Contents

Flir VS80 Kit Videoscope Quick Start PDF

Download download
Flir VS80 Kit Videoscope Quick Start PDF
Flir Manual Flir Videoscope Manual Flir VS80 Kit Manual Flir Videoscope Quick Start
Pages 8
Year 2022
Language(s)
English en
1 of 8
1 of 8

Summary of Content for Flir VS80 Kit Videoscope Quick Start PDF

Page 1

Quick Start VS80 KIT High Performance Videoscope and Camera Probe

Page 2

Quick Start (en) INTRODUCTION The VS80 kit consists of the main display unit, a camera probe, and accessories. To obtain the comprehensive user manual, additional quick start translations, firmware updates, and customer support, see the Support section. Please upgrade the firmware before use for optimal performance and camera compatibility.

The numbers in parenthesis, below, refer to the items listed in the Product Description section. QUICK STEPS

1. Insert micro SD card in slot located in side compartment (19). 2. Connect the camera probe (16):

3. Remove the cameras protective lens cap. 4. Long press the power button (9), the FLIR logo will appear. 5. The camera image will then appear (14) with touch-screen

icons (12) bordering the image. 6. For the IR camera only, the dot on the probe head indicates the

top of the image, as shown:

7. If the battery icon (15) indicates a low charge, connect the sup- plied AC adapter to the USB port at the top of the display unit (17) and to an AC power source (100 to 240 VAC, 50/60 Hz).

8. The status LED (1) is blue when power is on (charger not con- nected); green when charging with power off; cyan (light blue) when charging with power on; no light when fully charged (with charger attached).

9. Long press the power button (9) to switch off the VS80.

#NAS100100; r. AC/83794/84876; en-US 1

Page 3

PRODUCT DESCRIPTION

1. Power status LED 2. Image capture button 3. Video recording start/stop button 4. 1. Full screen view button; 2. Disconnect Wi-Fi 5. Zoom in (navigate upward in touch-screen menus) 6. Zoom out (navigate downward in touch-screen menus) 7. Decrease brightness (move left in touch-screen menus) 8. Increase brightness (move right in touch screen menus) 9. Long press to power on/off. Short press to return from a menu 10. Settings menu button 11. Image/video gallery button 12. Touch screen icons 13. Temperature scale (IR only) 14. Camera images and menus 15. Battery status icon 16. Probe connection 17. PC interface/charger USB-C port 18. Neck and hand strap fasteners 19. Compartment for reset button, SD card, HDMI port 20. Microphone connector (3.5 mm) Tilt stand, tripod mount (back of unit), and sun visor are not pictured.

#NAS100100; r. AC/83794/84876; en-US 2

Page 4

SETTINGS MENU Press the Settings button to open or close the menu. The menu has two pages, tap the up/down ( ) touch-screen arrows to scroll. Tap an item to open it or to enable/disable it.

Menu items are briefly described below. For complete information, please refer to the online user manual.

Wi-Fi Switch Wi-Fi on/off, set password (settings icon), and view the SSID.

DISPLAYGRID Enable/disable the display measurement grid. Digital cameras only

TIMESTAMP Enable to include date and time with recorded images and video.

EXTERNAL MICROPHONE Enable microphone to record voice-overs on- to video.

USB CARD READER Connect to a PC via USB to share images/ video and to update firmware (INFO menu).

SD CARD View memory status, format card, and delete all images/video.

IMAGE Set display brightness, contrast, and sharp- ness. Digital cameras only

MEASUREMENT PARAMETERS

Set emissivity, reflected temperature, and temperature units. IR camera only

AUTO POWER OFF Disable or set to 5, 10, 20, or 30 minutes.

DATE / TIME Set and format the calendar clock.

LANGUAGE Select local language.

RECORDING QUALITY (VIDEO)

Set to Normal (1 M bits/s) or High Quality (2 M bits/s). Digital cameras only

PROBE SELECTION Select the probe that you are using from the list. Digital cameras only

#NAS100100; r. AC/83794/84876; en-US 3

Page 5

INFO View firmware version, upgrade firmware, and revert settings to factory default.

ASPECT RATIO IR camera only. Toggle 4:3 and 16:9 display formats.

DIGITAL CAMERATOUCH SCREEN ICONS Tap an icon to enable/disable it or to open its submenu. Refer to the probes user manual for more information.

Switch the exposure com- pensation filter on/off (brightens dark areas).

Switch dust elimination filter on/off. For use with mirror accessories and dual cam- era model.

Switch worklight on/off. Forward/side view split screen. For use with mirror accessories and dual cameras.

Switch the mirror image on/off.

Change the direction of the worklight (side/forward) when using mirror accesso- ries or dual camera.

Opens the image gallery. Select an image to com- pare with the live image on a split-screen.

Switch the image negative on/off.

Rotate image clockwise (90, 180, 270). Set the white balance.

IR CAMERATOUCH SCREEN ICONS Tap an icon to open its submenu. See the probe user manual for more information.

Rotate image clockwise (90, 180, 270) or view mirror image.

Select color palette (Iron, Rainbow, Gray) or alarm mode (Above alarm, Below alarm).

Tap to open the Measurement submenu for Center Spot, Cold Spot, Hot Spot, and No Measurement modes, explained below.

#NAS100100; r. AC/83794/84876; en-US 4

Page 6

Center spot: Temperature of spot is displayed on upper left.

The coldest (cyan cross-hairs) or hottest (red cross-hairs) spot is targeted in the boxed region of the image. The spot temperature is shown on the upper left side of the display.

Tap and drag the box to move it, use the navigation buttons (up [5], down [6], left [7], right [8]) to re-size it, or pinch/stretch the box with two fingers to narrow or widen it.

No Measurements: Temperature is not measured.

Temperature Scale. Use Auto (A) in normal operation; Use Manual (M) to limit the temperature range, based on the temperature of the targeted spot.

Measurement parameters: Set emissivity, reflected temperature, and temperature units.

ABOVE AND BELOWALARMS (IR CAMERA)

To set an alarm, tap the palette icon and select the Above or the Below alarm.

In Above alarm mode, the camera will apply a red color to all parts of the image with a temperature above the alarm set point. In Below alarm mode, the camera will apply a blue color to all parts of the im- age with a temperature below the alarm set point.

Tap and drag the color bar graph to adjust the set point. CUSTOMER SUPPORT The FLIR support site, address below, is your resource for obtaining firmware upgrade files, latest versions of user manuals, customer service, and other product and accessory information.

https://support.flir.com Three-Year Limited Warranty This product is protected by FLIRs 3-Year Limited Warranty. Visit www.flir.com/testwarranty to read the 3-Year Limited Warranty document.

#NAS100100; r. AC/83794/84876; en-US 5

Page 8

last page

Publ. No.: NAS100100 Release: AC Commit: 83794 Head: 84876 Language: en-US Modified: 2022-03-08 Formatted: 2022-05-06

Website http://www.flir.com Customer support http://support.flir.com Copyright 2022, FLIR Systems, Inc. All rights reserved worldwide. Disclaimer Specifications subject to change without further notice. Models and accessories subject to regional market considerations. License procedures may apply. Products described her

Manualsnet FAQs

If you want to find out how the VS80 Kit Flir works, you can view and download the Flir VS80 Kit Videoscope Quick Start on the Manualsnet website.

Yes, we have the Quick Start for Flir VS80 Kit as well as other Flir manuals. All you need to do is to use our search bar and find the user manual that you are looking for.

The Quick Start should include all the details that are needed to use a Flir VS80 Kit. Full manuals and user guide PDFs can be downloaded from Manualsnet.com.

The best way to navigate the Flir VS80 Kit Videoscope Quick Start is by checking the Table of Contents at the top of the page where available. This allows you to navigate a manual by jumping to the section you are looking for.

This Flir VS80 Kit Videoscope Quick Start consists of sections like Table of Contents, to name a few. For easier navigation, use the Table of Contents in the upper left corner.

You can download Flir VS80 Kit Videoscope Quick Start free of charge simply by clicking the “download” button in the upper right corner of any manuals page. This feature allows you to download any manual in a couple of seconds and is generally in PDF format. You can also save a manual for later by adding it to your saved documents in the user profile.

To be able to print Flir VS80 Kit Videoscope Quick Start, simply download the document to your computer. Once downloaded, open the PDF file and print the Flir VS80 Kit Videoscope Quick Start as you would any other document. This can usually be achieved by clicking on “File” and then “Print” from the menu bar.