Frigidaire FPBM3077RF Installation Instructions PDF

1 of 29
1 of 29

Summary of Content for Frigidaire FPBM3077RF Installation Instructions PDF

READ CAREFULLY.

KEEP THESE INSTRUCTIONS.

Installation Over the Range Instructions Microwave Oven

Read these instructions completely and carefully.

IMPORTANT Save these instructions for local inspectors use.

IMPORTANT Observe all governing codes and ordinances.

Note to Installer Be sure to leave these instructions with the Consumer.

BEFORE YOU BEGIN Note to Consumer Keep these

instructions for future reference. Skill level Installation of this appliance requires

basic mechanical and electrical skills. Proper installation is the responsibility of the installer. Product failure due to improper installation is not

covered under the Warranty.

p/n 316495163

orQuestions? Call 1-877-435-3287(US) 1-800-265-8352(Canada)

August 2015

Before You Use Your Microwave

CONTENTS

General information

Important Safety Instructions .................................. 3

Electrical Requirements .......................................... 3

Damage Shipment/Installation.............................. 4

Parts Included.......................................................... 4

Tools You Will Need ................................................ 5

Mounting Space ...................................................... 5

Step-by-step installation guide

68

Removing the Mounting Plate ...................... 6

Finding the Wall Studs .................................. 6

Determining Wall Plate Location .................. 7

Aligning the Wall Plate ................................ 8

Outside Top Exhaust

Attach Mounting Plate to Wall............12

Preparation of Top Cabinet................13

Checking for Proper Damper

Adapting Microwave Blower

A

B

C

Installation Instructions

21

20

20Recirculating ........................................

Mount the Microwave Oven ................19

Preparation of Top Cabinet ................17

Attach Mounting Plate to Wall ............17

Outside Back Exhaust ..........................16

Connecting Ductwork..........................15

Adjust the Exhaust Adaptor ................15

Operation ............................................14

Outside Back Exhaust ............................ 1619

Adapting Microwave Blower for Outside top Exhaust .......... 1314........

Placement of The Mounting Plate ......................

............................ 1215

Preparing Rear Wall for

Remove Blower Plate ...................... 16...... ..

Charcoal Filter Installing or Change the

22

Preparation of Top Cabinet ................21

Check Blower Plate ............................

.......................... 23

....................................22

Attach Mounting Plate to Wall ............

22

Installation Types............................................... 922

for Outside Back Exhaust................17 18

Mount the Microwave Oven ..........21

Hood Exhaust .................................................. 10 11

Mount the Microwave Oven ..........14 15

.......................... 24Template Information...................

EN-2

This product requires a three-prong grounded outlet. The installer must perform a ground continuity check on the power outlet box before beginning the installation to ensure that the outlet box is properly grounded. If not properly grounded, or if the outlet box does not meet electrical requirements noted (under ELECTRICAL REQUIREMENTS), a qualified electrician should be employed to correct any deficiencies.

CAUTION: For personal safety, remove house fuse or open circuit breaker before beginning installation to avoid severe or fatal shock injury.

CAUTION: For personal safety, the mounting surface must be capable of supporting the cabinet load, in addition to the added weight of this 6385 pound (28.538.5 kg) product, plus additional oven loads of up to 50 pounds (22.7 kg) or a total weight of 113135 pounds (51.361.2 kg).

CAUTION: For personal safety, this product cannot be installed in cabinet arrangements such as an island or a peninsula. It must be mounted to BOTH a top cabinet AND a wall.

NOTE: For easier installation and personal safety, it is recommended that two people install this product. IMPORTANT PLEASE READ CAREFULLY. FOR PERSONAL SAFETY, THIS APPLIANCE MUST BE PROPERLY GROUNDED TO AVOID SEVERE OR FATAL SHOCK.

The power cord of this appliance is equipped with a three-prong (grounding) plug which mates with a standard three-prong (grounding) wall receptacle to minimize the possibility of electric shock hazard from this appliance.

You should have the wall receptacle and circuit checked by a qualified electrician to make sure the receptacle is properly grounded.

Where a standard two-prong wall receptacle is encountered, it is very important to have it replaced with a properly grounded three-prong wall receptacle, installed by a qualified electrician.

DO NOT, UNDER ANY CIRCUMSTANCES, CUT, DEFORM OR REMOVE ANY OF THE PRONGS FROM THE POWER CORD. DO NOT USE WITH AN EXTENSION CORD.

IMPORTANT SAFETY INSTRUCTIONS

ELECTRICAL REQUIREMENTS Product rating is 120 volts AC, 60 Hertz, 15 amps and 1.6 kilowatts. This product must be connected to a

Ensure proper ground exists before use

Installation Instructions

EN-3

The power supply cord and plug should be brought to a the prevailing local code for this kilowatt rating. the requirements of the National Electrical Code or voltage and frequency. Wire size must conform to seperate and dedicated supply circuit of the proper

seperate and dedicated 15- to 20- ampere branch

National Electrical Code or the prevailing local code. by a qualifed electrician and conform to the The outler box and supply circuit should be installed be located in the cabinet above the microwave oven. circuit single grounded outlet. The outlet box should

PART QUANTITY

Wood Screws 2 (14 x 2)

Toggle Bolts (and wing nuts) (316 x 3)

Self-Aligning Machine 3 Screws (14-28 x 314)

Nylon Grommet (for metal cabinets)

1

If the unit is damaged in shipment, return the unit to the store in which it was bought for repair or replacement.

If the unit is damaged by the customer, repair or replacement is the responsibility of the customer.

If the unit is damaged by the installer (if other than the customer), repair or replacement must be made by arrangement between customer and installer.

DAMAGESHIPMENT/ INSTALLATION

Installation Instructions

PARTS INCLUDED

You will find the installation hardware contained in a packet with the unit. Check to make sure you have all these parts. NOTE: Some extra parts are included.

HARDWARE PACKET

PART QUANTITY

Template 1

Template

Installation 1Instructions

2Filters

PARTS INCLUDED (CONT.)

INSTALLATIONINSTRUCTIONS

ADDITIONAL PARTS

1adaptor

Grease

Exhaust

Glass 1Tray

1 Ring

T ru ntable

CabinetTop

Rear Wall

2

1

1

Shelf 1

USE & CARE MANUAL

Use & Care Manual

Convection wire rack

EN-4

2

For some models

For some models

TOOLS YOU WILL NEED

# 1 Phillips screwdriver Pencil

Ruler or tape measure and straight edge

Carpenter square (optional)

Tin snips (for cutting damper, if required)

Electric drill with 316, 12 and 58 drill bits

Hammer (optional)Stud finder or

Filler blocks or scrap wood pieces, if needed for top cabinet spacing (used on recessed bottom cabinet installations only)

Gloves

Saw (saber, hole or keyhole)

Level Duct and masking tape

Installation Instructions

Scissors (to cut template, if necessary)

Safety goggles

MOUNTING SPACE NOTES: The space between the cabinets must be

30 (76.2 cm)wide and free of obstructions. If you are going to vent your microwave oven

to the outside, see Hood Exhaust Section for exhaust duct preparation.

When installing the microwave oven beneath smooth, flat cabinets, be careful to follow the instructions on the top cabinet template for power cord clearance. As a guide to installation, see page 24 for Mounting Template Information.

CabinetCabinet

If the cabinet depth including the cabinet doors is more than 13'"" ' then the unit must be spaced out from wall using adequate materials supporting

150 Ibs to allow proper top vent air exhaust/intake.

Bottom Edge of Cabinet Needs to be 30 (76.2 cm) or More from the Cooking Surface

Backsplash

66 (167.6 cm) or More from the Floor to the Top of the Microwave

30 (76.2 cm)

2 (5.1 cm)

30 (76.2 cm)

min.

1 1

2 (4

m )

13 Maximum (33 cm) 7

4.6c

EN-5

PLACEMENT OF THE MOUNTING PLATE1

Installation Instructions

Find the studs, using one of the following methods: A. Stud finder a magnetic device which

locates nails. B. Use a hammer to tap lightly across the

mounting surface to find a solid sound. This will indicate a stud location.

After locating the stud(s), find the center by probing the wall with a small nail to find the edges of the stud. Then place a mark halfway between the edges. The center of any adjacent studs should be 16 (40.6 cm) or 24 (61 cm) from this mark. Draw a line down the center of the studs.

THE MICROWAVE MUST BE CONNECTED TO AT LEAST ONE WALL STUD.

1

Fold back all 4 carton flaps fully against carton sides. Then carefully roll the oven and carton over onto the top side. The oven should be resting in the Styrofoam.

REMOVING THE MICROWAVE OVEN FROM THE CARTON/ REMOVING THE MOUNTING PLATE

FINDING THE WALL STUDSB.

A.

2

Wall Studs

Center

3

Carton

Pull the carton up and off the oven.

2

Styrofoam

3

1

Screws Screws

Mounting Plate

5

4 Cut the middle of the outer protective plastic bag to remove the ounting latem p

Turntable glass tray

Exhaust AdapterSmall Hardware Bag

Glass Tray

Shelf

Remove the installation instructions,use and care, exhaust adapter, turntable ring, shelf , glass tray and the small hardware bag. Do not remove the Styrofoam protecting the front of the oven.

where they were removed.

Remove the screws from each end of the mounting plate. This plate will be used as the rear wall template and for mounting. Reinstall the screws into the holes

Ring below

EN-6

DETERMINING WALL PLATE LOCATION UNDER YOUR CABINETC.

Installation Instructions

Plate position flat bottom cabinet

Draw a line on the back wall equal to the depth of the front overhang.

to Cooktop C

3/8" TO EDGE

NOTE: IT IS VERY IMPORTANT TO

READ AND FOLLOW THE DIRECTIONS

IN THE INSTALLATION INSTRUCTIONS

BEFORE PROCEEDING WITH THIS

REAR WALL TEMPLATE. This Rear Wall Template serves to position the bottom

mounting plate and to locate the horizontal exhaust

outlet. 1. Use a level to check that the template is positioned

accurately. 2. Locate and mark at least one stud on the left or

right side of the centerline. It is important to use at least one wood

screw mounted firmly in a stud to support the weight

of the microwave. Mark two additional, evenly spaced

locations for the supplied toggle bolts.

3. Drill holes in the marked locations. Where there is

a stud, drill a 3/16" hole for wood screws. For holes

that do not line up with a stud, drill 5/8" holes for

toggle bolts. DO NOT INSTALL THE MOUNTING PLATE

AT THIS TIME. 4. Remove the template from the rear wall.

5. Review the Installation Instruction book for your

installation situation.

Locate and mark holes to align with holes in the

mounting plate. IMPORTANT: LOCATE AT LEAST ONE STUD ON EITHER SIDE OF

THE CENTERLINE. MARK THE LOCATION FOR 2 ADDITIONAL, EVENLY

SPACED TOGGLE BOLTS IN THE MOUNTING PLATE

AREA.

Locate and mark holes to align with holes in the

mounting plate. IMPORTANT: LOCATE AT LEAST ONE STUD ON EITHER SIDE OF

THE CENTERLINE. MARK THE LOCATION FOR 2 ADDITIONAL, EVENLY

SPACED TOGGLE BOLTS IN THE MOUNTING PLATE

AREA.

Trim the rear wall template along the dotted line.

Trim the rear wall template along the dotted line.

12"

4"

Darle vuelta a la hoja para consultar la

versin en Espaol.

CL

3/8" TO EDGE

NOTE: IT IS VERY IMPORTANT TO

READ AND FOLLOW THE DIRECTIONS

IN THE INSTALLATION INSTRUCTIONS

BEFORE PROCEEDING WITH THIS

REAR WALL TEMPLATE. This Rear Wall Template serves to position the bottom

mounting plate and to locate the horizontal exhaust

outlet. 1. Use a level to check that the template is positioned

accurately. 2. Locate and mark at least one stud on the left or

right side of the centerline. It is important to use at least one wood

screw mounted firmly in a stud to support the weight

of the microwave. Mark two additional, evenly spaced

locations for the supplied toggle bolts.

3. Drill holes in the marked locations. Where there is

a stud, drill a 3/16" hole for wood screws. For holes

that do not line up with a stud, drill 5/8" holes for

toggle bolts. DO NOT INSTALL THE MOUNTING PLATE

AT THIS TIME. 4. Remove the template from the rear wall.

5. Review the Installation Instruction book for your

installation situation.

Locate and mark holes to align with holes in the

mounting plate. IMPORTANT: LOCATE AT LEAST ONE STUD ON EITHER SIDE OF

THE CENTERLINE. MARK THE LOCATION FOR 2 ADDITIONAL, EVENLY

SPACED TOGGLE BOLTS IN THE MOUNTING PLATE

AREA.

Locate and mark holes to align with holes in the

mounting plate. IMPORTANT: LOCATE AT LEAST ONE STUD ON EITHER SIDE OF

THE CENTERLINE. MARK THE LOCATION FOR 2 ADDITIONAL, EVENLY

SPACED TOGGLE BOLTS IN THE MOUNTING PLATE

AREA.

Trim the rear wall template along the dotted line.

Trim the rear wall template along the dotted line.

12"

4"

Darle vuelta a la hoja para consultar la

versin en Espaol.

At least 30

C

3/8" TO EDGE

NOTE: IT IS VERY IMPORTANT TO

READ AND FOLLOW THE DIRECTIONS

IN THE INSTALLATION INSTRUCTIONS

BEFORE PROCEEDING WITH THIS

REAR WALL TEMPLATE. This Rear Wall Template serves to position the bottom

mounting plate and to locate the horizontal exhaust

outlet. 1. Use a level to check that the template is positioned

accurately. 2. Locate and mark at least one stud on the left or

right side of the centerline. It is important to use at least one wood

screw mounted firmly in a stud to support the weight

of the microwave. Mark two additional, evenly spaced

locations for the supplied toggle bolts.

3. Drill holes in the marked locations. Where there is

a stud, drill a 3/16" hole for wood screws. For holes

that do not line up with a stud, drill 5/8" holes for

toggle bolts. DO NOT INSTALL THE MOUNTING PLATE

AT THIS TIME. 4. Remove the template from the rear wall.

5. Review the Installation Instruction book for your

installation situation.

Locate and mark holes to align with holes in the

mounting plate. IMPORTANT: LOCATE AT LEAST ONE STUD ON EITHER SIDE OF

THE CENTERLINE. MARK THE LOCATION FOR 2 ADDITIONAL, EVENLY

SPACED TOGGLE BOLTS IN THE MOUNTING PLATE

AREA.

Locate and mark holes to align with holes in the

mounting plate. IMPORTANT: LOCATE AT LEAST ONE STUD ON EITHER SIDE OF

THE CENTERLINE. MARK THE LOCATION FOR 2 ADDITIONAL, EVENLY

SPACED TOGGLE BOLTS IN THE MOUNTING PLATE

AREA.

Trim the rear wall template along the dotted line.

Trim the rear wall template along the dotted line.

12"

4"

Darle vuelta a la hoja para consultar la

versin en Espaol.

Your cabinets may have decorative trim that interferes with the microwave installation. Remove the decorative trim to install the microwave properly and to make it level.

THE MICROWAVE MUST BE LEVEL. Use a level to make sure the cabinet bottom is level. If the cabinets have a front overhang only, with no back or side frame, install the mounting plate down the same distance as the front overhang depth. This will keep the microwave level.

Measure the inside depth of the front overhang.

Draw a horizontal line on the back wall an equal distance below the cabinet bottom as the inside depth of the front overhang.

For this type of installation with front overhang only, align the mounting tabs with this horizontal line, not touching the cabinet bottom as described in Step D.

Draw a vertical line on the wall at the center of the 30 wide space. Tape the Rear Wall Template onto the wall matching the centerline and touching the bottom of the cabinet.

to Cooktop

Draw a vertical line on the wall at the center of the 30 space. Tape the Rear Wall Template onto the wall matching the centerline and touching the bottom

C

3/8" TO EDGE

NOTE: IT IS VERY IMPORTANT TO

READ AND FOLLOW THE DIRECTIONS

IN THE INSTALLATION INSTRUCTIONS

BEFORE PROCEEDING WITH THIS

REAR WALL TEMPLATE. This Rear Wall Template serves to position the bottom

mounting plate and to locate the horizontal exhaust

outlet. 1. Use a level to check that the template is positioned

accurately. 2. Locate and mark at least one stud on the left or

right side of the centerline. It is important to use at least one wood

screw mounted firmly in a stud to support the weight

of the microwave. Mark two additional, evenly spaced

locations for the supplied toggle bolts. 3. Drill holes in the marked locations. Where there is

a stud, drill a 3/16" hole for wood screws. For holes

that do not line up with a stud, drill 5/8" holes for

toggle bolts. DO NOT INSTALL THE MOUNTING PLATE

AT THIS TIME. 4. Remove the template from the rear wall.

5. Review the Installation Instruction book for your

installation situation.

Locate and mark holes to align with holes in the

mounting plate. IMPORTANT: LOCATE AT LEAST ONE STUD ON EITHER SIDE OF

THE CENTERLINE. MARK THE LOCATION FOR 2 ADDITIONAL, EVENLY

SPACED TOGGLE BOLTS IN THE MOUNTING PLATE

AREA.

Locate and mark holes to align with holes in the

mounting plate. IMPORTANT: LOCATE AT LEAST ONE STUD ON EITHER SIDE OF

THE CENTERLINE. MARK THE LOCATION FOR 2 ADDITIONAL, EVENLY

SPACED TOGGLE BOLTS IN THE MOUNTING PLATE

AREA.

Trim the rear wall template along the dotted line.

Trim the rear wall template along the dotted line.

12"

4"

Darle vuelta a la hoja para consultar la

versin en Espaol.

cabinet bottom

Plate position framed recessed

1

3

2

300030

cabinet frame.

300030

17-1/ 2

-beneath -beneath

with front overhang Plate position bottom

-beneath recessed cabinet

EN-7

Installation Instructions

ALIGNING THE WALL PLATED.

CAUTION: Wear gloves to avoid cutting fingers on sharp edges.

Area E Hole A

Hole B Centerline notches Draw a Vertical Line

on Wall from Center of Top Cabinet

Draw a horizontal line on wall at the bottom of Rear Wall Template.

Horizontal LineHorizontal Line

CL

3/8" TO EDGE

NOTE: IT IS VERY IMPORTANT TO READ AND FOLLOW THE DIRECTIONS IN THE INSTALLATION INSTRUCTIONS BEFORE PROCEEDING WITH THIS REAR WALL TEMPLATE. This Rear Wall Template serves to position the bottom mounting plate and to locate the horizontal exhaust outlet. 1. Use a level to check that the template is positioned accurately. 2. Locate and mark at least one stud on the left or right side of the centerline.

It is important to use at least one wood screw mounted firmly in a stud to support the weight of the microwave. Mark two additional, evenly spaced locations for the supplied toggle bolts. 3. Drill holes in the marked locations. Where there is a stud, drill a 3/16" hole for wood screws. For holes that do not line up with a stud, drill 5/8" holes for toggle bolts.

DO NOT INSTALL THE MOUNTING PLATE AT THIS TIME. 4. Remove the template from the rear wall. 5. Review the Installation Instruction book for your installation situation.

Locate and mark holes to align with holes in the mounting plate. IMPORTANT: LOCATE AT LEAST ONE STUD ON EITHER SIDE OF THE CENTERLINE. MARK THE LOCATION FOR 2 ADDITIONAL, EVENLY SPACED TOGGLE BOLTS IN THE MOUNTING PLATE AREA.

Locate and mark holes to align with holes in the mounting plate. IMPORTANT: LOCATE AT LEAST ONE STUD ON EITHER SIDE OF THE CENTERLINE. MARK THE LOCATION FOR 2 ADDITIONAL, EVENLY SPACED TOGGLE BOLTS IN THE MOUNTING PLATE AREA.

Trim the rear wall template along the dotted line. 12"

4"

Darle vuelta a la hoja para consultar la versin en Espaol.

Draw a vertical line on the wall at the center of the 30" wide space.

NOTE: DO NOT MOUNT THE PLATE AT THIS TIME.

NOTE: Holes A and B are inside area E. If neither of

important to have at least one wood screw mounted firmly in a stud to support the weight of the microwave. Set the mounting plate aside.

1

2 Draw a horizontal line on the wall at the bottom of Rear Wall Template.

Holes A and B are not in a stud, find a stud somewhere in area E and draw a circle to line up with the stud. It is

3 Find a wall stud in area "E" of mounting plate Refer to section 1B. Finding the wall studs. For attaching the mounting plate into stud drill a 3/16" hole into wood stud. Drill a 5/8" hole for toggle bolt in 1 other location (Hole A or Hole B)

4

EN-8

A

INSTALLATION TYPES This microwave oven is designed for adaptation to the following three types of ventilation: A. Outside Top Exhaust (Vertical Duct) B. Outside Back Exhaust (Horizontal Duct) C. Recirculating (Non-Vented Ductless)

proceed to that section.

OUTSIDE TOP EXHAUST (VERTICAL DUCT)

OUTSIDE BACK EXHAUST (HORIZONTAL DUCT)

RECIRCULATING (NON-VENTED DUCTLESS)

See page 12

recirculating exhaust.

disposable charcoal filter installed to help remove smoke and odors.

Adaptor in Place for Outside Top Exhaust

2

B

C

Adaptor Must Be Moved to the Back for Outside Back Exhaust

NOTE: This microwave is shipped assembled for Recirculating. Select the type of ventilation required

(Choose A, B or C)

for your installation and

See page 16

See page 20

Models are shipped for

Some models have a

Installation Instructions

NOTE: Read the next two pages only if you plan to vent your exhaust to the outside. If you plan to recirculate the air back into the room, proceed to page 20.

EN-9

EQUIVALENT NUMBER EQUIVALENT

DUCT PIECES LENGTH x USED = LENGTH

Rectangular-to-Round 5 Ft. (1.5 m) x ( ) = Ft. or m Transition Adaptor*

Wall Cap 40 Ft. (12.2 m) x ( ) = Ft. or m

90 Elbow 10 Ft. (3 m) x ( ) = Ft. or m

45 Elbow 5 Ft. (1.5 m) x ( ) = Ft. or m

90 Elbow 25 Ft. (7.6 m) x ( ) = Ft. or m

45 Elbow 5 Ft. (1.5 m) x ( ) = Ft. or m

Roof Cap 24 Ft. (7.3 m) x ( ) = Ft. or m

Straight Duct 6 (15.2 cm) 1 Ft. (0.3 m) x ( ) = Ft. or m Round or 314 x 10 (8.2 x 25.4 cm Rectangular)

Total Ductwork = Ft. or m

Equivalent lengths of duct pieces are based on actual tests and reflect requirements for good venting performance with any vent hood.

* IMPORTANT: If a rectangular-to-round transition adaptor is used, the bottom corners of the damper will have to be cut to fit, using the tin snips, in order to allow free movement of the damper.

NOTE: If you need to install ducts, note that the total duct length of 314 x 10 (8.2 x 25.4 cm) rectangular or

(15.2 cm) diameter round duct

Outside ventilation requires an EXTERNAL EXHAUST

NOTE: It is important that venting be installed using the most direct route and with as few elbows as possible. This ensures clear venting of exhaust and helps prevent blockages. Also, make sure dampers swing freely and nothing is blocking the ducts.

Exhaust connection: The exhaust adaptor has been designed to mate with a standard 314 x 10 (8.2 x 25.4 cm) rectangular duct. If a round duct is required, a rectangular-to-round

Maximum duct length: For satisfactory air movement, the total duct length of 314 x 10 (8.2 x 25.4 cm) rectangular or

6 (15.2 cm) diameter round duct should not exceed 120 equivalentfeet (36.5 m).

Elbows, transitions, wall and roof caps, etc., present additional resistance to airflow and are equivalent to a section of straight duct which is longer than their actual physical size. When calculating the total duct length, add the equivalent lengths of all transitions and adaptors plus the length of all straight duct sections. The chart below shows you how to calculate total equivalent ductwork length using the approximate feet of equivalent length of some typical ducts.

Installation Instructions

INSTALLATION INSTRUCTIONS FOR EXTERNAL EXHAUST DUCTING

DUCT.Read the following carefully.

(12.5 should not exceed 120 equivalent feet (36.5 m).

diameter/ 6 (12.5 diameter/

7 cm)7 cm)

transition adaptor must be used. diameter duct is acceptable to use.

" A 5"""' ' ' ' ' " (12.7cm)/ 6" (15.2cm)

EN-10

EQUIVALENT NUMBER EQUIVALENT

DUCT PIECES LENGTH x USED = LENGTH

Roof Cap 24 Ft. (7.3 m) x (1) = 24 Ft. (7.3 m)

12 Ft. (3.6 m) Straight Duct 12 Ft. (3.6 m) x (1) = 12 Ft. (3.6 m) (6/15.2 cm Round)

Rectangular-to-Round 5 Ft. (1.5 m) x (1) = 5 Ft. (1.5 m) Transition Adaptor*

Equivalent lengths of duct pieces are based on actual tests and reflect requirements for good venting performance with any vent hood.

Total Length = 41 Ft. (12.5 m)

The following chart describes an example of one possible ductwork installation.

OUTSIDE TOP EXHAUST (EXAMPLE ONLY)

NOTE: For back exhaust, care should be taken to align exhaust with space between studs, or wall should be prepared at the time it is constructed by leaving enough space between the wall studs to accommodate exhaust.

* IMPORTANT: If a rectangular-to-round transition adaptor is used, the bottom corners of the damper will have to be cut to fit, using the tin snips, in order to allow free movement of the damper.

The following chart describes an example of one possible ductwork installation.

Installation Instructions

OUTSIDE BACK EXHAUST (EXAMPLE ONLY)

EQUIVALENT NUMBER EQUIVALENT

DUCT PIECES LENGTH* x USED = LENGTH

Wall Cap 40 Ft. (12.2 m) x (1) = 40 Ft. (12.2 m)

3 Ft. Straight Duct 3 Ft. (0.9 m) x (1) = 3 Ft. (0.9 m) (314 x 10/8.2 x 25.4 cm Rectangular)

90 Elbow 10 Ft. (3 m) x (2) = 20 Ft. (3 m)

Equivalent lengths of duct pieces are based on actual tests and reflect requirements for good venting performance with any vent hood.

Total Length = 63 Ft. (19.2 m)

EXTERNAL EXHAUST DUCTING

EN-11

Place the mounting plate against the wall and insert the toggle wings into the holes in the wall to mount the plate.

NOTE: Before tightening toggle bolts and wood screw, make sure the bottom of the mounting plate touch the bottom of the cabinet when pushed flush against the wall and that the plate is properly centered under the cabinet. CAUTION: Be careful to avoid pinching fingers between the back of the mounting plate and the wall.

Tighten all bolts. Pull the plate away from the wall to help tighten the bolts.

3

4

ATTACH THE MOUNTING PLATE TO THE WALL

A1.

Attach the plate to the wall using toggle bolts. At least one wood screw must be used to attach the plate to a wall stud.

Remove the toggle wings from the bolts.

Insert the bolts into the mounting plate through the holes designated to go into drywall and reattach the toggle wings to 34 (19 mm) onto each bolt.

1

INSTALLATION OVERVIEW A1. Attach Mounting Plate to Wall A2. Prepare Top Cabinet

Mount Microwave OvenA5. Adjust Exhaust AdaptorA6.

Wall

Mounting Plate

Spacing for Toggles More Than Wall Thickness

Bolt End

Toggle Bolt

Toggle Wings

To use toggle bolts:

Installation Instructions

2

OUTSIDE TOP EXHAUST (Vertical Duct)A

IMPORTANT NOTES: Make sure the screws for the

blower motor and blower plate are securely tightened when they are reinstalled. This will help to prevent excessive vibration.

Make sure the motor wiring has been properly routed and secured, and that the wires are not pinched.

A7. Connect Ductwork

A3.

A4. Check Damper Operation

Adapting Microwave Blower for Outside Top Exhaust

EN-12

3/8" TO EDGE

NOTE: IT IS VERY IMPORTANT TO

READ AND FOLLOW THE DIRECTIONS

IN THE INSTALLATION INSTRUCTIONS

BEFORE PROCEEDING WITH THIS

REAR WALL TEMPLATE.

This Rear Wall Template serves to position the bottom

mounting plate and to locate the horizontal exhaust

outlet. 1. Use a level to check that the template is positioned

accurately. 2. Locate and mark at least one stud on the left or

right side of the centerline.

It is important to use at least one wood

screw mounted firmly in a stud to support the weight

of the microwave. Mark two additional, evenly spaced

locations for the supplied toggle bolts.

3. Drill holes in the marked locations. Where there is

a stud, drill a 3/16" hole for wood screws. For holes

that do not line up with a stud, drill 5/8" holes for

toggle bolts. DO NOT INSTALL THE MOUNTING PLATE

AT THIS TIME.

4. Remove the template from the rear wall.

5. Review the Installation Instruction book for your

installation situation.

Locate and mark holes to align with holes in the

mounting plate.

IMPORTANT:

LOCATE AT LEAST ONE STUD ON EITHER SIDE OF

THE CENTERLINE.

MARK THE LOCATION FOR 2 ADDITIONAL, EVENLY

SPACED TOGGLE BOLTS IN THE MOUNTING PLATE

AREA. Locate and mark holes to align with holes in the

mounting plate.

IMPORTANT:

LOCATE AT LEAST ONE STUD ON EITHER SIDE OF

THE CENTERLINE.

MARK THE LOCATION FOR 2 ADDITIONAL, EVENLY

SPACED TOGGLE BOLTS IN THE MOUNTING PLATE

AREA. Trim the rear wall template along the dotted line.

Trim the rear wall template along the dotted line.

12"

4"

Darle vuelta a la hoja para consultar la

versin en Espaol.

IMPORTANT :Do not remove the cardboard spacers between the heat shield and door.

USE TOP CABINET TEMPLATE FOR PREPARATION OF TOP CABINET

You need to drill holes for the top support screws, a hole large enough for the power cord to fit through, and a cutout large enough for the exhaust adaptor.

A2.

Read the instructions on the TOP CABINET TEMPLATE.

Tape it underneath the top cabinet. Drill the holes, following the instructions on the

TOP CABINET TEMPLATE.

CAUTION: Wear safety goggles when drilling holes in the cabinet bottom.

Installation Instructions

A3.

Remove the screw that holds the blower plate to the microwave. Remove and save the screw holding the blower motor to the microwave.

Blower Plate

Blower Motor Screw

Back of Microwave

2

End B

End A

Carefully pull out the blower unit. The wires will extend far enough to allow you to adjust the blower unit.

1

ADAPTING MICROWAVE BLOWER FOR OUTSIDE TOP EXHAUST

Roll the blower unit 90 so that fan blade

microwave.

3

Back of Microwave

Before Rotation After Rotation

Back of Microwave

Back of Microwave

openings are facing out thetopof the

Back of Microwave

AFTER: Fan Blade

Place the blower unit back into the opening.

Openings Facing Top

CAUTION: Do not pull or stretch the blower unit wiring. Make sure the wires are not pinched, and that they are properly secured.

4

with the top of the unit facing up. Place the microwave in its upright position,

EN-13

3

MOUNT THE MICROWAVE OVEN

FOR EASIER INSTALLATION AND PERSONAL SAFETY, WE RECOMMEND THAT TWO PEOPLE INSTALL THIS MICROWAVE OVEN.

NOTE: If your cabinet is metal, use the nylon grommet around the power cord hole to prevent cutting of the cord. NOTE: We recommend using filler blocks if the cabinet front hangs below the cabinet bottom shelf.

IMPORTANT: If filler blocks are not used, case damage may occur from overtightening screws.

Insert a self-aligning screw through top center cabinet hole. Temporarily secure the oven by turning the screw at least two full turns after the threads have engaged. (It will be completely tightened later.) Be sure to keep power cord tight. Be careful not to pinch the cord, especially when mounting flush to bottom of cabinet.

2 Rotate front of oven up against cabinet bottom.

NOTE: When mounting the microwave oven, thread power cord through hole in bottom of top cabinet. Keep it tight throughout Steps 13. Do not pinch cord or lift oven by pulling cord.

Lift microwave, tilt it forward, and hook slots at back bottom edge onto four lower tabs of mounting plate.

1

CHECK FOR PROPER DAMPER OPERATION

Exhaust AdaptorBlower Plate

Damper

Back of Microwave

Make sure tape securing damper is removed and damper pivots easily before mounting microwave.

You will need to make adjustments to assure proper alignment with your house exhaust duct after the microwave is installed.

A3. ADAPTING MICROWAVE BLOWER FOR OUTSIDE TOP EXHAUST

Secure blower unit to microwave with the screw5 removed in Step 1. Make sure the screw is tight.

Replace blower plate with the screw removed in Step 1. Make sure the screw is tight.

Back of Microwave

6

7

Back of Microwave

Guide

Adaptor

Locking Tab

damper swings freely.

Attach the exhaust adaptor to the top of the blower plate by sliding it into the guides of the blower plate.

Push in securely until it is in the locking tabs. Take care to assure that the damper hinge is installed so thatthe

A4.

A5.

Installation Instructions

EN-14

IMPORTANT: Do not grip or use the handle or heat shield during installation. Do not remove the cardboard spacers between the heat shield and door.

4 Attach the microwave oven to the top cabinet.

7

Cabinet Front

Cabinet Bottom Shelf

Tighten the outer two screws to the top of the microwave oven. (While tightening screws, hold the microwave oven in place against the wall and the top cabinet.)

Filler Block

Microwave Oven Top

Equivalent to Depth of Cabinet Recess

Insert 2 self-aligning screws through outer top cabinet holes. Turn two full turns on each screw.

Installation Instructions

ADJUST THE EXHAUST ADAPTOR

Open the top cabinet and adjust the exhaust adaptor to connect to the house duct.

Back of Microwave

For Front-to-Back or Side-to-Side Adjustment, Slide the Exhaust Adaptor as Needed

Blower Plate Damper

Self-Aligning Screw

5

MOUNT THE MICROWAVE OVEN (cont.)

A6.A5.

CONNECTING DUCTWORK

1

2

Extend the house duct down to connect to the exhaust adaptor.

A7.

furnanceSeal exhaust duct joints using duct tape for high temperature applications.

House Duct

Tighten center screw completely.

EN-15

6

8 Install grease filters. See the Owners Manual packed with the microwave. IMPORTANT: Remove the cardhoard spacers between

heat shield and door.

INSTALLATION OVERVIEW B1. Prepare Rear Wall

B3. Attach Mounting Plate to Wall B4. Prepare Top Cabinet B5. Adjust Blower B6. Mount the Microwave Oven

IMPORTANT NOTES: Make sure the screws for the

blower motor and blower plate are securely tightened when they are reinstalled. This will help to prevent excessive vibration.

been properly routed and secured, and that the wires are not pinched.

Remove and save the screw that holds the blower plate to the microwave. Lift off the blower plate.

Back of Microwave

Installation Instructions

PREPARING THE REAR WALL FOR OUTSIDE BACK EXHAUST

B1.

You need to cut an opening in the rear wall for outside exhaust.

Read the instructions on the REAR WALL TEMPLATE.

Tape it to the rear wall. Cut the opening, following the instructions of the

REAR WALL TEMPLATE.

B2.

OUTSIDE BACK EXHAUST (Horizontal Duct)B

Blower Plate

REMOVE BLOWER PLATE

B2. Remove Blower Plate

3/8" TO EDGE

NOTE: IT IS VERY IMPORTANT TO

READ AND FOLLOW THE DIRECTIONS

IN THE INSTALLATION INSTRUCTIONS

BEFORE PROCEEDING WITH THIS

REAR WALL TEMPLATE. This Rear Wall Template serves to position the bottom

mounting plate and to locate the horizontal exhaust

outlet. 1. Use a level to check that the template is positioned

accurately. 2. Locate and mark at least one stud on the left or

right side of the centerline. It is important to use at least one wood

screw mounted firmly in a stud to support the weight

of the microwave. Mark two additional, evenly spaced

locations for the supplied toggle bolts.

3. Drill holes in the marked locations. Where there is

a stud, drill a 3/16" hole for wood screws. For holes

that do not line up with a stud, drill 5/8" holes for

toggle bolts. DO NOT INSTALL THE MOUNTING PLATE

AT THIS TIME. 4. Remove the template from the rear wall.

5. Review the Installation Instruction book for your

installation situation.

Locate and mark holes to align with holes in the

mounting plate. IMPORTANT: LOCATE AT LEAST ONE STUD ON EITHER SIDE OF

THE CENTERLINE. MARK THE LOCATION FOR 2 ADDITIONAL, EVENLY

SPACED TOGGLE BOLTS IN THE MOUNTING PLATE

AREA.

Locate and mark holes to align with holes in the

mounting plate. IMPORTANT: LOCATE AT LEAST ONE STUD ON EITHER SIDE OF

THE CENTERLINE. MARK THE LOCATION FOR 2 ADDITIONAL, EVENLY

SPACED TOGGLE BOLTS IN THE MOUNTING PLATE

AREA.

Trim the rear wall template along the dotted line.

Trim the rear wall template along the dotted line.

12"

4"

Darle vuelta a la hoja para consultar la

versin en Espaol.

Make sure the motor wiring has

EN-16

3/8" TO EDGE

NOTE: IT IS VERY IMPORTANT TO

READ AND FOLLOW THE DIRECTIONS

IN THE INSTALLATION INSTRUCTIONS

BEFORE PROCEEDING WITH THIS

REAR WALL TEMPLATE.

This Rear Wall Template serves to position the bottom

mounting plate and to locate the horizontal exhaust

outlet. 1. Use a level to check that the template is positioned

accurately. 2. Locate and mark at least one stud on the left or

right side of the centerline.

It is important to use at least one wood

screw mounted firmly in a stud to support the weight

of the microwave. Mark two additional, evenly spaced

locations for the supplied toggle bolts.

3. Drill holes in the marked locations. Where there is

a stud, drill a 3/16" hole for wood screws. For holes

that do not line up with a stud, drill 5/8" holes for

toggle bolts. DO NOT INSTALL THE MOUNTING PLATE

AT THIS TIME.

4. Remove the template from the rear wall.

5. Review the Installation Instruction book for your

installation situation.

Locate and mark holes to align with holes in the

mounting plate.

IMPORTANT:

LOCATE AT LEAST ONE STUD ON EITHER SIDE OF

THE CENTERLINE.

MARK THE LOCATION FOR 2 ADDITIONAL, EVENLY

SPACED TOGGLE BOLTS IN THE MOUNTING PLATE

AREA. Locate and mark holes to align with holes in the

mounting plate.

IMPORTANT:

LOCATE AT LEAST ONE STUD ON EITHER SIDE OF

THE CENTERLINE.

MARK THE LOCATION FOR 2 ADDITIONAL, EVENLY

SPACED TOGGLE BOLTS IN THE MOUNTING PLATE

AREA. Trim the rear wall template along the dotted line.

Trim the rear wall template along the dotted line.

12"

4"

Darle vuelta a la hoja para consultar la

versin en Espaol.

IMPORTANT :Do not remove the cardboard spacers between the heat shield and door.

ATTACH THE MOUNTING PLATE TO THE WALL

B3. USE TOP CABINET TEMPLATE FOR PREPARATION OF TOP CABINET

B4.

Read the instructions on the TOP CABINET TEMPLATE.

Tape it underneath the top cabinet. Drill the holes, following the instructions on the

TOP CABINET TEMPLATE.

CAUTION: Wear safety goggles when drilling holes in the cabinet bottom.

Wall

Mounting Plate

Spacing for Toggles More Than Wall Thickness

Toggle Bolt

Toggle Wings

To use toggle bolts:

Bolt End

Installation Instructions

You need to drill holes for the top support screws and a hole large enough for the power cord to fit through.

Attach the plate to the wall using toggle bolts. At least one wood screw must be used to attach the plate to a wall stud.

Remove the toggle wings from the bolts.

Insert the bolts into the mounting plate through the holes designated to go into drywall and reattach the toggle wings to 34 (19 mm) onto each bolt.

1

2

Place the mounting plate against the wall and insert the toggle wings into the holes in the wall to mount the plate.

NOTE: Before tightening toggle bolts and wood screw, make sure the bottom of the mounting plate touch the bottom of the cabinet when pushed flush against the wall and that the plate is properly centered under the cabinet. CAUTION: Be careful to avoid pinching fingers between the back of the mounting plate and the wall.

Tighten all bolts. Pull the plate away from the wall to help tighten the bolts.

3

4

2

1 Remove and save screw that holds blower motor to microwave.

ADAPTING MICROWAVE BLOWER FOR OUTSIDE BACK EXHAUST

B5.

End B

End A

will extend far enough to allow you to adjust the blower unit.

Back of Microwave

Blower Motor

Blower Motor Screw

Forward Openings Facing

Carefully pull out the blower unit. The wires

Before: Fan Blade

EN-17

Attach the exhaust adaptor to the rear of the oven by sliding it into the guides at the top center of the back of the oven.

AFTER: Fan Blade Openings Facing Back

Place the blower unit back into the opening.

Replace the blower plate in the same position as before with the screw. Make sure the screw is tight.

Roll the blower unit 90 so that fan blade openings are facing out the back of the microwave.

ADAPTING MICROWAVE BLOWER FOR OUTSIDE BACK EXHAUST (cont.)

B5.

Rotate blower unit counterclockwise 180.

Before Rotation After Rotation

Gently remove the wires from the grooves. Reroute the wires through grooves on other side of the blower unit.

Before Rerouting After Rerouting

Wires Routed Through Right Side Wires Routed Through Left Side

Back of Microwave

Back of Microwave

Blower Plate

Blower Motor Screw

Secure the blower unit to the microwave with the original screw.

Before Rolling After Rolling

Back of Microwave

End A

End B

Back of Microwave

Back of Microwave

CAUTION: Do not pull or stretch the blower unit wiring. Make sure the wires are not pinched, and that they are properly secured.

NOTE: The blower unit exhaust openings should match exhaust openings on rear of microwave oven.

Installation Instructions

Push in securely until it is in the lower locking tabs. Take care to assure that the damper hinge is installed so that it is at the top and that the damper swings freely.

Guide

Guide

Adaptor

Locking Tabs

Back of Microwave

Back of Microwave

Roll the blower unit 90

Back of Microwave

3

4

5

6

7

8

9

10

Before Rotation After Rotation

EN-18

Attach the microwave oven to the top cabinet.

Installation Instructions

3

MOUNT THE MICROWAVE OVEN

B6.

FOR EASIER INSTALLATION AND PERSONAL SAFETY, WE RECOMMEND THAT TWO PEOPLE INSTALL THIS MICROWAVE OVEN.

NOTE: If your cabinet is metal, use the nylon grommet around the power cord hole to prevent cutting of the cord. NOTE: We recommend using filler blocks if the cabinet front hangs below the cabinet bottom shelf.

IMPORTANT: If filler blocks are not used, case damage may occur from overtightening screws.

Insert a self-aligning screw through top center cabinet hole. Temporarily secure the oven by turning the screw at least two full turns after the threads have engaged. (It will be completely tightened later.) Be sure to keep power cord tight. Be careful not to pinch the cord, especially when mounting flush to bottom of cabinet.

7

5

Cabinet Front

Cabinet Bottom Shelf

Tighten the outer two screws to the top of the microwave oven. (While tightening screws, hold the microwave oven in place against the wall and the top cabinet.)

Filler Block

Microwave Oven Top

Equivalent to Depth of Cabinet Recess

Insert 2 self-aligning screws through outer top cabinet holes. Turn two full turns on each screw.

Self-Aligning Screw

4

2 Rotate front of oven up against cabinet bottom.

NOTE: When mounting the microwave oven, thread power cord through hole in bottom of top cabinet. Keep it tight throughout Steps 13. Do not pinch cord or lift oven by pulling cord.

Lift microwave, tilt it forward, and hook slots at back bottom edge onto four lower tabs of mounting plate.

1

Tighten center screw completely.

6

EN-19

8 Install grease filters. See the Owners Manual packed with the microwave.

IMPORTANT: Remove the cardhoard spacers between heat shield and door.

IMPORTANT: Do not grip or use the handle or heat shield during installation. Do not remove the cardboard spacers between the heat shield and door.

INSTALLATION OVERVIEW C1. Attach Mounting Plate to Wall C2. Prepare Top Cabinet

C4. C5.

Mount the Microwave Oven

IMPORTANT NOTES: Make sure the screws for the blower motor and blower

plate are securely tightened when they are reinstalled. This will help to prevent excessive vibration.

Make sure the motor wiring has been properly routed and secured, and that the wires are not pinched.

Installation Instructions

RECIRCULATING (Non-Vented Ductless)C

Install or change Charcoal Filter

C3. Check Blower Plate

Place the mounting plate against the wall and insert the toggle wings into the holes in the wall to mount the plate.

NOTE: Before tightening toggle bolts and wood screw, make sure the bottom of the mounting plate touch the bottom of the cabinet when pushed flush against the wall and that the plate is properly centered under the cabinet. CAUTION: Be careful to avoid pinching fingers between the back of the mounting plate and the wall.

Tighten all bolts. Pull the plate away from the wall to help tighten the bolts.

4

3

ATTACH THE MOUNTING PLATE TO THE WALL

C1.

Attach the plate to the wall using toggle bolts. At least one wood screw must be used to attach the plate to a wall stud.

Remove the toggle wings from the bolts.

Insert the bolts into the mounting plate through the holes designated to go into drywall and reattach the toggle wings to 34 (19 mm) onto each bolt.

1

Wall

Mounting Plate

Spacing for Toggles More Than Wall Thickness

Bolt End

Toggle Bolt

Toggle Wings

To use toggle bolts:

2

NOTE:

CabinetCabinet

If the cabinet depth including the cabinet doors is more than 13""'' then the unit must be spaced out from wall using adequate materials supporting 150 Ibs to allow proper top vent air exhaust/intake.

EN-20

3/8" TO EDGE

NOTE: IT IS VERY IMPORTANT TO

READ AND FOLLOW THE DIRECTIONS

IN THE INSTALLATION INSTRUCTIONS

BEFORE PROCEEDING WITH THIS

REAR WALL TEMPLATE.

This Rear Wall Template serves to position the bottom

mounting plate and to locate the horizontal exhaust

outlet. 1. Use a level to check that the template is positioned

accurately. 2. Locate and mark at least one stud on the left or

right side of the centerline.

It is important to use at least one wood

screw mounted firmly in a stud to support the weight

of the microwave. Mark two additional, evenly spaced

locations for the supplied toggle bolts.

3. Drill holes in the marked locations. Where there is

a stud, drill a 3/16" hole for wood screws. For holes

that do not line up with a stud, drill 5/8" holes for

toggle bolts. DO NOT INSTALL THE MOUNTING PLATE

AT THIS TIME.

4. Remove the template from the rear wall.

5. Review the Installation Instruction book for your

installation situation.

Locate and mark holes to align with holes in the

mounting plate.

IMPORTANT:

LOCATE AT LEAST ONE STUD ON EITHER SIDE OF

THE CENTERLINE.

MARK THE LOCATION FOR 2 ADDITIONAL, EVENLY

SPACED TOGGLE BOLTS IN THE MOUNTING PLATE

AREA. Locate and mark holes to align with holes in the

mounting plate.

IMPORTANT:

LOCATE AT LEAST ONE STUD ON EITHER SIDE OF

THE CENTERLINE.

MARK THE LOCATION FOR 2 ADDITIONAL, EVENLY

SPACED TOGGLE BOLTS IN THE MOUNTING PLATE

AREA. Trim the rear wall template along the dotted line.

Trim the rear wall template along the dotted line.

12"

4"

Darle vuelta a la hoja para consultar la

versin en Espaol.

IMPORTANT :Do not remove the cardboard spacers between the heat shield and door.

Installation Instructions

Attach the microwave oven to the top cabinet.

Cabinet Front Cabinet Bottom Shelf

Filler Block

Microwave Oven Top

Equivalent to Depth of Cabinet Recess

3

MOUNT THE MICROWAVE OVEN

FOR EASIER INSTALLATION AND PERSONAL SAFETY, WE RECOMMEND THAT TWO PEOPLE INSTALL THIS MICROWAVE OVEN.

NOTE: If your cabinet is metal, use the nylon grommet around the power cord hole to prevent cutting of the cord. NOTE: We recommend using filler blocks if the cabinet front hangs below the cabinet bottom shelf. IMPORTANT: If filler blocks are not used, case damage may occur from overtightening screws.

Insert a self-aligning screw through top center cabinet hole. Temporarily secure the oven by turning the screw at least two full turns after the threads have engaged. (It will be completely tightened later.) Be sure to keep power cord tight. Be careful not to pinch the cord, especially when mounting flush to bottom of cabinet.

Self-Aligning Screw

4

2 Rotate front of oven up against cabinet bottom.

NOTE: When mounting the microwave oven, thread power cord through hole in bottom of top cabinet. Keep it tight throughout Steps 13. Do not pinch cord or lift oven by pulling cord.

Lift microwave, tilt it forward, and hook slots at back bottom edge onto four lower tabs of mounting plate.

1

C3.

C4.

CHECK BLOWER PLATE Blower Plate

Place the microwave in its upright position, with the top of the unit facing up.

Check to see that the blower plate is correctly installed on the unit.

USE TOP CABINET TEMPLATE FOR PREPARATION OF TOP CABINET

C2.

Read the instructions on the TOP CABINET TEMPLATE.

Tape it underneath the top cabinet.

Drill the holes, following the instructions on the TOP CABINET TEMPLATE.

CAUTION: Wear safety goggles when drilling holes in the cabinet bottom.

You need to drill holes for the top support screws and a hole large enough for the power cord to fit through.

Adjust top template accordingly if the microwave is being spaced out from the wall due to cabinet depth (including cabinet doors) of more th n 13"""''.

NOTE:

a

EN-21

IMPORTANT: Do not grip or use the handle or heat shield during installation. Do not remove the cardboard spacers between the heat shield and door.

Installation Instructions

5

MOUNT THE MICROWAVE OVEN (cont.)

7 Tighten the outer two screws to the top of the microwave oven. (While tightening screws, hold the microwave oven in place against the wall and the top cabinet.)

Insert 2 self-aligning screws through outer top cabinet holes. Turn two full turns on each screw.

C4.

Tighten center screw completely.

C5. INSTALLING OR CHANGE THE CHARCOAL FILTER (Some Models)

C

lose the microwave door. Plug in microwave oven or reconnect power.

Tip forward. Lift out to remove.3

Open the microwave door and remove the two vent mounting screws ;located on top of the microwave using a #1 Phillips screwdriver.

2

Unplug microwave oven or disconnect power.1

Install the charcoal filter. Lay the filter on the back4 of the grille with the black mesh face upper.

Tabs Charcoal filter

NOTE: The charcoal filter is factory installed in some models. Refer to the Use and Care to see if yours is factory installed and for replacement information. Follow these steps to replace or install a charcoal filter.

5

6

6

Reinstall the vent by sliding the bottom of the vent into place. Push the vent top into position and slide right into place. Replace the two vent mounting screws located on top of the microwave using a #1 Phillips screwdriver.

EN-22

8 Install grease filters. See the Owners Manual packed with the microwave.

IMPORTANT: Remove the cardhoard spacers between heat shield and door.

KEEP INSTALLATION INSTRUCTIONS FOR THE LOCAL INSPECTORS USE.

Plug power cord into a seperate and dedicated

7.

6. Remove all packing material from the microwave oven.

2.

Make sure the microwave oven has been installed according to instructions.1.

BEFORE YOU USE YOUR MICROWAVE

Ensure proper ground exists before use

INSTALLATION

INSTRUCTIONS

INSTALLATION

INSTRUCTIONS

MANUAL

3.

USE |++&= CARE

+

&

D G

DDDDDDD

PRODUCT

CARD

Read the Manual.

Installation Instructions

&

ring a nd glas s tray in cavity.Install turntable

REGISTRATION

USE CARE

Replace house fuse or turn breaker back on.

4.

5.

FILL OUT PRODUCT REGISTRATION CARD.8 AN SEND IN.

EN-23

15- to 20-amp electrical outlet.

Printed in ChinaEN-24

Locate and mark holes to align with holes in the mounting plate. IMPORTANT: LOCATE AT LEAST ONE STUD ON EITHER SIDE OF THE CENTERLINE. MARK THE LOCATION FOR 2 ADDITIONAL, EVENLY SPACED TOGGLE BOLTS IN THE MOUNTING PLATE AREA.

Locate and mark holes to align with holes in the mounting plate. IMPORTANT: LOCATE AT LEAST ONE STUD ON EITHER SIDE OF THE CENTERLINE. MARK THE LOCATION FOR 2 ADDITIONAL, EVENLY SPACED TOGGLE BOLTS IN THE MOUNTING PLATE AREA.

Trim the rear wall template along the dotted line.

Trim the rear wall template along the dotted line.

3/8" TO EDGE

12"

4"

NOTE: IT IS VERY IMPORTANT TO READ AND FOLLOW THE DIRECTIONS IN THE INSTALLATION INSTRUCTIONS BEFORE PROCEEDING WITH THIS REAR WALL TEMPLATE. This Rear Wall Template serves to position the bottom mounting plate and to locate the horizontal exhaust outlet. 1. Use a level to check that the template is positioned accurately. 2. Locate and mark at least one stud on the left or right side of the centerline. It is important to use at least one wood screw mounted firmly in a stud to support the weight of the microwave. Mark two additional, evenly spaced locations for the supplied toggle bolts. 3. Drill holes in the marked locations. Where there is a stud, drill a 3/16" hole for wood screws. For holes that do not line up with a stud, drill 5/8" holes for toggle bolts. DO NOT INSTALL THE MOUNTING PLATE AT THIS TIME. 4. Remove the template from the rear wall. 5. Review the Installation Instruction book for your installation situation.

Part No.:316902912

2

/ 1 -

4

3/8 3/ 83/8

3/ 8

13-3/8 8-1/4

2

2

12-1/2

6-1/4

2 3

/ 7

2 - 9

4 / 1

- 4

3/83/ 8

3/8

2

1/2

13-3/8

Part No.:77222316902475

3/8" TO EDGE

NOTE: IT IS VERY IMPORTANT TO READ AND FOLLOW THE DIRECTIONS

IN THE INSTALLATION INSTRUCTIONS

BEFORE PROCEEDING WITH THIS REAR WALL TEMPLATE.This Rear Wall Template serves to position the bottom

mounting plate and to locate the horizontal exhaust

outlet. 1. Use a level to check that the template is positioned

accurately. 2. Locate and mark at least one stud on the left or

right side of the centerline. It is important to use at least one wood

screw mounted firmly in a stud to support the weight

of the microwave. Mark two additional, evenly spaced

locations for the supplied toggle bolts.

3. Drill holes in the marked locations. Where there is

a stud, drill a 3/16" hole for wood screws. For holes

that do not line up with a stud, drill 5/8" holes for

toggle bolts. DO NOT INSTALL THE MOUNTING PLATE

AT THIS TIME. 4. Remove the template from the rear wall.

5. Review the Installation Instruction book for your

installation situation.

Locate and mark holes to align with holes in the

mounting plate. IMPORTANT: LOCATE AT LEAST ONE STUD ON EITHER SIDE OF

THE CENTERLINE. MARK THE LOCATION FOR 2 ADDITIONAL, EVENLY

SPACED TOGGLE BOLTS IN THE MOUNTING PLATE

AREA.

Locate and mark holes to align with holes in the

mounting plate. IMPORTANT: LOCATE AT LEAST ONE STUD ON EITHER SIDE OF

THE CENTERLINE. MARK THE LOCATION FOR 2 ADDITIONAL, EVENLY

SPACED TOGGLE BOLTS IN THE MOUNTING PLATE

AREA.

Trim the rear wall template along the dotted line.

Trim the rear wall template along the dotted line.

12"

4"

Darle vuelta a la hoja para consultar la

versin en Espaol.

3/8" TO EDGE

NOTE: IT IS VERY IMPORTANT TO

READ AND FOLLOW THE DIRECTIONS

IN THE INSTALLATION INSTRUCTIONS

BEFORE PROCEEDING WITH THIS

REAR WALL TEMPLATE.This Rear Wall Template serves to position the bottom

mounting plate and to locate the horizontal exhaust

outlet. 1. Use a level to check that the template is positioned

accurately. 2. Locate and mark at least one stud on the left or

right side of the centerline.

It is important to use at least one wood

screw mounted firmly in a stud to support the weight

of the microwave. Mark two additional, evenly spaced

locations for the supplied toggle bolts.

3. Drill holes in the marked locations. Where there is

a stud, drill a 3/16" hole for wood screws. For holes

that do not line up with a stud, drill 5/8" holes for

toggle bolts. DO NOT INSTALL THE MOUNTING PLATE

AT THIS TIME. 4. Remove the template from the rear wall.

5. Review the Installation Instruction book for your

installation situation.

Locate and mark holes to align with holes in the

mounting plate. IMPORTANT: LOCATE AT LEAST ONE STUD ON EITHER SIDE OF

THE CENTERLINE. MARK THE LOCATION FOR 2 ADDITIONAL, EVENLY

SPACED TOGGLE BOLTS IN THE MOUNTING PLATE

AREA.

Locate and mark holes to align with holes in the

mounting plate. IMPORTANT: LOCATE AT LEAST ONE STUD ON EITHER SIDE OF

THE CENTERLINE. MARK THE LOCATION FOR 2 ADDITIONAL, EVENLY

SPACED TOGGLE BOLTS IN THE MOUNTING PLATE

AREA.

Trim the rear wall template along the dotted line.

Trim the rear wall template along the dotted line.

12"

4"

Darle vuelta a la hoja para consultar la

versin en Espaol.

Darle vuelta a la hoja para consultar la versin en Espaol.

PN: 16170000A10767

LEA CUIDADOSAMENTE. CONSERVE ESTAS INSTRUCCIONES..

Nota para el consumidor:

Nivel de preparation tecnica:

La instalacion correcta es responsabilidad del instalador.

Las fallas del producto que resulten de una instalacin incorrecta no estn cubiertas bajo la garanta.

oPreguntas? Llame al

conserve estas instrucciones para referencia futura. la instalacion de este electrodomestico requiere conocimientos mecnicos y elctricos bsicos.

Lea estas instrucciones completamente y con atencin.

conserve estas instrucciones para uso futuro del inspector local.

asegrese de que se cumplan todas las normas y los cdigos relevantes. asegrese de dejar estas instrucciones en manos del consumidor.

1-877-435-3287(US) 1-800-265-8352(Canada)

p/n 316495163 Augusto 2015

Antes de usar el horno microondas

CONTENIDO Informacin general

Gua de la instalacin paso a paso

Extraccin superior externa

Montaje de instalacin la placa de en la ......................................................................12

Preparacin del gabinete superior .....................13

Verificacin del funcionamiento correcto del

A

B

C

Instrucciones de instalacin

Recirculacin

Instalacin del horno microondas ........................19

Preparacin del gabinete superior .....................17

Montaje de la placa de instalacin en la ........................................................................17

salida de extraccin trasera externa .................16

Acoplamiento del sistema de conductos .............15

Ajuste del adaptador de extraccin ..................15

regulador de extraccin .......................................14

Extraccin trasera externa ................................. 1619

Ajuste del ventilador del microondas para la extraccin superior externa

.............................. 12 15

Preparacin de la pared trasera para la

Desinstalacin del placa del ventilador

Instalacin o cambiar del filtro de carbn

Verificacin del conjunto del placa del ventilador

.............................. 23

Instalacin del horno microondas

Instalacin del horno microondas

La informacin de plantilla

.................... 1314

.................1415

................16

.......................17-18

............................................................ 20-22

....................................................................... 20

..................... 20

........................................................................ 21

..................21-22

.........22

............................................. 24

-

pared

pared

Ajuste del ventilador del microondas para la extraccin superior externa

Montaje de la placa de instalacin en la pared

Preparacin del gabinete superior

pared

Instrucciones importantes sobre seguridad ............................. 3

Requisitos elctricos .................................................................... 3

Daos-envo (transporte)/instalacin ...................................... 4

Piezas incluidas ............................................................................ 4

Herramientas necesarias .................................................................... 5

Colocacin de la placa de instalacin ........................... 6-8

Tipos de instalacin .................................................. 9-22

Campana extractora ........................................................ 10-11

Desintalacin la placa de instalacin .................... 6

Localizacin de las vigas de la pared ................... 6

Ubicacin de la placa para la pared .................... 7

Alineacin de la placa para la pared ................. 8

SP-2

INSTRUCCIONES IMPORTANTES SOBRE SEGURIDAD

REQUISITOS ELCTRICOS

Instrucciones de instalacin

Este product require un tomacorriente de tres clavijas con puesta a tierra. Antes de proceder con la instalacin del electrodomstico, el instalador debe realizar una verificacin de la continuidad de la puesta a tierra del tomacorriente, a fin de asegurarse de que es correcta. Si la puesta a tierra no es correcta o si el tomacorriente no cumple con los requisites elctricos descritos en este manual (en la seccin REQUISITOS ELCTRICOS), se deber solicitor a un elctricista calificado que corrija cualquier defecto detectado.

PRECAUCIN: por razones de seguridad personal, antes de comenzar con el proced- imiento de instalacin, retire el fusible correspondiente o desconecte el disyuntor domstico, a fin de evitar cualquier lesion personal causada por un choque elctric.

PRECAUCIN: por razones de seguridad personal, la superficie de instalacin debe ser capaz de soportar la carga del gabinete, adems del peso adicional del product (63 a 85 libras o 28,5 a 38,5kg), as como cargas adiciona- les de hasta 50 libras (22,7kg), o bien un peso total de 113 a 135 libras (51,3 a 61,2kg).

PRECAUCIN: por razones de seguridad personal, este product no puede ser instalado en espacios de gabinete tipo insular o peninsular. Debe ser atornillado (instalado) TANTO al gabinete superior, COMO a la pared.

NOTA: por razones de seguridad personal y para facilitar la instalacin, se recomienda que dos personas instalen el product. IMPORTANTE: LEA CUIDADOSAMENTE! POR RAZONES DE SEGURIDAD PERSONAL, EL ELECTRODOMSTICO DEBE QUEDAR DEBIDAMENTE PUESTO A TIERRA, PARA EVITAR CUALQUIER CHOQUE ELCTRICO QUE PUEDA CAUSAR LA MUERTE.

El cable de alimentacin de este product est de este product est equipado con un enchufe (con puesta a tierra) de 3 clavijas, compatible con un tomacorriente de pared (con puesta a tierra) de 3 clavijas, lo cual minimize la posibilidad de choque elctric causado por el producto.

Se debe solicitor a un elctricista calificado que inspeccione el tomacorriente de pared y el circuito elctrico correspondi- ente, a fin de asegurarse de que el tomacorriente est debidamente puesto a tierra. En caso de que el tomacorriente estndar disponible sea solamente para un enchufe de dos clavijas, es muy impor- tante solicitor a un elctricista calificado que lo reemplace con un tomacorriente de tres clavijas puesto a tierra.

BAJO NINGUNA CIRCUNSTANCIA CORTE, ALTERE O ELIMINE LA TERCERA CLAVIJA (TIERRA) DEL CABLE ELC- TRICO. NO USE UN CABLE ELCTRICO DE EXTENSIN.

La potencia nominal del product es de 120 voltios de CA, 60 Hertz, 15 amperios y 1,6 kilovatios. Debe ser conectado a un circuito separado y dedicado de alimentacin elctrica

Elctrical Code O NEC) de los vigentes locales correspondientes a la potencia nominal en kilovatios del apparato.

tomacorriente (con puesta a tierra) de un circuito separado

microondas. El tomacorriente y el elctrica deben ser instalados por y deben cumplir con el cdigo NEC

Antes de usar el electrodomstico, verifique la puesta a tierra del tomacorriente.

correspondientes del cdigo El dimetro del alambre

alimentacin elctrica deben ser

los EE.UU. o con las normas vigentes locales correspondientes.

debe estar situado en el espacio superior del gabinete en y dedicado de 15 a 20 amperios. El tomacorriente

SP-3

que tenga el voltaje y la frecuencia adecuados. debe cumplir con los requisitos

elctrico nacional (National EE.UU., o bien con las normas

El cable y el enchufe de conectados a un

el cual se instalar el circuito de alimentacin un elctricista calificado de

Tornillos para madera ( " x 2")

Tornillos de fiador (y tuercas de mariposa)

( " x 3")

Tornillos autoalinea -ntes para mquina

( "-28 x3 ")

Moldura aislante de nylon (para los gabinetes metlicos)

DAOS-ENVO (TRANSP -ORTE)/INSTALACIN

Instrucciones de instalacin

PIEZAS INCLUIDAS

KIT DE FERRETERA

PIEZA CANTIDAD

1

1

2

PIEZAS INCLUIDAS (CONT.)

INSTRUCCIONES DE INSTALACIN

KIT DE FERRETERA

1

1

1

1

1

Estante 1

GUA DE USOY CUIDADO

PIEZA CANTIDAD

2

2

3

1

1 4/ 1 4/

1 4

3 16

/

/

Si el producto ha resultado daado durante su envo (transporte), devulvalo a la tienda/el almacn donde to adquiri, para que lo reparen o lo cambien por uno nuevo.

Si el producto ha sido daado por el comprador, la reparacin o el reemplazo del producto es responsabilidad del comprador. Si el instalador (no el comprador) daa el producto, la reparacin o el reemplazo del mismo tendr que ser acordado entre el comprador y el instalador.

Las piezas de ferretera vienen dentro de un paquete (kit) incluido con el electrodomstico. Verifique que el paquete contiene todas las piezas listadas aqu. NOTA: se incluyen algunas piezas adicionales.

Plantilla para el gabinete

superior

Plantilla para la pared trasera

combinado

Instrucciones de instalacion

Guia de Uso y Cuidado

Filtros de grasa

Adaptador

Bandeja de vidrio

Anillo de la bandeja giratoria

Estante de alambre de conveccin

2

SP-4

Param algunos modelos

Param algunos modelos

HERRAMIENTAS NECESARIAS

Destornillador Phillips #1 Lpiz

Regla o cinta mtrica con borde recto

Escuadra de carpintero (opcional)

Martillo (opcional)Detector de vigas (entramado)

o

Guantes

Nivel

Instrucciones de instalacin

Gafas de seguridad

ESPACIO PARA LA INSTALACIN

Protector contra salpicaduras

30(76.2 cm)

2 (5.1 cm)

30 (76.2 cm)

min.

17 1 2 (41.9cm

)

13 Mximo (33 cm)

GabineteGabinete

NOTAS:

Si la profundidad del gabinete incluyendo las puertas es mayor de 13" entonces la unidad debe alejarse de la pared con materiales adecuados que soporten 150 lbs para permitir una ventilacin adecuada/toma de aire.

/

Tijera para hojalata (para recortar el regulador de extraccin,si fuera necesario)

Tijera (para cortar las plantillas si fuera necesario) Taladro elctrico con brocas

de 3/16", 1/2" y 5/8" Bloques de relleno o de madera sobrante, si fueran necesarios para el espacio del gabinete superior (se utilizan solamente en instalaciones de gabinetes con la superficie inferior hueca)

Herramienta para cortar (serrucho sierra elctrica o segueta)

El borde inferior del gabinete debe quedar a 30"(76,2 cm) o ms de la superficie de coccin

El espacio entre los gabinetes debe ser de 30" (76,2 cm) de ancho v libre de obstrucciones. Si la extraccin de aire para el horno microondas ser dirigida hacia fuera de la cocina, consulte la seccin sobre campana extractora, para informarse sobre la preparacin del conducto de extraccin. Si va a instalar el horno microondas debajo de un gabinete plano y liso, tenga cuidado de seguir las instrucciones sobre la plantilla para el gabinete superior, especialmente la parte relacionada con el espacio libre para el cable elctrico. Como el gua de la instalacin, se vea el pgina 24 por la informacin de plantilla montada.

Cinta aislante y cinta de pintor

66"(167.6 cm) o ms desde el piso hasta la parte superior del microondas

SP-5

COLOCACIN DE LA PLACA DE INSTALACIN1

Instrucciones de instalacin

1

LOCALIZACIN DE LAS VIGAS DE LA PARED

B.

A.

2

Vigas de la pared

Centro

3

Caja de cartn

Tire de la caja de cartn hacia arriba, para separarla del horno.

2

Espuma de poliestireno

3

1

Tornillos Tornillos

Placa de instalacin

5

4 Come la bolsa de plstico en el medio para retirar la placa de instalacin.

Adaptador de escape Bolsa de accesorios pequea

Bandeja de vidrio

Estante

Doble hacia atrs las 4 lengetas de la caja de cartn, para que queden contra los lados de la caja. A continu- acin, d la vuelta con cuidado al horno y la caja, para que la caja quede en la parte superior. El horno quedar colocado sobre el protector de espuma.

Quite los tornillos de la placa de instalacin. Dicha placa se utilizar como plantilla para la pared trasera y para la instalacin. Vuelva a insertar los tornillos en los agujeros de los cuales haban sido extrados.

Localice las vigas mediante cualquiera de los mtodos siguientes: A. Detector de vigas. aparato magntico que detecta clavos. B. Use un martillo para dar golpecitos leves sobre la superficie de instalacin, a fin de detectar el sonido de superficie maciza (no hueca). Esto indicar la ubicacin de una viga. Tras localizar la(s) viga(s), localice su centro haciendo pruebas en la pared con un pequeo clavo que le permita detectar los bordes de la viga. A continuacin, haga una marca que quede a la mitad de ambos bordes. El centro de cualquier viga adyacente debe quedar a 16" (40,6 cm) o 24" (61 cm) de dicha marca. Trace una lnea hacia abajo del centro de las vigas. EL MICROONDAS DEBE QUEDAR ATORNILLADO AL MENOS A UNA VIGA DE LA PARED

PROCEDIMIENTO PARA SACAR DE LA CAJA EL MICROONDAS Y LA PLACA DE INSTALACIN

Retirar las instrucciones de instalacin, uso y cuidado, adaptador de escape, anillo giratorio, estante, filtros, bandeja de vidrio y bolsa de accesorios pequea. No retire el poliestireno de la parte delantera del horno.

Anillo giratorio debajo de la bandeja de vidrio

SP-6

C.

C

3/8" TO EDGE

NOTE: IT IS VERY IMPORTANT TO

READ AND FOLLOW THE DIRECTIONS

IN THE INSTALLATION INSTRUCTIONS

BEFORE PROCEEDING WITH THIS

REAR WALL TEMPLATE. This Rear Wall Template serves to position the bottom

mounting plate and to locate the horizontal exhaust

outlet. 1. Use a level to check that the template is positioned

accurately. 2. Locate and mark at least one stud on the left or

right side of the centerline. It is important to use at least one wood

screw mounted firmly in a stud to support the weight

of the microwave. Mark two additional, evenly spaced

locations for the supplied toggle bolts.

3. Drill holes in the marked locations. Where there is

a stud, drill a 3/16" hole for wood screws. For holes

that do not line up with a stud, drill 5/8" holes for

toggle bolts. DO NOT INSTALL THE MOUNTING PLATE

AT THIS TIME. 4. Remove the template from the rear wall.

5. Review the Installation Instruction book for your

installation situation.

Locate and mark holes to align with holes in the

mounting plate. IMPORTANT: LOCATE AT LEAST ONE STUD ON EITHER SIDE OF

THE CENTERLINE. MARK THE LOCATION FOR 2 ADDITIONAL, EVENLY

SPACED TOGGLE BOLTS IN THE MOUNTING PLATE

AREA.

Locate and mark holes to align with holes in the

mounting plate. IMPORTANT: LOCATE AT LEAST ONE STUD ON EITHER SIDE OF

THE CENTERLINE. MARK THE LOCATION FOR 2 ADDITIONAL, EVENLY

SPACED TOGGLE BOLTS IN THE MOUNTING PLATE

AREA.

Trim the rear wall template along the dotted line.

Trim the rear wall template along the dotted line.

12"

4"

Darle vuelta a la hoja para consultar la

versin en Espaol.

3/8" TO EDGE

NOTE: IT IS VERY IMPORTANT TO

READ AND FOLLOW THE DIRECTIONS

IN THE INSTALLATION INSTRUCTIONS

BEFORE PROCEEDING WITH THIS

REAR WALL TEMPLATE. This Rear Wall Template serves to position the bottom

mounting plate and to locate the horizontal exhaust

outlet. 1. Use a level to check that the template is positioned

accurately. 2. Locate and mark at least one stud on the left or

right side of the centerline. It is important to use at least one wood

screw mounted firmly in a stud to support the weight

of the microwave. Mark two additional, evenly spaced

locations for the supplied toggle bolts.

3. Drill holes in the marked locations. Where there is

a stud, drill a 3/16" hole for wood screws. For holes

that do not line up with a stud, drill 5/8" holes for

toggle bolts. DO NOT INSTALL THE MOUNTING PLATE

AT THIS TIME. 4. Remove the template from the rear wall.

5. Review the Installation Instruction book for your

installation situation.

Locate and mark holes to align with holes in the

mounting plate. IMPORTANT: LOCATE AT LEAST ONE STUD ON EITHER SIDE OF

THE CENTERLINE. MARK THE LOCATION FOR 2 ADDITIONAL, EVENLY

SPACED TOGGLE BOLTS IN THE MOUNTING PLATE

AREA.

Locate and mark holes to align with holes in the

mounting plate. IMPORTANT: LOCATE AT LEAST ONE STUD ON EITHER SIDE OF

THE CENTERLINE. MARK THE LOCATION FOR 2 ADDITIONAL, EVENLY

SPACED TOGGLE BOLTS IN THE MOUNTING PLATE

AREA.

Trim the rear wall template along the dotted line.

Trim the rear wall template along the dotted line.

12"

4"

Darle vuelta a la hoja para consultar la

versin en Espaol.

C

3/8" TO EDGE

NOTE: IT IS VERY IMPORTANT TO

READ AND FOLLOW THE DIRECTIONS

IN THE INSTALLATION INSTRUCTIONS

BEFORE PROCEEDING WITH THIS

REAR WALL TEMPLATE. This Rear Wall Template serves to position the bottom

mounting plate and to locate the horizontal exhaust

outlet. 1. Use a level to check that the template is positioned

accurately. 2. Locate and mark at least one stud on the left or

right side of the centerline. It is important to use at least one wood

screw mounted firmly in a stud to support the weight

of the microwave. Mark two additional, evenly spaced

locations for the supplied toggle bolts.

3. Drill holes in the marked locations. Where there is

a stud, drill a 3/16" hole for wood screws. For holes

that do not line up with a stud, drill 5/8" holes for

toggle bolts. DO NOT INSTALL THE MOUNTING PLATE

AT THIS TIME. 4. Remove the template from the rear wall.

5. Review the Installation Instruction book for your

installation situation.

Locate and mark holes to align with holes in the

mounting plate. IMPORTANT: LOCATE AT LEAST ONE STUD ON EITHER SIDE OF

THE CENTERLINE. MARK THE LOCATION FOR 2 ADDITIONAL, EVENLY

SPACED TOGGLE BOLTS IN THE MOUNTING PLATE

AREA.

Locate and mark holes to align with holes in the

mounting plate. IMPORTANT: LOCATE AT LEAST ONE STUD ON EITHER SIDE OF

THE CENTERLINE. MARK THE LOCATION FOR 2 ADDITIONAL, EVENLY

SPACED TOGGLE BOLTS IN THE MOUNTING PLATE

AREA.

Trim the rear wall template along the dotted line.

Trim the rear wall template along the dotted line.

12"

4"

Darle vuelta a la hoja para consultar la

versin en Espaol.

C

3/8" TO EDGE

NOTE: IT IS VERY IMPORTANT TO

READ AND FOLLOW THE DIRECTIONS

IN THE INSTALLATION INSTRUCTIONS

BEFORE PROCEEDING WITH THIS

REAR WALL TEMPLATE. This Rear Wall Template serves to position the bottom

mounting plate and to locate the horizontal exhaust

outlet. 1. Use a level to check that the template is positioned

accurately. 2. Locate and mark at least one stud on the left or

right side of the centerline. It is important to use at least one wood

screw mounted firmly in a stud to support the weight

of the microwave. Mark two additional, evenly spaced

locations for the supplied toggle bolts.

3. Drill holes in the marked locations. Where there is

a stud, drill a 3/16" hole for wood screws. For holes

that do not line up with a stud, drill 5/8" holes for

toggle bolts. DO NOT INSTALL THE MOUNTING PLATE

AT THIS TIME. 4. Remove the template from the rear wall.

5. Review the Installation Instruction book for your

installation situation.

Locate and mark holes to align with holes in the

mounting plate. IMPORTANT: LOCATE AT LEAST ONE STUD ON EITHER SIDE OF

THE CENTERLINE. MARK THE LOCATION FOR 2 ADDITIONAL, EVENLY

SPACED TOGGLE BOLTS IN THE MOUNTING PLATE

AREA.

Locate and mark holes to align with holes in the

mounting plate. IMPORTANT: LOCATE AT LEAST ONE STUD ON EITHER SIDE OF

THE CENTERLINE. MARK THE LOCATION FOR 2 ADDITIONAL, EVENLY

SPACED TOGGLE BOLTS IN THE MOUNTING PLATE

AREA.

Trim the rear wall template along the dotted line.

Trim the rear wall template along the dotted line.

12"

4"

Darle vuelta a la hoja para consultar la

versin en Espaol.

1

3

2

17-1/2

UBICACIN DE LA PLACA PARA LA PARED DE BAJO DEL GABINETE

Instrucciones de instalacin

Posicin de la placa-debajo de la superficie plana inferior del gabinete

Posicin de la place-debajo de la superficie hueca inferior (con marco) del gabinete

Dibuja una lnea vertical en la pared en el centro del espacio cuyo ancho es 30". Cinta la Plantilla de pared posterior en la pared correspondiente a la lnea y toca el fondo del armario.

Trace una lnea en el fundo de la pared igal a la profundidad del voladizo delantero

30" a la superficie de coccin

Dibuja una lnea vertical en la pared en el centro del espacio cuyo ancho es 30". Cinta la Plantilla de pared posterior en la pared correspondiente a la lnea y toca el fondo del armario.

Es posible que sus gabinetes tengan molduras decorati- vas que interfieran con la instalacin del microondas. En este caso, quite dichas molduras para poder instalar correctamente el microondas y que quede nivelado.

EL MICROONDAS DEBE QUEDAR NIVELADO. Use un nivel para asegurarse de que la superficie inferior del gabinete est nivelada. Si el gabinete tiene solamente una parte delantera saliente, sin parte trasera o lateral del marco, instale la placa de instalacin a la misma distancia que la distancia de profundidad de la parte saliente delantera. Esto mantendr el microondas nivelado.

Mida la distancia de profundidad interior de la parte saliente delantera. Trace una lnea horizontal en la pared trasera, debajo de la superficie inferior del gabinete, a una distancia igual que la distancia de profundidad interior de la parte saliente delantera. Solamente en el caso de este tipo de instalacin con parte saliente delantera, alinee las lengetas de instalacin con dicha lnea horizontal, sin tocar la superficie inferior del gabinete, como se describe en el paso D.

Posicin de la placa-debajo de la superficie hueca saliente, delantera e inferior (con marco) del gabinete

30" a la superficie de coccin

Al menos 30"

SP-7

Instrucciones de instalacin

D.

CL

3/8" TO EDGE

NOTE: IT IS VERY IMPORTANT TO READ AND FOLLOW THE DIRECTIONS IN THE INSTALLATION INSTRUCTIONS BEFORE PROCEEDING WITH THIS REAR WALL TEMPLATE. This Rear Wall Template serves to position the bottom mounting plate and to locate the horizontal exhaust outlet. 1. Use a level to check that the template is positioned accurately. 2. Locate and mark at least one stud on the left or right side of the centerline.

It is important to use at least one wood screw mounted firmly in a stud to support the weight of the microwave. Mark two additional, evenly spaced locations for the supplied toggle bolts. 3. Drill holes in the marked locations. Where there is a stud, drill a 3/16" hole for wood screws. For holes that do not line up with a stud, drill 5/8" holes for toggle bolts.

DO NOT INSTALL THE MOUNTING PLATE AT THIS TIME. 4. Remove the template from the rear wall. 5. Review the Installation Instruction book for your installation situation.

Locate and mark holes to align with holes in the mounting plate. IMPORTANT: LOCATE AT LEAST ONE STUD ON EITHER SIDE OF THE CENTERLINE. MARK THE LOCATION FOR 2 ADDITIONAL, EVENLY SPACED TOGGLE BOLTS IN THE MOUNTING PLATE AREA.

Locate and mark holes to align with holes in the mounting plate. IMPORTANT: LOCATE AT LEAST ONE STUD ON EITHER SIDE OF THE CENTERLINE. MARK THE LOCATION FOR 2 ADDITIONAL, EVENLY SPACED TOGGLE BOLTS IN THE MOUNTING PLATE AREA.

Trim the rear wall template along the dotted line. 12"

4"

Darle vuelta a la hoja para consultar la versin en Espaol.

ALINEACIN DE LA PLACA PARA LA PARED

rea E Agujero A

Agujero B

Muescas de la lnea de centro

Dibula una Inea vertical en la pared desde el centro del cumbre del armario.

Trace una lnea horizontal en la pared desde el fondo de "Plantilla de pared posterior".

La lnea horizontalLa lnea horizontal

1

2

3

4

Trace una lnea vertical en la pared, en el centro del espacio cuyo ancho es 30".

Trace una lnea horizontal en la pared desde el fondo de "Plantilla de pared posterior."

Encuentre un travesao en el rea E de la placa de montaje. Consulte la seccin 1B: Encontrar travesa- os de pared.

NOTA: Los Agujero A y los Agujero B se encuentran dentro de la regin E. Si tanto el agujero C como el D no quedan en una viga, localice una viga en el rea E y trace un quinto crculo que quede alineado con la viga. Es importante que al menos un tornillo para madera quede fijado firmemente a una viga, a fin de que pueda soportar el peso del microondas. Deje a un lado la placa de instalacin.

Para adherir la placa de montaje al travesao taladre un agujero de 3/16''. Taladre un agujero de 5/8'' para tornillo acodado en otra ubicacin (Agujero A o Agujero B). NOTA: NO INSTALE LA PLACA EN ESTE MOMENTO.

PRECAUCIN: para evitar cortes por los bordes afilados.

SP-8

A

TIPOS DE INSTALACIN (A Eleccin Entre A, B o C)

Este horno microondas est diseado para adaptarse a los tres tipos siguientes de ventilacin: A. Extraccin superior externa (conducto vertical) B. Extraccin trasera externa (conducto horizontal) C. Recirculacin (sin conducto de extraccin)

EXTRACCIN SUPERIOR EXTERNA (CONDUCTO VERTICAL)

EXTRACCIN TRASERA EXTERNA (CONDUCTO HORIZONTAL)

RECIRCULACIN (SIN CONDUCTO DE EXTRACCIN)

Consulte la pgina 12

2

B

C

Consulte la pgina 16

Consulte la pgina 20

Instrucciones de instalacin

NOTA: este horno microondas se ha fbricado para un sistema de Recirculacin. Seleccione el tipo de ventilacin necesario para su instalacin y proceda con las instrucciones de la seccin correspondiente.

El adaptador est en posicin correcta para la extraccin superior externa

El adaptador debe ser recolocado en la parte trasera, para permitir la extraccin trasera externa

Los modelos fbricados para un sistema de extraccin basado en la recirculacin del aire vienen con la instalacin de fbrica de un filtro de carbn, el cual ayuda a eliminar el humo/los vapores y los olores.

NOTA: lea las dos pginas siguientes solamente si va a instalar un sistema de extraccin hacia el exterior. Si tiene planeado realizar una instalacin basada en la recirculacin del aire dentro de la cocina, contine con la pging 20.

SP-9

=xPIEZAS DEL CONDUCTO

Adaptador de unin entre el conducto rectangular y el redondo*

Pies o m (metros)

=) (x5 pies (1,5 m)

Tapa de salida a la pared

=) (x10 pies (3 m) Codo de 90

=) (x5 pies (1,5m) Codo de 45

=) (x25 pies (7,6 m)Codo de 90

=) (x5 pies (1,5 m)Codo de 45

=) (x1pies (0,3m)

Tapa d salida al techo

Conducto recto redondo de 6" (15,2 cm) de dimetro o rectangular de 31/4" 10" (8,2 25,4 cm) de ancho

Instrucciones de instalacin INSTRUCCIONES DE INSTALACIN DE CONDUCTOS DE ESCAPE EXTERNAS

NOTA: en caso de que sea necesario instalar conductos, tenga en cuenta que el largo total de los conductos. rectangulares (ancho de 3 1/4" 10" u 8,2 cm 25,4 cm) o redondos (dimetro de 5" 12,7 cm) /(dimetro de 6" 15,2 cm) NO debe ser superior a 120 pies (36,5 m). La ventilacin exterior requiere el uso de un CONDUCTO PARA CAMPANA EXTRACTORA. Lea con atencin las siguientes recomendacio- nes. NOTA: es importante que se instale el sistema de ventilacin siguiendo la ruta ms directa y con el menor nmero posible de codos. Esto garan- tizar la salida fluida del aire por los conductos de extraccin y evitar cualquier bloqueo. Asimismo, asegrese de que los reguladores de extraccin se muevan libremente y nada bloquee los conductos.

Largo mximo del conducto: Para lograr una salida satisfactoria del aire, el largo total del conducto rectangular con un ancho de 3 1/4" 10" (8,2 25,4 cm) o redondo con un dimetro de 5" (12,7 cm) /6" (15,2 cm) no debe ser mayor que 120 pies (36,5 m).

Los codos, los adaptadores, las tapas de salida al techo o a la pared, etc., representan reas de resistencia adicional al flujo del aire y son equivalentes a una seccin de conducto recto cuyo largo es mayor que su tamao fsico real. Cuando calcule el largo total del conducto, aada el largo equivalente de cada uno de los adaptadores, codos, etc., ms el largo de todas las secciones rectas del conducto. La tabla siguiente contiene infonnacin para saber cmo calcular el largo total (en medidas equivalentes) del sistema de conductos, a partir del largo aproximado en pies de algunos conductos/adaptadores/codos, etc. estndar.

LARGO (MEDIDAS EQUIVALENTES)

No DE UNIDADES- UTILIZADAS

LARGO (MEDIDAS EQUIVALENTES)

Pies o m (metros)

Pies o m (metros)

Pies o m (metros)

Pies o m (metros)

Pies o m (metros)

Pies o m (metros)

Pies o m (metros)

Pies o m (metros)Largo total del sistema de conductos =

40 pies (12,2 m) x ( ) =

=x ( )24 pies (7,3 m)

*IMPORTANTE: si se utiliza un adaptador de unin entre el conducto rectangular y el redondo, los bordes inferiores del regulador de extractin tendrn que ser recortados (con una tijera para hojalata), a fin de que se ajusten y permitan el libre mocvimiento del regulador.

Los largos (en medidas equivalentes) de las piezas del conducto estn basados en pruebas reales y se ajustan a los requisitos para un buen rendimiento de ventilacin con cualquier campana eatractora.

Conexin de escape El adaptador fue diseado para concordar con un ducto rectancular estpandar 31/4" x 10" (8.2 x 25.4 cm). Si se requiere de un ducto redondo, se debe utilizar un adaptador de transicin. Un ducto con un dimetro de 5" (12.7cm) / 6" (15.2cm) es aceptable.

SP-10

La siguiente tabla contiene un ejemplo de una posible instalacin de un sistema de conducto de extraccin.

EXTRACCIN SUPERIOR EXTERNA (SLO EJEMPLO) La siguiente tabla contiene un ejemplo de uno posible instalacin de un sistema de conducto de extraccin.

Instrucciones de instalacin

EXTRACCIN TRASERA EXTERNA (SLO EJEMPLO)

CONDUCTOS DE ESCAPE EXTERNAS

Tapa d salida al techo 24 pies (7,3 m)

41 pies (12,5 m)Largo total del sistema de conductos =

=x (1)24 pies (7,3 m)

=xPIEZAS DEL CONDUCTO LARGO (MEDIDAS EQUIVALENTES)

No DE UNIDADES- UTILIZADAS

LARGO (MEDIDAS EQUIVALENTES)

12 pies (3,6 m)=x (1)12 pies (3,6 m)

40 pies (12,2 m)=x (1)40 pies (12,2 m)

3 pies (0.9 m)=x (1)3 pies (0.9 m)

20 pies (3 m)=x (2)10 pies (3 m)

=xPIEZAS DEL CONDUCTO LARGO (MEDIDAS EQUIVALENTES)

No DE UNIDADES- UTILIZADAS

LARGO (MEDIDAS EQUIVALENTES)

5 pies (1,5 m)=x (1)5 pies (1,5 m)

Conducto recto de 12 pies (3,6 m) y dimetro de 6" (15,2 cm)

Adaptador de unin entre el conducto rectangular y el redondo*

Los largos (en medidas equivalentes) de las piezas del conducto estn basados en pruebas reales y se ajustan a los requisitos para un buen rendimiento de ventilacin con cualquier campana extractora.

Los largos (en medidas equivalentes) de las piezas del conducto estn basados en pruebas reales y se ajustan a los requisitos para un buen rendimiento de ventilacin con cualquier campana extractora.

63 pies (19,2 m)Largo total del sistema de conductos =

* IMPORTANTE: si se utiliza un adaptador le unin entre el conducto rectangular y el redondo, los bordes inferiores del regula- dor de extraccin tendrn que ser recortados (con una tijera para hojalata), a fin de que se ajusten y permitan el libre movimiento del regulador.

Tapa de salida a la pared

Conducto recto rectangular de 3 pies (0,9 m) de largo (3 y 1/4" 10" (8,2 cm 25,4 cm) de ancho

Codo de 90 o

NOTA: en el caso de extraccin por la parte trasera, hay que tener cuidado de alinear los conductos de extraccin con el espacio entre las vigas (el entramado), o bien que la pared haya sido preparada durante su construccin para dejar suficiente espacio entre las vigas para el sistema de extraccin.

SP-11

3

4

MONTAJE DE INSTALACIN LA PLACA DE EN LA PARED

A1.

1

Pared

Placa de instalacin

El espacio que ocupan los tornillos fiadores es superior al grueso de la pared

Extremo de tornillo

Tornillo fiador

Tuercas de mariposa

Para utilizar tornillos de fiador:

Instrucciones de instalacin

2

EXTRACCIN SUPERIOR EXTERNA (conducto vertica)A

DESCRIPCIN GENERAL DE LA INSTALACIN A1. Montaje de la placa de instalacin en la pared. A2. Preparacin del gabinete superior. A3. Ajuste del ventilador del microondas para la extraccin superior externa. A4. Verificacin del funcionamiento del regulador de extraccin. A5. Instalacin del horno microondas. A6. Ajuste del adaptador de extraccin. A7. Acoplamiento del sistema de conductos.

NOTAS IMPORTANTES: Asegrese de que los tornillos del-motor del ventilador y la placa del ventilador queden firmemente apretados al volver a instalarlos. Esto ayudar a prevenir el exceso de vibraciones. Asegrese de que el cableado del motor quede debidamente orientado y asegurado, y que los cables no queden atrapados.

Fije la placa en la pared con los tornillos de fiador. Al menos un tornillo para madera debe ser utilizado para fijar la placa a una viga de la pared.

Quite las tuercas de mariposa de los tornillos. Inserte los tornillos en la placa de instalacin, a travs de los agujeros taladrados en las partes de la pared que no son viga (los paneles) y vuelva a insertar las tuercas de mariposa hasta 3/4" (19 mm) de cada tornillo.

Coloque la placa de instalacin contra la pared e inserte las tuercas de mariposa en los agujeros de la pared, a fin de instalar la placa.

NOTA: antes de apretar los tornillos de fiador y el tornillo para madera, asegrese de que las lengetas de la placa de instalacin toquen la parte inferior del gabinete cuando sean empujadas a ras contra la pared, y que la placa quede debidamente centrada bajo el gabinete. PRECAUCIN: tenga cuidado de evitar que sus dedos queden atrapados entre la parte trasera de la placa de instalacin y la pared.

Apriete todos los tornillos. Tire de la placa alejndola de la pared, a fin de que resulte ms fcil apretar los tornillos.

SP-12

3/8" TO EDGE

NOTE: IT IS VERY IMPORTANT TO

READ AND FOLLOW THE DIRECTIONS

IN THE INSTALLATION INSTRUCTIONS

BEFORE PROCEEDING WITH THIS

REAR WALL TEMPLATE.

This Rear Wall Template serves to position the bottom

mounting plate and to locate the horizontal exhaust

outlet. 1. Use a level to check that the template is positioned

accurately. 2. Locate and mark at least one stud on the left or

right side of the centerline.

It is important to use at least one wood

screw mounted firmly in a stud to support the weight

of the microwave. Mark two additional, evenly spaced

locations for the supplied toggle bolts.

3. Drill holes in the marked locations. Where there is

a stud, drill a 3/16" hole for wood screws. For holes

that do not line up with a stud, drill 5/8" holes for

toggle bolts. DO NOT INSTALL THE MOUNTING PLATE

AT THIS TIME.

4. Remove the template from the rear wall.

5. Review the Installation Instruction book for your

installation situation.

Locate and mark holes to align with holes in the

mounting plate.

IMPORTANT:

LOCATE AT LEAST ONE STUD ON EITHER SIDE OF

THE CENTERLINE.

MARK THE LOCATION FOR 2 ADDITIONAL, EVENLY

SPACED TOGGLE BOLTS IN THE MOUNTING PLATE

AREA. Locate and mark holes to align with holes in the

mounting plate.

IMPORTANT:

LOCATE AT LEAST ONE STUD ON EITHER SIDE OF

THE CENTERLINE.

MARK THE LOCATION FOR 2 ADDITIONAL, EVENLY

SPACED TOGGLE BOLTS IN THE MOUNTING PLATE

AREA. Trim the rear wall template along the dotted line.

Trim the rear wall template along the dotted line.

12"

4"

Darle vuelta a la hoja para consultar la

versin en Espaol.

IMPORTANTE: no retire los separadores de

cartn entre el escudo trmico y la puerta.

A2.

Instrucciones de instalacin

A3.

Placa del ventilador

Tornillo del motor del ventilador

Parte trasera del microondas

2

Extremo B

Extremo A

1

3

Parte trasera del microondas

Antes de girar Despus de girar

Parte trasera del microondas

Parte trasera del microondas

Parte trasera del microondas

DESPUS: Aberturas de las aletas del ventilador orlentadas hacla arriba

Vuelva a colocar el ventilador dentro de su abertura.4

Coloque el microondas en posicin vertical, con la parte superior hacia arriba.

USO DE LA PLANTILLA PARA EL GABINETE SUPERIOR A FIN DE PREPARAR EL REA DE DICHO GABINETE

Es necesario taladrar agujeros para los tornillos de soporte superior, realizar un agujero lo suficientemente grande para que el cable elctuco pueda pasar a travs y recortar tambin un hueco to suficientemente amplio para el adaptador de extraccin.

Lea las instrucciones de la seccin PLANTILLA PARA EL GABINETE SUPERIOR. Adhiera con cinta la plantilla al gabinete superior. Taladre los agujeros, siguiendo las instrucciones de la seccin PLANTILLA PARA EL GABINETE SUPERIOR.

PRECAUCIN: cuando taladre los agujeros en la superficie inferior del gabinete, use gafas protectoras.

AJUSTE DEL VENTILADOR DEL MICROONDAS PARA LA EXTRAC- CIN SUPERIOR EXTERNA

Quite el tornillo que sujeta la placa del ventilador al microondas. Quite y guarde el tornillo que sujeta el motor del ventilador al microondas.

Tire del ventilador con cuidado hacia afuera. Los cables se extendern lo suficiente para permitir el ajuste del ventilador.

Gire el ventilador 90 , de manera que las aberturas de las aletas del ventilador queden orientadas hacia la parte superior del microondas.

o

PRECAUCIN: No tire hacia afuera ni estire los cables del ventilador. Asegrese de que los cables no queden atrapados y que queden debidamente asegurados.

SP-13

3

2

1

Adaptador de extraccinPlaca del ventilador Regulador de extraccin

Parte trasera del microondas

A3.

5

Parte trasera del microondas

6

7

Parte trasera del microondas

Adaptador

Gua

Lengetas de Bloqueo

A4.

A5.

Instrucciones de instalacin

Fije el ventilador al microondas con el tornillo previamente retirado en el paso l. Asegrese de apretar el tornillo.

AJUSTE DEL VENTILADOR DEL MICROONDAS PARA LA EXTRAC- CIN SUPERIOR EXTERNA

Vuelva a fijar la placa del ventilador con el tornillo previa- mente retirado en el paso 1. Asegrese de apretar el tornillo.

Instale el adaptador de extraccin en la parte superior del placa del ventilador, deslizndolo por las guas situadas en la parte central superior de la parte superior del placa del ventilador.

Empuje hacia adentro hasta que encaje en las lengetas de bloqueo inferiores. Tenga cuidado de asegurarse de que la bisagra del regulador de extraccin est instalada de manera que quede movible libremente.

VERIFICACIN DEL FUNCIONA- MIENTO CORRECTO DEL REGU- LADOR DE EXTRACCIN

Antes de instalar el microondas, asegrese de que la cinta adhesiva que protege el regulador de extraccin haya sido retirada y que el regulador se mueve fcilmente. Una vez instalado el microondas, necesitar realizar ajustes para asegurarse de lograr la alineacin correcta con el conducto de extraccin de la cocina.

POR RAZONES DE SEGURID PERSONAL Y PARA FACILITAR LA INSTALACIN, SE RECOMIENDA QUE DOS PERSONAS INSTALEN EL HORNO MICROONDAS.

NOTA: si el gabinete es metlico, use una moldura aislante de nylon alrededor del agujero para el cable elctrico, a fin de evitar cortes en el cable. NOTA: se recomienda el uso de bloques de relleno si la parte delantera del gabinete sobresale debajo de la parte inferior del propio gabinete. IMPORTANTE: Si no se usan bloques de relleno, pueden producirse daos en la carcasa por apretar demasiado los tornillos.

INSTALACIN DEL HORNO MICROONDAS

NOTA: cuando instale el horno microondas, ease el cable elctrico a travs del agujero correspondiente de la superficie inferior del gabinete superior Mantengalo tenso recto durante los pasos 1 a 3. No permita que el cable quede atrapado ni levante el horno tirando del cable.

Inserte un tornillo autoalineante a travs del agujero del centro del gabinete superior. Fije temporalmente el horno apretando el tornillo al menos dos vueltas completas despus de due el tornillo quede enroscado. (Ms adelante se proceder a apretar completamente el tornillo.)Asegrese de mantener tenso/recto el cable elctrico. Tenga cuidado de evitar que el cable quede atrapado, especialmente al realizar la instalacin del horno a ras contra la superficie inferior del gabinete.

Levante el microondas, inclnelo hacia adelante y enganche las ranuras (situadas en el borde trasero inferior) a las cuatro lengetas inferiores de la placa de instalacin.

Gire la parte delantera del horno hacia arriba, contra la superficie inferior del gabinete.

SP-14

IMPORTANTE:No agarre ni use la manija o el escudo trmico

durante la instalacin. No retire los separadores de cartn entre el escudo trmico y la puerta.

4 Fije el horno microondas al gabinete superior.

7

Parte delantera del gabinete

Estante inferior del gabinete

Bloque de relleno

Parte superior del horno microondas

Instrucciones de instalacin

Parte trasera del microondasPlaca del ventilador Regulador de extraccin

Tornillo autoalineante

5

A6.A5.

1

2

A7.

Conducto de la cocina

6

INSTALACIN DEL HORNO MICROONDAS (cont.)

Equivalente a la profundidad de la superficie hueca del gabinete

Inserte 2 tornillos autoalineantes a travs de los agujeros exteriores del gabinete superior. Apriete cede uno de los tornillos dos vueltas completas.

Apriete completa- mente el tornillo del centro.

Apriete los dos tornillos externos a la parte superior del horno. (Mientras aprieta los tornillos, mantenga sujeto el horno contra la pared y el gabinete superior)

Extienda el conducto de la cocina para que se acople al adaptador de extraccin. Selle las uniones del conducto de escape usando cinta aislante para calefaccin para altas temperaturas.

AJUSTE DEL ADAPTADOR DE EXTRACCIN

Abra el gabinete superior y ajuste el adaptador de Extraccin para acoplarlo al conducto de la cocina.

Para ajustes en direccin delantera-trasera o lado a lado, deslice el adaptador de extraccin segn sea necesario

ACOPLAMIENTO DEL SISTEMA DE CONDUCTOS

SP-15

8 Instale los filtros de grasa. Consulte el Manual del usuario provisto con el microondas. IMPORTANTE: retire los separadores de cartn entre el escudo

trmico y la puerta

Parte trasera del microondas

Instrucciones de instalacin

B1.

B2.

B

Placa del ventilador

3/8" HASTA EL EXTREMO

ANCHO MNIMO DE 30" REQUERIDO

NOTA: ES MUY IMPORTANTE LEER Y SEGUIR LAS

DIRECCIONES EN LAS INSTRUCCIONES DE INSTALACIN ANTES DE PROCEDER CON ESTA

PLANTILLA DE PARED POSTERIOR. Esta plantilla de la pared posterior sirve para

colocar el plato de montaje inferior y para colocar

la salida de escape horizontal. 1. Use un nivel para cerciorarse de que la plantilla

est colocada de manera apropiada. 2. Localice y marque por lo menos un bajante en

el lado izquierdo o derecho de la lnea central.

NOTA: Es importante usar por lo menos un tornillo

de madera microondas. Marque dos lugares adicionales,

espaciados uniformemente, para los tornillos de palanca

proporcionados.3. Taladre agujeros en los lugares marcados.

Donde exista un bajante, taladre agujeros de 3/16"

para los tornillos de madera. Para los agujeros que no

se alinean con el bajante, taladre agujeros de 5/8"

para los tornillos de palanca.NOTA: NO INSTALE EL PLATO DE MONTAJE EN ESTE MOMENTO.

4. Remueva la plantilla de la pared posterior.

5. Revise el Manual de instrucciones de instalacin para

su situacin de instalacin.

Darle unelta a la hoja para consulta la versin en Espaol.

Localice y marquee los agujeros para que se

alineen con los agujeros en el plato de montaje.

IMPORTANTE:LOCALICE POR LO MENOS UN BAJANTE EN

CUALQUIERA DE LOS LADOS DE LA LINEA CENTRAL.

MARQUE DOS LUGARES ADICIONALES, ESPACIADOS

UNIFORMEMENTE, PARA LOS TORNILLOS DE PALANCA

EN EL REA DEL PLATO DE MONTAJE.

12"

4"

Asegrese de que los tornillos del motor del ventilador y la placa del ventilador queden firmemente apretados al volver a instalarlos. Esto ayudar a prevenir el exceso de vibraciones. Asegrese de que el cableado del motor quede debidamente orientado y asegurado, y que los cables no queden atrapados.

EXTRACCIN TRASERA EXTERNA (Conducto Horizontal)

DESCRIPCIN GENERAL DE LA INSTALACIN B1. Preparacin de la pared trasera B2. Desinstalacin del placa del ventilador B3. Montaje de la placa de instalacin en la pared B4. Preparacin del gabinete superior B5. Ajuste del ventilador B6. Instalacin del horno microondas

NOTAS IMPORTANTES:

Lea las instrucciones de la seccin PLANTILLA PARA LA PARED TRASERA. Adhiera con cinta la plantilla a la pared trasera, alinendola con los agujeros previamente taladrados pares coincidir con los agujeros A y B en la placa para la pared. Realice el corte de la abertura, siguiendo las instrucciones de la seccin PLANTILLA PARA LA PARED TRASERA.

PREPARACIN DE LA PARED TRASERA PARA LA SALIDA DE EXTRACCIN TRASERA EXTERNA

Es necesario realizar un corte en la pared trasera para crear una abertura para la salida de extraccin externa.

DESINSTALACIN DEL PLACA DEL VENTILADOR

Quite y guarde el tornillo que sujeta la placa del ventilador al microondas. Levante la placa del ventilador para retirarla.

Localice y marquee los agujeros para que se

alineen con los agujeros en el plato de montaje.

IMPORTANTE:LOCALICE POR LO MENOS UN BAJANTE EN

CUALQUIERA DE LOS LADOS DE LA LINEA CENTRAL.

MARQUE DOS LUGARES ADICIONALES, ESPACIADOS

UNIFORMEMENTE, PARA LOS TORNILLOS DE PALANCA

EN EL REA DEL PLATO DE MONTAJE.

Corte la plantilla ubicada en la pared de atrs a travs de la linea de puntos

Corte la plantilla ubicada en la pared de atrs a travs de la linea de puntos

CORTE EL AGUJERO A TRAVS DE LA PARED POSTERIOR PARA EL ADAPTADOR DE ESCAPE

PRECAUCIN-SI EL ADAPTADOR DE ESCAPE EST COLOCADO MS

ALL DE LAS DIMENSIONES RECOMENDADAS, AIRE CARGADO CON

GRASA SE DESCARGAR HACIA LA ESTRUCTURA DE LA CASA.

SP-16

3/8" TO EDGE

NOTE: IT IS VERY IMPORTANT TO

READ AND FOLLOW THE DIRECTIONS

IN THE INSTALLATION INSTRUCTIONS

BEFORE PROCEEDING WITH THIS

REAR WALL TEMPLATE.

This Rear Wall Template serves to position the bottom

mounting plate and to locate the horizontal exhaust

outlet. 1. Use a level to check that the template is positioned

accurately. 2. Locate and mark at least one stud on the left or

right side of the centerline.

It is important to use at least one wood

screw mounted firmly in a stud to support the weight

of the microwave. Mark two additional, evenly spaced

locations for the supplied toggle bolts.

3. Drill holes in the marked locations. Where there is

a stud, drill a 3/16" hole for wood screws. For holes

that do not line up with a stud, drill 5/8" holes for

toggle bolts. DO NOT INSTALL THE MOUNTING PLATE

AT THIS TIME.

4. Remove the template from the rear wall.

5. Review the Installation Instruction book for your

installation situation.

Locate and mark holes to align with holes in the

mounting plate.

IMPORTANT:

LOCATE AT LEAST ONE STUD ON EITHER SIDE OF

THE CENTERLINE.

MARK THE LOCATION FOR 2 ADDITIONAL, EVENLY

SPACED TOGGLE BOLTS IN THE MOUNTING PLATE

AREA. Locate and mark holes to align with holes in the

mounting plate.

IMPORTANT:

LOCATE AT LEAST ONE STUD ON EITHER SIDE OF

THE CENTERLINE.

MARK THE LOCATION FOR 2 ADDITIONAL, EVENLY

SPACED TOGGLE BOLTS IN THE MOUNTING PLATE

AREA. Trim the rear wall template along the dotted line.

Trim the rear wall template along the dotted line.

12"

4"

Darle vuelta a la hoja para consultar la

versin en Espaol.

IMPORTANTE: no retire los separadores de

cartn entre el escudo trmico y la puerta.

B3. B4.

Pared

Placa de instalacin

El espacio que ocupan los tornillos fiadores es superior al grueso de la pared

Tornillo fiador

Tuercas de mariposa

Para utilizar tornillos de fiador:

Extremo de tornillo

Instrucciones de instalacin

1

2

3

4

2

1

B5.

Extremo B

Extremo A

Parte trasera del microondas

Motor del ventilador

Tornillo del motor del ventilador

Fije la placa en la pared con los tornillos de fiador. Al menos un tornillo para madera debe ser utilizado para fijar la placa a una viga de la pared.

MONTAJE DE INSTALACIN LA PLACA DE EN LA PARED

Quite las tuercas de mariposa de los tornillos.

Inserte los tornillos en la placa de instalacin, a travs de los agujeros taladrados en las partes de la pared que no son viga (los paneles) y vuelva a insertar las tuercas de mariposa hasta 3/4" (19 mm) de cada tornillo.

Coloque la placa de instalacin contra la pared e inserte las tuercas de mariposa en los agujeros de la pared, a fin de instalar la placa.

NOTA: antes de apretar los tornillos de fiador y el tornillo para madera, asegrese de que las lengetas de la placa de instalacin toquen la parte inferior del gabinete cuando sear empujadas a ras contra la pared, y que la placa quede debidamente centrada bajo el gabinete. PRECAUCIN: tenga cuidado de evitar que sus dedos queden atrapados entre la parte trasera de la placa de instalacin y la pared.

Apriete todos los tornillos. Tire de la placa alejndola de la pared, a fin de que resulte ms fcil apretar los tornillos.

Lea las instrucciones de la seccin PLANTILLA PARA EL GABINETE SUPERIOR. Adhiera con cinta la plantilla al gabinete superior. Taladre los agujeros, siguiendo las instrucciones de la seccin PLANTILLA PARA EL GABINETE SUPERIOR.

USO DE LA PLANTILLA PARA EL GABINETE SUPERIOR A FIN DE PREPARAR EL AREA DE DICHO GABINETE

Es necesario taladrar agujeros para los tomillos de soporte superior, as como un agujero lo suficientemente, grande para que el cable elctrico pueda pasar a travs.

PRECAUCIN: cuando taladre los agujeros en la superficie inferior del gabinete, use gafas protectoras.

AJUSTE DEL VENTILADOR DEL MICROONDAS PARA LA EXTRAC- CIN TRASERA EXTERNA

Quite y guarde el tornillo que sujeta el motor del ventilador al microondas.

Tire del ventilador con cuidado hacia afuera. Los cables se extendern to suficiente para permitir el ajuste del ventilador.

ANTES: aberturas de las aletas del ventilador orientadas hacia adelante

SP-17

Vuelva a colocar el ventilador dentro de su abertura.B5.

Gire el ventilador hacia la izquierda 180.

Antes del giro Despus del giro

Antes de la reorientacin Despus de la reorientacin

Cables orientados a travs del lado derecho

Cables orientados a travs del lado izquierdo

Parte trasera del microondas

Parte trasera del microondas

Placa del ventilador

Tornillo del motor del ventilador

Fije el ventilador al microondas con su tornillo original.

Antes del giro Despus del giro

Parte trasera del microondas

Extremo A

Extremo B

Parte trasera del microondas

Parte trasera del microondas

Instrucciones de instalacin

Gua

Gua

Adaptador

Lengetas de bloqueo

Parte trasera del microondas

Parte trasera del microondas

Gire el ventilador 90.

Parte trasera del microondas

3

4

5

6

7

8

9

10

Antes del giro Despus del giro

B5. 3. o

Parte trasera del microondas 4. o.

Parte trasera del microondas Parte trasera del microondas 5.

6.

Parte trasera del microondas

AJUSTE DEL VENTILADOR DEL MICROONDAS PARA LA EXTRAC- CIN TRASERA EXTERNA (cont.)

Retire suavemente los cables de las ranuras. Reoriente los cables a travs de las ranuras hacia el otro lado del ventilador.

Gire el ventilador 90 , de manera que las aberturas de las aletas del ventilador queden orientadas hacia la parte trasera del microondas.

Vuelva a fijar (con el tornillo) la placa del ventilador en la misma posicin en que estaba antes. Asegrese de que el tornillo quede apretado.

Instale el adaptador de extraccin en la parte trasera del horno, deslizndolo por las guas situadas en la parte central superior de la parte trasera del horno.

Empuje hacia adentro hasta que encaje en las lengetas de bloqueo inferiores. Tenga cuidado de asegurarse de que la bisagra del regulador de extraccin est instalada de manera que quede en la parte superior y que se pueda mover libremente.

DESPUS: Aberturas de las aletas del ventilador orientadas hacia atrs.

PRECAUCIN: No tire hacia afuera ni estire los cables del ventilador. Asegrese de que los cables no queden atrapados y que queden debidamente asegurados. NOTA: Las aberturas de extraccin del ventilador deben coincidir con las aberturas de extraccin situadas en la parte trasera del horno.

SP-18

Instrucciones de instalacin

3

B6.

2

1

Gire la parte delantera del horno hacia arriba, contra la superficie inferior del gabinete.

INSTALACIN DEL HORNO MICROONDAS

POR RAZONES DE SEGURIDAD PERSONAL Y PARA FACILITAR LA INSTALACIN, SE RECOMIENDA QUE DOS PERSONAS INSTALEN EL HORNO MICROONDAS.

NOTA: Si el gabinete es metlico, use una moldura aislante de nylon alrededor del agujero para el cable elctrico, a fin de evitar cortes en el cable. NOTA: Se recomienda el uso de bloques de relleno si la parte delantera del gabinete sobresale debajo del estante inferior del gabinete. IMPORTANTE: Si no se usan bloques de relleno, pueden producirse daos en la carcasa por apretar demasiado los tornillos.

NOTA: cuando instale el horno microondas, pase el cable elctrico a travs del agujero correspondiente de la superficie inferior del gabinete superior: Mantngalo tenso/recto durante los pasos 1 a 3. No permita que el cable quede atrapado ni levante el horno tirando del cable.

Levante el microondas, inclnelo hacia adelante y enganche las ranuras (situadas en el borde trasero inferior) a las cuatro lengetas inferiores de la placa de instalacin.

Inserte un tornillo autoalineante a travs del agujero del centro del gabinete superior: Fije temporalmente el horno apretando el tornillo al menos dos vueltas completas despiss de que el tornillo quede enroscado. (Ms adelante se proceder a apretar completamente el tornillo.) Asegrese de mantener tenso/recto el cable elctrico. Tenga cuidado de evitar que el cable quede atrapado, especialmente al realizar la instalacin del horno a ras contra la superficie inferior del gabinete.

4 Fije el horno microondas al gabinete superior.

7

Parte delantera del gabinete

Estante inferior del gabinete

Bloque de relleno

Parte superior del horno microondas

Tornillo autoalineante

5

6

Equivalente a la profundidad de la superficie hueca del gabinete

Inserte 2 tornillos autoalineantes a travs de los agujeros exteriores del gabinete superior. Apriete cede uno de los tornillos dos vueltas completas.

Apriete completa- mente el tornillo del centro.

Apriete los dos tornillos externos a la parte superior del horno. (Mientras aprieta los tornillos, mantenga sujeto el horno contra la pared y el gabinete superior)

SP-19

8 Instale los filtros de grasa. Consulte el Manual del usuario provisto con el microondas.

IMPORTANTE: retire los separadores de cartn entre el escudo trmico y la puerta

IMPORTANTE:No agarre ni use la manija o el escudo trmico durante la instalacin. No retire los separadores de cartn entre el escudo trmico y la puerta.

Instrucciones de instalacin

C1. 1

2

C

GabineteGabinete

NOTAS IMPORTANTES:

RECIRCULACIN (Sin Conducto De Extraccin)

DESCRIPCIN GENERAL DE LA INSTALACIN C1. Montaje de la placa de instalacin en la pared C2. Preparacin del gabinete superior C3. Verificacin del conjunto del Placa del Ventilador C4. Instalacin del horno microondas C5. lnstalacin o cambiar del filtro de carbn

Asegrese de que los tornillos del motor del ventilador y la placa del ventilador queden firmemente apretados al volver a instalarlos. Esto ayudar a prevenir el exceso de vibraciones. Asegrese de que el cableado del motor quede debidamente orientado y asegurado, y que los cables no queden atrapados.

Fije la placa en la pared con los tornillos de fiador. Al menos un tornillo para madera debe ser utilizado para fijar la placa a una viga de la pared.

MONTAJE DE LA PLACA DE INSTALACIN EN LA PARED

NOTA: Si la profundidad del gabinete incluyendo las puertas es mayor de 13 entonces la unidad debe alejarse de la pared con materiales adecuados que soporten 150 lbs para permitir una ventilacin adecuada/ .

Quite las tuercas de mariposa de los tornillos.

Inserte los tornillos en la placa de instalacin, a travs de los agujeros taladrados en las partes de la pared que no son viga (los paneles) y vuelva a insertar las tuercas de mariposa hasta 3/4 (19 mm) de cada tornillo.

3

4

Pared

Mounting Plate

El espacio que ocupan los tornillos fiadores es superior al grueso de la pared

Extremo de tornillo

Tornillo fiador

Tuercas de mariposa

Para utilizar tornillos de fiador:

Coloque la placa de instalacin contra la pared e inserte las tuercas de mariposa en los agujeros de la pared, a fin de instalar la placa.

NOTA: Antes de apretar los tornillos de fiador y el tornillo para madera, asegrese de que las lengetas de la placa de instalacin toquen la parte inferior del gabinete cuando sean empujadas a ras contra la pared, y que la placa quede debidamente centrada bajo el gabinete. PRECAUCIN: Tenga cuidado de evitar que sus dedos queden atrapados entre la parte trasera de la placa de instalacin y la pared.

Apriete todos los tornillos. Tire de la placa alejndola de la pared, a fin de que resulte ms fcil apretar los tornillos.

toma de aire

SP-20

3/8" TO EDGE

NOTE: IT IS VERY IMPORTANT TO

READ AND FOLLOW THE DIRECTIONS

IN THE INSTALLATION INSTRUCTIONS

BEFORE PROCEEDING WITH THIS

REAR WALL TEMPLATE.

This Rear Wall Template serves to position the bottom

mounting plate and to locate the horizontal exhaust

outlet. 1. Use a level to check that the template is positioned

accurately. 2. Locate and mark at least one stud on the left or

right side of the centerline.

It is important to use at least one wood

screw mounted firmly in a stud to support the weight

of the microwave. Mark two additional, evenly spaced

locations for the supplied toggle bolts.

3. Drill holes in the marked locations. Where there is

a stud, drill a 3/16" hole for wood screws. For holes

that do not line up with a stud, drill 5/8" holes for

toggle bolts. DO NOT INSTALL THE MOUNTING PLATE

AT THIS TIME.

4. Remove the template from the rear wall.

5. Review the Installation Instruction book for your

installation situation.

Locate and mark holes to align with holes in the

mounting plate.

IMPORTANT:

LOCATE AT LEAST ONE STUD ON EITHER SIDE OF

THE CENTERLINE.

MARK THE LOCATION FOR 2 ADDITIONAL, EVENLY

SPACED TOGGLE BOLTS IN THE MOUNTING PLATE

AREA. Locate and mark holes to align with holes in the

mounting plate.

IMPORTANT:

LOCATE AT LEAST ONE STUD ON EITHER SIDE OF

THE CENTERLINE.

MARK THE LOCATION FOR 2 ADDITIONAL, EVENLY

SPACED TOGGLE BOLTS IN THE MOUNTING PLATE

AREA. Trim the rear wall template along the dotted line.

Trim the rear wall template along the dotted line.

12"

4"

Darle vuelta a la hoja para consultar la

versin en Espaol.

IMPORTANTE: no retire los separadores de

cartn entre el escudo trmico y la puerta.

Instrucciones de instalacin

C3.

C4.

Placa del Ventilador

C2.

Lea las instrucciones de la seccin PLANTILLA PARA EL GABINETE SUPERIOR. Adhiera con cinta la plantilla al gabinete superior.

USO DE LA PLANTILLA PARA EL GABINETE SUPERIOR A FIN DE PREPARAR EL REA DE DICHO GABINETE

Es necesario taladrar agujeros para los tornillos de soporte superior, as como un agujero lo suficientemente grande para que el cable elctrico pueda pasar a travs.

NOTA: Ajuste la placa superior de acuerdo a si el microondas est siendo separado de la pared debido a la profundidad del gabinete (ms de 13'').

Taladre los agujeros, siguiendo las instrucciones de la seccin PLANTILLA PARA EL GABINETE SUPERIOR.

PRECAUCIN: cuando taladre los agujeros en la superficie inferior del gabinete, use gafas protectoras.

Coloque el microondas en posicin vertical, con la parte superior hacia arriba. Chequear siel placa del ventilador est instalado correcta- mente en el horno.

VERIFICACIN DEL CONJUNTO DEL PLACA DEL VENTILADOR

INSTALACIN DEL HORNO MICROONDAS

1

Gire la parte delantera del horno hacia arriba, contra la superficie inferior del gabinete.

POR RAZONES DE SEGURIDAD PERSONAL Y PARA FACILITAR LA INSTALACIN, SE RECOMIENDA QUE DOS PERSONAS INSTALEN EL HORNO MICROONDAS.

NOTA: Si el gabinete es metlico, use una moldura aislante de nylon alrededor del agujero para el cable elctrico, a fin de evitar cortes en el cable. NOTA: Se recomienda el uso de bloques de relleno si la parte delantera del gabinete sobresale debajo del estante inferior del gabinete.

NOTA: cuando instale el horno microon- das, pase el cable elctrico a travs del agujero correspondiente de la superficie inferior del gabinete superior: Mantn- galo tenso/recto durante los pasos 1 a 3. No permita que el cable quede atrapado ni levante el horno tirando del cable.

Levante el microondas, inclnelo hacia adelante y enganche las ranuras (situadas en el borde trasero inferior) a las cuatro lengetas inferiores de la placa de instalacin.

Inserte un tornillo autoalineante a travs del agujero del centro del gabinete superior: Fije temporalmente el horno apretando el tornillo al menos dos vueltas completas despiss de que el tornillo quede enroscado. (Ms adelante se proceder a apretar completamente el tornillo.) Asegrese de mantener tenso/recto el cable elctrico. Tenga cuidado de evitar que el cable quede atrapado, especial- mente al realizar la instalacin del horno a ras contra la superficie inferior del gabinete.

4 Fije el horno microondas al gabinete superior.

Parte delantera del gabinete

Estante inferior del gabinete

Bloque de relleno

Parte superior del horno microondas

Tornillo autoalineante

Equivalente a la profundidad de la superficie hueca del gabinete

3

2

IMPORTANTE: Si no se usan bloques de relleno, pueden producirse daos en la carcasa por apretar demasiado los tornillos.

SP-21

IMPORTANTE:No agarre ni use la manija o el escudo trmico durante la instalacin. No retire los separadores de cartn entre el escudo trmico y la puerta.

5

7

C4.

C5.

6

5

4

3

2

1

6

Instrucciones de instalacin

INSTALACIN DEL HORNO MICROONDAS (cont.)

Inserte 2 tornillos autoalineantes a travs de los agujeros exteriores del gabinete superior. Apriete cada uno de, los tornillos dos vueltas completas.

Apriete completa- mente el tornillo del centro.

Apriete los dos tornillos externos a la parte superior del horno. (Mientras aprieta los tornillos, mantenga sujeto el horno contra la pared y el gabinete superior:)

Instalacin o cambiar del filtro de carbn (Algunos Modelos)

NOTA: El filtro de carbn est instalado de fbrica en algunos modelos. Consulte la seccin Uso y cuidado para ver si su dispositivo lo tiene y para leer informacin sobre su remplazo. Siga las instrucciones para remplazar o instalar un filtro de carbn.

Desconecte el microondas del suministro elctrico.

Abra la puerta del microondas y saque los dos tornillos de montaje de ventilacin ubicados en la parte superior del horno con un destornillador Phillips #1.

hacia adelante. Levntelo para sacarlo.

Instale el filtro de carbn. Coloque el filtro en la parte de atrs de la grilla con la cara oscura hacia arriba.

Reinstale el ducto deslizando la parte inferior del mismo hacia su lugar. Empuje la parte superior en su posicin y deslicela hacia la derecha. Remplace los dos tornillos ubicados en la parte superior utilizando un destornillador Phillips #1.

Cierre la puerta del microondas. Enchgelo o reconecte la energa elctrica.

Lengetas Filtro de carbn.

Incline

SP-22

8 Instale los filtros de grasa. Consulte el Manual del usuario provisto con el microondas.

IMPORTANTE: retire los separadores de cartn entre el escudo trmico y la puerta

2.

1.

ANTES DE USAR EL HORNO MICROONDAS

INSTRUCCIONES

DE INSTALACIN

3.

Instrucciones de instalacin

4.

7.

6.

INSTRUCCIONES

DE INSTALACIN

GUA DE USO

Y CUIDADO

REGISTRO DEL

PRODUCTO

Lea el manual de use y cuidado.

Vuelva a colocar el fusible correspondiente o encienda de nuevo el disyuntor.

5.

.8

CONSERVE LAS INSTRUCCIONES DE INSTALACIN PARA USO DEL INSPECTOR LOCAL.

LIENE LA TARJETA DE REGISTRO DEL PRODUCTO.

Asegrese de que el horno microondas haya sido instalado segn las instrucciones.

Retire todo el material de empaque del horno microondas.

Instale el anillo y el plato giratorio en el interior del horno.

Conecte el cable de alimentacin a un tomacorriente exclusivo (dedicado) de 15 a 20 amperios.

Antes de usar el electrodomestico verifique la puesta a tierra del tomacorriente

SP-23

Impreso en China

2 /

1 - 4

3/ 8

3/ 8

13-3/8 8-1/4

2

12-1/2

6-1/4

2 3

/ 7 2

- 9

4

/ 1

- 4

3/ 8

13-3/8

3/8" HASTA EL EXTREMO

ANCHO MNIMO DE 30" REQUERIDO

Corte la plantilla ubicada en la pared de atrs a travs de la linea de puntos.

Corte la plantilla ubicada en la pared de atrs a travs de la linea de puntos.

CORTE EL AGUJERO A TRAVS DE LA PARED POSTERIOR PARA EL ADAPTADOR DE ESCAPE

12"

4"

Parte N: 316902912

Parte N: 316902475

NOTA: ES MUY IMPORTANTE LEER Y SEGUIR LAS DIRECCIONES EN LAS INSTRUCCIONES DE INSTALACIN ANTES DE PROCEDER CON ESTA PLANTILLA DE PARED POSTERIOR. Esta plantilla de la pared posterior sirve para colocar el plato de montaje inferior y para colocar la salida de escape horizontal. 1. Use un nivel para cerciorarse de que la plantilla est colocada de

manera apropiada. 2. Localice y marque por lo menos un bajante en el lado izquierdo o

derecho de la lnea central.

NOTA: Es importante usar por lo menos un tornillo de madera microondas. Marque dos lugares adicionales, espaciados uniformemente, para los tornillos de palanca proporcionados. 3. Taladre agujeros en los lugares marcados. Donde exista un bajante,

taladre agujeros de 3/16" para los tornillos de madera. Para los agujeros que no se alinean con el bajante, taladre agujeros de 5/8" para los tornillos de palanca.

NOTA: NO INSTALE EL PLATO DE MONTAJE EN ESTE MOMENTO. 4. Remueva la plantilla de la pared posterior. 5. Revise el Manual de instrucciones de instalacin para su situacin de

instalacin.

Localice y marquee los agujeros para que se alineen con los agujeros en el plato de montaje. IMPORTANTE: LOCALICE POR LO MENOS UN BAJANTE EN CUALQUIERA DE LOS LADOS DE LA LINEA CENTRAL. MARQUE DOS LUGARES ADICIONALES, ESPACIADOS UNIFORMEMENTE, PARA LOS TORNILLOS DE PALANCA EN EL REA DEL PLATO DE MONTAJE.

F. CORTE PARA EL ESCAPE HORIZONTAL EXTERNO

PRECAUCIN-SI EL ADAPTADOR DE ESCAPE EST COLOCADO MS ALL DE LAS DIMENSIONES RECOMENDADAS, AIRE CARGADO CON GRASA SE

DESCARGAR HACIA LA ESTRUCTURA DE LA CASA.

Localice y marquee los agujeros para que se alineen con los agujeros en el plato de montaje. IMPORTANTE: LOCALICE POR LO MENOS UN BAJANTE EN CUALQUIERA DE LOS LADOS DE LA LINEA CENTRAL. MARQUE DOS LUGARES ADICIONALES, ESPACIADOS UNIFORMEMENTE, PARA LOS TORNILLOS DE PALANCA EN EL REA DEL PLATO DE MONTAJE.

1. Determine qu tipo de rea tiene la superficie inferior del gabinete: hueca o lisa/plana. Vea la figura 1. Si se trata de una superficie inferior lisa, adhiera con cinta la plantilla a dicha superficie (figura 2). Si se trata de una superficie hueca, corte los bordes de la plantilla para que se ajusten a la superficie inferior hueca del gabinete. Es importante que los bordes de los gabinetes permitan una instalacin nivelada del horno. NOTA: En el caso de algunos gabinetes a veces existe un pequeo soporte o bloque pegado entre la parte saliente y la parte inferior de la superficie inferior del gabinete. Corte la plantilla para que se ajuste al soporte o el bloque, a fin de que la plantilla quede lisa y a ras contra la superficie inferior del gabinete. Adhiera con cinta la plantilla para el gabinete superior a la parte inferior del gabinete en el rea hueca (figura 3). NOTA: Tras cortar los bordes de la plantilla, asegurese de que la parte trasera de la plantilla toque la pared trasera (en el caso de gabinetes con superficie inferior lisa/plana) o la parte trasera de la superficie hueca (en el caso de gabinetes con superficie inferior hueca).

NOTA: ES MUY IMPORTANTE LEER Y SEGUIR LAS INSTRUCCIONES DE INSTALACIN ANTES DE PROCEDER A USAR ESTA PLANTILLA PARA EL GABINETE SUPERIOR. Esta plantilla se usa para ubicar el agujero a traves del cu al pasar el cable elctrico, los agujeros para la instalacin en el gabinete y el hueco para la salida de extraccin vertical.

2. Taladre agujeros con dimetro de 3/8" en A., 8. y C. PRECAUCIN: cuando taladre los agujeros en la superficie inferior del gabinete, use gafas protectoras.

3. Realice el corte para el agujero (hueco) con dimetro de 2"en D. para el cable elctrico. Si el gabinete es metlico, use una moldura aislante de nylon alrededor del agujero para el cable elctrico, a fin de evitar cortes en el cable (consulte la seccin de piezas incluidas del Manual de instrucciones de instalacin).

4. (SOLAMENTE PARA EXTRACCIN VERTICAL) Corte el rea sombreada E. a traves de la superficie inferior del gabinete, para la ubicacin de la salida de extraccin vertical (externa).

5. Retire la plantilla para el gabinete superior. 6. En el caso de gabinetes con superficie inferior

hueca, confeccione 2 bloques de relleno con madera sobrante, del tamano de las reas sombreadas F y G. Dichos bloques de relleno deben tener un espesor igual a la profundidad del hueco del gabinete. Taladre agujeros con un dimetro de 1/2" en dichos bloques, para alinearlos con A. y C. Coloque los bloques de manera que los agujeros en cada bloque queden alineados con los correspondientes agujeros en el gabinete. Los bloques de relleno deben quedar al mismo nivel que el borde inferior del marco del gabinete en la pared (figura 4).

7. PROSIGA CON LAS INSTRUCCIONES DE INSTALACIN.

PLANTILLA PARA EL GABINETE SUPERIOR

E. HUECO PARA EXTRACCIN VERTICAL (EXTERNA) SOLAMENTE

CORTE EL AGUJERO A TRAVES DEL ADAPTADOR DE EXTRACCIN PARA LA SUPERFICIE INFERIOR DEL GABINETE

DIAMETRO DE TALADRO 2"

D. CABLE ELCTRICO

DIMETRO DE TALADRO 3/8"

GABINETE SUPERIOR

BLOQUES DE RELLENO FIG. 4

GABINETE SUPERIORGABINETE SUPERIOR GABINETE SUPERIORGABINETE SUPERIOR

Parte inferior procesada del gabinete

Gabinete con parte inferior lisa

G .

REA D

EL BLO Q

U E

D E RELLEN

O

DIAMETRO DE TALADRO 3/8"

ParedPared

DIAMETRO DE TALADRO 3/8"

F.

RE A

D EL

B LO

Q U

E D

E RE

LL EN

O

Turn over for English

SP-24PN: 16170000A10767

Instructions dinstallation

Four micro-ondes hotte intgre

Lisez attentivement toutes ces instructions.

IMPORTANT Conservez ces instructions pour linspecteur local.

IMPORTANT Respectez tous les codes et rglements en vigueur.

Remarque destine linstallateur Assurez- vous de laisser ces instructions au consommateur.

Remarque destine au consommateur Conservez ces instructions pour vous y reporter ultrieurement. Niveau de comptence Linstallation de cet appareil ncessite des comptences de base en mcanique et en lectricit. Linstallateur est responsable de la qualit de linstallation. Une panne cause par une mauvaise installation nest pas couverte par la garantie du produit.

VEUILLEZ LIRE ATTENTIVEMENT. CONSERVEZ CES INSTRUCTIONS.

AVANT DE COMMENCER

Des questions? Appelez au ou

p/n 316495163

1-877-435-3287(US) 1-800-265-8352(Canada)

Aot 2015

Instructions dinstallation

INDEX: Renseignements gnraux

Guide dinstallation tape par tape

B

A

C

vacuation lextrieur par le dessus ...........................12-15

vacuation lextrieur par larrire ..............................16-19

Recyclage dair ..............................................................20-22

6-8Installation de la plaque de montage ......................................

Mesures de scurit importantes ...............................................3

Exigences lectriques ...................................................................3

Dommages - Expdition/installation ..........................................4

Pices comprises ..........................................................................4

Outils ncessaires..........................................................................5

Dgagements pour linstallation .................................................5

Enlvement de la plaque de montage .................................6

Localisation des montants.................................................6

tablissement de lemplacement de la plaque murale.......7

Alignement de la plaque murale .....................................8

Types dinstallation ...............................................................9-22

vacuation de la hotte ............................................................10-11

Fixation de la plaque de montage au mur ........................12

Prparation de larmoire suprieure ..............................13

Ajustement du ventilateur..............................................13-14

Vrification du fonctionnementdu registre .......................14

Installation du four micro-ondes ..............................14-15

Ajustement de ladaptateur dvacuation..........................15

Connexion au conduit ......................................................15

lvacuation lextrieur par larrire ............................16

Enlvement de lplaque du ventilateur................................16

Fixation de la plaque de montage au mur .........................17

Prparation de larmoire suprieure ...............................17

Fixation de la plaque de montage au mur .......................20

Prparation de larmoire suprieure ...............................21

Vrification de lplaque du ventilateur.............................21

Installation du four micro-ondes...............................21-22

Installation ou changemeut du filtre charbon.................22

Avant dutiliser votre four micro-ondes ................................23

L`information de gabarit............................................................24

Adaptation du ventilateur du four micro-ondes pour

lvacuation lextrieur par larrire ........................17-18

Installation du four micro-ondes ..................................19

FR-2

Instructions dinstallation

Ce produit ncessite une prise de courant trois alvoles mise la terre. Avant dentreprendre linstallation, linstallateur doit vrifier la continuit de la mise la terre de la bote de la prise de courant pour sassurer que cette dernire est correctement mise la terre. Si ce nest pas le cas, ou si la bote ne rpond pas aux exigences lectriques indiques ( la section EXIGENCES LECTRIQUES), il faut faire appel un lectricien qualifi pour corriger tout

dfaut.

ATTENTION: Pour votre scurit, enlevez le fusible ou dclenchez le disjoncteur au panneau de distribution principal avant dentreprendre linstallation, afin dviter toute blessure grave ou mortelle imputable un choc lectrique.

ATTENTION : Pour votre scurit, la surface de montage doit tre en mesure de supporter la charge des armoires, ainsi quun poids supplmentaire de 28,5 38,5 kg (63 85 lb) correspondant au poids du produit, et la charge du four qui peut atteindre 22,7 kg (50 lb), pour un poids total de 51,3 61,2 kg (113 135 lb).

ATTENTION : Pour votre scurit, ce produit ne doit pas tre install avec des armoires amnages en lot ou en pninsule. Il doit tre fix LA FOIS une armoire suprieure ET un mur.

REMARQUE : Pour faciliter linstallation et pour votre scurit, linstallation de ce produit doit tre effectue par deux personnes.

IMPORTANT VEUILLEZ LIRE ATTENTIVEMENT. POUR VOTRE SCURIT, CET APPAREIL DOIT TRE CORRECTEMENT MIS LA TERRE POUR VITER UN CHOC GRAVE OU MORTEL.

Pour diminuer les risques de choc lectrique, le cordon dalimentation de cet appareil est muni dune fiche trois broches (mise la terre) qui correspond une prise murale trois alvoles, mise la terre.

MESURES DE SCURIT IMPORTANTES

Assurez-vous quune mise la terre approprie est en place avant toute utilisation

Demandez un lectricien qualifi de vrifier la prise murale et le circuit lectrique pour vous assurer que la prise est correctement mise la terre.

Si la prise murale est du type standard deux alvoles, il est trs important de la faire remplacer par une prise trois alvoles correctement mise la terre en vous adressant un lectricien qualifi.

NE COUPEZ, NE DFORMEZ ET NE RETIREZ EN AUCUN CAS UNE DES BROCHES DE LA FICHE DU CORDON DALIMENTATION. NUTILISEZ PAS DE RALLONGE.

EXIGENCES LECTRIQUES Les caractristiques nominales de ce produit sont : 120 V CA, 60 Hz, 15 A et 1,6 kW. Ce produit doit tre branch un circuit dalimentation

s par e et d di e

de tension et de frquence appropries. La grosseur des fils doit tre conforme aux exigences du Code national dlectricit ou du code local en vigueur pour cette puissance nominale. La fiche du cordon dalimentation doit tre branche dans une prise de courant mise la terre, de 15 ou 20 ampres. La bote

dalimentation doivent tre installs par un lectricien qualifi, conformment aux normes du Code national dlectricit ou du code local en vigueur.

FR-3

de la prise doit tre amnage dans larmoire situe au-dessus du four micro-ondes. La bote de la prise et le circuit

s par e et d di e

Instructions dinstallation

DOMMAGES EXPDITION/ INSTALLATION

Si lappareil est endommag durant le transport , retournez-le au magasin o vous lavez achet pour rparation ou remplacement.

Si lappareil est endommag par le client, la rparation ou le remplacement reste la charge du client.

Si lappareil est endommag par linstallateur (sil sagit dune personne diffrente du client), la rparation ou le remplacement doivent faire lobjet dune entente entre le client et linstallateur.

Vous trouverez les pices de quincaillerie dans un sachet fourni avec lappareil. Vrifiez que vous avez reu toutes ces pices.

REMARQUE: Des pices supplmentaires sont incluses.

PICES COMPRISES

SACHET DE QUINCAILLERIE QUANTITPICE

Vis bois (1/4 x 2 po)

Boulons ailettes (et crous oreilles) (3/16 x 3 po)

Vis mtaux auto-alignement (1/4 po - 28 x 3-1/4 po)

Passe-fil en nylon (pour armoires en mtal)

2

3

2

1

PICE QUANTIT

Instructions dinstallation

Filtres graisses emballs sparment

1

1

2

INSTRUCTIONSDINSTALLATION

PICES COMPRISES (SUITE)

SACHET DE QUINCAILLERIE

1 Adaptateur de conduit dvacuation

1Plateau en verre

1Anneau de plateau tournant

Gabarit pour armoire suprieure

Gabarit po ur mur arrire combin

1

Mode demploi etdentretien

Mode demploi 1et dentretien

1

Trpied

Etagre

mtallique de convection

2

FR-4

Pour certains modles

Pour certains modles

Instructions dinstallation

DGAGEMENTS POUR LINSTALLATION

Tournevis Phillips n

Rgle ou ruban mesurer et rgle droite

querre de menuisier (facultative)

Cisailles de ferblantier (pour couper le registre, si ncessaire) Ciseaux (pour couper le

gabarit, si ncessaire) Perceuse lectrique avec forets de 3/16, 1/2 et 5/8 po

Crayon

Gants

Lunettes de scurit

30 po (76,2 cm)

min.

Dosseret

30 po (76,2 cm)

2 po (5,1 cm)

Au moins 66 po (167,6 cm) entre le sol et le dessus du four micro-ondes

Rebord infrieur de larmoire 30 po

(76,2 cm) minimum de la surface

de cuisson

Scie (sauteuse, trpan ou guichet) Localisateur de montant

Marteau (facultatif)

Niveau Ruban adhsif en toile et ruban-cache

Entretoises dassemblage ou pices de bois de rcupration, si besoin est, pour lespacement avec larmoire suprieure (utilises pour linstallation sous une armoire dont le fond est dot dun rebord)

ou

REMARQUES :

armoires, sans obstructions. Si lvacuation de lair de votre four micro-ondes

seffectue vers lextrieur, consultez la section vacuation de la hotte pour la prparation du conduit dvacuation . Lorsque vous installez le four micro-ondes sous des armoires dont le fond est lisse et plat, suivez attentivement les instructions du gabarit pour armoire

dalimentation.

OUTILS NCESSAIRES

13 p (33 cm) Maximale

rieure concernant le d gagement du cordon

de gabarit montage.

l faut un espace d

au moins 30 po (76,2 cm entre les

Comme un guide d installation, voir page24 pour l information

ArmoireArmoire

Si la profondeur du armoire incluant les portes du armoire est plus de 13 po alors l'unit doit tre espace du mur utilisant des matriaux adquats supportant 150 lbs pour permettre une bonne ventilation d'air au sommet/admission d'air.

FR-5

1 7

1 /2

"p o

(4 4

.6 cm

)

Instructions dinstallation

INSTALLATION DE LA PLAQUE DE MONTAGE1

LOCALISATION DES MONTANTSB.

Localisez les montants en utilisant une des mthodes suivantes : A. Localisateur de montant dispositif

magntique permettant de localiser les clous. B. Utilisez un marteau pour frapper lgrement sur la

surface de montage jusqua ce que vous nentendiez plus un son creux. Cela signifie que vous avez trouv un montant.

Aprs avoir localis le(s) montant(s), trouvez-en le centre en sondant le mur laide dun petit clou afin de trouver les rebords du montant. Puis faites une marque mi-chemin entre les deux bords. Le centre de tout montant adjacent doit se trouver 16 po (40,6 cm) ou 24 po (61 cm) de cette marque.

Tracez une ligne verticale marquant le milieu des montants.

LE FOUR MICRO-ONDES DOIT TRE FIX AU MOINS UN MONTANT DU MUR.

3

2

1

Bote

Polystyrne

Centre

Montants

Tirez la bote vers le haut pour dgager le four.3

ENLEVER LE FOUR MICRO-ONDES DU CARTON/ENLEVER LE PLATEAU DE MONTAGE

Repliez compltement les quatre rabats contre les cts de la bote. Ensuite, retournez le four et la bote avec prcaution. Le four devrait reposer sur le polystyrne.

2

1

A.

Enlevez les instructions de l'installation, utilisez et prenez soin, adaptateur d'chappement, anneau de la plaque tournante, rayon, filtres, plateau de verre et le petit sac de mattiel. N'enlevez pas le polystyrne protgeant l'avant du four.

4

Enlevez les vis de la plaque de montage. Cette plaque sera utilise comme gabarit pour le mur arrire et pour le montage. Remettez en place les vis retires pralablement.

5

Coupez le centre du sac en plastique pour retirer la plaque de montage

Vis Plaque de montage

Vis

Anneau de la plaque tournante sous le plaeau de verre

Adaptateur d'chappementPetit sac de matriel

Plateau de verre

Etagre

FR-6

Instructions dinstallation

Vos armoires peuvent tre dotes de garnitures dcoratives qui entravent linstallation du micro-ondes. Enlevez llment dcoratif pour installer convenablement le four micro-ondes et pour vous assurer quil est de niveau.

LE FOUR MICRO-ONDES DOIT TRE DE NIVEAU. Utilisez un niveau pour vous assurer que le fond de larmoire est de niveau.

Si les armoires sont dotes uniquement dun rebord avant, sans rebord sur les cts ou larrire, installez la plaque de montage plus bas, la mme distance que le rebord avant de larmoire. Ainsi, le four sera de niveau.

Mesurez la hauteur intrieure du rebord avant de larmoire.

Tracez une ligne horizontale sous le fond de larmoire, sur le mur arrire une distance quivalente la longueur intrieure du rebord avant de larmoire.

Pour linstallation sous une armoire dote dun rebord avant uniquement, alignez les languettes de montage sur cette ligne horizontale, sans quelles touchent le fond de larmoire, tel que dcrit ltape D.

3

2

1

TABLISSEMENT DE LEMPLACEMENT DE LA PLAQUE MURALE SOUS VOTRE ARMOIRE

C.

Emplacement de la plaque - sous une armoire fond plat

Emplacement de la plaque - sous une

Emplacement de la plaque - sous une armoire dote dun rebord

Au moins 30 po

C

3/8" TO EDGE

NOTE: IT IS VERY IMPORTANT TO

READ AND FOLLOW THE DIRECTIONS

IN THE INSTALLATION INSTRUCTIONS

BEFORE PROCEEDING WITH THIS

REAR WALL TEMPLATE. This Rear Wall Template serves to position the bottom

mounting plate and to locate the horizontal exhaust

outlet. 1. Use a level to check that the template is positioned

accurately.2. Locate and mark at least one stud on the left or

right side of the centerline.It is important to use at least one wood

screw mounted firmly in a stud to support the weight

of the microwave. Mark two additional, evenly spaced

locations for the supplied toggle bolts.

3. Drill holes in the marked locations. Where there is

a stud, drill a 3/16" hole for wood screws. For holes

that do not line up with a stud, drill 5/8" holes for

toggle bolts. DO NOT INSTALL THE MOUNTING PLATE

AT THIS TIME.4. Remove the template from the rear wall.

5. Review the Installation Instruction book for your

installation situation.

Locate and mark holes to align with holes in the

mounting plate.IMPORTANT:LOCATE AT LEAST ONE STUD ON EITHER SIDE OF

THE CENTERLINE.MARK THE LOCATION FOR 2 ADDITIONAL, EVENLY

SPACED TOGGLE BOLTS IN THE MOUNTING PLATE

AREA.

Locate and mark holes to align with holes in the

mounting plate.IMPORTANT:LOCATE AT LEAST ONE STUD ON EITHER SIDE OF

THE CENTERLINE.MARK THE LOCATION FOR 2 ADDITIONAL, EVENLY

SPACED TOGGLE BOLTS IN THE MOUNTING PLATE

AREA.

Trim the rear wall template along the dotted line.

Trim the rear wall template along the dotted line.

12"

4"

Darle vuelta a la hoja para consultar la

versin en Espaol.

17-1/2

Tracez une ligne verticale sur le mur au centre de l'espace de 30 po de large. Tape gabarit pour mur arrire sur le mur correspondant la ligne mdiane et en touchant le bas de l'armoire.

C

3/8" TO EDGE

NOTE: IT IS VERY IMPORTANT TO

READ AND FOLLOW THE DIRECTIONS

IN THE INSTALLATION INSTRUCTIONS

BEFORE PROCEEDING WITH THIS

REAR WALL TEMPLATE. This Rear Wall Template serves to position the bottom

mounting plate and to locate the horizontal exhaust

outlet. 1. Use a level to check that the template is positioned

accurately.2. Locate and mark at least one stud on the left or

right side of the centerline.It is important to use at least one wood

screw mounted firmly in a stud to support the weight

of the microwave. Mark two additional, evenly spaced

locations for the supplied toggle bolts.

3. Drill holes in the marked locations. Where there is

a stud, drill a 3/16" hole for wood screws. For holes

that do not line up with a stud, drill 5/8" holes for

toggle bolts. DO NOT INSTALL THE MOUNTING PLATE

AT THIS TIME.4. Remove the template from the rear wall.

5. Review the Installation Instruction book for your

installation situation.

Locate and mark holes to align with holes in the

mounting plate.IMPORTANT:LOCATE AT LEAST ONE STUD ON EITHER SIDE OF

THE CENTERLINE.MARK THE LOCATION FOR 2 ADDITIONAL, EVENLY

SPACED TOGGLE BOLTS IN THE MOUNTING PLATE

AREA.

Locate and mark holes to align with holes in the

mounting plate.IMPORTANT: LOCATE AT LEAST ONE STUD ON EITHER SIDE OF

THE CENTERLINE.MARK THE LOCATION FOR 2 ADDITIONAL, EVENLY

SPACED TOGGLE BOLTS IN THE MOUNTING PLATE

AREA.

Trim the rear wall template along the dotted line.

Trim the rear wall template along the dotted line.

12"

4"

Darle vuelta a la hoja para consultar la

versin en Espaol.

30 po de la surface de cuisson

Tracez une ligne verticale sur le mur au centre de l'espace de 30 po de large. Tape gabarit pour mur arrire sur le mur correspondant la ligne mdiane et en touchant le cadre bas de l'armoire.

C

3/8" TO EDGE

NOTE: IT IS VERY IMPORTANT TO

READ AND FOLLOW THE DIRECTIONS

IN THE INSTALLATION INSTRUCTIONS

BEFORE PROCEEDING WITH THIS

REAR WALL TEMPLATE. This Rear Wall Template serves to position the bottom

mounting plate and to locate the horizontal exhaust

outlet. 1. Use a level to check that the template is positioned

accurately.2. Locate and mark at least one stud on the left or

right side of the centerline.It is important to use at least one wood

screw mounted firmly in a stud to support the weight

of the microwave. Mark two additional, evenly spaced

locations for the supplied toggle bolts.

3. Drill holes in the marked locations. Where there is

a stud, drill a 3/16" hole for wood screws. For holes

that do not line up with a stud, drill 5/8" holes for

toggle bolts. DO NOT INSTALL THE MOUNTING PLATE

AT THIS TIME.4. Remove the template from the rear wall.

5. Review the Installation Instruction book for your

installation situation.

Locate and mark holes to align with holes in the

mounting plate.IMPORTANT:LOCATE AT LEAST ONE STUD ON EITHER SIDE OF

THE CENTERLINE.MARK THE LOCATION FOR 2 ADDITIONAL, EVENLY

SPACED TOGGLE BOLTS IN THE MOUNTING PLATE

AREA.

Locate and mark holes to align with holes in the

mounting plate.IMPORTANT:LOCATE AT LEAST ONE STUD ON EITHER SIDE OF

THE CENTERLINE.MARK THE LOCATION FOR 2 ADDITIONAL, EVENLY

SPACED TOGGLE BOLTS IN THE MOUNTING PLATE

AREA.

Trim the rear wall template along the dotted line.

Trim the rear wall template along the dotted line.

12"

4"

Darle vuelta a la hoja para consultar la

versin en Espaol.

3/8" TO EDGE

NOTE: IT IS VERY IMPORTANT TO

READ AND FOLLOW THE DIRECTIONS

IN THE INSTALLATION INSTRUCTIONS

BEFORE PROCEEDING WITH THIS

REAR WALL TEMPLATE. This Rear Wall Template serves to position the bottom

mounting plate and to locate the horizontal exhaust

outlet. 1. Use a level to check that the template is positioned

accurately.2. Locate and mark at least one stud on the left or

right side of the centerline.It is important to use at least one wood

screw mounted firmly in a stud to support the weight

of the microwave. Mark two additional, evenly spaced

locations for the supplied toggle bolts.

3. Drill holes in the marked locations. Where there is

a stud, drill a 3/16" hole for wood screws. For holes

that do not line up with a stud, drill 5/8" holes for

toggle bolts. DO NOT INSTALL THE MOUNTING PLATE

AT THIS TIME.4. Remove the template from the rear wall.

5. Review the Installation Instruction book for your

installation situation.

Locate and mark holes to align with holes in the

mounting plate.IMPORTANT:LOCATE AT LEAST ONE STUD ON EITHER SIDE OF

THE CENTERLINE.MARK THE LOCATION FOR 2 ADDITIONAL, EVENLY

SPACED TOGGLE BOLTS IN THE MOUNTING PLATE

AREA.

Locate and mark holes to align with holes in the

mounting plate.IMPORTANT:LOCATE AT LEAST ONE STUD ON EITHER SIDE OF

THE CENTERLINE.MARK THE LOCATION FOR 2 ADDITIONAL, EVENLY

SPACED TOGGLE BOLTS IN THE MOUNTING PLA

AREA.

Trim the rear wall template along the dotted line.

Trim the rear wall template along the dotted line.

12"

4"

Darle vuelta a la hoja para consultar la

versin en Espaol.

30 po de la surface de cuisson

Tracez une ligne sur le mur arrire gale la profondeur de le surplomb avant

FR-7

Instructions dinstallation

3

2

1

ATTENTION : Portez des gants pour viter de vous blesser sur les bords coupants.

ALIGNEMENT DE LA PLAQUE MURALED.

Tracez une ligne horizontale sur le mur de

La ligne horizontale La ligne horizontaleTrou A

Trou B

Zone E

Encoches de la ligne centrale

"

"

de 30 po de large. Tracez une ligne verticale sur le mur au centre de lespace

d`armoire suprieure

Tracez une ligne verticale sur le mur du Centre

fond de "Gabarit pour mur arrire"

Trouvez un clou du mur dans la zone "E" du plateeau de montage, refrez-vous la section 1B. Trouver les clous du mur.

4 Pour attacher le plateau du montage dans le clou forez un trou de 3/16 po dans le clou en bois. Forez un trou de 5/8 po pour le verrou d'interrupteur bascules dans un autre emplacement (Trou A ou Trou B). REMARQUE : NE FIXEZ PAS LA PLAQUE DE MONTAGE MAINTENANT.

REMARQUE: Les trous A et B sont l'int rieur de la zone E. Si aucun des trous A et B ne se trouve dans un montant, trouvez un montant dans la zone E et tracez un cinquime cercle pour laligner sur un montant. Il est important quau moins une vis bois soit fixe solidement dans un montant pour soutenir le poids du four microondes. Mettez la plaque de montage de ct.

FR-8

Instructions dinstallation

TYPES DINSTALLATION (Choisissez A, B ou C)2 Ce four micro-ondes est conu pour sadapter aux trois types dvacuation suivants : A. vacuation lextrieur par le dessus (conduit vertical) B. vacuation lextrieur par larrire (conduit horizontal) C. Recyclage (sans conduit)

Sur les modles conus pour le recyclage dair, un filtre charbon jetable est install en usine pour retenir la fume et les odeurs.

REMARQUE: Ce four micro-ondes est quip lusine en vue

rendez-vous cette section.

VACUATION LEXTRIEUR PAR LE DESSUS (CONDUIT VERTICAL)

A VACUATION LEXTRIEUR PAR LARRIRE (CONDUIT HORIZONTAL)

B

RECYCLAGE DAIR (VACUATION SANS CONDUIT)

C

Adaptateur en place pour une vacuation lextrieur par le dessus

Consultez la page 12

Ladaptateur doit tre plac larrire pour une vacuation lextrieur par larrire

dune .Recyclage Choisissez le type dvacuation appropri votre installation et

Consultez la page 16

Consultez la page 20

REMARQUE: Ne lisez les deux pages suivantes que si vous dcidez dvacuer lair du ventilateur lextrieur. Si vous dcidez de recycler lair dans la pice, rendez-vous la page 20.

FR-9

Instructions dinstallation

Lvacuation vers lextrieur requiert un CONDUIT DVACUATION POUR HOTTE. Lisez attentivement ce qui suit. REMARQUE: Il est important que lvacuation soit installe en utilisant le chemin le plus direct et avec le moins de coudes possible. Cela assure une bonne vacuation et aide a prvenir les blocages. Assurez-vous galement que les registres bougent librement et que rien ne bloque les conduits. Connexion d'chappement:

Longueur maximale du conduit:

Les coudes, adaptateurs de transition, vents muraux ou de toiture, etc. offrent une rsistance supplmentaire la circulation de lair et sont quivalents une section de conduit droit plus longue que leur dimension relle. Lorsque vous calculez la longueur totale du conduit, ajoutez les longueurs quivalentes de tous les adaptateurs de transition et des coudes, ainsi que la longueur de toutes les sections de conduit droit. Vous trouverez dans le tableau ci-dessous la longueur quivalente approximative en pieds et en mtres de certains types de conduits.

* IMPORTANT: Si vous utilisez un adaptateur de transition, il faudra couper les coins infrieurs du registre aux dimensions de ladaptateur laide de cisailles pour que le registre puisse bouger.

Les longueurs quivalentes des pices de conduits sont bases sur des essais rels et reprsentent les longueurs ncessaires une bonne ventilation pour nimporte quelle hotte.

Longueur totale

LONGUEUR QUIVALENTE

pi ou m

pi ou m

pi ou m

pi ou m

pi ou m

pi ou m

pi ou m

pi ou m

pi ou m

NOMBRE UTILIS

( )

( )

( )

( )

( )

( )

( )

( )

=

=

=

=

=

=

=

=

=

=

x

x

x

x

x

x

x

x

x

LONGUEUR QUIVALENTE

5 pi (1,5 m)

40 pi (12,2 m)

10 pi (3 m)

5 pi (1,5 m)

25 pi (7,6 m)

5 pi (1,5 m)

24 pi (7,3 m)

1 pi (0,3 m)

Adaptateur de transition*

vent mural

Coude de 90

Coude de 45

Coude de 90

Coude de 45

vent de toiture

Conduit droit rond de 6 po (15,2 cm) ou rectangulaire de 3-1/4 x 10 po (8,2 x 25,4 cm)

PICES DE CONDUIT

INSTRUCTIONS POUR L`INSTALLATION EXTERIEURE DE CODUITS D`ECHAPPEMENT.

L'adaptateur d'chappement a t conu pour s'accoupler avec une canalisation rectangulaire standard de 3 1/4 x 10 po (8.2 x 25,4 cm). Si une canalisation ronde est recquise, un adaptateur de transition rectangulaire-rond doit tre utilis. Une canalisation de diamtre 5 po (12,7cm) / 6 po (15,2cm) est acceptable utiliser.

Pour une circulation dair satisfaisante, la longueur totale du conduit rectangulaire de 3-1/4 x 10 po (8,2 x 25,4 cm) ou du conduit rond de 5 po (12,7cm) / 6 po (15,2 cm) de diamtre ne doit pas excder une longueur quivalente 120 pi (36,5m)

REMARQUE : Si vous devez installer des conduits, notez que la longueur totale du conduit rectangulaire de 3-1/4 po x 10 po (8,2 x 25,4 cm) ou du conduit rond de 5 po (12,7cm)/6 po (15,2 cm) de diamtre ne doit pas tre suprieure 120 pi (36,5m) de longueur quivalente.

FR-10

Instructions dinstallation

CANALISATION D'ECHAPPEMENT EXTERNE

VACUATION LEXTRIEUR PAR LE DESSUS (EXEMPLE SEULEMENT) Le tableau suivant dcrit un exemple dinstallation de conduit.

vent de toiture

Conduit droit de 12 pi (3,6 m) (rond de 6 po/15,2 cm)

Adaptateur de transition*

Les longueurs quivalentes des pices de conduits sont bases sur des essais rels et reprsentent les longueurs ncessaires une bonne ventilation pour nimporte quelle hotte.

IMPORTANT: Si vous utilisez un adaptateur de transition, il faudra couper les coins infrieurs du registre aux dimensions de ladaptateur laide de cisailles pour que le registre puisse bouger.

PICES DE CONDUIT LONGUEUR QUIVALENTE

24 pi (7,3 m)

12 pi (3,6 m)

5 pi (1,5 m)

x

x

x

x

=

=

=

=

=

NOMBRE UTILIS

(1)

(1)

(1)

Longueur totale

LONGUEUR QUIVALENTE

24 pi (7,3 m)

12 pi (3,6 m)

5 pi (1,5 m)

41 pi (12,5 m)

vent mural

Conduit droit de 3 pi (0,91 m) (rectangulaire 1/4 x 10 po/ 8,2 x 25,4 cm)

Coude de 90

Les longueurs quivalentes des pices de conduits sont bases sur des essais rels et reprsentent les longueurs ncessaires une bonne ventilation pour nimporte quelle hotte.

REMARQUE :Dans le cas dune vacuation par larrire, veillez aligner le conduit dvacuation sur les espaces entre les montants, ou prparer le mur au moment de la construction en laissant assez despace entre les montants pour recevoir le conduit.

PICES DE CONDUIT LONGUEUR QUIVALENTE

40 pi (12,2 m)

3 pi (0,9 m)

10 pi (3 m)

x

x

x

x

=

=

=

=

=

NOMBRE UTILIS

(1)

(1)

(2)

Longueur totale

LONGUEUR QUIVALENTE

40 pi (12,2 m)

3 pi (0,9 m)

20 pi (6 m)

63 pi (19,2 m)

VACUATION LEXTRIEUR PAR LARRIRE (EXEMPLE SEULEMENT) Le tableau suivant dcrit un exemple dinstallation de conduit.

FR-11

Instructions dinstallation

VACUATION LEXTRIEUR PAR LE DESSUS (Conduit vertical)A

VUE DENSEMBLE DE LINSTALLATION A1. Fixation de la plaque

de montage au mur A2. Prparation de larmoire

suprieure A3.

Vrification du fonctionnement du registre

A4.

Installation du four micro-ondes

A5.

Ajustement de ladaptateur dvacuation

A6.

Connexion au conduit

Pour utiliser les boulons ailettes :FIXATION DE LA PLAQUE DE MONTAGE AU MUR

A1.

Fixez la plaque au mur laide des boulons ailettes. Vous devez utiliser au moins une vis bois pour fixer la plaque un montant.

Enlevez les crous ailettes des boulons.

Insrez les boulons dans la plaque de montage travers les trous dans le gypse et rassemblez les crous ailettes, 3/ 4 po (19 mm) sur chaque boulon.

2

1

Placez la plaque de montage contre le mur et insrez les crous ailettes dans les trous du mur pour fixer la plaque.

REMARQUE: Avant de resserrer les boulons ailettes et la vis bois, assurez-vous que la plaque est bien centre sous larmoire et que les languettes de la plaque de montage touchent le dessous de larmoire lorsque vous poussez la plaque contre le mur. ATTENTION: Faites attention de ne pas vous pincer les doigts entre larrire de la plaque de montage et le mur.

Serrez tous les boulons. Tirez sur la plaque pour faciliter le serrage des boulons.

4

3

Espace pour les ailettes suprieur lpaisseur du mur

crou ailettes Boulon ailettes

Mur Extrmit du boulon

REMARQUES IMPORTANTES : Assurez-vous que les vis du moteur du ventilateur et de la

plaque du ventilateur sont solidement visses lorsque vous les remettez en place. Cela vitera les vibrations excessives.

Assurez-vous que les fils du moteur sont bien achemins, fixs et quils ne sont pas coincs.

A7.

Ajustement du ventilateur

3/8" TO EDGE

NOTE: IT IS VERY IMPORTANT TO

READ AND FOLLOW THE DIRECTIONS

IN THE INSTALLATION INSTRUCTIONS

BEFORE PROCEEDING WITH THIS

REAR WALL TEMPLATE.

This Rear Wall Template serves to position the bottom

mounting plate and to locate the horizontal exhaust

outlet. 1. Use a level to check that the template is positioned

accurately. 2. Locate and mark at least one stud on the left or

right side of the centerline.

It is important to use at least one wood

screw mounted firmly in a stud to support the weight

of the microwave. Mark two additional, evenly spaced

locations for the supplied toggle bolts.

3. Drill holes in the marked locations. Where there is

a stud, drill a 3/16" hole for wood screws. For holes

that do not line up with a stud, drill 5/8" holes for

toggle bolts. DO NOT INSTALL THE MOUNTING PLATE

AT THIS TIME.

4. Remove the template from the rear wall.

5. Review the Installation Instruction book for your

installation situation.

Locate and mark holes to align with holes in the

mounting plate.

IMPORTANT:

LOCATE AT LEAST ONE STUD ON EITHER SIDE OF

THE CENTERLINE.

MARK THE LOCATION FOR 2 ADDITIONAL, EVENLY

SPACED TOGGLE BOLTS IN THE MOUNTING PLATE

AREA. Locate and mark holes to align with holes in the

mounting plate.

IMPORTANT:

LOCATE AT LEAST ONE STUD ON EITHER SIDE OF

THE CENTERLINE.

MARK THE LOCATION FOR 2 ADDITIONAL, EVENLY

SPACED TOGGLE BOLTS IN THE MOUNTING PLATE

AREA. Trim the rear wall template along the dotted line.

Trim the rear wall template along the dotted line.

12"

4"

Darle vuelta a la hoja para consultar la

versin en Espaol.

Plaque de montage

FR-12

IMPORTANT: Ne pas retirer les entretoises en carton entre l' cran thermique et la porte.

Instructions dinstallation

UTILISATION DU GABARIT POUR ARMOIRE SUPRIEURE POUR LA PRPARATION DE LARMOIRE SUPRIEURE

A2.

Vous devez percer des trous pour les vis de soutien suprieures, ainsi quun trou suffisamment grand pour y faire passer le cordon dalimentation et une ouverture assez grande pour ladaptateur dvacuation.

Lisez les instructions sur le GABARIT POUR ARMOIRE SUPRIEURE.

Collez-le sous larmoire suprieure laide de ruban adhsif.

Percez les trous, en suivant les directives du GABARIT POUR ARMOIRE SUPRIEURE.

ATTENTION: Portez des lunettes de scurit lorsque vous percez des trous dans le fond de larmoire.

A3.

2

1

3

4

ADAPTATION DU VENTILATEUR DU FOUR MICRO-ONDES POUR L VACUATION LEXTRIEUR PAR LE DESSUS

Enlevez et conservez la vis qui retient le moteur du ventilateur au four micro-ondes.

Arrire du four micro-ondes

Plaque du ventilateur

Vis du moteur du ventilateur

Enlevez la vis qui retient la plaque du ventilateur sur le four micro-ondes. Enlevez et conservez la vis qui retient le moteur du ventilateur sur le four micro-ondes.

Enlevez dlicatement lensemble du ventilateur. Les fils seront assez longs pour vous permettre dadapter le ventilateur.

Arrire du four micro-ondes

Extrmit A

Extrmit B

Tournez le moteur de 90 afin que les ouvertures des

Arrire du four micro-ondes

Arrire du four micro-ondes

Avant la modification Aprs la modification

pales du ventilateur orientes vers le haut.

Replacez lensemble du ventilateur dans louverture.

des pales du ventilateur orientes vers le haut

APRS : Ouvertures

Arrire du four micro-ondes

ATTENTION : Ne tirez pas sur les fils de lensemble du ventilateur et ne les tirez pas. Assurez-vous que les fils ne sont pas coincs et quil sont fixs solidement.

FR-13

Instructions dinstallation

INSTALLATION DU FOUR MICRO-ONDES

REMARQUE: Lors de linstallation du four micro- ondes, faites passer le cordon dalimentation travers le trou situ dans le fond de larmoire suprieure. Gardez-le bien serr durant les tapes 1 3. Ne coincez pas le cordon et ne vous en servez pas pour soulever le four.

Soulevez le four, penchez-le vers lavant, et accrochez les fentes situes sur le bord infrieur larrire du four sur les quatre languettes infrieures de la plaque de montage.

1

Relevez le devant du four pour le mettre contre le dessous de larmoire.

2

Insrez une vis auto-alignement dans le trou situ au centre de larmoire suprieure. Fixez temporairement le four en faisant faire au moins deux tours complets la vis aprs que les filets aient t engags. (Elle sera compltement resserre plus tard.) Assurez-vous que le cordon dalimentation est bien serr. Faites attention de ne pas le coincer, particulirement au moment dinstaller le four sous larmoire.

3

POUR VOTRE SCURIT ET POUR FACILITER LINSTALLATION, LINSTALLATION DE CE FOUR DOIT TRE EFFECTUE PAR DEUX PERSONNES

REMARQUE: Si vos armoires sont en mtal, installez un passe- fil en nylon autour de lorifice du cordon dalimentation pour empcher que le cordon soit coup. REMARQUE: Si le four est install sous une armoire dote dun rebord avant, nous vous recommandons dutiliser des entretoises.

IMPORTANT : Si vous nutilisez pas dentretoises, des dommages peuvent tre causs au botier au moment du resserrage des vis.

VRIFICATION DU FONCTIONNEMENT DU REGISTRE

Assurez-vous que le ruban adhsif qui retient le registre a t enlev et que le registre bouge librement avant dinstaller le four.

Vous devrez effectuer les ajustements ncessaires pour vous assurer que le conduit du four est bien align sur le conduit dvacuation du domicile aprs linstallation du four.

Plaque du ventilateur

Registre

Arrire du four micro-ondes

Adaptateur de conduit dvacuation

A4.

A3.

5

6

7

ADAPTATION DU VENTILATEUR DU FOUR MICRO-ONDES POUR LVACUATION LEXTRIEUR PAR LE DESSUS

Fixez lensemble de ventilateur au four micro-ondes

est bien serre. Replacez la plaque du ventilateur en utilisant la vis de ltape 1. Assurez-vous que la vis est bien serre.

en utilisant la vis de ltape 1. Assurez-vous que la vis

micro-ondes

Arrire du four micro-ondes

Adaptateur

Guide

Fentes de blocage

Insrez-le jusqu ce quil soit dans les fentes de blocage infrieures. Assurez-vous que la charnire

A5.

Fixez ladaptateur dvacuation en haut du plaque du

Arrire du four

ventilateur en le coulissant dans les guides situs, la partie suprieure arrire du plaque du ventilateur.

du registre est installe et que le registre bouge librement.

FR-14

IMPORTANT: Ne pas saisir ou utiliser la poigne ou

l'cran thermique durant l'installation. Ne pas retirer les

entretoises en carton entre l'cran thermique et la porte.

Instructions dinstallation

INSTALLATION DU FOUR MICRO-ONDES (suite)

Avant de larmoire tagre infrieure de larmoire

Entretoise

Vis auto-alignement

Dessus du four micro-ondes

quivalent la hauteur du rebord de larmoire

Fixez le four micro-ondes larmoire suprieure.4

Serrez les deux vis de chaque ct dans le dessus du four micro-ondes. (Tout en serrant les vis, soulevez lavant du four micro-ondes et poussez-le contre le mur et larmoire suprieure.)

7

Insrez deux vis auto-alignement travers les trous de larmoire suprieure. Faites faire deux tours complets chaque vis.

5

Serrez compltement la vis du centre.

6

AJUSTEMENT DE LADAPTATEUR DVACUATION

Plaque du ventilateur Registre Arrire du four micro-ondes

Pour un ajustement de lavant larrire ou de ct ct, glissez ladaptateur dvacuation tel que requis

Ouvrez larmoire suprieure et ajustez ladaptateur dvacuation pour le relier au conduit dvacuation du domicile.

CONNEXION AU CONDUIT Conduit du domicile

Tirez sur le conduit du domicile pour le raccorder ladaptateur dvacuation.

2

1

A5. A6.

A7.

Scellez les joints du conduit dvacuation laide de ruban adhsif en toile convenant des tempratures leves.Installez les filtres. Consultez le Manuel de lutilisateur

emball avec le four. 8

FR-15

IMPORTANT: Retirer les entretoises en carton entre l' cran thermique et la porte.

Instructions dinstallation

VACUATION LEXTRIEUR PAR LARRIRE (Conduit horizontal)

B

VUE DENSEMBLE DE LINSTALLATION B1. Prparation du mur arrire

B3. Fixation de la plaque de montage au mur B4. Prparation de larmoire suprieure B5. Ajustement du ventilateur B6. Installation du four micro-ondes REMARQUES IMPORTANTES : Assurez-vous que les vis du moteur du

ventilateur et de la plaque du ventilateur sont solidement visses lorsque vous les remettez en place. Cela vitera les vibrations excessives.

Assurez-vous que les fils du moteur sont bien achemins, fixs et quils ne sont pas coincs.

Lisez les instructions figurant sur le GABARIT POUR MUR ARRIRE.

Collez-le au mur arrire.

Percez louverture en suivant les instructions sur le GABARIT POUR MUR ARRIRE.

PRPARATION DU MUR ARRIRE POUR LVACUATION LEXTRIEUR PAR LARRIRE

Vous devez percer une ouverture dans le mur arrire lvacuation lextrieur.

B1. B2. ENLVEMENT DE LPLAQUE DU VENTILATEUR

Enlevez et conservez la vis qui retient la plaque du ventilateur au four micro-ondes. Soulevez la plaque du ventilateur.

Plaque du ventilateur

Arrire du four micro-ondes

B2. Enlvement de lplaque du ventilateur 3/8" TO EDGE

NOTE: IT IS VERY IMPORTANT TO

READ AND FOLLOW THE DIRECTIONS

IN THE INSTALLATION INSTRUCTIONS

BEFORE PROCEEDING WITH THIS

REAR WALL TEMPLATE.

This Rear Wall Template serves to position the bottom

mounting plate and to locate the horizontal exhaust

outlet. 1. Use a level to check that the template is positioned

accurately. 2. Locate and mark at least one stud on the left or

right side of the centerline.

It is important to use at least one wood

screw mounted firmly in a stud to support the weight

of the microwave. Mark two additional, evenly spaced

locations for the supplied toggle bolts.

3. Drill holes in the marked locations. Where there is

a stud, drill a 3/16" hole for wood screws. For holes

that do not line up with a stud, drill 5/8" holes for

toggle bolts. DO NOT INSTALL THE MOUNTING PLATE

AT THIS TIME.

4. Remove the template from the rear wall.

5. Review the Installation Instruction book for your

installation situation.

Locate and mark holes to align with holes in the

mounting plate.

IMPORTANT:

LOCATE AT LEAST ONE STUD ON EITHER SIDE OF

THE CENTERLINE.

MARK THE LOCATION FOR 2 ADDITIONAL, EVENLY

SPACED TOGGLE BOLTS IN THE MOUNTING PLATE

AREA. Locate and mark holes to align with holes in the

mounting plate.

IMPORTANT:

LOCATE AT LEAST ONE STUD ON EITHER SIDE OF

THE CENTERLINE.

MARK THE LOCATION FOR 2 ADDITIONAL, EVENLY

SPACED TOGGLE BOLTS IN THE MOUNTING PLATE

AREA. Trim the rear wall template along the dotted line.

Trim the rear wall template along the dotted line.

12"

4"

Darle vuelta a la hoja para consultar la

versin en Espaol.

FR-16

IMPORTANT: Ne pas retirer les entretoises en carton entre l' cran thermique et la porte.

Instructions dinstallation

FIXATION DE LA PLAQUE DE MONTAGE AU MUR

B3.

ADAPTATION DU VENTILATEUR DU FOUR MICRO-ONDES POUR LVACUATION LEXTRIEUR PAR LARRIRE

B5.

Pour utiliser les boulons ailettes :

Enlevez et conservez la vis qui retient le moteur du ventilateur au four micro-ondes.

1

Enlevez dlicatement lensemble du ventilateur. Les fils seront assez longs pour vous permettre dajuster la position du ventilateur.

2

Moteur du ventilateur

Espace pour les ailettes suprieur lpaisseur du mur

crou ailettes Boulon ailettes

Plaque de montage

Mur Extrmit du boulon

Arrire du four micro-ondes

Vis du moteur du ventilateur

Extrmit B

Extrmit A

Placez la plaque de montage contre le mur et insrez les crous ailettes dans les trous du mur pour fixer la plaque.

REMARQUE: Avant de resserrer les boulons ailettes et la vis bois, assurez-vous que la plaque est bien centre sous larmoire et que les languettes de la plaque de montage touchent le dessous de larmoire lorsque vous poussez la plaque contre le mur. ATTENTION: Faites attention de ne pas vous pincer les doigts entre larrire de la plaque de montage et le mur.

Serrez tous les boulons. Tirez sur la plaque pour faciliter le serrage des boulons.

4

3

Fixez la plaque au mur laide des boulons ailettes. Vous devez utiliser au moins une vis bois pour fixer la plaque un montant.

Enlevez les crous ailettes des boulons.

Insrez les boulons dans la plaque de montage travers les trous dans le gypse et rassemblez les crous ailettes, 3 / 4 po (19 mm) sur chaque boulon.

2

1

UTILISATION DU GABARIT POUR ARMOIRE SUPRIEURE POUR LA PRPARATION DE LARMOIRE SUPRIEURE

Vous devez percer des trous pour les vis de soutien suprieures, ainsi quun trou suffisamment grand pour y faire passer le cordon dalimentation.

B4.

Lisez les instructions sur le GABARIT POUR ARMOIRE SUPRIEURE.

Collez-le sous larmoire suprieure laide de ruban adhsif.

Percez les trous, en suivant les directives du GABARIT POUR ARMOIRE SUPRIEURE.

ATTENTION: Portez des lunettes de scurit lorsque vous percez des trous dans le fond de larmoire.

pales du ventilateur orientes vers lavant

AVANT : Ouvertures des

FR-17

Instructions dinstallation

ADAPTATION DU VENTILATEUR DU FOUR MICRO-ONDES POUR LVACUATION LEXTRIEUR PAR LARRIRE (suite)

B5.

Retournez lensemble du ventilateur dans le sens contraire des aiguilles dune montre, sur 180.

Enlevez dlicatement les fils des encoches. Replacez les fils dans les encoches de lautre ct de lensemble du ventilateur.

Replacez lensemble du ventilateur dans louverture.

Tournez le moteur de 90 afin que les ouvertures des pales du ventilateur soient orientes vers larrire du four micro-ondes.

Replacez la plaque du ventilateur au mme endroit quavant avec la vis. Assurez-vous que la vis est bien serre.

Fixez ladaptateur dvacuation larrire du four en le coulissant dans les guides situs au centre, la partie suprieure arrire du four.

Insrez-le jusqu ce quil soit dans les fentes de

blocage infrieures. Assurez-vous que la charnire

du registre est installe sur le dessus et que le

registre bouge librement.

Avant la rotation

Avant la modification

Avant le roulement Aprs le roulement

Les fils sont achemins travers le ct droit

Les fils sont achemins travers le ct gauche

Aprs la modification

Aprs la rotation

Extrmit A

Extrmit B

Plaque du ventilateur

Adaptateur

Guide

Guide

Fentes de blocage

Arrire du four micro-ondes

Arrire du four micro-ondes

Vis du moteur du ventilateur

Arrire du four micro-ondes

Arrire du four micro-ondes

Arrire du four micro-ondes

Arrire du four micro-ondes

APRS : Ouvertures des pales du ventilateur orientes vers larrire

ATTENTION : Ne tirez pas sur les fils de lensemble du ventilateur et ne les tirez pas. Assurez-vous que les fils ne sont pas coincs et quil sont fixs solidement. REMARQUE : Les ouvertures de lensemble du ventilateur doivent correspondre aux ouvertures de ventilation larrire du four micro-ondes.

Fixez lensemble de ventilateur au four micro-ondes en utilisant la vis dorigine.

3

Arrire du four micro-ondes

Arrire du four micro-ondes

Avant la rotation Aprs la rotation

Tournez le moteur de 90.

4

5

6

7

8

9

10

FR-18

Instructions dinstallation

INSTALLATION DU FOUR MICRO-ONDES

B6.

REMARQU: Lors de linstallation du four micro- ondes, faites passer le cordon dalimentation travers le trou situ dans le fond de larmoire suprieure. Gardez-le bien serr durant les tapes 1 3. Ne coincez pas le cordon ou ne soulevez pas le four en tirant sur le cordon.

Soulevez le four, penchez-le vers lavant et accrochez les fentes situes sur le bord infrieur larrire du four sur les quatre languettes infrieures de la plaque de montage.

1

Relevez le devant du four pour le mettre contre le dessous de larmoire.

2

Insrez une vis auto-alignement dans le trou situ au centre de larmoire suprieure. Fixez temporairement le four en faisant faire au moins deux tours complets la vis aprs que les filets aient t engags. (Elle sera compltement resserre plus tard.) Assurez-vous que le cordon dalimentation est bien serr. Faites attention de ne pas le coincer, particulirement au moment dinstaller le four sous larmoire.

3

Fixez le four micro-ondes larmoire suprieure.4

Serrez les deux vis de chaque ct dans le dessus du four micro-ondes. (Tout en serrant les vis, soulevez lavant du four micro-ondes et poussez-le contre le mur et larmoire suprieure.)

7

Insrez deux vis auto-alignement travers les trous de larmoire suprieure. Faites faire deux tours complets chaque vis.

5

Serrez compltement la vis du centre.

6

Avant de larmoire tagre infrieure de larmoire

Entretoise

Vis auto-alignement

Dessus du four micro-ondes

quivalent la profondeur du rebord de larmoire

POUR VOTRE SCURIT ET POUR FACILITER LINSTALLATION, LINSTALLATION DE CE FOUR DOIT TRE EFFECTUE PAR DEUX PERSONNES.

REMARQUE: Si vos armoires sont en mtal, installez un passe-fil en nylon autour de lorifice du cordon dalimentation pour empcher que le cordon soit coup. REMARQUE: Si le four est install sous une armoire dote dun rebord avant, nous vous recommandons dutiliser des entretoises. IMPORTANT: Si vous nutilisez pas dentretoises, des dommages peuvent tre causs au botier au moment de resserrer les vis.

Installez les filtres. Consultez le Manuel de lutilisateur emball avec le four.

8

FR-19

IMPORTANT: Retirer les entretoises en carton entre l' cran thermique et la porte.

IMPORTANT: Ne pas saisir ou utiliser la poigne ou

l'cran thermique durant l'installation. Ne pas retirer les

entretoises en carton entre l'cran thermique et la porte.

Instructions dinstallation

RECYCLAGE DAIR (vacuation sans conduit)C

FIXATION DE LA PLAQUE DE MONTAGE AU MUR

C1.

Placez la plaque de montage contre le mur et insrez les crous ailettes dans les trous du mur pour fixer la plaque.

REMARQUE: Avant de resserrer les boulons ailettes et la vis bois, assurez-vous que la plaque est bien centre sous larmoire et que les languettes de la plaque de montage touchent le dessous de larmoire lorsque vous poussez la plaque contre le mur. ATTENTION: Faites attention de ne pas vous pincer les doigts entre larrire de la plaque de montage et le mur.

Serrez tous les boulons. Tirez sur la plaque pour faciliter le serrage des boulons.

4

3

VUE DENSEMBLE DE LINSTALLATION C1. Fixation de la plaque de montage au mur C2. Prparation de larmoire suprieure

C4. C5.

Installation du four micro-ondes

REMARQUES IMPORTANTES : Assurez-vous que les vis du moteur du ventilateur et de la

plaque du ventilateur sont solidement visses lorsque vous les remettez en place. Cela vitera les vibrations excessives.

Assurez-vous que les fils du moteur sont bien achemins, fixs et quils ne sont pas coincs.

Fixez la plaque au mur laide des boulons ailettes. Vous devez utiliser au moins une vis bois pour fixer la plaque un montant.

C3. Vrification de lplaque du ventilateur 3/8" TO EDGE

NOTE: IT IS VERY IMPORTANT TO

READ AND FOLLOW THE DIRECTIONS

IN THE INSTALLATION INSTRUCTIONS

BEFORE PROCEEDING WITH THIS

REAR WALL TEMPLATE.

This Rear Wall Template serves to position the bottom

mounting plate and to locate the horizontal exhaust

outlet. 1. Use a level to check that the template is positioned

accurately. 2. Locate and mark at least one stud on the left or

right side of the centerline.

It is important to use at least one wood

screw mounted firmly in a stud to support the weight

of the microwave. Mark two additional, evenly spaced

locations for the supplied toggle bolts.

3. Drill holes in the marked locations. Where there is

a stud, drill a 3/16" hole for wood screws. For holes

that do not line up with a stud, drill 5/8" holes for

toggle bolts. DO NOT INSTALL THE MOUNTING PLATE

AT THIS TIME.

4. Remove the template from the rear wall.

5. Review the Installation Instruction book for your

installation situation.

Locate and mark holes to align with holes in the

mounting plate.

IMPORTANT:

LOCATE AT LEAST ONE STUD ON EITHER SIDE OF

THE CENTERLINE.

MARK THE LOCATION FOR 2 ADDITIONAL, EVENLY

SPACED TOGGLE BOLTS IN THE MOUNTING PLATE

AREA. Locate and mark holes to align with holes in the

mounting plate.

IMPORTANT:

LOCATE AT LEAST ONE STUD ON EITHER SIDE OF

THE CENTERLINE.

MARK THE LOCATION FOR 2 ADDITIONAL, EVENLY

SPACED TOGGLE BOLTS IN THE MOUNTING PLATE

AREA. Trim the rear wall template along the dotted line.

Trim the rear wall template along the dotted line.

12"

4"

Darle vuelta a la hoja para consultar la

versin en Espaol.Installation ou changemeut du filtre charbon

Espace pour les ailettes suprieur lpaisseur du mur

crou ailettes Boulon ailettes

Plaque de montage

Mur Extrmit du boulon

Pour utiliser les boulons ailettes :

Enlevez les crous ailettes des boulons.

Insrez les boulons dans la plaque de montage travers les trous dans le gypse et rassemblez les crous ailettes, 3 / 4 po (19 mm) sur chaque boulon.

2

1

Armoire

REMARQUE: Si la profondeur du armoire incluant les portes du armoire est plus de 13'' alors l'unit doit tre espace du mur utilisant des matriaux adquats supportant 150 lbs pour permettre une bonne ventilation d'air au sommet/admission d'air.

Armoire

FR-20

IMPORTANT: Ne pas retirer les entretoises en carton entre l' cran thermique et la porte.

Instructions dinstallation

REMARQUE: Lors de linstallation du four micro- ondes, faites passer le cordon dalimentation travers le trou situ dans le fond de larmoire suprieure. Gardez-le bien serr durant les tapes 1 3. Ne coincez pas le cordon ou ne soulevez pas le four en tirant sur le cordon.

Soulevez le four micro- ondes, penchez-le vers lavant et accrochez les fentes du bord infrieur de larrire du four sur les quatre languettes infrieures de la plaque de montage.

1

Relevez le devant du four pour le mettre contre le dessous de larmoire.

2

Insrez une vis auto-alignement dans le trou situ au centre de larmoire suprieure. Fixez temporairement le four en faisant faire au moins deux tours complets la vis aprs que les filets aient t engags. (Elle sera compltement resserre plus tard.) Assurez-vous que le cordon dalimentation est bien serr. Faites attention de ne pas le coincer, particulirement au moment dinstaller le four sous larmoire.

3

Fixez le four micro-ondes larmoire suprieure.

C3. VRIFICATION DE LPLAQUE DU VENTILATEUR

Plaque du ventilateur

Placez le four micro-ondes en position debout, le dessus de lappareil sur le dessus.

Inspectiez pour affirmer le ventilateur metal est installez dans la cavit.

UTILISATION DU GABARIT POUR ARMOIRE SUPRIEURE POUR LA PRPARATION DE LARMOIRE SUPRIEURE

Vous devez percer des trous pour les vis de soutien suprieures, ainsi quun trou suffisamment grand pour y faire passer le cordon dalimentation.

C2.

Lisez les instructions sur le GABARIT POUR ARMOIRE SUPRIEURE.

Collez-le sous larmoire suprieure laide de ruban adhsif.

Percez les trous, en suivant les instructions du GABARIT POUR ARMOIRE SUPRIEURE.

ATTENTION : Portez des lunettes de scurit lorsque vous percez des trous dans le fond de larmoire.

REMARQUE: Ajustez correctement le haut du gabarit si le micro-ondes devient espac du mur cause de la profondeur du armoire (incluant les portes du armoire) de plus de 13".

Avant de larmoire tagre infrieure de larmoire

Entretoise

Vis auto-alignement

Dessus du four micro-ondes

quivalent la profondeur du rebord de larmoire

INSTALLATION DU FOUR MICRO-ONDES

C4.

4

POUR VOTRE SCURIT ET POUR FACILITER LINSTALLATION, LINSTALLATION DE CE FOUR DOIT TRE EFFECTUE PAR DEUX PERSONNES.

REMARQUE: Si vos armoires sont en mtal, installez un passe-fil en nylon autour de lorifice du cordon dalimentation pour empcher que le cordon soit coup. REMARQUE: Si le four est install sous une armoire dote dun rebord avant, nous vous recommandons dutiliser des entretoises. IMPORTANT: Si vous nutilisez pas dentretoises, des dommages peuvent tre causs au botier au moment de resserrer les vis.

FR-21

IMPORTANT: Ne pas saisir ou utiliser la poigne ou

l'cran thermique durant l'installation. Ne pas retirer les

entretoises en carton entre l'cran thermique et la porte.

Instructions dinstallation

Insrez deux vis auto-alignement travers les trous de larmoire suprieure. Faites faire deux tours complets chaque vis.

5

Serrez compltement la vis du centre.

6

INSTALLATION DU FOUR MICRO-ONDES (suite)

Serrez les deux vis de chaque ct dans le dessus du four micro-ondes. (Tout en serrant les vis, soulevez lavant du four micro-ondes et poussez-le contre le mur et larmoire suprieure.)

7

C4.

1

C5.

CHARBON (Certains modles)

INSTALLATION OU CHANGEMEUT DU FILTRE

REMARQUE: Le filtre charbon de bois est install d'usine dans certains modles. Refrez-vous l'utilisation et soin pour voir si le vtre est install d'usine et pour l'information de remplacement. Suivez ces tapes pour remplacer ou installer un filtre charbon de bois.

3

2

4

Tableaux

5

6

Dbranchez le four micro-ondes ou dconnectez l'alimentation.

Ouvrez la porte du mirco-ondes et enlevez les deux vis de montage du tuyau localiss en haut du micro-ondes utilisant un #1 pilote de vis Phillips.

et enlevez.

Installez le filtre charbon de bois. Mettez le filtre l'arrire du grille avec la maille noir faisant face au suprieur.

Filtre charbon de bois

Rinstallez le tuyau en faisant glisser l'arrire du tuyau en place. Poussez le haut du tuyau en position et faites le bien glisser en pace. Replacez les deux vis de montage du tuyau localiss en haut du mirco-ondes utilisant un #1 pilote de vis Phillips.

Fermez la porte du micro-ondes. Branchez le four micro- ondes ou reconnectez l'alimentation.

Basculez en avant. Soulevez

Installez les filtres. Consultez le Manuel de lutilisateur emball avec le four.

8

FR-22

IMPORTANT: Retirer les entretoises en carton entre l' cran thermique et la porte.

Instructions dinstallation

AVANT DUTILISER VOTRE FOUR MICRO-ONDES

Assurez-vous que le four micro-ondes a t install conformment aux instructions.

1.

6.

7.

Enlevez tout le matriel demballage du four micro-ondes.

2.

Installez le plateau tournant et la plateau en verre dans le four micro-ondes.

3.

Assurez-vous quune mise la terre approprie est en place avant toute utilisation.

INSTRUCTIONS

DINSTALLATION

INSTRUCTIONS

DINSTALLATION

MANUEL DE

LUTILISATEUR

Branchez le cordon dalimentation

Lisez le manuel dutilisation et dentretien.

Rinstallez le fusible ou renclenchez le disjoncteur du panneau de distribution principal.

4.

5.

CONSERVEZ LES INSTRUCTIONS DINSTALLATION POUR VOTRE INSPECTEUR LOCAL.

8.

CARTE

DENREGISTREMENT

DU PRODUIT

Remplissez la carte denregistrement du produit.

FR-23

s par e

et

d di e sur une prise de courant rserve de 15 20 A.

Imprim en Chine

Part No.:77222316902477

3/8" TO EDGE

NOTE: IT IS VERY IMPORTANT TO READ AND FOLLOW THE DIRECTIONS

IN THE INSTALLATION INSTRUCTIONS

BEFORE PROCEEDING WITH THIS REAR WALL TEMPLATE.This Rear Wall Template serves to position the bottom

mounting plate and to locate the horizontal exhaust

outlet. 1. Use a level to check that the template is positioned

accurately. 2. Locate and mark at least one stud on the left or

right side of the centerline. It is important to use at least one wood

screw mounted firmly in a stud to support the weight

of the microwave. Mark two additional, evenly spaced

locations for the supplied toggle bolts.

3. Drill holes in the marked locations. Where there is

a stud, drill a 3/16" hole for wood screws. For holes

that do not line up with a stud, drill 5/8" holes for

toggle bolts. DO NOT INSTALL THE MOUNTING PLATE AT THIS TIME. 4. Remove the template from the rear wall.

5. Review the Installation Instruction book for your

installation situation.

Locate and mark holes to align with holes in the

mounting plate. IMPORTANT: LOCATE AT LEAST ONE STUD ON EITHER SIDE OF

THE CENTERLINE. MARK THE LOCATION FOR 2 ADDITIONAL, EVENLY

SPACED TOGGLE BOLTS IN THE MOUNTING PLATE

AREA.

Locate and mark holes to align with holes in the

mounting plate. IMPORTANT: LOCATE AT LEAST ONE STUD ON EITHER SIDE OF

THE CENTERLINE. MARK THE LOCATION FOR 2 ADDITIONAL, EVENLY

SPACED TOGGLE BOLTS IN THE MOUNTING PLATE

AREA.

Trim the rear wall template along the dotted line.

Trim the rear wall template along the dotted line.

12"

4"

Darle vuelta a la hoja para consultar la

versin en Espaol.

3/8" TO EDGE

NOTE: IT IS VERY IMPORTANT TO

READ AND FOLLOW THE DIRECTIONS

IN THE INSTALLATION INSTRUCTIONS

BEFORE PROCEEDING WITH THIS

REAR WALL TEMPLATE.This Rear Wall Template serves to position the bottom

mounting plate and to locate the horizontal exhaust

outlet. 1. Use a level to check that the template is positioned

accurately. 2. Locate and mark at least one stud on the left or

right side of the centerline.

It is important to use at least one wood

screw mounted firmly in a stud to support the weight

of the microwave. Mark two additional, evenly spaced

locations for the supplied toggle bolts.

3. Drill holes in the marked locations. Where there is

a stud, drill a 3/16" hole for wood screws. For holes

that do not line up with a stud, drill 5/8" holes for

toggle bolts. DO NOT INSTALL THE MOUNTING PLATE

AT THIS TIME. 4. Remove the template from the rear wall.

5. Review the Installation Instruction book for your

installation situation.

Locate and mark holes to align with holes in the

mounting plate. IMPORTANT: LOCATE AT LEAST ONE STUD ON EITHER SIDE OF

THE CENTERLINE. MARK THE LOCATION FOR 2 ADDITIONAL, EVENLY

SPACED TOGGLE BOLTS IN THE MOUNTING PLATE

AREA.

Locate and mark holes to align with holes in the

mounting plate. IMPORTANT: LOCATE AT LEAST ONE STUD ON EITHER SIDE OF

THE CENTERLINE. MARK THE LOCATION FOR 2 ADDITIONAL, EVENLY

SPACED TOGGLE BOLTS IN THE MOUNTING PLATE

AREA.

Trim the rear wall template along the dotted line.

Trim the rear wall template along the dotted line.

12"

4"

Darle vuelta a la hoja para consultar la

versin en Espaol.

Part No.: 316

P N

:2 61

80 03

11 39

5

495140

REMARQUE: IL EST TRS IMPORTANT DE LIRE ET DE RESPECTER LES INSTRUCTIONS D'INSTALLATION AVANT D'UTILISER CE GABARIT POUR MUR ARRIRE. Ce gabarit sert d terminer l'emplacement de l'ouverture du conduit d' vacuation horizontal. 1. Utilisez un niveau pour vrifier que le gabarit est positionn prcis ment. 2. Reprer et marquer au moins un montant sur la gauche ou la droite de la ligne mdiane. REMARQUE: Il est important d'utiliser au moins une vis bois fermement monte dans un montant pour supporter le poids du micro-onde. Marquez deux autres,

ailettes fournis. 3. Percez des trous aux emplacements marqus. L o il y a un montant, percez un trou de 3/16 po pour les vis bois.

REMARQUE: NE FIXEZ PAS LA PLAQUE DE MONTAGE

4. Enlevez le gabarit du mur arrire. 5. Reportez-vous aux inst d'inst pour les tapes suivantes.

Coupez le gabarit pour le mur arrire le long de la ligne pointille.

Coupez le gabarit pour le mur arrire le long de la ligne pointille.

Localiser et marquer les trous aligner avec les trous dans la plaque de montage. IMPORTANT:

LA LIGNE MDIANE. MARQUEZ L'EMPLACEMENT POUR DEUX AUTRES BOULONS AILETTES,

ESPACES, DANS LA ZONE DE LA PLAQUE DE MONTAGE.

Localiser et marquer les trous aligner avec les trous dans le la plaque de montage. IMPORTANT: PLACEZ AU MOINS UN MONTANT SUR L'AUTRE CT DE LA LIGNE MDIANE. MARQUEZ DEUX AUTRES BOULONS AILETTES, UNIFORMMENT ESPACES, DANS LA PLAQUE DE MONTAGE ZONE.

Turun over for English

emplacements,uniformment espaces, pour les boulons

Pour les trous qui ne s'alignent pas avec un montant, percez un trou de 5/8 po pour les boulons ailettes.

IMMEDIATEM

Manualsnet FAQs

If you want to find out how the FPBM3077RF Frigidaire works, you can view and download the Frigidaire FPBM3077RF Installation Instructions on the Manualsnet website.

Yes, we have the Installation Instructions for Frigidaire FPBM3077RF as well as other Frigidaire manuals. All you need to do is to use our search bar and find the user manual that you are looking for.

The Installation Instructions should include all the details that are needed to use a Frigidaire FPBM3077RF. Full manuals and user guide PDFs can be downloaded from Manualsnet.com.

The best way to navigate the Frigidaire FPBM3077RF Installation Instructions is by checking the Table of Contents at the top of the page where available. This allows you to navigate a manual by jumping to the section you are looking for.

This Frigidaire FPBM3077RF Installation Instructions consists of sections like Table of Contents, to name a few. For easier navigation, use the Table of Contents in the upper left corner.

You can download Frigidaire FPBM3077RF Installation Instructions free of charge simply by clicking the “download” button in the upper right corner of any manuals page. This feature allows you to download any manual in a couple of seconds and is generally in PDF format. You can also save a manual for later by adding it to your saved documents in the user profile.

To be able to print Frigidaire FPBM3077RF Installation Instructions, simply download the document to your computer. Once downloaded, open the PDF file and print the Frigidaire FPBM3077RF Installation Instructions as you would any other document. This can usually be achieved by clicking on “File” and then “Print” from the menu bar.