Epson Action Printer 2250 User's Guide PDF

U S E R S G U I D E

4001245 GO1-01

Printer Parts

printer cover

parallel in&ace u

ribbon Cartridge

FONT lights

rL

Never move this lever.

,~~ -~~~

Font button LF/FF button

Control panel

-

EPSON,+eqpm 2250

All rights reserved. No part of this publication may be reproduced, stored in a retrieval system, or transmitted in any form or by any means, mechanical, photocopying, recording, or otherwise, without the prior written permission of Seiko Epson Corporation. No patent liability is assumed with respect to the use of the information contained herein. While every precaution has been taken in the preparation of this book, Seiko Epson Corporation assumes no responsibility for errors or omissions. Neither is any liability assumed for damages resulting from the use of the information contained herein.

Neither Seiko Epson Corporation nor its affiliates shall be liable to the purchaser of this product or third parties for damages, losses, costs, or expenses incurred by purchaser or third parties as a result of: accident, misuse, or abuse of this product or unauthorized modifications, repairs, or alterations to this product, or (excluding the U.S.) failure to strictly comply with Seiko Epson Corporations operating and maintenance instructions.

Seiko Epson Corporation shall not be liable against any damages or problems arising from the use of any options or any consumable products other than those designated as Original Epson Products or Epson Approved Products by Seiko Epson Corporation.

Epson and Epson ESC/P are registered trademarks of Seiko Epson Corporation.

Action Printer is a trademark of Epson America, Inc.

Copyright 1992 by Seiko Epson Corporation Nagano, Japan

Users Guide

FCC Compliance Statement

For United States Users

This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio or television reception. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause interference to radio and television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures.

. Reorient or relocate the receiving antenna.

. Increase the separation between the equipment and receiver.

. Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.

. Consult the dealer or an experienced radio/TV technician for help.

WARNING The connection of a non-shielded equipment interface cable to this equipment will invalidate the FCC Certification of this device and may cause interference levels which exceed the limits established by the FCC for this equipment. It is the responsibility of the user to obtain and use a shielded equipment interface cable with this device. If this equipment has more than one interface connector, do not leave cables connected to unused interfaces.

Changes or modifications not expressly approved by the manufacturer could void the users authority to operate the equipment.

For Canadian Users

This digital apparatus does not exceed the Class B limits for radio noise emissions from digital apparatus as set out in the radio interference regulations of the Canadian Department of Communications.

Le present appareil numerique nemet pas de bruits radioelectriques d&passant les limites applicables aux appareils numeriques de Classe B prescrites dans le reglement sur le brouillage radioelectrique edict6 par le Ministere des Communications du Canada.

ii

Important Safety Instructions .

.

.

.

.

.

.

.

.

.

.

.

.

Read all of these instructions before you set up your printer.

Follow all warnings and instructions marked on the printer.

Unplug the printer from the wall outlet before you clean it, and use a damp cloth for cleaning, not liquid or aerosol cleaners.

Do not use your printer near water or spill any liquid on it.

Do not place the printer on an unstable cart, stand, table or other surface that may allow the printer to fall.

Do not block any slots or openings in the cabinet. These are provided for the ventilation necessary to ensure reliable operation and protection from overheating. Placing the printer on a bed, sofa, rug, or other similar surface may block the openings. Also, do not place the printer in a built-in installation unless proper ventilation is provided.

Never place the printer near or over a radiator or heat register.

Use the type of power source indicated on the label. If you are not sure of the type of power available, consult your dealer or local power company.

This printer may be equipped with a plug having a third (grounding) pin, which fits only into a grounding-type outlet. This is a safety feature. If you are unable to insert the plug into the outlet, have an electrician replace your obsolete outlet. Do not defeat the purpose of the grounding-type plug.

Do not put your printer where the cord will be walked on.

If you use an extension cord, make sure that the total of the ampere ratings on the products plugged into the extension cord does not exceed the extension cords ampere rating. Also, make sure that the total of all products plugged into the wall outlet does not exceed 15 amperes.

Never push objects of any kind into your printer because they may touch dangerous voltage points or short out parts that could result in a risk of fire or electric shock.

Except as specifically explained in the users manual, do not attempt to repair the printer yourself. This could expose you to dangerous voltage points or other risks. Refer all servicing in those compartments to service personnel.

iii

. Unplug the printer from the wall outlet and have it repaired by a qualified service person under the following conditions:

When the power cord or plug is damaged or frayed

If liquid has been spilled into it

If it has been exposed to ram or water

If it does not operate normally when the operating instructions are followed. Adjust only those controls that are covered by the operating instructions since improper adjustment of other controls may result in damage and will often require extensive work by a qualified technician to restore the printer to normal operation.

If it has been dropped or the cabinet has been damaged

If it exhibits a distinct change in performance, indicating a need for service

Where United States Users Can Get Help

Epson America provides local customer support and service through a nationwide network of authorized Epson dealers and Service Centers.

Epson also provides the following support services through the Epson Consumer Resource Center at (800) 922-8911:

Assistance in locating your nearest Authorized Epson Reseller or Service Center

Technical assistance with the installation, configuration, and operation of Epson products

Sales of the ESC/P Reference manual

Epson technical information library fax service

Product literature with technical specifications on our current and new products

Sales of ribbons, supplies, parts, documentation, and accessories for your Epson product

Customer Relations

User group locations

iv

For United Kingdom Users

Epson product guarantee

Under the law, goods sold must comply with their description and must be of merchantable quality and fit for their purpose or correspond with any sample.

This guarantee does not affect the sellers legal obligation or the rights of the consumer in the consumer transactions under any Statute, including Sections 12 to 15 of the Sales of Goods Act, 1979.

All Epson Products, other than OEM products, are fully guaranteed against faulty operation or performance for a period of ONE YEAR from date of purchase by the user of the product.

All claims under this guarantee MUST be supported by evidence of purchase, normally the bill of sale invoice, and it is the responsibility of the claimant to furnish such proof. Epson (UK) Limited does not issue or operate any form of guarantee registration card.

Claims are made by the user returning the product to the supplier from whom it was purchased or, if this is impractical, to any Epson supplier who also handles the same product. In the event of any difficulty, users are requested to contact the Service Co-ordinator Manager at Epson (UK) Limited.

Epson (UK) Limited, or Epson Appointed Distributors, will at their discretion repair or replace part or all of the product to provide, in their judgement, a satisfactory performance of the product consistent with its age and apparent usage.

This guarantee covers the cost of both the parts and labour required to correct any malfunction of the equipment, but specifically excludes: wear and tear, consumables, physical damage due to incorrect use or misuse and damage or faulty operation due to unauthorized and inexpert repair.

The guarantee is restricted to the performance of the product alone, and Epson (UK) Limited does not accept responsibility for any consequential loss or damage, nor claimed or implied performance, when the product is used in any combination with other equipment or program software.

Product guarantee may be invalidated as a result of excessive or inappropriate use, use in adverse environment or in conditions outside the specifications or if the product has been subjected to unapproved modifications.

The guarantee does not cover visits to the users premises or the repair or commissioning of the product on site.

Use of options

Epson (UK) Limited shall not be liable against any damages or problems arising from the use of any options or consumable products other than those designated as Original Epson Products or Epson Approved Products by Epson (UK) Limited.

Safety information

Warning: This appliance must be earthed. Refer to rating plate for voltage and check that the appliance voltage corresponds to the supply voltage.

Important: The wires in the mains lead fitted to this appliance are colored in accordance with the following code:

Green and yellow - Earth Blue - Neutral Brown - Live

As the colors of the wires in the mains lead of this appliance may not correspond with the colored markings identifying the terminals in your plug, proceed as follows:

The green and yellow wire must be connected to the terminal in the plug which is marked with the letter E or with the earth symbol (+) or colored green or green and yellow.

The blue wire must be connected to the terminal in the plug marked with the letter N or colored black.

The brown wire must be connected to the terminal in the plug marked with the letter L or colored red.

If damage occurs to the plug, replace the cord set or consult a qualified electrician.

Replace fuses only with a fuse of the correct size and rating.

vi

Contents

Introduction 1

Features ........................................................................................... 1 Finding Your Way Around .......................................................... 2 Warnings, Cautions, and Notes .................................................. 2

Chapter 1 Setting Up the Printer 1-1

Unpacking the Printer ............................................................... 1-2 Choosing a Place for the Printer .............................................. 1-4 Installing the Ribbon Cartridge ............................................... 1-5 Plugging in the Printer .............................................................. 1-7 Running the Self Test ................................................................. 1-8 Connecting the Printer to Your Computer ............................. 1-11 Setting Up Your Software Programs ....................................... 1-13

Chapter 2 Paper Handling 2-1

Printing on Single Sheets . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-2 Using Continuous Paper with the Push Tractor . . . . . . . . . . . . 2-5 Switching Between Continuous Paper and Single Sheets ....2-13 Printing on Special Paper . . . . . . . . . . . . . . . . . . . . . . . . . .. . . . . . . . . . . . . . . 2-15

Chapter 3 Using the Printer 3-2

Operating the Control Panel ..................................................... 3-2 Selecting Character Fonts.. ....................................................... . 3-5 Using the Default-Setting Mode .............................................. 3-5 Maintenance and Transportation ............................................ 3-16 Troubleshooting ......................................................................... 3-19

Contents vii

Appendix A-1

Technical Specifications ........................................................... A-2 Command Summary ................................................................ A-13 Character Tables ........................................................................ A-21

Glossary GL-1

Index IN-1

Vii i Contents

Introduction

Your new Epson printer is an advanced 9-pin dot matrix printer that combines high performance with a wide range of features.

Features

These features give your Epson printer outstanding value:

Fast printing speed. You can print up to 240 characters per second in 12 cpi draft mode.

Easy paper handling. The built-in paper cassette holds up to 50 single sheets of paper. You can also install the push tractor to print on continuous paper, multi-part forms, and labels. Also you can switch between single-sheet and continuous printing without removing either paper supply.

Compatibility. The printer supports the Epson ESC/P

commands widely used in software programs written for other Epson LX printers.

Two printer positions. You can set the printer upright or flat, whichever you prefer.

A range of popular fonts. You can choose from two draft fonts and two near letter quality fonts for professional results.

Unique control-panel design. The sleek, two-button panel makes it easy to customize the printers default settings.

No adjustment necessary for paper thickness. You do not need to adjust a paper thickness lever when you use thick paper.

In some locations, the push tractor is an option (part number C80026*) .

Introduction 1

Introduction

Finding Your Way Around

Heres what youll find in this book:

l Chapter 1 contains step-by-step instructions for unpacking, setting up, testing, and connecting your printer. Be sure to read and follow these instructions.

l Chapter 2 is a detailed discussion of paper handling.

l Chapter 3 describes how to use the control panel to customize your printer settings. It also contains maintenance and troubleshooting information.

l The Appendix includes the printer specifications, commands, and character tables.

l A glossary of printer terms and an index are at the end.

Warnings, Cautions, and Notes

I!!!9 WARNINGS must be followed carefully to avoid bodily injury.

CAUTIONS must be observed to avoid damage to your equipment.

Notes contain important information and useful tips on the operation of your printer.

2 Introduction

Chapter 1

Setting Up the Printer

Unpacking the Printer.. ............................................................. 1-2 Removing the protective materials .................................... 1-3

Choosing a Place for the Printer . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-4

Installing the Ribbon Cartridge . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-5

Plugging in the Printer . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-7

Running the Self Test ................................................................ 1-8 Loading paper into the paper cassette.. ............................. 1-8 Running the test .................................................................... 1-11

Connecting the Printer to Your Computer . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-11

Setting Up Your Software Programs.. ..................................... 1-13 Printing a test file .................................................................. 1-14

Setting Up the Printer 1-1

Unpacking the Printer Your printer box should include these items.

printer output guide ribbon cartridge

@i

power cord* cable clip push tractor**

l In some locations, the power cord is attached to the printer. ** In some countries, the push tractor is an option (part number CSOOZS*).

0t CAUTION: There are several versions of this printer l designed for different voltages, and it is not possible to

change the voltage. If the label on the back of the printer does not show the correct voltage for your country, contact your dealer.

1-2 Setting Up the Printer

Unpacking the Printer

Removing the protective materials

During shipping, a piece of foam packing, a print head protector, and a piece of tape protect the printer and paper cassette. Before you use the printer, you must remove these protective items.

1. Use the tabs on both sides of the printer cover to lift it off the printer. First remove the protective cover. Then remove the foam packing and the two protectors from inside the printer.

2.

3.

Remove the ribbon cartridge from its foam packing.

Pull the paper cassette out of the printer. Remove the tape that holds down the metal plate in the cassette during shipping.

Note: Store these protective items with the other packing materials.

Setting Up the Printer 1-3

Choosing a Place for the Printer The printer works flat or upright, as shown below. You can set it whichever way fits your preference or working space. (When you install the push tractor, you must use the flat position.)

When selecting a place for your printer, follow these guidelines:

Place the printer on a flat, stable surface. Do not slide the printer on rough surfaces because you may damage the flap on the bottom.

Place the printer close enough to the computer for its interface cable to reach the computer.

Leave adequate room for easy operation and maintenance.

Avoid locations that are subject to direct sunlight, excessive heat, moisture, or dust.

Use a grounded outlet; do not use an adapter plug.

Place the printer where you can easily unplug the power cord.

Avoid electrical outlets controlled by wall switches or automatic timers, and avoid outlets on the same circuit as large motors or other appliances that can cause fluctuations in line voltage.

Keep the entire computer system away from potential sources of electromagnetic interference, such as loudspeakers or the base units of cordless telephones.

1-4 Setting Up the Printer

Choosing a Place for the Printer

If you plan to use a printer stand, follow these guidelines:

Use a stand that supports at least 10 kg (22 lbs).

Never use a stand that tilts the printer. It should always be kept level.

Make sure to provide enough clearance below the stand so your continuous paper feeds smoothly.

Place cables so they do not interfere with paper feeding; secure them to a leg of the stand if possible.

Align the continuous paper stack so the paper feeds straight into the tractors sprocket units.

Installing the Ribbon Cartridge Before you install the ribbon cartridge, make sure the power cord is not plugged into an electrical outlet.

1. Use the tabs on both sides of the printer cover to lift it off the printer. Then slide the print head to the middle of the printer.

Setting Up the Printer 1-5

Installing the Ribbon Cartridge

2. Turn the ribbon-tightening knob in the direction of the arrow to remove any slack in the ribbon. Insert the ribbon cartridge into the printer as shown; then press both sides of the cartridge firmly to fit the plastic posts into the slots.

3. Turn the ribbon-tightening knob to feed the ribbon into place. Make sure it is not twisted or creased.

0? CAUTION: l

l Never move the small levers on the ends of the metal shaft (shown below). They have already been adjusted at the factory.

Never move this lever.

l Disregard the numbers 0 and 1 under the printer cover on the left side. They are not necessary for printer operation.

1-6 Setting Up the Printer

Installing the Ribbon Cartridge

4. Replace the printer cover by inserting its tabs into the holes on the printer as shown below; then close the cover.

Plugging in the Printer 1. Make sure the power switch on the printer is turned off. It is off

when the 0 side of the switch is pressed down.

2. Check the label on the back of the printer to make sure the voltage required by the printer matches that of your electrical outlet.

01 CAUTION: If the rated voltage and your outlet voltage do l not match, contact your dealer for assistance. Do not plug

in the power cord.

Setting Up the Printer 1-7

Running the SelfTest

3. If the power cord is not attached to the printer, connect it to the AC inlet on the printer.

4. Plug the power cord into a properly grounded electrical outlet.

Running the Self Test You can run the self test with either continuous paper or single sheets; this section describes the easier way, with single sheets.

If you want to use continuous paper, see Using Continuous Paper with the Push Tractor in Chapter 2.

Loading paper into the paper cassette

1. You can install the output guide to support printed pages as they come out of the printer. To install it, insert the tabs on the guide into the mounting slots on the printer case as shown below. Be sure to turn the guide over and install it in the opposite direction when you use the printer in the upright position.

1-8 Setting Up the Printer

Running the Self Test

2. Pull the paper cassette out of the printer.

3. Fan a stack of A4 or letter-size paper and then even up the edges.

Note: The US version uses letter-size paper; all others use A4 paper. The paper size (letter or A4) is shown on the inside of the paper cassette. The cassette holds up to 50 sheets (70 kg or 22 lb maximum).

4. Pull out the paper support.

Setting Up the Printer 1-9

Running the Self Test

5. While holding down the metal plate in the paper cassette, put the paper in the cassette. Make sure the paper is underneath all five tabs, especially the small ones on the top edge of the cassette.

tabs

tabs

6. Insert the paper cassette into the printer as far as it will go. The edge of the paper stack extends beyond the front of the printer.

1-10 Setting Up the Printer

Running the Self Test

Running the test

1. Make sure the printer is turned off.

2. While holding down the LF/FF (w ) button, turn on the printer. The printer gives two long and two short beeps, and then it loads the paper automatically and begins the self test.

The printer prints characters in the current font and character table. Here is part of a typical self test: !#$%Sr*( I*+,- ./0123456789:;<=>?8ABCDEFGHIJKL

!#$%&-( )*+,- ./0123456789:;<=>?@ABCDEFGHIJKLM #$%&O*+,-./012345678Q:;<=>?@ABCDEFGHIJKLMN #$%&( )a+,- ./0123456789:;<=>?@ABCDEFGHIJKLMNO $%&()*+,-./012345678S:;<=>?@ABCDEFGHIJKLMNOP %&( )*+,- ./0123456789:;<=>?@ABCDEFGHIJKLMNOPQ &-()a+,- ./0123456789:;<=>?@ABCDEFGHIJKLMNOPQR

Note: If the paper cassette is empty when you turn the power on, the printer beeps three times and the READY light flashes. Load paper as described above and press the LF/FF button to start the self test.

3. To stop the self test, turn off the printer.

If the self test does not work properly, contact your dealer.

Connecting the Printer to Your Computer If the self test prints correctly, youre ready to connect your printer to the computer. You need a parallel printer cable to connect your computer to the printers built-in parallel interface.

Follow these steps to connect the parallel interface cable:

1. Make sure both the printer and computer are turned off; then plug the cable connector securely into the printers interface connector.

Setting Up the Printer 1-11

Connecting the Printer to Your Computer

2. Squeeze the wire clips together until they lock in place on either side.

Note: If your cable has a ground wire, connect it to the ground connector below the interface connector.

3. Put the cable through the cable clip; then insert the clip in the slot on the bottom of the printer. (You may have to remove the output guide when you put the printer upright to attach the cable clip.)

I

1-12 Setting Up the Printer

Connecting the Printer to Your Computer

4. Plug the other end of the cable into the computer. If there is a ground wire at the computer end of the cable, attach it to the ground connector at the back of the computer.

Note: If you want the power cord or interface cable to be on the opposite side, route it through the slot on the back.

Setting Up Your Software Programs Most software programs let you specify the type of printer you use so that the program can take full advantage of the printers features. Many programs provide a printer selection menu.

Setting Up the Printer 1-13

Sett ing Up Your Software Programs

Because the family of Epson printers shares a great many commands, you can use a software program even if does not list your printer on its printer selection menu. Choose from the following list (the printers are listed in the order of preference).

LX-100 ActionPrinter 2250 LX-810/850 LX-800 LX-86 LX-80 FX-850 FX-86e / 800 EX-800 FX-85 FX-80+ FX-80

If none of these printers is listed, select the first one of these available: LX, FX, EX, RX, MX, Epson printer, Standard printer, Draft printer.

To use all of the features of the printer, however, it is best to choose a program with one of the LX printers on its menu. If your program does not list one of these printers, contact the software manufacturer to see if an update is available.

Printing a test file

After you select the most appropriate printer, create and print a test file using the fonts, symbols, features, and formats that you use most often. Printing the test file shows you how the printer works with your software program.

If the printing results are not what you expect, see Troubleshooting in Chapter 3, or consult your computer or software manual.

1-14 Setting Up the Printer

Chapter 2 Paper Handling

Printing on Single Sheets ......................................................... 2-2 Tips for using the paper cassette ....................................... 2-2 Loading paper manually ..................................................... 2-3

Using Continuous Paper with the Push Tractor .................. 2-5 Installing the push tractor.. ................................................. 2-5 Loading continuous paper.. ................................................ 2-7 Tips for using continuous paper ........................................ 2-10 Using the tear-off feature .................................................... 2-11 Removing the push tractor ................................................. 2-11

Switching Between Continuous Paper and Single Sheets . . . . . . . . . . . 2-13 Switching to single sheets . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-13 Switching to continuous paper . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-14

Printing on Special Paper.. ....................................................... 2-15 Envelopes .............................................................................. 2-16 Multi-part forms ................................................................... 2-17 Labels ..................................................................................... 2-17

Paper Handling 2-1

Printing on Single Sheets You can load standard-sized single sheets with the paper cassette and you can load single sheets of paper from 148 mm (5.8 inches) to 257 mm (10.1 inches) wide with the manual insertion slot.

Tips for using the paper cassette

Review Loading paper into the paper cassette on page 1-8. Also, the tips below will help you get the best performance when using the cassette.

Load paper in the cassette before you turn on the printer and send data. When the printer receives data from the computer, it loads a single sheet automatically and begins to print.

If the printer runs out of paper during a print job, reload the paper cassette and press the LF/FF button to load the paper.

Press the LF/FF button to eject a sheet of loaded paper.

You can adjust the top-of-form position with the gear under the printer cover. It is marked by + and - signs. Open the printer cover and turn the gear to adjust the position. The notches on the ribbon mask indicate the base line of printed characters. The gear adjustment affects only the loaded page. If you want to change the top-of-form position permanently, you can adjust it in the default-setting mode described in Chapter 3. However, most software programs take care of the top and bottom margins. You usually dont need to set the top-of-form position on the printer.

ribbon mask

- c base line of characters

2-2 Paper Handling

Printing on Single Sheets

l When you want to push the paper support back into the paper cassette, first remove paper from the cassette. Then hold down the locking tab while pushing the paper support in.

l The default page length for the paper cassette is 65 lines (A4-size paper) or 61 lines (letter-size paper). You can change it using your software or printer commands, if necessary. See the Appendix for more about printer commands.

l You can switch to manual insertion or to the push tractor without removing the paper cassette. For instructions, see Loading paper manually or Switching Between Continuous Paper and Single Sheets later in this chapter.

Loading paper manually

You can load single sheets of paper from the rear manual insertion slot. (If youve installed the push tractor, remove it before loading paper manually.)

1. Place the printer in the upright position and turn it on.

Paper Handling 2-3

Printing on Single Sheets

2. Next, lower the flap on the rear slot. Then insert a single sheet into the slot, aligning the paper edge with the arrow mark on the printer case. The page loads automatically. When the printer receives data, it begins printing.

Be sure to raise the flap when not using manual insertion.

l You can adjust the top-of-form position in the same way that you do for paper loaded from the cassette.

l When you want to switch to the paper cassette, press the LF/FF button without inserting a page into the rear slot. The printer loads a page from the cassette.

2-4 Paper Handling

Using Continuous Paper with the Push Tractor You can use the push tractor to print on continuous paper from 101 mm (4 inches) to 254 mm (10 inches) wide.

Note: In some locations, the tractor is an option (part number C80026*).

Installing the push tractor

1. Make sure the printer is turned off and is in the flat position. Remove the paper guide.

2. Make sure the paper-release lever on the left side of the push tractor is lowered to the single-sheet position.

Paper Handling 2-5

Using Continuous Paper with the Push Tractor

3. Hold the tractor as shown and fit the edges of both sides into the slots at the back of the printer. Then lift it straight up until you hear the unit snap into place.

4. Raise the paper-release lever and push it firmly into the continuous-paper position.

2-6 Paper Handling

Using Continuous Paper with the Push Tractor

Loading continuous paper

1. Place the continuous paper supply below the printer so the paper feeds smoothly into the printer as shown. (You can also use a printer stand. )

CAUTION: When you are using labels with the tractor, always put the supply below the printer and have the printed labels feed out the back of the printer. Otherwise they may come off their backing and cause a jam.

2. Make sure the paper-release lever is in the upper position.

3. Release the sprocket units by pushing the lock levers up.

Paper Handling 2-7

Using Continuous Paper with the Push Tractor

4. Adjust the right sprocket unit, aligning the paper edge with arrow mark on the case. Then slide the left sprocket unit to match the width of your paper, but do not lock it.

5.

the

Position the paper support midway between the two sprocket units. Open both sprocket covers.

2-8 Paper Handling

Using Continuous Paper with the Push Tractor

6. Make sure your paper has a clean, straight leading edge. Fit the first four holes of the paper over the sprocket pins, and then close the sprocket covers. Slide the left sprocket unit to remove any slack in the paper. Then push the lock lever down to lock it in place. Note that this printer prints on the underside of the paper.

7. Turn on the printer. It advances the paper to the loading position automatically when it receives data.

Note: If the printer runs out of paper during a print job, load additional paper onto the push tractor and press the LF/FF button.

Paper Handling 2-9

Using Continuous Paper with the Push Tractor

Tips for using continuous paper

l You can adjust the top-of-form position temporarily. Open the printer cover and turn the gear marked by + and - signs to adjust the position. This adjustment is lost when you turn off the printer or feed the paper backward to the paper-park position described later in this chapter.

paper-park position

l If you want to change the top-of-form position permanently, adjust it with the default-setting mode as described in Chapter 3.

l Each time you turn on the printer with paper loaded, it reverses the continuous paper to the paper-park position and then advances it to the next top-of-form. Always remove your printed sheets before you turn off the printer to keep the top-of-form position accurate.

Note: When you set the back-feed setting to Disable in the default-setting mode, the printer does not feed the paper backward even if you press the LF/FF and FONT buttons or you turn on the printer with paper loaded. For details, see Labels in this chapter or Using the Default-Setting Mode in Chapter 3.

2-10 Paper Handling

Using Continuous Paper with the Push Tractor

Using the tear-off feature

When you use continuous paper, the tear-off feature makes it easier to tear off the last printed sheet and save the paper normally lost between documents.

Note:

l You can tell the printer to feed the perforation of your paper to either the edge of the printer cover or approximately 80 mm (three inches) beyond, by setting the tear-off option as described in Chapter 3.

l When you set the back-feed setting to Disable in the default- setting mode, the tear-off feature does not work. For details, see Labels in this chapter or Using the Default-Setting Mode in Chapter 3.

Heres how the tear-off feature works:

1. When the printer finishes printing the last page and the print head moves to the top-of-form position on the next page, the printer automatically advances the paper to the tear-off position.

2. The READY light ( IX mode. 9

) blinks to indicate the printer is in tear-off

3. You can then easily tear off the page along the perforation.

4. When the printer receives data, it feeds the paper backward to the top-of-form position and the printer begins printing.

Removing the push tractor

1. Tear off any printed pages. Press the LF/FF and FONT buttons at the same time to feed the remaining paper backward to the paper-park position. Remove the paper from the push tractor.

Paper Handling 2-11

Using Continuous Paper with the Push Tractor

0? CAUTION: Always tear off the printed document and l excess paper before feeding paper backward. Never feed

more than one page backward through the printer.

2. Turn off the printer and lower the paper-release lever to the single-sheet position. Then pull the push tractor straight down and out of the printer.

3. Replace the paper guide.

2-12 Paper Handling

Switching Between Continuous Paper and Single Sheets When you use the push tractor, you can easily switch to single-sheet printing without removing the continuous paper supply.

Switching to single sheets

Heres how to switch from continuous paper to single sheets:

1. If you have a printed document still in the printer, tear off the printed pages and then press the LF/FF and FONT buttons at the same time to reverse the remaining paper back to the paper-park position.

0t CAUTION: l

l Always tear off printed pages before feeding paper backward; feeding too many sheets backward can cause a paper jam.

l Never feed labels backward. They can easily peel off of their backing and jam the printer. See Labels later in this chapter for information on removing labels.

2. Lower the paper-release lever to the single-sheet position.

Paper Handling 2-13

Switching Between Continuous Paper and Single Sheets

010 CAUTION: If you lower the paper-release lever while continuous paper is still loaded, the printer beeps five times and the READY light goes off. If this happens, raise the paper-release lever and press the LF/FF and FONT buttons at the same time to reverse the paper to the paper- park position. You can then lower the lever again.

3. The printer is ready to print. When it receives data, it automatically loads a single sheet from the paper cassette and begins to print.

Switching to continuous paper

To switch from single sheets back to continuous paper, follow these steps:

1. If a single sheet is in the paper path, hold the LF/FF button down to eject it.

2. Raise the paper-release lever and push it firmly into the continuous-paper position.

CAUTION: If you raise the paper-release lever when a single sheet is in the paper path, the printer beeps and the

completely. Then raise the lever again.

3. The printer is ready. When the printer receives data, it automatically loads continuous paper from the push tractor and begins to print.

2-14 Paper Handling

Printing on Special Paper In addition to printing on single sheets and continuous paper, your printer can print on a wide variety of other paper types, such as envelopes, labels, and multi-part forms. You need not adjust the printer for the paper thickness when you use these paper types.

Never move the small levers on the ends of the metal

Never move this lever.

l Disregard the numbers 0 and 1 under the printer cover on the left side. They are not necessary for printer operation.

Paper Handling 2-15

Printing on Special Paper

Envelopes

You can use the manual insertion slot to print on individual envelopes.

l Always load envelopes manually through the rear slot. To load an envelope, follow the steps described in Loading paper manually earlier in this chapter.

l Before loading an envelope, lower the flap on the printers rear slot.

l Always feed envelopes by inserting the wide edge into the printer first, as shown.

l Use envelopes under normal operating conditions only.

l Printing on the edge of an envelope can damage the print head. Make sure your software program keeps the printing entirely within the printable area of the envelope. For more information on the printable area, see the Appendix.

2-16 Paper Handling

Printing on Special Paper

Multi-part forms

You can use carbonless continuous multi-part forms of up to three parts (one original plus two copies).

l Load multi-part forms with the push tractor only. You load multi-part continuous paper the same way as ordinary continuous paper. For details, see Loading continuous paper on page 2-7.

l Use only multi-part forms joined with spot-gluing that is free of wrinkles and waves. Never print on multi-part forms joined with metal staples, tape, or continuous gluing.

l If you need to adjust the top-of-form position, use your software or change the default top-of-form position as described in Chapter 3. You may have to experiment to get the setting you want.

Labels

This printer can print on labels, but you must use the push tractor.

0t CAUTION: When you use labels, always be sure that l they are not fed backward because backward feeding can

make them peel off their backing and jam the printer.

To make sure that the labels do not peel off and jam the printer, change the back-feed setting in the default-setting mode to Disable. (For instructions, see Changing the default settings in Chapter 3.) When the back-feed setting is Disable, the printer never feeds paper backward.

The back-feed setting of Disable produces the following results:

l The printer does not feed paper to the paper-park position even if you press the LF/FF and FONT buttons.

l The tear-off feature is disabled.

Paper Handling 2-17

Printing on Special Paper

l The printer does not feed paper back to the paper-park position and then advance it to the top-of-form position between jobs even if paper is loaded when you turn on the printer.

In addition to changing the back-feed setting, also follow the instructions below when you print on labels:

l Always use labels designed for use with a tractor. Do not try to print on single-sheet labels.

l Be sure to set up the printer and paper supply as shown on page 2-7.

l Because labels are especially sensitive to extremes of temperature and humidity, use them under normal operating conditions only.

l Make sure that your printing stays entirely within the printable area of the labels because printing on the edge of a label or on the backing sheet can damage the printer. See the Appendix for more information on the printable area.

Note: When you want to remove labels from the printer, always tear off the fresh supply of labels at the rear of the printer as shown below and then press the LF/FF button to advance the remaining labels out of the printer. This is necessary to prevent the labels from being fed backward.

2-18 Paper Handling

Chapter 3

Using the Printer

Operating the Control Panel .................................................... 3-2 Lights ..................................................................................... 3-2 Buttons ................................................................................... 3-3 Other control-panel features ............................................. 3-4

Selecting Character Fonts . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-5

Using the Default-Setting Mode ............................................. 3-5 Changing the default settings ............................................ 3-7 Default settings.. ................................................................... 3-13

Maintenance and Transportation ........................................... 3-16 Cleaning the printer ............................................................. 3-16 Replacing the ribbon cartridge ........................................... 3-17 Transporting the printer ..................................................... 3-18

Troubleshooting ........................................................................ 3-19 Power supply ........................................................................ 3-20 Printing .................................................................................. 3-20 Paper handling ..................................................................... 3-24

Using the Printer 3-1

Operating the Control Panel You can control basic printer operations - line feeding, form feeding, paper loading and ejecting, and font selection -with the buttons on the control panel. The indicator lights show the printer status.

Lights

The panel lights provide information on certain printer conditions and settings.

READY light

The READY light is on when the printer is ready to receive data from the computer. It flashes briefly each time you turn on the printer. The READY light also flashes under the following conditions:

l The printer is out of paper.

l The printer is in the tear-off mode (when the push tractor is installed.)

When an error occurs, the READY light goes off.

3-2 Using the Printer

Operating the Control Panel

FONT lights

The FONT lights indicate the current font setting. These lights change when you press the FONT button. Look at the font menu on the control panel to see which font is selected. For instructions on selecting fonts with the FONT button, see page 3-5.

The FONT lights (Light 1 and Light 2) also indicate your selection in the default-setting mode. For more information about the default- setting mode, see page 3-5.

Buttons

The two buttons on the control panel perform different functions depending on the printer mode.

FONT button

Press the FONT button during normal operation to cycle through the font choices on the font menu. The two FONT lights indicate current selections. For more about choosing a font with this button, see page 3-5.

Hold down the FONT button while you turn on the printer to enter the default-setting mode. When you are in the default-setting mode, use this button to make your selection. For more information about the default-setting mode, see page 3-5.

LF/FF button

Press the LF/FF button during normal operation to feed paper line by line. Hold down the LF/FF button to load a single sheet of paper or to advance continuous paper to the next top-of-form. You can also press the LF/FF button to eject a page.

When you are in the default-setting mode, use this button to change the default settings. For more information about the default-setting mode, see page 3-5.

Using the Printer 3-3

Operating the Control Panel

PAPERPARK

If you are using continuous paper, you can press the LF/FF and FONT buttons at the same time to move the paper back to the paper-park position.

0 ? CAUTION: Never feed labels backward; they may peel 0 off their backing sheet and damage the printer. Use the

LF/FF button to feed them forward.

Other control-panel features

The control panel also gives you access to two special features:

Self Test The self test lets you check whether your printer is operating properly. To run the self test, see page 1-11.

Data dump The data dump allows advanced users to pinpoint communications problems between the printer and computer. Hold down the LF/FF and FONT buttons while turning on the printer to enter data dump mode. The printer prints the exact codes (in hexadecimal format) reaching it from the computer.

3-4 Using the Printer

Selecting Character Fonts To choose one of the fonts available with your printer, press the FONT button.

FONT

The two FONT lights come on (0) and go off (0) to indicate the current selection. The table below lists the fonts and shows how the FONT lights appear for each selection.

Font FONT Lights Light 1 Light 2

Sample

Epson NLQ Roman 0 0 ABCDEFGhiJblm0123456789

Epson NLQ Sans Serif 0 0 ABCDEFGhijklm0123456789

Epson Draft 0 0 ABCDEFGhijklm0123456789

Draft condensed 0 0 ABCDff6hijkM1234W89

l on 0 off

Using the Default-Setting Mode Your printer has internal settings that control such functions as top- of-form position and page length. These settings are called default settings because they take effect each time you turn on the printer.

Using the Printer 3-5

Using the Default-Setting Mode

For most users, the factory settings are best, but you can change these settings if necessary. The table below lists all the features you can change in the default-setting mode; the next section tells you how to change them; and the section after that describes each feature in detail.

Features

Character spacing

Shape of zero

Skip-over-perforation

Tear-off position

Auto line feed

Back feed

Character table

Page length

TOF position

Settings

10 cpi or 12 cpi

Unslashed 0 or slashed 0

Off or On

On cutter or above cutter

Off or On

Enable or disable

Italic U.S.A., Italic France, Italic Germany, Italic U.K., Italic Denmark 1, Italic Sweden, italic Italy, Italic Spain 1, PC 437, PC 850, PC 860, PC 863, PC 865, PC 437 Greek*, PC 851*, PC 852*, PC 853*, PC 855*, PC 857*, PC 861*, PC 866, PC 869*, USSR GOST, BRASCII**, or Abicomp** * Available in the European version only. ** Available in the North/South American version

only.

11, 12, 8.5, or 70/6 inches (A4)

-3, -2, -1, 0, +l, +2, or +3

Note: Most software programs control the printer features listed here. If you can use your software program to control the printer, you may never need to use the default-setting mode. In fact, you may find that your program settings override your printers default settings. See your software documentation for more information.

3-6 Using the Printer

Using the Default-Setting Mode

Changing the default settings

If you do need to change any default settings, you can do as described below. You press the control panel buttons, and the control panel lights show your selections.

Note: You can repeat steps 6 through 8 if you want to make more than one change. Also, you can turn off the printer and start over if you are not sure about a setting.

1. Make sure the printer is turned off and paper is loaded in the paper cassette. If you installed the push tractor, always use continuous paper for the default-setting mode.

2. Slide the narrow cover off of the printer cover as shown. This makes it easier to read the printed messages.

Using the Printer 3-7

Using the Default-Setting Mode

3. To enter the default-setting mode, hold down the FONT button while you turn on the printer.

The printer loads a sheet of paper automatically and prints the first instruction and a table that shows you which languages you can choose. You can print the default-setting mode messages in English, French, German, Italian, or Spanish.

4. To choose English, press the FONT button until light 1 is off and light 2 is on; then press the LF/FF button.

To choose another language, use the table below and press the FONT button until the lights indicate your selection; then press the LF/FF button.

Table A: Language selection

Language Light 1 Light 2

English OFF ON

French OFF BLINK

German ON OFF

Italian ON ON

Spanish ON BLINK

Once you press the LF/FF button, the printer prints the current default settings and the next instruction in the selected language. After printing is finished, go to the next step.

5. If you want more help text to be printed, press the FONT button. After printing is finished, go to the next step.

If you dont want the help text, press the LF/FF button. You can then go to the next step immediately.

3-8 Using the Printer

Using the Default-Setting Mode

Note: When you first use the default-setting mode, its a good idea to press the FONT button to print the help text before changing default settings. The printed text guides you through the operation. Once you are familiar with the operation, press the LF/FF button to skip printing.

6. Use Table B to choose the feature you want to change. Then press the FONT button as many times as necessary until lights 1 and 2 match your selection.

Table B: Default settings

I I I I

OFF OFF TOF position No change Change (Table E)

For example, if you want to change the character table, press the FONT button until light 1 is blinking and light 2 is on.

Using the Printer 3-9

Using the Default-Setting Mode

7. Press the LF/FF button to change the setting. The READY light turns on or off to show your selection, as indicated in Table B, and your new setting is saved automatically and remains in effect until you change it.

If you are changing the character table, page length, or TOF position, go to step 8 next. Otherwise, go to step 9.

8. If you are changing the character table, page length, or TOF position, you must make additional settings as shown in the tables below. Press the LF/FF button until light 1, light 2, and the READY light indicate your selection. Then press the FONT button to set the feature.

Once you press the FONT button, the printer advances to the next item in table B and your setting is saved automatically. The new setting remains in effect until you change it.

3-10 Using the Printer

Using the Default-Setting Mode

Table C: Character table

BLINK ON OFF PC 866 (Russian)*

BLINK ON ON USSR GOST (Russian)*

BLINK ON BLINK PC 861 (Icelandic)

* Available in the European version only. ** Available in the North/South American version only.

Using the Printer 3-11

Using the Default-Setting Mode

Table D: Page length

Light 1 Light 2

OFF OFF

OFF OFF

OFF ON

OFF ON

READY light

ON

BLINK

OFF

ON

Page length

11 inches

12 inches

8.5 inches

70/6 inches (A4)

Table E: TOF position

3-12 Using the Printer

Using the Default-Setting Mode

9. Turn off the printer to exit the default-setting mode. Any changes you have made remain in effect until you change them again.

10. After you exit the default-setting mode, slide the narrow cover back on the printer.

Default settings

This section describes all the features in the default-setting mode.

Character spacing

When you select 10 cpi, the printer prints 10 characters per inch (cpi). When you select 12 cpi, it prints 12 characters per inch.

Shape of zero

The printer prints the zero character with a slash (0) when the setting is on, or no slash (0) when the setting is off. The slashed zero allows you to easily distinguish between an uppercase 0 and a zero when printing such items as program lists.

Using the Printer 3-13

Using the Default-Setting Mode

Skip-over-perforation

When you turn on this feature, the printer skips over the perforations of continuous paper, providing a 1-inch margin between the last line printed on one page and the first line printed on the next. Because most software programs set their own top and bottom margins, you should use this feature only if your program does not provide them. This feature does not affect single-sheet paper.

Tear-off position

When you use continuous paper with the push tractor, this feature advances the paper perforation to the tear-off position where you can easily tear off the printed page. When the printer receives data, it automatically reverses the paper to the top-of-form position and starts printing, so you can use all of the next sheet.

You can choose from two tear-off positions with this feature. If you select On cutter, the printer feeds the paper perforation to the edge of the printer cover. If you select Above cutter, the printer feeds the perforation about 80 mm (3 inches) beyond the printer covers edge.

Auto line feed

When the auto line feed feature is on, each carriage return (CR) code is accompanied by a line feed (LF) code. If your printed text is unexpectedly double-spaced, set this feature to off. If text lines print on top of each other, set it to on.

Back feed

When you set this feature to Disable, the printer never feeds paper backward.

l The printer does not feed paper to the paper-park position even if you press the LF/FF and FONT buttons.

3-14 Using the Printer

Using the Default-Setting Mode

l The tear-off feature is disabled.

l The printer does not feed paper back to the paper-park position and then advance it to the top-of-form position between jobs even if paper is loaded when you turn on the printer.

Set this feature to Disable when you use labels, or when you do not want to tear off continuous paper after each print job.

Character table

Character tables contain the characters and symbols used in different languages. Your printer includes a wide variety of character tables. You can choose from these options:

Italic character table: U.S.A. l France . U.K. l Denmark 1 l Italy l Spain 1

l Germany l Sweden

Graphic character table: l PC 437 (USA, standard Europe) l PC 860 (Portuguese) l PC 865 (Nordic) l PC 851 (Greek)* l PC 853 (Turkish)* l PC 857 (Turkish)* l PC 866 (Russian)* l USSR COST (Russian)* l Abicomp

(Brazilian Portuguese)**

l PC 850 (Multilingual) l PC 863 (Canadian French) l PC437 Greek (Greek) l PC 852 (East Europe)* l PC 855 (Cyrillic)* l PC 861 (Icelandic)* l PC 869 (Greek)* . BRASCII

(Brazilian Portuguese)**

* Available in the European version only. ** Available in the North/South American version only.

See the Appendix for specific characters in these character tables.

Using the Printer 3-15

Using the Default-Setting Mode

Page length

This option is available only when you use continuous paper with the push tractor. You can set the page length to 8.5, 11, 12, or 70/6 (A4) inches.

TOF (top-of-form) position

Whenever you press the LF/FF button or send the form feed command, the printer loads paper to the top-of-form (TOF) position. The TOF position is factory set to the 0 position (8.5 mm - 0.33 inch - from the top edge of paper). You can set this position from - 3 to +3 in l-mm (0.04-inch) increments.

Maintenance and Transportation Cleaning the printer

To keep your printer operating at its best, you should clean it thoroughly several times a year.

1. Make sure the printer is turned off. Remove any paper as well as the paper cassette and output guide.

2. Use a soft brush to carefully brush away all dust and dirt.

3. If the outer case or paper cassette is dirty or dusty, clean it with a soft, clean cloth dampened with mild detergent. Keep the printer cover in place to prevent water from getting inside the printer.

3-16 Using the Printer

Maintenance and Transportation

0 t a

CAUTION: l Never use alcohol or thinners to clean the printer;

these chemicals can damage the components as well as the case.

l Do not use a hard or abrasive brush. l Do not spray the inside of the printer with lubricants;

unsuitable oils can damage the mechanism. Contact your dealer or a qualified service person if you think lubrication is needed.

l Be careful not to get water on the printer mechanism or electronic components.

Replacing the ribbon cartridge

When the printing becomes faint, you need to replace the ribbon cartridge.

We recommend that you use Epson ribbon cartridge S015047 for this printer. Genuine Epson ribbons are designed and manufactured to work properly with your Epson printer. Their high quality ensures proper operation and long life of the print head and other printer parts. Using any other ribbon may damage your printer or shorten its life.

0 t l

CAUTION: If you have just used the printer, let the print head cool for a few minutes before you touch it.

Using the Printer 3-17

Maintenance and Transportation

To remove the old ribbon cartridge, first move the print head to the center of the printer. Then remove the cartridge by lifting the posts on either side of it.

To replace the ribbon cartridge, follow the steps in Installing the Ribbon Cartridge in Chapter 1.

Transporting the printer

If you need to transport your printer some distance, carefully repack it using the original box and packing materials, as described below:

1.

2.

3.

4.

5.

Turn off the printer. Unplug the power cord from the electrical outlet; then disconnect the interface cable from the printer.

Remove the output guide and the ribbon cartridge.

Remove the push tractor, if installed.

Attach the protective materials to the printer. See page 1-3.

Repack the printer, ribbon cartridge, output guide, and power cord in the original packing materials and place them in the printers original box.

3-18 Using the Printer

Troubleshooting Most problems you may encounter while operating your printer have simple solutions. If you have a printer problem, find it in the list below and then see the appropriate page for help.

Power supply

l Power is not being supplied.

Printing

l The printer does not print. l The print is faint or uneven. l Dots are missing in printed characters or graphics. l Printed characters are not what you expected. l The print position is not what you expected.

Paper handling

l Single sheets do not feed properly from the paper cassette.

l Single sheets do not feed properly from the manual insertion slot.

l Continuous paper does not feed properly.

See 3-20.

See 3-20. See 3-21. See 3-22. See 3-22. See 3-23.

See 3-24.

See 3-25. See 3-25.

You can check the operation of your printer using the self test. See Running the Self Test in Chapter 1. If the self test works properly, the problem probably lies in the computer, the software, or the interface cable. If the self test does not work, contact your dealer or a qualified service person for assistance.

Using the Printer 3-19

Troubleshooting

Power supply

Power is not being supplied.

l The lights on the control panel do not go on.

Check that the power cord is properly plugged into the electrical outlet.

If the electrical outlet is controlled by an outside switch or automatic timer, use a different outlet.

Plug another electrical device into the outlet to determine whether the outlet is operating properly.

l The lights come on briefly and then go off The lights stay off even when the power is turned on again.

Check that the printers voltage rating matches the voltage of your electrical outlet. If the voltages do not match, unplug the printer and contact your dealer immediately. Do not reconnect the power cord to an electrical outlet.

Printing

The printer does not print.

l The READY light is on but nothing is printed.

Check that the software is installed properly for your printer. Check the softwares printer settings.

Check both ends of the interface cable between the printer and the computer. Make sure this cable is a shielded twisted- pair parallel cable that meets both the printer and computer specifications.

l The READY light is/lashing.

The printer may be out of paper. Load paper in the printer.

3-20 Using the Printer

Troubleshooting

l The printer sounds like it is printing, but nothing is printed.

The ribbon cartridge may not be installed properly. See the section on ribbon installation in Chapter 1.

The ribbon may be worn out. Replace the ribbon cartridge as described earlier in this chapter.

l The printer makes a strange noise, the beeper sounds several times, and the printer stops abruptly.

Turn off the printer and check for a paper jam, a ribbon jam, or other problems. If the printer still does not print correctly, contact your dealer.

l The beeper sounds several times and the READY light goes off.

An error has occurred. Turn off the printer and turn it on again. If the READY light stays off, contact your dealer or a qualified service person. (If an error occurs when you try to switch between single sheets and continuous paper, see page 3 - 2 6 . )

The print is faint or uneven.

l Printed characters have parts missing at the bottom.

The ribbon cartridge may not be installed properly. See the section on ribbon installation in Chapter 1.

l The printout is faint.

The ribbon may be worn out. Replace the ribbon cartridge as described earlier in this chapter.

Using the Printer 3-21

Troubleshooting

Dots are missing in printed characters or graphics.

l A line of dots is missing in the printout.

The print head is damaged. Stop printing and contact your dealer to replace it.

l Dots are missing in random positions.

Either there is too much slack in the ribbon or the ribbon has come loose. Re-install the ribbon cartridge as described in Chapter 1.

Printed characters are not what you expected.

l The typestyles or characters you sent with your software are not printed.

Check that the software is correctly configured for your printer. For instructions, see Chapter 1.

l The font selected on the control panel does not print.

Your software may be overriding your control panel setting. Check the font setting in your software program.

l The wrong characters are printed.

The wrong character table is selected. Check the default character table setting as described in Changing the default settings on page 3-7.

3-22 Using the Printer

Troubleshooting

The print position is not what you expected.

l Printing starts too high or too low on the page, or the bottom part of one page is printed at the top of the next page.

Reduce or eliminate the top margin with your application software.

Use your software to specify the type of paper you are using (single-sheet or continuous) and to reduce the lines-per-page setting.

Change the TOF position in the default-setting mode. See Changing the default settings on page 3-7.

Also, it is possible to open the printer cover and turn the gear to make minor adjustments to the loading position for the current page only. See Chapter 2.

l All the text is printed on the same line.

Set the auto line feed to on in the default-setting mode so the printer adds a line-feed code to each carriage return. See Changing the default settings on page 3-7.

l The text is printed with extra blank lines between the lines of text.

Two line-feed signals are being sent. Set the auto line feed to off in the default-setting mode. See Changing the default settings on page 3-7.

Line spacing is incorrect. Adjust the line-space setting with your software.

l Page length does not match the length of the paper.

Check the page length set by your software and adjust it if necessary.

If you are using continuous paper, change the page length in the default-setting mode. See Changing the default settings on page 3-7.

Using the Printer 3-23

Troubleshooting

l Regular gaps occur in the printout.

One-inch skip-over-perforation may be set. Set skip-over- perforation to off in the default-setting mode. See Changing the default settings on page 3-7.

Note: l You can use data dump mode to find the cause of

communication problems between the printer and your software programs. See page 3-4.

l If the printer still does not print correctly, try the self test described in Chapter 1. If the self test works properly, the printer is all right, and the problem probably lies in the computer, the software, or the cable. If the self test does not work, contact your dealer or a qualified service person.

Paper handling

Single sheets do not feed properly from the paper cassette.

l When the push tractor is installed, the platen does not rotate and paper does not feed.

Check that the paper-release lever is in the lower, single- sheet position.

l The platen rotates but paper does not feed and the READY light flashes.

The paper cassette is out of paper. Load paper in the cassette.

l Paper feeding is crooked or the paper jams.

Turn off the printer and pull out the paper. Remove the paper cassette and make sure the paper is properly loaded in the paper cassette.

l Pages do not fully eject.

Use the LF/FF button to eject the pages.

3-24 Using the Printer

Single sheets do not feed properly from the manual insertion slot.

l Paper feeding is crooked or the paper jams.

Turn off the printer and pull out the paper. Insert a new sheet straight into the paper slot. Make sure youre using the right type of paper. See the paper specifications in the Appendix.

l The paper may be too far to the right.

Move the paper a little to the left.

l The paper does not eject completely.

The paper may be too long. Use paper that is within the specified range. See the paper specifications in the Appendix.

Continuous paper does not feed properly.

When you send data or press the LF/FF button, the push tractor does not feed the paper.

Check that the paper-release lever is in the raised, continuous-paper position.

The paper has come off the push tractor. Reattach the paper to the push tractor.

l Paper feeding is crooked or the paper jams.

The position of your paper supply may be preventing it from feeding straight. Make sure the paper supply is not obstructed by a cable or some other object.

Make sure that your paper supply is positioned within 1 meter (3 feet) of the printer.

Check that the holes on the sides of the paper are aligned with each other. Also, make sure the sprocket units are locked and their covers are closed.

Check that the paper size and thickness are within the specified range. See the paper specifications in the Appendix.

Using the Printer 3-25

Troubleshooting

l The paper does not eject properly.

The page may be too long. Tear off the fresh supply of paper and eject the page from the printer. Use only paper that is within the specified length range described in the Appendix.

l When you switch between single sheets and continuous paper, the beeper sounds several times and the READY light goes off

You may have tried to change the paper-release lever position while paper remained in the printer. Return the paper-release lever to the previous position and eject paper (or feed paper to the paper-park position). Then change the paper-release lever position.

l The paper does not feed backward to the paper-park position or the tear- off feature does not work.

You may have set the back-feed setting in the default-setting mode to Disable. Set the back-feed setting to Enable. See Changing the default settings on page 3-7. However, when you print on labels, make sure you set the back-feed setting to Disable.

3-26 Using the Printer

Appendix

Technical Specifications .......................................................... A-2 Printer specifications ......................................................... A-2 Interface specifications ...................................................... A-8 Initialization ........................................................................ A-11

Command Summary ............................................................... A-13 Sending printer commands .............................................. A-13 Using the command summary ......................................... A-13 Printer operation ................................................................ A-14 Data control ........................................................................ A-14 Vertical motion ................................................................... A-14 Horizontal motion ............................................................. A-15 Overall printing style ........................................................ A-16 Print size and character width ......................................... A-16 Print enhancement ............................................................. A-17 Word processing ................................................................ A-17 Character tables .................................................................. A-18 User-defined characters .................................................... A-19 Graphics .............................................................................. A-20

Character Tables . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . A-21

Appendix A-1

Technical Specifications Printer specifications

Printing Printing method: 9-pin impact dot matrix

Printing speed:

Quality Characters/inch Characters/second/line

Draft 10 200

12 240

NLQ 10 40

12 48

Printing direction:

Line spacing:

Bidirectional logic-seeking for text printing. (Unidirectional can be selected with a software command.) Unidirectional for graphics.

l/6 inch, l/8 inch, or programmable in l/216-inch increments

Paper feed speed: 86.5 ms per l/6-inch line; 2.88 inches/second with continuous feed

Buffer:

Download memoy:

4KB

Memory capacity for 6 NLQ and 6 draft user-defined characters

Printable columns:

12cpi 96

12 cpi condensed 160

A-2 Appendix

Technical Specifications

Resident fonts:

Character tables: North/South America: Europe: Other countries:

One italic and 7 graphics character tables One italic and 15 graphics character tables One italic and 5 graphics character tables

Character sets: 13 international character sets

Paper Single skeets (Paper cassette):

Size

Thickness Weight

Input paper supply

Epson Draft Epson NLQ Roman Epson NLQ Sans Serif

US model: Letter (8.5 x 11 inches) Other models: A4 (210 x 297 mm) 0.065 to 0.14 mm (0.0026 to 0.0055 inches) 64 to 90 g/m2 (17 to 24 lb) l Use 90 g/m2 (24 lb) paper under normal

conditions.

50 sheets for 82 g/m* (22 lb) 60 sheets for 64 g/m* (17 lb) Total thickness of paper stack should be less than 5 mm (0.2 inches).

Single skeets (Manual insertion): Width 148 to 257 mm (5.8 to 10.1 inches) Length 92 to 364 mm (3.6 to 14.3 inches) Thickness 0.065 to 0.14 mm (0.0026 to 0.0055 inches) Weight 53 to 90 g/m2 (14 to 24 lb)

l Use 90 g/m2 (24 lb) paper under normal conditions.

Continuous paper: Width Copies Thickness Weight

101 to 254 mm (4 to 10 inches) Three sheets (one original plus two copies) 0.065 to 0.25 mm (0.0026 to 0.0098 inches) total 53 to 82 g/m2 (14 to 22 lb) for one sheet 40 to 58 g/m2 (12 to 15 lb) per sheet in multi-part forms l Use only two or three-part carbonless multi-part

forms and use them with the push tractor.

Appendix A-3

Technical Specifications

Single sheets (Manual insertion): Width 148 to 257 mm (5.8 to 10.1 inches) Length 92 to 364 mm (3.6 to 14.3 inches) Thickness 0.065 to 0.14 mm (0.0026 to 0.0055 inches) Weight 52 to 90 g/m2 (14 to 24 lb)

Continuous paper: Width 101 to 254 mm (4 to 10 inches) Copies Two sheets (one original plus one copy) Thickness 0.065 to 0.18 mm (0.0026 to 0.0071 inches) total Weight 52 to 82 g/m2 (14 to 22 lb) for one sheet

40 to 58 g/m2 (12 to 15 lb) per sheet in multi-part forms l Use only two-part carbonless multi-part forms and

use them only with the optional push tractor.

Note: YOU can use recycled paper under normal conditions. If you notice increases in ribbon consumption and paper jamming, use a higher grade of paper.

Labels: Size 101 to 254 mm (4 to 10 inches) width for backing

sheet

Thickness

63.5 x 23.8 mm (2 1/2x 15/16 inches) minimum for a label 0.07 to 0.09 mm (0.0028 to 0.0035 inches) for backing sheet

Weight 0.16 to 0.19 mm (0.0063 to 0.0075 inches) total 68 g/m2 (17 lb) l Use continuous type labels only with the optional

push tractor. l Use labels only under normal temperature and

humidity conditions.

Envelopes: Size No. 6

No. 10 Thickness Weight

166 x 92 mm (6.5 x 3.6 inches) 240 x 104 mm (9.4 x 4.1 inches) 0.16 to 0.48 mm (0.0063 to 0.019 inches) 45 to 75 g/m2 (12 to 20 lb) l Use envelopes only under normal temperature

and humidity conditions. l Load envelopes with the longer side inserted into

the rear slot by manual insertion only.

A-4 Appendix

Technical Specifications

Note: You can use recycled paper under normal conditions. If you notice increases in ribbon consumption and paper jamming, use a higher grade of paper.

Labels: Size 101 to 254 mm (4 to 10 inches) width for backing

sheet

Thickness

63.5 x 23.8 mm (2.50 x 0.94 inches) minimum for a label 0.07 to 0.09 mm (0.0028 to 0.0035 inches) for backing sheet

Weight 0.16 to 0.19 mm (0.0063 to 0.0075 inches) total 68 g/m2 (18 lb) l Use only continuous type labels and use them

only with the push tractor. l Use labels only under normal temperature and

humidity conditions.

Envelopes: Size No. 6

No. 10 Thickness Weight

166 x 92 mm (6.5 x 3.6 inches) 240 x 104 mm (9.5 x 4.1 inches) 0.16 to 0.48 mm (0.0063 to 0.0197 inches) 45 to 75 g/m* (12 to 20 lb) l Use envelopes only under normal temperature

and humidity conditions. l Load envelopes manually, with the longer side

inserted into the rear slot.

A-4 Appendix

Technical Specifications

Printable area: Single sheets (paper cassette and manual insertion) and envelopes

printable area

J

B

4

- C

A The minimum top margin is 8.5 mm (0.33 inches).

B The minimum left margin is 3 mm (0.12 inches). The minimum right margin is:

3.8 mm (0.15 inches) for the A4-size paper cassette 9.7 mm (0.38 inches) for the letter-size paper cassette 3 mm (0.12 inches) for manual insertion However, the maximum printable width is 203 mm (8 inches).

C The minimum bottom margin is 13.5 mm (0.53 inches).

Appendix A-5

Technical Specifications

Continuous paper

I 0-~---------- - - - - - - -

A The minimum top and bottom margins above and below the perforation are 9 mm (0.35 inches).

B The minimum left margin is 13 mm (0.51 inches). The minimum right margin is 13.8 mm (0.54 inches). The maximum printable width is 203 mm (8 inches).

Mechanical

Paper-feed methods:

Ribbon:

Friction (paper cassette and manual insertion) Push tractor Black ribbon cartridge S015047 Life expectancy: 3 million characters at 14 dots/character

MTBF:

Print head life:

Dimensions and weight:

4000 power-on hours

200 million strokes/wire

Height 130 mm (5.1 inches) Width 375 mm (14.8 inches) Depth 252 mm (9.9 inches) without push tractor

307 mm (12.1 inches) with push tractor Weight 4.5 kg (10 lb) without push tractor

4.9 kg (10.9 lb) with push tractor

A-6 Appendix

Technical Specifications

Electrical 220 V model:

Rated voltage: Input voltage range: Rated frequency range: Input frequency range: Rated current: Power consumption:

Dielectric strength

220-230V model: Rated voltage: Input voltage range: Rated frequency range: Input frequency range: Rated current: Power consumption:

Dielectric strength:

AC 120 V AC 103.5 to 132 V 50 to 60 Hz 49.5 to 60.5 Hz 1.1 A Approx. 30 W (during self-test printing in draft mode at 10 cpi) AC 1 kV rms, 1 minute or AC 1.2 kV rms, 1 second (between AC line and chassis)

AC 220-230 V AC 198 to 244 V 50 to 60 Hz 49.5 to 60.5 Hz 0.6 A Approx. 30 W (during self-test printing in draft mode at 10 cpi) AC 1.5 kV rms, 1 minute (between AC line and chassis)

240 V model: Rated voltage: AC 240 V Input voltage range: AC 216 to 264 V Rated frequency range: 50 to 60 Hz Input frequency range: 49.5 to 60.5 Hz Rated current: 0.6 A Power consumption: Approx. 30 W (during self-test printing in draft mode

at 10 cpi) Dielectric strength: AC 1.5 kV rms, 1 minute (between AC line and

chassis)

Note: Check the label on the back of the printer for the voltage of your printer.

Appendix A-7

Technical Specifications

Environmental Temperature: Operation: 5 to 35C (41 to 95F)

Storage: -20 to 55C (4 to 131F)

Humidity (without condensation): Operation: 30 to 80 % RH Storage: 5 to 85 % RH

Safety approvals Safety standards:

US model: UL1950 with D3, CSA22.2 No.220 European model: EN 60950 (Tijv, SEMKO, DEMKO, NEMKO,

SE-H)

RFI: US model: FCC part 15 subpart B class B European model: Vfg 243 (VDE 0878 part 3) EN 55022 class B

Interface specifications Your printer is equipped with an 8-bit parallel interface.

Specifications and pin assignments

The built-in parallel interface has the following characteristics:

Data format: 8-bit parallel

Synchronization: STROBE pulse

Handshake timing: BUSY and ACKNLG signals

Signal level: TTL compatible

Connector: 36-pin 57-30360 Amphenol connector or equivalent

A-8 Appendix

Technical Specifications

The table below provides the connector pin assignments and describes their respective interface signals.

Signal Return Signal Direction Description Pin Pin

1 19 STROBE IN STROBE pulse to read data. Pulse width must be more than 0.5 microseconds at the receiving terminal.

2 20 DATA 1 IN These signals represent information in 3 21 DATA 2 IN the 1 st to 8th bits of parallel data, 4 22 DATA 3 IN respectively. Each signal is at HIGH level 5 23 DATA 4 IN when data is logical 1 and LOW when 6 24 DATA 5 IN it is logical 0. 7 25 DATA 6 IN 8 26 DATA 7 IN 9 27 DATA 8 IN

1O 28 ACKNLG OUT About a 1 O-microsecond pulse. LOW indicates that data has been received and that the printer is ready to accept more data.

11 29 BUSY OUT A HIGH signal indicates that the printer cannot receive data. The signal goes HIGH in the following cases: 1) During data entry 2) During printing 3) During an error state

12 30 PE OUT A HIGH signal indicates that the printer is in a paper-out state or in an error state.

13 - SLCT OUT Pulled up to 5V through 1.0 KR resistance.

14 - AUTO IN When this signal is LOW, the paper is FEED- automatically fed one line after printing. x-r (The signal level can be fixed to this

by setting Auto Line Feed on in the default-setting mode.)

15 - - - Not used

16 - GND - Logic ground level

17 - CHASSIS - Printers chassis ground, which is GND isolated from the logic ground

Appendix A-9

Technical Specifications

Signal Pin

Direction

32

35

36

Return Pin

16

-

Signal

GND

INIT

ERROR

GND

+5v

-

-

IN

OUT

OUT

- -

Description

Not used

Twisted-pair return signal ground level.

When this level becomes LOW, the printer controller is reset to its power-up state and the print buffer is cleared. This level is normally HIGH; its pulse width must be more than 50 microseconds at the receiving terminal.

This level becomes LOW when the printer is: 1) in a paper-out state 2) in an error state

Same as for pins 19-30.

Not used

Pulled up to 5V through 1.0 KQ resistance.

Not used

Note: l The column heading Direction refers to the direction of signal flow as

viewed from the printer. l Return denotes the twisted-pair return, to be connected at signal ground

level. For the interface wiring, be sure to use a twisted-pair cable for each signal and to complete the connection on the return side.

l All interface conditions are based on the TTL level. Both the rise and fall times of each signal must be less than 0.2 microseconds.

l Data transfer must be carried out by observing the ACKNLG or BUSY signal. Data transfer to this printer can be carried out only after receipt of the ACKNLG signal or when the BUSY signal is LOW.

A-10 Appendix

Technical Specifications

Interface timing

The figure below shows the timing for the parallel interface.

BUSY

ACKNLG

DATA

STROBE

Initialization

The printer can be initialized (returned to a fixed set of conditions) in three ways:

Hardware initialization l The power is turned on.- * The printer receives an INIT signal from the parallel

interface (pin 31 goes LOW).

Software initialization l Software sends the ESC @ (initialize the printer) command.

Appendix A-11

Technical Specifications

Default settings

The table below shows the default settings that take effect when the printer is initialized.

Item

Top-of-form position

Default setting

Current paper position or setting in the default- setting mode.

Page length Single sheets: 65 lines for A4-size paper, 61 lines for letter-size paper, 22 inches for manual insertion

Left and right margins

Line spacing

Horizontal tab positions

Font selection

Special printing effects

Download character set

Continuous paper: Subject to control panel setting in the default-setting mode

Cancelled

1/6-inch line spacing

Every eight characters

Last font selected on control panel

Cancelled (except condensed printing)

Hardware initialization: cleared Software initialization: deselected only

In addition, hardware initialization clears the data buffer.

A-12 Appendix

Command Summary Sending printer commands

Most actions your printer performs are handled by your software. Software commands instruct the printer to print in a particular typeface, feed the paper a certain amount after printing each line, start printing on a particular place on the page, and so on.

Some software programs let you send these commands yourself. This allows you to enhance your text in ways that may not normally be available through the software. For example, some word processing programs do not offer italics, but by inserting a command in your document, you can use italics anywhere you like. The commands your printer recognizes are listed in this command summary.

How you format commands depends on the software you are using. Some software programs accept only the decimal format, while others let you type in ASCII characters. (Some programs dont let you insert printer commands at all.) In addition, your software probably specifies certain punctuation you must use to enter the command. If your software allows you to send commands to the printer, the software manual should explain exactly what format and punctuation are required.

Using the command summary

The following section lists and describes all the commands by topic. If a command has no parameters, it is merely listed. If it has parameters, they are explained. The parameters are indicated by lowercase italicized letters, usually II. The examples below show how the parameters are indicated.

ESC @ is a command with no parameters.

ESC U l/0 is a command that uses 1 to turn the feature on and 0 to turn it off.

ESC K nl n2 is a command with two parameters.

ESC D nn is a command with a variable number of parameters.

Appendix A-13

Command Summa y

Printer operation

ASCII D e c . Hex.

ESC @ 64 40

DC1 17 11

DC3 19 13

ESCs1/0 115 73

ESC< 60 3C

ESC U 1/0 85 55

ESC 8 56 38

ESC 9 57 39

ESC EM n 25 19

BEL 7 07

Data control

ASCII Dec. Hex.

Description

Initialize Printer

Select Printer

Deselect Printer

Turn Half-Speed Mode On/Off

Select Unidirectional Mode (one line)

Turn Unidirectional Mode On/Off

Disable Paper-Out Detection

Enable Paper-Out Detection

Control Paper Loading/Ejecting n = R Ejecting a sheet

Beeper

Description

CR

CAN

DEL

13 OD

24 18

127 7F

Carriage Return

Cancel Line

Delete Character

Vertical motion

ASCII

FF

ESC C n

Dec. Hex.

12 0C

67 43

Description

Form Feed

Set Page Length in Lines n = Number of lines

A-14 Appendix

Command Summa y

ASCII Dec. Hex. Description

ESC C 0 n 67 43

ESC N n 78 4E

ESC O 79 4F

LF 10 OA

ESC 0 48 30

ESC l 49 31

ESC 2 50 32

ESC 3 n 51 33

ESC A n 65 41

ESC J n 74 4A

VT 11 OB

ESC B nn 66 42

ESC b c nn 98

47

62

ESC /c 2F Select Vertical Tab Channel

Set Page Length in Inches n = Number of lines

Set Skip-Over-Perforation n = Number of lines

Cancel Skip-Over-Perforation

Line Feed

Select l/8-inch Line Spacing

Select 7/72-inch Line Spacing

Select l/6-inch Line Spacing

Select n/216-inch Line Spacing

Select n/72-inch Line Spacing

Perform n/216-inch Line Feed

Tab Vertically

Set Vertical Tabs Up to 16 tabs entered in ascending order; last n should be 0

Set Vertical Tabs in Channels Same as ESC B, except that c selects a channel for the vertical tabs, which must be between 0-7.

Horizontal motion

ASCII Dec. Hex. Description

ESC l n 108 6C Set Left Margin n = Left margin column

ESC Q n 81 51 Set Right Margin n = Right margin column

BS 8 08 Backspace

Appendix A-15

Command Summary

ASCII Dec. Hex. Description

ESC e 0 n 101 65

ESCeln 101 65

ESCfOn 102 66

ESCfln 102 66

HT 9 09

ESC D nn 68 44

Overall printing style

ASCII Dec. Hex.

Set Horizontal Tab Increments n = Horizontal tab interval in spaces (n 21 at 10 cpi, 25 at 12 cpi, or 36 in

condensed modes)

Set Vertical Tab Increments n = Vertical tab interval in lines

Horizontal Skip n = Number of spaces to skip

Vertical Skip n = Number of lines to skip

Tab Horizontally

Set Horizontal Tabs Up to 32 tabs entered in ascending order; last n should be 0

Description

ESCxn 120 78 Select NLQ or Draft n = l : N L Q

0: Draft

ESCkn 107 6B Select NLQ Font n = 0: Roman

1: Sans Serif

ESC ! n 33 21 Master Select To find the value of n, add together the numbers of the typestyles you want to combine from the list below: n = 0: 10 cpi 16: Double-strike

1: 12 cpi 32: Double-width 4: Condensed 64: Italic 8: Emphasized 128: Underline

A-16 Appendix

Command Summary

Print size and character width

ASCII Dec. Hex. Description

ESC P 80 50

ESC M 77 4D

SI 15 OF

ESC SI 15 OF

DC2 18 12

so 14 OE

ESC SO 14 OE

DC4 20 14

ESC W l/O 87 57

Print enhancement

ASCII Dec. Hex.

Select 10 cpi

Select 12 cpi

Select Condensed Mode

Select Condensed Mode

Cancel Condensed Mode

Select Double-Width Mode (one line)

Select Double-Width Mode (one line)

Cancel Double-Width Mode (one line)

Turn Double-Width Mode On/Off

Description

ESC E 69 45

ESC F 70 46

ESC G 71 47

ESC H 72 48

ESC SO 83 53

ESC S1 83 53

ESC T 84 54

ESC 4 52 34

ESC 5 53 35

ESC - l/0 45 2D

Select Emphasized Mode

Cancel Emphasized Mode

Select Double-Strike Mode

Cancel Double-Strike Mode

Select Superscript Mode

Select Subscript Mode

Cancel Superscript/Subscript Mode

Select Italic Mode

Cancel Italic Mode

Turn Underline Mode On/Off

Appendix A-17

Command Summary

Word processing

ASCII Dec.

ESC a n 97

Hex.

61

Description

NLQ Justification n = 0: Left justification

1: Centering 2: Right justification 3: Full justification

Character tables

ASCII Dec. Hex. Description

ESCtn 116 74 Select Character Tables Selects character table n assigned by ESC ( t n = 0, 1, 48, 49 only

ESC(tnn 40 116 2874 Assign Character Table ESC(t3Odld2d3 Assign character table set with d2 and d3 to table dl dl = 0, 1,48, or 49 d2 d3 Character table

0 0 Italic 1 0 PC437 (USA) 1 16 PC437 Greek (Greek)* 3 0 PC850 (Multilingual) 4 0 PC851 (Greek)* 5 0 PC853 (Turkish)* 6 0 PC855 (Cyrillic)* 7 0 PC860 (Portuguese)* 8 0 PC863 (Canadian-French) 9 0 PC865 (Nordic)

10 0 PC852 (East Europe)* 11 0 PC857 (Turkish)* 14 0 PC866 (Russian)* 15 0 PC869 (Greek)* 16 0 USSR GQST (Russian)* 24 0 PC861 (Icelandic)* 25 0 BRASCII (Brazilian Portuguese)** 26 0 Abicomp (Brazilian Portuguese)** * Available in European version only *+ Available in North/South American

version only

A-18 Appendix

Command Summary

ASCII Dec.

ESC R n 82

Hex.

52

Description

Select an International Character Set n=0:USA 7: Spain I

1: France 8: Japan 2: Germany 9: Norway 3: U.K. 10: Denmark II 4: Denmark I 11: Spain II 5: Sweden 12: Latin America 6: Italy

ESC 6

ESC 7

54 36 Printable Code Area Expansion

55 37 Enable Upper Control Codes

User-defined characters

ASCII Dec. Hex. Description

ESC & nn 38 26 Define User-Defined Characters ESC & 0 nl n2 al dd n1 = Code for first character (58-63) n2 = Code for last character (58-63) al = Use top (128) or bottom (0) 8 pins of print

head dd = In draft mode, 1 byte is required for each

of the 11 columns of each character being defined. In NLQ mode, 3 bytes are required for each of the 11 columns of each character being defined.

ESC: 0 n 0 58 3A Copy ROM into RAM n = 0: Roman

1: Sans Serif

ESC % n 37 25 Select User-Defined Set n = 0: Normal set

1: User-defined set

Appendix A-19

Command Summary

Graphics

ASCII Dec. Hex. Description

ESC K nl n2 75 4B

ESC L nl n2 76 4C

ESC Y nl n2 89 59

ESC Z nl n2 90 5A

ESC * m nl n2 42 2A

Select Single-Density Graphics Mode Total columns = nl + (n2 x 256)

Select Double-Density Graphics Mode Total columns = nl + (~22 x 256)

Select High-Speed Double-Density Graphics Mode Total columns = nl + (n2 x 256)

Select Quadruple-Density Graphics Mode Total columns = nl + (n2 x 256)

Select Graphics Mode Total columns = nl + (n2 x 256)

Option Alternate code

m Horiz. density (dots/in.)

Single-density ESC K 0 60 I I I I

Double-density ESC L 1 120 I I I I

High-speed double-density* ESC Y 2 120

Quadruple-density* ESC Z

CRT I none

Plotter (1 : 1) none

CRT II none

* Adjacent dots cannot be printed in this mode.

3 240

4 80

5 72

6 90

ESC ? s n 63 3F Reassign Graphics Mode s is the character (K, L, or Z) to be reassigned to mode n (0-6)

ESC A m nl n2 94 5E Select 9-Pin Graphics Mode m: Print density (0 for single, 1 for double) Total columns = nl + (7-22 x 256)

A-20 Appendix

Character Tables You can select these character tables with the default-setting mode or by using a software command.

All tables except the italic character table are the same as the PC 437 table for hex codes 00 through 7F, so only the PC 437 and italic tables are shown completely. The rest of the tables show only the characters for hex codes 80 through FF.

The tables with * after the table name are available in the European version only; those with ** are available in the North/South American version only.

PC 437 (USA, standard Europe)

Appendix A-21

Character Tables

PC 850 (Multilingual)

0 1 2 3 4 5 6 7 8 9 A B C D E F

PC 863 (Canadian-French) PC 865 (Nordic) /

0 1 2 3 4 5 6 7 8 9 A B C D E F

BQABCDEF c E : ?: L 101 5

PC 860 (Portuguese)

0 1 2 3 4 5 6 7 8 9 A B C D E F

89ABCDEF c fi 6 .;: L I a f

0 1 2 3 4 5 6 7 8 9 A B C D E F

BQABCDEF c g g ::< L A (L z

A-22 Appendix

Character Tables

PC 437 Greek (Greek) PC 851 (Greek)

0 1 2 3 4 5 6 7 8 9 A B C D E F

PC 852 (East Europe)

70 1 2 3 4 5 6 7 8 9 A B C D E F

0 1 2 3 4 5 6 7 8 9 A B C D E F

T

,

PC 853 (Turkish)*

0 1 2 3 4 5 6 7 8 9 A B C D E F

Appendix A-23

Character Tables

PC 855 (Cyrillic)* PC 857 (Turkish)*

0 1 2 3 4 5 8 7 8 9 A B C D E F

I

8 9 A B C D E F tjrna:L.H-

PC 861 (Icelandic)* PC 866 (Russian)*

0 1 2 3 4 5 8 7 8 9 A B C D E F

BgABCDEF c $ 6 1::: L I a *

. ....

0 1 2 3 4 5 8 7 8 9 A B C D E F

8 9 A B C D E F c fi 6 :? L Q 6 -

0 1 2 3 4 5 8 7 8 9 A B C D E F

8 9 A B C D E F

A P a ...

A-24 Appendix

Character Tables

PC 869 (Greek)* USSR GOST (Russian)*

0 1 2 3 4 5 8 7 8 9 A B C D E F

89ABCDEF ^r *c j:.. L T f -:

BRASCII (Brazilian Portuguese)**

0 1 2 3 4 5 8 7 8 9 A B C D E F

0 1 2 3 4 5 8 7 8 9 A B C D E F

FgABCDEF

t c r APapti

I I B C 6 c b

I

BTBT, L Lryry\ I - A@n9'

1IIEXex\

1

111

xllxu-, 3 v 3 4: + HlIl~mt

B 9 A m 1 K'bKsI n H Jl bl f Mfz~Ybh H3H 9 U OIOOIO~ II II n II

Abicomp (Brazilian Portuguese)**

0 1 2 3 4 5 8 7 8 9 A B C D E F

Appendix A-25

Glossary

The following definitions apply specifically to printers. If a word is italicized, see that topic for more information.

ASCII American Standard Code for Information Interchange. A standardized coding system for assigning numerical codes to letters and symbols.

bidirectional printing Printing in which the print head prints in both directions. This increases the speed of printing.

bit A binary digit (0 or l), which is the smallest unit of information used by a printer or computer.

buffer The portion of the printers memory used to store data before printing it.

byte A unit of information consisting of eight bits.

characters per inch cpi) A measure of the size of text characters, sometimes referred to as pitch. The printers default setting is 10 cpi.

character table A collection of letters, numbers, and symbols that provides you with the characters used in a particular language.

condensed printing Printing in which the width of each character is approximately 60% of the width of standard characters. Useful for fitting wide tables or spreadsheets onto a page.

continuous paper Paper that has sprocket-feed holes on each side, is perforated between pages, and is supplied in a folded stack. Also called fanfold paper.

control code Special codes used to control printer functions (such as a carriage return or line feed) instead of printing characters.

Glossary GL-1

cpi See characters per inch.

data dump A troubleshooting feature that helps advanced users find the cause of communication problems between the printer and the computer. When the printer is in data dump mode, it prints each code it receives in hexadecimal notation and ASCII characters.

default A value or setting that takes effect when the equipment is turned on, reset, or initialized.

dot matrix A method of printing in which each letter or symbol is formed by a pattern (matrix) of individual dots.

double-width printing Printing in which each character is twice as wide as normal.

draft printing One of two print qualities available on your printer. Draft uses a minimum number of dots per character for high-speed printing. See also NLQ printing.

ESC/P Abbreviation for Epson Standard Code for Printers. This system of commands gives you software control of your printer from your computer. It is standard for all Epson printers and supported by most application software for personal computers.

font A font is a style of type designated by a family name.

form feed A control code and control panel button that advances the paper to the next top-of- form position.

initialization Returns the printer to its defaults (fixed set of conditions).

interface The connection between the computer and the printer. A parallel interface transmits data one character or code at a time, and a serial interface transmits data one bit at a time.

GL-2 Glossary

italic A typestyle in which the characters slant. This sentence is italicized.

line feed A control code that advances the paper one line space.

NLQ printing One of two print qualities available on your printer. Near letter quality provides better readability and appearance at a reduced print speed. See also draft printing.

paper-park position The position in which the paper is backed out of the paper path but is still attached to the push tractor.

parallel interface See interface.

printable area The area of a page on which the printer can print. It is smaller than the physical size of the page due to margins.

push tractor A detachable device that automatically pushes continuous paper into the printer from the loading side.

RAM Random Access Memory. The portion of the printers memory used as a buffer and for storing user-defined characters. All data stored in RAM is lost when the printer is turned off.

reset To return a printer to its defaults either by sending a command, an INIT signal, or by turning the printer off and then back on.

self test A method for checking the operation of the printer. When you run the self test, the printer prints the characters stored in its ROM.

software program A software program that helps you carry out a particular task, such as word processing or financial planning.

Glossary GL-3

subscript Printing in which each character is printed at about two-thirds the normal height in the lower part of the character space.

superscript Printing in which each character is printed at about two-thirds the normal height in the upper part of the character space.

tear-off A paper feed operation that automatically feeds the perforation of continuous paper to the tear-off position and then feeds the paper back to the loading position.

tear-off position The position the printer feeds the paper to at the end of print job. You can change the position in the default-setting mode so that the papers perforation meets the printers tear-off edge or passes approximately 80 mm (3 inches) beyond the edge.

top-of-form The position on the paper that the printer recognizes as the first printable line.

unidirectional printing Printing in which the print head prints in one direction only. Unidirectional printing is useful for printing graphics because it allows more precise vertical alignment than bidirectional printing.

user-defined characters Characters that are defined and stored in the printer by the user. Also called download characters.

GL-4 Glossary

Index

Command descriptions are not indexed here.

A Application program, see Software Auto line feed, 3-6, 3-9, 3-14

B Back feed, 2-17 -18, 3-6,3-9,3-14 Bidirectional printing, A-2 Buffer, A-2 Buttons, 3-2, 3-3 -4

C Cable parallel interface, 1-11 -13

Cable clip, 1-2, 1-12 Cassette, paper, 1-3,1-9 -10 Character

fonts, 3-3, 3-5, A-3 tables, 3-6, 3-9, 3-11, 3-15, A-3, A-21 -26

Cleaning the printer, 3-16 Clip, cable, 1-2, 1-12 Connecting the printer, 1-11 -13 Continuous paper, 2-5 -14, A-3, A-6 loading, 2-7 -9 top-of-form, 2-10, 3-6, 3-9, 3-12, 3-16

Control panel, 3-2 -4 Copy capacity, 2-17, A-3

D Data dump, 3-4 Default settings, 3-5 -16, A-12 setting mode, 3-5 -16

Download, A-2 Draft, 3-5, A-2, A-3

E Envelopes, 2-16, A-4 loading, 2-16 specifications, A-4

ESC/P, 1, A-13 -20

F Fonts, 3-2, A-3 button, 3-2, 3-3, 3-5 draft, 3-5, A-3 draft condensed, 3-5 Epson NLQ Roman, 3-5, A-3 Epson NLQ Sans Serif, 3-5, A-3 lights, 3-2, 3-5 selecting, 3-5

Form length, continuous paper, 3-6, 3-9, 3-12, A-3

Forms, multi-part, 2-17, A-3

G Gear, 2-2, 2-10 Graphics print direction, A-2 Guide, output, 1-8

H Help, where to get for USA users, iv Hex dump, see Data dump

I Initialization, A-11 Input buffer, A-2 Interface connecting, 1-11 -13 specifications, A-8 -11

Index IN-1

J Jam, paper, 2-16, 3-21

L Labels, 2-17 -18, A-4 Lever paper-release, 2-5, 2-6, 2-12, 2-13, 2-14

LF/FF button, 3-3 Loading paper continuous paper, 2-7 -9 envelopes, 2-16 labels, 2-17 -18 manually, 2-3 -4 single sheets, 1-8 -10

M Maintenance, 3-16 -18 Manual loading, 2-3 -4 Moving the printer, 3-18 Multi-part forms, 2-17, A-3

N NLQ printing, 3-5, A-2

0 Output guide, 1-8

P Packing materials, 1-3, 3-18 Page length continuous paper, 3-9, 3-12, A-3 manual insertion, A-3 single sheets, A-3

Paper continuous, A-3 jam, 2-16, 3-21 single sheet, A-3

Paper cassette, 1-3, 1-9 -10 Paper guide, 2-5, 2-12

Paper-park position, 2-10, 2-13, 3-4 Paper-release lever, 2-5, 2-6, 2-12, 2-13,

2-14 Paper support, 1-9, 2-3 Parallel interface, 1-11 -13, A-8 -11 Plugging in the printer, 1-7 -8 Power supply, see Voltage Printable area, A-5 -6 Print direction, A-2 Printer stand, 1-5 Problems, see Troubleshooting Protective materials replacing, 3-18 removing, 1-3

Push tractor, 2-5 -14 installing, 2-5 -6 loading paper, 2-7 -9

R READY light, 3-2 Ribbon problems with, 3-21, 3-22 Ribbon cartridge installing, 1-5 -7 replacing, 3-17 -18 specifications, A-6

S Safety approvals, A-8 Safety information for UK users, vi Safety instructions, iii - iv Self test, 1-8 -11, 3-4 Single sheets, tips for, 2-2 -3 see also Loading paper

Skip-over-perforation, 3-6, 3-9, 3-14 Software, 1-13 -14 Special paper, 2-15 -18 Specifications, A-2 -12 Stand, printer, 1-5 Switching between continuous and single sheet, 2-13 -14

IN-2 Index

T Tear off, 2-11, 3-6, 3-9, 3-14 adjusting, 2-11 position, 3-6, 3-9, 3-14

Testing the printer, 1-8 -11, 3-4 Toll-free number for USA users, iv Top-of-form position, 2-10, 3-6, 3-9,

3-12, 3-16 Tractor, push, 2-5 -14 installing,, 2-5 -6 loading paper, 2-7 -9

Transporting the printer, 3-18 Troubleshooting, 3-19 -26 Typestyles, 3-5, A-3

U Unidirectional printing, A-2 Unpacking the printer, 1-2 -3

V Voltage, 1-2, A-7 power supply, A-7

w Weight, 1-5, A-6 Where USA users can get help, iv

Index IN-3

IN-4 Index