Frigidaire FFRS1022RE Owner's Guide PDF

1 of 12
1 of 12

Summary of Content for Frigidaire FFRS1022RE Owner's Guide PDF

TABLE OF CONTENTS

www.frigidaire.com USA 1-800-944-9044 www.frigidaire.ca Canada 1-800-265-8352

All about the

Use & Care

16120300A04523 (June 2009)

Product Registration 4

.............................................

Normal Sounds .................................................... 4 Air Conditioner Features 5.......................................

Important Safety Instructions ............................... 2-3

Operating Instructions 5-10..........................................

Care and Cleaning .............................................. 10

Energy Saving Ideas ........................................... 10

Before You Call ................................................... 11

Major Appliance Limited Warranty ........................ 12

of your Room Air Conditioner

Important Safety Instructions

Grounding type wall receptacle

Do not, under any circumstances, cut, remove, or bypass the grounding prong.

Power supply cord with 3-prong grounding plug and current detection device

WARNING

For Your Safety Do not store or use gasoline or other flammable vapors and liquids in the vicinity of this or any other appliance. Read product labels for flammability and other warnings.

WARNING

Prevent Accidents To reduce the risk of fire, electrical shock, or injury to persons when using your air conditioner, follow basic precautions, including the following:

Be sure the electrical service is adequate for the model you have chosen. This information can be found on the serial plate, which is located on the side of the cabinet and behind the grille. If the air conditioner is to be installed in a window, you will probably want to clean both sides of the glass first. If the window is a triple-track type with a screen panel included, remove the screen completely before installation. Be sure the air conditioner has been securely and correctly installed according to the separate installation instructions provided with this manual. Save this manual and the installation instructions for possible future use in removing or reinstalling this unit. When handling the air conditioner, be careful to avoid cuts from sharp metal fins on front and rear coils.

The complete electrical rating of your new room air conditioner is stated on the serial plate. Refer to the rating when checking the electrical requirements.

Be sure the air conditioner is properly grounded. To minimize shock and fire hazards, proper grounding is important. The power cord is equipped with a three-prong grounding plug for protection against shock hazards. Your air conditioner must be used in a properly grounded wall receptacle. If the wall receptacle you intend to use is not adequately grounded or protected by a time delay fuse or circuit breaker, have a qualified electrician install the proper receptacle. Do not run air conditioner without outside protective cover in place. This could result in mechanical damage within the air conditioner. Do not use an extension cord or an adapter plug.

WARNING

Electrical Information

WARNING

Avoid fire hazard or electric shock. Do not use an extension cord or an adaptor plug. Do not remove any prong from the power cord.

NOTE: The power supply cord with this air conditioner contains a current detection device designed to reduce the risk of fire. Please refer to the section Operation of Current Device for details. In the event that the power supply cord is damaged, it cannot be repaired. It must be replaced with a cord from the product manufacturer.

2 2009 Electrolux Home Products, Inc. All rights reserved.

NOTE:

This USE & CARE MANUAL provides specific operating instructions for your model. Use the room air conditioner only as instructed in this USE & CARE MANUAL. These instructions are not meant to cover every possible condition and situation that may occur. Common sense and caution must be practiced when installing, operating, and maintaining any appliance.

SAFETY PRECAUTIONS

This air conditioner contains no user-serviceable parts. Always call an authorized Electrolux servicer for repairs. Do not insert or place fingers or objects into the air discharge area in the front of the unit. Do not start or stop the air conditioner by unplugging the power cord or turning off the power at the electrical box. Do not cut or damage the power cord. If the power cord is damaged, it should only be replaced by an authorized Electrolux servicer. In the event of a malfunction (sparks, burning smell, etc.), immediately stop the operation, disconnect the power cord, and call an authorized Electrolux servicer. Do not operate the air conditioner with wet hands. Do not pull on the power cord. Do not drink any water that is drained from the air conditioner.

DANGER! Avoid Serious Injury or Death

Important Safety Instructions

3 2009 Electrolux Home Products, Inc. All rights reserved.

READ THIS SECTION BEFORE ATTEMPTING TO OPERATE AIR CONDITIONER. Unit must be upright for one hour prior to operating.

Plug in & press RESET

The power supply cord contains a current device that senses damage to the power cord. To test your power supply cord do the following:

Plug in the Air Conditioner. The power supply cord will have TWO buttons on the plug head. Press the TEST button. You will notice a click as the RESET button pops out.

Press the RESET button. Again you will notice a click as the button engages. The power supply cord is now supplying electricity to the unit. (This is also indicated by a light on the plug head).

NOTE:

Do not use this device to turn the unit on or off. Always make sure the RESET button is pushed in for correct operation. The power supply cord must be replaced if it fails to reset when either the TEST button is pushed, or it cannot be reset. A new one can be obtained from the product manufacturer. If power supply cord is damaged, it CANNOT be repaired. It MUST be replaced by one obtained from the product manufacturer.

SAFETY PRECAUTIONS

Provide occasional ventilation during use. Do not direct airflow at fireplaces or other heat related sources as this could cause flare ups or make units run excessively. Do not climb on or place objects on outdoor part of the unit. Do not hang objects off the unit. Do not place containers with liquids on the unit. Turn off the air conditioner at the power source when it will not be used for an extended period of time. Periodically check the condition of the units installation accessories for any damage. Do not apply heavy pressure to the radiator fins of the unit. Operate the unit with air filter in place. Do not block or cover the intake grille, discharge area and outlet ports. Ensure that any electrical/electronic equipment is one yard away from the unit. Do not use or store flammable gases near the unit. Do not touch the metal parts of the unit when removing the filter. Injuries can occur when handling sharp metal edges. Do not use water to clean inside the air conditioner. Exposure to water can destroy the insulation, leading to possible electric shock. When cleaning the unit, first make sure that the power and circuit breaker are turned off.

CAUTION! Avoid Injury or damage to the unit or other property

Record Your Model and Serial Numbers

Record in the space provided below the model and serial numbers. On all models, the serial plate is located on the outside of the cabinet.

Model No.

Serial No.

Register Your Product

The self-addressed PRODUCT REGISTRATION CARD should be filled in completely, signed and returned to the Frigidaire Company.

Product Registration

4

Product Registration & Normal Sounds

2009 Electrolux Home Products, Inc. All rights reserved.

Normal Sounds

Todays high efficiency compressors may have a high pitched chatter during the cooling cycle.

High pitched Chatter

Unit may vibrate and make noise because of poor wall or window construction or incorrect installation.

Vibration

Sound of Rushing Air At the front of the unit, you may hear the sound of rushing air being moved by the fan.

Gurgle/Hiss Gurgling or hissing noise may be heard due to refrigerant passing through evaporator during normal operation.

Pinging or Swishing Droplets of water hitting condenser during normal operation may cause pinging or swishing sounds. Note: Dont try to drill any holes on the base pan to eliminate the normal sounds, otherwise it will void the warranty.

5

Air Conditioner Features & Operating Instructions

Before you begin, thoroughly familiarize yourself with the control panel and remote as shown below and all its functions, then follow the symbol for the functions you desire. The unit can be controlled by the touch pad alone or with the remote.

ELECTRONIC CONTROLAir Conditioner Features

2009 Electrolux Home Products, Inc. All rights reserved.

NOTE

The following instructions represent the Touch Pad, the same instructions can be used for the Remote Control.

Operating Instructions

PRESS ON/OFF BUTTON

DO THIS:

TO TURN UNIT ON: YOU WILL SEE:

ADJUSTS TEMPERATURE OR TIME

DISPLAYS TEMPERATURE/TIME

SETS FAN SPEED

SETS MODE TURNS UNIT ON OR OFF

ACTIVATES TIMER

EXHAUST SELECTOR

CHECK FILTER RESET BUTTON

SLEEP MODE

STANDARD REMOTE

Battery Size: AAA Warning: Do not mix old and new batteries. Do not mix alkaline, standard (carbon-zinc), or rechargeable (nickel-cadmium) batteries.

Note: The unit will run in energy saver mode when used for the first time. In this mode, the fan will continue to run for 1 minute after the compressor shuts off. The fan then cycles on for 20 seconds at 10 minute intervals until the room temperature is above the set temperature, at which time the compressor turns back on.

6

Operating Instructions

TO CHANGE TEMPERATURE SETTlNG:

TO ADJUST FAN SPEEDS:

YOU WILL SEE:TO USE AUTO FAN FEATURE:

Note: Fan starts at High Speed and adjusts to a slower speeds the room temperature dictates. For example, if the room doesn't get too warm, it will stay at the slowest speed. If the room temperature rises quickly, such as a door being opened, it will auto- matically go to the highest speed. The fan speeds will re-adjust back to the slowest speed as the room returns to the original set temperature. Press either the fan slower or fan faster button to adjust the fan speed manually.

2009 Electrolux Home Products, Inc. All rights reserved.

YOU WILL SEE:

YOU WILL SEE:

DO THIS:

PRESS TO RAISE

PRESS TO LOWER

DO THIS:

PRESS TO SELECT

Operating Instructions (continued)

Note: Tap or hold either up ( ) or down ( ) button until the desired temperature is seen on the display. This tempe- rature will be automatically maintained anywhere between 60 F (16 C) and 90 F (32 C) . If you want the display to read the actual room temperature. See "To Operate on Fan Only" section on Page 7.

PRESS FAN BUTTON CHOOSE AUTO

DO THIS:

7

Operating Instructions

Operating Instructions (continued) TO OPERATE ON FAN ONLY: YOU WILL SEE:

COOL FEATURE: YOU WILL SEE:

2009 Electrolux Home Products, Inc. All rights reserved.

DO THIS:

PRESS MODE BUTTON

CHOOSE FAN ONLY

DO THIS:

PRESS MODE BUTTON

Note: In this mode the selected temperature will increase by 2 F 30 minutes after the mode is selected. The tempe- rature will then increase by another 2 F after an additional 30 minutes. This new temperature will be maintained for 7 hours before it returns to the originally selected tempera- ture. This ends the "Sleep" mode and the unit will continue to operate as originally programmed. The "Sleep" mode program can be cancelled at any time during operation by again pressing the "Sleep" button.

SLEEP FEATURE:

DO THIS:

PRESS SLEEP BUTTON

YOU WILL SEE:

Note: Use this function only when cooling is not desired, such as for room air circulation or to exhaust stale air on some models. (Remember to open the vent during this function, but keep it closed during cooling for maximum cooling efficiency.) You can choose any fan speed you prefer. (Except Auto Fan). During this function, the display will show the actual room temperature, not the set temperature as in the cooling mode.

Note: In this mode, the fan remains on all the time with the compressor cycling on and off when room temperature is reached.

CHOOSE COOL

8

Operating Instructions

Operating Instructions (continued)

CHECK FILTER FEATURE, YOU WILL SEE:

2009 Electrolux Home Products, Inc. All rights reserved.

DO THIS:

PRESS FILTER RESET BUTTON

TIMER: DELAY STOP / START FEATURE YOU WILL SEE HOW MUCH TIME IS CHOSEN:

Note: For Delay Stop, the unit must be in the On position. Note: For Delay Start, the unit must be in the Off position.

FIRST DO THIS:

PRESS TIMER BUTTON

THEN DO THIS:

Note: This feature is a reminder to clean the Air Filter (See Care and Cleaning) for more efficient operation. The LED (light) will illuminate after 250 hours of operation. To reset after cleaning the filter, press the "Filter Reset" button and the light will go off.

If the display reads "AS" , a sensor has failed. Contact your Authorized Frigidaire Service Center.

If the display reads "ES" , a sensor has failed. Contact your Authorized Frigidaire Service Center.

FAULT CODES:

First, Press TIMER button, then adjust timer setting, tap or hold the UP arrow ( ) or the DOWN arrow ( ) to change delay timer at 0.5 hour increments, up to 10 hours, then at 1 hour increments up to 24 hours. The control will count down the time remaining until start (8, 7.5, 7, etc.). The Delay Start Operation automatically selects cooling with maximum Fan speed (if Cool, Energy Saver, or Fan Only was the last mode selected) . The temperature maintained will be the same as previously set. To change the set tempera- ture, press "COOL" then Up or Down arrows until the de- sired temperature is indicated on the display. After 5 se- conds, the control will automatically change the display back to the hours remaining until the unit will start/stop. Pressing the unit On/Off button at any time will cancel the Delay Start/Stop function. The Delay Start/Stop Feature will work until the unit either starts or stops. Once that happens the above steps have to be repeated again.

PRESS UP/DOWN

SET BUTTONS

9

Operating Instructions

Operating Instructions (continued)

TO TURN UNIT OFF:

2009 Electrolux Home Products, Inc. All rights reserved.

YOU WILL SEE:

ADDITIONAL THINGS YOU SHOULD KNOW

DO THIS:

PRESS ON/OFF BUTTON

EXHAUST CONTROL

This Exhaust Control allows the air conditioner to either recirculate inside air (CLOSED) or exhaust air to the outside (OPEN). The CLOSED position is used when maximum cooling is desired. It may also be used for air recirculation without cooling when the air conditioner is set in any FAN position. The OPEN position removes stale air from the room and exhausts it to the outside. Fresh air is drawn in through normal passages in the home.

Now that you have mastered the operating procedure, here are more features in your control that you should become familiar with.

The "Cool" circuit has an automatic 3 minute time delayed start if the unit is turned off and on quickly. This prevents overheating of the compressor and possible circuit breaker tripping. The fan will continue to run during this time.

The control will maintain the set temperature within 2 degrees Fahrenheit, between 60F and 90F degrees.

There is a 2-Second delay for the compressor shutting down when selecting FAN ONLY. This is to cover the possibility of having to roll through to select another mode.

After a power outage, the unit will memorize the last setting and return the unit to the same setting once power is restored.

TO CHANGE TEMPERATURE DISPLAY: YOU WILL SEE:

DO THIS: PRESS AND HOLD THE UP/DOWN BUTTONS

TOGETHER FOR 3 SECONDS

Note: The control is capable of displaying temperature in degrees Fahrenheit or degrees Celsius.

Note: If the unit is turned off in heat mode (if applicable) or fan only mode, it will return to the same setting when it is turned on again. When the unit is turned off in cool or energy saver mode, it will run in energy saver mode when it is turned on again, but the setting of temperature and fan speed will remain.

Operating Instructions, Care and Cleaning & Energy Saving Ideas

10 2009 Electrolux Home Products, Inc. All rights reserved.

Energy Saving Ideas Do not block air flow inside with blinds, curtains or furniture; or outside with shrubs, enclosures, or other buildings. The capacity of the room air conditioner must fit the room size for efficient and satisfactory operation. Install the room air conditioner on the shady side of your home. A window that faces north is best because it is shaded most of the day. Close the fireplace damper, floor and wall registers so cool air does not escape up the chimney and into the duct work. Keep blinds and drapes in other windows closed during the sunniest part of the day. Clean the air filter as recommended in the section Care and Cleaning. Proper insulation and weather stripping in your home will help keep warm air out and cool air in. External house shading with trees, plants or awnings will help reduce the air conditioners work load. Operate heat producing appliances such as ranges, washers, dryers and dishwashers during the coolest part of the day.

Care and Cleaning Clean your air conditioner occasionally to keep it looking new. Be sure to unplug the unit before cleaning to prevent shock or fire hazards.

Cabinet Cleaning Be sure to unplug the air conditioner to prevent shock or fire hazard. The cabinet and front may be dusted with an oil-free cloth or washed with a cloth dampened in a solution of warm water and mild liquid dishwashing detergent. Rinse thoroughly and wipe dry. Never use harsh cleaners, wax or polish on the cabinet front. Be sure to wring excess water from the cloth before wiping around the controls. Excess water in or around the controls may cause damage to the air conditioner. Plug in air conditioner.

Winter Storage If you plan to store the air conditioner during the winter, remove it carefully from the window according to the installation instructions. Cover it with plastic or return it to the original carton. NOTE:To prevent rust or electrical connections from being damaged, store air conditioner in an upright position and a dry place.

Air Filter Cleaning The air filter should be checked at least once a month to see if cleaning is necessary. Trapped particles in the filter can build up and cause an accumulation of frost on the cooling coils.

Grasp the filter by the center and pull up and out. Wash the filter using liquid dishwashing detergent and warm water. Rinse filter thoroughly. Gently shake excess water from the filter. Be sure filter is thoroughly dry before replacing Or instead of washing, you may vacuum the filter clean.

Operating Instructions (continued) 4-WAY LOUVERS

The 4-Way air directional louvers allow you to direct the air flow Up or Down and Left or Right throughout the room as needed.

OCCURRENCE SOLUTION

Wall plug disconnected. Push plug firmly into wall outlet.

Plug Current Device Tripped. Press the RESET button.

House fuse blown or circuit breaker tripped. Replace fuse with time delay type or reset circuit breaker.

Control is OFF. Turn Control ON and set to desired setting.

Air conditioner will not operate.

Air conditioner cooling, but room is too warm - NO ice forming on cooling coil behind decorative front.

Dirty air filter - air restricted. Clean air filter. Refer to Care and Cleaning section.

Temperature is set too high. Set temperature to a lower setting.

Air directional louvers positioned improperly. Position louvers for better air distribution.

Front of unit is blocked by drapes, blinds, furniture, etc. - restricts air distribution. Clear blockage in front of unit.

Doors, windows, registers, etc. open - cool air escapes. Close doors, windows, registers, etc.

Unit recently turned on in hot room. Allow additional time to remove stored heat from walls, ceiling, floor and furniture.

Air conditioner turns on and off rapidly.

Dirty air filter - air restricted. Clean air filter.

Outside temperature extremely hot. Set FAN speed to a faster setting to bring air through cooling coils more frequently.

If These Solutions Fail, Call 1-800-944-9044(US)/1-800-265-8352(Canada) For Frigidaire Service.

Before You Call

Air conditioner cooling, but room is too warm - ice forming on cooling coil behind decorative front

Outdoor temperature below 60 F (16 C). To defrost the coil, set FAN ONLY mode.O O

Air filter may be dirty. Clean filter. Refer to Care and Cleaning section. To defrost, set to FAN ONLY mode.

Temperature is set too low for night-time cooling. To defrost the coil, set to FAN ONLY mode. Then, set temperature to a higher setting.

11

Room temperature below 60F (16C). Cooling may not occur until room temperature rises above 60F (16C).

Temperature sensing element touching cold coil, located behind air filter. Straighten away from coil.

Air from unit does not feel cold enough.

Compressor shut-off by changing modes. Wait approximately 3 minutes and listen for compressor to restart when set in the COOL mode.

Reset to a lower temperature.

Noise when unit is cooling. Air movement sound. This is normal. If too loud, set to lower FAN setting.

2009 Electrolux Home Products, Inc. All rights reserved.

Water dripping INSIDE when unit is cooling.

Improper installation. Tilt air conditioner slightly to the outside to allow water drainage. Refer to installation instructions or check with installer.

Water dripping OUTSIDE when unit is cooling.

Unit removing large quantity of moisture from humid room. This is normal during excessively humid days.

Room too cold. Set temperature too low. lncrease set temperature.

Window vibration - poor installation. Refer to installation instructions or check with installer.

Before calling for service, review this list. It may save you time and expense. This list includes common occurrences that are not the result of defective workmanship or materials in this appliance.

Major Appliance Limited Warranty

12

Exclusions 1. Products with original serial numbers that have been removed, altered or cannot be readily determined. This warranty does not cover the following:

2. Product that has been transferred from its original owner to another party or removed outside the USA or Canada. 3. Rust on the interior or exterior of the unit. 4. Products purchased "as-is" are not covered by this warranty. 5. Food loss due to any refrigerator or freezer failures. 6. Products used in a commercial setting. 7. Service calls which do not involve malfunction or defects in materials or workmanship, or for appliances not in ordinary household use or used other than in accordance with the provided instructions. 8. Service calls to correct the installation of your appliance or to instruct you how to use your appliance. 9. Expenses for making the appliance accessible for servicing, such as removal of trim, cupboards, shelves, etc., which are not a part of the appliance when it is shipped from the factory. 10. Service calls to repair or replace appliance light bulbs, air filters, water filters, other consumables, or knobs, handles, or other cosmetic parts. 11. Surcharges including, but not limited to, any after hour, weekend, or holiday service calls, tolls, ferry trip charges, or mileage expense for service calls to remote areas, including the state of Alaska. 12. Damages to the finish of appliance or home incurred during installation, including but not limited to floors, cabinets, walls, etc. 13. Damages caused by: services performed by unauthorized service companies; use of parts other than genuine Electrolux parts or parts obtained from persons other than authorized service companies; or external causes such as abuse, misuse, inadequate power supply, accidents, fires, or acts of God.

DISCLAIMER OF IMPLIED WARRANTIES; LIMITATION OF REMEDIES CUSTOMER'S SOLE AND EXCLUSIVE REMEDY UNDER THIS LIMITED WARRANTY SHALL BE PRODUCT REPAIR OR REPLACEMENT AS PROVIDED HEREIN. CLAIMS BASED ON IMPLIED WARRANTIES, INCLUDING WARRANTIES OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE, ARE LIMITED TO ONE YEAR OR THE SHORTEST PERIOD ALLOWED BY LAW, BUT NOT LESS THAN ONE YEAR. ELECTROLUX SHALL NOT BE LIABLE FOR CONSEQUENTIAL OR INCIDENTAL DAMAGES SUCH AS PROPERTY DAMAGE AND INCIDENTAL EXPENSES RESULTING FROM ANY BREACH OF THIS WRITTEN LIMITED WARRANTY OR ANY IMPLIED WARRANTY. SOME STATES AND PROVINCES DO NOT ALLOW THE EXCLUSION OR LIMITATION OF INCIDENTAL OR CONSE- QUENTIAL DAMAGES, OR LIMITATIONS ON THE DURATION OF IMPLIED WARRANTIES, SO THESE LIMITATIONS OR EXCLUSIONS MAY NOT APPLY TO YOU. THIS WRITTEN WARRANTY GIVES YOU SPECIFIC LEGAL RIGHTS. YOU MAY ALSO HAVE OTHER RIGHTS THAT VARY FROM STATE TO STATE.

If You Need Service

Keep your receipt, delivery slip, or some other appropriate payment record to establish the warranty period should service be required. If service is performed, it is in your best interest to obtain and keep all receipts. Service under this warranty must be obtained by contacting Electrolux at the addresses or phone numbers below.

This limited warranty only applies in the USA and Canada. In the USA, your appliance is warranted by Electrolux Major Appliances North America, a division of Electrolux Home Products, Inc. In Canada, your appliance is warranted by Electrolux Canada Corp. Electrolux authorizes no person to change or add to any obligations under this warranty. Obligations for service and parts under this warranty must be performed by Electrolux or an authorized service company. Product features or specifications as described or illustrated are subject to change without notice.

2009 Electrolux Home Products, Inc. All rights reserved.

Canada 1.800.265.8352

Electrolux Canada Corp. 5855 Terry Fox Way

Mississauga, Ontario, Canada L5V 3E4

USA 1.800.944.9044 Electrolux Major Appliances 10200 David Taylor Drive Charlotte, NC 28262

Your appliance is covered by a limited one-year warranty and a limited 2-5 year warranty on the sealed system (the compressor, condenser, evaporator and tubing). For one year from your original date of purchase, Electrolux will pay all costs for repairing or replacing any parts of this appliance that prove to be defective in materials or workmanship when such appliance is installed, used and maintained in accordance with the provided instructions. From the second to the fifth year from your original purchase date, Electrolux will repair or replace any parts in the Sealed Refrigeration System (compressor, condenser, evaporator and tubing) that prove to be defective in materials or workmanship. In years 2-5, the consumer will be responsible for diagnostic, labor and parts costs as well as any removal, transportation and reinstallation expenses which are incurred during service on components other than those covered under the Sealed Refrigeration System 5-year warranty.

Manualsnet FAQs

If you want to find out how the FFRS1022RE Frigidaire works, you can view and download the Frigidaire FFRS1022RE Owner's Guide on the Manualsnet website.

Yes, we have the Owner's Guide for Frigidaire FFRS1022RE as well as other Frigidaire manuals. All you need to do is to use our search bar and find the user manual that you are looking for.

The Owner's Guide should include all the details that are needed to use a Frigidaire FFRS1022RE. Full manuals and user guide PDFs can be downloaded from Manualsnet.com.

The best way to navigate the Frigidaire FFRS1022RE Owner's Guide is by checking the Table of Contents at the top of the page where available. This allows you to navigate a manual by jumping to the section you are looking for.

This Frigidaire FFRS1022RE Owner's Guide consists of sections like Table of Contents, to name a few. For easier navigation, use the Table of Contents in the upper left corner.

You can download Frigidaire FFRS1022RE Owner's Guide free of charge simply by clicking the “download” button in the upper right corner of any manuals page. This feature allows you to download any manual in a couple of seconds and is generally in PDF format. You can also save a manual for later by adding it to your saved documents in the user profile.

To be able to print Frigidaire FFRS1022RE Owner's Guide, simply download the document to your computer. Once downloaded, open the PDF file and print the Frigidaire FFRS1022RE Owner's Guide as you would any other document. This can usually be achieved by clicking on “File” and then “Print” from the menu bar.