Flir Extech RHT20 Datalogger User Manual PDF

1 of 5
1 of 5

Summary of Content for Flir Extech RHT20 Datalogger User Manual PDF

User Manual

Humidity & Temperature Datalogger Model RHT20

Additional User Manual Translations available at www.extech.com 

RHT20-en-GB_V1.5 1/17 2

Introduction Congratulations on your purchase of this Temperature and Humidity datalogger. With this meter, you can monitor and log data over long periods of time and then easily transfer the data to a pc for viewing and evaluation. The LCD display provides current or Max/Min temperature, humidity and time information. This device is shipped fully tested and calibrated and, with proper use, will provide years of reliable service. Please visit our website (www.extech.com) to check for the latest version and translations of this User Manual, Product Updates, Product Registration, and Customer Support.

Description

1 Record LED

2 Alarm LED

3 LCD Display

4 Temperature Humidity display selection

5 MAX/MIN display selection

6 Battery Compartment (rear)

7 Temperature and Humidity sensors

8 USB PC port (bottom)

Display Description

Full battery symbol.

Weak battery symbol. Replace battery when this appears. Battery life is more than 3 months.

DATE: Current date is displayed

TIME: Current time is displayed Time and Date automatically swap every 10 sec.

MAX: Maximum value during a datalogging session is displayed

MIN: Minimum value during a datalogging session is displayed

REC: Recording in progress indicator

FULL: Memory is full indicator

%RH: Humidity value is displayed

C: Celsius temperature units

F: Fahrenheit temperature units

1 2 3 4 5

6

7

8

RHT20-en-GB_V1.5 1/17 3

Operation: The display and front panel buttons provide a means to view the status of the datalogger, observe the current Temperature or Relative Humidity and to view the MAX and MIN values recorded during a recording session. The datalogger setup conditions such as sample rate, temperature units and alarm values are programmed via the provided software. Refer to the software Help File on the disk for those procedures.

1. Press the MAX/MIN button to view the recorded Max and Min values with the time they were recorded. If, while in this mode, no button is pressed for 40 seconds the display will automatically return to the real time display.

2. The Time and Date display will automatically toggle every 10 seconds

3. When downloading the data to the PC, -PC- will be displayed on the LCD. After the download is complete, the datalogger will display the last value recorded, but it will stop recording. The logger needs to be re-set from the software to begin a new recording session.

4. The REC LED will flash at the programmed rate when the unit is datalogging.

5. Alarm function: When the measured value exceeds the programmed upper or lower limit and the LED function is selected in the software, the ALM LED will flash one time per minute.

6. If -LO- is displayed, the temperature and humidity sensors need attention.

7. The datalogger should be placed upright when in use.

8. If used in low temperature, high humidity environment, the datalogger should be placed upright in a dry area to remove any condensation before downloading the data.

9. Battery life can be extended by leaving the datalogger connected to a pc.

10. Disabling the REC and ALM LEDs will extend battery life.

11. The LCD display will stop functioning at very low temperatures and will become active again when the unit is returned to higher temperatures.

NOTE: The logger needs to be re-set from the software to begin a new recording session.

Combination Lock

The logger is supplied with a wall mount case and security combination lock. The lock is shipped with a -0-0-0- code as viewed from the side with the alignment bar. To change the code:

1. Press the release to open the lock (1)

2. Using a pointed object, press IN and HOLD the locking pin on the bottom of the lock (2).

3. Set the new code (3) and release the locking pin 0

0

0

1

3

2

RHT20-en-GB_V1.5 1/17 4

Software Installation 1. Place the CD in the drive and then follow the on-screen installation instruction.

2. After the software is installed, keep the CD in the drive and connect the datalogger to the PC by the USB cable.

3. A USB Driver installation window will pop-up; follow the directions to install the driver.

Software application The Datalogger USB software is a program for collecting data from the DATA LOGGER when it is connected to a PC or notebook computer. The data may be displayed graphically, as Excel or similar programs. The major functions are all listed in the main window.

System Requirements Check the software download page of the extech.com website for the latest version of the PC software and its operating system compatibility.

Minimum Hardware Requirements: PC or NoteBook with Pentium 90MHz or higher, 32 MB RAM; At least 7 MB byte hard disk space available to install HT Datalogger USB software Recommended display resolution 1024 x 768 with High Color (16 bit)

Software Operation The Software operation is described in the HELP file.

Maintenance 

WARNING: To avoid electrical shock, disconnect the meter from any circuit and turn OFF the meter before opening the case. Do not operate with an open case.

Battery Replacement 1. Remove the green protective cover by pushing the bottom of the meter until it slides through

the opening at the top.

2. Remove the two Phillips head screws that secure the battery compartment at the back of the meter.

3. Open the battery compartment and replace the 3.6V lithium battery observing correct polarity.

4. Re-assemble the meter before use.

Safety: Please dispose of batteries responsibly; never dispose of batteries in a fire, batteries may explode or leak. If the meter is not to be used for 60 days or more, remove the battery and store separately.

Never dispose of used batteries or rechargeable batteries in household waste. As consumers, users are legally required to take used batteries to appropriate collection sites, the retail store where the batteries were purchased, or wherever batteries are sold. Disposal: Do not dispose of this instrument in household waste. The user is obligated to take end-of-life devices to a designated collection point for the disposal of electrical and electronic equipment

RHT20-en-GB_V1.5 1/17 5

Specifications Display Multi-function LCD

Measurement ranges 0 to 100% RH -40 to 158F, -40 to 70C

Resolution 0.1, 0.1RH

Maximum data points 16,350 Temperature and 16,350 Humidity values

Sample rate 1s to 24h selectable

Analysis software Check the software download page of the extech.com website for the latest version of the PC software and its operating system compatibility.

Open input indication "LO" appears on the LCD

Low battery indication Empty battery symbol appears on the LCD

Power supply 3.6V Lithium Battery

Battery life 3 months (approximately)

Operating Temperature -40 to 158F, -40 to 70C

Operating Humidity 0 to 100% RH

LCD Operating Temperature -13F to 158F (-25C to 70C)

Dimensions 3.7x1.9x1.2") (94.4x48.9x31.2mm)

Weight 3.2oz (90.7g)

Range Accuracy

Relative Humidity 0 to 20% and 80 to 100% 5.0%

20 to 40% and 60 to 80% 3.5%

40 to 60% 3.0%

Temperature 14 to 104F 1.8F

-13 to 14F and 104 to 158F 3.6F

-40 to -13F 8F typical

-10 to 40C 1C

-25 to -10C and 40 to 70C 2C

-40 to -25C 4C typical

Copyright  20132017 FLIR Systems, Inc.  All rights reserved including the right of reproduction in whole or in part in any form 

ISO

Manualsnet FAQs

If you want to find out how the Extech Flir works, you can view and download the Flir Extech RHT20 Datalogger User Manual on the Manualsnet website.

Yes, we have the User Manual for Flir Extech as well as other Flir manuals. All you need to do is to use our search bar and find the user manual that you are looking for.

The User Manual should include all the details that are needed to use a Flir Extech. Full manuals and user guide PDFs can be downloaded from Manualsnet.com.

The best way to navigate the Flir Extech RHT20 Datalogger User Manual is by checking the Table of Contents at the top of the page where available. This allows you to navigate a manual by jumping to the section you are looking for.

This Flir Extech RHT20 Datalogger User Manual consists of sections like Table of Contents, to name a few. For easier navigation, use the Table of Contents in the upper left corner.

You can download Flir Extech RHT20 Datalogger User Manual free of charge simply by clicking the “download” button in the upper right corner of any manuals page. This feature allows you to download any manual in a couple of seconds and is generally in PDF format. You can also save a manual for later by adding it to your saved documents in the user profile.

To be able to print Flir Extech RHT20 Datalogger User Manual, simply download the document to your computer. Once downloaded, open the PDF file and print the Flir Extech RHT20 Datalogger User Manual as you would any other document. This can usually be achieved by clicking on “File” and then “Print” from the menu bar.