Fender Mustang Floor 2301063000 240V 50Hz AUS DS Pedal Owner's Manual PDF

1 of 12
1 of 12

Summary of Content for Fender Mustang Floor 2301063000 240V 50Hz AUS DS Pedal Owner's Manual PDF

MUSTANG FLOOR BY FENDER

ADVANCED OWNER'S MANUAL

MUSTANG FLOOR

Contents Getting Started! 2

Data Wheel 2

Footswitch Modes 3

Tap/Tuner 3

Amplifier Menus 4

Effects Menus 4

Expression Pedal 5

EXP-1 and MS-4 6

Saving Presets 7

Utility Menus 7

Output Jacks 8

Aux/Phone Jacks 8

Insert Loop 9

USB Port 9

MIDI 9

Factory Restore & Firmware Update 9

FAQ 9

MIDI Appendix 10

Getting Started! USB EXP-1/

MS-4 GROUND

LIFT PHONESAUX IN XLR OUTLEVELUNBALANCED OUT MIDIR L

R L OUT IN

INSERT LOOPINPUT POWER SEND RETURN I

0

13 4 5 2

The basic Mustang Floor setup: 1. Plugthesuppliedpoweradapterintoagroundedoutlet.

2. PressthePOWERswitchtothe"1"positiontoturntheMustang Flooron.

3. PlugyourguitarintotheINPUTjack.

4. ConnecttheinputofyourguitaramplifierorPAsystemtothe LUNBALANCEDOUTjackORplugyourheadphonesintothe PHONESjack.

5. TurntheLEVELknobtoatleasthalfwayup.

The LEVEL knob controls the output level of all the analog outputs on the Mustang Floor, including the UNBALANCED OUT jacks, the XLR OUT jacks and the PHONES jack.

6. Turn on your PA system or guitar amplifier OR put on your headphonesandstartexploringtheMustangFloor!

7. Be sure to power off your amplifier (or PA) before powering downtheMustangFloor.

The Mustang Floor is fully integrated with Fender FUSE software which allows you to configure and operate the Mustang Floor with ease from your computer. You can use Fender FUSE to download free presets from Fender artists; backup and restore presets for different occasions; and

customize the Mustang Floor in ways not available from the Mustang Floor alone. Please download the latest version of Fender FUSE, free of charge from fuse.fender.com.

Data Wheel TurnthebigDATAWHEELtoselectpresetsinplaymode (presstheEXITbutton,iflit,toreturntoplaymode):

PresstheDATAWHEELtoseebasicinformationaboutthecurrent preset, such as the current amplifier model and the effects assignedundereachofthefoureffectcategories:

PEDAL

PEDAL

Push to view the Preset Information screen

PresstheDATAWHEELasecondtimetoseewhereeacheffect is locatedintheguitarsignalprocessingpath:

PEDAL

PEDAL

Push twice to view the Signal Path screen

x2

You can change the order of effects in the signal path to create unique sounds using Fender FUSE software.

TheDATAWHEELhasmanyfunctions!Enterany edit mode by pressing one of the buttons below thescreenandtheDATAWHEELisusedtonavigate and edit in the menu currently being displayed. Dependingonthemenu,youwillpressorturnthe DATA WHEEL to select items and adjust settings, as described in this manual and shown on screen. Using the DATA WHEEL is intuitive, but if you ever getlost,justpressEXITtoreturntoplaymode.

2

MUSTANG FLOOR

Footswitch Modes PresstheMODEbuttontoswitchbetweenPRESETand FXSELECTmodes:

PRESET Mode

PUSHHOLD TO EDIT

STOMPINSERT MOD DELAY REVERB

TAP/TUNER

1

UP

2 3 4 5

BANK

USTANG FLOORTM

MODE PRESET / FX SELECT

EXIT

PEDAL

SAVE

UTIL

REVERBDELAYMODSTOMPAMP

In PRESET mode the green LED lights up and the bottomfivefootswitchbuttons(05,16,27,38,49) are used to select presets from the current bank of fivepresets.PresstheBANK/PRESETbuttonstoselect different banks of five presets to choose from, then press one of the numbered footswitch buttons to

selectapresetfromthebankasdisplayedonscreen.

MUSTANG FLOORTM

STOMPINSERT MOD DELAY REVERB

TAP/TUNERMODE PRESET / FX SELECT

BANK / PRESET

0 5 2 7 3 8 4 91 6

Select Presets from the current Bank

Select Preset Banks

FX SELECT Mode

PUSHHOLD TO EDIT

STOMPINSERT MOD DELAY REVERB

TAP/TUNER

1

UP

2 3 4 5

BANK

MUSTANG FLOORTM

EXIT

PEDAL

SAVE

UTIL

REVERBDELAYMODSTOMPAMP MODE

PRESET / FX SELECT

In FX SELECT mode the red LED lights up and the bottom five footswitch buttons (INSERT, STOMP, MOD, DELAY, REVERB) are used to select/bypass effects for the current preset (the INSERT button selects/bypasses external effects connected to the INSERTLOOPjacks).PresstheBANK/PRESETbuttons

toselectpresetsupor down,oneatatime.

MUSTANG FLOORTM

STOMPINSERT MOD DELAY REVERB

TAP/TUNERMODE PRESET / FX SELECT

BANK / PRESET

0 5 2 7 3 8 4 91 6

Select / bypass Effects

Select Presets

Each FX Select footswitch button will function only when an effect is assigned to that category for the current preset. See Effect Menus on page 4 to choose effects.

Tap / Tuner

TAP/TUNER

UsetheTAP/TUNERbuttonto:

Tapindelaytimeormodulationrateeffectsettings Activatetheon-boardguitartuner

TAP Button Wheneitheradelayormodulationeffectisactive,theLEDnextto theTAP/TUNERbuttonwillblink insyncwiththeeffecttime/rate setting(modulationratescanhaveupto12secondintervalsand the LED may blink infrequently). If both a delay and modulation effectareactivesimultaneously,theLEDwillblinkinsyncwiththe delayeffectandtheTAP/TUNERbuttonwillonlycontrolthedelay time setting (you can bypass the delay effect temporarily if you wanttousetheTAP/TUNERbuttontosetthemodulationrate).

You can use the effect settings menus or Fender FUSE to set delay time and modulation rates more precisely.

Using TAP to set effect time/rate settings: 1. SelectadelayormodulationeffectthatcausestheTAP/TUNER

LED to blink, using the effects menus (see "Selecting Effects" underEffectsMenus,page 4).

2. Press the TAP/TUNER button rhythmically (twice minimum) in time with the desired interval. If you press the TAP/TUNER button only once, the interval will be set to the maximum value. You can see the maximum/minimum values for the currenteffectintheeffectsettingsmenu(seepage5).

Watch the actual time/rate TAP values change while you are tapping them in, by opening the effect settings menu!

TUNER Button The Mustang Floor has a built-in Tuner mode that displays a chromaticguitartuneronscreen.

To use the Tuner: 1. Press and hold the TAP/TUNER button until the Tuner screen

appears.

2 Strike any single string on your guitar and watch the screen. The note of the string being tuned is displayed along with a finetuningneedle:

3. Turnthetuningpegonyourguitaruntilthefinetuningneedle indicatesthestringisintune,asshownabove.

4. PressEXITorTAP/TUNERtoexitfromtheTuner.

3

MUSTANG FLOOR

Amplifier Menus Bypassing Amp Settings

You can turn on or off (bypass) all amp settings that have been selected for the current preset by pressing

the AMP button. The amp menus contain amplifier modeling selections,andsettingsforavarietyofparameterssuchastone, gain,volume,andspeakercabinetsimulation.

PEDAL

PEDAL

The Amp name is highlighted and the AMP button lights up when

Amp settings are active

PresetInformationscreen

Selecting Amplifier Models

1. PressandholdtheAMPbuttonuntiltheampmenuopens.

2. TurntheDATAWHEELtoselectoneof13amplifiermodels:

AMP MODELS '57 Deluxe '65 Princeton British '60s American '90s '59 Bassman '65 Twin Reverb British '70s Metal 2000 '57 Champ Super-Sonic (Burn) British '80s Studio Preamp '65 Deluxe Reverb

3 PressEXITtoreturntoplaymode.

Adjusting Amplifier Settings

1. PressandholdtheAMPbuttonuntiltheampmenuopens.

2. PresstheDATAWHEELoneormoretimesuntilthesettingthat youwant toadjust ishighlighted, then turn theDATAWHEEL to adjust the setting. (Press the DATA WHEEL repeatedly to access"Page2"oftheamplifiersettings.)

"PAGE 2" of the Amp settings

Press the DATA WHEEL repeatedly to select the next Amp setting

You can hold down the AMP button and turn the DATA WHEEL to scroll through settings faster! To de-select a highlighted amp setting, press and hold the AMP button momentarily.

3. PressEXITtoreturntoplaymode.

Effects Menus Bypassing Effects Youcanturnonoroff(bypass)effectsthathavebeenselectedfor thecurrentpresetbypressingthecorrespondingeffectbutton.

The Effect name is highlighted and the Effect button lights up when an

effect is active

PresetInformationscreen

Effects can also be bypassed (turned on-off) using the footswitch buttons when in FX SELECT mode.

Effects that are shown on screen as "EMPTY" can not be activated until an effect has been selected in that category (see SelectingEffects,below).

Selecting Effects

Stompboxeffects Modulationeffects

Delayeffects Reverbeffects

To select Effects: 1. Press and hold one of the four effects buttons to open the

effectsmenu.

2. Turn the DATA WHEEL to select one of the corresponding effects:

STOMPBOX MODULATION DELAY REVERB Overdrive Sine Chorus Mono Delay Small Hall Wah Triangle Chorus Mono Echo Filter Large Hall Touch Wah Sine Flanger Stereo Echo Filter Small Room Fuzz Triangle Flanger Multitap Delay Large Room Fuzz Touch Wah Vibratone Ping Pong Delay Small Plate Simple Compressor Vintage Tremolo Ducking Delay Large Plate Compressor Sine Tremolo Reverse Delay Ambient

Ring Modulator Tape Delay Arena Step Filter Stereo Tape Delay Fender '63 Spring Phaser Fender '65 Spring Pitch Shifter

3. PressEXITtoreturntoplaymode.

You can switch to a different effects category at any time, even while you are in the effects selection menus, by pressing and holding a different Effects button.

Adjusting Effect Settings

1. Press and hold one of the four effect buttons (STOMP, MOD, DELAY,REVERB)toopenthecorrespondingeffectsmenu.

2. Turn the DATA WHEEL to select the effect you want to work with.

4

MUSTANG FLOOR

3. PresstheDATAWHEELoneormoretimesuntilthesettingthat youwant toadjust ishighlighted, then turn theDATAWHEEL toadjustthesetting.

You can also hold down an Effect button and turn the DATA WHEEL to scroll through settings faster!

Press the DATA WHEEL repeatedly to select the next Effect setting

4. PressEXITtoreturntoplaymode.

You can bypass an effect at any time, even while you are in the effect settings menus, by pressing the Effect button, or corresponding footswitch button (when in FX SELECT mode).

Expression Pedal

Your Mustang Floor is equipped with a dual-mode expression pedal. Switch between Volume mode and Expression mode by pressing down hard on the toe end of the pedal. An icon in the upperrightcornerofthescreendisplaysthecurrentpedalmode. "VOLUME OFF" or "EXP OFF" appears if the current pedal mode is set to "off" for the current preset in the Volume Enable or ExpressionBehaviorpedalmenusbelow.

Volume mode icon Expression mode icon

Volumemodeisusedtocontrolmastervolume(orthepedal canbesettooffinVolumemode).

Expressionmodecanbeusedtocontrolalmostanyeffector ampparameterontheMustangFloor(orthepedalcanbeset tooffinExpressionmode).Somecommonusesaretocontrol the frequency parameter of a Wah effect or the rate/time parameterofamodulationordelayeffect.

Pedal Menus

 PressthePEDALbuttontoconfiguretheMustangFloor expressionpedalaswellasanexternalEXP-1expression pedal (optional) when connected. Press the PEDAL

button repeatedly to access each of the pedal menus described below.Manymenuitemsaredynamicandonlyappearunderthe appropriateconditions.Forexample,ifExpressionBehaviormode issetto"off,"noneoftheparametermenusforExpressionmode willappear.Likewise,allEXP-1pedalparameterswillappearonly when an EXP-1 pedal is connected to the Mustang Floor. Note: EXP-1menuitemsareprefacedwith"EXP-1"insteadof"FLOOR"on screen.

The current Volume or Expression mode state of the pedal is stored with the current preset when you save a preset. See "Pedal Default" under Utility Menus on page 7 to override.

VOLUME MODE MENUS

Volume Enable (On/Off) Select "On" if you want the pedal to controlthemastervolumelevelinVolumemode,orselect"Off"if youwantthepedaltobeoffinVolumemode.

Global Volume Heel / Global Volume Toe (0100%) Use thesemenustosetthemastervolumelevelwiththeheelofthe pedal inthefullydownposition(HeelVolume)andwiththetoe ofthepedalinthefullydownposition(ToeVolume).

The Global Volume Heel and Toe settings are stored globally and affect all presets. Every other pedal parameter is stored locally and affects an individual preset.

EXPRESSION MODE MENUS

Expression Behavior (Off, Amp, Stomp, Mod, Delay, Reverb, Volume) Selectthecategorythatyouwanttocontrolwiththeexpression pedalinExpressionmodeorselect"Off"ifyouwantthepedalto beoffinExpressionmode.

You must have an effect selected for the current preset on the Mustang Floor to make that category of effect become available for selection in this menu.

Expression Parameter (Variable) Select the parameter that you want to control with the pedal in Expression mode. Your options will change depending on the category you selected in the Expression Behavior menu above, and the effect module selectedforthecurrentpreset.

Expression Heel / Expression Toe (Variable)Usethesemenus tosettheleveloftheactiveparameterwiththeheelofthepedal in the fully down position (Heel Setting) and with the toe of the pedal in the fully down position (Toe Setting). Your options will change depending on the category you selected in the ExpressionBehaviormenu,above.

Expression Mode (Capture, Live) If "Live" is selected, the cur- rent pedal position will override the stored preset setting for the assigned expression pedal parameter when a preset is first selected. If "Capture" is selected, the pedal is disabled until you movethepedalafterapresethasbeenselected.

5

MUSTANG FLOOR

Bypass Effect (On/Off)Select"On"tobypasstheeffectcurrent- lyselectedintheExpressionBehaviormenuwhenswitchingthe pedaltoVolumemodeorselect"Off"toleavetheeffectactive.

Reset Parameter to Preset Value when Switching to Volume Mode (On/Off) Select "On" to return the Expression Mode ParametertothestoredpresetvaluewhenswitchingtoVolume mode. Select "Off" if you want the parameter be left set to the positionofthepedalwhenswitchingtoVolumemode.

Pedal Calibration Occasionally it may become necessary to calibrate the Mustang Floor's expression pedal and/or an EXP-1 expression pedal con- nectedtotheMustangFloor,toresettheparameterrangeofthe pedal(s)toensureconsistentperformance.

To calibrate the expression pedal and EXP-1 pedal: 1. (Optional)PluganEXP-1pedalintothe"EXP-1/MS-4"jackon

thebackoftheMustangFloorusingtheincludedcable.

2. TurntheMustangFlooroff.

3. Press and hold the UTIL button on the Mustang Floor while turningtheMustangFloorbackon.ContinueholdingtheUTIL buttondownuntilitisnolongerilluminated.

4. Rock the Mustang Floor expression pedal (and the EXP-1, if connected), through the full range of motion between heel andtoepositions.

5. The Mustang Floor expression pedal and the EXP-1, if con- nected,havebeencalibrated!

Pedal Tension Occasionallyitmaybecomenecessarytoadjustthetensionofthe axlenutontheexpressionpedaltoincreaseordecreasetheease ofpedalmovement.

To adjust pedal tension: Pryoffthecircular"F"capfromtherightsideofthepedalwitha small flat blade screwdriver, then use a 10 mm socket wrench to adjusttheaxletension.Donotover-tightentheaxlenuttoavoid damagingthepedalassembly.

10 mm

EXP-1 & MS-4 USB

EXP-1/ MS-4

GROUND LIFT

PHONESAUX IN XLR OUTLEVELUNBALANCED OUT MIDIR L R L

OUT IN

INSERT LOOPINPUT POWER SEND RETURN I

0

Your ustangFloorgivesyoutheoptionofaddingan external EXP-1 expression pedal and an MS-4 four- button footswitch for additional flexibility. Both the EXP-1andMS-4canbeconnectedtogetherthroughthe

EXP-1/MS-4jackonthebackoftheMustangFloor.

To use the EXP-1 and MS-4 simultaneously, plug the EXP-1 into the Mustang Floor and then plug the MS-4 into the second jack on the EXP-1.

EXP-1 Expression Pedal (P/N 2301050000)

Configure the EXP-1 expression pedal through the pedal menus (seePedalMenus,page5).TheEXP-1onlyfunctionsinExpression modewhenconnectedtotheMustangFloor.ThegreenLEDindi- cateswhentheEXP-1pedal ispoweredonandthe redLED indi- cateswhetherExpressionmodeiscurrentlyenabled.

MS-4 Four-Button Footswitch (P/N 0080996000) TheMS-4footswitchdisplayandLEDsshowyoumuchofthesame informationastheMustangFloorscreen,soyoucanforexample, tune your guitar and select presets by watching the footswitch without ever looking at the screen onboard the Mustang Floor! TheMS-4allowsyouto:

SelectQuickAccesspresets(QA1/QA2/QA3)

Selectpresets(up/down/bank)

Bypasseffects

ActivatetheTuner

The footswitch has three modes that are identified by the three LEDslabeledMODE1,MODE2andMODE3.Thefootswitchalso has a Tuner mode which is indicated when all of the mode LEDs areoff.

To switch between modes, press the MODE button. To activate Tunermode,pressandholdtheMODEbutton.

Mode 1SelectoneofthreeQuickAccesspresetsusingthebut- tonslabeled:QA1/QA2/QA3(inlinewiththeMODE1LED).The numberofthepresetwillappearinthedisplayofthefootswitch.

You can assign any preset to be a Quick Access preset in the utility menus. (see Utility Menus, page 7).

Mode 2Select presets down/up, or in banks of 10, using the buttons labeled: DOWN / UP / BANK (in line with the MODE  2 LED).Thenumberof thepresetwillappear inthedisplayof the footswitch.

6

MUSTANG FLOOR

Mode 3Bypass the Stompbox, Modulation or Delay effects, using the buttons labeled: STOMP / MOD / DELAY (in line with the MODE  3 LED). The footswitch button LEDs indicate the effectsthatareactive.

Tuner ModePress and hold the MODE button to activate the Tuner.ThescreenontheMustangFloorandthefootswitchboth displaytunerinformation.Thefootswitchwilldisplaythenearest noteandthebuttonLEDswillindicatesharpandflat."Intune"is indicatedwhenthegreenLEDbelowthefootswitchdisplaylights up.PressanyfootswitchbuttontoexitTunermode.

Saving Presets YourMustangFloorgivesyouthepowerfulabilitytosaveevery settingontheunitaspartofapreset.Whenyouselectapreset, everyeffectsetting,ampsettingandexpressionpedalparameter isinstantlyrecalledtoyourpre-programmedsettings.

The SAVE button will light up red when you edit any setting on the Mustang Floor. This indicates that you

havetemporarilymodifiedthecurrentpreset.Youcanundoyour modificationssimplybyselectingadifferentpresetandthenback againtothepresetyoustartedfrom.

The EXIT button will not cancel temporary changes to the current preset. Only by selecting a different preset using the DATA WHEEL, Footswitch, or Fender FUSE, will your temporary changes be erased.

To save your own custom presets: 1. To save a custom preset, first modify an existing preset by

changinganysetting(s)thatyouchoose.

2. PresstheSAVEbutton.TheSAVEandEXITbuttonsshouldlight up.YoucanpressEXITatthispointtocancelthesaveprocess.

3. Turn the DATA WHEEL to select a preset destination to overwrite.

4. Press the DATA WHEEL if you want to edit the name of your new preset. Use the soft-key buttons to perform the corresponding functions shown along the bottom of the screen.TurntheDATAWHEELtoselectcharacters.

5. PresstheSAVEbuttonasecondtimetoconfirmthesave.Your newpresethasbeencreated!

Memory Lock must be off to save presets (see "Memory Lock" under the Utility Menus, below).

Utility Menus Press the UTIL button to activate the utility menus. PresstheUTILbuttonrepeatedlytostepthrougheach

oftheutilitymenus.TurntheDATAWHEELtomakeselections.All Utilitymenusettingsarestoredgloballyandaffectallpresets.Some of the descriptions below cover multiple menus and are not in the exactsameorderinwhichtheyappearontheMustangFloor.

For the best results when connecting the Mustang Floor into the INPUT jack on a guitar amplifier (rather than the power amp input), set your amp as clean as possible using a low gain setting and start with your BASS and TREBLE tone controls turned down and your MID tone control turned up, then adjust as needed.

Output Configure (Mono/Stereo) If "Mono" (default) is selected, leftandrightchannelsaresummedtogetherprior totheoutput voicing and bass/treble menus below; you can independently set the voicing and bass/treble settings for the left and right UNBALANCEDOUTjacksandXLROUTjacksonlywhentheoutput configure menu is set to "Mono." Select "Stereo" to send stereo leftandrightchannelsignals to the leftandrightUNBALANCED OUTjacksandXLROUTjacks.

Left / Right Output Voicing -OR- Output Voicing (PA System, PA+Bass, PA+Treble, PA Mid-Scoop, Combo Amp, Combo+Bass, Combo+Treble, Combo Mid-Scoop, Stack Amp, Stack+Bass, Stack+Treble, Stack Mid-Scoop) When the Output Configure menu (above) is set to "Mono" you can inde- pendentlychoosethe"voicing"ofthesignalssentoutthroughthe leftandrightUNBALANCEDOUTjacksandXLROUTjacks.When the Output Configure menu is set to "Stereo," only one Output Voicing menu is available and both left and right channels must be set to the same voicing. The voicing options are active only when the Amp settings are active (not bypassed) and a speaker cabinetisselectedwithintheAmpsettings(seeAmplifierMenus, page 4). While the PHONES jack is used, output voicing is inter- nallysetto"PASystem"forallanalogoutputs(UNBALANCED,XLR andPHONES,butnotUSB)andthesettingsselected inthevoic- ingmenusaretemporarilyignored.

Itisrecommendedthatyoustartwithoneofthe3mainvoicings (PASystem,Combo,orStack)andthenchooseoneofthealterna- tives (+Bass, +Treble, Mid-Scoop) only if you find the main set- tings lacking in bass, treble,or having toomuchmid-frequency response.

Below are some suggested ways you can use the Output Configure menu settings combined with the Output Voicing menus:

1. Mono combo guitar amplifier (default): Set Output Configure to "Mono" and set either Left Output Voicing or Right Output Voicingto"Combo,"correspondingtotheleftorrightjackyou areusing.

L UNBALANCED

OUTPUT

(OR XLR OUTPUT)

R UNBALANCED

OUTPUT

(OR XLR OUTPUT)

L UNBALANCED

OUTPUT

(OR XLR OUTPUT)

R UNBALANCED

OUTPUT

(OR XLR OUTPUT)

L UNBALANCED

OUTPUT

(OR XLR OUTPUT)

R UNBALANCED

OUTPUT

(OR XLR OUTPUT)

7

MUSTANG FLOOR

2.Stereo PA system: Set Output Configure to "Stereo" and set OutputVoicingto"PASystem."

L UNBALANCED

OUTPUT

(OR XLR OUTPUT)

R UNBALANCED

OUTPUT

(OR XLR OUTPUT)

L UNBALANCED

OUTPUT

(OR XLR OUTPUT)

R UNBALANCED

OUTPUT

(OR XLR OUTPUT)

L UNBALANCED

OUTPUT

(OR XLR OUTPUT)

R UNBALANCED

OUTPUT

(OR XLR OUTPUT)

3.MonoPAsystem-AND-Monomonitor(orcomboamplifier):Set OutputConfigureto"Mono,"thensetRightOutVoicingto"PA System"andLeftOutVoicingto"Combo."

L UNBALANCED

OUTPUT

(OR XLR OUTPUT)

R UNBALANCED

OUTPUT

(OR XLR OUTPUT)

L UNBALANCED

OUTPUT

(OR XLR OUTPUT)

R UNBALANCED

OUTPUT

(OR XLR O PUT)

L UNBALANCED

OUTPUT

(OR XLR OUTPUT)

R UNBALANCED

OUTPUT

(OR XLR OUTPUT)

Left / Right Bass, Left / Right Treble -OR- Bass / Treble  (0%-100%) Use these utility menus to adjust the bass and treble levelsof thesignals sent fromtheUNBALANCEDOUT,XLROUT, and PHONES jacks. Select "0%" for the least amount of bass/ treble and select "100%" (default setting) for maximum bass/ treble.WhentheOutputConfiguremenu(above)issetto"Mono" you can set the bass and treble levels independently for the left andrightUNBALANCEDOUTjacksandXLROUTjacks.Whenthe OutputConfiguremenuissetto"Stereo,"onlyoneBassandone Treblemenuareavailableandboth leftandrightchannelsmust besettothesamesetting.

Memory Lock (On/Off) Use this menu to prevent accidental preset modifications. You will still be able to make temporary changestopresetswithmemorylockon,butyouwon'tbeable tosavethosechangesuntilmemorylockisswitchedoff.

Pedal Default (From Preset/From Pedal)Select"FromPreset"ifyou wantthepedalmode(volumeorexpression)toalwaysbesetto the mode last stored with each preset, or select "From Pedal" if youwanttooverridethestoredpresetpedalmodeandkeepthe pedalinwhatevermodeit'scurrentlyinwhenyouselectapreset.

Quick Access #1 / #2 / #3 (Preset 00-99) Use these three utility menustochooseQuickAccesspresets.Youcanthenaccessthose presets quickly from the MS-4 footswitch (see MS-4 on page 6). ThesemenusappearonlywhenanMS-4isconnected.

LCD Contrast (0-100) Use this menu to adjust the contrast of theMustangFloordisplay.

MIDI In Channel (1-16, Omni)SelecttheMIDIreceivingchannel.

MIDI Out Channel (1-16)SelecttheMIDItransmittingchannel.

MIDI Through (On/Off) Turn MIDI echo on or off. Note: Sysex packets are not echoed. If you are using the Mustang Floor withothergear that requiresSysex, it is recommendedthat the MustangFloorisplacedattheendofyourMIDIchain.

Pedal Volume CC# / Pedal Expression CC# (0-127)Selectthe ContinuousControllernumbertransmittedbythepedal level in VolumemodeandinExpressionmodeusingtheseutilitymenus.

Pedal Switch CC# (0-127) Select the Continuous Controller numbertransmittedwhenswitchingthepedalbetweenVolume modeandExpressionmode.

EXP-1 Expression CC# (0-127)SelecttheContinuousController numbertransmittedbytheEXP-1pedallevel.Thismenuappears onlywhenanEXP-1isconnected.

EXP-1 Switch CC# (0-127) Select the Continuous Controller numbertransmittedwhentheEXP-1pedalisswitchedon-off.This menuappearsonlywhenanEXP-1isconnected.

About This Amp This menu displays the Firmware version currentlyrunningontheunit.Usethisinformationtodetermine ifanupdateisavailableforyourMustangFloor.

Output Jacks Unbalanced Outputs

USB EXP-1/ MS-4

GROUND LIFT

PHONESAUX IN XLR OUTLEVELUNBALANCED OUT MIDIR L R L

OUT IN

INSERT LOOPINPUT POWER SEND RETURN I

0

TheMustangFloorprovidesunbalancedoutputsforconnectionto monoorstereoamplifiersoracombinationofsoundequipment. Use the utility menus (see Utility Menus, page 7) to adjust the mixing and voicing of the signals sent from these jacks. Use the LEVELknobtoadjusttheoutputleveltoaccommodatetheinput sensitivity of outboard equipment and avoid unwanted signal distortion.

XLR Outputs

USB EXP-1/ MS-4

GROUND LIFT

PHONESAUX IN XLR OUTLEVELUNBALANCED OUT MIDIR L R L

OUT IN

INSERT LOOPINPUT POWER SEND RETURN I

0

The Mustang Floor provides XLR outputs for connection to soundboards and recording equipment when a low signal- to-noise ratio is required. Use the LEVEL knob to adjust the output level to accommodate the input sensitivity of outboard equipment. Use the utility menus (see Utility Menus, page 7) to adjust the mixing and voicing of the signals sent from these jacks.PresstheGROUNDLIFTbuttonINtodisconnecttheground connection which may reduce line noise in some situations. NormallyleavethisbuttonintheOUTposition.

Aux / Phones Jacks Auxiliary Input

USB EXP-1/ MS-4

GROUND LIFT

PHONESAUX IN XLR OUTLEVELUNBALANCED OUT MIDIR L R L

OUT IN

INSERT LOOPINPUT POWER SEND RETURN I

0

 You can use the Auxiliary jack to input audio into your Mustang Floor for accompaniment. Connect the head- phone output on your media player to the AUX IN jack

usingamini-stereocable.Usethevolumecontrolonyourplayer toadjusttheauxiliaryvolumelevel.

8

MUSTANG FLOOR

Phones Jack

USB EXP-1/ MS-4

GROUND LIFT

PHONESAUX IN XLR OUTLEVELUNBALANCED OUT MIDIR L R L

OUT IN

INSERT LOOPINPUT POWER SEND RETURN I

0

Pluginyourheadphones,earbuds,orpoweredspeakers to enjoy the Mustang Floor's stereo features. This jack may also be used as a stereo recording output. The

output voicing is automatically set to "PA SYSTEM" while the PHONES jack is used, internally overriding the output voicing setting in the utility menu. Use the LEVEL knob to adjust the outputlevel.

A headphones icon will appear on screen when the PHONES jack is in use.

Insert Loop USB

EXP-1/ MS-4

GROUND LIFT

PHONESAUX IN XLR OUTLEVELUNBALANCED OUT MIDIR L R L

OUT IN

INSERT LOOPINPUT POWER SEND RETURN I

0

Connect external effects devices to the Mustang Floor using the SEND and RETURN jacks. Connect SEND to the input on your external effects device and connect RETURN

totheoutputonyoureffectsdevice.Theon/offstateoftheinsert loopisstoredaspartofeachpreset.

You can bypass the external effects that you have connected through the INSERT LOOP by pressing the INSERT footswitch button on the Mustang Floor when in FX SELECT mode.

USB Port USB

EXP-1/ MS-4

GROUND LIFT

PHONESAUX IN XLR OUTLEVELUNBALANCED OUT MIDIR L R L

OUT IN

INSERT LOOPINPUT POWER SEND RETURN I

0Use the USB port to connect the Mustang Floor to your computerandtakeyourmusictothenextlevel:

Use Fender FUSE software to control the Mustang Floor fromyourcomputerandaccessbonusfeaturesnotavailable fromtheMustangFlooralone!

Please download the Fender FUSE owner's manual from fuse. fender.com for system requirements.

Record and edit Mustang Floor digital audio using your favoriterecordingsoftware.

MIDI USB

EXP-1/ MS-4

GROUND LIFT

PHONESAUX IN XLR OUTLEVELUNBALANCED OUT MIDIR L R L

OUT IN

INSERT LOOPINPUT POWER SEND RETURN I

0

The Mustang Floor is MIDI (Musical Instrument Digital Interface) compatible. Use the utility menus (seeUtilityMenus,page7) toconfigure MIDI channel settings and select Continuous

Controllernumbers(CC#)foroutgoingexpressionpedalevents.

IncomingMIDIProgramChanges0-99areusedtoselectMustang Floorpresets0-99.IncomingMIDIContinuousControllersareused toadjustMustangFloorparametersaslistedintheMIDIAppendix startingonpage10.

Factory Restore & Firmware Update

Factory Restore YoucanrestoreyourMustangFloortotheoriginalfactorysettings ifdesired.Alluserpresetswillbeerased!

To restore the Mustang Floor to factory settings: 1. Turntheunitoff.

2. Press and hold the EXIT button while turning the unit back on. Continue holding the EXIT button until it is no longer illuminated.

! The FACTORY RESTORE function will erase all user modified presets. It will also remove any custom effect selections that have been modified using Fender FUSE software.

Firmware Update From time to time, Fender may make available firmware updates for your Mustang Floor to improve operation or to add new features. To update the firmware on your unit you will need to connectitthroughtheUSBporttoacomputerwithFenderFUSE softwareandaninternetconnection.

Please see the Fender FUSE manual at fuse.fender.com for details.

FAQ Thereareseveralgreatplacesyoucangotolearnmoreaboutyour MustangFloor:

www.fender.com/support

JoinaFenderCommunityforumwhereyoucanaskquestions andreadthreads.There'sevenaforumjustfortheMustang: www.fender.com/community/forums

Log on to the Fender Knowledge Base to download and read "Frequently Asked Questions" (FAQ): www.fender.com/ community/forums/faq.php

9

MUSTANG FLOOR

MIDI Appendix

Stomp CC's Bypass=CC#23(0-63effectOFF,64-127effectON)

CC#28=StompEffect CC#29 CC#30 CC#31 CC#32 CC#33 None = 0 - - - - -

Overdrive = 1 Level Gain Low Mid High Wah = 2 Mix Frequency Heel Freq Toe Freq High Q

Touch Wah = 3 Mix Sensitivity Heel Freq Toe Freq High Q Fuzz = 4 Level Gain Octave Low High

Fuzz Touch Wah = 5 Level Gain Sensitivity Octave Peak Simple Comp = 6 Type - - - -

Compressor = 7 Level Threshold Ratio Attack Time Release Time

Modulation CC's Bypass=CC#24(0-63effectOFF,64-127effectON)

CC#38=ModEffect CC#39 CC#40 CC#41 CC#42 CC#43 None = 0 - - - - -

Sine Chorus = 1 Level Rate Depth Average Delay LR Phase Triangle Chorus = 2 Level Rate Depth Average Delay LR Phase

Sine Flanger = 3 Level Rate Depth Feedback LR Phase Triangle Flanger = 4 Level Rate Depth Feedback LR Phase

Vibratone = 5 Level Rotor Speed Depth Feedback LR Phase Vintage Tremolo = 6 Level Rate Duty Cycle Attack Time Release Time

Sine Tremolo = 7 Level Rate Duty Cycle LFO Clipping Tri Shaping Ring Modulator = 8 Level Frequency Depth LFO Shape LFO Phase

Step Filter = 9 Level Rate Resonance Min Freq Max Freq Phaser = 10 Level Rate Depth Feedback LFO Shape

Pitch Shifter = 11 Level Pitch Detune Feedback Pre Delay Wah = 12 Mix Frequency Heel Freq Toe Freq High Q

Touch Wah = 13 Mix Sensitivity Heel Freq Toe Freq High Q

Delay CC's Bypass=CC#25(0-63effectOFF,64-127effectON)

CC#48=DelayEffect CC#49 CC#50 CC#51 CC#52 CC#53 CC#54 None = 0 - - - - - -

Mono Delay = 1 Level Delay Time Feedback Brightness Attenuation - Mono Echo Filter = 2 Level Delay Time Feedback Frequency Resonance Input Level

Stereo Echo Filter = 3 Level Delay Time Feedback Frequency Resonance Input Level Multitap Delay = 4 Level Delay Time Feedback Brightness Mode -

Ping Pong Delay = 5 Level Delay Time Feedback Brightness Stereo - Ducking Delay = 6 Level Delay Time Feedback Release Threshold - Reverse Delay = 7 Level Delay Time FFdbk RFdbk Tone -

Tape Delay = 8 Level Delay Time Feedback Flutter Brightness Stereo Stereo Tape Delay = 9 Level Delay Time Feedback Flutter Separation Brightness

10

MUSTANG FLOOR

Reverb CC's Bypass=CC#26(0-63effectOFF,64-127effectON)

CC#58 CC#59 CC#60 CC#61 CC#62 CC#63 None = 0 - - - - -

Small Hall = 1 Level Decay Dwell Diffusion Tone Large Hall = 2 Level Decay Dwell Diffusion Tone

Small Room = 3 Level Decay Dwell Diffusion Tone Large Room = 4 Level Decay Dwell Diffusion Tone Small Plate = 5 Level Decay Dwell Diffusion Tone Large Plate = 6 Level Decay Dwell Diffusion Tone

Ambient = 7 Level Decay Dwell Diffusion Tone Arena = 8 Level Decay Dwell Diffusion Tone

63 Fender Spring = 9 Level Decay Dwell Diffusion Tone 65 Fender Spring = 10 Level Decay Dwell Diffusion Tone

Amp CC's Bypass=CC#27(0-63ampOFF,64-127ampON)

CC#68 CC#69 CC#70 CC#71 CC#72 CC#73 CC#74 CC#75 CC#76 CC#77 CC#78 CC#79 None = 0 - - - - - - - - - - -

Fender '57 Deluxe = 1 Gain Ch. Volume Treble Middle Bass Sag Bias Noise Gate Type Cab - - Fender '59 Bassman = 2 Gain Ch. Volume Treble Middle Bass Sag Bias Noise Gate Type Cab Presence Blend

Fender '57 Champ = 3 Gain Ch. Volume Treble Middle Bass Sag Bias Noise Gate Type Cab - - Fender '65 Deluxe Reverb = 4 Gain Ch. Volume Treble Middle Bass Sag Bias Noise Gate Type Cab - -

Fender '65 Princeton = 5 Gain Ch. Volume Treble Middle Bass Sag Bias Noise Gate Type Cab - - Fender '65 Twin Reverb = 6 Gain Ch. Volume Treble Middle Bass Sag Bias Noise Gate Type Cab - -

Fender Super-Sonic (Burn) = 7 Gain Ch. Volume Treble Middle Bass Sag Bias Noise Gate Type Cab Gain2 Master Vol British '60s = 8 Gain Ch. Volume Treble Middle Bass Sag Bias Noise Gate Type Cab Cut Master Vol British '70s = 9 Gain Ch. Volume Treble Middle Bass Sag Bias Noise Gate Type Cab Presence Blend

British '80s = 10 Gain Ch. Volume Treble Middle Bass Sag Bias Noise Gate Type Cab Presence Master Vol American '90s = 11 Gain Ch. Volume Treble Middle Bass Sag Bias Noise Gate Type Cab Presence Master Vol

Metal 2000 = 12 Gain Ch. Volume Treble Middle Bass Sag Bias Noise Gate Type Cab Presence Master Vol Studio Preamp = 13 Gain Ch. Volume Treble Middle Bass - - Noise Gate Type Cab - -

Miscellaneous CC's Pedal Volume = CC# 7

Tuner Toggle = CC# 20 (0-63 Tuner OFF, 64-127 Tuner ON) All FX Bypass = CC# 22 (0-63 All effects OFF, 64-127 All effects ON)

Fx Insert = CC# 27 (0-63 Insert OFF, 64-127 Insert ON) Tap Tempo=CC# 80

Program Changes Values 0-99 select presets 0-99

11

This product is covered by one or more of the following patents: US Pat. 6,222,110

AMPLIFICADORDEAUDIO IMPORTADO POR: Instrumentos Musicales Fender S.A. de C.V., Calle Huerta # 132, Col. Carlos Pacheco, C.P. 228890, Ensenada, Baja California, Mexico.

RFC: IMF870506R5A Hecho en China. Servicio de Cliente: 001-8665045875

A PRODUCT OF: FENDERMUSICALINSTRUMENTSCORPORATION CORONA,CALIFORNIA,USA

Fender, Mustang and Fender FUSE are trademarks of FMIC. Other trademarks are property of their respective owners. Copyright 2012 FMIC. All rights reserved. (ENGLISH) REV. B

(Hazardous Substances Name)

(Part Name)

(PB)

(Hg)

(Cd)

(Cr 6+

)

(PBB)

(PBDE)

x o o o o o x o o o o o x o o o o o O: SJ/T 11363-2006

X: SJ/T 11363-2006

Specifications TYPE: PR 2300

PART NUMBERS: 2301060000 (120V, 60Hz) 2301060000 (120V, 60Hz) DS 2301061000 (110V, 60Hz) TW DS 2301063000 (240V, 50Hz) AUS DS 2301064000 (230V, 50Hz) UK DS 2301065000 (220V, 50Hz) ARG DS 2301066000 (230V, 50Hz) EUR DS 2301067000 (100V, 50/60Hz) JPN DS 2301069000 (220V, 60Hz) ROK DS

POWER REQUIREMENTS: AC/DC ADAPTER: 12VDC 800mA

INPUT IMPEDANCE GUITAR: 1M AUX: 13k

FOOTSWITCHES (OPTIONAL): EXP-1 expression pedal (P/N 2301050000) MS-4 four-button footswitch (P/N 0080996000)

DIMENSIONS 520mm W x 22

Manualsnet FAQs

If you want to find out how the Mustang Floor Fender works, you can view and download the Fender Mustang Floor 2301063000 240V 50Hz AUS DS Pedal Owner's Manual on the Manualsnet website.

Yes, we have the Owner's Manual for Fender Mustang Floor as well as other Fender manuals. All you need to do is to use our search bar and find the user manual that you are looking for.

The Owner's Manual should include all the details that are needed to use a Fender Mustang Floor. Full manuals and user guide PDFs can be downloaded from Manualsnet.com.

The best way to navigate the Fender Mustang Floor 2301063000 240V 50Hz AUS DS Pedal Owner's Manual is by checking the Table of Contents at the top of the page where available. This allows you to navigate a manual by jumping to the section you are looking for.

This Fender Mustang Floor 2301063000 240V 50Hz AUS DS Pedal Owner's Manual consists of sections like Table of Contents, to name a few. For easier navigation, use the Table of Contents in the upper left corner.

You can download Fender Mustang Floor 2301063000 240V 50Hz AUS DS Pedal Owner's Manual free of charge simply by clicking the “download” button in the upper right corner of any manuals page. This feature allows you to download any manual in a couple of seconds and is generally in PDF format. You can also save a manual for later by adding it to your saved documents in the user profile.

To be able to print Fender Mustang Floor 2301063000 240V 50Hz AUS DS Pedal Owner's Manual, simply download the document to your computer. Once downloaded, open the PDF file and print the Fender Mustang Floor 2301063000 240V 50Hz AUS DS Pedal Owner's Manual as you would any other document. This can usually be achieved by clicking on “File” and then “Print” from the menu bar.