Summary of Content for Fender Mustang Floor 2301060000 120V 60Hz Pedal Owner's Manual PDF
TAP Button When either a delay or modulation effect is active, the LED next to the TAP/TUNER button will blink in sync with the effect time/rate setting (modulation rates can have up to 12 second intervals and the LED may blink infrequently)... If both a delay and modulation effect are active simultaneously, the LED will blink in sync with the delay effect and the TAP/TUNER button will only control the delay time setting (you can bypass the delay effect temporarily if you want to use the TAP/TUNER button to set the modulation rate)...
STOMPBOX MODULATION DELAY REVERB Overdrive Sine Chorus Mono Delay Small Hall Wah Triangle Chorus Mono Echo Filter Large Hall Touch Wah Sine Flanger Stereo Echo Filter Small Room Fuzz Triangle Flanger Multitap Delay Large Room Fuzz Touch Wah Vibratone Ping Pong Delay Small Plate Simple Compressor Vintage Tremolo Ducking Delay Large Plate Compressor Sine Tremolo Reverse Delay Ambient
button repeatedly to access each of the pedal menus described below... Many menu items are dynamic and only appear under the appropriate conditions... For example, if Expression Behavior mode is set to "off," none of the parameter menus for Expression mode will appear... Likewise, all EXP-1 pedal parameters will appear only when an EXP-1 pedal is connected to the Mustang Floor... Note: EXP-1 menu items are prefaced with "EXP-1" instead of "FLOOR" on screen...
MS-4 Four-Button Footswitch (P/N 0080996000) The MS-4 footswitch display and LEDs show you much of the same information as the Mustang Floor screen, so you can for example, tune your guitar and select presets by watching the footswitch without ever looking at the screen onboard the Mustang Floor! The MS-4 allows you to:
Left / Right Output Voicing -OR- Output Voicing (PA System, PA+Bass, PA+Treble, PA Mid-Scoop, Combo Amp, Combo+Bass, Combo+Treble, Combo Mid-Scoop, Stack Amp, Stack+Bass, Stack+Treble, Stack Mid-Scoop) When the Output Configure menu (above) is set to "Mono" you can inde- pendently choose the "voicing" of the signals sent out through the left and right UNBALANCED OUT jacks and XLR OUT jacks... When the Output Configure menu is set to "Stereo," only one Output Voicing menu is available and both left and right channels must be set to the same voicing... The voicing options are active only when the Amp settings are active (not bypassed) and a speaker cabinet is selected within the Amp settings (see Amplifier Menus, page 4)... While the PHONES jack is used, output voicing is inter- nally set to "PA System" for all analog outputs (UNBALANCED, XLR and PHONES, but not USB) and the settings selected in the voic- ing menus are temporarily ignored...
Left / Right Bass, Left / Right Treble -OR- Bass / Treble (0%-100%) Use these utility menus to adjust the bass and treble levels of the signals sent from the UNBALANCED OUT, XLR OUT, and PHONES jacks... Select "0%" for the least amount of bass/ treble and select "100%" (default setting) for maximum bass/ treble... When the Output Configure menu (above) is set to "Mono" you can set the bass and treble levels independently for the left and right UNBALANCED OUT jacks and XLR OUT jacks... When the Output Configure menu is set to "Stereo," only one Bass and one Treble menu are available and both left and right channels must be set to the same setting...
Firmware Update From time to time, Fender may make available firmware updates for your Mustang Floor to improve operation or to add new features... To update the firmware on your unit you will need to connect it through the USB port to a computer with Fender FUSE software and an internet connection...
Ping Pong Delay = 5 Level Delay Time Feedback Brightness Stereo - Ducking Delay = 6 Level Delay Time Feedback Release Threshold - Reverse Delay = 7 Level Delay Time FFdbk RFdbk Tone -
Fender Super-Sonic (Burn) = 7 Gain Ch... Volume Treble Middle Bass Sag Bias Noise Gate Type Cab Gain2 Master Vol British '60s = 8 Gain Ch... Volume Treble Middle Bass Sag Bias Noise Gate Type Cab Cut Master Vol British '70s = 9 Gain Ch... Volume Treble Middle Bass Sag Bias Noise Gate Type Cab Presence Blend
PART NUMBERS: 2301060000 (120V, 60Hz) 2301060000 (120V, 60Hz) DS 2301061000 (110V, 60Hz) TW DS 2301063000 (240V, 50Hz) AUS DS 2301064000 (230V, 50Hz) UK DS 2301065000 (220V, 50Hz) ARG DS 2301066000 (230V, 50Hz) EUR DS 2301067000 (100V, 50/60Hz) JPN DS 2301069000 (220V, 60Hz) ROK DS
If you want to find out how the Mustang Floor Fender works, you can view and download the Fender Mustang Floor 2301060000 120V 60Hz Pedal Owner's Manual on the Manualsnet website.
Yes, we have the Owner's Manual for Fender Mustang Floor as well as other Fender manuals. All you need to do is to use our search bar and find the user manual that you are looking for.
The Owner's Manual should include all the details that are needed to use a Fender Mustang Floor. Full manuals and user guide PDFs can be downloaded from Manualsnet.com.
The best way to navigate the Fender Mustang Floor 2301060000 120V 60Hz Pedal Owner's Manual is by checking the Table of Contents at the top of the page where available. This allows you to navigate a manual by jumping to the section you are looking for.
This Fender Mustang Floor 2301060000 120V 60Hz Pedal Owner's Manual consists of sections like Table of Contents, to name a few. For easier navigation, use the Table of Contents in the upper left corner.
You can download Fender Mustang Floor 2301060000 120V 60Hz Pedal Owner's Manual free of charge simply by clicking the “download” button in the upper right corner of any manuals page. This feature allows you to download any manual in a couple of seconds and is generally in PDF format. You can also save a manual for later by adding it to your saved documents in the user profile.
To be able to print Fender Mustang Floor 2301060000 120V 60Hz Pedal Owner's Manual, simply download the document to your computer. Once downloaded, open the PDF file and print the Fender Mustang Floor 2301060000 120V 60Hz Pedal Owner's Manual as you would any other document. This can usually be achieved by clicking on “File” and then “Print” from the menu bar.