en la fbrica para soltar la cinta de conexin a tierra de cobre del marco del electrodomstico. CONSERVE el tornillo de tierra, la placa de tierra y siga con el Paso 4.

4. (Conexin permanente tetrafilar SOLAMENTE) Conecte el alambre terminal de puesta a tierra (Verde) al marco del electrodomstico usando el tornillo y la placa de conexin a tierra, como se muestra en la Fig. 15. Asegrese de instalarlo usando el mismo agujero del marco donde estaba originalmente instalado el tornillo de tierra.

5. (Conexiones permanentes trifilares y tetrafilares) Asegrese de que todas las tuercas estn firmemente apretadas y vuelva a colocar la cubierta de acceso trasera (Ver Fig. 9).

Fig. 14

Fig. 15

NOTA: Los campos de la compresin de las conexiones de los cables no terminadas deben ser usadas utilizando un cable de 10 ga. o ms grande y ajustarlos a aproximadamente 22 libras por pulgadas.

6. DESLICE CON CUIDADO LA ESTUFA HASTA SU LUGAR DEFINITIVO Asegrese de proveer todos los espacios libres adecuados y las dimensiones mostradas en las Figs. 1, 2 y 3 en la Pgina 1 antes de mover la estufa a su lugar definitivo. Deslice cuidadosamente la estufa hacia la abertura del gabinete a la vez que inserta el tornillo nivelador trasero en el SOPORTE ANTIVUELCO VERFICANDO QUE QUEDE BIEN ENGANCHADO (Ver Fig. 7). Asegrese de que el cordn de alimentacin quede plegado en el resto del rea abierta del piso detrs de la gaveta de almacenamiento o gaveta calentadora de la estufa. Asegrese de verificar la nivelacin de la estufa. NOTA: Los campos de la compresin de las conexiones de los cables no terminadas deben ser usadas utilizando un cable de 10 ga. o ms grande y ajustarlos a aproximadamente 22 libras por pulgadas.

TORNILLO DE CONEXION A TIERRA

CINTA DE CONEXION DE TIERRA

APRIETE LOS 3 CABLES TERMINALES Tablero de bornes

PLACA DE CONEXION A TIERRA

Lnea 1 Lnea 2Neutro

Conexin permanente tetrafilar SOLAMENTE

Conexin permanente tetrafilar SOLAMENTE

PLACA DE CONEXION A TIERRA

TORNILLO DE CONEXION A

TIERRA

CABLE TERMINAL DE

CONEXION A TIERRA

TIERRA APROPIADA PARA CONEXION PERMANENTE TETRAFILAR

TIERRA

15

INSTRUCCIONES DE INSTALACION PARA LA ESTUFA ELECTRICA DE 30

7. Instalar kit de ajuste de relleno Nota: no es necesario instalar el kit de acabado de relleno.

Corte la alimentacin elctrica de la estufa entes de instalar. Antes de realizar cualquier operacin de servicio con el electrodomstico, asegrese de que est desconectado y que las superficies estn fras. Si intenta realizar una operacin de servicio con el electrodomstico caliente, puede sufrir quemaduras u otras lesiones.

Instrucciones de colocacin de la moldura: 1. Retire los 7 tornillos en el orificio de ventilacin en el rango

de vuelta.

2. Coloque el borde de relleno sobre la parte posterior alinean- do los 7 orificios de los tornillos del borde de relleno con el borde de ventilacin y apriete los tornillos.

3. Cuando el ajuste de relleno est asegurado, quedar al ras con la parte superior del rango.

Fig. 16

Fig. 17

Fig. 18

Fig. 19 - Cocina con moldura trasera instalada.

8. Instrucciones de montaje de las asas de puerta 1. Extraiga el asa de la caja y retire el envoltorio de proteccin. 2. Coloque los capuchones del asa sobre los pernos de tope

preinstalados izquierdo y derecho (A), fijados a la puerta, cerciorndose de que los orificios de los tornillos de presin quedan orientados hacia abajo.

3. Sostenga el asa con firmeza contra la puerta, apriete ligeramente el tornillo de presin Allen (B) del extremo derecho con la llave Allen suministrada hasta eliminar el espacio entre el asa y la puerta.

4. Siga sosteniendo el asa con firmeza contra la puerta, a la vez que aprieta con fuerza el tornillo de presin Allen (B) con la llave Allen suministrada.

5. Vuelva al tornillo de presin Allen (B) del extremo derecho y apritelo con fuerza con la llave Allen suministrada.

Todos los tornillos de presin deben apretarse de modo que el tornillo quede por debajo de la superficie del asa. Las asas deben quedar perfectamente fijadas a la puerta sin dejar espacios. Es posible que el asa pierda firmeza con el tiempo o si se instala de manera incorrecta. Si esto sucede, apriete los tornillos de presin de las asas.

NOTA

16

INSTRUCCIONES DE INSTALACION PARA LA ESTUFA ELECTRICA DE 30

8. Cuidado, limpieza y mantenimiento Consulte el Manual de uso y cuidado para las instrucciones de limpieza.

Si es necesario retirar el rango para la limpieza o el mantenimiento, desconecte el suministro de energa elctrica. Si el suministro elctrico es inaccesible, levante la unidad ligeramente hacia adelante y retrese de la pared. Tire solo hasta donde sea necesario para desconectar el suministro elctrico. Termine de quitar la unidad para dar servicio y limpiarla. Vuelva a instalar en orden inverso asegurndose de nivelar el rango y verificar las conexiones elctricas. Consulte las pginas 2 y 3 para obtener instrucciones de anclaje adecuadas.

Algunos modelos tienen un respiradero de admisin de aire fro en la parte posterior del aparato. No bloquee u obstruya esta ventilacin.

7. Ubicacin del modelo y nmero de serie La placa de serie est ubicada en la superficie derecha del marco frontal del horno en el cajn de almacenamiento o calentador; o el rea del panel inferior.

Cuando ordene piezas o pregunte acerca de su rango, siempre asegrese de incluir los nmeros de modelo y de serie y un nmero de lote o letra de la placa de serie en su rango.

Su placa de serie tambin le indica la clasificacin de kilovatios (requisitos de potencia) y las clasificaciones de voltaje.

La placa de serie est ubicada en el marco frontal inferior derecho del dispositivo. La ubicacin alternativa puede ser debajo de la estufa.

Ubicaciones de placas de serie:

Antes de llamar al servicio Lea las secciones Antes de llamar y la instruccin de operacin en su Manual de uso y cuidado. Puede ahorrarle tiempo y dinero. La lista incluye las ocurrencias comunes que no son el resultado de mano de obra o materiales defectuosos en este electrodomstico.

Consulte la garanta en su Manual de uso y

Manualsnet FAQs

If you want to find out how the FGEH3047VF Frigidaire works, you can view and download the Frigidaire FGEH3047VF Installation Instructions on the Manualsnet website.

Yes, we have the Installation Instructions for Frigidaire FGEH3047VF as well as other Frigidaire manuals. All you need to do is to use our search bar and find the user manual that you are looking for.

The Installation Instructions should include all the details that are needed to use a Frigidaire FGEH3047VF. Full manuals and user guide PDFs can be downloaded from Manualsnet.com.

The best way to navigate the Frigidaire FGEH3047VF Installation Instructions is by checking the Table of Contents at the top of the page where available. This allows you to navigate a manual by jumping to the section you are looking for.

This Frigidaire FGEH3047VF Installation Instructions consists of sections like Table of Contents, to name a few. For easier navigation, use the Table of Contents in the upper left corner.

You can download Frigidaire FGEH3047VF Installation Instructions free of charge simply by clicking the “download” button in the upper right corner of any manuals page. This feature allows you to download any manual in a couple of seconds and is generally in PDF format. You can also save a manual for later by adding it to your saved documents in the user profile.

To be able to print Frigidaire FGEH3047VF Installation Instructions, simply download the document to your computer. Once downloaded, open the PDF file and print the Frigidaire FGEH3047VF Installation Instructions as you would any other document. This can usually be achieved by clicking on “File” and then “Print” from the menu bar.