Contents

Epson PowerLite 97 Quick Setup PDF

1 of 4
1 of 4

Summary of Content for Epson PowerLite 97 Quick Setup PDF

Quick Setup Before using the projector, make sure you read the safety instructions in the online Users Guide.

Connect the projector Choose from the following connections. See the sections below or the online Users Guide for details.

Computer

S-Video Video L R

VGA cable

HDMI cable

Audio cable

USB cable

USB port

Connect the square end of a USB cable to the projectors USB-B (square) port. Connect the flat end of the cable to any USB port on your computer.

Windows XP or later: After turning on the projector, follow the on-screen instructions to install the Epson USB Display software (EMP_UDSE.EXE; only on first connection). If the software screen does not display automatically, open My Computer or Computer, then double-click EPSON_PJ_UD.

Mac OS X 10.5.1 or higher: After turning on the projector, the setup folder for USB Display appears in the Finder. Double-click USB Display Installer and follow the on-screen instructions to install the Epson USB Display software (only on first connection).

Computer port

Connect one end of a VGA cable to the projectors Computer1 or Computer2 port, and the other end to your computers monitor port. If you are using a laptop, switch it to external display (see Troubleshooting). You can also connect an audio cable.

HDMI port

Connect one end of an HDMI cable to the projectors HDMI port and the other end to an HDMI port on your computer.

Wired network You can connect the projector to your network using an Ethernet cable.

S-Video Video L R

See Project over a wired network for instructions.

Video device Connect up to 5 video devices and use the Source Search button on the projector or remote control to switch between them.

S-Video Video L R

Audio cable

Component video to VGA cable

S-Video cable

Audio cable

HDMI cable

RCA video cable

Camera, USB device, or Epson DC-06 document camera Connect a digital camera, USB flash drive, USB storage device, or Epson DC-06 document camera to the projectors USB-A (flat) port.

S-Video Video L R

USB cable

If you connect a digital camera, USB flash drive, or USB storage device, you can use the projectors PC Free feature. See the online Users Guide for details.

External monitor, external speakers, and microphone You can also connect an external monitor, external speakers, or a microphone to your projector to enhance your presentations. See the online Users Guide for details.

Turn on your equipment 1 Turn on your computer or video source.

2 Plug in the projector. The power light on the projector turns blue.

3 Open the A/V Mute slide all the way.

4 Press the power button on the projector or remote control. The projector beeps, and the Status light flashes blue and then stays on.

Note: To shut down the projector, press the power button twice, then unplug it. You dont have to wait for the projector to cool down.

5 The default language of the menu system is English. To select another language, press the Menu button on the projector or remote control. Select Extended and press . Select Language and press . Select your language and press . Press the Menu button to exit the menu system.

Adjust the image 1 If you dont see an image, press the Source Search button on the

projector or the remote control to select the image source.

Note: If you still see a blank screen or have other display problems, see the troubleshooting tips on the back of this sheet.

2 To raise the image, press the foot release button and lift the front of the projector. Release the button to lock the foot in position.

3 Turn the zoom ring to enlarge or reduce the image.

4 Turn the focus ring to sharpen the image.

5 If your image looks like or , you may have placed the projector off to one side of the screen at an angle. Place the projector directly in front of the center of the screen, facing the screen squarely. If you cant move the projector, use the horizontal keystone slider to correct the image.

6 Your projector automatically adjusts images that look like or , but if necessary you can press the or button on the projector to correct it.

Using the remote control Make sure the batteries are installed as shown (two AA batteries).

Choose which source to display

Turn projector on and off

Access projector menus

Turn off projector display Get solutions to

common problems

Navigate projector menus

For more information on using the remote control, see the online Users Guide.

Project wirelessly Follow the steps here to connect the projector over a wireless network. You will need the optional wireless LAN module (part number V12H418P12).

1 To install the wireless LAN module, first remove the screw as shown.

2 Connect the wireless LAN module to the USB-A (flat) port.

3 To configure your projector for wireless projection, do one of the following:

If youre using the optional Quick Wireless Connection USB key (Windows only, part number V12H005M09), press theLAN button on the remote control. When you see SSID and IP address information on the screen, remove the wireless LAN module and connect the key to the projectors USB-A port. Look for the displayed message, remove the key, and connect it to a USB port on your computer. Follow the on-screen instructions to install the driver, then reconnect the wireless LAN module to the projectors USB-A port. For details, see the online Users Guide.

If youre not using the key, continue with the steps on the next page.

PowerLite 97/98/99W/955W/965

*412613300* *412613300*

Quick Setup Before using the projector, make sure you read the safety instructions in the online Users Guide.

Connect the projector Choose from the following connections. See the sections below or the online Users Guide for details.

Computer

S-Video Video L R

VGA cable

HDMI cable

Audio cable

USB cable

USB port

Connect the square end of a USB cable to the projectors USB-B (square) port. Connect the flat end of the cable to any USB port on your computer.

Windows XP or later: After turning on the projector, follow the on-screen instructions to install the Epson USB Display software (EMP_UDSE.EXE; only on first connection). If the software screen does not display automatically, open My Computer or Computer, then double-click EPSON_PJ_UD.

Mac OS X 10.5.1 or higher: After turning on the projector, the setup folder for USB Display appears in the Finder. Double-click USB Display Installer and follow the on-screen instructions to install the Epson USB Display software (only on first connection).

Computer port

Connect one end of a VGA cable to the projectors Computer1 or Computer2 port, and the other end to your computers monitor port. If you are using a laptop, switch it to external display (see Troubleshooting). You can also connect an audio cable.

HDMI port

Connect one end of an HDMI cable to the projectors HDMI port and the other end to an HDMI port on your computer.

Wired network You can connect the projector to your network using an Ethernet cable.

S-Video Video L R

See Project over a wired network for instructions.

Video device Connect up to 5 video devices and use the Source Search button on the projector or remote control to switch between them.

S-Video Video L R

Audio cable

Component video to VGA cable

S-Video cable

Audio cable

HDMI cable

RCA video cable

Camera, USB device, or Epson DC-06 document camera Connect a digital camera, USB flash drive, USB storage device, or Epson DC-06 document camera to the projectors USB-A (flat) port.

S-Video Video L R

USB cable

If you connect a digital camera, USB flash drive, or USB storage device, you can use the projectors PC Free feature. See the online Users Guide for details.

External monitor, external speakers, and microphone You can also connect an external monitor, external speakers, or a microphone to your projector to enhance your presentations. See the online Users Guide for details.

Turn on your equipment 1 Turn on your computer or video source.

2 Plug in the projector. The power light on the projector turns blue.

3 Open the A/V Mute slide all the way.

4 Press the power button on the projector or remote control. The projector beeps, and the Status light flashes blue and then stays on.

Note: To shut down the projector, press the power button twice, then unplug it. You dont have to wait for the projector to cool down.

5 The default language of the menu system is English. To select another language, press the Menu button on the projector or remote control. Select Extended and press . Select Language and press . Select your language and press . Press the Menu button to exit the menu system.

Adjust the image 1 If you dont see an image, press the Source Search button on the

projector or the remote control to select the image source.

Note: If you still see a blank screen or have other display problems, see the troubleshooting tips on the back of this sheet.

2 To raise the image, press the foot release button and lift the front of the projector. Release the button to lock the foot in position.

3 Turn the zoom ring to enlarge or reduce the image.

4 Turn the focus ring to sharpen the image.

5 If your image looks like or , you may have placed the projector off to one side of the screen at an angle. Place the projector directly in front of the center of the screen, facing the screen squarely. If you cant move the projector, use the horizontal keystone slider to correct the image.

6 Your projector automatically adjusts images that look like or , but if necessary you can press the or button on the projector to correct it.

Using the remote control Make sure the batteries are installed as shown (two AA batteries).

Choose which source to display

Turn projector on and off

Access projector menus

Turn off projector display Get solutions to

common problems

Navigate projector menus

For more information on using the remote control, see the online Users Guide.

Project wirelessly Follow the steps here to connect the projector over a wireless network. You will need the optional wireless LAN module (part number V12H418P12).

1 To install the wireless LAN module, first remove the screw as shown.

2 Connect the wireless LAN module to the USB-A (flat) port.

3 To configure your projector for wireless projection, do one of the following:

If youre using the optional Quick Wireless Connection USB key (Windows only, part number V12H005M09), press theLAN button on the remote control. When you see SSID and IP address information on the screen, remove the wireless LAN module and connect the key to the projectors USB-A port. Look for the displayed message, remove the key, and connect it to a USB port on your computer. Follow the on-screen instructions to install the driver, then reconnect the wireless LAN module to the projectors USB-A port. For details, see the online Users Guide.

If youre not using the key, continue with the steps on the next page.

PowerLite 97/98/99W/955W/965

*412613300* *412613300*

6 Select the Wired LAN menu and press .

7 Choose IP Settings and press .

8 If your network assigns addresses automatically, turn on the DHCP setting. If not, turn off the DHCP setting and enter the projectors IP Address, Subnet Mask, and Gateway Address, as needed. Then press Esc.

9 To prevent the IP address from appearing on the network standby screen, set the IP Address Display setting to Off.

10 When you are finished, select Complete and press , then press again to save your settings.

11 Press the Menu button to exit the menu system.

12 See Install network software for additional instructions.

Install network software Computer Install the EasyMP Network Projection software on each computer that will project over the network. Use the CD labeled Epson Projector Software to install the program.

For instructions on installing and using your network software, click the icon on your desktop to access the online EasyMP Network Projection Operation Guide (requires an Internet connection). If you dont see the EasyMP Network Projection Guide icon, you can install it from the projector CD or go to the Epson website, as described on the right.

To monitor and control your projector over the network, download and install the EasyMP Monitor software and manual from the Epson support web site. You can install a link to the downloads page from the projector CD or go to the Epson website, as described on the right.

Mobile device To project from an iOS or Android device, download and install the Epson iProjection app. Visit www.epson.com/projectorapp (U.S.) or www.epson.ca/projectorapp (Canada) for more information.

Troubleshooting If you see a blank screen or the No signal message after turning on your computer or video device, check the following:

Make sure the Status light on the projector is blue and not flashing, and the A/V Mute slide is open.

Press the Source Search button on the projector or the remote control to switch to the correct image source, if necessary.

If youre using a Windows laptop, press the function key on your keyboard that lets you display on an external monitor. It may be labeled CRT/LCD or have an icon such as . You may have to hold down the Fn key while pressing it (such as Fn + F7). Wait a moment for the display to appear.

4 Attach the wireless LAN module cover and secure it using the screw you removed.

5 Press the Menu button on the remote control, select the Network menu, and press .

6 Choose Network Configuration and press .

7 Select the Wireless LAN menu and press .

8 Choose Connection Mode, press , select Quick (for a direct connection to a computer, tablet, or smartphone) or Advanced (for a connection to a router or access point), then press again. When youre finished, press Esc to return to the Wireless LAN menu.

9 If you chose the Advanced connection mode, select SSID, press and enter your network name (SSID) on the screen that appears.

To select a number or character, use the arrow buttons on the remote control to highlight it, then press .

To switch between uppercase and lowercase letters, select CAPS and press .

To change the displayed symbols, select SYM1 or SYM2 and press .

When youre finished entering the SSID, select Finish and press .

10 If you chose the Advanced connection mode, select IP settings and press .

If your network assigns addresses automatically, turn on DHCP. If not, turn off DHCP and enter the projectors IP Address, Subnet Mask, and Gateway Address, as needed.

To enter numbers, use the arrow buttons on the remote control to highlight a number, then press the button. When youre finished entering an address, highlight Finish, then press . Press Esc.

EPSON, EasyMP, and PowerLite are registered trademarks, Epson iProjection is a trademark, and EPSON Exceed Your Vision is a registered logomark of Seiko Epson Corporation. PrivateLine is a registered trademark of Epson America, Inc.

Mac and Mac OS are trademarks of Apple Inc., registered in the U.S. and other countries.

General Notice: Other product names used herein are for identification purposes only and may be trademarks of their respective owners. Epson disclaims any and all rights in those marks.

This information is subject to change without notice.

2013 Epson America, Inc. 9/13 Printed in XXXXXX CPD-39732R1

11 To prevent the SSID and IP address from appearing on the network standby screen, set the SSID Display and IP Address Display settings to Off.

12 When youre finished selecting settings in the Wireless LAN menu, press Esc.

13 If you are connecting the projector to a secure network, select the Security menu and press . Then select settings and pressEsc when youre finished.

14 Select Complete and press , then select Yes and press again to save your settings.

15 See Install network software for additional instructions.

Project over a wired network Follow the steps here to configure your projector for your wired network using the projectors menu system.

1 Plug in and turn on the projector.

2 Press the Menu button on the remote control, select the Network menu, and press .

3 Select Network Configuration and press .

4 Select the Basic menu and press .

5 Select the Projector Name setting and enter a name (up to 16 characters long) to identify your projector over the network.

Use the displayed keyboard to enter characters. Press the arrow buttons on the remote control to highlight the characters and press to select them.

Note: See the online Users Guide for information on adding passwords.

If youre using a Mac laptop, open System Preferences and select Displays. Select the Display or Color LCD option if necessary, then click the Arrange or Arrangement tab, and select the Mirror Displays checkbox.

Where to get help Manuals For more information about using the projector, click the icons on your desktop to access the online manuals (requires an Internet connection). If you dont have icons to the manuals, you can install them from the projector CD or go to the Epson website, as described below.

Telephone support services To use the Epson PrivateLine Support service, call (800) 637-7661. This service is available for the duration of your warranty period. You may also speak with a support specialist by calling (562) 276-4394 (U.S.) or (905) 709-3839 (Canada).

Support hours are 6 am to 8 pm, Pacific Time, Monday through Friday, and 7 am to 4 pm, Pacific Time, Saturday. Days and hours of support are subject to change without notice. Toll or long distance charges may apply.

Internet support Visit www.epson.com/support (U.S.) or www.epson.ca/support (Canada) for solutions to common problems. You can download utilities and documentation, get FAQs and troubleshooting advice, or e-mail Epson.

Registration Register today to get product updates and exclusive offers. You can use the CD included with your projector or register online at www.epson.com/webreg.

Optional accessories For a list of optional accessories, see the online Users Guide.

You can purchase screens or other accessories from an Epson authorized reseller. To find the nearest reseller, call 800-GO-EPSON (800-463-7766). Or you can purchase online at www.epsonstore.com (U.S. sales) or www.epson.ca (Canadian sales).

6 Select the Wired LAN menu and press .

7 Choose IP Settings and press .

8 If your network assigns addresses automatically, turn on the DHCP setting. If not, turn off the DHCP setting and enter the projectors IP Address, Subnet Mask, and Gateway Address, as needed. Then press Esc.

9 To prevent the IP address from appearing on the network standby screen, set the IP Address Display setting to Off.

10 When you are finished, select Complete and press , then press again to save your settings.

11 Press the Menu button to exit the menu system.

12 See Install network software for additional instructions.

Install network software Computer Install the EasyMP Network Projection software on each computer that will project over the network. Use the CD labeled Epson Projector Software to install the program.

For instructions on installing and using your network software, click the icon on your desktop to access the online EasyMP Network Projection Operation Guide (requires an Internet connection). If you dont see the EasyMP Network Projection Guide icon, you can install it from the projector CD or go to the Epson website, as described on the right.

To monitor and control your projector over the network, download and install the EasyMP Monitor software and manual from the Epson support web site. You can install a link to the downloads page from the projector CD or go to the Epson website, as described on the right.

Mobile device To project from an iOS or Android device, download and install the Epson iProjection app. Visit www.epson.com/projectorapp (U.S.) or www.epson.ca/projectorapp (Canada) for more information.

Troubleshooting If you see a blank screen or the No signal message after turning on your computer or video device, check the following:

Make sure the Status light on the projector is blue and not flashing, and the A/V Mute slide is open.

Press the Source Search button on the projector or the remote control to switch to the correct image source, if necessary.

If youre using a Windows laptop, press the function key on your keyboard that lets you display on an external monitor. It may be labeled CRT/LCD or have an icon such as . You may have to hold down the Fn key while pressing it (such as Fn + F7). Wait a moment for the display to appear.

4 Attach the wireless LAN module cover and secure it using the screw you removed.

5 Press the Menu button on the remote control, select the Network menu, and press .

6 Choose Network Configuration and press .

7 Select the Wireless LAN menu and press .

8 Choose Connection Mode, press , select Quick (for a direct connection to a computer, tablet, or smartphone) or Advanced (for a connection to a router or access point), then press again. When youre finished, press Esc to return to the Wireless LAN menu.

9 If you chose the Advanced connection mode, select SSID, press and enter your network name (SSID) on the screen that appears.

To select a number or character, use the arrow buttons on the remote control to highlight it, then press .

To switch between uppercase and lowercase letters, select CAPS and press .

To change the displayed symbols, select SYM1 or SYM2 and press .

When youre finished entering the SSID, select Finish and press .

10 If you chose the Advanced connection mode, select IP settings and press .

If your network assigns addresses automatically, turn on DHCP. If not, turn off DHCP and enter the projectors IP Address, Subnet Mask, and Gateway Address, as needed.

To enter numbers, use the arrow buttons on the remote control to highlight a number, then press the button. When youre finished entering an address, highlight Finish, then press . Press Esc.

EPSON, EasyMP, and PowerLite are registered trademarks, Epson iProjection is a trademark, and EPSON Exceed Your Vision is a registered logomark of Seiko Epson Corporation. PrivateLine is a registered trademark of Epson America, Inc.

Mac and Mac OS are trademarks of Apple Inc., registered in the U.S. and other countries.

General Notice: Other product names used herein are for identification purposes only and may be trademarks of their respective owners. Epson disclaims any and all rights in those marks.

This information is subject to change without notice.

2013 Epson America, Inc. 9/13 Printed in XXXXXX CPD-39732R1

11 To prevent the SSID and IP address from appearing on the network standby screen, set the SSID Display and IP Address Display settings to Off.

12 When youre finished selecting settings in the Wireless LAN menu, press Esc.

13 If you are connecting the projector to a secure network, select the Security menu and press . Then select settings and pressEsc when youre finished.

14 Select Complete and press , then select Yes and press again to save your settings.

15 See Install network software for additional instructions.

Project over a wired network Follow the steps here to configure your projector for your wired network using the projectors menu system.

1 Plug in and turn on the projector.

2 Press the Menu button on the remote control, select the Network menu, and press .

3 Select Network Configuration and press .

4 Select the Basic menu and press .

5 Select the Projector Name setting and enter a name (up to 16 characters long) to identify your projector over the network.

Use the displayed keyboard to enter characters. Press the arrow buttons on the remote control to highlight the characters and press to select them.

Note: See the online Users Guide for information on adding passwords.

If youre using a Mac laptop, open System Preferences and select Displays. Select the Display or Color LCD option if necessary, then click the Arrange or Arrangement tab, and select the Mirror Displays checkbox.

Where to get help Manuals For more information about using the projector, click the icons on your desktop to access the online manuals (requires an Internet connection). If you dont have icons to the manuals, you can install them from the projector CD or go to the Epson website, as described below.

Telephone support services To use the Epson PrivateLine Support service, call (800) 637-7661. This service is available for the duration of your warranty period. You may also speak with a support specialist by calling (562) 276-4394 (U.S.) or (905) 709-3839 (Canada).

Support hours are 6 am to 8 pm, Pacific Time, Monday through Friday, and 7 am to 4 pm, Pacific Time, Saturday. Days and hours of support are subject to change without notice. Toll or long distance charges may apply.

Internet support Visit www.epson.com/support (U.S.) or www.epson.ca/support (Canada) for solutions to common problems. You can download utilities and documentation, get FAQs and troubleshooting advice, or e-mail Epson.

Registration Register today to get product updates and exclusive offers. You can use the CD included with your projector or register online at www.epson.com/webreg.

Optional accessories For a list of optional accessories, see the online Users Guide.

You can purchase

Manualsnet FAQs

If you want to find out how the PowerLite 97 Epson works, you can view and download the Epson PowerLite 97 Quick Setup on the Manualsnet website.

Yes, we have the Quick Setup for Epson PowerLite 97 as well as other Epson manuals. All you need to do is to use our search bar and find the user manual that you are looking for.

The Quick Setup should include all the details that are needed to use a Epson PowerLite 97. Full manuals and user guide PDFs can be downloaded from Manualsnet.com.

The best way to navigate the Epson PowerLite 97 Quick Setup is by checking the Table of Contents at the top of the page where available. This allows you to navigate a manual by jumping to the section you are looking for.

This Epson PowerLite 97 Quick Setup consists of sections like Table of Contents, to name a few. For easier navigation, use the Table of Contents in the upper left corner.

You can download Epson PowerLite 97 Quick Setup free of charge simply by clicking the “download” button in the upper right corner of any manuals page. This feature allows you to download any manual in a couple of seconds and is generally in PDF format. You can also save a manual for later by adding it to your saved documents in the user profile.

To be able to print Epson PowerLite 97 Quick Setup, simply download the document to your computer. Once downloaded, open the PDF file and print the Epson PowerLite 97 Quick Setup as you would any other document. This can usually be achieved by clicking on “File” and then “Print” from the menu bar.