Contents

Epson Ensemble HD 8500 User's Guide PDF

1 of 132
1 of 132

Summary of Content for Epson Ensemble HD 8500 User's Guide PDF

Users Guide

2

Copyright Notice All rights reserved. No part of this publication may be reproduced, stored in a retrieval system, or transmitted in any form or by any means, electronic, mechanical, photocopying, recording, or otherwise, without the prior written permission of Seiko Epson Corporation.

The information contained herein is designed only for use with this Epson product. Epson is not responsible for any use of this information as applied to other equipment.

Neither Seiko Epson Corporation nor its affiliates shall be liable to the purchaser of this product or third parties for damages, losses, costs, or expenses incurred by purchaser or third parties as a result of: accident, misuse, or abuse of this product or unauthorized modifications, repairs, or alterations to this product, or (excluding the U.S.) failure to strictly comply with Seiko Epson Corporations operating and maintenance instructions.

Legal Notice This product incorporates copyright protection technology that is protected by U.S. patents and other intellectual property rights. Use of this copyright protection technology must be authorized by Macrovision, and is intended for home and other limited viewing uses only, unless otherwise authorized by Macrovision. Reverse engineering or disassembly is prohibited.

Trademarks Epson is a registered trademark and Epson Exceed Your Vision is a logomark of Seiko Epson Corporation.

PowerLite and PrivateLine are registered trademarks, Ensemble HD is a trademark, and Epson Connection is a service mark of Epson America, Inc.

The DVD Video logo is a trademark of DVD Format/Logo Licensing Corporation.

Manufactured under license from Dolby Laboratories. Dolby, Pro Logic, and the double-D symbol are trademarks of Dolby Laborarories.

DTS and DTS Digital Surround are registered trademarks of Digital Theater Systems, Inc.

General Notice: Other product names used herein are for identification purposes only and may be trademarks of their respective owners. Epson disclaims any and all rights in those marks.

This information is subject to change without notice.

2008 Epson America, Inc. 4/08 CPD-24528

3

Important Safety Instructions

CAUTION: To reduce the risk of electric shock, do not remove the cover (or back). No user serviceable parts inside. Refer servicing to qualified personnel.

WARNING: To reduce the risk of fire or electric shock, do not expose this apparatus to rain or moisture.

The lightning flash with arrowhead, within an equilateral triangle, is intended to alert the user to the presence of uninsulated dangerous voltage within the products enclosure that may be of sufficient magnitude to constitute a risk of electrical shock to persons.

The exclamation point within an equilateral triangle is intended to alert the user to the presence of important operating maintenance (servicing) instructions in the literature accompanying the appliance.

1. Read these instructions.

2. Keep these instructions.

3. Heed all warnings.

4. Follow all instructions.

5. Do not use this apparatus near water.

6. Clean only with dry cloth.

7. Do not block any ventilation openings. Install in accordance with the manufacturers instructions.

8. Do not install near any heat sources such as radiators, heat registers, stoves, or other apparatus (including amplifiers) that produce heat.

9. Do not defeat the safety purpose of the polarized or grounding-type plug. A polarized plug has two blades with one wider than the other. A grounding type plug has two blades and a third grounding prong. The wide blade or the third prong is provided for your safety. If the provided plug does not fit into your outlet, consult an electrician for replacement of the obsolete outlet.

10. Protect the power cord from being walked on or pinched particularly at plugs, convenience receptacles, and the point where they exit from the apparatus.

11. Only use attachments/accessories specified by the manufacturer.

12. Unplug this apparatus during lightning storms or when unused for long periods of time.

13. Refer all servicing to qualified service personnel. Servicing is required when the apparatus has been damaged in any way, such as when the power-supply cord or plug is damaged, liquid has been spilled or objects have fallen into the apparatus, the apparatus has been exposed to rain or moisture, does not operate normally, or has been dropped.

4

Additional Safety Instructions

Do not place the components of this system near sources of heat or in direct sunlight.

Make sure nothing blocks the ventilation openings on any of the components. Allow for sufficient heat dispersion when components are installed on a rack. Do not block or cover the heatsink on the back of the subwoofer.

Where the mains plug is used as the disconnect device, the disconnect device shall remain readily operable.

When unplugging the power cord of any system component, handle it carefully. Hold the plug when unplugging the cord.

This product should be operated only from the type of power source indicated on the marking label. If you are not sure of the type of power supplied in your home, consult your product dealer or local power company.

Do not overload wall outlets, extension cords, or integral convenience receptacles as this can result in a risk of fire or electric shock.

Keep the system components free from moisture, water, and dust.

Do not let insecticides, benzene, or thinner come in contact with any components of the system.

Never push objects of any kind through openings in the system components as they may touch dangerous voltage points or short-out parts that could result in a fire or electric shock. Never spill liquid of any kind on the product.

Except as specifically explained in these instructions, do not attempt to service this product yourself. Refer all servicing to qualified service personnel.

Never disassemble or modify the product in any way. Dangerous electrical voltages inside the components can severely injure you.

When replacement parts are required, be sure the service technician has used replacement parts specified by the manufacturer or have the same characteristics as the original part. Unauthorized substitutions may result in fire, electric shock, or other hazards.

When closing the screen, be careful not to pinch your fingers where the screen closes against the case.

Do not touch the white part of the screen with your hands. Oil from your skin could damage it.

Never look into the projector lens when the lamp is turned on. The bright light can damage your eyes. Never let children look into the lens when it is on.

Dont use the projector outside of the required temperature range of 41 to 95 F (5 to 35 C). Doing so may cause an unstable display and could lead to projector damage.

The lamp(s) in this product contain mercury. Please consult your state and local regulations regarding disposal or recycling. Do not put in the trash.

Allow the projector lamp to cool for one hour before replacing it.

5

Contents Introduction

Getting Started Using the Remote Control . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12 Turning On the System . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13

Turning On Selected Components. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14 Controlling the Screen . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15 Controlling the DVD Player and Other Equipment . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15

Controlling Playback . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15 Selecting Channels on an HD Tuner, Cable Box, or Satellite Receiver . . . . . . . . . . . . . . . . . . . . . . 16 Using the Buttons on the AV Controller . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16

Adjusting the Volume . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17

Watching Movies Inserting a Disc . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19 Playing a DVD. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20

Using Basic Playback Functions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20 Using Other Playback Features. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22

Listening to Music Playing a CD . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23

Using Basic Playback Functions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24 Using Other Playback Features. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25

Playing Audio Files. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 26 Using Basic Playback Functions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 27

Listening to an MP3 Player . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 28 Listening to a Tape Deck . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 29 Listening to AM/FM Radio . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 29

Tuning to the Desired Station . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 29 Using Radio Station Presets . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 30

Connecting and Using Other Components Connecting Video Equipment . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 32

Connecting the Audio Cable for the Video Source . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 33 Linking Audio and Video Sources . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 34

Connecting Audio Equipment . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 36 Setting Up the Remote Control . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 36

Entering the Setup Code for Your Component . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 37 Customizing the Remote Control Menu . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 39

Using the Remote Control to Operate Your Equipment . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 39

Adjusting the Sound, Picture, and Other Settings Using the On-screen Menu System . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 41 Adjusting the Picture . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 42

Adjusting the Color Mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 42 Adjusting the Aspect Ratio . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 43 Adjusting the Picture Quality . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 45

6

Adjusting the Sound. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 46 Using Test Tones to Adjust the Sound . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 47 Changing the Surround Sound Format . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 47 Using Midnight Mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 48

Using Other Features . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 49 Choosing the Language . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 49 Using Parental Controls . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 50

Restoring Factory Defaults . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 51

Cleaning and Maintenance Cleaning. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 53

Cleaning the Screen . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 53 Cleaning the Projector Lens . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 53 Cleaning System Components . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 54

Adjusting the Screen Length. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 54 Manual Screen Adjustment . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 55

Adjusting the Image Position and Focus. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 56 Repositioning the Image. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 56 Focusing and Resizing the Image . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 57

Checking the Projector Lamp. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 58 Checking the Info Menu . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 58 Checking the Warning Light . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 58

Replacing Remote Control Batteries. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 59

Solving Problems Basic Operation Problems . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 61 Picture Problems . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 62 Sound Problems . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 64 Problems Using the Screen . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 65 Problems Using the Remote Control . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 66 Problems Using the DVD Player . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 67 Problems Using the Radio . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 67 Problems Using an External Component . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 68 Where To Get Help . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 69

Internet Support. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 69 Speak to a Support Representative . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 69 Purchase Supplies and Accessories . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 69

Using Advanced Remote Control Features Adjusting the LCD Screen . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 71

Adjusting the Contrast . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 72 Learning Commands from Another Remote Control . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 72

Cloning Your Remote Control . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 74 Advanced Remote Control Setup . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 75

Editing Device Names and Commands . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 75 Setting Up Macros . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 77 Adding or Hiding Pages . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 78 Erasing Learned Buttons and Macros . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 79 Using Remote Control Punch-Through . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 80

7

Using an RF Base Station . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 81 Setting Up an Addressable Base Station . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 81

Restoring Remote Control Factory Defaults. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 83

Remote Control Codes Using the Code Tables . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 85

Recalling Programmed Codes. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 86 Code Tables . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 87

Specifications Playable Disc Types . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 119 Screen Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 120

General. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 120 Built-in Speaker System . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 120

Remote Control Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 120 Powered Subwoofer Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 121

Bass Driver . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 121 Amplifier . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 121 Physical . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 121

Surround Speaker Specifications. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 121 AV Controller Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 122

Notices Responsible Use of Copyrighted Materials . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 123 FCC Compliance Statement . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 123 Declaration of Conformity . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 124 Epson America, Inc. Limited Warranty . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 124

Index

8

9

Introduction

The Ensemble HD home cinema system by Epson is designed to transform your living room into a state-of-the-art home cinema. Its wide-format (16:9) projection screen, 5.1-channel surround sound system, and high-definition video projector deliver unrivaled, high-performance picture and sound.

Your home cinema systems ease-of-use and versatility let you:

Watch movies using the built-in DVD player (see page 19)

Listen to music in various formatsby playing CDs, connecting an MP3 player, or using the built-in AM/FM radio (see page 23)

Connect external components such as a cable box, satellite receiver, gaming console, or high-definition DVD player like Blu-ray or HD DVD (see page 31)

Use the included universal remote control to operate not just the Ensemble HD system, but any components you connect to it

See Getting Started in the next section for basic instructions on using your system.

TM

TM

10

11

Getting Started

The universal remote control included with your Ensemble HD system puts complete control over your home theater in the palm of your hand. With one touch, you can lower the screen, turn on the projector, and get ready to watch a movie. If youve connected additional components to your home theater, such as a cable box or satellite receiver, you can use the remote control to operate them too.

See these sections:

Using the Remote Control on page 12

Turning On the System on page 13

Controlling the Screen on page 15

Controlling the DVD Player and Other Equipment on page 15

Adjusting the Volume on page 17

12

Using the Remote Control Aim the remote control at the screen and press any button. An icon appears on the remote controls LCD screen to indicate that a command is being transmitted. At the same time, the blue light at the top of the projection screen flashes, indicating that the system is receiving a command.

Note The blue light remains on when the screen is raised and turns off when the screen is lowered.

If youre using the remote control in a darkened room, press the LIGHT button on the side of the remote control. The keys and display screen on the remote control light up so you can make a selection. The light shuts off by itself after 10 seconds, or you can turn it off by pressing the LIGHT button a second time.

Note If you need to increase the amount of time the remote control lights up or change the contrast of its screen, see page 71.

Blue light

LIGHT button (on side of remote control)

13

Turning On the System When youre ready to watch a movie, you can lower the screen, turn on the projector, and turn on the AV controller (with its built-in DVD player) with the touch of a button.

1 Make sure the MAIN menu is displayed on the remote control. If necessary, press the MAIN button.

2 Point the remote control at the screen and press the ON button to turn on the system. The screen comes down and the projector and AV controller turn on.

Note Make sure the remote control remains pointed at the screen until the system has turned on. (You see the icon flash on the remote control screen while its turning on the system.) If the system does not turn on, see Basic Operation Problems on page 61.

The projector lamp takes up to 30 seconds to achieve full brightness.

3 When youre done using the system, make sure the MAIN menu is displayed on the remote control and press the OFF button. The projector and AV controller turn off, and the screen raises up automatically.

Note If you install additional components, such as a cable box or satellite receiver, you can set up the remote control to turn them on with one button, too. See Setting Up Macros on page 77.

MAIN

DVD

CABLE

SAT

HD

RADIO

1 OF 2

ON button MAIN button

14

Turning On Selected Components

You can turn on and operate any component in the system without using any of the others. For example, if you want to listen to your home theaters built-in radio, you can turn on the radio by itself without lowering the screen.

1 Make sure the MAIN menu is displayed on the remote control. If necessary, press the MAIN button.

You see a list of components displayed on the remote control:

2 If you dont see the component you want to use, it may be listed on the next page. Press the PAGE or (page up or down) button to access additional components.

3 Press the button to the right of the component you want to use, such as DVD or RADIO. The top of the screen changes from MAIN to the name of the component you select, and the menu options change to the ones for that component.

Note Some of the options in the MAIN menu, such as CABLE or SAT, are for components that dont come with the Ensemble HD system, such as a cable box or satellite receiver. If you install components like these, you can use the remote control to operate them just like the rest of your system. See Connecting and Using Other Components on page 31 for more information.

4 Once youve opened the menu for the selected component, press the ON button to turn it on or the OFF button to turn it off. (If you select DVD or RADIO, the AV controller turns on automatically.)

5 Follow the instructions elsewhere in this guide to operate the selected component:

If you selected RADIO, you can listen to AM/FM radio through your home theater (see page 23).

If you selected DVD, you can you can play a DVD (see page 19), listen to a CD (see page 23), or listen to a disc with MP3 audio files (page 26).

To use other components you may have added to your system, see page 39.

MAIN

DVD

CABLE

SAT

HD

RADIO

1 OF 2

Press the button for the component you want to use

List of components

Page up and down buttons

15

Controlling the Screen The screen is lowered automatically when you turn on the system as described on page 13. If necessary, you can also operate the screen manually as described below.

Note To change how far the screen comes down when you lower it, see Adjusting the Screen Length on page 54.

1 Make sure the MAIN menu is displayed on the remote control. If necessary, press the MAIN button.

2 Press the PAGE button to display additional components.

3 Press the button to the right of PROJ to select the projector menu.

4 Press S-DWN to lower the screen. It comes down and automatically stops at the pre-set position.

5 Press S-UP to raise the screen when youre done using it.

Controlling the DVD Player and Other Equipment The universal remote control has all the buttons you need to control the Ensemble HD home theater, along with any additional components you may add to it. Heres an overview of the main buttons youll use to control the built-in DVD player and radio, as well as any optional components like a cable box or satellite receiver.

Note You can also use the buttons on the AV controller for many of the same functions that you would normally access using the remote control. See Using the Buttons on the AV Controller on page 16.

Controlling Playback

Use the buttons shown below to control playback when watching a movie or listening to music:

Note The buttons highlighted at right are for accessing the on-screen menu system and selecting menu options, not for controlling playback. See Using the On-screen Menu System on page 41.

Fast-forward/skip forwardFast-rewind/skip backward

Stop

Play

Pause

16

Selecting Channels on an HD Tuner, Cable Box, or Satellite Receiver

You can use the numeric keypad to select pretuned radio stations or the tracks on a CD. If youve connected an HD tuner or other equipment to receive programmed content, use the numeric keypad to enter channels. The method of entering the digits varies, depending on the type of equipment youre usingfor example, you might have to press 0 to enter a single-digit number, such as 01. In some case, you may need to press the ENT (Enter) or SEL (Select) button to enter the digits.

You can also use CH and (channel up and down) to change channels.

To return to the previously selected channel, press the PREV CH button.

Using the Buttons on the AV Controller

You can use the buttons on the AV controller to control most basic functions.

Note All these functions are accessible via the remote control.

ON/STANDBY lets you turn on the AV controller. The controller is on when the light surrounding the button is blue, and is off (standby) when the light is orange.

SOURCE lets you switch between the Ensemble HD systems DVD player and radio, or select other equipment youve connected to the system. Each time you press the button, the AV controller cycles through these functions or sources:

DVD player FM radio AM radio Audio 1 port Audio 2 port Composite video (CVBS) S-video Component video HDMI 1 HDMI 2

ON/STANDBY button

SOURCE button Playback control buttons

Volume control knob

Eject button

17

The playback control buttons let you control playback when watching a DVD or listening to a CD. In addition, the and buttons let you select preset radio stations while listening to AM or FM radio.

The eject button opens and closes the DVD/CD tray.

The volume control knob lets you adjust the sound volume.

Adjusting the Volume The Ensemble HD system gives you various ways to control the volume:

VOL and (volume up and down) lets you change the volume from 74 to +10 dB.

MUTE temporarily turns off the sound. Press the button again to restore audio.

Midnight Mode adjusts the sound for late-night viewing when you want to avoid disturbing others. Volume is reduced at the bass end with volume highs and lows being compressed to a narrower range. See page 48 for details.

Note You can also adjust the volume using the volume control knob on the AV controller.

To use headphones with your home theater, plug them into the PHONES jack on the front of the AV controller. The jack accepts 1/4-inch stereo headphones. When you plug in the headphones, the sound is automatically muted from the Ensemble HD speakers.

18

19

Watching Movies

Follow the steps in this chapter when youre ready to watch a movie on DVD. See these sections:

Inserting a Disc below

Playing a DVD on page 20

Note If you watch movies under different lighting conditions (for example, in the daytime and at night), you may want to change the Color Mode when you begin watching a movie (see Adjusting the Color Mode on page 42).

Depending on the aspect ratio your movie was filmed in, you may also want to select a different Aspect setting (see Adjusting the Aspect Ratio on page 43).

Inserting a Disc The DVD player, built into the Ensemble HD system, accepts both DVD and DVD-R discs. For more information on compatible formats, see Playable Disc Types on page 119.

1 Make sure the Ensemble HD system is turned on (see Turning On the System on page 13).

2 Open the DVD/CD tray by pressing the eject button on the AV controller. (Or select EJECT from the DVD menu on the remote control.)

Note Make sure you dont have a USB flash drive inserted, or you wont be able to operate the DVD player, or insert or eject a DVD. Remove the flash drive prior to inserting the disc.

3 Place the disc in the tray, playable side down.

4 Close the DVD/CD tray by pressing the eject button on the AV controller. (Or select EJECT from the DVD menu on the remote control.)

When youre done playing the disc, open the DVD/CD tray as described above and remove the disc.

20

Playing a DVD Once the disc is inserted, follow these steps to begin playing the movie:

1 If the DVD player was the last function you used, the DVD begins playing automatically.

If you previously used a different function (such as CABLE or SAT), select the DVD option on the remote control:

2 When the DVD begins playing, you may see a menu screen that lets you select its contents and other options. (This menu varies from disc to disc.) Use the arrow buttons (l r u d) to highlight the option you want, then press the SEL (Select) button. For example, to play a movie, highlight the Play movie option, then press SEL.

3 If you need to return to the DVDs main menu screen while watching the movie, press the MENU or GUIDE button. You can also select MENU from the DVD menu on the remote control.

Note To avoid losing your place while watching a movie, dont switch sources. If you select a different source (such as CABLE or SAT), the DVD will stop playing. It will start over from the beginning when you return to the DVD function.

Using Basic Playback Functions

While youre watching a movie, you can use the following buttons to control playback:

MAIN

DVD

CABLE

SAT

HD

RADIO

1 OF 2

Select DVD

Use these buttons to select DVD menu options

Fast-forward/skip forwardFast-rewind/skip backward

Stop

Play

Pause/step

Time elapsed/time remaining

21

Press the pause button to stop the movie temporarily. The image freezes on the screen. While the movie is paused, pressing the pause button again puts the player in step mode. Each time you press the pause button, the movie advances one frame at a time. To return to normal playback, press the play button.

Press the stop button to stop projection of the movie temporarily. The DVD player remembers the point in the movie where you stopped. Press the play button to resume playback from that point.

Note If you press the stop button twice, playback will start over from the beginning of the movie.

Press the play button to resume playback if youve paused or stopped the movie.

Press the fast-rewind or fast-forward button to skip backward or forward to a different chapter in the movie. DVDs are usually structured with each movie or special feature having its own title, and with each title broken into chapters:

As you skip through chapters, the title and chapter information display at the top of the screen.

Press and hold the fast-rewind or fast-forward button to move quickly through a scene. Each time you press and hold the button, the speed doubles and then finally returns to normal speed:

2 4 8 16 normal speed

Press the INFO button to display title and chapter information on the screen. The on-screen display tells you the time elapsed and time remaining at your current location on the disc. Each time you press the INFO button, you see the following information displayed:

Title time elapsed Title time remaining Chapter time elapsed Chapter time remaining Display off

Note If you press a button for a function that cannot be performed at a given time (for example, if you press the play button while the movie is already playing), you see the symbol on the screen.

22

Using Other Playback Features

You can use the DVD menu on the remote control to access several other features while watching movies.

Note Some functions in the remote controls DVD menu are used only for playing CDs. These include the Shuffle, Memory, and Clear functions.

If your DVD has separate audio tracks in different languages, you can change the language by selecting AUDIO from the DVD menu. Each time you press AUDIO, the language changes and you see an on- screen display like the following:

Note If you usually watch DVDs with a language other than English selected, you can set that language to be used automatically whenever you play a DVD. See Choosing the Language on page 49.

Some DVDs include scenes that have been shot from different camera angles. They have a symbol like this to indicate the number of available angles: . When you encounter a scene with multiple angles, a camera icon is displayed on the screen. Select ANGLE in the DVD menu to change angles. To stop displaying the camera icon, press the INFO button repeatedly until it clears the icon from the screen.

To repeat the current chapter of a movie that youre watching, select RPEAT from the DVD menu. To repeat the entire title (such as the movie itself or a special feature), press RPEAT again. Press RPEAT a third time to cancel the repeat function.

To repeat just part of a scene that youre watching, press A<>B at the beginning of the part you want to repeat, then press A<>B a second time to mark the end of the section. Press A<>B a third time to cancel the repeat function.

To move slowly through a scene, select SLOW from the DVD menu. Each time you press SLOW, the speed is reduced by one-half. You can select from 1/2, 1/4, and 1/8 speed. To return to normal playback, press the play button.

If your DVD has subtitles, you can change the subtitle language by selecting SUB-T from the DVD menu. Each time you press SUB-T, the language changes and you see an on-screen display like the following:

Note If you usually watch DVDs with subtitles, you can have the subtitle language you prefer turned on automatically whenever you play a DVD. See Choosing the Language on page 49.

Audio 5/5:Dolby D 2CH ENGLISH

Subtitle 03/03:FRENCH

23

Listening to Music

Follow these steps when you want to listen to music with your Epson Ensemble HD system. See these sections:

Playing a CD below

Playing Audio Files on page 26

Listening to an MP3 Player on page 28

Listening to a Tape Deck on page 29

Listening to AM/FM Radio on page 29

Note When listening to music, you may wish to change the surround sound format to STEREO. See Changing the Surround Sound Format on page 47.

Playing a CD The DVD player built into the Ensemble HD system can play music CDs as well as movies. The player accepts both commercial CDs and home-recorded CD-R and CD-RW discs. For more information on compatible formats, see Playable Disc Types on page 119.

1 Select the DVD option on the remote control to activate the DVD player:

Note For most CD playing functions, it is not necessary to lower the screen or turn on the projector.

2 Insert the CD just as youd insert a DVD. See Inserting a Disc on page 19.

After a moment, you see the number of tracks and total playing time on the AV controller.

MAIN

DVD

CABLE

SAT

HD

RADIO

1 OF 2

Select DVD

24

3 To begin playing the CD, press the play button.

Note To avoid interrupting CD playback, dont switch sources. If you select a different source (such as CABLE or SAT), the CD will stop playing. It will start over from the beginning when you resume playback.

Using Basic Playback Functions

While youre listening to a CD, you can use the following buttons and the numeric keypad to control playback:

To play a specific track on the CD, use the numeric keypad on the remote control. For example, to select track 3, just press the 3 button. To select track 21, press 2 followed by 1. After pressing the buttons, wait a moment for the selection to be transmitted, or press SEL (Select) to transmit your selection right away.

You can also skip between tracks by using the fast-rewind or fast-forward button. To advance to the next track, momentarily press and release the button without holding it. To go to the previous track, press the button twice (the first time returns you to the beginning of the current track).

The current track and elapsed time are indicated on the AV controller screen.

If the projector is on, you can also display the track and time information on the projection screen by pressing the INFO button. Each additional time you press the INFO button, the displayed information changes (both on the AV controller and on the projection screen) as follows:

Track time elapsed Track time remaining Total time elapsed Total time remaining Display off

Press and hold the fast-rewind or fast-forward button to move quickly through a track. Each time you press and hold the button, the speed changes as follows:

2 4 6 8 2

To return to normal playback, press the play button.

Press the pause button to stop the music temporarily. To resume playback, press play or pause.

Press the stop button when youre done listening to the CD.

Play button

Fast-forward/skip forwardFast-rewind/skip backward

Stop

Play

Pause

Time elapsed/time remaining

25

Using Other Playback Features

You can use the DVD menu on the remote control to access several other features while listening to a CD.

Note Most functions in the remote controls DVD menu are used only for playing DVDs. Only the ones listed below can be used when playing CDs.

To repeat the current track of a CD that youre listening to, select RPEAT from the DVD menu. To repeat the entire CD (or a programmed playlist), press RPEAT again. Press RPEAT a third time to cancel the repeat function. Each time you select this option, the display changes as follows:

Repeat one Repeat all Repeat off

To repeat just part of a track, press A<>B at the beginning of the part you want to repeat, then press A<>B a second time to mark the end of the section. Press A<>B a third time to cancel the repeat function.

To play all the tracks on your CD in a random order, press the stop button if the CD is currently playing. Select SHUFF (Shuffle) from the DVD menu, then press the play button. After all the tracks finish playing, the DVD player stops and the shuffle function is cancelled. To cancel shuffle mode while random playback is in progress, press the stop button, then press SHUFF.

You can play up to 21 tracks in any desired order by creating a playlist. To create a playlist, you need to lower the screen and turn on the projector. Also, press the stop button if the CD is currently playing. Once the projector is turned on, select MEMO (Memory) from the DVD menu on the remote control. You see this screen:

Select the desired track number on the left, using the u or d button on the remote control. Then highlight ADD, using the r button, and press SEL (Select). The track number is added to the list on the right. Repeat for any additional tracks you want to add.

To insert a track at an earlier point in the list, highlight the track in the playlist prior to the point where you want to insert the new track. Then select the desired track number on the left and select INSERT. Use DELETE to erase a track, or CLEAR to erase the whole list.

Once youve finished creating your playlist, highlight PLAY and press SEL (Select) to start playback. The playlist is retained until you remove the CD or turn off the player. To resume normal playback without the playlist, press the stop button, then press play.

01 05

11 13

ADD

PROGRAM LISTTRACK

[15] DELETE

PLAY

CLEAR

Select desired track number Playlist

Total tracks on disc

26

Playing Audio Files You can use the AV controller to play MP3 and WMA audio files stored on a USB flash drive, or on a data CD or DVD.

Note If you burn your MP3 and WMA files to an audio CD instead of a data CD, play the disc as described in Playing a CD on page 23.

You can also display JPG images (stored on a flash drive, data CD, or DVD) by following the instructions below. When you press the play button, your photos display as a slideshow.

1 Make sure the Ensemble HD system is turned on (see Turning On the System on page 13). Youll need the projector turned on in order to select files on the screen.

2 Insert your USB flash drive into the USB slot on the front of the AV controller. (If the files are stored on a CD or DVD, insert the disc as described in Inserting a Disc on page 19.)

3 Select the DVD option on the remote control. (This tells the AV controller to check for an inserted disc or flash drive.)

MAIN

DVD

CABLE

SAT

HD

RADIO

1 OF 2

Select DVD

27

After a moment, you see the contents of the flash drive or CD/DVD displayed on the screen:

Caution Do not remove the flash drive while its data access light is flashing, or you could lose data on the drive. Always stop playback by pressing the stop button before removing the drive.

4 Do one of the following:

Press the play button to play all files from the beginning.

Use the u or d button to highlight the file youd like to start with. (If a file is already playing, press the stop button first.) Then press the play button. All files are played from the selected file to the last

one on the drive.

If your flash drive contains folders, use the u or d button to highlight the desired folder, then press SEL (Select) to view its contents. Highlight the file youd like to start with, then press the play button. Only files in the folder are played.

When youre done listening to music on the flash drive, make sure its data access light is not flashing. (If necessary, press the stop button.) Then pull the drive straight out of the slot.

Using Basic Playback Functions

While youre listening to audio files, you can use the following buttons and the numeric keypad to control playback:

To play a specific file, use the numeric keypad on the remote control. For example, to select file 3, just press the 3 button. To select file 21, press 2 followed by 1. After pressing the buttons, wait a moment for the selection to be transmitted, or press SEL (Select) to transmit your selection right away.

You can also skip between tracks by using the fast-rewind or fast-forward button. To advance to the next track (or go to the previous one), momentarily press and release the button without holding it.

Multimedia Player

ROOT PHOTOS 0 MP3 1Song 1

5Photo 1

MP3 2Song 2

3Song 3

4Song 4 Windows media audio (WMA) files

MP3 files

JPG photo image

Folder containing more files

Fast-forward/skip forwardFast-rewind/skip backward

Stop

Play/resume

Pause

Time elapsed/time remaining

28

The current file and elapsed time are indicated on the AV controller screen. You can also display the file and time information on the projection screen by pressing the INFO button. Each time you press the INFO button, the displayed information changes (both on the AV controller and on the projection screen) as follows:

Time elapsed Time remaining Display off

Press and hold the fast-rewind or fast-forward button to move quickly through a file. Each time you press and hold the button, the speed increases:

2 4 6 8 normal speed

To return to normal playback, press the play button.

Press the pause button to stop the music temporarily. To resume playback, press the play button.

Press the stop button when youre done listening.

Note You can also use the repeat function to repeat one or more files. Select RPEAT from the DVD menu on the remote control. Each time you press RPEAT, you switch between various repeat options.

Listening to an MP3 Player You can connect a personal MP3 player, such as an iPod, to the AUDIO 2 port on the front of the AV controller. Youll need a 1/8-inch stereo mini audio cable, which you can purchase from an electronics retailer.

1 Connect one end of a stereo mini audio cable to the AUDIO 2 port, shown below. Connect the other end to the headphone jack on your MP3 player.

Note Do not connect your MP3 player to the AV controller with a USB cable.

2 Select the AUDIO option on the remote control, then select AUD2. This switches the audio input to your MP3 player.

3 Use the controls on your MP3 player to begin playing music.

29

Listening to a Tape Deck Make sure your tape deck (or other audio source) is connected to the AUDIO 1 port on the back of the AV controller, as described in Connecting Audio Equipment on page 36.

1 Select the AUDIO option on the remote control, then select AUD1. This switches the audio input to your tape deck.

2 Use the controls on your tape deck to begin playing music.

Listening to AM/FM Radio You can use the AV controller to receive AM or FM radio broadcasts. First make sure an antenna is connected, as described in the Installation Guide.

Tuning to the Desired Station

1 Select the RADIO option on the remote control to activate the radio:

Note To use the radio, it is not necessary to lower the screen or turn on the projector.

2 Select the BAND option on the remote control to switch between AM and FM. The display on the AV controller shows the current station:

3 Select TUNE+ or TUNE to change the frequency:

Press the button momentarily and then release it to change the frequency manually.

Or press and hold the button to find the next available station automatically. The tuner searches until a station of sufficient strength has been found, and the word TUNED appears on the display. Weak stations are skipped during the auto-tuning process.

MAIN

DVD

CABLE

SAT

HD

RADIO

1 OF 2

Select RADIO

FrequencyBand

30

Using Radio Station Presets

You can save up to 40 preset stations. Follow these steps to save a station:

1 Tune in the desired station, as described in the previous section.

2 Select the SAVE option in the RADIO menu on the remote control. The preset number flashes on the display:

3 Select the desired preset number (1 through 40):

Use the numeric keypad to enter the numberfor example, to select preset 3, press 0 followed by 3. To select preset 21, press 2 followed by 1.

Or use the or button to select the desired number, then press SAVE again.

Note A preset station is erased from the memory when you store another station in its place.

Once your stations are preset, use either the numeric keypad on the remote control, or the and buttons, to quickly access your favorite stations. You can also use the and buttons on the AV controller.

Preset number

31

Connecting and Using Other Components

To extend the capabilities of your Ensemble HD system, you can add on a variety of audio and video components. You can connect up to a total of five external video devices to the Ensemble HD system, such as a cable box or satellite receiver. You can also connect an external audio device, such as a CD player or tape deck. If you want to connect your own amplifier or sound system, a two-channel (stereo) analog audio output port is provided.

See these sections:

Connecting Video Equipment on page 32

Connecting Audio Equipment on page 36

Setting Up the Remote Control on page 36

Using the Remote Control to Operate Your Equipment on page 39

Note To temporarily connect a personal MP3 player, such as an iPod, use the Audio 2 port located on the front of the AV controller. See page 28.

If desired, you can connect an IR blaster to the IR OUT port to relay signals to your components (such as a cable box or satellite receiver), or use an RF base station. See Using an RF Base Station on page 81.

32

Connecting Video Equipment You can connect up to five pieces of video equipment at the same time, using any of the commercially available cables shown below:

Check your video device for the type of output port(s) it has available. For best picture quality, use the HDMI (High-Definition Multimedia Interface) port. If your equipment doesnt support HDMI, use one of the following ports (highest quality listed first): component video, S-video, or composite video (yellow RCA-style connector).

Connect the cable from your video component to any available port on the back of the AV controller, as shown below:

Caution Avoid connecting or disconnecting any components with your equipment turned on.

Port Cable

HDMI 1 or 2 HDMI cable

Component Component video cable

Note When connecting the cable, match the colors of its connectors to the colors of the ports where youre plugging them in.

S-Video S-video cable

CVBS (composite video) Composite video cable (RCA cable)

Pr Pb Y

HDMI audio/video portsS-video port Component video port

CVBS (composite video) port

33

Connecting the Audio Cable for the Video Source

Once youve connected the video cable, you may need to connect an audio cable in order to combine the picture with sound. If youve connected your device using an HDMI cable, the audio signal is already carried by the cable, so you dont have to connect an additional cable. (Make sure HDMI audio is enabled in your components setup menu.) Otherwise, youll need to connect an audio cable to one of the ports listed below:

* Connection not required if your video device supports HDMI audio.

Check your video device for the type of audio output port(s) it has available. For best sound quality, use either the coaxial or optical digital audio port. If your equipment doesnt have digital audio, use an analog stereo output port instead. Connect the audio cable to one of the ports shown below:

If youve connected to this video port... ...connect an audio cable to one of these ports

HDMI 1 or 2 Coaxial* Optical*

Component Coaxial Optical Analog

S-Video Coaxial Optical Analog

CVBS (Composite video) Coaxial Optical Analog

Coaxial audio port (digital audio)

Analog audio port

Optical audio port (digital audio)

34

Linking Audio and Video Sources

Once youve connected the audio and video cables, you need to tell the Ensemble HD system which audio and video ports to use together. That way, when you select a device with the remote control (VCR, cable, satellite, etc.), the matching audio and video sources will be automatically used. You link the audio and video sources together using the Source Assign screen.

Note The label you assign to a device (e.g. CABLE) is what you see on the projection screen when youre selecting sources. It doesnt affect the device names shown on the remote controls LCD screen.

1 Make sure the MAIN menu is displayed on the remote control. If necessary, press the MAIN button.

2 Point the remote control at the screen and press the MENU button.

You see the Ensemble HD menu screen:

3 Use the d button to highlight Video, then press the SEL (Select) button.

4 Use the d button to highlight Source Assign, then press the SEL (Select) button.

You see the screen shown below. The video port to which youve connected your video equipment is listed in the left-hand column:

Move Enter ExitMenuSel

Video

Language

Preference

Audio

Reset

Voice

Bass

Treble

Surround

Front Distance

Center Distance

Rear Distance

Test Tone

0 dB

0 dB

0 dB

0 dB

5 ft.

5 ft.

5 ft.

d button

Video Input

HDMI1

HDMI2

Component

S-Video

Composite

Move Adjust ExitMenuESC Return

[ S o u r c e A s s i g n ]

Label

Cable

Sat

HD

DVR

Video

Audio Input

HDMI1

HDMI2

Coax

Optical

Analog

35

5 In the left-hand column (under Video Input), locate the name of the port to which youve connected the video cable for your equipment.

6 In the middle column of the same row (under Label), select the type of device youve connected. If youve connected a device not listed below, select an unused name such as AUX. You can select from these labels:

Note You cant select the same label for different inputs. If the label you want is currently selected on another unused input, change the label on the unused input to free up that label.

7 In the right-hand column of the same row (under Audio Input), select the name of the port to which youve connected the audio cable.

For example: If you connected a cable box to the HDMI1 port and the cable box supports HDMI audio, select HDMI1 in the Audio Input column. Or if you connected to the S-Video port, select Coax, Optical, or Analog in the Audio Input column, depending on the port to which you connected the audio cable.

Note Make sure you dont select the same audio input for different video inputs.

8 When youre done changing the settings, press the MENU button to exit the menu system.

Note When youre viewing a particular source, you can press the OSD (On-Screen Display) button to display information about the source.

Label (device name) Description

CABLE Cable box

SAT Satellite receiver

HD High-definition DVD player, such as Blu-ray or HD DVD

DVR Digital video recorder (for example, TiVo)

AUX Video game console

VIDEO Video cassette recorder

36

Connecting Audio Equipment You can connect an external audio device, such as a CD player or tape deck, to the Ensemble HD system. Use an RCA-style stereo cable and connect your equipments audio output port to the AUDIO 1 port on the back of the AV controller, as shown below:

To record from the AV controller to your tape deck, connect the audio input port on your tape deck to the 2CH OUT port, shown above. If youre not using a tape deck, you can use this port to connect the Ensemble HD system to an external amplifier or other home audio system.

Note The 2CH OUT port is intended for use as a pass-through port. You cannot use the Ensemble HD system to control the volume of the audio signal transmitted through this port.

Setting Up the Remote Control After connecting a new component, you can continue to use its original remote control. However, it may be more convenient to set up the Ensemble HD remote control to work with it. That way, you only need to use one remote control.

You enable the Ensemble HD remote control to recognize the new component by entering a setup code as described on page 37. This creates the appropriate commands for your device in one of the remote control menus listed below:

Component Remote control menu name

Cable box CABLE

Satellite receiver SAT

High-definition DVD player HD

Digital video recorder (for example, TiVo) DVR

Video game console AUX

Video cassette recorder VIDEO

AUDIO 1 IN port2CH OUT port

37

Note The menus for the listed components remain blank until you enter the setup code for the component. The remote control also has several other menus (DVD, RADIO, AUDIO, and PROJ). These are used to operate the built-in components of the Ensemble HD system.

If you have a type of component not listed above, first enter its setup code as described in the next section. Then see Customizing the Remote Control Menu on page 39 for additional instructions.

Entering the Setup Code for Your Component

You enable the remote control to recognize the new component by entering a setup code from the tables starting on page 85. You may have to try out several codes before finding the right one for your component. Once the correct code is entered, the remote control will automatically create the appropriate commands in the menu for the new device.

If you cant find the correct code, you can teach the remote control how to operate your new component one function at a time, but this may take much longer (see page 72).

1 Turn on the component you want to set up. Each time you enter a code, the remote control will try to turn off your component by sending a power-off command. You will know that you have entered the correct code when the component turns off.

2 Press and hold both the MAIN and ENT (Enter) buttons for approximately three seconds to enter the SETUP menu.

Note You have 30 seconds to perform a step while you are in the SETUP menu. If you dont press a button, the remote control returns to the MAIN menu.

3 Select the P-PRO (Pre-Programmed) option on the LCD screen.

MAIN button

ENT button

SETUP

P-PRO

LEARN

EDIT

MACRO

FAV

1 OF 3

Select P-PRO

38

4 Choose the name of the remote control menu that will operate the device. Its important to choose the one whose name matches the device label you selected in the Source Assign screen on page 35. If you dont see your device on the screen, press the PAGE or (page up or down) button to view more options. Use the u or d button to highlight the desired option so it flashes, then press the SEL (Select) button.

Note Some of the device names (DVD, RADIO, AUDIO, and PROJ) are already used by the Ensemble HD system, and you cannot select them.

5 Use the u or d button to select the type of device youve connected, then press the SEL (Select) button. (The names in this step correspond to the categories of devices found in the code tables on page 36).

6 Point the remote control at the component, then enter the first three-digit code number from the code tables starting on page 87. The code numbers are listed by categories of devices, then by brand. After you enter a three-digit code, look at the component to see if it has turned off. (You do not have to press SEL or ENT to enter the code.)

Continue to enter code numbers until the component turns off.

Note If the component fails to turn off after you have entered all the code numbers listed for your brand, you can scan through the other brands in the table using the UP and DOWN options on the LCD screen (there is a chance that your component was actually manufactured by another brand). However, most of the code tables are large, so it is usually faster to use the learning method described on page 72.

7 When the component turns off, save the code number you entered by selecting the SAVE option on the LCD screen.

8 Press the MAIN button twice to exit the SETUP menu.

9 Test the Ensemble HD remote control to make sure it has all the functions you need for your component. When you select your components menu, you should see all the functions needed to operate it. If any commands are missing, you can copy them from the components original remote control (see page 72).

Note Refer to the manual that came with your component for instructions on using the commands to operate it.

SEL (Select) button

u button

d button

CABLE

089

UP

DOWN

SAVE

EXIT

PRESS

Scan to next (UP) or previous (DOWN) code number

Code number

39

Customizing the Remote Control Menu

For most components that can be connected to the Ensemble HD system, a full set of functions is already programmed into the remote control. These functions work with all the components listed in the tables starting on page 85. If youve connected a different type of component or want to customize the menu for your device, follow the steps below.

Note There are 10 devices listed in the remote controls MAIN menu. You cannot add new ones, but you can modify an existing one to customize it for your new component.

1 First enter the code for you component, as described on page 37. If you successfully enter the correct code, the remote control will automatically create the appropriate commands in the menu for the new device.

2 If desired, change the menu name for the new device on the remote control. For example, you might want to change AUX to HDTV. To change the device name, see Editing Device Names and Commands on page 75.

Note If you change the device name on the remote control, it will not match the name shown on the projection screen when you select your component for viewing.

3 If necessary, delete any functions currently displayed in the menu that you dont need. See Editing Device Names and Commands on page 75.

4 If any functions are missing, copy them from components original remote control. See Learning Commands from Another Remote Control on page 72.

Using the Remote Control to Operate Your Equipment When youre ready to use your new component, follow these steps to turn it on:

1 Make sure the Ensemble HD system is ready for use. If necessary, press the MAIN button on the remote control, then press the ON button to turn on the system. The screen comes down, and the projector and AV controller turn on.

2 Select the component you want to operate on the remote controls LCD screen (for example, CABLE or SAT).

Your component turns on and the AV controller switches to that component as its source.

MAIN

DVD

CABLE

SAT

HD

RADIO

1 OF 2

ON button MAIN button

40

Note When the menu is displayed for a component (not the MAIN menu), the ON and OFF buttons operate that component. When the MAIN menu is displayed, the ON and OFF buttons control the Ensemble HD system.

Refer to the manual that came with your component for instructions on using the commands to operate it.

3 When youre done using your component, make sure its menu screen is displayed on the remote control and press the OFF button.

4 To turn off the Ensemble HD system, press the MAIN button to return to the MAIN menu. Then press the OFF button to turn off the projector and AV controller, and to raise the screen.

41

Adjusting the Sound, Picture, and Other Settings

You can use the menu system described in this chapter to adjust the sound, picture, and other settings. See these sections:

Using the On-screen Menu System below

Adjusting the Picture on page 42

Adjusting the Sound on page 46

Using Other Features on page 49

Restoring Factory Defaults on page 51

Using the On-screen Menu System Follow these guidelines when using the on-screen menu system.

1 Make sure the MAIN menu is displayed on the remote control.

Note The MAIN menu must be displayed, or you wont be able to open the Ensemble HD menu by pressing the MENU button. If another components page is displayed instead, its menu screen will open when you press the MENU button.

2 Point the remote control at the screen and press the MENU button. You see the Ensemble HD menu, as shown below.

Note When you open the menu, it displays the last screen you used.

Move Enter ExitMenuSel

Video

Language

Preference

Audio

Reset

Voice

Bass

Treble

Surround

Front Distance

Center Distance

Rear Distance

Test Tone

0 dB

0 dB

0 dB

0 dB

5 ft.

5 ft.

5 ft.

Settings

Legend

Main options

42

3 Use the u or d button to highlight the menu you want to use (such as Audio or Video). Then press the SEL (Select) button to open it.

4 Use the u or d button to highlight the setting you want to adjust.

5 After highlighting the setting you want to adjust, check the legend at the bottom of the screen. It tells you which buttons let you adjust the setting.

For example, if you see a slider bar like this, use the l and r buttons to change the setting.

6 Press the ESC (Escape) button to return to the previous menu level, or press the MENU button to exit the menu system.

Adjusting the Picture

Adjusting the Color Mode

You can change the projectors Color Mode to automatically adjust brightness, contrast, and color, letting you quickly optimize the image for different lighting conditions. For example, you might select Living Room for watching movies in the daytime with the curtains closed, and Theatre for watching movies at night.

1 Make sure the MAIN menu is displayed on the remote control. If necessary, press the MAIN button.

2 Press the PAGE button to display the second page of components.

3 Select the PROJ option on the LCD screen to open the Projector menu.

4 Select COL-M (Color Mode). You see a screen like this:

5 Press the COL-M button repeatedly to change modes. (With the PowerLite Home Cinema 720, use the u or d button to highlight the setting you want to use.)

Color Mode Description

Dynamic For projecting the brightest picture available

Living Room For watching movies during the day

Natural For projecting the most natural, accurate colors

Theatre For viewing movies in a dark room

Arrow buttons

0 dB

[Color Mode]

Theatre Natural

Dynamic

Theatre Black 1 Theatre Black 2

Enter new PasswordLiving Room

Screen shown for the PowerLite Home Cinema 1080

43

6 Press the SEL (Select) button to apply the setting.

Adjusting the Aspect Ratio

Some picture sources, such as standard-definition TV broadcasts, are not formatted for high-definition video. To fit such images optimally onto the screen, you can change their shape (or aspect ratio) by pressing the ASP (Aspect) button on the remote control. Press the ASP button repeatedly to move through the settings. The setting you choose depends on how the original picture source is formatted.

Note No matter which aspect ratio setting you choose, the original image is automatically upscaled (resized) to fit on your Ensemble HD screen.

Normal 1 (default setting) for widescreen content, such as HD television broadcasts, presented in the 16:9 HDTV aspect ratio.

Note Movies released in a theatrical widescreen format (such as 1.85:1 or 2.35:1) will display with black bars at the top and bottom. Thats because high-definition TVs and home entertainment systems use the slightly narrower 16:9 (1.78:1) aspect ratio.

Normal 2 for use with DVDs that present movies in their original 1.85:1 aspect ratio. Eliminates narrow black bars at the top and bottom so the image fills the whole screen. Can also be used to improve the appearance of widescreen TV broadcasts that contain noise in the overscanned area.

Theatre Black 1 For images close to those produced by professionally used broadcast monitors

Theatre Black 2 For black-and-white movies or those with dark scenes

sRGB For projecting computer images that conform to the sRGB color standard (PowerLite Home Cinema 720 only)

Color Mode Description

ASP (Aspect) button

Original 16:9 image Normal 1 maintains the original aspect ratio

1.85:1 theatrical aspect ratio shown using Normal 1 setting

Normal 2 enlarges the image to eliminate the black bars, but cuts off some side content

44

4:3 for standard-definition TV broadcasts, video games, and other 4:3 content.

Wide for standard-definition TV broadcasts, video games, and other 4:3 content.

Zoom 1 for use with DVDs that present movies in their original 2.35:1 aspect ratio.

Zoom 2 for standard-definition (4:3) content that has been letterboxed to present movies in their original aspect ratio.

Note When youre viewing a particular source, you can press the OSD (On-Screen Display) button to display the selected aspect ratio.

4:3 image shown using Normal 1 setting 4:3 adds side bars to display the image in its original aspect ratio

4:3 image shown using 4:3 setting Wide keeps the center of the image close to its original proportions, while stretching the image more at the sides to fill the screen

2.35:1 theatrical aspect ratio shown using Normal 1 setting

Zoom 1 enlarges the image to eliminate the black bars, but cuts off some side content

Letterboxed 1.85:1 movie image shown using 4:3 setting

Zoom 2 enlarges the image to eliminate the black bars on the sides, but narrow bars remain at the top and bottom

45

Adjusting the Picture Quality

The settings described below control how the image is processed by the Ensemble HD systems AV controller. Before changing any of these settings, first be sure to select the best Color Mode as described on page 42.

Note These settings adjust the picture quality for all sources, not for each source independently.

To access the Video menu, make sure the MAIN menu is displayed on the remote control, press the MENU button, then select Video. You see this screen:

You can adjust the following settings:

Brightness Adjusts the brightness so its suitable for your viewing conditions.

Contrast Adjusts the contrast between the light and dark parts of the image.

Color Adjusts the color intensity of the image.

Tint Shifts the color balance between magenta and green.

Sharpness Use this function to make lines and edges appear more distinct.

Noise Reduction This function softens the image and reduces noise. Use only if you are receiving a weak signal.

HDMI Output Sets the output signal to either 720P (for the PowerLite Home Cinema 720) or 1080P (for the PowerLite Home Cinema 1080). Automatically defaults to the projectors resolution.

Source Assign Lets you combine audio and video sources connected to the AV controller through different ports. See Linking Audio and Video Sources on page 34 for details.

Video

Language

Preference

Audio

Reset

Brightness

Contrast

Color

Tint

Sharpness

Noise Reduction

HDMI Output

Source Assign

0

0

0

0

0

Medium

1080P

Move Enter ExitMenuSel

46

Adjusting the Sound To access the Audio menu, make sure the MAIN menu is displayed on the remote control, press the Menu button, then select Audio. You see this screen:

You can adjust the following settings:

Voice Lets you adjust the volume of the center channel, which is mainly used for actors voices in movies.

Bass Lets you adjust the volume at the lower end of the sound spectrum. This setting adjusts the bass sound from the left and right front channels and the subwoofer.

Treble Lets you adjust the volume at the higher end of the sound spectrum.

Surround Lets you adjust the volume from the rear (surround) speakers.

Front Distance Adjusts the sound delay from the left and right front speakers. Measure and enter the distance from your main seating location to the left and right speakers on the screen.

Center Distance Adjusts the sound delay from the front center speakers. Measure and enter the distance from your main viewing location to the speakers in the middle of the screen.

Rear Distance Adjusts the sound delay from the rear (surround) speakers. Measure and enter the distance from your main seating location to the rear speakers.

Test Tone Lets you check and adjust the sound level for each speaker. See the next section for details.

Note You can also adjust the Voice, Bass, Treble, and Surround settings by selecting the AUDIO menu on the remote control, and then selecting TONE. Press TONE repeatedly to select each setting.

Move Enter ExitMenuSel

Video

Language

Preference

Audio

Reset

Voice

Bass

Treble

Surround

Front Distance

Center Distance

Rear Distance

Test Tone

0 dB

0 dB

0 dB

0 dB

5 ft.

5 ft.

5 ft.

47

Using Test Tones to Adjust the Sound

Use the test tones to adjust the volume for each speaker independently or to verify that each speaker is working properly. Use a sound-level meter to ensure that the tone emitted from each speaker is 75 dB. If youre not using a meter, make sure all the speakers sound consistent in volume.

1 Make sure the MAIN menu is displayed on the remote control, press the MENU button, select Audio, then select Test Tone. You see this screen:

The speakers automatically begin emitting tones, one by one.

2 Use a sound-level meter to measure the volume from the usual seating area. Set the meter for C weight and slow response.

Use the u or d button to move the test tone to a different speaker. Press the u button as needed to keep the test tone from advancing to the next speaker.

3 Use the l or r button to change the speakers output. Make sure all the speakers output sound at 75 dB.

4 When youre done adjusting the settings, press the MENU button to exit the menu system.

Changing the Surround Sound Format

Depending on your audio source, you may be able to select from one or more surround sound formats.

1 Make sure the MAIN menu is displayed on the remote control, then select the AUDIO option.

2 Select the SURR (Surround) option to change the audio format. Each time you press SURR, the format changes to one of the following settings:

DPLII Movie or DPLII Music (Dolby Pro Logic II) for extracting 5.1-channel sound from recordings made with Dolby Surround technology. If the source is digitally encoded, you see the type of encodingDolby Digital or DTS (Digital Theatre Sound)displayed on the screen.

STEREO for digital and analog sources recorded in 2-channel stereo, when you dont want to hear it using any surround sound effects.

Note When youre viewing a particular source, you can press the OSD (On-Screen Display) button to display the current audio format.

Left Speaker

Center Speaker

Right Speaker

Rear Right Speaker

Rear Left Speaker

Subwoofer Speaker

0 dB

0 dB

0 dB

0 dB

0 dB

0 dB

Move Adjust ExitMenuESC Return

[ Te s t To n e ]

48

Using Midnight Mode

Midnight Mode adjusts the sound for late-night viewing when you want to avoid disturbing others. The volume is reduced at the bass end with volume highs and lows being compressed to a narrower range.

1 To access the Midnight Mode setting, make sure the MAIN menu is displayed on the remote control, press the Menu button, then select Preference. You see this screen:

2 Select Midnight Mode, then select Off, Medium, or Full.

Video

Language

Preference

Audio

Reset

Midnight Mode

Closed Caption

Parental Control

Off

Off

Move Enter ExitMenuSel

49

Using Other Features In addition to its audio and video settings, the on-screen menu system lets you select language options, turn on closed captioning, and use parental controls to restrict access to rated DVDs.

Choosing the Language

You can change the language that the on-screen display and various DVD features appear in. For each option, you can choose from English, French, or Spanish.

To access the Language menu, make sure the MAIN menu is displayed on the remote control, press the Menu button, then select Language. You see this screen:

You can adjust the following settings:

On Screen Display Lets you change the language for the menu screens discussed and shown in this chapter.

DVD Menu Lets you select the default language for the menu you see when you first insert a DVD (the menu that lets you select its contents).

DVD Audio Lets you select the default language for the audio portion of your DVDs, when you play a DVD that has separate audio tracks in different languages. DVDs with separate audio tracks have a symbol like this to indicate the number of languages:

DVD Subtitles Lets you select the default language that subtitles appear in, when you turn on the subtitles option for a DVD that has subtitles. DVDs with subtitles have a symbol like this to indicate the number of subtitled languages:

Video

Language

Preference

Audio

Reset

On Screen Display

DVD Menu

DVD Audio

DVD Subtitles

English

English

English

English

Move Enter ExitMenuSel

50

Using Parental Controls

You can control access to rated DVDs to prevent children from viewing unsuitable content. To set up parental controls, youll need to create a 4-digit numeric password.

Note The parental controls cannot be used to prevent viewing of unrated DVDs.

To set up parental controls, follow these steps:

1 Make sure the MAIN menu is displayed on the remote control. Press the Menu button, select Preference, then select Parental Control. You see this screen:

2 Select the DVD option on the remote control. (You must be in DVD mode to use the numeric keypad, as required in step 3.)

3 Enter your parental controls password. If this is your first time using the parental controls, enter the default password 1234.

You see this screen:

4 If this is your first time using the parental controls, select Enter new Password. Use the numeric keypad on the remote control to create a 4-digit numeric password. Confirm the password by re-entering it on the next screen.

Note Be sure to write down the password and keep it in a safe place. Youll need the password if you want to change the parental control settings in the future.

0 - 9 Number ExitMenu

[Parental Control]

Enter Password

- - - -

ESC Return

[Parental Control] Enter new Password

Max. allowable rating None

Return to Preference menu

ExitMenuEnterSelMove

new Password

ESC Return

51

5 Select Max. allowable rating and select the highest rating you want to allow for viewing.

6 When youre done changing the settings, press the MENU button to exit the menu system.

Restoring Factory Defaults If you customize the picture and sound but dont find your changes satisfactory, you can restore the system to its original settings. You should use this function only if necessary, because it may restore a number of settings youd like to keep.

Caution When you restore the settings, the audio, video, language, and source assign settings are returned to their original state.

1 Make sure the MAIN menu is displayed on the remote control, press the MENU button, then select Reset. You see this screen:

2 Press Sel (Select) to return to the factory default settings, or press the Menu button to cancel.

3 At the confirmation screen, select Yes. The AV controller restores its settings and shuts itself down.

Note You can also restore the remote control to its original settings. See Restoring Remote Control Factory Defaults on page 83.

Rating Description

G General audience

PG Parental guidance suggested

PG13 Parents strongly cautioned

R Restricted No one under 17 admitted without a parent or adult guardian

NC17 No one under 17 admitted

None No rating selected

Video

Language

Preference

Audio

Reset

Reset System to Factory Default

Move Enter ExitMenuSelESC Return

52

53

Cleaning and Maintenance

Follow the instructions in this chapter when your Ensemble HD system needs ordinary cleaning, as described below. Routine maintenance is not required. However, you may need to perform the following basic tasks on occasion:

Adjusting the Screen Length on page 54

Adjusting the Image Position and Focus on page 56

Checking the Projector Lamp on page 58

Replacing Remote Control Batteries on page 59

Warning Never open the cover on the projector or other components. Dangerous electrical voltages can injure you severely. Do not try to service this product yourself, except as specifically explained in this Users Guide.

Cleaning Warning Before you clean any part of the system, turn the system off and unplug the power cord.

Cleaning the Screen

If the screen gets soiled, clean it using a clean, white, 100% cotton cloth. Dampen the cloth with clean, clear water (do not use detergents). Gently wipe the soiled area in one direction only. Do not use a circular motion. Wipe any moisture from the screen using a dry cotton cloth.

A lint roller or masking tape may be used to remove loose dust or lint.

Cleaning the Projector Lens

Clean the lens if you notice dirt or dust on the surface. To remove dirt or smears, use lens-cleaning tissue. If necessary, moisten a soft cloth with lens cleaner and gently wipe the lens surface.

Caution Clean the lens gently to avoid changing the focus or misaligning the image with the screen. If this happens, see Adjusting the Image Position and Focus on page 56.

54

Cleaning System Components

You can clean the outside of the system components to remove dust and fingerprints. Before cleaning, turn off the system and unplug the power cord.

To remove dirt or dust, wipe the component with a soft, dry, lint-free cloth.

To remove stubborn dirt or stains, moisten a soft cloth with water and a neutral detergent. Then wipe the component and dry it with a dry cloth.

Caution Never use wax, alcohol, benzene, thinner, or other chemical detergents. These can damage components.

Adjusting the Screen Length You can adjust how far the screen comes down when you open it. The screen is factory-set to come down 55 inches, but you can set it to come down as far as 64 inches, with a 12-inch black drop at the top.

Note If you change the position of the screen, youll have to reposition the image. See page 56 for instructions.

1 Make sure the MAIN menu is displayed on the remote control. If necessary, press the MAIN button.

2 Press the PAGE button to display additional components.

3 Press the button to the right of PROJ to select the projector menu.

4 Use the following commands to raise and lower the screen, and to stop it at the desired position:

S-UP to raise the screen

S-DWN to lower the screen

When the screen comes to a stop, press S-DWN again to lower it beyond the current stop-position. You can bring it down as far as the maximum length set by the adjustment screw described in Manual Screen Adjustment on page 55.

S-STP to stop the screen

5 Once the screen is positioned where you want it, press S-SET to set the screen position.

55 inches 64 inches

55

6 Press S-UP to raise the screen fully.

Note You must raise the screen all the way for the new position to take effect.

7 Press S-DWN re-open the screen. Verify that it comes down and stops at the desired position.

Manual Screen Adjustment

If you werent able to adjust the screen length precisely enough using the remote control, you can adjust it using the 4-mm Allen wrench that came with your system. This adjustment sets the maximum length that the screen can come down.

Caution Do not allow the screen to descend more than 64 inches (with a black drop of more than 12 inches), or the fabric could separate from the roller.

1 After adjusting the screen length as described in the previous section, press S-DWN on the remote control to lower the screen fully.

2 Locate the lower-limit adjustment screw on the left side of the screen roller, inside the screen casing.

Caution Do not turn the upper-limit adjustment screw, located to the rear of the lower-limit adjustment screw.

3 Use a 4-mm Allen wrench to rotate the adjustment screw:

To raise the screen: Turn the screw clockwise.

To lower the screen: Turn the screw counterclockwise.

Each turn changes the screens stop-position by two-thirds of an inch. However, since the screen doesnt move as you adjust it, youll need to estimate how far to turn the screw. After turning the screw the estimated number of turns, remove the Allen wrench and press S-UP on the remote control to raise the screen fully. Then press S-DWN to re-open the screen. Verify that it comes down and stops at the desired position.

4-mm Allen wrench

56

Adjusting the Image Position and Focus If you adjusted how far the screen comes down (see page 54), youll need to reposition the image on the screen as described below. You may also need to reposition or refocus the image if you cleaned the lens and accidentally changed it from its original position.

Repositioning the Image

1 Remove the cover on the bottom of the projector enclosure to access the lens shift dials on the projector. Slide the cover straight forward, then remove it. (The cover is held in place with clips, which may be tight.)

2 If desired, you can display a test pattern to help adjust the image position. Youll need to use the remote control that came with the projector (not the Ensemble HD remote). Press the Pattern button on the remote control to display the pattern. Press the Pattern button again to turn it off.

Pattern button

57

3 Use the horizontal lens shift dial to move the image left or right. Use the vertical lens shift dial to move the image up or down.

Note Do not try to move the lens by hand, or you may damage the projector. Always use the lens shift dials to change the image position. If a lens shift dial becomes hard to turn, you cannot adjust the position any further.

4 When youre done adjusting the image position, replace the cover on the bottom of the projector enclosure.

Focusing and Resizing the Image

Use the focus ring to sharpen the image, or the zoom ring to resize it.

Up/down adjustment Left/right adjustment

ZoomFocus

58

Checking the Projector Lamp The projector lamp lasts for up to 3000 hours. You can use the Info menu to check how long its been in use (see below). Its time to replace the lamp when:

The projected image gets darker or starts to deteriorate.

The message Replace the lamp appears on the screen when you start projecting.

The projectors warning light flashes red at half-second intervals (see below for details).

Note Lamp life results will vary depending on mode selected, environmental conditions, and usage. Turn off this product when not in use to prolong the life of the projector.

Checking the Info Menu

If you have access to the remote control that came with the projector (not the Ensemble HD remote), you can use it to check the projectors Info menu to find out how long the lamp has been in use. If you dont have the remote control, youll need to remove the cover on the bottom of the projector enclosure (see page 56) and then use the buttons on the projectors control panel to display the Info menu.

1 Press the Menu button on the projectors remote control or on its control panel.

2 Use the menu navigation buttons to open the Info menu.

3 Check the Lamp Hours to determine how long the lamp has been in use.

Note The Lamp Hours shows 0H until youve used the lamp for at least 10 hours.

Checking the Warning Light

If you suspect that the lamp needs to be replaced, check the warning light on the projectors control panel.

1 Remove the cover on the bottom of the projector enclosure (see page 56).

2 Check the warning light, pictured below.

If the warning light is flashing red at half-second intervals, the lamp needs to be replaced. Contact your dealer or a qualified servicer, or contact Epson for help (see page 69).

Warning light

59

Replacing Remote Control Batteries If the Ensemble HD remote control isnt working correctly, check the following:

Aim the remote control at the top of the screen and try operating the screen. If the remote control works only when you aim it at the top of the screen but not elsewhere in the room, you may need to replace the batteries.

Press the LIGHT button on the side of the remote control and verify its screen and buttons light up. (You need to be in a darkened room to see this.) If they dont light up, replace the batteries.

Check for a LOW BATTERY message at the bottom of the remote controls LCD screen.

Follow the steps below to replace the batteries in the remote control.

Note All user-made settings are stored in non-volatile memory and are preserved when the batteries are taken out.

1 Remove the battery compartment cover on the back of the remote control.

2 Insert 4 AAA batteries as shown below.

3 Replace the cover.

60

61

Solving Problems

If youre having a problem with the Ensemble HD system, check for a solution in one of these sections:

Basic Operation Problems below

Picture Problems on page 62

Sound Problems on page 64

Problems Using the Screen on page 65

Problems Using the Remote Control on page 66

Problems Using the DVD Player on page 67

Problems Using the Radio on page 67

Problems Using an External Component on page 68

If you cannot solve the problem on your own, contact Epson for help (see page 69).

Basic Operation Problems

Problem Solution

The system doesnt turn on. Make sure the MAIN menu is displayed on the remote control, then press the ON button to turn the system on or the OFF button to turn the system off. The remote controls batteries may need to be replaced. See page 59. Check the blue light at the top of the screen. When the screen is raised, the light remains on. This indicates that the system is receiving power. If the light is not on, make sure your electrical outlet is working and isnt controlled by a wall switch or timer. Check that the power cords on the back of the subwoofer are connected securely. Check the power switches on the back of the subwoofer. Make sure the PWR ON MODE switch is in the AUTO position and the MASTER POWER switch is turned on.

The projector doesnt turn on. Press the MAIN button on the remote control, then press the ON button. Keep the remote control pointed at the screen for several seconds after you press the button to ensure that the projector turns on. Try to turn on the projector by itself. Open the PROJ menu on the remote control, then press the ON button. The lamp may need to be replaced. See Checking the Projector Lamp on page 58.

62

Picture Problems

The AV controller doesnt turn on. Make sure the AV controller is receiving power. When its in standby mode, the light around the ON/STANDBY button is orange. If the light is off, the unit is not receiving power. Check the power cord to make sure its securely connected to the subwoofer or a working electrical outlet. Press the ON/STANDBY button to turn on the AV controller. The light around the button turns blue when the unit is on. Try to turn on the AV controller using the remote control. Make sure the MAIN menu is displayed on the remote control (if necessary, press the MAIN button). Then either press the ON button, or select the DVD or RADIO option. If the AV controller does not turn on, replace the remote controls batteries (see page 59). Make sure the control cable is connected to the IR IN port on the back of the AV controller.

The screen cant be raised or lowered.

See Problems Using the Screen on page 65.

There is no sound. See Sound Problems on page 64.

Problem Solution

You dont see a picture. Make sure the projector is turned on. Press the MAIN button on the remote control, then press the ON button. Keep the remote control pointed at the screen for several seconds after you press the button to ensure that the projector turns on. If youre sourcing video from an external component, make sure that component is turned on. The lamp may need to be replaced. See Checking the Projector Lamp on page 58. Make sure the video cable is connected to the HDMI OUT port on the back of the AV controller. If youve connected an external component, check for loose or disconnected cables on the back of the component and the AV controller. If youve connected an external component, check the Source Assign screen. Make sure the correct label is assigned to the video port to which the component is connected (see page 34).

You see light or dark pixels on the screen.

The projectors display is more than 99.99% accurate. However, some individual pixels (dots) may appear light or dark due to the inherent limitations of LCD manufacturing technology.

You notice smudges or dirt in the image.

You may need to clean the screen (see page 53) or the projector lens (see page 53).

The image sometimes gets scrambled or broken up.

Use a soft, lint-free cloth to clean the disk. Wipe gently in a straight line from the center of the disc toward the outside. If necessary, moisten the cloth with water, mild detergent, or rubbing alcohol. Avoid using abrasives, solvents, or other cleansers.

You see scrolling horizontal bars in the picture (hum bars) when watching satellite or cable TV, or you hear a buzzing sound.

Connect a ground loop isolator to the satellite or CATV cable close to where it connects to your equipment. You can purchase this module from electronics retailers. The module filters out interference caused by your cable or satellite systems outdoor ground connection. Or you can use a coaxial surge protector. WARNING: Never disconnect the cables ground connection or disable the grounding pins on your power cords. These exist for the protection of both you and your equipment.

Problem Solution

63

The image is too soft or out of focus.

If you cleaned the lens, you may have accidentally changed the position of the focus ring. See Adjusting the Image Position and Focus on page 56. Adjust the sharpness of the image using the Sharpness settings (see Adjusting the Picture on page 42). Be careful not to over-adjust the sharpness, or you may get banding in some images.

The image isnt positioned correctly on the screen.

If the image isnt at the right height, you may need to adjust how far the screen comes down. See Adjusting the Screen Length on page 54. If you cleaned the lens, you may have accidentally changed the lens position or the position of the zoom ring. See Adjusting the Image Position and Focus on page 56.

The image is cut off, squeezed in one direction, or stretched out.

Press the ASP (Aspect) button on the remote control to select a different aspect ratio setting. See Adjusting the Aspect Ratio on page 43. If youve connected a second DVD player as an external component, make sure its set to output a widescreen 16:9 image.

There are black bars at the top and bottom of the image.

Press the ASP (Aspect) button on the remote control to select a different aspect ratio setting. See Adjusting the Aspect Ratio on page 43. If youre watching a movie released in a theatrical widescreen format (such as 1.85:1 or 2.35:1), you must display it with black bars at the top and bottom if you want to see the whole image. Thats because high-definition TVs and home entertainment systems use the slightly narrower 16:9 (1.78:1) aspect ratio.

The image is too dark. Make sure youve selected the best Color Mode for your viewing environment. See Adjusting the Color Mode on page 42. After setting the Color Mode, you may need to fine-tune the brightness and contrast. See Adjusting the Picture Quality on page 45. If the projector lamp is old, you may need to replace it. See Checking the Projector Lamp on page 58.

The colors dont look right. Make sure youve selected the best Color Mode for your viewing environment. See Adjusting the Color Mode on page 42. After setting the Color Mode, you may need to fine-tune the color settings. See Adjusting the Picture Quality on page 45. If youve changed several settings and the picture still doesnt look right, you can return all the settings to their original state. However, this option should be used only if necessary. See Restoring Factory Defaults on page 51.

Problem Solution

64

Sound Problems

Problem Solution

There is no sound. Check the power switches on the back of the subwoofer. Make sure the PWR ON MODE switch is in the AUTO position and the MASTER POWER switch is turned on. Press the MUTE button on the remote control to make sure the sound wasnt muted or turned off. Unplug any headphones that may be plugged into the AV controller. Try increasing the volume. Depending on your audio source, its possible that no sound may be heard at the low end of the +dB range. If youve connected an external audio device such as an MP3 player, make sure its volume control is adjusted to allow sound output. If youve connected an external audio device such as an MP3 player or tape deck, be sure to select the correct audio port: Select the AUDIO option on the remote control, then select either AUD1 (for the Audio 1 port in back of the AV controller) or AUD2 (for the Audio 2 port in front). If youve connected an external component, check the Source Assign screen. Make sure the selected Audio Input matches the port to which the audio is connected (see page 34). If youve connected an external video component using an HDMI cable, make sure HDMI audio is enabled in the components setup menu. If your component doesnt support HDMI audio, you may need to connect a coaxial or optical cable to carry the audio signal (see page 33). Check for loose or disconnected cables on the back of the subwoofer and AV controller.

The high and low parts of the sound spectrum seem weak.

Make sure Midnight Mode isnt turned on. See Using Midnight Mode on page 48.

Bass tones arent loud enough. Use the Bass setting to increase the bass. See Adjusting the Sound on page 46. Use the Test Tones function to increase the output of the subwoofer. See Using Test Tones to Adjust the Sound on page 47. If you rearranged your room or moved your subwoofer to a different location, try switching the PHASE control on the back of the subwoofer.

65

Problems Using the Screen

Problem Solution

You cannot lower the screen. Check for a blue light at the top of the screen. The light indicates that the screen is receiving power. If the light is off, make sure the power cords on the back of the subwoofer are connected securely. Select the PROJ (Projector) option on the remote control, then select S-DWN to lower the screen. The screen may be stuck in the closed position. Grasp the weighted bar that hangs from the bottom of the screen and pull it slightly to free it. Then try opening the screen again with the remote control. The screen motor may have overheated if you repeatedly raised and lowered the screen. Let the motor cool for 5 to 10 minutes, then try operating the screen again. Check for problems with the remote control (see page 66).

You cannot raise the screen. Check that the blue light at the top of the screen flashes when you make a selection with the remote control. The light indicates that the screen is receiving power. If the light does not flash, make sure the power cords on the back of the subwoofer are connected securely. Select the PROJ (Projector) option on the remote control, then select S-UP to raise the screen. The screen motor may have overheated if you repeatedly raised and lowered the screen. Let the motor cool for 5 to 10 minutes, then try operating the screen again. Check for problems with the remote control (see page 66).

The screen comes down too far, or not far enough.

The screen can be adjusted so it comes down anywhere from 55 to 64 inches. If the setting was inadvertently changed, see Controlling the Screen on page 15 to reset it.

The image isnt positioned correctly on the screen.

You may need to adjust how far the screen comes down. See Adjusting the Screen Length on page 54. If you cleaned the lens, you may have accidentally changed the lens position or the position of the zoom ring. See Adjusting the Image Position and Focus on page 56.

Blue light (remote control sensor)

66

Problems Using the Remote Control

Problem Solution

The system doesnt respond to the remote control.

Make sure youre within about 20 feet of the screen. Point the remote control toward the sensor at the top of the screen. You may need to replace the remote controls batteries (see page 59). If you suspect they are weak, press the LIGHT button on the side of the remote control and verify its screen and buttons light up. (You need to be in a darkened room to see this.) If they dont light up, replace the batteries. Turn off any fluorescent lights. Make sure the screen is not in direct sunlight. Turn off nearby equipment that emits infrared energy, such as a radiant room heater. If you changed any of the remote controls RF settings (see page 81), make sure you didnt disable the remote controls IR LED.

The ON and OFF buttons dont operate the system.

Press the MAIN button first, then press either ON or OFF. Keep the remote control pointed at the screen for several seconds after you press the button to ensure that all the components in the system turn on or off.

When the numeric keypad is used, there is a delay before your selection is transmitted.

After entering digits with the keypad, press the SEL (Select) button to transmit your selection right away. If you dont press SEL, the selection will be transmitted after a brief delay.

The ENT (Enter) button doesnt work with the numeric keypad.

The ENT (Enter) button is meant for use with other components that may require it, such as cable box. Use the SEL (Select) button with the numeric keypad when operating the Ensemble HD system.

You want to return to the main menu of the DVD youre watching to select its contents.

Press the MENU or GUIDE button to display the main menu of a DVD. (The MENU button displays the Ensemble HD setup menu if the MAIN menu is displayed on the remote control. If a different menu is displayed, such as CABLE or SAT, it displays the menu system for that component.)

You want to view information about the selected audio or video source.

Press the OSD (On-Screen Display) button on the remote control.

You want to view chapter information for the DVD youre watching, or check the amount of time remaining.

Press the INFO button on the remote control.

You tried using advanced remote control setup features, and now the remote control doesnt work correctly.

You can restore the remote controls original settings. See Restoring Remote Control Factory Defaults on page 83.

The remote control has been lost or damaged.

Contact Epson for help (see page 69).

67

Problems Using the DVD Player

Problems Using the Radio

Problem Solution

The DVD/CD tray doesnt open or close.

Make sure a flash drive isnt inserted into the USB slot. The flash drive takes precedence over the operation of the DVD player. When a flash drive is inserted, the DVD player cannot be used and a disc cannot be inserted or ejected.

You want to view chapter information for the DVD youre watching, or check the amount of time remaining.

Press the INFO button on the remote control.

The display shows the amount of time remaining instead of the elapsed time for a DVD chapter, CD track, or MP3 audio file.

Press the INFO button on the remote control to select the desired display format, or to turn off the on-screen display.

You want to return to the main menu of the DVD youre watching to select its contents.

Press the MENU or GUIDE button to display the main menu of a DVD. (The MENU button displays the Ensemble HD setup menu if the MAIN menu is displayed on the remote control. If a different menu is displayed, such as CABLE or SAT, it displays the menu system for that component.)

Problem Solution

You get poor radio reception. The antennas included with the AV controller are sufficient to receive strong, local stations. To receive weaker stations, connect an antenna designed for stronger reception, such an outdoor antenna. See your antennas manual or the Ensemble HD Installation Guide to make connections for proper grounding protection.

You installed an outdoor antenna and properly grounded it, but you get audio hum or buzz as a result.

Connect a ground loop isolator to the coaxial antenna cable close to where it connects to the AV controller. You can purchase this module from electronics retailers. The module filters out interference caused by the outdoor ground connection. Or you can use a coaxial surge protector. WARNING: Never disconnect the antennas ground connection or disable the grounding pins on your power cords. These exist for the projection of both you and your equipment.

68

Problems Using an External Component

Problem Solution

Youve connected a new component, but cant operate it with the remote control.

You have to enter the setup code for your new component. See Setting Up the Remote Control on page 36.

Youve connected a DVD player and the image is elongated or has prominent black bars at the top and bottom.

Make sure the DVD players monitor type setting (or similarly named function) is set to output a widescreen 16:9 image.

Youve connected a new component, but youre not getting audio and/or video when you select the device with the remote control.

You need to match up the device name with the ports to which youve connected the audio and video. See Linking Audio and Video Sources on page 34.

Youve connected a type of device not included in the remote controls menu system, such as an HDTV tuner or DVD recorder.

See Customizing the Remote Control Menu on page 39.

You want to add a new device to the 10 devices already included in the remote controls menu system.

The remote control supports up to 10 devices, which are already programmed into it. Therefore, you cannot add a new device, but you can modify an existing one to customize it for your new component. See Customizing the Remote Control Menu on page 39.

Youve changed the name of a device listed on the remote control, but now when you select it, the name shown on the projection screen doesnt match the name shown on the remote control.

You can change the device name on the remote control, but it will no longer match the name shown on the projection screen when you select the device for viewing.

69

Where To Get Help

Internet Support

Visit Epsons support website at epson.com/support and select your product for solutions to common problems. You can download documentation, get FAQs and troubleshooting advice, or e-mail Epson with your questions.

Speak to a Support Representative

To use the Epson PrivateLine Support service, call (800) 637-7661 and enter the PIN on the Epson PrivateLine Support card that came with your projector. This is the fastest way of speaking to a live representative, and its free. This service is available 6 AM to 6 PM, Pacific Time, Monday through Friday, for the duration of your warranty period.

You may also speak with a projector support specialist by dialing (562) 276-4394, 6 AM to 6 PM, Pacific Time, Monday through Friday.

Days and hours of support are subject to change without notice. Toll or long distance charges may apply.

Before you call Epson for support, please have the following information ready:

Product name (Ensemble HD home cinema system)

Product serial number (located on the back of the weighted bar at the bottom of the screen, on the right side of the screen as viewed from the front)

Proof of purchase (such as a store receipt) and date of purchase

Description of the problem

Purchase Supplies and Accessories

You can purchase genuine Epson supplies and accessories from an Epson authorized reseller. To find the nearest reseller, call 800-GO-EPSON (800-463-7766). Or you can purchase online at www.EnsembleHD.com (U.S. sales only).

70

71

Using Advanced Remote Control Features

The features described in this chapter let you customize the behavior of the remote control. In most cases, you wont have to perform any of these customizationsfor example, if you want to set up the remote control to work with a new component, you only have to enter its setup code as described on page 37. This chapter is mainly for users who want to take full advantage of their remote controls advanced settings.

See these sections:

Adjusting the LCD Screen (below)

Learning Commands from Another Remote Control on page 72

Advanced Remote Control Setup on page 75

Using an RF Base Station on page 81

Restoring Remote Control Factory Defaults on page 83

Adjusting the LCD Screen You can adjust the amount of time the LCD screens backlight stays on when you press the LIGHT button on the side of the remote control. You can also adjust the screens contrast (see page 72).

1 Enter Setup mode by pressing and holding both the MAIN and ENT buttons for three seconds. The top of the screen displays SETUP.

2 Press the PAGE (page down) button to view more options.

3 Select the LIGHT option.

4 Do one of the following:

Enter the amount of time you would like the light to stay on using the numbered keypad (0-99 seconds).

If youd rather not have the backlight come on at all (this extends battery life), select the ON option: ON changes to OFF.

5 Select the SAVE option to save your settings.

6 Press the MAIN button to return to normal operation.

SETUP

PUNCH

ERASE

RECAL

LIGHT

CLONE

2 OF 3

Select LIGHT

72

Adjusting the Contrast

You can make the text on the remote controls LCD screen appear darker or lighter by adjusting the contrast.

To darken the text, press and hold both the MAIN and u buttons at the same time.

To lighten the text, press and hold both the MAIN and d buttons at the same time.

Learning Commands from Another Remote Control The Ensemble HD remote control can learn commands from another remote control, one button at a time. You may need to use this procedure if you werent successful in programming the remote control with a three- digit device code as described on page 37.

Note If you have two Ensemble HD remote controls and have customized one of them, you can copy your changes from one to the other. See Cloning Your Remote Control on page 74.

1 First choose names for any new commands, and add them to the appropriate menu for your device on the Ensemble HD remote control (see Editing Device Names and Commands on page 75).

2 Line-up the remote controls, head to head, one or two inches apart.

Contrast set low Contrast set high

u button

d button

MAIN button

73

3 On the Ensemble HD remote control, press and hold both the MAIN and ENT buttons for approximately three seconds. The top of the screen displays SETUP.

Note You have 30 seconds to complete each step. After that, the remote control returns to normal operation.

4 Select the LEARN option.

The top of the screen changes to LEARN and the screen lists several devices.

5 Select the device you would like to teach a command to by pressing the button to its right. If you dont see the device you want, press the PAGE or (page up or down) button to view more options.

6 On the Ensemble HD remote control, press any button you want to teach a command to. It can be either a physical button on the remote control or a command displayed on the menu screen.

Note If you dont see a command on the screen for the function you want to teach, press the PAGE or button to display more options. You can also add or edit text for a new command (see Editing Device Names and Commands on page 75). The only buttons you cant teach are the PAGE, MAIN, and ASP buttons.

Once you press a button, the top of the screen changes from LEARN to READY:

SETUP

P-PRO

LEARN

EDIT

MACRO

FAV

1 OF 3

Select LEARN

LEARN

DVD

CABLE

SAT

HD

RADIO

SELECT

Select the device you want to teach

READY

74

7 Press and hold the button for the corresponding function on your old remote control until the screen changes to either GOOD or FAILD (failed).

If GOOD appears at the top of the screen, you were successful. Continue by pressing the next button you want to teach. Repeat steps 6 and 7 until you have programmed all the buttons you want.

If FAILD appears, try to teach the same button again by repeating steps 6 and 7. If you continue having difficulties, try the following:

Move to another room. Plasma TVs, sunlight, and halogen or quartz lighting can interfere with the learning process.

Although the old remote control seems to work fine, its batteries may be old. Use fresh batteries.

Vary the distance between the remote controls gradually. Try 1/4 inch, 1 inch, 2 inches, and so on, up to 4 feet.

Repeatedly press the button on the old remote control instead of pressing and holding it during the learning process.

8 Once youve finished, press the MAIN button to return to normal operation.

Cloning Your Remote Control

If you have two Ensemble HD remote controls and have customized one of them, you can copy your changes from one to the other.

1 On each remote control, press and hold both the MAIN and ENT buttons for approximately three seconds. The top of the screen displays SETUP.

Note You have 30 seconds to complete each step. After that, the remote control returns to normal operation.

2 Select the CLONE option.

3 Line up the remote controls, head to head, one or two inches apart.

4 On the remote control you want to modify, select RECV (Receive). On the remote control whose settings you want to keep, select SEND.

5 Select START on each remote control to begin cloning.

Note Cloning can take several minutes to complete. You see GOOD displayed when the process is finished.

6 Once cloning is finished, press the MAIN button to return to normal operation.

GOOD FAILD

75

Advanced Remote Control Setup You can change the behavior of your remote control by editing device names (menu screen titles), editing command names, creating macros, adding or hiding menu pages, and setting up punch through commands (rarely used). See these sections:

Editing Device Names and Commands below

Setting Up Macros on page 77

Adding or Hiding Pages on page 78

Erasing Learned Buttons and Macros on page 79

Using Remote Control Punch-Through on page 80

Editing Device Names and Commands

Each type of device (DVD, CABLE, etc.) has its own menu with commands listed on multiple pages. You can customize the name of the device (which is also the name of the menu) or any command listed in the menu. If you are adding a new command from another remote control (see page 72) or creating a macro (see page 77), youll first need to add the command name to a blank space in the menu, as described below. If there isnt a space already, youll need to add a blank page (see Adding or Hiding Pages on page 78).

1 Press and hold both the MAIN and ENT buttons for approximately three seconds. The top of the screen displays SETUP.

Note You have 30 seconds to complete each step. After that, the remote control returns to normal operation.

2 Select the EDIT option.

The top of the screen changes to EDIT:

3 Select the TEXT option.

Note The PAGE option is for hiding or adding pages. See Adding or Hiding Pages on page 78.

SETUP

P-PRO

LEARN

EDIT

MACRO

FAV

1 OF 3

Select EDIT

EDIT

TEXT

PAGE

EXIT

Select TEXT

76

The top of screen displays EDIT, as shown at right, and you see a list of devices (DVD, CABLE, SAT, etc.).

4 Do one of the following:

To edit an existing command, select the device that has the command in its menu that you want to edit, then select the command. If necessary, press the PAGE button to display the second page of devices.

Note If you cant open a device menu, continue pressing PAGE until the top of the screen displays EDIT and you see the device name you want.

To add a command to a blank row, first select the device that has the blank row in its menu that you want to edit, as described above. Then press the PAGE button until the last page of commands is displayed with the blank row where you want to add text. Press the button to the right of that row.

Note If there are no blank rows, you can add a new blank page as described in Adding or Hiding Pages on page 78.

To edit a device name, press the PAGE button until the top of the screen displays MAIN and you see the page that has the name of the device you want to edit, then select the device.

The cursor flashes at the first character point in the line of text:

5 Use the l or r button to change the cursor position.

To delete a character, press d. To delete all characters, press u.

EDIT

DVD

CABLE

SAT

HD

RADIO

1 OF 2

DVD

MENU

AUDIO

EJECT

ANGLE

A<>B

Flashing cursor

77

Use the numeric keypad to enter characters in the same way as you send text-messages with many cell phones. Each time you press a button, it selects a different character represented by that button, as shown below:

6 When you have finished editing the line of text, press the button to its right. You see SAVED displayed at the bottom of the screen.

7 To edit any other commands for the same device, select the command and repeat steps 5 and 6.

8 When youve finished making edits, press the MAIN button several times to return to normal operation.

Setting Up Macros

A macro lets you perform several operations in sequence automatically. For example, when you press the ON button to turn on the Ensemble HD system, the remote control turns on the projector, turns on the AV controller, and lowers the screenall with one press of a button.

If you find there are other operations you sometimes perform togetherfor example, turning on your cable box and DVRyou can create a macro to perform the operations automatically. You store the macro by saving it as a menu option for a particular device (for example, you could create a macro called SYS ON in the DVR menu).

Note You cannot use any of the physical buttons on the remote control to store a macro.

1 Choose a name for the new macro and add it to the desired menu (see Editing Device Names and Commands on page 75).

2 Press and hold both the MAIN and ENT buttons for approximately three seconds. The top of the screen displays SETUP.

Note You have 30 seconds to complete each step. After that, the remote control returns to normal operation.

3 Select the MACRO option.

4 Navigate through the menu pages to the newly created menu item you want to turn into a macro, and press the button to its right.

The bottom of the screen flashes Step 0.

DEF2

Symbols

GHI3

PQR6

YZ9

JKL4

STU7

MNO5

ABC1

VWX8

78

5 Press the sequence of buttons for all the steps you want the macro to perform. Each time you press a button, the bottom of the screen flashes Step 1, Step 2, etc. Your macro can hold up to 190 steps.

Note You can program delays into the macro by pressing the pause button. Each time you press the pause button, it adds a one-half second delay.

6 When youre done entering all the steps of the macro, press the LIGHT button on the side of the remote control.

You see this screen:

7 Select one of the following:

SAVE to save the macro

UNDO to erase the last step of the macro and continue programming it

EXIT to erase the whole macro and return to step 4 on page 77

8 When youve finished, press the MAIN button several times to return to normal operation.

Adding or Hiding Pages

Each device menu (DVD, CABLE, etc.) has eight pages or screens. The commands that are visible in each menu occupy only a few of the pages, with the remaining pages being hidden. If necessary, you can add new pages (to make them visible), or hide existing ones. You may also need to add a page in order to create space for a new command or macro.

1 Press and hold both the MAIN and ENT buttons for approximately three seconds. The top of the screen displays SETUP.

Note You have 30 seconds to complete each step. After that, the remote control returns to normal operation.

2 Select the EDIT option.

MACRO

SAVE

UNDO

EXIT

SETUP

P-PRO

LEARN

EDIT

MACRO

FAV

1 OF 3

Select EDIT

79

The top of the screen changes to EDIT:

3 Select the PAGE option.

Note The TEXT option is for editing device names and commands. See Editing Device Names and Commands on page 75.

The top of screen displays PAGE, as shown at right, and you see a list of devices (DVD, CABLE, SAT, etc.).

4 Navigate to the page you want to add or hide.

If a page is already visible, it says HIDE? at the top of the screen. If a page is currently hidden, it says ADD?.

5 Press the LIGHT button on the side of the remote control to add or hide the page.

Repeat steps 4 and 5 to add or hide additional pages.

6 When youve finished, press the MAIN button several times to return to normal operation.

Erasing Learned Buttons and Macros

You can erase any commands that were learned from another remote control or any macros you created.

Note This operation does not erase the text used for commands or macros, just the functions that they perform. If you want to delete the text itself, see Editing Device Names and Commands on page 75.

1 Press and hold both the MAIN and ENT buttons for approximately three seconds. The top of the screen displays SETUP.

Note You have 30 seconds to complete each step. After that, the remote control returns to normal operation.

2 Select the ERASE option.

You see this screen:

EDIT

TEXT

PAGE

EXIT

Select PAGE

PAGE

DVD

CABLE

SAT

HD

RADIO

1 OF 2

ERASE

LEARN

MACRO

EXIT

80

3 Select one of the following:

LEARN to erase commands that were learned from another remote control

MACRO to erase macros you created

4 At the next screen, select one of the following:

ALL to erase all learned commands or macros. When you select this option, you see SURE? displayed on the screen. Select SURE? to erase the settings, or select EXIT to cancel.

DEVIC to erase all commands or macros for a specific device. When you select this option, you see a list of devices (DVD, CABLE, SAT, etc.). Select the device whose settings you want to erase. You see ERASED! displayed at the bottom of the screen.

Caution Be careful to select the correct device. If you select the wrong one, you wont have the option to cancel.

KEY to erase a single command or macro. When you select this option, you see a list of devices (DVD, CABLE, SAT, etc.). Select the device that has the command or macro in its menu that you want to erase, then select the command or macro. You see ERASED! displayed at the bottom of the screen.

Caution Be careful to select the correct command or macro. If you select the wrong one, you wont have the option to cancel.

5 Press the MAIN button several times to return to normal operation.

Using Remote Control Punch-Through

The Ensemble HD remote control is pre-programmed to let you operate various devices, each from its own menu. For example, if youve connected a high-definition DVD player, you can operate it from the HD menu; or you can operate a satellite receiver from the SAT menu. However, you may want to be able to operate your high-definition DVD player from the MAIN menu so you can also access the Ensemble HD setup menu, and adjust the picture or sound at the same time, for example. To do this, you create a punch through. This lets you use the remote control to operate certain functions of one device, while you have the menu screen open for another device. (You can punch commands through any menu, not just the MAIN menu.)

Note The volume control is automatically punched through to your home theater system from every device.

Follow these steps to set up a punch-through:

1 Enter Setup mode by pressing and holding both the MAIN and ENT buttons for three seconds. The top of the screen displays SETUP.

Note You have 30 seconds to complete each step. After that, the remote control returns to normal operation.

2 Select the PUNCH option. (You may have to press PAGE or to see it.)

81

3 Select the button group that contains the type of function you want to punch through:

CH: Channel up/down and number buttons (09 and Enter)

PLAY: Play, pause, stop, rewind, and fast-forward

VOD (Video On Demand): Guide, Menu, Info, ESC, arrow buttons (u d l r), and Select

POWER: Power on and off

The bottom of the screen displays PUNCH TO.

4 Select the menu from which you want to be able to operate the device thats not normally controlled by that menu, or press the OFF button to select the MAIN menu. For example, to operate your satellite receiver from the MAIN menu, press the OFF button.

The bottom of the screen displays PUNCH FROM.

5 Select the device that you want to be able to operatefor example, SAT for a satellite receiver.

The bottom of the screen displays SAVED.

6 Repeat steps 3 through 5 to set up additional punch-throughs, or press the MAIN button twice to return to normal operation.

Using an RF Base Station You can use the Ensemble HD remote control to operate components such as a cable box or satellite receiver, even if theyre hidden inside a cabinet. You can do this by using an optional RF base station (radio-frequency receiver) to relay the remote controls commands. An RF base station lets you send commands to components that are not located near the AV controller, or are located inside a closed space such as a cabinet. The base station receives RF commands from the remote control and relays them to each of your components, wherever theyre located. (This is possible because the Ensemble HD remote control emits both IR and RF signals.)

Note The AV controller included with your system can be used in a closed space even without a base station. Thats because the sensor that receives commands for it is located at the top of the screen.

The Ensemble HD remote control is compatible with RF base stations made by Universal Remote Control (www.UniversalRemote.com). Both addressable and non-addressable versions are available. Addressable ones let you avoid interference from other RF remote controls being used nearby. See the next section for instructions on setting up an addressable base station. (If you have a non-addressable base station, you probably wont need to change any of the RF settings.)

Setting Up an Addressable Base Station

If you have an addressable base station, there are several RF settings you may need to adjust on the remote control. At a minimum, you should set the ID # to match the one assigned to your base station.

1 Press and hold both the MAIN and ENT buttons for approximately three seconds. The top of the screen displays SETUP.

82

Note You have 30 seconds to complete each step. After that, the remote control returns to normal operation.

2 Select the RF option. You see this screen:

3 Select the setting you want to adjust:

IR/RF to cause the remote control to emit IR signals only, RF signals only, or IR and RF signals at the same time. If a component receives IR signals directly from the remote control and from the base station at the same time, the signals may interfere with each other, so you should set the remote control to use only RF signals with that component. (You can select the component in step 4.)

ID # to select the receiver ID # of your addressable base station. Select an address other than 0 (zero) to prevent interference from other RF remote controls in the vicinity.

EMITT to route commands through specific emitters plugged into the base station. (The ID # must be set to a non-zero address to select this option.)

BLAST to turn the base stations IR blaster on or off. You may want to turn it off if the blasters high- power LED saturates or overpowers the sensors of some AV components. (The ID # must be set to a non-zero address to select this option.)

4 On the next screen, select whether you want the setting to apply to the menu options for all 10 devices listed on the MAIN menu of the remote control (select ALL) or just the ones for a specific device (select DEVIC).

If you select DEVIC (Device), the next screen lets you select the device you want the setting to apply to. Select from DVD, CABLE, SAT, etc. (Use the PAGE or button to display all the devices.)

5 On the next screen, finish adjusting the selected setting:

For the IR/RF setting, select IR&RF, IR, or RF.

For the ID # setting, select UP or DOWN to change the ID #.

For the EMITT setting, select ALL to route the signal through all the emitters. Or select UP or DOWN to change the Line Output number (this refers to the jack where you plugged in the emitter for a specific component).

For the BLAST setting, select ON or OFF.

6 Select SAVE to save your setting.

7 Select EXIT to return to the SETUP menu, or press the MAIN button twice to return to normal operation.

RF

IR/RF

ID

EMITT

BLAST

EXIT

83

Restoring Remote Control Factory Defaults If you customize the remote control and find that it no longer works correctly, you can restore it to its original settings.

Caution This procedure erases all commands and macros you taught the remote control, and any other customized changes you may have made.

1 To restore the remote control, press and hold the MAIN and stop buttons for about 10 seconds. During this time, you see WARNING flash at the bottom of the screen.

2 When you see the RESET screen shown below, release the buttons.

3 Select SURE? to erase all customized settings, or select EXIT to cancel.

After you restore the remote control, it re-initializes and you see the MAIN menu after several seconds.

RESET

SURE

EXIT

84

85

Remote Control Codes

The program codes provided in this chapter let you set up your remote control to work with devices made by other companies. See Connecting and Using Other Components on page 31 for instructions on using such devices with your system.

If you need to recall the code number you selected for a device, see Recalling Programmed Codes on page 86.

Using the Code Tables The code tables in this chapter (starting on page 87) let you quickly program your remote control to work with different brands of equipment you may own. See Setting Up the Remote Control on page 36 for instructions.

The codes are divided into categories (TV, cable, DVD, etc.). Each category may include different types of components. For example, the DVD category includes TV/DVD combo units. In each section, the code numbers are listed by brand (Sony, Panasonic, etc.). Some brands have more than one code for you to try.

Type of device Included devices See this page...

TV TVs, plasma screens, projectors, and monitors page 87

Cable Cable TV descramblers and tuners WebTVs

page 93

DVD DVD players TV/DVD combos TV/DVD/VCR combos DVD/VCR combos DVD recorders Laser disc players

page 96

VCR VCRs TV/VCR combos

page 99

Audio Amps, preamps, A/V receivers XM radios and tuners

page 102

Satellite Satellite receivers page 108

CD CD players and changers page 111

DVR Digital video recorders (TiVo, Replay, etc.) page 114

Auxiliary Custom installation products Media PC controls Game systems iPod controls Tape decks Lighting systems

page 114

86

Recalling Programmed Codes

In case you need to recall the code numbers you used to program the remote control, you can display them by following these steps:

1 Enter Setup mode by pressing and holding both the MAIN and ENT buttons for three seconds. The top of the screen displays SETUP.

2 Press the PAGE (page down) button to view more options.

3 Select the RECAL (Recall) option.

The screen alternately displays the device names, followed by their code numbers, as shown below.

Tip Pay attention to the page numbers at the bottom of the screen. Page 1 codes go with page 1 devices, and page 2 codes with page 2 devices.

4 Press the MAIN button to return to normal operation.

RECAL

DVD

CABLE

SAT

HD

RADIO

1 OF 2

RECAL

951

001

001

001

951

1 OF 2

87

Code Tables

TV components

Brand Code number

ADMIRAL 072 081 161 160

ADVENT 247 388

AKAI 197 146 248 404 405 458 473 474 475

AMARK 112 143

AMPRO 073 167 157 183

AMSTRAD 052

ANAM 043 054 056 080 112 131

AOC 197 004 112 058

APEX DIGITAL 006 310

ASTAR 477

AUDIOVOX 076 103 273 388 452 453 454 503

AVENTURA 401

AVION 441

BARCO 233

BENQ 423 443

BLAUPUNKT 088

BOXLIGHT 266

BROKSONIC 238

CAIRN 201

CANDLE 197 002 003 004

CAPEHART 058

CETRONIC 043

CITIZEN 197 002 003 004 043 101 103 143

CLASSIC 043

CONCERTO 004

CONTEC 043 050 051

CORONADO 143

CRAIG 043 054

CROWN 043 143

CURTIS MATHES 197 101 004 143

CXC 043

DAEWOO 004 016 043 044 076 077 103 114 125 127 143 269 369

88

DAYTRON 004 143

DELL 319 320 321

DIBOSS 329

DIGITAL PROJECTION 437

DREAMVISION 235 312 313 314 343 344 345

DURABRAND 401

DWIN 177 257

DYNASTY 043

DYNATECH 062

DYNEX 399

EIKI 187

ELECTROGRAPH 470

ELECTROHOME 024 076 143 196

EMERSON 197 004 005 028 043 047 048 050 051 076 077 096 143 151 153 154 155 401

EPSON 324

ESA 323

FISHER 007 057

FUJITSU 198 223 219 246 299 346 396 410

FUNAI 028 043 052 401

FUTURETECH 043

GATEWAY 242 268

GE 197 008 009 034 056 073 074 130 144 155 160 161 165 004 091 157 183

GEM 391

GOLDSTAR 004 102 106 112 113 116 119 127 143

GRUNDIG 220 083

HAIER 501 502

HALL MARK 004

HANNSPREE 381

HISENSE 419 442

HITACHI 004 009 010 011 012 023 075 143 158 163 166 072 221 250 311 361 380 411 460

HP 316 327 378 379 421

HUMAX 518

TV components (continued)

Brand Code number

89

HYUNDAI 337 338

ILO 472

INFINITY 164

INFOCUS 230 330 331 332 333 252 409 449

INSIGNIA 350 354 399 400 401 402 403 454 457

JBL 164

JCPENNEY 197 004 008 009 024 030 065 101 143 156 160

JENSEN 013

JVC 034 038 070 083 145 199 210 240 241 244 245 317 318 406 420 471

KEC 043

KENWOOD 197 070

KLEGG 466

KLOSS 002 059

KMC 143

KNOLL SYSTEMS 230 409

KONKA 457

KTV 197 043 143 154

LG 243 284 283 286 363 364 365 366 522 523

LODGENET 072

LOEWE 222 223 224 164 322 422

LOGIK 072

LUXMAN 004

LXI 166 007 015 052 081 160 164

MAGNAVOX 197 003 004 022 059 060 061 063 064 127 160 164 094 226 264 390 467

MARANTZ 197 164 184 397 281

MATSUI 164

MAXENT 242

MEMOREX 007 072 004

METZ 088

MGA 197 004 024 028 042

MINERVA 088

MINTEK 362

MISAKAI 401

TV components (continued)

Brand Code number

90

MITSUBISHI 004 024 028 040 042 109 124 146 191 225 237 267 300 348 450 519 525

MTC 197 004 062 101

NAD 015 025

NEC 132 130 134 197 040 016 024 056 019 236 237 262 272 281 428 448

NIKEI 043

NORCENT 367

NUVISION 351

OLEVIA 432 376 394 504

ONKING 043

ONWA 043

OPTOMA 249 265 270 360

OPTONICA 019 081

ORION 096

PANASONIC 034 056 080 092 164 208 261 296 295 297 298 359 377 383 429 430 524

PHILCO 197 003 024 056 059 060 063 064 164 004

PHILIPS 197 003 004 005 038 059 093 164 127 184 206 259 260 264 274 294 424 425 431

PHILIPS/MAGNAVOX 239 260 294

PIONEER 197 018 023 025 116 135 190 203 204 209 234 237 334 335 336 374 385 393 397 438 447 459 520

PLANAR 513

POLAROID 352 353 354 355 356 357 358 388 493 494 505 506 507 508

PORTLAND 077 004 143

PROJECTION DESIGN 417 418

PROSCAN 144 160 161 165 167

PROTON 004 058 131 143 171 173 193 392

PROTRON 392 398 498 499 500

PROVIEW 493

QUASAR 034 056 092

RADIO SHACK 019 043 143 004 127

RCA 160 161 165 065 156 144 197 004 023 024 056 074 152 333

REALISTIC 007 019 043 047

REVOLUTION HD 466

ROCTEC 186

TV components (continued)

Brand Code number

91

RUNCO 168 169 178 179 180 181 182 183 073 157 340 341 342 395 414 415 416 476

SAMPO 197 058 004 202

SAMSUNG 004 050 089 101 105 127 143 160 211 228 229 253 254 258 275 309 375 384 427 434 461 462 463 464 515 516 517

SANSUI 399

SANYO 166 007 020 053 057 082 187 266 347 509 510 511 512

SCEPTRE 276

SCOTT 004 028 043 048 143 497

SEARS 015 030 004 007 028 057 143 094 160 082 165 166

SELECO 189 200 212 227 205

SHARP 170 081 019 028 029 014 004 022 143 175 214 251 263 306 307 308 326 468 496

SHERWOOD 349

SIEMENS 088

SIGNATURE 072

SIM2 205 200 313

SOLE 231 232

SONY 070 085 139 147 126 185 194 207 213 277 278 279 412 413 444 445 446 491 492 521

SOUNDESIGN 004 028 003 043

SPECTRICON 112

SPECTRONIQ 499 500

SSS 004 043

SUPERSCAN 401

SUPRE MACY 002

SVA 328

SYLVANIA 197 003 059 060 063 064 164 044 160 127 052 401 469 514

SYMPHONIC 052 401

SYNTAX OLEVIA 376 394 432 504

TANDY 081

TATUNG 056 062

TCL 426

TECHNICS 034 080

TECHWOOD 004

TV components (continued)

Brand Code number

92

TEKNIKA 002 003 004 024 028 043 072 101 143

TELEFUNKEN 037 046 086 087

TELERENT 072

TERA 172

THOMPSON 215

TMK 004

TOSHIBA 007 015 030 040 062 101 138 216 287 290 291 230 288 289 292 293 315 237 325 382 455 456 465 479 480

TOTEVISION 143

UNIVERSAL 008 009

VIDEO CONCEPTS 146

VIDIKRON 174 184 188 192 340 342 395 406 414 415 439 440

VIDTECH 004

VIEWSONIC 271 242 389 390 433

VIORE 472

VITO 478

VIZIO 386 387

WARDS 004 008 009 019 028 060 061 063 064 072 074 143 164 034

WESTINGHOUSE 076 077 280 435 436 495

WINBOOK 339

YAMAHA 197 004 370 371 372 373 407 408 451

YORK 004

YUPITERU 043

ZENITH 072 073 095 103 157 183 217 243 282 283 284 285 286 363

ZONDA 112

TV components (continued)

Brand Code number

93

Cable components

Brand Code numbers

ABC 103 003 004 039 042 046 053

ADELPHIA 043 074 110 111

ADVANCED NEWHOUSE 043

ALTRIO 043

AMERICAST 099

ANTRONIX 014

ARCHER 005 007 014

ARMSTRONG 074

AT&T BROADBAND 074

ATLANTIC BROADBAND 043 074

BELL SOUTH 099

BLUE RIDGE 043 074

BRESNAN 074

BUCKEYE COMM 074

CABLEVISION 108 043 074

CENTURION 092

CENTURY 007

CHARTER 043 074 110 111

CITIZEN 007

COGECO 074

COMBANO 080 081

COMCAST 110 043 074

COMSAT 074

COMTRONICS 030

COX DIGITAL CABLE 043 074

DIGICABLE 101

EAGLE 020 030 040

EASTERN 057 066

ELECTRICORD 032

GEMINI 008 054

GE 072

GENERAL INSTRUMENT 103 002 003 004 008 009 010 069 074 104

94

GNC 099

GOLDEN CHANNEL 030

HAMLIN 049 050 055

HITACHI 103 055

INSIGHT 074

JERROLD 103 002 003 004 008 009 010 069 074 104 109 110

M-NET 037

MAGNAVOX 010 012 064 079 094

MASSILLON 074

MEDIA ONE 107

MEDICOM 074

MEMOREX 052

MOTOROLA 103 002 003 004 008 009 010 069 074 104 109 110 111 112 120

MOVIE TIME 028 032

MOXI 111

NCTC 074

NOVAPLEX 092

NSC 015 028 038 071

OAK 031 037 053

PACE 043 074

PANASONIC 044 047

PARAGON 052

PHILIPS 006 012 013 020 085

PIONEER 103 034 051 063 076 105 043

PRUCER 059

PTS 011 071 074

PULSAR 052

QUEST 112

RCA 047

RCN 074

RECOTON 098

REGAL 049 050

REGENCY 057

Cable components (continued)

Brand Code numbers

95

RODGERS 043

SAMSUNG 030 123

SCIENTIFIC ATLANTA 003 011 041 042 043 045 046 123

SEREN 043

SERVICE ELECTRIC 074

SHAW 074

SIGECOM 043

SIGNAL 030

SIGNATURE 103

SL MARX 030

SONY 108 096

SPRUCER 047 078

STARCOM 002 004 008 009

STARGATE 008 030 097 104

SUSQUEHANNA 043 074

TADIRAN 030

TIMELESS 030

TIME WARNER 043 074

TOCOM 039 040 056

TOSHIBA 052

UNIKA 007 014

UNITED CABLE 004 053

UNIVERSAL 005 007 014 032 035

VIDEOTRON 043

VIEWSTAR 012 015 018 086 087 088 089

VERIZON 121 110

WIDE OPEN WEST 043 099

ZENITH 052 060 093 100

Cable components (continued)

Brand Code numbers

96

DVD components

Brand Code numbers

ADCOM 157

AIWA 136 146

ALPINE 098

AKAI 281

APEX DIGITAL 087 111 112 115 116 236

ARCAM 122

AUDIOVOX 284

CALIFORNIA AUDIO 021 124

CAMBRIDGE AUDIO 215 216

CARY AUDIO DESIGN 174

CINEVISION 219

CLASSE 167

COBY 258 260

CYBERHOME 133 227 271 313

DAEWOO 132

DENON 007 080 138 173 181 287 288 206 207

DURABRAND 143

EMERSON 143

ESA 143

GATEWAY 175

GE 026 027

GRADIENTE 021

GRUNDIG 083

GO VIDEO 137 091 217 218 219 220 221 222 224

HARMAN KARDON 084 140

HITACHI 101

FUNAI 143 120

ILO 268

INSIGNIA 143 292 297

INTEGRA 142 180 192 280

JVC 012 168 203 212 257 302

KENWOOD 123 151 152 013

97

KISS 179 279

KLH 135

KRELL 104

LECSON 126

LEXICON 148 305

LG 303 057 074

LINN 306

LITEON 264 265

MAGNAVOX 096 066 143 282 032 121

MALATA 267

MARANTZ 083 105 201 202 315 211

MCINTOSH 125

MEMOREX 163

MERIDIAN 153

MINTEK 111 282

MITSUBISHI 017 121

MYRYAD 134 102

NAIM 226

NAD 088 155 278 121

NAKAMICHI 103

ONKYO 076 035 180 274 280 314

OPPO 266 311

PANASONIC 285 021 042 138 139 144 150 198 199 205 259 289 113

PARASOUND 245

PHILIPS 066 095 105 166 176 276 277 032

PIONEER 304 023 092 099 107 108 131 162 172 178 213 232 272 283 106 117 121

POLAROID 233 234 235 236 237 284 295 296 297

PRIMARE 193 194

PROCEED 086

PROSCAN 026 027

RCA 026 027 273 290 307 002

RJTECH 269

ROTEL 204

DVD components (continued)

Brand Code numbers

98

SAMSUNG 275 056 070 119 137 159 165 170 200 254 301

SANSUI 154

SANYO 147 075

SENSORY SCIENCE 217 222 223

SHARP 094 294 152 013

SHERWOOD 245 246 247 248 249 250

SONY 286 033 118 126 145 160 189 191 238 239 240 241 242 243 251 252 253 261 262 263 053 110

SPECTRONIQ 310

SUPERSCAN 143

SV2000 143

SYLVANIA 143

SYMPHONIC 143

TAG MCLAREN 156

TEAC 270

THETA DIGITAL 023 032

THOMPSON 026 027

THULE 177

TOSHIBA 273 035 034 128 141 130 164 183 184 185 186 187 188 214 300 152 106

TRUTECH 293

VENTURER 149

VINC 161 308

YAMAHA 042 089 066 158 166 195 196 197 043 129

ZENITH 057 074 091 182

DVD components (continued)

Brand Code numbers

99

VCR components

Brand Code numbers

AIWA 034 161 169

AKAI 016 043 046 124 125 142 146

AMPRO 072

ANAM 031

AUDIO DYNAMICS 012 023 039 043

BROOKSONIC 035 037 129

CANON 028 031

CAPEHART 108

CRAIG 003 040 135

CURTIS MATHES 031 041

DAEWOO 005 007 010 065 108 110 111 112 116 117 119

DAYTRON 108

DBX 012 023 039 043

DYNATECH 034 053

ELECTROHOME 059

EMERSON 005 006 017 025 027 029 031 034 035 036 037 046 101 116 129 131 138 153 162

FISHER 003 008 009 010

FUNAI 034

GE 031 063 072 107 109 144 147

GO VIDEO 132 136 155 040 115

GOLDSTAR 012 013 020 101 106 114 123

HARMAN KARDON 012 045

HITACHI 004 018 026 034 043 063 137 150 160 013

INSTANTREPLAY 031

JCL 031

JCPENNEY 012 013 015 040 066 101

JENSEN 043

JVC 012 031 043 048 050 055 060 130 150 152 166 172 173

KENWOOD 014 048 034 047

LG 171

LLOYD 034

LXI 003 009 017 034 106

100

MAGIN 040

MAGNAVOX 031 034 041 067 068 156 164

MARANTZ 012 031 067 069 156

MARTA 101

MATSUI 027 030

MEI 031

MEMOREX 003 010 014 031 034 053 072 101 102 134 139

MGA 045 046 059

MINOLTA 013 020

MITSUBISHI 013 020 045 046 051 059 061 142 151 049 168 174 175

MTC 034 040

MULTITECH 024 034

NEC 012 023 039 043 048

NORDMENDE 043

OPTONICA 053 054

ORION 025

PANASONIC 066 070 083 133 140 145 157 163 074 167

PENTAX 013 020 031 063

PHILCO 031 034 067

PHILIPS 031 034 054 067 071 101 156

PILOT 101

PIONEER 013 021 048

PORTLAND 108

PULSAR 072

QUARTZ 002 014

QUASAR 066 145 075

RADIO SHACK 123

RCA 013 020 041 107 109 140 144 145 147 034 040 158

REALISTIC 003 008 010 014 031 034 040 053 054 101

RICO 058

RUNCO 148

SALORA 014

SAMSUNG 032 040 066 102 104 107 109 112 113 115 120 122 125

VCR components (continued)

Brand Code numbers

101

SANSUI 022 043 048 135

SANYO 003 007 010 014 134 102

SCOTT 017 037 112 129 131

SEARS 003 008 009 010 013 014 081 101 017 073 112

SHARP 031 054 149 159 165

SHINTOM 024

SIGNATURE 034

SONY 003 031 052 056 057 058 076 077 078 149 154

SOUNDESIGN 034

STS 013

SYLVANIA 031 034 059 067

SYMPHONIC 034

TANDY 010 034

TATUNG 039 043

TEAC 034 039 043

TECHNICS 031 070

TEKNIKA 019 031 034 101

THOMAS 034

TMK 006

TOSHIBA 008 013 042 047 059 079 082 112 131 081 170

TOTEVISION 040 101

UNITECH 040

VECTOR RESEARCH 012

VICTOR 048

VIDEO CONCEPTS 012 034 046 141

VIDEOSONIC 040

WARDS 003 013 017 024 031 034 040 053 054 131

YAMAHA 012 034 039 043

ZENITH 034 048 056 058 072 080 101 171

VCR components (continued)

Brand Code numbers

102

Audio components

Brand Code numbers

ADC 007

ADCOM 082 092 225 161 269 355 356 366

AIWA 018 104 170 202 203 213 211 188

AKAI 138 189

AMC 038 125 126 127 128 258 281 282

AMEND 054

AMX 196

ANGSTROM 142

ANTEX ELECTRONICS 588

ANTHEM 335 336 337 338 339

ARAGON 157 158 042 043 081 112

ARCAM 141 325 418 419 504 590 591 592 593 594

ARCAM 504 591

ATLANTIC TECHNOLOGY 342

AUDIO ACCESS 147

AUDIO ALCHEMY 135

AUDIO CONTROL 448 572 623

AUDIO DESIGN ASSOCIATES 194 221 011

AUDIO EASE 021 196 207

AUDIO FILE 071

AUDIO MATRIX 167

AUDIO RESEARCH 399 406 423 424 425 426

AUDIO SOURCE 273

AUDIO TECHNICA 134

B & K 096 097 298 299 300 301 302 303 304 305 306 307 308 309 310 311 312 313 314 315

BOSE 409 460 548 070 170 224 347 459 532

BOSE 170 532

BOSTON ACOUSTICS 447

BRIX 555

BRYSTON 023 551

CAMBRIDGE AUDIO 522 523 524 525 630 683

CARVER 006 027 028 061 071 201 214 226 180 185 022 029 077 284

103

CARY AUDIO DESIGN 443 519

CASIO 076

CHIRO 140

CINEMA SOUND 034 134

CITATION 148 272

CLARION 026

CLASSE 410 411 484 537 538

COLORADO VNET 539

COMPAQ 382

CURTIS MATHES 076

DELPHI 415 515

DENON 340 400 422 002 034 109 215 229 230 027 037 234 259 316 330 341 349 350 396 401 402 444 564 568 569 601 602 649 650 651 677 678 679 680 681

EAD 099 098 466 467

EIGER 149

ELAN 468 472 469 470 471 057 290 371 473 474 475 476 477 481 482 483 508 509

ESCIENT 368 381 393 451 452 453 454

FANFARE 352

FISHER 047 214 180 182 297

FLEXTRONICS 378

FOSGATE 062 231 342

GE 056 260

GOLDSTAR 008

HAFLER 174

HALCRO 596 597

HARMAN KARDON 318 231 233 254 153 154 118 121 227 277 317 329 365

HITACHI 020

IMERGE 371

INKEL 197

INSIGNIA 589

INTEGRA 486 441 570 354 371 438 439 440 442 487 586

JAMO 398

JBL 263 621 622

Audio components (continued)

Brand Code numbers

104

JCPENNEY 076 216

JEFF ROWLAND 206

JENSEN 058

JVC 279 240 163 191 114 266 291 389 390

KEF 530

KENWOOD 412 320 026 066 145 146 181 190 197 192 182 199 151 222 180 005 280 319 367 374 413 414 420 517 550

KENWOOD 550

KINERGETICS 220 140

KLH 331

KLIPSCH 157 158 042 043 081 112

KNOLL 531

KOSS 216 573

KRELL 376 384 500 624 150 072 321 497 498 499 672 673 674

KYOCERA 007

LEXICON 357 360 120 235 236 237 324 358 359 361 362 363 364

LINN 124 377

LUXMAN 137 139 052 165 115 004 009

LXI 076 056

MAGNAVOX 086 164 152 208

MARANTZ 488 492 385 006 028 031 040 063 185 186 251 265 119 289 326 327 328 371 489 490 491 493 563

MARK LEVINSON 322

MCINTOSH 238 286 496

MCS 076

MERIDIAN 100 012 013 628

MICRO LAB 394

MICROMEGA 119

MITSUBISHI 242 243 204

MONDIAL 157 158 042 043 081 112

MOTOROLA 386

MUSICAL FIDELITY 407 408 647 648

MUSICAL FIDELITY 408 648

MYRYAD 276 293 455 456 457

Audio components (continued)

Brand Code numbers

105

MYRYAD 457

NAD 186 113 283 478 479 598 603 604 605

NAD 113

NAIM 533 534 535

NAIM 535

NAKAMICHI 111 244 245 172 183 287 323 450 615

NEC 176

NETSTREAMS 616 617 618 619 620

NILES 403

NIRO 343

NUVO 404 405 606 607 608 609 610

NUVO 404 405 606 607

OLIVE 584

ONKYO 486 441 017 046 064 107 108 187 079 080 090 179 209 270 275 438 439 440 442 486 487 536 552 586 629

OPTIMUS 026 041 138

OUTLAW 342

PANASONIC 032 195 219 177 292 383 516 626 627

PARASOUND 333 334 553 554 129 130 132 261 294 295

PASS LABS 431

PHAST 196

PHILIPS 249 250 251 063 119 296

PIONEER 480 542 014 033 039 044 045 050 069 159 168 116 035 078 198 397 513 518 520 521 543 544 545 546 547 556

PIONEER 556

PLINIUS 458

POLKAUDIO 029 514

POLKAUDIO 514

PRIMARE 461 462 463 464 465

PRIMARE 465

PROCEED 144 268

QUAD 526

RCA 010 048 117 156 067 288 549

REALISTIC 019 056 073 075 095

Audio components (continued)

Brand Code numbers

106

REQUEST 351 511 611 612 613

REVOX 162

ROKU 506 507

ROTEL 501 502 503 074 083 085 654

RUSSOUND 379 391 392 445 446 527 528 529

RUSSOUND 445 446

SAMSUNG 016 571 653

SANSUI 040 048 110 119 065 228

SANYO 047 059

SCOTT 019 091

SEARS 076

SHARP 026 051 094 131 175 181 652

SHERWOOD 447 024 038 055 102 103 105 106 051 030 348 370 388 562 675

SIMAUDIO 449

SIRIUS 585 555

SIRIUS 585 555 550

SLIM DEVICES 512

SONY 372 417 574 369 018 084 093 223 247 248 160 166 015 101 184 218 271 353 380 395 421 575 576 577 631 640 641 642 632 633 634 635 636 637 638 639

SONY 380

SOUNDESIGN 036

SOUNDMATTERS 375

SOUNDSTREAM 084 088

SSI 068

STS 007

SUGDEN 430

SUMO 171

SUNFIRE 344 345 346 494 495

TAEKWANG 138

TAG MCLAREN 387

TASCAM 625

TASCAM 625

TEAC 005 019 049 111 212 217

Audio components (continued)

Brand Code numbers

107

TECHNICS 122 176 193 219 178 177 200 257 262

THETA DIGITAL 136

THULE 505

TOSHIBA 060 087 198 278 510

TURTLE BEACH 416

WARDS 180

XANTECH 508 509

XM SATELLITE RADIO 415 514 515

YAMAHA 427 557 655 643 644 026 253 169 067 123 133 173 205 264 232 089 274 285 332 373 428 429 432 433 434 435 436 437 540 541 558 559 560 561 565 566 567 578 579 580 581 582 583 599 600 645 646 656 657 658 659 660 661 662 663 664 665 666 667 668 669 670 671 676

YBA 485

ZENITH 143 210

ZON 587

Audio components (continued)

Brand Code numbers

108

Satellite components

Brand Code numbers

ALPHASTAR 123

AMPLICA 050

ASTON 206

ATLANTA DTH 203

BIRDVIEW 129 113 051 126

BSR 053

CABLEVISION 148

CAPETRONICS 053

CHANNEL MASTER 013 014 015 018 036 055

CHAPARRAL 008 009 012 077

CITOH 054

COOLSAT 211

CURTIS MATHES 050

DISH NETWORK 122 167 168 184 185 186 187 188

DIRECTV 173 193 220 221 223 224 225 226 227 228

DRAKE 005 006 007 010 011 112 116 141 052

DREAM MULTIMEDIA 191 205

DX ANTENNA 024 046 056 076

ECHOSTAR 038 040 057 058 093 094 095 096 097 098 099 100 122 167 168 184 185 186 187 188

ELECTROHOME 089

EURO PLUS 114

EUROSAT 114

EXPRESSVU 122

FORCE 176

FORTEC STAR 177 178

FUJITSU 017 021 022 027 133 134

GE 151 106 150

GENERAL INSTRUMENT 003 004 016 029 031 059 101 148

GOI 122

HITACHI 139 140

HIRSCHMANN 202

HOME CABLE 080 044 029

109

HOUSTON TRACKER 033 037 039 104 057 051

HTS 122

HUGHES 068 154 161 162 165 166 220 221 223 224 225 226 227 228

HYTEK 053

HYUNDAI 149

ICR 023

JANIEL 060 147

JERROLD 148

JVC 122

KATHREIN 108

KPN 208

LEGEND 057

LG 170

LUXOR 144 062

MACOM 010 059 063 064 065

MARANTZ 152 153

MEMOREX 057

MICRONIK MULTIMEDIA 207

MITSUBISHI 068 154

MOTOROLA 148 171

NEXT LEVEL 148

NEXTWAVE 028 124 125

NORSAT 069 070

NTL 209

NV 195 196 197

PACE 143

PANASONIC 142 060 160

PANSAT 121 172

PERSONAL CABLE 117

PHILIPS 071 152 153 068 154 156 201

PL 023 026

PRESIDENT 019 102

PRIMESTAR 110 030

Satellite components (continued)

Brand Code numbers

110

PROSAT 072

PROSCAN 151 106 150

RADIOSHACK 148

RCA 151 106 150

REALISTIC 043 074

SAB 195 196 197 198 199 200

SAMSUNG 155 123 163 169 175 179

SATCRUISER 192

SATELLITE SERVICE 028 035 047 085

SKY 164 171 174 204

SONY 103 104

STARCAST 041

STAR CHOICE 148

SUPERGUIDE 020 124 125

TEECOM 023 026 075 087 088 090 107 130 137

TOSHIBA 002 127 157 158 068 154

TOWN & COUNTRY 023 026

UNIDEN 016 025 042 043 044 045 048 049 078 079 080 086 101 135 136

VIEWSTAR 115

VOOM 148

WINEGARD 128 146

ZENITH 081 082 083 084 091 120 159

Satellite components (continued)

Brand Code numbers

111

CD players

Brand Code number

ADCOM 062 042

AIWA 059 012 065 088 089 105 122 170 187

AKAI 085 195 202

AMC 231 232

AMEND 118

ARCAM 238 275

AUDIO ACCESS 119 147

AUDIO EASE 165

AUDIO TECHNICA 046

BSR 037 057

CALIFORNIA AUDIO 103 008

CAMBRIDGE AUDIO 268

CAPETRONIC 063

CARRERA 057 080

CARVER 185 041 044 050 086 107 130 134 135 138 139 203 204 167

CASIO 111 182

CARY AUDIO DESIGN 261 262 289 290 291 292

CLASSE 267

CLARINETTE 182

CREEK 159

CROWN 035

DCS 294

DENON 002 123 281

EMERSON 042 069 102

FISHER 050 185 134 008

FRABA 111

GENEXXA 010 069 102

GOLDSTAR 080

HAITAI 093

HARMAN KARDON 018 033 047 208 272

HITACHI 042 175

INKEL 130 143 144

112

INTEGRA 030 273

JCPENNEY 014 061 092 141

JENSEN 158

JVC 004 022 136 163 213 214 242 243 286

KENWOOD 185 007 023 055 071 072 142 137 254

KOSS 061

KRELL 241 279 285

KYOCERA 005

LOTTE 102

LUXMAN 011 028 070 076 249 252

LXI 059

MAGNAVOX 044 107

MARANTZ 027 041 044 051 077 107 209 246 274 296 297

MCINTOSH 212 247

MCS 014 073 092

MEMOREX 010

MISSION 044 107

MITSUBISHI 179

MITSUMI 153

MODULAIRE 182

MONDIAL 147

MUSICAL FIDELITY 258 284

MYRYAD 244 265

NAD 006 005 067 178 293

NAIM 271

NAKAMICHI 217 218 219 095

NEC 014 062

NIKKO 046

NSM 044 107

ONKYO 030 038 039 168 169 273

OPTIMUS 010 050 057 058 081 082 083 085 093 195

PANASONIC 103 201 172 008 068 248

PARASOUND 233 240

CD players (continued)

Brand Code number

113

PHILIPS 041 044 107 246 253

PIONEER 010 020 025 056 174 175 176 257 263

PLINIUS 288

PRIMARE 266

PROCEED 239

PROTON 044 107 228

QUAD 269

QUASAR 103 008

RADIO SHACK 182

RCA 017 042 150 276

REALISTIC 042 050 051 102 181 182 187

ROTEL 044 107 161 178 250

SAE 044 107

SANSUI 044 069 107 128 171 190 125

SANYO 050

SCOTT 069 102

SHARP 026 031 051 066

SHERWOOD 003 019 051 096 112 115 119 166

SIGNATURE 033

SIMAUDIO 280

SONY 048 081 097 126 133 177 225 226 164 229 230 259 260 277 278

SOUNDESIGN 251

SUGDEN 264

SUMO 155

SYLVANIA 044 107

SYMPHONIC 052 181

TAEKWANG 195 085

TANDY 010

TEAC 015 034 036 051 052 101 131 140 079 145

TECHNICS 060 103 200 172 184 008 068

TECHWOOD 076

THETA DIGITAL 234 235 270

TOSHIBA 006 067 091 160 148

CD players (continued)

Brand Code number

114

VECTOR RESEARCH 080

VICTOR 004 022 114 124

WARDS 185 033

YAMAHA 024 046 054 186 183 245 282 283 287

YORX 182

DVR components

Brand Code numbers

DIRECTV 117 121 122 123 124 125 126 127 128

HUGHES 117 121 122 123 124 125 126 127 128

HUMAX 118 121 122 123 124 125 126 127 128

PHILIPS 090 117 121 122 123 124 125 126 127 128

PIONEER 117 118 121 122 123 124 125 126 127 128

RCA 109

REPLAY TV 075

SONY 104 105 131

TIVO 090 117 118 121 122 123 124 125 126 127 128

Auxiliary components

Brand Code numbers

3M 152

ADS TECH 404

AHANIX 260

AIWA 164 015 071 100 114

ALGOLITH 415 475

APPLE 401 412 476

ARCHER 155

AUDIO AUTHORITY 427 428

AURORA 300

AUTON 191 434

AURORA MULTIMEDIA 220

AVERMEDIA 437 460

CD players (continued)

Brand Code number

115

BEDIENUNGSANLEITUNG 221

BOSE 409

CALYPSO 491 492 493 494

CE LABS 298

CELADON 211

CRESTRON 213 214 215 216 217 218

D-BOX 440

DA LITE 269

DCS 468 469 470

DDI 403

DELL 261 262 263 264 265 266 267 268

DLINK 435

DLO 418

DMX 156

DRAPER SCREEN 204

DREAMVISION 097

DVDO 299 423

DWIN 080 253

ELAN 451 452 453 454 455 456 457 458 441 442 443 444 445 446 447 448 449

ELECTROKINETICS 438

ELITE SCREENS 431 432

EVERQUEST 206

EXTRON 151 433

FARENHEIT 430

FAROUDJA 184 254

FOCAL 436

FUJI 209

GATEWAY 261 262 263 264 265 266 267 268

GRIFFIN 471

HAUPPAUGE 294 295

HP 252 261 262 263 264 265 266 267 268

HUNTER DOUGLAS 219

INTEGRA 439

Auxiliary components (continued)

Brand Code numbers

116

IOGEAR 407

IPORT 419

JERROLD 153

JVC 185 416 106 116 239 240

KALEIDESCAPE 259 459

KENSINGTON 406

KENMORE 251

KENWOOD 185 005 013 023 026 064 145 146 181 190

KEY DIGITAL 273 274 275 461 462 463 464 465

KEYSPAN 297

KLIPSCH 425

LG 296

LINKSYS 270

LUMAGEN 472

LUTRON 417 077 158 159 306 308 309

LUXOM 424

MAKITA 186 201

MARANTZ 450 014 027 056 065 087

MICROSOFT 107 252 261 262 263 264 265 266 267 268 408

MINDPATH 205

NETGEAR 477

NILES 160 187 272

NSM 161

NTI 421

ONKYO 439 002 012 016 017 018 019 115

PIANO DISC 085

PINNACLE 405

POLK AUDIO 162

PRIMARE 402

RCA 258

RUNCO 466

RUSSOUND 081

SCIENTIFIC ATLANTA 156 163

Auxiliary components (continued)

Brand Code numbers

117

SHERWOOD 467 038 004 028 030 033 034

SIMA 082 429

SOLO ELECTRONICS 207

SOMFY 078 079 411

SONANCE 419

SONY 164 165 166 271 261 262 263 264 265 266 267 268 414 020 022 052 084 089

SPEAKERCRAFT 473 474

STARCOM 153

TEN TECHNOLOGY 401

TURBOSCAN 167

VELODYNE 203 413

WURLITZER 410

XANTECH 168 169 170 171 172 276 277 278 279 280 281 282 283 284 285 286 287 288 289 290 291 292 293 420 426 188 189

Auxiliary components (continued)

Brand Code numbers

118

119

Specifications

For projector specifications, see the Users Guide that came with your projector. For all other components, see these sections:

Playable Disc Types below

Screen Specifications on page 120

Remote Control Specifications on page 120

Powered Subwoofer Specifications on page 121

Surround Speaker Specifications on page 121

AV Controller Specifications on page 122

Playable Disc Types The Ensemble HD systems DVD player accepts DVDs and compact discs in both 3-inch (8 cm) and 5-inch (12 cm) sizes.

In addition, you can play recordable DVDs (marked DVD-R) and recordable compact discs (CD-R and CD-RW). Discs must be recorded in the standard DVD Video or Compact Disc Digital Audio format, and must be finalized to be playable. Data CDs and DVDs containing MP3 or WMA audio files, or picture files in JPG format, can also be played (ISO 9660 format). You cannot play other types of discs, such as DVD-Audio, SACD, CD-ROM, DVD-RW, DVD-RAM, or DVD-ROM. Depending on the characteristics of your recorder or media, some recordable discs may not play properly.

DVDs must be recorded in the NTSC color system and be encoded for playing in Region 1. Commercial DVDs should be marked with the Region 1 symbol:

Note Many commercial DVDs incorporate a copy protection system. If you attempt to copy such a disc, the copy will be visually distorted. Please see Responsible Use of Copyrighted Materials on page 123.

120

Screen Specifications

General

Built-in Speaker System

Remote Control Specifications

Screen Size 100" (254 cm), nominal diagonal

Aspect Ratio 16:9 (HDTV widescreen format)

Image Area (WH) 87" 49" (221 124.5 cm)

Black Drop Length 12" (30.5 cm)

Screen Material 1.1 high-gain matte white

Motor 110 volt Somfy electric

Installation Wall or ceiling

Screen Casing Dimensions (WHD) 100" 6.0" 9.5" (254 15.2 24.1 cm)

Weight 74 lb (33.6 kg)

Speakers Left/right: (1) 4.5" (114 mm) midrange + (1) 1" (25 mm) titanium tweeter Center: (2) 4.5" (114 mm) midrange + (1) 1" (25 mm) titanium tweeter

Frequency Response 100 Hz to 20 kHz 3dB

Nominal Impedance 8 ohm

Crossover Frequency 3.75 kHz, 3rd order

Sensitivity 89dB

Type LCD backlit display; programmable

Learning Capability 784 commands 472 macros, up to 190 steps each

IR Range (direct line-of-sight via infrared) 20 ft (6.1 m), depending on lighting conditions

IR Frequency 15 kHz to 100 kHz

RF Range (radio frequency) 50 to 100 ft (15 to 30 m), depending on environment

RF Frequency 418 MHz

Weight 8 oz (230 g), with batteries

Size (LWH) 8.5" 2.4" 1.0" (21.6 6.1 2.5 cm)

Batteries 4 AAA alkaline batteries

121

Powered Subwoofer Specifications

Bass Driver

Amplifier

Physical

Surround Speaker Specifications

Type Ported enclosure, front-firing

Size 10" (254 mm), long throw

Frequency Response 32 to 100 Hz, 3dB

Type 5.1-channel with built-in equalizer

Peak Output 105dB in 3000 cubic feet

Output Power 150 W (subwoofer) 70 W (center channel) 40 W 4 (front left/front right/left surround/right surround)

Frequency Response 20 Hz to 20 kHz 2dB

Boundary Controls 5 pre-programmed EQs, manually selectable depending on installed location of screen

Anti-boom Adjustment Manually selectable frequency and gain; smooths room-induced bass peak

Dimensions (WHD) 14.9" 16.1" 18.0" (37.8 40.9 45.7 cm)

Weight 35 lb (16 kg)

Type 4" (10 cm) coaxial speaker; side/reflective surround

Speaker Mounting Built into projector enclosure; also removable for ceiling installation

Frequency Response 100 Hz to 20 kHz

Dimensions of Projector Enclosure (WHD) 26.9" 6.4" 12.7" (68.3 16.3 32.3 cm)

Weight of Projector Enclosure 15 lb (6.8 kg)

122

AV Controller Specifications

Built-in AV Capabilities DVD/CD player AM/FM tuner USB flash drive

Playable Disk Types See page 119

Video Processor Pixelworks chipset

Video Output 1080p/720p, depending on projector

Video Input Ports HDMI (2) Component video S-video Composite video (CVBS)

Compatible Video Formats NTSC

Audio Input Ports (for use with video sources)

HDMI Optical Coaxial Analog

Other Audio Ports Audio 1 (analog input for use with tape deck) 2Ch Out (analog output for use with tape deck) Audio 2 (analog input for use with MP3 player or other portable audio device) DB15 (5.1 channel output; connects to subwoofer)

Video Output Port HDMI

Size (WHD) 13.5 in 4.0 in 10.5 in (34.3 10.2 26.7 cm)

Weight 7.5 lb (3.4 kg)

123

Notices

Responsible Use of Copyrighted Materials Epson encourages each user to be responsible and respectful of the copyright laws when using any Epson product. While some countries laws permit limited copying or reuse of copyrighted material in certain circumstances, those circumstances may not be as broad as some people assume. Contact your legal advisor for any questions regarding copyright law.

Use of this equipment for other than private viewing of programs broadcast on UHF or VHF, or transmitted by cable or satellite companies, for the use of the general public may require authorization from the broadcast/ cable/satellite company and/or program owner.

FCC Compliance Statement For United States Users

This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio or television reception. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause interference to radio and television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

Reorient or relocate the receiving antenna.

Increase the separation between the equipment and receiver.

Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.

Consult the dealer or an experienced radio/TV technician for help.

WARNING

The connection of a non-shielded equipment interface cable to this equipment will invalidate the FCC Certification of this device and may cause interference levels which exceed the limits established by the FCC for this equipment. It is the responsibility of the user to obtain and use a shielded equipment interface cable with this device. If this equipment has more than one interface connector, do not leave cables connected to unused interfaces. Changes or modifications not expressly approved by the manufacturer could void the users authority to operate the equipment.

For Canadian Users

This Class B digital apparatus meets all requirements of the Canadian Interference-Causing Equipment Regulations.

Cet appareil numrique de la classe B respecte toutes les exigences du Rglement sur le materiel brouilluer du Canada.

124

Declaration of Conformity We: Epson America, Inc. Located at: MS 3-13

3840 Kilroy Airport Way Long Beach, CA 90806

Telephone: (562) 290-5254

Declare under sole responsibility that the product identified herein, complies with Part 15 of the FCC rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.

Trade Name: Epson Type of Product: Ensemble HD Complete Home Cinema System Model: ELPHC100/ELPHC200

Epson America, Inc. Limited Warranty

Epson Ensemble HD Home Theater System

What Is Covered: Epson America, Inc. (Epson) warrants to the original retail purchaser of the Epson Ensemble Home Theater System (which includes the projector, screen, speakers, sub-woofer, AV controller, projector cradle, projector mount, and wiring package) covered by this limited warranty statement that the System, if purchased new and operated only in the United States or Canada, will be free from defects in workmanship and materials for a period of two (2) years from the date of original purchase. This limited warranty applies only to the System and not to the projector lamp, which carries a ninety (90) day warranty from the date of original purchase.

What Epson Will Do to Correct Problems: Should any element of the System or the lamp prove defective during the limited warranty period, please call the Epson ConnectionSM at (800) 637-7661 + PIN or (562) 276-4394 in the U.S. and (905) 709-3839 in Canada for warranty instructions and return authorization. When you call, please be prepared to provide the service technician with the product model and the product serial number (located on the back of the screen weight bar), along with proof of the date of original purchase. The service technician will provide telephone diagnostics to determine whether your unit needs service, and detailed instructions if it is determined that service is needed. When Epson authorizes an exchange for the defective unit, Epson will ship a replacement product to you, freight prepaid, so long as you use an address in Canada or the U.S. (excluding Puerto Rico and U.S. Possessions). Shipments to other locations will be made freight collect. You are responsible for securely packaging the defective unit and returning it to Epson within ten (10) working days of receipt of the replacement. Epson requires a debit or a credit card number to secure the cost of the replacement product in the event that you fail to return the defective one. When service involves the exchange of a unit or its parts, the items replaced become the property of Epson. The exchanged product or part may be new or refurbished to the Epson standard of quality, and, at Epsons option, the replacement may be another model of like kind and quality. Epsons liability for replacement of the covered product will not exceed the original retail selling price of the covered product. The new items assume the remaining warranty period of the original product. If Epson chooses to replace a defective product or part, a replacement product or part will be shipped to you at no charge, but it is your responsibility to pay any labor costs for installation and removal.

125

What This Warranty Does Not Cover: This warranty covers only normal use of the product. Twenty-four-hour- per-day or other excessive continual use is not considered normal use. This warranty does not cover consumables (e.g., fuses or filters) other than lamps. This warranty is not transferable. Epson is not responsible for warranty service should the Epson label or logo or the rating label or serial number be removed. Epson is not responsible for warranty service should the product fail to be properly maintained or fail to function properly as a result of misuse, abuse, improper installation, neglect, improper shipping, damage caused by disasters such as fire, flood, and lightning, improper electrical current, software problems, interaction with non-Epson products, or service other than by an Epson Authorized Servicer. If a claimed defect cannot be identified or reproduced in service, you will be held responsible for costs incurred.

THE WARRANTY AND REMEDY PROVIDED ABOVE ARE EXCLUSIVE AND IN LIEU OF ALL OTHER EXPRESS OR IMPLIED WARRANTIES INCLUDING, BUT NOT LIMITED TO, THE IMPLIED WARRANTIES OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE. SOME LAWS DO NOT ALLOW THE EXCLUSION OF IMPLIED WARRANTIES. IF THESE LAWS APPLY, THEN ALL EXPRESS AND IMPLIED WARRANTIES ARE LIMITED TO THE WARRANTY PERIOD IDENTIFIED ABOVE. UNLESS STATED HEREIN, ANY STATEMENTS OR REPRESENTATIONS MADE BY ANY OTHER PERSON OR FIRM ARE VOID. IN THE EVENT THE REMEDIES ABOVE FAIL, EPSONS ENTIRE LIABILITY SHALL BE LIMITED TO A REFUND OF THE PRICE PAID FOR THE EPSON PRODUCT COVERED BY THIS LIMITED WARRANTY. EXCEPT AS PROVIDED IN THIS WRITTEN WARRANTY, NEITHER EPSON AMERICA, INC. NOR ITS AFFILIATES SHALL BE LIABLE FOR ANY LOSS, INCONVENIENCE, OR DAMAGE, INCLUDING DIRECT, SPECIAL, INCIDENTAL, OR CONSEQUENTIAL DAMAGES, RESULTING FROM THE USE OR INABILITY TO USE THE EPSON PRODUCT, WHETHER RESULTING FROM BREACH OF WARRANTY OR ANY OTHER LEGAL THEORY.

In Canada, warranties include both warranties and conditions.

Some jurisdictions do not allow limitations on how long an implied warranty lasts and some jurisdictions do not allow the exclusion or limitation of incidental or consequential damages, so the above limitations and exclusions may not apply to you. This warranty gives you specific legal rights, and you may also have other rights, which vary from jurisdiction to jurisdiction.

To find the Epson Authorized Reseller nearest you, visit our website at: www.epson.com.

To find the Epson Customer Care Center nearest you, visit epson.com/support.

You can also write to:

Epson America, Inc., P.O. Box 93012, Long Beach, CA 90809-3012.

126

127

Index

A Advanced features, remote control, 71 to 83 Aspect ratio, selecting, 43 to 44 Audio equipment

connecting, 36 controlling, 15 to 17, 39 to 40 linking to video sources, 34 to 35 problems, 64 setting up remote control for, 36 to 39, 85 to 117

Audio files, playing, 26 to 28 Audio menu, 46 to 47 AV controller

audio files, playing, 26 to 28 buttons, 16 CD, playing, see CD player cleaning, 54 connecting external components, 31 to 36 defaults, resetting, 51 DVD playing, see DVD player headphone connection, 17 MP3 player, using, 28 radio, playing, 29 to 30 specifications, 122 tape deck, using, 29, 36 turning on, 13 volume, 17, 36

B Backlight, LCD screen, 71 Bass, 46 Batteries, remote control, 59 Black drop, screen, 54 Brightness, 45

C CD player

connecting external, 36 controlling CD, 24 to 25 loading CD, 23

Channels, selecting, 16 Cleaning system, 53 to 54 Cloning commands, remote control, 72, 74 Code lists, remote control, 85 to 117 Color intensity, 45

Color Mode, 42 to 43 Command repeaters, using, 81 to 82 Commands, remote control

cloning, 74 editing, 75 to 77 erasing, 79 to 80 learning, 72 to 74 macros, 77 to 80

Component video, 32 to 33 Contrast

image, 45 LCD screen, adjusting, 72

Copyright notice, 123 CVBS (composite video), 32 to 33

D Defaults, resetting

AV controller, 51 remote control, 83

Device names, editing, 75 to 77 Disc

inserting, 19 specifications, 119

Distance, speakers, 46 DVD player

controlling, 15 to 17 inserting disc, 19 language, selecting, 22, 49 playing movie, 20 to 22 problems, 67 subtitles, selecting, 22

E Enclosure, projector, 56 to 57 Ensemble HD system

AV controller, see AV controller cleaning, 53 to 54 problems, 61 to 69 screen, see Screen turning on, 13 to 14

Epson PrivateLine Support, 69

Epson technical support, 69 External components

128

cleaning, 54 connecting, 31 to 36 controlling, 15 to 17, 39 to 40 problems, 68 setting up remote control for, 36 to 39, 85 to 117 turning on, 14

F FCC statement, 123 Focusing image, 57

H HDMI, 32 to 33, 45 Headphones, 17 Help, Epson, 69

I Image

aspect ratio, 43 to 44 colors, 42 to 43 focusing, 57 positioning, 56 to 57 problems, 62 to 63 quality, 45 resizing, 43 to 44, 57

L Lamp, projector, 58 Language

DVD tracks, 22, 49 menu, 49 subtitles, 22, 49

LCD screen, remote control backlight, adjusting, 71 contrast, adjusting, 72 using, 12 to 13, 39

Learning commands, remote control, 72 to 74 Lens

cleaning, 53 shift dial, 57

Light projector, 58 remote control, 12, 59

Linking audio/video sources, 34 to 35

M Macros, remote control, 77 to 80 Maintenance, 53 to 59

Menus Audio, 46 to 47 Color Mode, 42 to 43 Language, 49 Parental Controls, 50 to 51 Preference, 48, 50 to 51 Reset, 51 Source Assign, 34 Test Tone, 46 to 47 using system, 41 to 42 video, 45

Midnight Mode, 17, 48 Movies, watching, 19 to 22 MP3 player, 28 Music, playing, 23 to 30

N Names, editing devide, 75 to 77 Noise Reduction, 45

O Operation

problems, 61 to 62 OSD button, 35, 47

P Pages, remote control, 78 to 79 Parental Controls, 50 to 51 Password, 50 to 51 Picture

colors, 42 to 43 positioning, 56 to 57 problems, 62 to 63 quality, 45

Preference menu, 48, 50 to 51 PrivateLine Support, 69 Problems

DVD player, 67 Ensemble HD system, 61 to 69 external component, 68 operation, 61 to 62 picture, 62 to 63 radio, 67 remote control, 66 screen, 65 sound, 64 technical support, 69

Projector

129

cleaning, 53 enclosure, 56 to 57 lamp, checking, 58 lens shift dial, 57 lights, 58 menus, 58 remote control, 56, 59

Punch-through, remote control, 80 to 81

R Radio

playing, 29 to 30 problems, 67

Ratings, 51 Recalling codes, remote control, 86 Remote control

advanced features, 71 to 83 aiming, 12 batteries, 59 cloning commands, 72, 74 code lists, 85 to 117 command repeaters, using, 81 to 82 controlling components, 15 to 16, 39 to 40 defaults, resetting, 83 editing commands, 75 to 77 erasing commands, 79 to 80 LCD screen, see LCD screen, remote control learning commands, 72 to 74 lighting, 12, 59 macros, 77 to 80 pages, adding/hiding, 78 to 79 problems, 66 projector, 56, 59 punch-through feature, 80 to 81 recalling codes, 86 RF base station, using optional, 81 to 82 sensor on screen, 65 setting up for components, 36 to 39, 85 to 117 specifications, 120 volume, controlling, 17

Reset menu, 51 RF base station, using optional, 81 to 82

S Safety instructions, 3 to 4 Screen

adjusting position, 54 to 55 black drop length, 54

cleaning, 53 controlling, 15 lowering, 13 to 15 problems, 65 raising, 13 to 15 sensor, remote control, 65 specifications, 120

Sensor, remote control, 65 Service, 69 Sharpness, 45 Shift dial, projector lens, 57 Sound, see Audio equipment or Speakers Source Assign menu, 34, 45 Speakers

distance, 46 problems, 64 specifications, 120 to 121 surround, see Surround speakers volume, 17

Specifications AV controller, 122 discs, 119 remote control, 120 screen, 120 subwoofer, 121 surround speakers, 121

Stereo, 47 Subtitles, selecting, 22 Subwoofer

problems, 64 specifications, 121 volume, 17

Support, technical, 69 Surround Sound format, 47 Surround speakers

specifications, 121 volume, 46

S-Video, 32 to 33

T Tape deck, external, 29, 36 Technical specifications, 119 to 122 Test Tone menu, 46 to 47 Tint, 45 Treble, 46 Troubleshooting, 61 to 69 Turning on system, 13 to 14

130

V Video equipment

connecting, 32 to 33 controlling, 15 to 17, 39 to 40 linking to audio sources, 34 to 35 setting up remote control for, 36 to 39, 85 to 117

Video menu, 45 Voice, 46 Volume

controlling, 17, 36, 46 Midnight Mode, 17, 48 testing, 46 to 47

W Warning light, projector, 58

Z Zooming, 57

Manualsnet FAQs

If you want to find out how the Ensemble HD 8500 Epson works, you can view and download the Epson Ensemble HD 8500 User's Guide on the Manualsnet website.

Yes, we have the User's Guide for Epson Ensemble HD 8500 as well as other Epson manuals. All you need to do is to use our search bar and find the user manual that you are looking for.

The User's Guide should include all the details that are needed to use a Epson Ensemble HD 8500. Full manuals and user guide PDFs can be downloaded from Manualsnet.com.

The best way to navigate the Epson Ensemble HD 8500 User's Guide is by checking the Table of Contents at the top of the page where available. This allows you to navigate a manual by jumping to the section you are looking for.

This Epson Ensemble HD 8500 User's Guide consists of sections like Table of Contents, to name a few. For easier navigation, use the Table of Contents in the upper left corner.

You can download Epson Ensemble HD 8500 User's Guide free of charge simply by clicking the “download” button in the upper right corner of any manuals page. This feature allows you to download any manual in a couple of seconds and is generally in PDF format. You can also save a manual for later by adding it to your saved documents in the user profile.

To be able to print Epson Ensemble HD 8500 User's Guide, simply download the document to your computer. Once downloaded, open the PDF file and print the Epson Ensemble HD 8500 User's Guide as you would any other document. This can usually be achieved by clicking on “File” and then “Print” from the menu bar.