Contents

Epson ELPMBP02 Installation Manual PDF

1 of 6
1 of 6

Summary of Content for Epson ELPMBP02 Installation Manual PDF

Model: ELPMBP02 This product is UL Listed. It must be installed by a qualified professional installer.

Installation and Assembly: False Ceiling Plate Kit

3215 W. North Ave. Melrose Park, IL 60160 (800) 865-2112 or (708) 865-8870 Fax: (708) 865-2941 www.peerlessmounts.com

Maximum UL Load Capacity: 50 lb (22.6 kg)

Manufactured by Peerless Industries, Inc.

ISSUED: 02-13-08 SHEET #:128-9030-2 07-16-082 of 6 Visit the Peerless Web Site at www.peerlessmounts.com For Technical Support Contact Peerless Mounts at 1-800-729-0307 or 708-865-8870.

Table of Contents Parts List .............................................................................................................................................................................. 3

Mounting Above Ceiling Tile, Mounting in Place of Ceiling Tile and Attaching Ceiling Tray to Filler Tray ............................... 4

Anchoring Methods ............................................................................................................................................................... 5

Warranty Information ............................................................................................................................................................. 6

NOTE: Read entire instruction sheet before you start installation and assembly.

Do not begin to install your product until you have read and understood the instructions and warnings contained in this Installation Sheet. If you have any questions regarding any of the instructions or warnings, call Peerless customer care at 1-800-729-0307.

This product should only be installed by someone of good mechanical aptitude, has experience with basic building construction, and fully understands these instructions.

Make sure that the supporting surface will safely support the combined load of the equipment and all attached hard- ware and components.

Never exceed the Maximum UL Load Capacity. If mounting to wood joists or wood beam ceilings, make sure that mounting screws are anchored into the center of the

joists or beams. Use of an "edge to edge" stud finder is highly recommended. Always use an assistant or mechanical lifting equipment to safely lift and position equipment. Tighten screws firmly, but do not overtighten. Overtightening can damage the items, greatly reducing their holding

power. This product is intended for indoor use only. Use of this product outdoors could lead to product failure and personal

injury. When installing or adjusting the ceiling mount, do not use adhesives, lubricants or oils to prevent the screws from

loosening. If you use adhesives, lubricants, or oils to prevent the screws from loosening, the casing may crack and the projector may fall, causing serious injury and damage to the projector.

WARNING

Tools Needed for Assembly stud finder ("edge to edge" stud finder is recommended) phillips screwdriver hammer wire cutters drill 1/4" bit for concrete surface 5/32" bit for wood studs

ISSUED: 02-13-08 SHEET #:128-9030-2 07-16-083 of 6 Visit the Peerless Web Site at www.peerlessmounts.com For Technical Support Contact Peerless Mounts at 1-800-729-0307 or 708-865-8870.

A1

NOTE: Some parts may appear slightly different than illustrated.

Before you begin, make sure all parts shown are included with your product.

DB C

A

LKF

M AA BB

CC

IMPORTANT PRE-ASSEMBLY INFORMATION: Ceiling Trays (A), and (A1) are designed to fit within or above a 24" (610 mm) x 24" (610 mm) section of a conventional suspended ceiling system. It may also be mounted within or above 24" x 48" conventional suspended ceiling. Ceiling runners (see DETAIL 1, page 5) should have a "T" cross section and a minimum height of 1.5" (38 mm).

For certain installations it may be best to install ceiling anchors (step 2) before installing the ceiling tray (step 1).

Description Qty. Part # A ceiling tray 1 128-2198 A1 filler tray 1 128-2207 B 1/4"-20 x 3/8" screws 4 520-2015 C 1/4"-20 nuts 4 530-9302 D allen wrench 1 560-9706 F turnbuckle 4 560-9620 G 12 gauge x 20' (6.1m) tie wire (not shown) 1 600-2008 K eye bolt 5 580-0006 L concrete anchor 5 580-0005 M flush mount tube 1 1446-014 AA M5 x 10 mm socket screw 4 520-1216 BB nut 4 530-9409 CC 3 mm allen wrench 1 560-0194

Parts List

ISSUED: 02-13-08 SHEET #:128-9030-2 07-16-084 of 6 Visit the Peerless Web Site at www.peerlessmounts.com For Technical Support Contact Peerless Mounts at 1-800-729-0307 or 708-865-8870.

1 Remove 24" x 24" or 24" x 48" false ceiling tile.

If using 24" x 48" ceiling tile, cut one tile in half and add another 24" ceiling runner in order to make a 24" x 24" section.

Place ceiling tray (A) in 24" x 24" grid with hole to center, left, or right.

Place filler (A1) tray into gap.

For Mounting in Place of Ceiling Tile

1-1

1-2

1-3

2 Attach ceiling tray (A) to filler tray (A1) using four bolts (B) and nuts (C) as shown in fig. 1.1. Hook turnbuckles (F) into ceiling tray (A). Hook one turnbuckle through filler tray (A1) and ceiling tray (A) where indicated by gray rectangles in illustration below.

OPTION 2: Use M5 x 10 mm socket screws (AA) and M5 nuts (BB) to attach ceiling tray (A) to filler tray (A1) in place of fasteners 1/4"-20 x 3/8" screws (B) and 1/4"-20 nuts (C) if neces- sary. Tighten M5 x 10 mm socket screws (AA) using 3 mm allen wrench (CC).

Attaching Ceiling Tray to Filler Tray

A F

A A1

C or BB

B or AA

Gray rectangles show correct positions for turnbuckles (F).

A A1

For Mounting Above Ceiling Tile Place ceiling tray (A) in grid above 24" x 24" or 24" x 48" false ceiling tile with hole to center, left or right.

Place filler (A1) tray into gap.

Once placed where needed, through hole in ceiling tray (A), mark on false ceiling tile where hole will be.

Cut out 2.25" hole in false ceiling tile. (Escutcheon Ring Accessory (ACC 640) is recommended).

For flush mounting applications: From the top down, thread the flush mount tube (M) down through the retaining collar in ceiling tray (A).

NOTE: Set screw included with projector mount will be installed according to the instructions provided with the mount.

Skip to step 2.

1-4

1-3

1-2

1-1

1

1-5

A

M

A1CEILING RUNNER

fig. 1.1

ISSUED: 02-13-08 SHEET #:128-9030-2 07-16-085 of 6 Visit the Peerless Web Site at www.peerlessmounts.com For Technical Support Contact Peerless Mounts at 1-800-729-0307 or 708-865-8870.

Cut tie wire (G) into four pieces of equal length. Insert wires through the ends of the turnbuckles and loop to prevent the wire from slipping. Twist each wire around itself at least six times as tightly as possible.

Drill holes for four ceiling anchors (see Various Anchoring Methods). Position the holes so when the tie wires are attached and taut the optimal angle is 15 (see figure 3.1 for reference). Unit may be mounted at an angle up to 45 if necessary. Pull tie wires tight and loop through turnbuckles of the ceiling anchors (or truss). Again twist each wire around itself at least six times as tightly as possible. When this step is complete, the weight of the ceiling tray should be supported by the tie wires. NOTE: 20' (6.1 m) of tie wire (G) is provided. If space between the true ceiling and suspended ceiling is more than 36" (914 mm), additional wire (12 gauge annealed, steel, black) will be needed.

VARIOUS ANCHORING METHODS

Wood Joists or Beams Drill 5/32" (4 mm) dia. holes 2" (51 mm) deep. Fully insert eye bolts (K).

Solid Concrete Drill 1/4" (6 mm) dia. holes 1.5" (38 mm) deep. Hammer in Concrete Anchor (L) using Rawl #3250 setting tool or equivalent.

K L

Truss Ceiling No anchor required. After attaching tie wire to turnbuckle loop upper end around ceiling truss. Pull tie wire tight and twist it around itself at least six times as tightly as possible..

A

G G

G G

Knockout panels are provided for electrical outlet boxes and antenna leads.

A1

Suspended Ceiling Kit installation is now complete. After all components (Projector Mount, Extension Column, etc.) and equipment have been attached, tension the tie wires by adjusting turnbuckles (F). Load must be carried by tie wires - not suspended ceiling runners.

Installer must verify that the ceiling will safely support four times the combined weight of all attached equipment and hardware.

Never attach hooks to filler tray.

WARNING

15

fig. 3.1

3

3-1

Anchoring Methods

2" 2"

1.5"

CEILING RUNNER

DETAIL 1

ISSUED: 02-13-08 SHEET #:128-9030-2 07-16-086 of 6 Visit the Peerless Web Site at www.peerlessmounts.com For Technical Support Contact Peerless Mounts at 1-800-729-0307 or 708-865-8870.

LIMITED FIVE-YEAR WARRANTY

2007 Peerless

Manualsnet FAQs

If you want to find out how the ELPMBP02 Epson works, you can view and download the Epson ELPMBP02 Installation Manual on the Manualsnet website.

Yes, we have the Installation Manual for Epson ELPMBP02 as well as other Epson manuals. All you need to do is to use our search bar and find the user manual that you are looking for.

The Installation Manual should include all the details that are needed to use a Epson ELPMBP02. Full manuals and user guide PDFs can be downloaded from Manualsnet.com.

The best way to navigate the Epson ELPMBP02 Installation Manual is by checking the Table of Contents at the top of the page where available. This allows you to navigate a manual by jumping to the section you are looking for.

This Epson ELPMBP02 Installation Manual consists of sections like Table of Contents, to name a few. For easier navigation, use the Table of Contents in the upper left corner.

You can download Epson ELPMBP02 Installation Manual free of charge simply by clicking the “download” button in the upper right corner of any manuals page. This feature allows you to download any manual in a couple of seconds and is generally in PDF format. You can also save a manual for later by adding it to your saved documents in the user profile.

To be able to print Epson ELPMBP02 Installation Manual, simply download the document to your computer. Once downloaded, open the PDF file and print the Epson ELPMBP02 Installation Manual as you would any other document. This can usually be achieved by clicking on “File” and then “Print” from the menu bar.