Flir Extech CTH10A Clock User Manual PDF

1 of 5
1 of 5

Summary of Content for Flir Extech CTH10A Clock User Manual PDF

USER MANUAL   

Radio Controlled Clock with  Temperature & Humidity 

Model CTH10A 

EXTECH INSTRUMENTS 

2                                            CTH10AenGB_V2.3   10/15 

Introduction  Thank you for selecting the Extech Model CTH10A Radio Controlled Clock with Hygro Thermometer displays. The CTH10A is a realtime calendar Clock (12/24 hour) that also displays  temperature and relative humidity measurements taken from its internal environmental sensors.  The clock can be set manually or automatically using the RCWWVB time signal. The CTH10A  includes an audible/visible daily alarm function with snooze mode. 

This device is shipped fully tested and calibrated and, with proper use, will provide years of  reliable service. Please visit our website (www.extech.com) to check for the latest version of this  User Guide, Product Updates, Product Registration, and Customer Support. 

Meter Description   

A1: RCWWVB time signal Icon 

A2: Time Display 

A3: Date 

A4: Day of Week 

A5: Indoor Humidity 

A6: Indoor Temperature 

B1: Snooze Button 

B2: MODE/SET Button 

B3: + 12/24 Button 

B4:  C/F   Button 

B5: RESET Button 

B6: AL ON/OFF Button 

C1: Wall Mount Hole 

C2: Battery compartment 

C3: Tilt Stand 

EXTECH INSTRUMENTS 

3                                            CTH10AenGB_V2.3   10/15 

Operation 

Getting Started  Open  the  rear  battery  compartment,  insert  three  (3)  C  type  batteries  observing  correct  polarity and then close and secure the compartment cover. Press the Reset button (using the  tip of a paper clip or pin) in order to initialize the meter.  

Automatic Time Setting  After inserting the batteries and resetting the unit as described above, the clock 

automatically scans for the WWVB time signal and the icon flashes on the LCD. 

 flashes 

Indicating now is receiving  WWVB signal 

turns on 

Indicating signal received  successfully 

 disappears, 

Indicating signal  reception failed 

The clock automatically synchronizes with the WWVB radio signal every day at 2am to  maintain accurate time. If synchronization with the signal fails, the signal icon disappears;  the clock then attempts to synchronize with the WWVB signal at 3, 4, and 5am.  

The clock can be set to scan the time signal manually by holding the   button (B4) for 3 

seconds. Note: If a manual scan is attempted with the signal icon showing, the signal icon will  disappear and the manual scan will have to be attempted again. Each reception takes about  5 minutes. If reception fails, scanning stops and the signal icon disappears; the scan then  repeats on the next full hour (e.g. if a scan failed at 8:20am a scan will be tried again at 9am). 

Stop scanning by holding   button (B4) for 3 seconds. 

Note: Buttons will not function while scanning for the WWVB time signal. 

Manual Time Setting  In the time display mode, hold the MODE button (B2) for 3 seconds to enter the 

Clock/Calendar setting Mode. 

Press + (B3) or  (B4) button to adjust the setting and press the MODE button (B2) to  confirm each setting and move to the next setting. 

The setting sequence is as follows: Hour, Minute, Second, Year, Month/Day sequence,  Month, Day, DST. 

Notes:  

1. All setting modes will automatically exit after 15 seconds of inactivity.  2. Press and hold the plus or minus button for faster scrolling of digits while editing.  3. For Time Zones: The default setting is zone P. Hold + (B2) button for 3 seconds to change 

to another zone P M C or E Pacific, Mountain, Central, and Eastern.  4. DST: When the DST function is activated (Daylight Saving Mode) DST will be shown on the 

LCD. Set DST as described in the Manual Time Setting section above.   

EXTECH INSTRUMENTS 

4                                            CTH10AenGB_V2.3   10/15 

Daily Alarm Setting 

Press MODE button (B2) to view the Alarm Time, AL is shown on the display. 

When  viewing  the  Alarm  Time,  hold  MODE  button  (B2)  for  3  seconds  to  enter  the 

Alarm Time setting mode. Press + (B3) or  (B4) button to adjust the alarm time. Press 

the MODE button (B2) to confirm the setting and move to the next setting. 

Press AL ON/OFF Button (B6) to activate or deactivate the alarm. If the alarm is on, the 

alarm icon "   " appears on the display. 

Snooze Alarm 

Press  the  SNOOZE  (B1) button when  the  alarm  tone  sounds.  The  alarm  snoozes  for 

approx. 5 minutes, after which time it alerts again.   flashes on the LCD during the 

snooze time. This process can be repeated 7 times.  

Except  for  the SNOOZE button, any button can be pressed  to stop  the snooze alarm. 

Otherwise, the alarm signal sounds for 2 minutes, then stops automatically. 

12/24 Hour Display Mode  Press the 12/24 (B3) button to select the 12 or 24 hour mode.  

Thermometer and Relative Humidity Displays 

The CTH10A includes internal temperature and relative humidity sensors. Temperature 

and relative humidity measurements are displayed on the lower right side of the clock.

Press the C/F (B4) button to select C: Celsius or F: Fahrenheit units.

If the temperature exceeds the measurable range, LL.L (beyond the minimum 

temperature) or HH.H (beyond the maximum temperature) will be shown on the LCD.

Important Notes   

The clock loses time information when the batteries are removed. 

Do not expose the Clock to direct sunlight, extreme temperatures, or high humidity  

Never clean the device using abrasive or corrosive materials or products. Use a damp 

cloth to wipe the housing clean as necessary. 

EXTECH INSTRUMENTS 

5                                            CTH10AenGB_V2.3   10/15 

Battery Replacement  When  the Clock no  longer displays digits and  text please  replace  the batteries. Open  the  rear  battery compartment, insert three (3) C type batteries observing correct polarity and then close  and secure the compartment cover. Press the Reset button (using the tip of a paper clip or pin)  in order to initialize the meter.  

Never dispose of used batteries or rechargeable batteries in household waste. 

As consumers, users are legally required to take used batteries to appropriate collection sites,  the retail store where the batteries were purchased, or wherever batteries are sold. 

Disposal: Do not dispose of  this  instrument  in household waste. The user  is obligated  to  take endoflife  devices to a designated collection point for the disposal of electrical and electronic equipment.  

Specifications 

Display       Extralarge multifunction LCD 

Calendar Clock      Realtime calendar clock (up to year 2069) 

Time signal detector  RCWWVB radio signal automatically sets the time (clock  time may also be manually set) 

Temperature Measurement range  0~50 oC (32~122oF) 

Storage Temperature    20~60 oC (4~140oF) 

Temperature Resolution    0.1 oC or oF 

Temperature Accuracy    1.5C (3F): 5C to 0C (23F to 32F) 

        1C (2F): 1C to 30C (33F to 86F) 

        3F (1.5C): 31C to 50C (87F to 122F) 

Overrange temp. indication  HH.H display 

Underrange temp. indication  LL.L display 

R.H. Measurement range    20~99% Relative Humidity 

R.H Accuracy      20% to 40% RH: 8% RH (@25C) 

        41% to 70% RH: 6% RH (@25C) 

        71% to 90% RH: 8% RH (@25C)     

Power supply      Three (3) C type batteries 

Dimensions      29 x 43 x 3.8 cm (11.4 x 17 x 1.5 in.) 

Weight       1.25 kg (2.75 lbs.) 

Copyright  2015 FLIR Systems, Inc.  All rights reserved including the right of rep

Manualsnet FAQs

If you want to find out how the Extech Flir works, you can view and download the Flir Extech CTH10A Clock User Manual on the Manualsnet website.

Yes, we have the User Manual for Flir Extech as well as other Flir manuals. All you need to do is to use our search bar and find the user manual that you are looking for.

The User Manual should include all the details that are needed to use a Flir Extech. Full manuals and user guide PDFs can be downloaded from Manualsnet.com.

The best way to navigate the Flir Extech CTH10A Clock User Manual is by checking the Table of Contents at the top of the page where available. This allows you to navigate a manual by jumping to the section you are looking for.

This Flir Extech CTH10A Clock User Manual consists of sections like Table of Contents, to name a few. For easier navigation, use the Table of Contents in the upper left corner.

You can download Flir Extech CTH10A Clock User Manual free of charge simply by clicking the “download” button in the upper right corner of any manuals page. This feature allows you to download any manual in a couple of seconds and is generally in PDF format. You can also save a manual for later by adding it to your saved documents in the user profile.

To be able to print Flir Extech CTH10A Clock User Manual, simply download the document to your computer. Once downloaded, open the PDF file and print the Flir Extech CTH10A Clock User Manual as you would any other document. This can usually be achieved by clicking on “File” and then “Print” from the menu bar.