Contents

Flir VS80 Kit Videoscope User Manual PDF

1 of 56
1 of 56

Summary of Content for Flir VS80 Kit Videoscope User Manual PDF

User Manual VS80 Kit High Performance Videoscope with Camera Probe

User Manual VS80 Kit

#NAS100101; r. AB/85156/85156; en-US iii

Table of contents

1 Advisories ..........................................................................1 1.1 Copyright ..................................................................1 1.2 Quality Assurance ......................................................1 1.3 Documentation ..........................................................1 1.4 Disposal of Electronic Waste.........................................1

2 Safety ................................................................................2 3 Introduction........................................................................4

3.1 Overview ..................................................................4 3.2 Product Features ........................................................5 3.3 Kit Descriptions..........................................................5 3.4 Ordering Videoscope and Probes Separately ...................6 3.5 Supplied Equipment (all kits) .........................................6 3.6 Supplied Equipment (select probes) ...............................6

4 Product Description ............................................................7 4.1 Front View.................................................................7 4.2 Top View...................................................................8 4.3 Right Side View..........................................................8 4.4 Back of Unit...............................................................9

5 Quick Start (en)................................................................. 10 6 Control Buttons ................................................................ 12

6.1 Control Buttons Overview........................................... 12 6.2 Button Descriptions................................................... 12

7 Touch Screen Icons ........................................................... 14 7.1 Touch-Screen Overview ............................................. 14 7.2 Visual Camera Touch-Screen Icons .............................. 14 7.3 IR Camera Touch-Screen Icons ................................... 16

8 Settings Menu................................................................... 19 8.1 Settings Menu Overview ............................................ 19 8.2 Menu Item Descriptions ............................................. 20

8.2.1 Probe Selection (visual cameras only) ................ 20 8.2.2 Language..................................................... 20 8.2.3 Wi-Fi Menu................................................... 21 8.2.4 Display Grid (visual cameras only) ..................... 21 8.2.5 Timestamp ................................................... 21 8.2.6 External Microphone....................................... 21 8.2.7 USB Card Reader .......................................... 22

#NAS100101; r. AB/85156/85156; en-US v

Table of contents

8.2.8 SD Card....................................................... 22 8.2.9 Image (visual cameras only) ............................. 23 8.2.10 Measurement Parameters (IR camera

only)............................................................ 23 8.2.11 Auto Power Off (APO) ..................................... 24 8.2.12 Date / Time................................................... 24 8.2.13 Recording Quality (visual cameras only).............. 25 8.2.14 Information (Info) ........................................... 25 8.2.15 Aspect Ratio (IR camera only) .......................... 26 8.2.16 Regulatory.................................................... 26

9 Image and Video Recording................................................ 27 9.1 Image and Video Basics............................................. 27 9.2 Media Gallery .......................................................... 27 9.3 Opened Images ....................................................... 28 9.4 Opened Videos ........................................................ 29 9.5 Recording Audio over Video........................................ 29 9.6 Downloading Media to a PC........................................ 30

10 Rechargeable Battery ........................................................ 31 10.1 Battery Overview...................................................... 31 10.2 Battery Status Icon.................................................... 31 10.3 Recharging the Battery .............................................. 31

11 Temperature Alarm (IR Camera) .......................................... 32 11.1 Alarms Overview ...................................................... 32 11.2 Configuring the Alarms .............................................. 32 11.3 Alarm Trigger Indication ............................................. 32

12 Wi-Fi Connectivity ............................................................. 34 12.1 Wi-Fi Overview ........................................................ 34 12.2 Connecting a Smart Device to the VS80 ........................ 34 12.3 Using the FLIR Tools App ........................................ 35

13 PC Interface...................................................................... 36 13.1 PC Interface Overview ............................................... 36 13.2 Connecting the VS80 to a PC ...................................... 36 13.3 Accessing the VS80 Directory on the PC ....................... 36

14 Firmware Updates ............................................................. 37 14.1 Obtaining the Firmware Update File .............................. 37 14.2 Moving the Upgrade File to the VS80 ............................ 38

#NAS100101; r. AB/85156/85156; en-US vi

Table of contents

14.3 Executing the Firmware Update ................................... 39 15 FCC and IC Notices ........................................................... 40 16 Specifications................................................................... 42 17 CUSTOMER SUPPORT ....................................................... 44 18 Warranty .......................................................................... 45

18.1 Three-Year Limited Warranty ....................................... 45

#NAS100101; r. AB/85156/85156; en-US vii

Advisories1

1.1 Copyright 2022 FLIR Systems, Inc. All rights reserved worldwide.

No parts of the software including source code may be reproduced, transmit- ted, transcribed or translated into any language or computer language in any form or by any means, electronic, magnetic, optical, manual or otherwise, without the prior written permission of FLIR.

The documentation must not, in whole or part, be copied, photocopied, repro- duced, translated or transmitted to any electronic medium or machine-read- able form without prior consent, in writing, from FLIR Systems, Inc. Names and marks appearing on the products herein are either registered trademarks or trademarks of FLIR Systems, Inc. and/or its subsidiaries. All other trade- marks, trade names or company names referenced herein are used for identi- fication only and are the property of their respective owners.

1.2 Quality Assurance The Quality Management System under which these products are developed and manufactured has been certified in accordance with the ISO 9001 stand- ard. FLIR Systems, Inc. is committed to a policy of continuous development; therefore, we reserve the right to make changes and improvements on any of the products without prior notice.

1.3 Documentation To access the latest manuals and notifications, go to the Download tab at: https://support.flir.com. It only takes a few minutes to register online. In the download area you will also find the latest releases of manuals for our other products, as well as manuals for our historical and obsolete products.

1.4 Disposal of Electronic Waste As with most electronic products, this equipment must be disposed of in an environmentally friendly way, and in accordance with existing regulations for electronic waste. Please contact your FLIR represen- tative for more details.

#NAS100101; r. AB/85156/85156; en-US 1

Safety2

CAUTION

Please read all user instructions and safety guidelines before proceeding.

If the equipment is used in a manner not specified by the manufacturer, the protection provided by the equipment may be impaired.

The battery is not user-serviceable. DO NOTopen the unit to replace the bat- tery or to perform maintenance. Contact FLIR if the unit needs servicing or a battery replacement.

WARNING

Risk of explosion if the battery is replaced using an incompatible battery type.

WARNING

Failure to use the device without observing the information provided next to the WARNING symbol may cause serious injury or loss of life.

CAUTION

Failure to use the device without observing the information provided next to the CAUTION label may cause damage to the product.

WARNING

HAZARDOUS ENVIRONMENTS

DO NOTuse this system in explosive environments including gasoline and alcohol storage tanks.

FLAMMABLE GASES

DO NOTuse this device near flammable gases.

FOR INDUSTRIAL USE ONLY

AVOID EYE INJURY

DO NOT look into the LED worklight or direct the worklight toward the eyes.

#NAS100101; r. AB/85156/85156; en-US 2

Safety2

CAUTION

INCOMPATIBLE SUBSTANCES MAY DAMAGE THE PROBE

See the probe user manual for a list of specified liquids into which the probe can be inserted.

#NAS100101; r. AB/85156/85156; en-US 3

Introduction3

3.1 Overview Thank you for selecting the VS80 High Performance Videoscope kit. The VS80 kit is a rugged, waterproof video inspection system that includes the VS80 Videoscope, a detachable camera probe, and accessories.

The VS80 works with a variety of cameras probes as listed in Section 3.3 and 3.4 below. VS80 probes are especially designed to perform well in difficult to reach locations and areas unsafe to approach. The probes provide sharp vid- eo and still images and can be safely submerged in fluids, as specified in the separate instructions provided with each probe.

CAUTION

Before putting the VS80 into operation there are two steps that must be performed immedi- ately after connecting the probe to the main unit:

1. Update the VS80 firmware, as explained in Section 14. 2. For visual probes only: Select the probe that you intend to use from the Probe Selec-

tion Settings menu list, as explained in Section 8. This does not apply when connect- ing an IR probe.

Failure to perform these steps will cause the VS80 to incorrectly identify the connected probe.

The VS80 is battery operated and its internal lithium battery can be charged by connecting the VS80 to an AC source using the supplied USB AC adaptor/ charger (see Section 10).

Still images and videos are stored on the supplied micro SD card, inserted in the VS80 right side compartment. Stored media can be downloaded to a PC using the USB-C port (see Sections 9 and 13).

#NAS100101; r. AB/85156/85156; en-US 4

Introduction3

3.2 Product Features Large display monitor shows camera images, touch-screen icons, settings

menu, and other information. Sun visor protects monitor and allows viewing in brightly lit areas. Image/video recording with micro SD card storage. PC interface for downloading images/video and updating firmware. Micro HDMI port for viewing images on an external monitor. Split screen shows forward/side view images simultaneously when using a

dual camera or a mirror accessory. Split-screen also compares live images with stored images. Wi-Fi connectivity for use with a smart device. FLIR Tools compatible for connecting with other FLIR cameras. Microphone/headset input for voice-over recording on videos. Internal rechargeable lithium battery runs 8 hours from a full charge. 3.3 Kit Descriptions KIT Order Numbers KIT Descriptions

VS80KIT-1 General Purpose Videoscope Kit with 5.5 mm 1 m long probe

VS80KIT-2 Videoscope Kit with 2-Way Articulation 4.5 mm 1 m long probe

VS80KIT-3 Videoscope Kit with Dual HD Camera 4.9 mm 1 m long probe

VS80KIT-4 Videoscope Kit with 4-Way Articulation 6.0 mm 2 m long probe

VS80KIT-5 Videoscope Kit with Plumbing Spool and 10 mm 25 m long probe

VS80KIT-6 Videoscope Kit with HD 5.5 mm 1 m long probe

VS80IR21 Videoscope Kit with IR Thermal 19 mm 1 m long probe

#NAS100101; r. AB/85156/85156; en-US 5

Introduction3

3.4 Ordering Videoscope and Probes Separately Order Numbers Descriptions

VS80 VS80 Videoscope Screen only (No Camera Probes)

VS80CIR-21 VS80 160 120 IR Thermal Camera Probe 19 mm 1 m (3.3 ft) long

VS80C551RM VS80 Camera Probe 5.5 mm 1 m (3.3 ft) long

VS80A2451RM VS80 2-way Articulating Camera Probe 4.5 mm 1 m (3.3 ft) long

VS80A4602RM VS80 4-way Articulating Camera Probe 6.0 mm 2 m (6.6 ft) long

VS80C1025RM VS80 Plumbing Spool and Camera Probe 10 mm 25 m (82 ft) long

VS80CHD-551RM VS80 HD Camera Probe 5.5 mm 1 m (3.3 ft) long

VS80C2491RM VS80 Dual HD Camera Probe 4.9 mm 1 m (3.3 ft) long

CAUTION

The probe in use must be selected from the list of probes in the Probe Selection settings menu. If this is not done, the VS80 will not operate correctly with your probe.

Always switch OFF the VS80 when swapping probes.

3.5 Supplied Equipment (all kits) VS80 High Performance Videoscope Camera probe Sun visor (removable and retractable) USB C to USB A charging and PC interface cable Power adaptor with AC plugs (for US, UK, EU, AUS) Micro HDMI audio-visual cable Audio headset Hand and neck straps Micro SD card (32 G) Printed Quick Start booklet Heavy duty carrying/shipping case 3.6 Supplied Equipment (select probes) Side-view and dual view mirror accessories for VS80C55-1RM and

VS80A4-602RM probes. Side-view mirror and centring tools for pipe inspection kit, VS80C1025RM.

#NAS100101; r. AB/85156/85156; en-US 6

Product Description4

4.1 Front View Note that not all display icons can be represented in Figure 4.1 at one time be- cause of differences in operational modes; display icons not shown here are explained in their relevant sections.

Figure 4.1 Front View of Monitor

1. Control buttons. See Section 6. 2. Status LED: Blue when power is on (charger not connected); green when

charging with power off; cyan (light blue) when charging with power on; no light when fully charged (with charger attached).

3. Probe connection. 4. Charging/PC interface USB-C port. 5. Compartment for reset button, micro SD card slot, micro HDMI port. 6. Audio headset/microphone connector (for recording audio over videos). 7. Temperature scale bar graph (IR camera). 8. Upper temperature range limit (IR camera). 9. Lower temperature range limit (IR camera). 10. Battery status icon. 11. Touch screen icons. 12. Camera images and menu screens.

#NAS100101; r. AB/85156/85156; en-US 7

Product Description4

4.2 Top View

Figure 4.2 Top View of Monitor

1. Neck and hand strap fasteners. One on each corner of the unit. 2. Probe connector. Line up the white dots on the probe connector and the

display unit connector when attaching the probe. 3. USB-C port for PC interface and battery charging. 4.3 Right Side View

Figure 4.3 Right Side View of Monitor

1. Compartment latch. Push latch upward to access the compartment (the compartment contains items 3, 4, and 5, listed below).

2. Audio connector (3.5 mm) for voice-over video recording using the sup- plied earpiece microphone.

3. Reset button. Press the recessed button for 2 seconds to reset the unit in the event of a system crash.

4. Micro SD card slot. Do not remove or replace the SD card while the VS80 is powered. Do not use cards that have been formatted by another camera or system.

5. Micro HDMI port for connecting an external monitor. Note that Wi-Fi is not operable when an external monitor is connected.

#NAS100101; r. AB/85156/85156; en-US 8

Product Description4

4.4 Back of Unit The tilt stand, tripod mount, and informational labels are located on the back of the VS80 (not pictured).

#NAS100101; r. AB/85156/85156; en-US 9

Quick Start (en)5

CAUTION

Before putting the VS80 into operation there are two steps that must be performed immedi- ately after connecting the probe to the main unit:

1. Update the VS80 firmware, as explained in Section 14. 2. For visual probes only: Select the probe that you intend to use from the Settings menu

list, as explained in Section 8. This does not apply when connecting an IR probe. Failure to perform these steps will cause the VS80 to misidentify the connected probe.

1. If the battery status icon is showing a low charge, or if the unit will not power up, connect the VS80 to an AC power source using the supplied AC adaptor/charger, the charger connects to the USB port located on the top of the display unit (see Section 10 for details).

2. Ensure that a micro SD card is inserted in the slot located in the right side compartment.

3. Carefully connect the camera probe as detailed below:

Figure 5.1 Connecting the probe to the monitor unit

Align the white dot on the probe connector with the dot on the display connector.

Carefully plug the probe into the display unit. Tighten the connecting collar to secure the probe connection. As mentioned, select the probe from the Settings menu list. See Sec-

tion 8. 4. Remove the protective lens cap from the camera probe. 5. Long press the power button, the FLIR logo will appear. 6. The camera image will then appear with touch-screen icons, battery status

icon, date/time, and color bar graph (IR camera).

#NAS100101; r. AB/85156/85156; en-US 10

Quick Start (en)5

7. To orient the camera, the IR probe includes a dot on the head to indicate the top of the image, as shown.

8. The front panel status LED (located above the control buttons) is blue when power is on (charger not connected); green when charging with power off; cyan (light blue) when charging with power on; no light when fully charged (with charger attached).

9. Long press the power button to switch off the VS80 after use.

#NAS100101; r. AB/85156/85156; en-US 11

Control Buttons6

6.1 Control Buttons Overview The physical control buttons are used in conjunction with the touch-screen icons to set up and operate the VS80. Similar to the touch-screen icons, sev- eral control buttons have extended capabilities that adapt to each probes features.

6.2 Button Descriptions

Figure 6.1 Control Buttons

1. Image Capture button. Short press to capture an image. Images are stored on the supplied micro SD card.

2. Video Record button. Short press to start or stop recording. Videos are stored on the supplied micro SD card. See Sections 9 and 13 for details on viewing and downloading media. See the Specifications (Section 16) for media formats and SD card information.

3. Zoom In / Menu + (plus) button. In normal operation for visual cameras only, short press the button to zoom in on the camera image. A slider graphic appears on the right side of the image showing 1x, 1.5x, 2x, and 3x zoom levels. When programming, this button can be used to increase a setting value or to move up a list.

#NAS100101; r. AB/85156/85156; en-US 12

Control Buttons6

4. Brightness decrease and left arrow button. Short press this button to decrease worklight brightness. A slider graphic appears on the left side of the image showing the brightness level. In some menus, this button can be used as a left arrow button.

5. Zoom Out / Menu (minus) button. In normal operation for visual cam- eras only, short press the button to zoom out on the camera image. A slider graphic appears on the right side of the image showing 1x, 1.5x, 2x, and 3x zoom levels. When programming, this button can be used to de- crease a setting value or to move down a list.

6. Brightness increase and right arrow button. Short press this button to increase worklight brightness. A slider graphic appears on the left side of the image showing the brightness level. In some menus, this button can be used as a right arrow button.

7. Full-screen view button. Short press to extend the image viewing area, short press to return to the default view. When Wi-Fi is active, this button is used to disconnect Wi-Fi.

8. Power / Return button. Long press to switch the VS80 on/off. Short press to return from a menu screen.

9. Settings menu button. Short press to open or exit the Settings menu. See Section 8 for details on settings menu options and navigation.

10. Image and Video Gallery. Short press to open the media gallery. Thumb- nails of stored media will appear. See Sections 9 and 13 for complete information.

#NAS100101; r. AB/85156/85156; en-US 13

Touch Screen Icons7

7.1 Touch-Screen Overview The touch-screen icons are used in conjunction with the physical control but- tons to configure and operate the VS80. See Section 6 for details on the con- trol buttons.

Touch-screen icons appear along the left and right side of the VS80 display for visual cameras, and only along the right side for IR cameras. An icon can be tapped to activate/deactivate a function or to open a submenu for further configuration.

7.2 Visual Camera Touch-Screen Icons A visual camera display example, with touch-screen icons, is provided below. The table below the camera image explains each touch-screen icon in detail. Tap an icon to enable/disable it or to open its submenu.

Note that camera probes are typically supplied with their own user manual, see the probe manual for additional information.

Figure 7.1 Digital Camera touch-screen icons shown on left and right side borders

ICON DESCRIPTION

Tap to switch the exposure compensation filter on or off. The filter gives detail and brightens dark areas in an image.

Tap to switch the LED worklight on or off.

Tap to show/hide a mirror image of the camera view.

#NAS100101; r. AB/85156/85156; en-US 14

Touch Screen Icons7

Tap to begin comparing stored images with the live camera feed on a split-screen. When you tap the icon, the image gallery opens. Select an image from the gallery to compare with the live image. The screen will split, showing the stored image and the live image side by side.

Additional touch-screen icons are active in this mode, see figure below.

1. Live image (default position: left) 2. Stored image (default position: right) 3. Tap the icon and drag the stored image as desired, tap icon when

done 4. Swap left and right images 5. Return to Gallery to select a different image 6. Selected area of image (see step 3 above)

Tap to rotate image clockwise (90, 180, and 270).

Tap to switch the dust elimination filter on or off (for use with dual cam- era models and mirror accessories).

For dual camera models and for single camera models using mirror ac- cessories, tap this icon to show a split screen with the forward facing (F) and side facing (S) views shown on a split screen.

Same as icon directly above but, when tapped, the worklight toggles di- rection from side to forward or from forward to side.

Tap to show the camera image in a negative contrast format. Tap again to return to normal operation.

Tap to open the white balance menu described below:

Default: Reset to the factory default. Calibration: Point to a white surface, tap the box in the centre of the

screen or press the check mark button, and then confirm. Custom: Set the White Balance manually using the RGB sliders.

#NAS100101; r. AB/85156/85156; en-US 15

Touch Screen Icons7

7.3 IR Camera Touch-Screen Icons An IR camera display example, with touch-screen icons, is provided below. The table below the camera image explains each touch-screen icon in detail. Tap an icon to open its submenu.

Note that camera probes are typically supplied with their own user manual, see the probe manual for additional information.

Figure 7.2 IR Camera touch-screen icons shown on right edge of display

ICON DESCRIPTION

Tap to open the rotate/flip image menu. Select a view from the list below.

1. Tap to rotate image per items 3, 4, 5, and 6. 2. Tap to view mirror image. 3. 90 clockwise rotation. 4. 180 clockwise rotation. 5. 270 clockwise rotation. 6. Normal view.

#NAS100101; r. AB/85156/85156; en-US 16

Touch Screen Icons7

Tap to open the color palette menu. Select from the options below.

1. Iron color palette. 2. Rainbow color palette. 3. Gray-scale palette. 4. Below alarm. Areas in the image that are below the temperature set point

are highlighted in blue (see Section 11). 5. Above alarm. Areas in the image that are above the temperature set point

are highlighted in red (see Section 11).

Measurement type:

CENTRE SPOT: Temperature of spot (identified by the displayed cross- hairs) is measured and shown on the upper left hand side of display.

COLD SPOT: The coldest temperature spot is targeted in the boxed re- gion of the image. The spot temperature is shown on the upper left side of the display. Tap and drag the box to move it, use the up/down/right/left navigation buttons (the four buttons that surround the centre check mark button) to re- size it, or pinch/stretch the box with two fingers to narrow or widen it.

HOT SPOT: The hottest temperature spot is targeted in the boxed region of the image. The spot temperature is shown on the upper left side of the dis- play. Tap and drag the box to move it, use the up/down/right/left navigation buttons (the four buttons that surround the centre check mark button), or pinch/stretch the box with two fingers to narrow or widen it.

NO MEASUREMENTS: Temperature is not measured.

#NAS100101; r. AB/85156/85156; en-US 17

Touch Screen Icons7

Tap to open the Auto/Manual Temperature Scale menu.

Auto Scale. The VS80 automatically selects the low to high temperature scale (range) based on the camera image. Use Auto in normal operation.

Manual scale. Use manual scaling to limit the temperature scale close to the targeted spot temperature. You can manually adjust the temperature range by first tapping the temperature readout at the top or bottom of the bar graph,

to enable editing, and then using the plus and minus buttons to adjust the value.

Tap to open the Measurement Parameters settings menu. Use the touch- screen up/down arrows to set Emissivity and/or Reflected Temperature.

Tap the desired temperature unit of measure or.

See Section 8.2.10 for additional details.

Note on Emissivity: For most applications, the default emissivity setting of 0.95 is a good place to start. For shiny, reflective surfaces, an emissivity ad- justment is likely needed. To learn more about emissivity, and how to adjust it, follow the link below.

Note on Reflected Temperature: Set the Reflected Temperature to the ambi- ent temperature in the test area, to start. If surrounding objects are interfering with your measurements, an adjustment to the Reflected Temperature setting may be needed. Refer to the link below for more information.

Emissivity and Reflected Temperature Information

#NAS100101; r. AB/85156/85156; en-US 18

Settings Menu8

8.1 Settings Menu Overview

Figure 8.1 Settings Menu example. Menu items vary depending on attached camera probe.

The Settings menu allows you to quickly and easily customize the VS80. Press the Settings button to open/close the menu. The menu has two pa- ges, tap the up/down arrow touch-screen icons to scroll. Tap a menu item to open it or to toggle its setting ON/OFF.

The menu is different for IR and visual cameras. See the table below. Detailed descriptions are provided, below, in Section 8.2.

MENU ITEMS VISUAL CAMERA IR CAMERA

PROBE SELECTION

LANGUAGE Wi-Fi

DISPLAYGRID

TIMESTAMP

EXTERNAL MICROPHONE

USB CARD READER

SD CARD

IMAGE

MEASUREMENT PARAMETERS

APO

DATE / TIME

RECORDING QUALITY

INFO

#NAS100101; r. AB/85156/85156; en-US 19

Settings Menu8

ASPECT RATIO

REGULATORY

8.2 Menu Item Descriptions Each menu item is detailed below.

8.2.1 Probe Selection (visual cameras only) Tap to open the Probe Selection menu.

Figure 8.2 Probe Selection Settings Menu

Tap the probe model number (2) that matches the probe you are using. This will ensure optimal probe compatibility with the VS80. The touch-screen icons and control buttons will adapt to each selection. Tap the up/down arrow icons (3) to scroll pages. Tap the left arrow (1) to return to the main menu.

8.2.2 Language Tap to open the Language menu.

Figure 8.3 Language Settings Menu

Tap the desired language (2). Tap the up/down arrow icons (3) to scroll pages. Tap the left arrow (1) to return to the main menu.

#NAS100101; r. AB/85156/85156; en-US 20

Settings Menu8

8.2.3 Wi-Fi Menu The Wi-Fi utility allows you to connect the VS80 with a smart device, see Sec- tion 12 for complete information. The items listed below provide a basic over- view of the Wi-Fi menu options:

Set Wi-Fi ON/OFF. View the SSID (Service Set Identifier) number. The SSID is the identifier

for all of the networks currently within range. Create a password (up to 16 characters) using the touch-screen keyboard.

Tap the SETTINGS box to open the password menu. 8.2.4 Display Grid (visual cameras only) Tap ON or OFF to enable or disable the Display Grid. Each block in the grid represents one square 0.2 in (0.5 cm) area. Tap the unit of measure on the screen to toggle imperial and metric units.

Figure 8.4 Display Grid. Image on left shows Imperial units selected; Image on right shows Metric units selected.

The grid is superimposed over the camera image to give dimensional context to the area under inspection.

8.2.5 Timestamp Tap ON or OFF to enable or disable the timestamp option. When enabled, time and date are saved with each image and video.

8.2.6 External Microphone Tap ON or OFF to enable or disable the external microphone function. Attach the supplied microphone earpiece to the 3.5 mm connector on the meters right side. Use the VOLUME slider to set the microphone input volume from 1 to 10, or press DEFAULT to set the volume to 5. Audio narrative can then be recorded with each video.

#NAS100101; r. AB/85156/85156; en-US 21

Settings Menu8

8.2.7 USB Card Reader There are no programmable settings to adjust in this menu. The menu text

turns from grey to white, and the USB icon appears, when the VS80 is con- nected to a PC. While connected, you can move images and video from the SD card to a PC and update the VS80 firmware. See Section 13, for PC inter- face information, and Section 14, for firmware updating.

8.2.8 SD Card Tap SD CARD to open the menu.

Figure 8.5 SD Card Settings Menu

The available memory for images only (2), video only (3), and total memory (4) is displayed. You can delete all files by tapping DELETE ALL FILES (5) or you can format a new SD card by tapping FORMAT SD CARD (6). Tap the left arrow (1) to return to the main menu.

Do not use SD cards that were formatted on another device, as the filing sys- tems may differ. Always format SD cards with the VS80 before use (the sup- plied card is formatted at the factory).

For additional SD card information, see the Specifications (Section 16).

#NAS100101; r. AB/85156/85156; en-US 22

Settings Menu8

8.2.9 Image (visual cameras only) Tap to open the Image Brightness, Contrast, and Sharpness control menu.

Figure 8.6 Image Settings Menu

Tap and drag the sliders (2) as desired. Tap DEFAULT (3) to reset the image settings. Tap the left arrow (1) to return to the main menu.

8.2.10 Measurement Parameters (IR camera only) Tap to open the Measurement Parameters menu.

Figure 8.7 Measurement Parameters Settings Menu

Program the Emissivity (2) and Reflected Temperature (3) values using the up/down touch-screen icons. Select the unit of measure by tapping or (4). Tap the left arrow (1) to return to the main menu.

Note on Emissivity: For most applications, the default emissivity setting of 0.95 is a good place to start. For shiny, reflective surfaces, an emissivity ad- justment is likely needed. To learn more about emissivity, and how to adjust it, follow the link below.

#NAS100101; r. AB/85156/85156; en-US 23

Settings Menu8

Note on Reflected Temperature: Set the Reflected Temperature to the am- bient temperature in the test area, to start. If surrounding objects are interfer- ing with your measurements, an adjustment to the Reflected Temperature setting may be needed. Refer to the link below for more information.

Emissivity and Reflected Temperature Information

8.2.11 Auto Power Off (APO) Tap to open the APO menu.

Figure 8.8 APO Settings Menu

To set APO, tap 5, 10, 20, 30 minutes (3) or Disable (2). Tap the left arrow (1) to return to the main menu.

8.2.12 Date / Time Tap to open the Date/Time menu.

Figure 8.9 Date/Time Settings Menu

Use the touch-screen arrows to set the date (2) and the time (3). Tap the up/ down arrows (4) to select the display format for month (MM), day (DD), and

#NAS100101; r. AB/85156/85156; en-US 24

Settings Menu8

year (YY): MM/DD/YY, DD/MM/YY, or YY/MM/DD. Tap the up/down arrows (5) to select the 12 or 24 hour clock. Tap the left arrow (1) to return to the main menu.

8.2.13 Recording Quality (visual cameras only) This setting applies to video recording only. Tap to open the Recording Quality menu.

Figure 8.10 Recording Quality Settings Menu

Tap Normal or High Quality (2). In Normal mode, video is recorded at a rate of 1 M bits/s (megabits per second), in High Quality mode the bit rate is 2 M bits/ s. Tap the left arrow (1) to return to the main menu. The higher quality mode will result in file sizes proportionately larger than those of normal quality.

8.2.14 Information (Info) Tap to open the Information menu.

Figure 8.11 Information Settings Menu

View the firmware version (2) and serial number (3). Tap FIRMWARE UP- GRADE (4) to upgrade the VS80 firmware. Tap FACTORY DEFAULT (5) to

#NAS100101; r. AB/85156/85156; en-US 25

Settings Menu8

reset all user programmable settings. See Section 14 for details on firmware upgrading. Tap the left arrow (1) to return to the main menu.

8.2.15 Aspect Ratio (IR camera only) Tap to select a 4:3 or 16:9 aspect ratio. This setting does not affect the re- corded images and video, only the display is affected. Selecting 16:9 will ex- pand the thermal image to fit the width of the screen. Selecting 4:3 will present the thermal image in the centre of the screen.

8.2.16 Regulatory Tap this item to view safety verifications and regulatory compliance certifications.

Figure 8.12 Regulatory information

#NAS100101; r. AB/85156/85156; en-US 26

Image and Video Recording9

9.1 Image and Video Basics The VS80 allows you to capture still images (.jpg) and video (.mov). Press the image capture button to save still images and press the video record but- ton to start/stop video recording.

With a connected microphone, you can record narration audio with videos. See the Specifications (Section 16) for image and video file resolution information.

Media are stored on the supplied micro SD card (inserted in the right-side compartment). For information regarding the number of images and length of video that can fit on a variety of SD card sizes, see the Specifications (Section 16).

Images and video can be downloaded to a PC using the USB connector at the top of the VS80, see Sections 9.6 and 13.

9.2 Media Gallery Once images and video are recorded you can view them directly in the VS80 media gallery by pressing the Gallery button . In the gallery, tap the Image icon or the Video icon , to select a media type to browse. Tap a thumb- nail to open the image or video. Refer to the call-out below for more details.

Figure 9.1 Media Gallery

1. If the timestamp option is enabled in the Settings menu, media will include the date and time.

2. Selected thumbnails filename.

#NAS100101; r. AB/85156/85156; en-US 27

Image and Video Recording9

3. Selected thumbnails timestamp. 4. Up arrow. Scroll gallery pages. 5. Down arrow. Scroll gallery pages. 6. Selected page (top number) and total number of pages (bottom number). 7. Delete the selected image or video. 8. Tap to show only image thumbnails. 9. Tap to show only video thumbnails. 10. Tap arrow to return to exit the gallery. 9.3 Opened Images When you tap an image thumbnail, the image will open on the VS80 display. While the image is opened, you can type text onto the image, delete the im- age, and perform other actions as described in the call-out below.

Figure 9.2 Opened Image in Media Gallery

1. Tap the comments icon and type a comment using the touch-screen keyboard that appears; tap DONE on the keyboard when finished. Delete comments by tapping the eraser icon or open the keyboard again to amend comments, by pressing the keyboard icon . When satisfied with your comment, tap the disc icon to save the comments with the image.

2. Image timestamp. 3. Up arrow to scroll to next image. 4. Image filename. 5. Down arrow to scroll to prior image. 6. Tap trash icon to delete image. 7. Tap to view image thumbnails. 8. Tap to view video thumbnails. 9. Return to the main thumbnail gallery.

#NAS100101; r. AB/85156/85156; en-US 28

Image and Video Recording9

9.4 Opened Videos When you tap a video thumbnail, the video will open on the VS80 display. While the image is opened, press the play icon () to start the video and press the pause (||) icon to pause/stop the video. You can perform other actions as described in the call-out below.

Figure 9.3 Opened Video in Media Gallery

1. Video playback. 2. Video timestamp. 3. Up arrow to scroll to next video. 4. Video filename. 5. Down arrow to scroll to prior video. 6. Playback volume control. Use the +/- buttons (located above/below the

button). 7. Video time-line. 8. Play/Pause icons appear here. 9. Tap the trash icon to delete the video. 10. Tap to view image thumbnails. 11. Tap to view video thumbnails. 12. Return to main thumbnail gallery. 9.5 Recording Audio over Video Voice-over recordings can be combined with videos by plugging the supplied microphone earpiece into the 3.5 mm connector on the right side of the VS80 (below the side compartment).

#NAS100101; r. AB/85156/85156; en-US 29

Image and Video Recording9

Activate the microphone function in the Settings menu. Press to access the menu, scroll to the External Microphone setting, and tap ON. Set the mi- crophone volume level (1 to 10) using the on-screen slider or tap DEFAULT to set the microphone volume to 5. Now, each time you record video, you can add a narrative audio track that can be heard upon playback.

9.6 Downloading Media to a PC The VS80 is equipped with a PC interface. Connect the supplied USB cable to the VS80 USB port, located under the flap at the top of the unit, and to a PC USB port.

The VS80 will be recognized by the PC as a new external storage drive.

Simply drag files out of, and into (in the case of firmware upgrades), the VS80 drive. Media files are located in the MEDIA folder, the firmware file must be kept in the root directory, not in a folder. See Sections 13 and 14 for additional information regarding the PC interface and firmware updates.

#NAS100101; r. AB/85156/85156; en-US 30

Rechargeable Battery10

10.1 Battery Overview The VS80 is supplied with an internal, rechargeable lithium battery. The bat- tery icon on the upper right hand corner of the display provides battery status (see Section 10.2). The battery cannot be replaced or serviced in the field, please contact FLIR support for assistance. The VS80 can operate for 8 hours from a full charge (at room temperature).

10.2 Battery Status Icon The battery status icon is shown on the upper right hand corner of the VS80 display.

Figure 10.1 Battery status icon stages

In the figure above, the battery is fully charged in image no. 1. In images 2 and 3 the battery energy is decreasing until it is depleted in image no. 4. Im- age no. 5 shows the icons appearance when the VS80 is actively charging. Just before the battery expires, the display will show a large battery icon in the centre of the screen. The unit must be charged at this point.

10.3 Recharging the Battery A USB-C cable is supplied and is used to connect the VS80 (top USB port) to the supplied AC adaptor/charger. Connect the adaptor to an AC power source to charge. The AC charger is rated for 100 to 240 VAC (50/60 Hz) and inter- national power adaptors are supplied (for US, UK, EU, AUS). The VS80 will al- so charge while connected to a PC, but the charge time increases. The time required to fully charge the battery, from a low battery condition, is typically 3.5 hours using the AC adaptor.

#NAS100101; r. AB/85156/85156; en-US 31

Temperature Alarm (IR Camera)

11

11.1 Alarms Overview For the IR camera, the VS80 offers a high (above) and a low (below) alarm function; only one can be selected at a time.

11.2 Configuring the Alarms

1. Tap the color palette touch-screen icon .

2. Tap the Above alarm icon or the Below alarm icon . 3. The temperature set point will appear at the centre left area of the monitor

(as shown in Figure 11.1 as 77.1). 4. Tap and drag the color temperature bar graph up or down to change the

set point. The bar graph is located on the left side of the display, as shown in Figure 11.1, below).

11.3 Alarm Trigger Indication In the Above alarm mode, a red color is applied to all parts of the image that represent a temperature above the alarm set point. Some further adjustment to the set point may be necessary to achieve the proper contrast. Tap and drag on the color bar graph to change the set point.

Figure 11.1 Above Alarm display

#NAS100101; r. AB/85156/85156; en-US 32

Temperature Alarm (IR Camera)11

In Below alarm mode, a blue color is applied to all parts of the image that rep- resent a temperature below the alarm set point. Some further adjustment to the set point may be necessary to achieve the proper contrast. Tap and drag on the color bar graph to change the set point.

Figure 11.2 Below Alarm display

#NAS100101; r. AB/85156/85156; en-US 33

Wi-Fi Connectivity12

12.1 Wi-Fi Overview You can join the VS80 Wi-Fi network with your smart device by first switching the Wi-Fi function ON in the VS80 Settings menu and then selecting the VS80 network from your smart device.

For security, when you join the VS80 Wi-Fi network on your smart device you automatically disconnect from your commercial or residential network. You can also set up a password, as explained in the next section, to restrict ac- cess to the VS80 network.

12.2 Connecting a Smart Device to the VS80

1. Open the VS80 settings menu by pressing the Settings button . 2. TapWi-Fi to open the sub-menu. 3. To set a password, tap SETTINGS, type a password, and tap DONE. To

continue without password protection skip this step.

Figure 12.1 Touch-screen keyboard

4. Tap the ON/OFF touch-screen icon to switch on the Wi-Fi network. The Wi-Fi connection screen will appear, showing the 60 second timer, SSID, and password (see Figure 12.2).

Figure 12.2 Wi-Fi Connecting Screen

5. To abort the connection process, press the check button or tap the icon on the upper right hand corner of the display (item 2 in Figure 12.2).

#NAS100101; r. AB/85156/85156; en-US 34

Wi-Fi Connectivity12

6. Tap the VS80 from the list of available networks on your smart device be- fore the 60 second timer counts down. See Figure 12.3 below for example smart device screens.

7. When successfully connected, the Wi-Fi icon will appear at the top right of the VS80 display.

8. To disconnect Wi-Fi at any time, select OFF from the Wi-Fi Setting menu or press the button.

Figure 12.3 Smart device setup example. Step 1, tap the Wi-Fi setting on your smart de- vice. Step 2, tap the VS80 from the list of available networks. Step 3, note that the VS80 is now the connected network and your personal network (My Network, in this example) is now in the available network list, but it is no longer connected. To return to your network, simply tap your network name from the available networks (the VS80 will disconnect).

12.3 Using the FLIR Tools App With FLIR Tools, you can view live VS80 camera images and video on your smart device. You can also download previously recorded images and video from the VS80 to the smart device. You cannot, however, capture a new image or record a new video from the smart device, those actions can only be per- formed using the control buttons on the VS80.

Follow these steps to set up FLIR Tools for the VS80 on your smart device:

1. Download and install FLIR Tools on the smart device. 2. Connect the smart device to the VS80 network via Wi-Fi, per the directions

in Sections 12.1 and 12.2, above. 3. Open FLIR Tools on the smart device. 4. Select the VS80 Wi-Fi network, from the list of available networks, on the

smart device.

#NAS100101; r. AB/85156/85156; en-US 35

PC Interface13

13.1 PC Interface Overview The VS80 PC interface utility allows you to download images and video to your PC, see Section 9.

The PC interface also allows you to upgrade the VS80 firmware, see Section 14.

When connected to a PC, the VS80 also charges its battery. For quicker charging, connect the VS80 to an AC power source using the supplied AC adaptor and USB cable, see Section 10.

13.2 Connecting the VS80 to a PC The VS80 is supplied with a USB-C to USB-A cable, connect the USB-C end of the cable to the USB port at the top of the VS80 (to the right of the probe connection) and the other end to the PC USB-A port. Depending on the type of USB port on your PC, you may need to use a USB adaptor to connect correctly.

Figure 13.1 Connect the VS80 to a PC using the supplied USB-C (VS80 port) to USB-A (PC port) cable.

13.3 Accessing the VS80 Directory on the PC When successfully connected, the PC will show a newly connected VS80 drive. Open the drive to see its root directory which contains the firmware file and a set of folders. The Media folder is where images and videos, captured by the VS80, are stored. There may be other folders present that are for sys- tem use only.

You can then move images and video from the Media folder onto your PC hard drive.

The VS80 root directory is where you place firmware update files. See Section 14 for firmware upgrade details.

#NAS100101; r. AB/85156/85156; en-US 36

Firmware Updates14

To update the VS80 firmware, carefully follow the steps in the following sec- tions. The FLIR website is updated periodically to make improvements and so the screen examples, below, may not match the current format or configura- tion exactly. If you need assistance please contact FLIR support.

14.1 Obtaining the Firmware Update File 1. Go to the support site: https://support.flir.com 2. Click on the DOWNLOADS menu heading, as shown.

Figure 14.1 Click DOWNLOADS.

3. Click Software and Firmware as shown.

Figure 14.2 Click the Software and Firmware item from the options list.

4. Type your Email Address to log in or to create an account, as shown. Click Continue.

#NAS100101; r. AB/85156/85156; en-US 37

Firmware Updates14

5. For Figure 15.3, below, 1. Type VS80 in the search field; 2. Select FLIR / Extech Meters Software from the pull-down menu; 3. Select FLIR Soft- ware from the pull-down menu; 4. Click SEARCH; 5. Click the update file to download it to your PC.

Figure 14.3 Follow the steps to complete the download process.

14.2 Moving the Upgrade File to the VS80 1. As explained in Section 13, PC Interface, connect the VS80 to the PC us-

ing the supplied USB cable. 2. When the VS80 is physically connected to the PC, the PC should recog-

nize the VS80 as an external storage drive. For Windows, the VS80 drive will be given a drive letter in File Explorer (E:, for example). For Mac, the VS80 drive icon will appear on the desktop.

3. Drag the downloaded firmware file from your PC to the root (top level) di- rectory of the VS80 as shown in the Windows example below in Figure 15.4. NOTE Drag only the update file (FLIRVS80.BRN, for example) into the VS80 root directory. Do not drag other files or folders that may accompany the update file (readme.txt, for example).

Rename the existing firmware file to FLIRVS80-old.BRN, before loading the new update file. This will allow you to revert to the earlier firmware version if necessary.

4. Safely eject the VS80 from the PC (for Windows, right-click the drive letter in File Explorer and select Eject; For Mac, drag the drive icon into the Trash).

5. Physically disconnect the VS80 from the PC.

#NAS100101; r. AB/85156/85156; en-US 38

Firmware Updates14

Figure 14.4 Windows PC example: Moving the update file to the VS80 root directory.

14.3 Executing the Firmware Update 1. With the VS80 disconnected from the PC, press the VS80 Settings button

to open the Settings menu. 2. Navigate to the INFO menu, tap INFO to open it, and then tap FIRMWARE

UPGRADE; confirm the action when prompted. 3. Depending on the specific firmware, the VS80 may automatically cycle

power and restart with the new firmware active, or you may have to man- ually restart the VS80 after it switches off.

4. After restarting, verify that the new firmware version number is displayed in the INFO settings menu.

5. If you have questions, or run into problems upgrading, please contact FLIR (see Section 17, Customer Support).

#NAS100101; r. AB/85156/85156; en-US 39

FCC and IC Notices15

This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:

This device may not cause harmful interference.

This device must accept any interference received, including interference that may cause undesired operation.

FCC and IC Identification Numbers

FCC identification number: 2AXRO-VS80

IC identification number: 5306A-VS80

Federal Communications Commission Statement

This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment. This equipment gen- erates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instruction manual, may cause harmful interfer- ence to radio communications. Operation of this equipment in a residential area is likely to cause harmful interference in which case the user will be re- quired to correct the interference at his own expense.

FCC Caution: Any changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate this equipment.

RF Exposure Warning

This equipment must be installed and operated in accordance with provided instructions and the antenna(s) used for this transmitter must be installed to provide a separation distance of at least 20 cm (7.9 in) from all persons and must not be co-located or operating in conjunction with any other antenna or transmitter. End-users and installers must be provided with antenna installa- tion instructions and transmitter operating conditions for satisfying RF expo- sure compliance.

Canada, avis d'Industry Canada (IC)

#NAS100101; r. AB/85156/85156; en-US 40

FCC and IC Notices15

Cet appareil est conforme avec Industrie Canada exemptes de licence RSS standard(s).

Son fonctionnement est soumis aux deux conditions suivantes : (1) cet appa- reil ne doit pas causer d'interfrence et (2) cet appareil doit accepter toute in- terfrence, notamment les interfrences qui peuvent affecter son fonctionnement.

Radio Frequency (RF) Exposure Information

The radiated output power of the Wireless Device is below the Industry Cana- da (IC) radio frequency exposure limits. The Wireless Device should be used in such a manner such that the potential for human contact during normal op- eration is minimized.

This device has also been evaluated and shown compliant with the IC RF Ex- posure limits under mobile exposure conditions. (antennas are greater than 20 cm (7.9 in) from a person's body).

Informations concernant l'exposition aux frquences radio (RF)

La puissance de sortie mise par lappareil de sans fil est infrieure la limite d'exposition aux frquences radio d'Industry Canada (IC). Utilisez lappareil de sans fil de faon minimiser les contacts humains lors du fonctionnement normal.

Ce priphrique a galement t valu et dmontr conforme aux limites d'exposition aux RF d'IC dans des conditions d'exposition des appareils mo- biles (antennes sont suprieures 20 cm partir du corps d'une personne).

#NAS100101; r. AB/85156/85156; en-US 41

Specifications16

Monitor 7 in (17.8 cm) diagonal color touch-screen (1024 * 600)

Stored images file format

HD and other visual camera probes: .jpg (1280 * 720)

Thermal camera probe: .jpg (640 * 480)

Comments can be added directly onto images in the Media Gallery

Stored video file format HD and other visual camera probes: .mov (1280 * 720)

Thermal camera probe: .mov (640 * 480)

Selectable video recording quality (Settings menu)

Audio can be recorded over video using supplied headset microphone

Media storage capacity 32 G micro SD card (supplied); 64 G maximum size.

SD card capacity examples:

4 GB: total images 31,130; video length: 135 minutes

8 GB: total images 62,259; video length: 270 minutes

16 GB: total images 124,518; video length: 539 minutes

32 GB: total images 249,037; video length: 1079 minutes

Larger SD card sizes will accommodate proportionately longer video lengths and image totals.

Note that the video lengths listed above apply to the Normal recording mode (Settings menu); Selecting the High Quality recording mode will shorten the available lengths.

Connectivity USB 2.0 for PC interface and battery charging

FLIR Tools compatible

Wi-Fi connection to smart devices (802.11 b/g/n) with a 10 m distance limit

Micro HDMI connection for displaying camera images on an external monitor (NTSC / PAL compatibility)

3.5 mm audio headset connection

IR Probe Measurement Range

14 to 752 (-10 to 400); OL is displayed when IR tem- perature measurement is out of range

Visual Probe Depth of Field

10 mm to infinity

#NAS100101; r. AB/85156/85156; en-US 42

Specifications16

Operating temperature 14 to 140 (10 to 60) on battery power

32 to 104 (0 to 40) when connected to charger

Storage temperature -4 to 140 (20 to 60)

Relative humidity 10 to 95%, non-condensing

Altitude 6562 ft (2000 m)

Dimensions (VS80 Videoscope)

9.8 x 6.0 x 2.0 in (248 x 150 x 51 mm)

Weight (VS80 Videoscope)

2.86 lbs (1.3 kg)

Power supply Rechargeable lithium ion battery (9800 mAh)

3.5 hours charging and 8 hours operation at 79 (26)

AC adaptor/charger (supplied) for US, UK, EU, and AUS plugs. Output is rated 100 to 240 VAC 10%, 50/60 Hz. Input is rated 5.0 V DC, 3.0 A

Dust and water protection

IP 54 rated for display unit console

Drop-proof 6.6 ft (2 m)

Approved liquids for camera probe immersion

See separate instructions provided with probe or contact FLIR support

Safety Compliance IEC / EN 61010 or 62368; IEC 62471

Hazardous substance compliance

WEEE 2012/19/EU

RoHs 2011/65/EU

REACH Regulation EC 1907/2006

CA 65

EMC compliance EN 61000-6-2:2005 (Immunity)

EN 61000-6-3:2011 (Emission)

FCC Title 47 part 15, sub-part B

EN 301489-1/17

RF compliance EN 300328

EN 62479 (MPE)

IC and FCC Part 15 C (15.247)

#NAS100101; r. AB/85156/85156; en-US 43

CUSTOMER SUPPORT17

The FLIR support site, address below, is your resource for obtaining firmware upgrade files, latest versions of user manuals, customer service, and other product and accessory information.

Have the probe(s) and main unit serial numbers handy when contacting our support staff. Serial numbers are printed on white labels attached to each probe. The VS80 serial number is found on the back of the product and in the Settings menu.

https://support.flir.com

#NAS100101; r. AB/85156/85156; en-US 44

Warranty18

18.1 Three-Year Limited Warranty This product is protected by FLIRs 3-Year Limited Warranty. Visit www.flir.com/testwarranty to read the 3-Year Limited Warranty document.

#NAS100101; r. AB/85156/85156; en-US 45

#NAS100101; r. AB/85156/85156; en-US 46

last page

Publ. No.: NAS100101 Release: AB Commit: 85156 Head: 85156 Language: en-US Modified: 2022-05-19 Formatted: 2022-05-19

Website http://www.flir.com Customer support http://support.flir.com Copyright 2022, FLIR Systems, Inc. All rights reserved worldwide. Disclaimer Specifications subject to change without further notice. Models and accessories subject to regional market considerations. License procedures may apply. Products described herein may be subject to US Export Regulations. Please refer to exportquestions@flir.com with any questions.</

Manualsnet FAQs

If you want to find out how the VS80 Kit Flir works, you can view and download the Flir VS80 Kit Videoscope User Manual on the Manualsnet website.

Yes, we have the User Manual for Flir VS80 Kit as well as other Flir manuals. All you need to do is to use our search bar and find the user manual that you are looking for.

The User Manual should include all the details that are needed to use a Flir VS80 Kit. Full manuals and user guide PDFs can be downloaded from Manualsnet.com.

The best way to navigate the Flir VS80 Kit Videoscope User Manual is by checking the Table of Contents at the top of the page where available. This allows you to navigate a manual by jumping to the section you are looking for.

This Flir VS80 Kit Videoscope User Manual consists of sections like Table of Contents, to name a few. For easier navigation, use the Table of Contents in the upper left corner.

You can download Flir VS80 Kit Videoscope User Manual free of charge simply by clicking the “download” button in the upper right corner of any manuals page. This feature allows you to download any manual in a couple of seconds and is generally in PDF format. You can also save a manual for later by adding it to your saved documents in the user profile.

To be able to print Flir VS80 Kit Videoscope User Manual, simply download the document to your computer. Once downloaded, open the PDF file and print the Flir VS80 Kit Videoscope User Manual as you would any other document. This can usually be achieved by clicking on “File” and then “Print” from the menu bar.