Epson 100 Idea Screen Instruction Manual PDF

INSTRUCTION MANUAL

100" IDEA Screen for Epson BrightLink Displays (16:9)

2020 Legrand AV Inc. 200028 3/20 Da-Lite is a registered trademark of Legrand AV Inc. All other brand names or marks are used for identification purposes and are trademarks of their respective owners. All patents are protected under existing designations. Other patents pending.

FOR YOUR IMAGE | legrandav.com

USA P 866.977.3901 E av.da-lite.support@legrand.com CANADA P 877.345.4329 E av.da-lite.support@legrand.com EMEA P +31 495 580 840 E av.emea.sales@legrand.com APAC P +852 2145 4099 E av.asia.sales@legrand.com

14028

2

Tools Required For Assembly

Phillips Screwdriver LevelRubber Mallet Measuring Tape

Hardware Provided

(7) #8 x 1/2" Screws

(1) Wall Bracket

(2) L-Brackets

Disclaimer

Legrand AV Inc. and its affiliated companies and subsidiaries (collectively, Legrand AV), intend to make this manual accurate and

complete. However, Legrand AV makes no claim that the information contained herein covers all details, conditions or variations, nor

does it provide for every possible contingency in connection with the installation or use of the products described herein. The content

herein is subject to change without notice or obligation of any kind. To the maximum extent permitted by applicable law, Legrand AV

makes no representation or warranty, expressed or implied, regarding the information contained herein. Furthermore, Legrand AV

assumes no responsibility for accuracy, completeness or sufficiency of the information contained in this document.

Da-Lite is a registered trademark of Legrand AV. All rights reserved.

Important Safety Instructions

1. Read and understand all instructions before using.

2. Failure to provide adequate structural strength for this component can result in serious personal injury or damage to equipment! It is the installers responsibility to make sure the structure to which this component is attached can support the weight of all equipment. Reinforce the structure as required before installing the component.

3. Use this projection screen only for its intended use as described in these instructions. Do not use attachments not recommended by the manufacturer.

Save These Instructions

3

Preparation

Note: Two people are required to assemble an IDEA Screen. To maintain optimal projected image geometry and screen alignment, a flat

and straight wall free from obstructions and angular distortions should be used.

Choose a clean work area for assembly using padded material or other soft, clean materials. The work area should be larger than the

overall screen size and directly in front of the location where the screen is to be installed.

Cleaning Everyday Cleaning: The supplied foam eraser can be used to clean marks on the screen surface made by everyday dry erase marker

usage. Do not use the Da-Lite spray cleaner in combination with the foam eraser.

Thorough Cleaning: For periodic full screen cleaning or to clean persistent marks from dry erase markers, use the supplied Da-Lite

spray cleaner and cleaning cloth. Use clean or dry sections of the microfiber cloth when erasing the screen. This is important to prevent

smearing on the screen while cleaning. To clean permanent markers and other unintentional marks on the surface, use the supplied

foam eraser or the Da-Lite spray cleaner and cleaning cloth.

4

DRAWING AND PART FILE MODEL NAME: TRAY_EXPLODED(EPSON)_NO_IR

MODEL LOCATION: S:\Engineering\Solidworks Files\EPSON IDEA\INSTRUCTIONS\

SHEETS: 1 OF 1 THE INFORMATION AND DESIGNS CONTAINED IN THIS DRAWING ARE CONFIDENTIAL

AND PROPRIETARY PROPERTY OF MILESTONE AV TECHNOLOGIES NEITHER THIS DESIGN NOR ANY INFORMATION CONTAINED IN THIS DRAWING MAY BE

REPRODUCED OR DISCLOSED TO OTHERS WITHOUT EXPRESS WRITTEN CONSENT OF MILESTONE AV TECHNOLOGIES.

THIS PRINT SUPERSEDES ANY PRINT DATED PRIOR TO:

PART NO:

262065/30/2014

REVISIONS REV. DESCRIPTION CHNGD BY: DATE: APPR'D BY:

TOLERANCES: DECIMAL:

.XX = .010 .XXX = .005

FRACTIONAL: = .015

ANGULAR: = 1

1:18 DRAWN BY:

ADW DATE:

4/16/2014 APP'D BY: DATE:

X.XXXX 1/19/2011 MATERIAL NO:

MULIT FINISH:

TYPE OF FINISH sw NAME: EXPLODED VIEW FOR INSTRUCTIONS

SCALE:

DA-LITE SCREEN CO. WARSAW, INDIANA, USA

PART NO: 26206

Assembly Instructions

1. Carefully unpack the unit and place on top of a clean work area.

The viewing surface must face up.

2. Center the marker tray to the bottom of the frame and attach it

with (3) of the provided #8 x 1/2" screws. Insert screws through the

tray into the groove (Figure 1).

#8 X 1/2" Screws

Figure 1

Marker Tray

Front

5 DRAWING AND PART FILE

MODEL NAME: MOUNTING EXPLODED(EPSON)_NO_IR

MODEL LOCATION: S:\Engineering\Solidworks Files\EPSON IDEA\INSTRUCTIONS\

SHEETS: 1 OF 1 THE INFORMATION AND DESIGNS CONTAINED IN THIS DRAWING ARE CONFIDENTIAL

AND PROPRIETARY PROPERTY OF MILESTONE AV TECHNOLOGIES NEITHER THIS DESIGN NOR ANY INFORMATION CONTAINED IN THIS DRAWING MAY BE

REPRODUCED OR DISCLOSED TO OTHERS WITHOUT EXPRESS WRITTEN CONSENT OF MILESTONE AV TECHNOLOGIES.

THIS PRINT SUPERSEDES ANY PRINT DATED PRIOR TO:

PART NO:

262065/30/2014

REVISIONS REV. DESCRIPTION CHNGD BY: DATE: APPR'D BY:

TOLERANCES: DECIMAL:

.XX = .010 .XXX = .005

FRACTIONAL: = .015

ANGULAR: = 1

1:18 DRAWN BY:

ADW DATE:

4/16/2014 APP'D BY: DATE:

X.XXXX 1/19/2011 MATERIAL NO:

MULIT FINISH:

TYPE OF FINISH sw NAME: EXPLODED VIEW FOR INSTRUCTIONS

SCALE:

DA-LITE SCREEN CO. WARSAW, INDIANA, USA

PART NO: 26206

Wall Mounting Instructions

NOTE: Use appropriate mounting hardware for the wall type and

to accommodate for the screens hanging weight (Figure 2).

Hardware is not provided.

1. Secure the wall bracket to wall studs at the desired height. Center

the wall bracket with the screen frame. You will need at least 1"

clearance above the drilled holes to hang the screen (Figure 2).

2. To install the (2) L-brackets, you must measure the overall height

of the screen frame and subtract 1" (29 mm). Using that

dimension, measure down from the top edge of the wall brackets

and mark the wall for two screw holes. The outside edge of each

L-bracket must be no greater than 5" (127 mm) away from the left

and right edges of the screen frame (Figure 2).

3. Secure the two L-brackets to the wall at the marked locations. The

longest side of the two L-brackets should be pointing upwards

when secured in order to hide the L-brackets behind the screen

frame once the screen is installed.

NOTE: The L-brackets are necessary to maintain a flat

surface for touch interactivity.

4. This step requires two people. Hang the screen on the wall

brackets. There is a lip on the back of the frame that wedges itself

into the wall brackets once fully installed. Ensure that the screen

clears the L-brackets and that the screen weight is on the wall

brackets, not the L-brackets.

Wall Bracket

L-Bracket

No More than 5" (127 mm)

Figure 2

Determining Screen Placement: When installing the IDEA Screen with BrightLink projectors, you must leave at least 22" (56 cm) of

space between the top of the screen and the ceiling to accommodate the projector wall mount.

Screws (Not Supplied)

6

DRAWING AND PART FILE MODEL NAME: LOWER_ATTACHMENT_EXPLODED(EPSON)_NO_IR

MODEL LOCATION: S:\Engineering\Solidworks Files\EPSON IDEA\INSTRUCTIONS\

SHEETS: 1 OF 1 THE INFORMATION AND DESIGNS CONTAINED IN THIS DRAWING ARE CONFIDENTIAL

AND PROPRIETARY PROPERTY OF MILESTONE AV TECHNOLOGIES NEITHER THIS DESIGN NOR ANY INFORMATION CONTAINED IN THIS DRAWING MAY BE

REPRODUCED OR DISCLOSED TO OTHERS WITHOUT EXPRESS WRITTEN CONSENT OF MILESTONE AV TECHNOLOGIES.

THIS PRINT SUPERSEDES ANY PRINT DATED PRIOR TO:

PART NO:

262065/30/2014

REVISIONS REV. DESCRIPTION CHNGD BY: DATE: APPR'D BY:

TOLERANCES: DECIMAL:

.XX = .010 .XXX = .005

FRACTIONAL: = .015

ANGULAR: = 1

1:18 DRAWN BY:

ADW DATE:

4/16/2014 APP'D BY: DATE:

X.XXXX 1/19/2011 MATERIAL NO:

MULIT FINISH:

TYPE OF FINISH sw NAME: EXPLODED VIEW FOR INSTRUCTIONS

SCALE:

DA-LITE SCREEN CO. WARSAW, INDIANA, USA

PART NO: 26206

Wall Mounting Instructions (continued)

5. Tap the bottom of the two L-brackets with the rubber mallet until

they make contact with the frame. Secure the two L-brackets to

the frame with the remaining (4) #8 x 1/2" screws (Figure 3).

6. Attach the bottom of the screen to the wall through the mounting

holes located under the marker tray.

#8 X 1/2" Screws

Figure 3

#8 X 1/2" Screws

7

Wall Mounting Instructions (continued)

7. The 16:9 IDEA Screen is designed for use with Epson BrightLink Interactive Projectors

(1480 series, 720/730 series). As such, 3" of additional space at the top of the screen

accommodate direct mounting of the BrightLink touch module (Figure 4) to the

screen, while still allowing room for a full 100" diagonal 16:9 display.

The touch module attaches directly to the IDEA Screen using the magnets on the

back of the touch module (Figure 5).

NOTE: If your BrightLink model does not include an interactive touch module,

approximately 3" of blank space at the top or bottom of the screen will be present

when projecting a 100" diagonal image.

Figure 4

DRAWING AND PART FILE MODEL NAME: LOWER_ATTACHMENT_EXPLODED(EPSON)_NO_IR

MODEL LOCATION: S:\Engineering\Solidworks Files\EPSON IDEA\INSTRUCTIONS\

SHEETS: 1 OF 1

PART NO:

26206 REVISIONS

REV. DESCRIPTION CHNGD BY: DATE: APPR'D BY:

TOLERANCES:

DECIMAL: .XX = .010

.XXX = .005

FRACTIONAL:

= .015

ANGULAR: = 1

1:18 DRAWN BY:

ADW DATE:

4/16/2014 APP'D BY: DATE:

X.XXXX 1/19/2011 MATERIAL NO:

MULIT FINISH:

TYPE OF FINISH sw NAME: EXPLODED VIEW FOR INSTRUCTIONS

SCALE:

DA-LITE SCREEN CO. WARSAW, INDIANA, USA

PART NO:

26206

Figure 5

BrightLink Touch Module

Non-projected Area

3"

100" Diagonal

COMMERCIAL BRANDS

Chief | Da-Lite | Middle Atlantic | Projecta | Vaddio

LIMITED FIVE-YEAR WARRANTY ON DA-LITE PRESENTATION PRODUCTS

Legrand AV Inc. warrants certain Da-Lite branded products to the original purchaser only, to be free from defects in materials and

workmanship for a period of five (5) years from the date of purchase by the original purchaser; provided they are properly operated

according to Da-Lite's instructions and are not damaged due to improper handling or treatment after shipment from the factory.

Limited five-year warranty applies to the following products:

Wireline Advantage, Tensioned Advantage Series, Advantage Series, Tensioned DescenderPro, DescenderPro, Tensioned Conference,

Tensioned Professional, Professional, Da-Lift Projector Lifts, Tensioned Contour, Contour, Tensioned Cosmopolitan Series,

Cosmopolitan Series, Designer Contour, Slimline, Studio, Arena, Motorized Scenic Roller, Ascender, Parallax, Parallax Thin, FullVision,

UTB Contour, Cinema Contour, Da-Snap, Perm-Wall, Imager, IDEA Screen, IDEA Panoramic, Fast-Fold Deluxe, Fast-Fold Deluxe Drapery

Kits, Flex Plex, Da-Glas, Da-Plex Rear Projection Mirror System, and Holo Screen.

This warranty does not apply to equipment showing evidence of misuse, abuse or accidental damage, or which has been tampered

with or repaired by a person other than authorized Da-Lite personnel.

Da-Lites sole obligation under this warranty shall be to repair or to replace (at Da-Lites option) the defective part of the merchandise.

Returns for service should be made to your Da-Lite dealer. If it is necessary for the dealer to return the screen or part to Da-Lite,

transportation expenses to and from Da-Lite are payable by the purchaser and Da-Lite is not responsible for damage in shipment. To

protect yourself against damage or loss in transit, insure the product and prepay all transportation expenses.

TO THE MAXIMUM EXTENT PERMITTED BY APPLICABLE LAW, THIS WARRANTY IS IN LIEU OF ALL OTHER WARRANTIES, EXPRESS

OR IMPLIED, INCLUDING WARRANTIES AS TO FITNESS FOR USE AND MERCHANTABILITY. Any implied warranties of fitness for use,

or merchantability, that may be mandated by statute or rule of law are limited to the five (5) year warranty period. This warranty gives

you specific legal rights, and you may also have other rights, which vary from state-to-state. TO THE MAXIMUM EXTENT PERMITTED

BY APPLICABLE LAW, NO LIABILITY IS ASSUMED FOR EXPENSES OR DAMAGES RESULTING FROM INTERRUPTION IN OPERATION

OF EQUIPMENT, OR FOR INCIDENTAL, DIRECT, OR CONSEQUENTIAL DAMAGES OF ANY NATURE.

In the event that there is a defect in materials or workmanship of a Da-Lite product, you may contact Customer Care at 3100 North

Detroit Street, Warsaw, IN 46582, (866) 977-3901.

IMPORTANT: THIS WARRANTY SHALL NOT BE VALID AND DA-LITE BRANDED PRODUCTS SHALL NOT BE BOUND BY THIS

WARRANTY IF THE PRODUCT IS NOT OPERATED IN ACCORDANCE WITH THE DA-LITE WRITTEN INSTRUCTIONS.

Keep your sales receipt to prove the date of purchase and your original ownership.

MARQUES COMMERCIALES

Chef | Da-Lite | Atlantique moyen | Projecta | Vaddio

GARANTIE LIMITE DE CINQ ANS SUR LES PRODUITS DE PRSENTATION DA-LITE

Legrand AV Inc. garantit certains produits de la marque Da-Lite l'acheteur original seulement, contre tout dfaut de matriaux et de

fabrication pendant une priode de cinq (5) ans compter de la date d'achat par l'acheteur original; condition qu'ils soient

correctement utiliss conformment aux instructions de Da-Lite et qu'ils ne soient pas endommags en raison d'une manipulation ou

d'un traitement incorrect aprs l'expdition de l'usine.

Une garantie limite de cinq ans s'applique aux produits suivants :

Wireline Advantage, Tensioned Advantage Series, Advantage Series, Tensioned DescenderPro, DescenderPro, Tensioned Conference,

Tensioned Professional, Professional, Da-Lift Projector Lifts, Tensioned Contour, Contour, Tensioned Cosmopolitan Series,

Cosmopolitan Series, Designer Contour, Slimline, Studio, Arena, Motorized Scenic Roller, Ascender, Parallax, Parallax Thin, FullVision,

UTB Contour, Cinema Contour, Da-Snap, Perm-Wall, Imager, IDEA Screen, IDEA Panoramic, Fast-Fold Deluxe, Fast-Fold Deluxe Drapery

Kits, Flex Plex, Da-Glas, Da-Plex Rear Projection Mirror System, and Holo Screen.

Cette garantie ne s'applique pas aux quipements prsentant des preuves de mauvaise utilisation, d'abus ou de dommages accidentels,

ou qui ont t falsifis ou rpars par une personne autre que le personnel Da-Lite autoris.

La seule obligation de Da-Lite en vertu de cette garantie sera de rparer ou de remplacer (au choix de Da-Lite) la partie dfectueuse de

la marchandise. Les retours de service doivent tre effectus auprs de votre revendeur Da-Lite. S'il est ncessaire que le revendeur

retourne l'cran ou la pice Da-Lite, les frais de transport vers et depuis Da-Lite sont la charge de l'acheteur et Da-Lite n'est pas

responsable des dommages lors de l'expdition. Pour vous protger contre les dommages ou les pertes de transport, assurez le produit

et prpayez tous les frais de transport.

DANS LA MESURE MAXIMALE PERMISE PAR LA LOI APPLICABLE, CETTE GARANTIE REMPLACE TOUTES LES AUTRES GARANTIES, EXPRESSES OU IMPLICITES, Y COMPRIS LES GARANTIES CONCERNANT L'APTITUDE L'UTILISATION ET LA QUALIT MARCHANDE. Toutes les garanties implicites d'aptitude l'emploi ou de qualit marchande qui peuvent tre imposes par la loi ou la

rgle de droit sont limites la priode de garantie de cinq (5) ans. Cette garantie vous donne des droits lgaux spcifiques, et vous

pouvez galement avoir d'autres droits, qui varient d'un tat l'autre. DANS LA MESURE MAXIMALE PERMISE PAR LA LOI APPLICABLE, AUCUNE RESPONSABILIT N'EST ASSUME POUR LES FRAIS OU DOMMAGES RSULTANT D'UNE INTERRUPTION DANS LE FONCTIONNEMENT DE L'QUIPEMENT, OU POUR DES DOMMAGES ACCESSOIRES, DIRECTS OU CONSCUTIFS DE TOUTE NATURE.

En cas de dfaut de matriau ou de fabrication d'un produit Da-Lite, vous pouvez contacter le service client au 3100 North Detroit

Street, Varsovie, IN 46582, (866) 977-3901.

IMPORTANT : CETTE GARANTIE NE SERA PAS VALABLE ET LES PRODUITS DE MARQUE DA-LITE NE SERONT PAS LIS PAR CETTE GARANTIE SI LE PRODUIT N'EST PAS UTILIS CONFORMMENT AUX INSTRUCTIONS CRITES DE DA-LITE.

Conservez votre ticket de caisse pour prouver la date d'achat et votre proprit d'origine.

7

Instructions de montage mural (suite)

7. L'cran IDEA 16:9 est conu pour tre utilis avec les projecteurs interactifs Epson

BrightLink (srie 1480, srie 720/730). Ainsi, 3 po (76,2 mm) d'espace supplmentaire

en haut de l'cran permettent un montage direct du module tactile BrightLink (figure

4) sur l'cran, tout en laissant de la place pour un affichage 16:9 de 100 po (2,45 m) en

diagonale.

Le module tactile se connecte directement l'cran IDEA l'aide des aimants

l'arrire du module tactile (Figure 5).

REMARQUE : Si votre modle BrightLink ne comprend pas de module tactile

interactif, environ 3 po (76,2 mm) d'espace vide en haut ou en bas de l'cran sera

prsent lors de la projection d'une image en diagonale de 100 po (2,54 m).

Figure 4

DRAWING AND PART FILE MODEL NAME:LOWER_ATTACHMENT_EXPLODED(EPSON)_NO_IR

MODEL LOCATION:S:\Engineering\Solidworks Files\EPSON IDEA\INSTRUCTIONS\

SHEETS: 1 OF 1

PART NO:

26206 REVISIONS

REV.DESCRIPTIONCHNGD BY:DATE:APPR'D BY:

TOLERANCES:

DECIMAL: .XX = .010

.XXX = .005

FRACTIONAL:

= .015

ANGULAR: = 1

1:18 DRAWN BY:

ADW DATE:

4/16/2014 APP'D BY:DATE:

X.XXXX1/19/2011 MATERIAL NO:

MULIT FINISH:

TYPE OF FINISHsw NAME: EXPLODED VIEW FOR INSTRUCTIONS

SCALE:

DA-LITE SCREEN CO. WARSAW, INDIANA, USA

PART NO:

26206

Figure 5

Module tactile BrightLink

Zone non projete

3 po (76,2 mm)

100 po (2,54 m) en diagonale

6

DRAWING AND PART FILE MODEL NAME:LOWER_ATTACHMENT_EXPLODED(EPSON)_NO_IR

MODEL LOCATION:S:\Engineering\Solidworks Files\EPSON IDEA\INSTRUCTIONS\

SHEETS: 1 OF 1 THE INFORMATION AND DESIGNS CONTAINED IN THIS DRAWING ARE CONFIDENTIAL

AND PROPRIETARY PROPERTY OF MILESTONE AV TECHNOLOGIES NEITHER THIS DESIGN NOR ANY INFORMATION CONTAINED IN THIS DRAWING MAY BE

REPRODUCED OR DISCLOSED TO OTHERS WITHOUT EXPRESS WRITTEN CONSENT OF MILESTONE AV TECHNOLOGIES.

THIS PRINT SUPERSEDES ANY PRINT DATED PRIOR TO:

PART NO:

26206 5/30/2014

REVISIONS REV.DESCRIPTIONCHNGD BY:DATE:APPR'D BY:

TOLERANCES: DECIMAL:

.XX = .010 .XXX = .005

FRACTIONAL: = .015

ANGULAR: = 1

1:18 DRAWN BY:

ADW DATE:

4/16/2014 APP'D BY:DATE:

X.XXXX1/19/2011 MATERIAL NO:

MULIT FINISH:

TYPE OF FINISHsw NAME: EXPLODED VIEW FOR INSTRUCTIONS

SCALE:

DA-LITE SCREEN CO. WARSAW, INDIANA, USA

PART NO: 26206

Instructions de montage mural (suite)

5. Tapoter le bas des deux supports en L avec le maillet en

caoutchouc jusqu' ce qu'ils entrent en contact avec le cadre.

Fixer les deux supports en L au chssis avec les (4) vis n 8 x 1/2 po

(12,7 mm) (Figure 3) restantes.

6. Fixer le bas de l'cran au mur travers les trous de montage

situs sous le plateau de marqueur.

Vis n 8 X 1/2 po (12,7 mm)

Figure 3

Vis n 8 X 1/2po (12,7 mm)

5 DRAWING AND PART FILE MODEL NAME:MOUNTING EXPLODED(EPSON)_NO_IR

MODEL LOCATION:S:\Engineering\Solidworks Files\EPSON IDEA\INSTRUCTIONS\

SHEETS: 1 OF 1 THE INFORMATION AND DESIGNS CONTAINED IN THIS DRAWING ARE CONFIDENTIAL

AND PROPRIETARY PROPERTY OF MILESTONE AV TECHNOLOGIES NEITHER THIS DESIGN NOR ANY INFORMATION CONTAINED IN THIS DRAWING MAY BE

REPRODUCED OR DISCLOSED TO OTHERS WITHOUT EXPRESS WRITTEN CONSENT OF MILESTONE AV TECHNOLOGIES.

THIS PRINT SUPERSEDES ANY PRINT DATED PRIOR TO:

PART NO:

26206 5/30/2014

REVISIONS REV.DESCRIPTIONCHNGD BY:DATE:APPR'D BY:

TOLERANCES: DECIMAL:

.XX = .010 .XXX = .005

FRACTIONAL: = .015

ANGULAR: = 1

1:18 DRAWN BY:

ADW DATE:

4/16/2014 APP'D BY:DATE:

X.XXXX1/19/2011 MATERIAL NO:

MULIT FINISH:

TYPE OF FINISHsw NAME: EXPLODED VIEW FOR INSTRUCTIONS

SCALE:

DA-LITE SCREEN CO. WARSAW, INDIANA, USA

PART NO: 26206

Instructions de montage mural

REMARQUE : Utiliser le matriel de montage appropri pour le

type de mur et pour tenir compte du poids de suspension de

l'cran (figure 2). Le matriel n'est pas fourni.

1. Fixer le support mural aux poteaux muraux la hauteur

souhaite. Centrer le support mural avec le cadre de l'cran. Vous

aurez besoin d'au moins 1 po d'espace au-dessus des trous percs

pour accrocher l'cran (Figure 2).

2. Pour installer les (2) supports en L, vous devez mesurer la hauteur

totale du cadre de l'cran et soustraire 1 po (29 mm). En utilisant

cette dimension, mesurer depuis le bord suprieur des supports

muraux et marquez le mur pour deux trous de vis. Le bord

extrieur de chaque support en L ne doit pas tre plus de 5 po

(127 mm) des bords gauche et droit du cadre de l'cran (Figure 2).

3. Fixer les deux supports en L au mur aux emplacements marqus.

Le ct le plus long des deux supports en L doit tre dirig vers le

haut lorsqu'ils sont fixs afin de cacher les supports en L derrire

le cadre de l'cran une fois que l'cran est install.

REMARQUE : Les supports en L sont ncessaires pour

maintenir une surface plane pour l'interactivit tactile.

4. Cette tape ncessite deux personnes. Accrocher l'cran sur les

supports muraux. Il y a une lvre l'arrire du cadre qui se coince

dans les supports muraux une fois compltement installe.

S'assurer que l'cran dgage les supports en L et que le poids de

l'cran est sur les supports muraux, pas sur les supports en L.

Support mural

Support en L

Pas plus de 5 po (127 mm)

Figure 2

Dterminer le placement de l'cran : Lors de l'installation de l'cran IDEA avec des projecteurs BrightLink, vous devez laisser au

moins 22 po (55,88 cm) d'espace entre le haut de l'cran et le plafond pour accueillir le support mural du projecteur.

Vis (non fournies)

4

DRAWING AND PART FILE MODEL NAME:TRAY_EXPLODED(EPSON)_NO_IR

MODEL LOCATION:S:\Engineering\Solidworks Files\EPSON IDEA\INSTRUCTIONS\

SHEETS: 1 OF 1 THE INFORMATION AND DESIGNS CONTAINED IN THIS DRAWING ARE CONFIDENTIAL

AND PROPRIETARY PROPERTY OF MILESTONE AV TECHNOLOGIES NEITHER THIS DESIGN NOR ANY INFORMATION CONTAINED IN THIS DRAWING MAY BE

REPRODUCED OR DISCLOSED TO OTHERS WITHOUT EXPRESS WRITTEN CONSENT OF MILESTONE AV TECHNOLOGIES.

THIS PRINT SUPERSEDES ANY PRINT DATED PRIOR TO:

PART NO:

26206 5/30/2014

REVISIONS REV.DESCRIPTIONCHNGD BY:DATE:APPR'D BY:

TOLERANCES: DECIMAL:

.XX = .010 .XXX = .005

FRACTIONAL: = .015

ANGULAR: = 1

1:18 DRAWN BY:

ADW DATE:

4/16/2014 APP'D BY:DATE:

X.XXXX1/19/2011 MATERIAL NO:

MULIT FINISH:

TYPE OF FINISHsw NAME: EXPLODED VIEW FOR INSTRUCTIONS

SCALE:

DA-LITE SCREEN CO. WARSAW, INDIANA, USA

PART NO: 26206

Instructions de montage

1. Dballer soigneusement l'appareil et placer-le sur une zone de

travail propre. La surface d'observation doit tre tourne vers le

haut.

2. Centrer le porte-marqueur au bas du cadre et fixer-le avec (3) des

vis n 8 x 1/2 po (12,7 mm) fournies. Insrer les vis travers le

plateau dans la rainure (Figure 1).

Vis n 8 X 1/2 po (12,7 mm)

Figure 1

Porte-marqueur

Avant

3

Prparation

Remarque : Deux personnes sont ncessaires pour assembler un cran IDEA. Pour maintenir une gomtrie d'image projete et un

alignement d'cran optimaux, un mur plat et droit exempt d'obstructions et de distorsions angulaires doit tre utilis.

Choisir une zone de travail propre pour l'assemblage en utilisant un matriau rembourr ou d'autres matriaux doux et propres. La zone

de travail doit tre plus grande que la taille globale de l'cran et directement en face de l'emplacement o l'cran doit tre install.

Nettoyage Nettoyage quotidien: La gomme en mousse fournie peut tre utilise pour nettoyer les marques sur la surface de l'cran faites par

l'utilisation quotidienne de marqueur effaable sec. Ne pas utiliser le nettoyant en spray Da-Lite en combinaison avec la gomme

effacer.

Nettoyage en profondeur: Pour un nettoyage complet d'cran priodique ou pour nettoyer les marques persistantes des marqueurs

effaables sec, utiliser le nettoyant en spray Da-Lite et le chiffon de nettoyage fournis. Utiliser des sections propres ou sches du

chiffon en microfibre lors de l'effacement de l'cran. Ceci est important pour viter les taches sur l'cran pendant le nettoyage. Pour

nettoyer les marqueurs permanents et autres marques involontaires sur la surface, utiliser la gomme en mousse fournie ou le nettoyant

en arosol et le chiffon de nettoyage Da-Lite.

2

Outils requis pour l'assemblage

Tournevis cruciformeNiveau Maillet en caoutchoucMtre ruban

Matriel fourni

(7) Vis n 8 x 1/2po (12,7 mm)

(1) Support mural

(2) Supports en L

Avertissement

Legrand AV Inc. et ses socits affilies et filiales (collectivement, Legrand AV ), ont l'intention de rendre ce manuel prcis et complet.

Cependant, Legrand AV ne prtend pas que les informations contenues dans ce document couvrent tous les dtails, conditions ou

variations, ni ne prvoient toutes les ventualits possibles en relation avec l'installation ou l'utilisation des produits dcrits ici. Le

contenu du prsent document est susceptible d'tre modifi sans pravis ni obligation d'aucune sorte. Dans la mesure maximale

autorise par la loi applicable, Legrand AV ne fait aucune reprsentation ou garantie, expresse ou implicite, concernant les informations

contenues dans le prsent document. De plus, Legrand AV n'assume aucune responsabilit pour l'exactitude, l'exhaustivit ou la

suffisance des informations contenues dans ce document.

Da-Lite est une marque dpose de Legrand AV. Tous les droits sont rservs.

Instructions de scurit importantes

1. Lire et comprendre toutes les instructions avant d'utiliser.

2. Le fait de ne pas fournir une rsistance structurelle adquate ce composant peut entraner des blessures graves ou endommager

l'quipement! Il est de la responsabilit de l'installateur de s'assurer que la structure laquelle ce composant est fix peut supporter

le poids de tous les quipements. Renforcer la structure au besoin avant d'installer le composant.

3. Utiliser cet cran de projection uniquement pour l'usage auquel il est destin, comme dcrit dans ces instructions. Ne pas utiliser

d'accessoires non recommands par le fabricant.

Conserver ces instructions

MANUEL D'INSTRUCTION

100 po (2,54 m) IDEA cran

pour les crans Epson BrightLink (16:9)

2020 Legrand AV Inc. 200028 3/20 Da-Lite est une marque dpose de Legrand AV Inc. Tous les autres noms de marque ou marques sont utiliss des fins d'identification et sont des marques commerciales de leurs propritaires respectifs. Tous les brevets sont protgs par des appellations existantes. Autres brevets en instance.

POUR VOTRE IMAGE | legrandav.com

tats-Unis P 866.977.3901 E av.da-lite.support@legrand.com CANADA P 877.345.4329 E av