Contents

Epson PowerLite 82c Installation Manual PDF

1 of 19
1 of 19

Summary of Content for Epson PowerLite 82c Installation Manual PDF

INSTALLATION MANUAL

ELPMBUNI

EPSON AMERICA, INC.

INDIANAPOLIS DISTRIBUTION CENTER 2350 Stafford Road Suite 101

Plainfield, IN 46168 IN-ELPMBUNI.R3

ELPMBUNI

Installation Instructions Page - 3 -

Table of Contents Warranty ............................................................................................................................................................................................... - 3 - Contact Premier Mounts ....................................................................................................................................................................... - 3 - Warning Statements .............................................................................................................................................................................. - 4 - Parts List ............................................................................................................................................................................................... - 5 - Installation Tools .................................................................................................................................................................................. - 5 - ELPMBUNI Universal Mount Assembly ............................................................................................................................................. - 6 - Projector Preparation ............................................................................................................................................................................ - 7 - Securing the Bracket to the Projector ................................................................................................................................................... - 9 - Leveling the Mounting bracket ........................................................................................................................................................... - 14 - Securing the Upper Assembly Ceiling Plate....................................................................................................................................... - 15 - Low-Profile Installation ...................................................................................................................................................................... - 16 - Securing the Projector to the Upper Assembly ................................................................................................................................... - 18 - Final Adjustments ............................................................................................................................................................................... - 19 - Installing the Plastic Caps................................................................................................................................................................... - 20 - Warranty

Limited Lifetime Warranty

All Premier Mounts products carry a limited lifetime warranty from ship date against defects in materials and workmanship. Premier Mounts is not liable for improper installation that results in damage to mounts, adapters, display equipment or personal injury. DISCLAIMER OF WARRANTY THE FOREGOING WARRANTY IS IN LIEU OF ALL OTHER WARRANTIES, EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE. Contact Premier Mounts In the event of missing and/or damage equipment, or technical questions, the following information can help in the completion of the installation. Customer Service (800) 368-9700 Technical Support techsupport@mounts.com

ELPMBUNI

Page - 4 - Installation Manual

Warning Statements WARNING: PREMIER MOUNTS DOES NOT WARRANT AGAINST DAMAGE CAUSED BY THE

USE OF ANY PREMIER MOUNTS PRODUCT FOR PURPOSES OTHER THAN THOSE FOR WHICH IT WAS DESIGNED OR DAMAGE CAUSED BY UNAUTHORIZED ATTACHMENTS OR MODIFICATIONS, AND IS NOT RESPONSIBLE FOR ANY DAMAGES, CLAIMS, DEMANDS, SUITS, ACTIONS OR CAUSES OF ACTION OF WHATEVER KIND RESULTING FROM, ARISING OUT OF OR IN ANY MANNER RELATING TO ANY SUCH USE, ATTACHMENTS OR MODIFICATIONS.

WARNING: THE CEILING STRUCTURE MUST BE CAPABLE OF SUPPORTING A MAX

WEIGHT OF 25 LBS., THE WEIGHT OF THE PROJECTOR. IF NOT, THE CEILING MUST BE REINFORCED. PROPER INSTALLATION PROCEDURE BY QUALIFIED PERSONNEL AS OUTLINED IN THE INSTALLATIONS INSTRUCTIONS MUST BE ADHERED TO. FAILURE TO DO SO COULD RESULT IN SERIOUS PERSONAL INJURY.

WARNING: SAFETY MEASURES MUST BE PRACTICED AT ALL TIMES DURING THE

INSTALLATION OF THIS PRODUCT. USE PROPER SAFETY GEAR AND TOOLS FOR THE INSTALLATION PROCEDURE TO PREVENT PERSONAL INJURY.

WARNING: PRIOR TO THE INSTALLATION OF THIS PRODUCT, THE INSTALLATION

INSTRUCTIONS SHOULD BE READ AND COMPLETELY UNDERSTOOD. THE INSTALLATION INSTRUCTIONS MUST BE READ TO PREVENT PERSONAL INJURY AND PROPERTY DAMAGE. KEEP THESE INSTALLATION INSTRUCTIONS IN AN EASILY ACCESSIBLE LOCATION FOR FUTURE REFERENCE.

Indicates that the power plug is to be disconnected from the power outlet.

Contact Premier Mounts with any questions (800) 368-9700.

Safety precautions must be taken at all times.

Warning and Caution statements.

A secure structure must support the weight, or load, of the projector. When mounting to a ceiling that contains wooden studs, dead center of the wooden stud must be confirmed prior to installation.

Do not install on a structure that is prone to vibration, movement or chance of impact. Failure to do so could result in damage to the projector and/or damage to the mounting surface.

Do not install near heater, fireplace, direct sunlight, air conditioning or any other source of direct heat energy. Failure to do so may result in damage to the projector and could increase the risk of fire.

At least two qualified people should perform the installation procedure. Injury and/or damage can result from dropping or mishandling the projector.

Recommended mounting surfaces: wooden studs, solid-flat concrete, and reinforced metal studs. If the mount is to be installed on any surface other than wooden studs, use suitable hardware (which is commercially available).

ELPMBUNI

Installation Manual Page - 5 -

Parts List NOTE: This mount is shipped with all proper installation hardware and components. Make sure that none of

these parts are missing and/or damaged before beginning installation. If there are parts missing and/or damaged, please stop the installation and contact Premier Mounts (800-368-9700).

Upper Assembly (Qty 1)

Mounting Bracket (Qty 1)

Plastic Barrel Caps (Qty 4)

M3 Flat Washers (Qty 4)

Note: Must be used with the M3 x 16 Phillips screws.

Lag Screws (#14 x 2)

(Qty 3)

M4 x 12 Security

Head Screws (Qty 4)

M3 x 16mm Phillips Head

Screws (Qty 4)

NOTE: The following hardware is included in the hardware pack but is not required for the installation. M5 x 12mm Security Head Screws (Qty 4) M6 x 12mm Security Head Screws (Qty 4)

Installation Tools Phillips Head Screw Driver Portable Drill Soft Material/ Blanket Pencil Allen Wrench (Supplied) Level (Supplied) Tape Measure Stud Finder (Commercially Available) Ladder M5 Allen Wrench NOTE: Mounting screws will vary by projector. Please see the following pages for model specific hardware:

Pages 10, 11, 12, and 13.

ELPMBUNI

Page - 6 - Installation Manual

ELPMBUNI Universal Mount Assembly A Single Wooden Stud

Mounting Points B Solid Structure Mounting

Points C Ceiling Plate D Allen Wrench E Height Adjustment Screws F Tension Knobs G Safety Knob H Security Screws I Leveling Barrels J Universal Mounting Bracket K Leg Assembly L Projector (Not Supplied) M Tri-Lock Opening

Option 1

Option 2

Combination Leg

Single Leg

NOTE: See the best configuration for your projector for filter and lamp access.

NOTE: The four (2-piece) leg assemblies can be used as single leg or any combination of single and dual legs together as shown in Options 1 and 2. The number of legs may vary depending on the number of mounting points found on the bottom of your projector.

F

E

L

H

K

B

G D

A

J

C

I

M

D

J

M

L

ELPMBUNI

Installation Manual Page - 7 -

Projector Preparation WARNING: Proper installation procedure by qualified personnel as outlined in the installation instructions

must be adhered to. Failure to do so could result in serious personal injury and possible damage to the projector.

CAUTION: THE PROJECTOR IS FRAGILE; HANDLE WITH CARE AT ALL TIMES. NOTE: Review the projectors manufactures operation manual and refer to the ceiling installation

instruction. Here you will normally find important reference information regarding installation dimensions such as (distance from the screen to the lens of the projector, top of the lens placement to the top screen etc. Adherence to these recommendations during your installation will enhance the quality of your final image on the screen.

1. Carefully invert the projector and place it on a smooth flat surface. 2. Identify the number of mounting points and screw thread (pitch) size. 3. Most projectors have either three or four mounting points and are M4 in thread size (Figure 1).

Figure 1

Inverted Projector

Flat surface

Mounting Points

Blanket, soft cloth etc

ELPMBUNI

Page - 8 - Installation Manual

4. Separate the upper assembly from the projector mounting bracket by slightly loosening the two tension knurl knobs to create free play between the bracket tri-lock assembly and the upper section tri-lock assembly points.

5. Next loosen the safety screw knurl knob far enough to allow the two parts to be rotated 180 apart and separate.

Figure 2 Figure 3

Figure 4

Tension Knobs

Upper Assembly

Safety Knob

Tri-Lock Opening

Rotate 180 To Unlock

ELPMBUNI

Installation Manual Page - 9 -

Securing the Bracket to the Projector NOTE: The two-piece mounting legs are designed to allow routing of the legs around critical ventilation

screens on the base of the projector as shown. You may also reduce the two-piece leg to a one-piece leg as shown for a better overall fit to the projector.

1. Locate the mounting points on the bottom of the projector and use the appropriate number of mounting

legs. 2. Select the mounting hardware that your projector requires and loosely install the universal mount to your

projector. NOTE: If your projector requires M3 mounting hardware. Use the M3 x 16 Phillips screws with the M3

flat washers (supplied). Insert the M3 x 16 Phillips screws with the flat washers attached through the leveling barrel. Using a Phillips screwdriver, loosely secure the screws to the projector (Figure A).

NOTE: The levelers and leg assembly screws must be loose in order to adjust the height of the mounting

bracket.

Figure 5

FIGURE A

FIGURE 7 One-Piece Leg

FIGURE 6

Two-Piece Leg

Leveling Barrels

Mounting Hardware

Allen Wrench

Inverted Projector

Line up the leveling barrels to the mounting points.

ELPMBUNI

Page - 10 - Installation Manual

NOTE: If your projector model is not shown, when arranging the leg combination, simply ensure access to filters and lamp housings when aligning brackets. This mount works with all sub-25 pound projectors.

PowerLite S3, S4, 62C, 76C, 82C, Hardware: M4 x 12mm (Qty 3)

PowerLite 830p, 835p

Hardware: M4 x 12mm (Qty 4)

ELPMBUNI

Installation Manual Page - 11 -

PowerLite 732c, 737c, 740C, 745C, 750c, 755c, 760c, 765c

Hardware: M4 x 12mm (Qty 3)

Top View

Front View

ELPMBUNI

Page - 12 - Installation Manual

PowerLite 7800p, 7850p, 7900p Hardware: M4 x 12mm (Qty 4)

PowerLite 61p, 81p, 821p

Hardware: M4 x 12mm (Qty 4)

ELPMBUNI

Installation Manual Page - 13 -

PowerLite S1, S1+

Hardware: M4 x 12mm (Qty 3)

PowerLite 6100i

Hardware: M4 x 12mm (Qty 4)

ELPMBUNI

Page - 14 - Installation Manual

Leveling the Mounting bracket 1. Rotate the leveling barrels to level the mounting bracket next, position the mounting bracket so that it

avoids most, if not all, ventilation points (including lamp & filter access doors). 2. When the position desired is achieved tighten the mounting hardware to the projector then tighten the hex

head leg screws with the Allen wrench (supplied) (Figure 8 and Figure 9).

CAUTION: Secure but do not over-tighten the mounting hardware. Failure to do so will result in damaging the threads in the projector.

UP

DOWN

Figure 8

Level

Allen Wrench

Leveling Barrels

Inverted Projector

Adjusting the Mount

ELPMBUNI

Installation Manual Page - 15 -

Securing the Upper Assembly Ceiling Plate 1. Review your projectors distance calculation to determine what distance is recommended from the front of

the lens to the edge of the screen for best picture ratio. 2. Locate the inverted projectors top of the lens point to a point centered horizontally on the screen and no

higher then the top image edge of the screen). 3. It is normally better to have the top edge of the lens as close to parallel with the top image edge of the

screen as well. 4. Before you mount your screen and projector, make sure the mounting location will safely support the

weight of the projector. NOTE: Make sure to measure from the center of the mounting bracket to the front edge of the lens to

determine the proper placement of the center of the upper assembly.

NOTE: If installing the security kit (ELPMBSEC), please refer to the security kit installation guide before attaching the ceiling plate to the ceiling or wall.

5. Secure the ceiling assembly into a solid wood ceiling stud with the three (3) #14 x 2 wood screws

(supplied) or with other (commercially available) hardware depending on your installation environment (Figure 9).

Figure 9

Secure the ceiling mount to the center of the wood stud.

Ceiling Structure

Wood Screws

Upper Assembly

Knurl Knobs (3ea)

Ceiling Wood Stud

ELPMBUNI

Page - 16 - Installation Manual

Low-Profile Installation 1. If your installation requires the overall height of the mount to be less that the approximate 9 shown with

the standard mount assembly, you can convert the height to only 2 by simply removing the adjustment channel as shown.

2. Once the extension channel is removed, attach the upper ceiling plate to the ceiling. 3. Once attached install the bell housing assembly to the upper ceiling plate as shown (Figure 10, Figure 11,

and Figure 12).

Figure 10

Ceiling Plate

Remove the M8 x 16mm Screws, flat Washers and Star Washers

Allen Wrench

Remove the Middle Extension Completely

Remove the M8 x 16mm Screws, Flat Washers, and Star Washers (Both Sides)

Remove the M8 x 16mm Screws, Flat Washers, and Star Washers (Both Sides)

Bell Housing

ELPMBUNI

Installation Manual Page - 17 -

Figure 11

Figure 12

NOTE: Do not use the star washers on a close ceiling application.

Wood Stud

Ceiling Structure

Ceiling Plate

Wood Screws

Wood StudCeiling Structure

Secure the Bell Housing with Two M8 x 16mm Screws and Flat Washers Only

Attach Bell Housing to the Ceiling Plate

Allen Wrench

ELPMBUNI

Page - 18 - Installation Manual

Securing the Projector to the Upper Assembly 1. Make sure the three-knurl knobs are loosened to fully expose to the tri-lock mounting plate in the base

of the upper assembly. 2. Carefully lift the projector and insert the mounting bracket mating special tri-lock cutout into the mating

portion of the upper assembly. 3. Once inserted rotate the projector and mounting bracket 180 and secure the rear safety knob first to

prevent further rotation of the bracket in the upper assembly. 4. Tighten the remaining two tension knurl knobs until the mount becomes rigid. 5. The safety knob should line up with the alignment slot on the mounting bracket (Figure 13).

NOTE: Follow the number sequence prior to securing the projector to the upper assembly.

Figure 13

The alignment slot must be in direct alignment with the safety knob to lock the mounting bracket to the upper assembly

Universal Mount

Alignment Slot

Tri-Lock Opening

Projector Mount

Tension Knurl Knobs

Safety Knurl Knob

Insert universal bracket to the tri-lock, then rotate the projector 180

ELPMBUNI

Installation Manual Page - 19 -

Final Adjustments 1. With the projector secured in the mount and power on and signal supplied to the projector you can now

proceed with the final height, tilt, and roll and yaw to optimize the projected image. 2. The height can be adjusted by slightly loosening the two 8mm height adjustment screws and raising or

lowering the projector (Figure 14). 3. Once the height is achieved tighten the two screws. 4. To adjust the tilt angle of the projector, slightly loosen the side M8 screws and tilt to the desired angle to

the screen and firmly tighten the two M8 tilt adjustment screws (Figure 15). 5. If roll adjustment is needed to square the images on the screen, slightly loosen the front and rear M8

screws and adjust to the desired angle then firmly tighten the two M8 roll adjustment screws (Figure 16).

Figure 14

Figure 15

Figure 16

Wood Stud

Ceiling

(Roll) Adjusting Screws

Allen Wrench

Allen Wrench

Wood Stud

Ceiling

Tilt Adjusting Screws

Wood Stud

Allen Wrench Height Adjustable Screws

Ceiling

ELPMBUNI

Page - 20 - Installation Manual

Installing the Plastic Caps 1. Once all the final adjustments have been done, install

Manualsnet FAQs

If you want to find out how the PowerLite 82c Epson works, you can view and download the Epson PowerLite 82c Installation Manual on the Manualsnet website.

Yes, we have the Installation Manual for Epson PowerLite 82c as well as other Epson manuals. All you need to do is to use our search bar and find the user manual that you are looking for.

The Installation Manual should include all the details that are needed to use a Epson PowerLite 82c. Full manuals and user guide PDFs can be downloaded from Manualsnet.com.

The best way to navigate the Epson PowerLite 82c Installation Manual is by checking the Table of Contents at the top of the page where available. This allows you to navigate a manual by jumping to the section you are looking for.

This Epson PowerLite 82c Installation Manual consists of sections like Table of Contents, to name a few. For easier navigation, use the Table of Contents in the upper left corner.

You can download Epson PowerLite 82c Installation Manual free of charge simply by clicking the “download” button in the upper right corner of any manuals page. This feature allows you to download any manual in a couple of seconds and is generally in PDF format. You can also save a manual for later by adding it to your saved documents in the user profile.

To be able to print Epson PowerLite 82c Installation Manual, simply download the document to your computer. Once downloaded, open the PDF file and print the Epson PowerLite 82c Installation Manual as you would any other document. This can usually be achieved by clicking on “File” and then “Print” from the menu bar.