Fisher Price Mattel Dreamsicle Collection 3-in-1 High P9043 Chair Instruction Manual PDF

Pages 16
Year 2009
Language(s)
English en
1 of 16
1 of 16

Summary of Content for Fisher Price Mattel Dreamsicle Collection 3-in-1 High P9043 Chair Instruction Manual PDF

Page 3

3

Note: Tighten and loosen all screws with a Phillips screwdriver... Do not over-tighten the screws...

FASTENERS SHOWN ACTUAL SIZE

#8 x " Screw with Plastic Retainer 4 #8 x " Screw 6

Seat Support

Assembled Parts

Front Base Rear Base

Footrest

2 Frames

IMPORTANT! Please remove all parts from the package and identify them before assembly...

Seat Back Pad 2 Brackets

(Left and Right)

Seat with Restraint

Seat Pad

Seat Back with Restraint

Tray

Hint: Do not remove the plastic inserts inside the tubes of the front base...

Hint: Do not remove the plastic insert inside the tube in each frame...

Page 4

4

Fit a #8 x " screw with retainer into the rear base and tighten... Repeat steps 1 and 2 to assemble the other frame to the rear base...

With the Fisher-Price logo facing out, fit the tapered frame tube into the rear base...

IMPORTANT! Before assembly and each use, inspect this product for damaged hardware, loose joints, missing parts or sharp edges... DO NOT use if any parts are missing or broken... Contact Fisher-Price for replacement parts and instructions if needed... Never substitute parts...

Rear Base

1

2

Tapered Frame Tube

Lay the frame assembly down with long frame tubes up... Position the seat support with the frame latches down... Slide the seat support onto the frame tubes... Hint: Push the seat support all the way to the top of the assembly... You will hear several "clicks"...

3

Frame Latches

Frame Assembly

CAUTION

This package contains small parts in its unassembled state...

Adult assembly is required...

Frame TubesSeat Support

Assembly

Page 5

5

Lift the frame assembly upright... Fit the footrest onto the seat support, as shown...

6

Fit the front base into the frame tubes...

4

Insert two #8 x " screws with retainers into the holes in each frame tube and tighten...

Hint: If you cannot insert the screws into the frame tubes, you have assembled the front base backwards... Remove it, turn it around and re-assemble it to the frame tubes...

5

Front Base

Footrest

Seat Support

Insert two #8 x " screws into the holes on each side of the footrest and tighten...

7

Assembly

Page 6

6

Assembly

8

Turn the frame so that the footrest faces away from you... First fit the left bracket (labeled 1) onto the seat support tube

closest to you A ... Then, slide the left bracket completely onto the seat support B ... Hint: The brackets are designed to fit each side of the seat support one way... If the bracket does not seem to fit, try the other one...

9

Insert a #8 x " screw through the left bracket and into the seat support and tighten...

A

A

B

B

Seat Support

#8 x " Screw

Seat Support Tube

Seat Support Tube

Seat Support Right Bracket

Left Bracket

10

First fit the right bracket (labeled 2) onto the seat support tube closest to you A ...

Then, slide the right bracket completely onto the seat support B ...

11

Insert a #8 x " screw through the right bracket and into the seat support and tighten...

#8 x " Screw

Page 7

7

Unbuckle the lower restraint...

13

Pull the lower restraint ends through the slots in the seat pad... Fit the elastic loops on the seat pad down through the slots in

the seat... Turn the seat upside down... Pull the elastic straps through the slots in the seat and fit the

elastic straps to the pegs...

Pull the shoulder restraint ends through the slots in the seat pad... Fit the straps on the back of the seat back pad into the slots in the

seat back...

14

15

Seat Pad

Elastic Straps

Pegs

Assembly

At an angle, fit the tabs on the seat back into the slots in the seat A ...

Push the seat back to snap in place B ... IMPORTANT! Pull on the seat back to be sure it is secure to the seat bottom...

12

Slot

Slot

Tab Tab

B

A A

Page 8

8

To adjust the restraint height for baby, push to remove the shoulder restraints from the seat back...

17

Press to fasten the straps to secure the seat back pad...

16

Straps

Larger Baby

Insert the ends of the shoulder belts through the upper slots in the pad and seat back...

19

Lower Shoulder Belt Slots

Smaller Baby

Insert the ends of the shoulder belts through the lower slots in the pad and seat back...

18

Upper Shoulder Belt Slots

Assembly

Page 9

9

Securing Your Child

WARNING

Prevent serious injury or death from falls or sliding out:

Only use for a child capable of sitting upright unassisted...

NEVER leave child unattended... High Chair Use:

ALWAYS secure child with restraint belts adjusted to fi t your child snugly... The tray is not designed to hold child in the product...

When attached to adult chair:

Use restraint belts until child is able to get in and out of the product without help (about 21/2 years old)...

Seat Assembly

Place the seat assembly on the frame assembly and push to lock in place... You should hear a "click"...

Note: The seat assembly will only fit on the frame assembly if the chair attachment strap door is closed... If the seat assembly does not lock onto the frame assembly, check to make sure the sliding door under the seat is completely closed...

21

Frame Assembly

Assembly

Fit the "T" end of each shoulder belt through the slots in the lower restraint...

20 Slots

Page 10

10

Securing Your Child

Tighten each waist belt/shoulder belt so that the restraint system is snug against your child... Please refer to the next section for instructions to tighten the waist belts/shoulder belts...

2

To loosen the waist belts: Feed the free end of the waist belt up through the buckle to form a loop A ... Enlarge the loop by pulling on the end of the loop toward the buckle...

Pull the anchored end of the waist belt to shorten the free end of the waist belt B ...

To loosen the shoulder belts: Lift the adjuster C ... Note: After adjusting the restraint system to fit your child, make sure you pull on it to be sure it is securely fastened...

LOOSEN4

To tighten the waist belts: Feed the anchored end of the waist belt up through the buckle to form a loop A ... Pull the free end of the waist belt B ...

To tighten the shoulder belts: Hold the adjuster and pull the shoulder belt down C ...

TIGHTEN3

Adjuster Adjuster

Place your child in the seat... Position the crotch belt between your childs legs...

Fasten both waist/shoulder belts to each side of the crotch belt... Make sure you hear a "click" on both sides...

Check to be sure the restraint system is securely attached by pulling it away from your child... The restraint system should remain attached...

1

Crotch Belt

Waist/Shoulder Belt

Waist/Shoulder Belt

Page 11

11

Using the Tray

Fit the tray onto the seat armrests... Push down until the tray "snaps" into place...

Hint: Before use, thoroughly wash all parts (the tray) that may contact food... The tray is not dishwasher or microwave safe...

1

Tray

Armrest

While pushing the release bar on the front of the tray, adjust the tray forward or backward...

2

Release Bar

WARNING

Prevent serious injury or death from falls or sliding out: ALWAYS secure child with restraint belts adjusted to fi t your child snugly... The tray is not designed to hold child in the product...

While pushing the release bar on the front of the tray, pull the tray away from the armrests...

3

Release Bar

Page 12

12

Adjusting the Seat Attaching To An Adult Chair

WARNING

Prevent serious injury or death from falls or sliding out:

Only use for a child capable of sitting upright unassisted...

NEVER leave child unattended... Use restraint belts until child is able to

get in and out of the product without help (about 21/2 years old)...

NEVER use in motor vehicles... ALWAYS secure the product on a chair

using bottom and back attach-ment straps... NEVER use on a stool or bench that does not have a seat back...

To prevent falls:

NEVER release the seat with child in product...

NEVER carry child in the seat...

To adjust the seat height:

Press the levers on both seat height adjusters and lift or lower the seat to any of five different heights...

Make sure both sides of the seat are adjusted to the same height...

Push the seat to be sure the seat is locked in place...

PRESS

Seat Height Adjuster

Page 13

13

While sliding the switch A pull the latch towards you B ...

Attaching To An Adult Chair

Lift the seat off the base...

2

Match the buckle on each strap to the matching buckle icon near each slot in the seat... Feed each strap through the matching slot on the seat...

4 Openings

Openings

Turn the seat over... Slide the door open and pull out the chair attachment straps...

3 Door

A B

1

Latch

Chair Attachment Straps

Page 14

14

Attaching To An Adult Chair

Wrap the back straps around the back of the chair D ... Buckle the straps E ... Make sure you hear a "click"... Pull the free end of each strap to tighten on the chair F ...

Pull up on the seat to be sure it is secure to the chair...

6

Turn the seat over and place the seat on a chair... Wrap the bottom straps around the bottom of the chair A ...

Buckle the straps B ... Make sure you hear a "click"... Pull the free end of each strap to tighten on the chair C ...

5

Remove the Seat Back and Shoulder Belts

Pull the shoulder belts out of the waist restraint buckle slots...

1

Pull the tab on the seat back... Lift to remove the seat back from the seat...

2

LIFT

PULL TAB

Page 15

15

Attaching the Seat To the Frame

Door

Chair Attachment Straps

Turn the seat over and open the door... Carefully fit the chair attachment straps into the compartment...

1

IMPORTANT! Close the door completely... If you do not close the door, the seat will not fit on the high chair base...

2

Fit the seat onto the high chair frame... Push to "snap" into place... Pull up on the seat to be sure it is secure to the high chair frame...

3

Storage

The bib, toy, tray, pad, seat, seat back and restraint belts may be wiped clean using a mild cleaning solution and damp cloth... Do not use bleach... Do not use harsh or abrasive cleansers... Rinse clean with water to remove residue...

To remove the pad:

Push to remove the shoulder belts, waist belts and crotch belt from the seat and pads...

Unfasten the straps on the seat back... Remove the pads from the seat... To replace the pad and restraint belts, refer to the assembly

instructions in this manual... IMPORTANT! Be sure to replace the restraint system... Never use this product without the restraint system when used as a high chair or when attached to an adult chair (until your child cannot get in and out of the product without help)...

Care

Pull the frame release latches forward and push the rear legs toward the front legs...

Page 16

CANADA

Mattel Canada Inc... , 6155 Freemont Blvd... , Mississauga, Ontario L5R 3W2...

Fisher-Price, Inc... , a subsidiary of Mattel, Inc... , East Aurora, New York 14052, U... S... A... 2009 Mattel, Inc... All Rights Reserved... and designate U... S... trademarks of Mattel, Inc...

PRINTED IN MEXICO P9043pr-0921

Manualsnet FAQs

If you want to find out how the Mattel Fisher Price works, you can view and download the Fisher Price Mattel Dreamsicle Collection 3-in-1 High P9043 Chair Instruction Manual on the Manualsnet website.

Yes, we have the Instruction Manual for Fisher Price Mattel as well as other Fisher Price manuals. All you need to do is to use our search bar and find the user manual that you are looking for.

The Instruction Manual should include all the details that are needed to use a Fisher Price Mattel. Full manuals and user guide PDFs can be downloaded from Manualsnet.com.

The best way to navigate the Fisher Price Mattel Dreamsicle Collection 3-in-1 High P9043 Chair Instruction Manual is by checking the Table of Contents at the top of the page where available. This allows you to navigate a manual by jumping to the section you are looking for.

This Fisher Price Mattel Dreamsicle Collection 3-in-1 High P9043 Chair Instruction Manual consists of sections like Table of Contents, to name a few. For easier navigation, use the Table of Contents in the upper left corner.

You can download Fisher Price Mattel Dreamsicle Collection 3-in-1 High P9043 Chair Instruction Manual free of charge simply by clicking the “download” button in the upper right corner of any manuals page. This feature allows you to download any manual in a couple of seconds and is generally in PDF format. You can also save a manual for later by adding it to your saved documents in the user profile.

To be able to print Fisher Price Mattel Dreamsicle Collection 3-in-1 High P9043 Chair Instruction Manual, simply download the document to your computer. Once downloaded, open the PDF file and print the Fisher Price Mattel Dreamsicle Collection 3-in-1 High P9043 Chair Instruction Manual as you would any other document. This can usually be achieved by clicking on “File” and then “Print” from the menu bar.