Page 3
3
Consumer Information
WARNING
Prevent Entanglement Injury Keep mobile out of babys reach... Remove mobile portion of product from crib or playpen
when baby begins to push up on hands and knees... This product may not attach to all crib designs... Do not add
additional strings or straps to attach to crib or playpen... Use ONLY attached to a crib or playpen...
IMPORTANT! Always attach with all provided fasteners tightly to a crib or playpen according to the instructions... Do not add additional strings or straps to attach to a crib... Check frequently... Please keep this instruction sheet for future reference, as it contains important information... Requires three "C" (LR14) alkaline batteries for mobile/base operation (batteries
not included)... Adult assembly is required... Tool required for assembly: Phillips screwdriver (not included)... The mobile portion of this product may be used from birth until 5 months... The base portion of this product may be used from birth until 24 months... A crib mobile is intended for visual stimulation and is not to be grasped by a child... Care
Wipe this toy with a clean cloth dampened with a mild soap and water solution... Do not immerse this toy... The soft toys are surface washable...
This toy has no consumer serviceable parts... Do not take this toy apart... If this product begins to operate erratically, you may need to reset the electronics...
Slide the power/volume switch off and then back on...
ICES-003
This Class B digital apparatus complies with Canadian ICES-003... Operation is subject to the following two conditions: (1) this device may not cause harmful interference and (2) this device must accept any interference received, including interference that may cause undesired operation...
NMB-003
Cet appareil numrique de la classe B est conforme la norme NMB-003 du Canada... Lutilisation de ce dispositif est autorise seulement aux conditions suivantes: (1) il ne doit pas produire de brouillage et (2) lutilisateur du dispositif doit tre prt accepter tout brouillage radiolectrique reu, mme si ce brouillage est susceptible de compromettre le fonctionnement du dispositif...
Page 4
4
Parts
Note: All of the screws used to assemble this toy are attached to the product... Follow these instructions carefully to fully secure the screws... Tighten and loosen all
screws with a Phillips screwdriver... Do not over-tighten the screws...
Mobile Arm Mobile Cap
3 Thick Spokes3 Th k Sp
3 Toys
3 Thin Spokes
Base
Page 5
5
1,5V x 3 "C" (LR14)
Loosen the screws in the battery compartment door with a Phillips screwdriver... Remove the battery compartment door...
Insert three "C" (LR14) alkaline batteries... Hint: We recommend using alkaline batteries for longer battery life... Replace the battery compartment door and tighten the screws... When sounds or motion become faint or stop, its time for an adult to change
the batteries...
Battery Installation
In exceptional circumstances, batteries may leak fluids that can cause a chemical burn injury or ruin your product... To avoid battery leakage:
Do not mix old and new batteries or batteries of different types: alkaline, standard (carbon-zinc) or rechargeable (nickel-cadmium)...
Insert batteries as indicated inside the battery compartment... Remove batteries during long periods of non-use... Always remove exhausted batteries
from the product... Dispose of batteries safely... Do not dispose of this product in a fire... The batteries inside may explode or leak...
Never short-circuit the battery terminals... Use only batteries of the same or equivalent type, as recommended... Do not charge non-rechargeable batteries... Remove rechargeable batteries from the product before charging... If removable, rechargeable batteries are used, they are only to be charged under adult supervision...
Battery Safety Information
Protect the environment by not disposing of this product with household waste (2002/96/EC)... Check your local authority for recycling advice and facilities (Europe only)...
Page 6
6
Fit the thin mobile spokes onto the pegs on the mobile arm... Hint: The spokes are designed to fit on alternating pegs one way... If a thin spoke does not seem to fit, try the next peg...
11
Assembly Thin Spoke
Thin Spoke
Thin Spoke
12 Fit the thick mobile spokes onto the remaining pegs on the mobile arm...
Thick Spoke
Thick Spoke
Thick Spoke
Page 7
7
14 Fit the T-end of the strap on each mobile toy through the slot in each thick spoke... Pull down on each toy to be sure it is secure...
Assembly
Fit the mobile cap over the ends of the thin and thick spokes and onto the top of the mobile arm...
Tighten the screw in the mobile cap...
13
Mobile Cap
Toy
Toy
Toy
Page 8
8
Base
15
First, press the button on the base next to the socket A and then slide the socket door open B ...
Fit the mobile arm into the socket in the base and tighten both screws...
Assembly
A
B
Page 9
9
Crib Attachment
11
IMPORTANT! If you are attaching this toy to a crib side rail that can be lowered and raised, make sure the crib side rail is in the raised (locked) position whenever a child is in the crib... Position the base inside the crib... Wrap the attachment strap around the top of the crib rail... Slide the end of the attachment strap under the tabs on the back of the base... Fasten the attachment strap slot to the peg on the back of the base... Note: This toy should be snug against the crib rail and spindles... Use the strap slot that provides the tightest fit...
Attachment StrapAttachment Strap
PegPeg
Crib Rail
IMPORTANT! Always attach all provided fasteners (strings, straps, clamps, etc... )
tightly to a crib or playpen according to the instructions... Do not add additional
strings or straps to attach to a crib... Check frequently...
Page 10
10
Crib Attachment
Tie the toys strings to a crib spindle... Note: It is better to tie the strings in a knot than a bow, since a bow may be easily untied...
13
Make sure the distance between the bottom of the product and the crib mattress is at least 7 inches (18cm)...
If the distance is less than 7 inches (18cm): readjust the attachment strap to lift the product; or lower the crib mattress...
12 At Least 7 Inches (18cm)At Least 7 Inches (18cm)
MattressMattress
Bottom of BaseBottom of Base
Page 11
11
Use
Spin the roller or press the button to start the music or mobile...
Power/Volume SwitchPower/Volume Switch
Slide the switch to ON with low volume or ON with high volume ... When finished using the product, slide the switch OFF ...
Music SwitchMusic Switch
Slide the switch to select: Soothing Active
Mobile SwitchMobile Switch
Slide the switch to select a mode: Music and Motion Music only
PressPress
SpinSpin
Page 12
12
Remove the mobile and use as a music box!
Convert to Music Box
Loosen both screws in the arm near the base... Lift and remove the arm... Close the socket door on top of the base... Hint: The socket door must be completely closed for use as a music box... Store the mobile in a safe place for future use...
The toys can be removed from the mobile and inserted into the slots on the base... Fit the T-end of the strap on each toy through the slots in the base... Pull down on each toy to be sure it is secure...
en
fr
sp