Epson PowerLite 737c Quick Setup PDF

2 Turn the focus ring to sharpen the image.

Turn the zoom ring to reduce or enlarge the image.

3 If your image looks like or , youve placed the projector off to one side of the screen at an angle. Place it directly in front of the screen, facing the screen squarely.

4 If your image looks like or , press the or buttons on the projector to correct it.

EPSON PowerLite 737c/745c

Quick Setup

1 Turn On Your Equipment

1 Connect the power cord to the back of the projector and plug the other end into an electrical outlet.

2 Remove the lens cover.

3 Remove the battery cover on the remote control. Locate the batteries that came with the projector and insert them as shown. Then replace the battery cover.

4 To turn the projector on, press the red Power button on the projector or the remote control. The projector beeps once, and the projectors Power light flashes green and then stays on.

CAUTION: Before unplugging the projector...

Shut the projector down properly:

1. Press the Power button twice. Let the projector cool while the Power light flashes orange (about 20 seconds).

2. Once the light stops flashing and the projector beeps, its safe to unplug the projector.

How do you want to get images to the projector?

To connect to a notebook, see If connecting to a notebook below.

To project over an 802.11g/b network, see If projecting wirelessly on the back of this sheet.

You must have installed the projectors EasyMPTM

software and configured your projector and computer before you can project wirelessly. See your Users Guide for instructions.

To give a presentation stored on a memory card, see Chapter 5 in your Users Guide.

If connecting to a notebook... 1 Make sure youve turned on the projector and adjusted the image

as described in sections 1 and 2.

2 Locate the computer cable that came with the projector. Connect one end to the projectors blue Computer/Component Video port.

Connect the other end to your notebooks video-out port or monitor port. If you cant connect the cable to your

PowerBook, you may need to use an adapter. See your PowerLite 737c/745c Users Guide for instructions.

3 Press the Source Search button on the projector until your computer image is displayed.

3 Choose a Presentation Method

1 To raise the image, press the blue foot release button for the front adjustable foot and lift the front. Release the button to lock the foot in position.

2 Adjust the Image

Turn over

Zoom

Focus

Computer cable

Wireless card

Once the card is inserted, the projector displays a screen like this:

4 Windows: From the Start menu, select EMP NS Connection.

Macintosh OS X: Double-click the EMP NS Connection icon in your Applications folder.

5 If you see this screen, select the name and IP address for your computers 802.11g or 802.11b wireless card and click OK.

You see this screen:

If the connection is working properly, you see your projector listed. If you dont see your projector listed, restart your computer. If it still doesnt appear, see the Users Guide for help.

6 Once the name of your projector appears, select it and click Connect.

7 If you see a message asking for a keyword, enter the four digits that appear on the EasyMP Network Screen and click OK. (See the screen at the top of this column to locate the projector keyword.)

You see the image on your monitor transmitted to the projector, and a floating control bar appears on the computer screen:

8 When youre done with your presentation, click Disconnect on the control bar.

Epson is a registered trademark and EasyMP is a trademark of Seiko Epson Corporation. PowerLite and PrivateLine are registered trademarks of Epson America, Inc.

General Notice: Other product names are for identification purposes only and may be trademarks of their respective owners. Epson disclaims any and all rights in those marks.

2005 Epson America, Inc. 1/05 CPD-19398 Printed in XXXXXXXXX

Click here to minimize

Where To Get Help Telephone Support Services To use the Epson PrivateLine Support service, call (800) 637-7661 and enter the PIN on the Epson PrivateLine Support card included in your Start Here kit. This service is available 6 AM to 6 PM, Pacific Time, Monday through Friday, for the duration of your warranty period. You may also speak with a projector support specialist by dialing one of these numbers:

U.S.: (562) 276-4394, 6 AM to 6 PM, Pacific Time, Monday through Friday Canada: (905) 709-3839, 6 AM to 6 PM, Pacific Time, Monday through Friday

Toll or long distance charges may apply.

Electronic Support Services Epson provides assistance through electronic support services 24 hours a day at http://support.epson.com. For tips, templates, and training for developing successful presentations go to http://www.presentersonline.com.

4 If you see a blank screen or you dont see the image you are trying to project from your computer, make sure the Power light on the projector is green and not flashing, and the lens cover is off. If the screen is still blank, restart your notebook, or press the Source Search button on the projector again.

Windows: Hold down the Fn button on the keyboard and press the function key that lets you display on an external monitor. It may have an icon such as , or it may be labeled CRT/LCD.

5 If your projector and notebook dont display the same image, do the following:

Windows: Try using the CRT/LCD or function key, as described above. If this doesnt work, double-click Display in the Windows Control Panel. Make sure both the LCD screen and monitor port are enabled. (Allow a few seconds for the projector to sync up.) See your Windows online help for details.

Macintosh OS X: From the Apple menu, select System Preferences, then click Displays. Select the VGA Display or Color LCD dialog box, click the Arrangement (or Arrange) tab, and make sure Mirror Displays is checked.

Macintosh OS 9 or earlier: From the Apple menu, select Control Panels, then click Monitors or Monitors and Sound. Click the Arrange icon, then drag one monitor icon on top of the other; this lets you display on both the projection screen and the LCD screen. If this option isnt available, click the Monitor icon and select a Simulscan resolution.

6 If you see an image but its not displayed correctly, press the Auto button on the remote control to automatically readjust it.

If projecting wirelessly... Follow the steps in this section to project over an 802.11g or 802.11b wireless network from a computer running Windows 98, 2000, Me, XP, or Macintosh OS X 10.2.4 or above.

NOTE: You must have already installed the projectors EasyMP (EMP NS Connection) software and configured your projector and computer. See the Users Guide for instructions. Also, your computer must have an 802.11g or 802.11b network card or transmitter installed.

1 Make sure youve turned on the projector and adjusted the image as described in sections 1 and 2 on the front of this sheet.

2 Select EasyMP as the source by pressing the EasyMP button on the remote control.

3 Insert the Epson 802.11g card with the label facing upward, as shown. When fully inserted, the end of the card will protrude.

Click here

Drag one monitor icon onto the other

Click here

Make sure this is checked

Select