Fisher Price Mattel Cozy Fit Infant-to-Toddler High B2111 Chair Instruction Manual PDF

1 of 16
1 of 16

Summary of Content for Fisher Price Mattel Cozy Fit Infant-to-Toddler High B2111 Chair Instruction Manual PDF

Model Numbers: 79666, B2109, B2110, B2111

Please keep this instruction sheet for future reference, as it contains important information.

Adult assembly is required.

Tools needed for assembly: Phillips Screwdriver (not included).

Product features and decorations may vary from the photo above.

Discover whats possiblewww.fisher-price.com

Infant to Toddler High Chair

2

Occasionally a consumer may experience a problem with one of our products. If this should happen, please call us toll-free, rather than return this product to the store. Usually, we can solve the problem over the telephone or send you replacement parts. Please call Fisher-Price Consumer Relations, toll-free at 1-800-432-5437, 8 AM- 6 PM EST Monday through Friday. Hearing-impaired consumers using TTY/TDD equipment, please call 1-800-382-7470.

Or, write to: Fisher-Price

Consumer Relations 636 Girard Avenue

East Aurora, New York 14052

For other countries, outside the United States:

Canada: call 1-800-567-7724, or write to: Mattel Canada Inc., 6155 Freemont Blvd., Mississauga, Ontario L5R 3W2.

Great Britain: telephone 01628 500302.

Australia: Mattel Australia Pty. Ltd., 658 Church Street, Locked Bag #870, Richmond, Victoria 3121 Australia. Consumer Advisory Service 1300 135 312.

New Zealand: 16-18 William Pickering Drive, Albany 1331, Auckland.

Consumer InformationWarning

Prevent serious injury or death from falls or sliding out. The child should be secured in

the high chair at all times by the restraining system, either in the recline, semi-recline or upright position. The restraint belts must be adjusted to fit your child snugly. The tray is not designed to hold the child in the chair.

Always keep child in view while in the high chair.

Never leave child unattended. It is recommended that the high

chair be used in the upright position only by children capable of sitting upright unassisted.

WARNING

3

Parts

Rear Support

2 Retainers

Front Support

4 Legs

Seat with Restraint System

Restraint Post

Footrest

2 Bases

2 Armrests

Pad

Tray

Seat Tube

ALL SHOWN ACTUAL SIZE

2 Leg Caps

#8 x 3/4" Screw - 7

#8 x 15/8" Screw - 2

#10 Lock Nut - 4

#8 Lock Nut - 2

#10 x 21/8" Screw - 4

IMPORTANT! All consumer assembled screws must be fully tightened for

proper assembly of this product.

Assembly

4

IMPORTANT! Before each use or assembly, inspect this product for damaged hardware, loose joints, missing parts or sharp edges. DO NOT use if any parts are missing or broken. Contact Fisher-Price for replacement parts and instructions if needed. Never substitute parts.

Legs

NotchNotch

Base Tubes

Numbers

1

Fit a leg cap into the openings of two legs, as shown. Push down on the leg cap to be sure it is secure, and there

is no gap between the top of the legs and the leg cap. Repeat this procedure to attach the other leg cap to the

other two legs.

Legs

Leg Cap

2

Leg Cap

Track

Armrest

3 Position a base so that the notches face you. Position two legs so that the numbers face you. Fit a leg onto each base tube. Twist and push each leg until it "snaps" into each base tube. Repeat this procedure to assemble the remaining two legs to

the other base.

Position an armrest so that the track is facing out. Fit the armrest onto a leg cap, as shown. Repeat this procedure to attach the other armrest to the

other leg cap.

This product contains small parts in its unassembled state. Adult

assembly is required.

CAUTION

Assembly

5

Turn the leg assembly, as shown, so that the armrests point toward you.

Position the front support so that the arrows are pointing toward you.

Fit the ends of the front support up between the inside of the armrests and the front legs.

Armrest

Front Leg

Front Support Arrows

5

Insert a #10 x 21/8" screw through the outside of an armrest, a rear leg and then out through the inside of the armrest.

Fit a #10 lock nut into the hexagonal opening on the inside of the armrest. Make sure the rounded side is facing out.

Fully tighten the screw with a Phillips screwdriver. When properly tightened, the end of the screw will be visible, as shown above.

Repeat this procedure to secure the other armrest with a #10 x 21/8" screw and a #10 lock nut.

Armrest

Rear Legs

#10 Lock Nut

#10 x 21/8" Screw - 2

Shown Actual Size

#10 Lock Nut - 2 Rounded Side

Shown Actual Size

End of Screw Visible

Lock Nut

4

Assembly

6

While holding the front support in place, insert #10 x 21/8" screw through the outside of an armrest, front leg, front sup- port and then out through the inside of the armrest.

Fit a #10 lock nut into the hexagonal opening on the inside of the armrest. Make sure the rounded side is facing out.

Fully tighten the screw with a Phillips screwdriver. When properly tightened, the end of the screw will be visible, as shown above.

Repeat this procedure to fasten the front support to the other armrest with a #10 x 21/8" screw and #10 lock nut.

#10 Lock Nuts

Front Leg

Front Support Front

Leg

6

7

Position the seat face down on a flat surface. Insert the seat tube through the a rectangular slot, the two

circular slots in the recline bar and then out through the other rectangular slot.

Circular Slots Seat Tube

Rectangular Slots

Recline Bar

8

Align the arrows on the seat tube with the arrows on the recline bar.

Turn Seat Tube

to Align Arrows

Recline Bar

#10 x 21/8" Screw - 2

Shown Actual Size

#10 Lock Nut - 2 Rounded Side

Arrows on Seat Tube

Arrows on Recline Bar

Shown Actual Size

End of Screw Visible

Lock Nut

Assembly

7

Face the back of the seat assembly. First, fit the left end of the seat tube into the lowest opening

in the left armrest. Then, fit the right end of the seat tube through the notch

in the right armrest and then into the lowest opening in the armrest.

Left End of Seat Tube

Right End of Seat

Tube

Notch

Lowest Openings

10 Back View

At an angle, fit the seat between the armrests. Now, fit the grooves in the seat tabs to the front support.

Seat

Front Support

Grooves

ArmrestArmrest

9

Assembly

8

Align the arrows on the seat tube with the arrows on the recline bar.

Insert a #8 x 3/4" screw through the hole in the recline bar and into the seat tube. Fully tighten the screw with a Phillips screwdriver.

Seat Tube

Hole

11

Squeeze the seat recline and push the seat back forward to the most upright position.

12

Shown Actual Size

#8 x 3/4" Screw

Upright

Squeeze

Seat Recline

Arrows on Seat Tube

Arrows on Recline Bar

Assembly

9

Insert four #8 x 3/4" screws through the footrest and into the seat tabs.

Fully tighten the screws with a Phillips screwdriver.

14

Shown Actual Size

#8 x 3/4" Screw - 4

Fit the footrest over the front support and onto the long and short tabs on the seat.

13

Footrest Front Support

Short Tab Short Tab

Long Tabs

Assembly

10

Position the assembly upright. At an angle, insert the large tab on the restraint post into the

slot between the seat and the footrest. Then, push to snap the restraint post into the large opening

in the footrest.

15

Restraint Post

Position the assembly face down. Insert a #8 x 3/4" screw through each

end of the seat and into the footrest.

Fully tighten the screws with a Phillips screwdriver.

16

Shown Actual Size

#8 x 3/4" Screw - 2

Face the back of the assembly. Position the rear support so that it bends upright. Align the screw holes in the rear support with the screw holes

in the rear legs. Now, place a retainer over each end of the rear support. Insert a #8 x 15/8" screw through the outside of each rear leg,

the rear support and into the retainer. Fit a #8 lock nut into the hexagonal opening in the retainers.

Make sure the rounded side is facing out. Fully tighten the screws with a Phillips screwdriver. When

properly tightened, the end of the screw will be visible, as shown above.

Rear Support

Retainers

Seat

Footrest

#8 x 15/8" Screw - 2

Shown Actual Size

17

#8 Lock Nut - 2 Rounded Side

Shown Actual Size

End of Screw Visible

Lock Nut

Back View

Assembly

11

Place the pad onto the seat Insert the two top elastic straps through the slots labeled 1

in the head supports.

Seat Pad

Elastic Straps

18

Lift the head supports to locate the large hole in the seat back labeled 2.

Insert the elastic straps through the large holes labeled 2.

Elastic Straps 19

Head Support Head Support

From behind the seat, hook the elastic straps over the tabs labeled 3.

20

. From the front of the seat, fit the top pocket on the back of the pad over the top of the seat.

From the back of the seat, fit the top edges of the pad around the head support levers.

Press the center of the pad to fasten it to the seat.

21

Tabs

Elastic Straps

Top of Pad

Head Support Levers

Back View

Back View

Press

Assembly

12

Lift the bottom of the pad. Fit the elastic straps through

the in slots the seat bottom. From the back of the seat, fit the elastic straps onto the tabs,

as shown.

22

Elastic Straps

Tabs

SlotSlot

Fit the waist belts through the two upper slots in the pad. Fit the crotch belt through the lower slot in the pad.

Crotch Belt

Lower Slot

Waist Belt

Waist Belt

23

Upper Slots

From behind the seat, hook the elastic straps onto the posts, as shown.

Posts

Fit the elastic straps on the edge of the pad through the slots in the footrest.

Slots

Elastic Straps

25

24

Back View

Back View

13

Securing Your Child

Place your child in the seat. Position the crotch belt between your childs legs.

Fasten both waist belts to each side of the crotch belt. Make sure you hear a "click" on both sides.

Check to be sure the restraint system is securely attached by pulling it away from your child. The restraint system should remain attached.

Crotch Belt

Waist Belts

IMPORTANT! Before each use, inspect this product for damaged hardware, loose joints, missing parts or sharp edges. DO NOT use if any parts are missing or broken. Contact Fisher-Price for replacement parts and instructions if needed. Never substitute parts.

Prevent serious injury or death from falls or sliding out. The child should be secured in the high chair at all times by the restraining system. The restraint belts must be adjusted to fit your child snugly. The tray is not designed to hold the child in the chair.

WARNING

1

To tighten the waist belts: Feed the anchored end of the waist belt up through the

buckle to form a loop .A

Pull the free end of the waist belt . Repeat this procedure to tighten the other waist belt.

B

To loosen the waist belts: Feed the free end of the waist belt up through the buckle to

form a loop . Enlarge the loop by pulling on the end of the loop toward

the buckle. Pull the anchored end of the waist belt to shorten the free

end of the waist belt . Repeat this procedure to loosen the other waist belt.

B

A

Buckle

Buckle

2

3

14

Using the Tray

Fit the tray onto the armrests, as shown. Push down until the tray snaps into place.

Test to be sure the tray is secure on the armrests. Push the tray back and forth. It should not move.

ArmrestArmrest

Prevent serious injury or death from falls or sliding out. The child should be secured in the high chair at all times by the restraining system. The restraint belts must be adjusted to fit your child snugly. The tray is not designed to hold the child in the chair.

WARNING

1

Hint: Before use, thoroughly wash the tray.

While pushing the button on the front of the tray, adjust the tray forward or backward. Make sure it locks into position.

To remove the tray, push the button on the front of the tray and slide it forward and off the armrests.

Slide Forward

to Remove

Adjust Forward or Backward

Push

2

To adjust the seat height: Press the height lever on the front base and lift or lower the

seat to the desired height. Make sure both front legs are adjusted to the same height. Press the height lever on the rear base and lift or lower the

seat to the same height as the front legs. Make sure both rear legs are adjusted to the same height. Push the seat bottom to be sure all four legs are locked

in place.

IMPORTANT! Make sure the number that shows in each notch in the front an back bases are the same for all four legs.

Prevent serious injury or death from falls or sliding out. It is recommended that the high chair be used in the upright position only by children capable of sitting upright unassisted.

WARNING

Adjusting the Seat Height

Notch

Height Position Number

Push Height Lever

Hint: Adjust the seat height to any of three positions 1, 2 or 3.

Adjusting the Seat Angle

To adjust the seat angle: Squeeze the seat recline and

push the seat back forward or pull it backwards to the desired position.

Push the seat back to be sure it is latched in position.

IMPORTANT! When the seat is in the recline positions, be sure the tray is secure on the armrests. Push the tray back and forth. It should not move.

Recline

Upright

Squeeze

Seat Recline

Hint: Adjust the seat angle in any of four positions: Upright, Semi-Upright, Semi-Recline or Recline.

15

The pad is machine washable. Wash the pad separately in cold water on the gentle cycle. Do not use bleach. Tumble dry separately on low heat and remove promptly.

The frame and tray may be wiped clean using a mild cleaning solution and a damp cloth. Do not immerse the tray.

To remove the pad: Remove the six elastic loops from the pegs on the back of the

seat and underside of the footrest. Remove the pad upper pocket from the seat back. Feed the waist straps through the slots in the pad and the seat. Feed the waist straps through the slot in the pad and the seat. Remove the pad from the seat.

To replace the pad, refer to Assembly steps 18-25. IMPORTANT! Never use this product without the restraint system.

Care

Fisher-Price, Inc., a subsidiary of Mattel, Inc., East Aurora, NY 14052 U.S.A. Printed in Mexico 2002 Mattel, Inc. All Rights Reserved. and designate U.S. trademarks of Mattel, Inc. 79666pr-0920

Using the Head Supports

Headrest Lever

Headrest Lever

Press the head support levers to raise supports.

Press to Raise

Supports

Press to Raise

Supports

Headrest Lever

Headrest Lever

Lift the head support levers to lower supports.

Lift to Lower

Supports

Lift to

Manualsnet FAQs

If you want to find out how the Mattel Fisher Price works, you can view and download the Fisher Price Mattel Cozy Fit Infant-to-Toddler High B2111 Chair Instruction Manual on the Manualsnet website.

Yes, we have the Instruction Manual for Fisher Price Mattel as well as other Fisher Price manuals. All you need to do is to use our search bar and find the user manual that you are looking for.

The Instruction Manual should include all the details that are needed to use a Fisher Price Mattel. Full manuals and user guide PDFs can be downloaded from Manualsnet.com.

The best way to navigate the Fisher Price Mattel Cozy Fit Infant-to-Toddler High B2111 Chair Instruction Manual is by checking the Table of Contents at the top of the page where available. This allows you to navigate a manual by jumping to the section you are looking for.

This Fisher Price Mattel Cozy Fit Infant-to-Toddler High B2111 Chair Instruction Manual consists of sections like Table of Contents, to name a few. For easier navigation, use the Table of Contents in the upper left corner.

You can download Fisher Price Mattel Cozy Fit Infant-to-Toddler High B2111 Chair Instruction Manual free of charge simply by clicking the “download” button in the upper right corner of any manuals page. This feature allows you to download any manual in a couple of seconds and is generally in PDF format. You can also save a manual for later by adding it to your saved documents in the user profile.

To be able to print Fisher Price Mattel Cozy Fit Infant-to-Toddler High B2111 Chair Instruction Manual, simply download the document to your computer. Once downloaded, open the PDF file and print the Fisher Price Mattel Cozy Fit Infant-to-Toddler High B2111 Chair Instruction Manual as you would any other document. This can usually be achieved by clicking on “File” and then “Print” from the menu bar.