1 Remove the lens cover.
2 Connect the power cord to the projector and plug the other end into a grounded outlet.
The power light turns orange.
3 Turn on the other equipment connected to the projector.
4 Press the Power button on the projector or remote control. The power light flashes green, and the projector lamp comes on in about 15 seconds.
5 Start your video. If you have connected more than one video source, press the Computer or S-Video/Video button on the remote control to select the one you want to watch.
EPSON is a registered trademark of SEIKO EPSON CORPORATION. PowerLite is a registered trademark of Epson America, Inc. General Notice: Other product names used herein are for identification purposes only and may be trademarks of their respective owners. EPSON disclaims any and all rights in those marks. Copyright 2002 by Epson America, Inc. Printed in USA. 8/02
Multipurpose Entertainment Projector EPSON PowerLite 30c
CPD-14798
1 If you need to raise the image, press the foot adjust buttons and lift the front of the projector. Release the buttons to lock the feet in the position you want.
If you need to straighten the image, raise or lower an individual foot.
2 Rotate the focus ring to sharpen the image.
3 If your image is upside-down or reversed, you need to change the setting in the Advanced menu. Press the Menu button on the remote control and use the Enter button to choose the Advanced menu. Then select the correct setting for your setup.
4 If a computer is connected, do this after projection starts. Press the Menu button on the remote control, and use the Enter button to choose the Video menu. Go to the Input Signal option and change it to RGB.
5 If your image looks like or , first make sure the projector is facing the screen squarely. Then, if necessary, press the Keystone button on the projectors control panel until the image is corrected. (You also can do this using the projectors Setting menu. See your Users Guide on the CD-ROM.)
6 To select the best color mode, press the Color Mode button on the remote control repeatedly to move through the options.
7 To boost the projection quality of films, first attach the EPSON cinema filter to the lens. Then, press the Menu button on the remote control, go to the video menu, and change the EPSON Cinema Filter setting to ON.
See your Users Guide on the CD-ROM for more information about image adjustments.
Pull out the insulating tape that protrudes from the battery holder.
The remote control is ready for use.
3Set up the remote control
Turning off the projector 1 When youre finished using the projector, first turn off the video source.
2 Press the Power button on the projector or remote control.
3 When you see the confirmation message, press the Power button again. The power light flashes orange as the projector cools down.
Caution: Never unplug the projector when the power light is green or flashing orange.
4 Plug in and turn on
5 Adjust the image
No signal ( ? Help)
Power
S-Video/VideoComputer
Menu A/V Mute
E-Zoom
Freeze
Color Mode
Power
ESCAuto
Enter
Color Mode button
If you see a blank screen If you see a blank screen or the No Signal or Not Supported message, check the following:
Make sure the lens cover is off.
Make sure your power cord and video cable are connected securely.
If the power light is orange, press the Power button on either the remote control or the projectors control panel.
Make sure the correct input source is selected. On the remote control, press the Computer or S-Video/Video button to change the image source. Or, press the Source button on the control panel.
Try turning off your video equipment or computer and restarting it.
If mute mode is active, press the A/V Mute button on the remote control to resume projection.
If you connected a computer to the projector, it may be necessary to change the image signal to the projector. See Troubleshooting in your Users Guide on the CD-ROM.
S-Video/VideoComputer
Menu A/V Mute
E-Zoom
Freeze
Color Mode
Power
ESCAuto
en
