Epson ELPDC05 User's Guide PDF

Epson

ELPDC05 High Resolution Document Camera

Users Guide

2

Important Safety Information WARNING: Never open any cover on the document camera. Dangerous electrical voltages inside the document camera can severely injure you. Do not attempt to service this product yourself. Refer all servicing to qualified service personnel.

WARNING: The document camera and its accessories come packaged in plastic bags. Keep plastic bags away from small children to avoid any risk of suffocation.

WARNING: Never attempt to replace the lamps. Refer all lamp servicing to qualified service personnel.

Copyright Notice All rights reserved. No part of this publication may be reproduced, stored in a retrieval system, or transmitted in any form or by any means, electronic, mechanical, photocopying, recording, or otherwise, without the prior written permission of Seiko Epson Corporation. The information contained herein is designed only for use with this Epson product. Epson is not responsible for any use of this information as applied to other products.

Neither Seiko Epson Corporation nor its affiliates shall be liable to the purchaser of this product or third parties for damages, losses, costs, or expenses incurred by purchaser or third parties as a result of: accident, misuse, or abuse of this product or unauthorized modifications, repairs, or alterations to this product, or (excluding the U.S.) failure to strictly comply with Seiko Epson Corporations operating and maintenance instructions.

Seiko Epson Corporation shall not be liable for any damages or problems arising from the use of any options or any consumable products other than those designated as Original Epson Products or Epson Approved Products by Seiko Epson Corporation.

Responsible Use of Copyrighted Materials Digital cameras, scanners, and ink jet printers, like conventional photocopiers and cameras, can be misused by improper copying or printing of copyrighted material. While some countries laws permit limited copying of copyrighted material in certain circumstances, those circumstances may not be as broad as some people assume. Epson encourages each user to be responsible and respectful of the copyright laws when using digital cameras, scanners, and ink jet printers.

Trademarks Epson is a registered trademark of Seiko Epson Corporation.

PrivateLine and Presenters Club are registered trademarks, and Epson Connection and Epson Store are service marks of Epson America, Inc.

General Notice: Other product names used herein are for identification purposes only and may be trademarks of their respective owners. Epson disclaims any and all rights in those marks.

2004 Epson America, Inc. 4/04

CPD-17928

3

Contents

Welcome . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7 Getting the Most from Your Document Camera . . . . . . . . . . 8 Using Your Documentation . . . . . . . . . . . . . . . . . . . . . . . . . . 8

Getting More Information . . . . . . . . . . . . . . . . . . . . . . . . 9 Registration . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9

1 Setting Up the Document Camera . . . . . . . . . . 11 Unpacking the Document Camera . . . . . . . . . . . . . . . . . . . . 12 Installing Batteries in the Remote Control . . . . . . . . . . . . . . 13 Positioning the Document Camera. . . . . . . . . . . . . . . . . . . . 14 Unfolding the Document Camera . . . . . . . . . . . . . . . . . . . . 15 Connecting to a Projector or TV/Computer Monitor. . . . . . 16

Connecting the RGB Video Cable . . . . . . . . . . . . . . . . . 17 Connecting the RCA Cable . . . . . . . . . . . . . . . . . . . . . . 17 Connecting the S-Video Cable. . . . . . . . . . . . . . . . . . . . 18

Connecting to a Computer. . . . . . . . . . . . . . . . . . . . . . . . . . 18 Connecting a Mouse. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19 Adjusting the Camera DIP Switches . . . . . . . . . . . . . . . . . . . 20

2 Using the Document Camera . . . . . . . . . . . . . . . 21 Turning On Your Equipment. . . . . . . . . . . . . . . . . . . . . . . . 22

Turning On the Document Camera . . . . . . . . . . . . . . . 22 What To Do If You See a Blank Screen . . . . . . . . . . . . . 23

Switching Between Picture Sources. . . . . . . . . . . . . . . . . . . . 24 Adjusting the Lighting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24

Turning the Lamps Off and On. . . . . . . . . . . . . . . . . . . 25

4

Adjusting the Image . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25 Zooming and Focusing Your Image . . . . . . . . . . . . . . . . 26 Doubling the Size of the Image . . . . . . . . . . . . . . . . . . . 27 Adjusting the Brightness . . . . . . . . . . . . . . . . . . . . . . . . 27 Increasing Image Contrast . . . . . . . . . . . . . . . . . . . . . . . 28 Adjusting the White Balance . . . . . . . . . . . . . . . . . . . . . 28 Rotating the Image . . . . . . . . . . . . . . . . . . . . . . . . . . . . 28 Reducing Noise in the Image . . . . . . . . . . . . . . . . . . . . . 28 Switching between Color and Black and White . . . . . . . 29 Freezing the Image. . . . . . . . . . . . . . . . . . . . . . . . . . . . . 29

Using the Pointer . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 30 Adjusting Settings with the On-Screen Display . . . . . . . . . . 30 Projecting Transparencies . . . . . . . . . . . . . . . . . . . . . . . . . . . 33 Saving Settings and Images. . . . . . . . . . . . . . . . . . . . . . . . . . 34

Saving and Recalling Camera Settings . . . . . . . . . . . . . . 34 Saving and Recalling Images . . . . . . . . . . . . . . . . . . . . . 34

Using the Camera Head as a Conventional Video Camera . . . . . . . . . . . . . . . . . . . . 35

Using the Image Mate Software . . . . . . . . . . . . . . . . . . . . . . 35 Installing the Software . . . . . . . . . . . . . . . . . . . . . . . . . . 35 Viewing the On-Screen Manual. . . . . . . . . . . . . . . . . . . 36

Turning Off and Storing the Document Camera . . . . . . . . . 37

3 Maintaining and Transporting the Document Camera . . . . . . . . . . . . . . . . . . . . . . . . . . 39 Cleaning the Lenses . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 40 Cleaning the Document Camera Case . . . . . . . . . . . . . . . . . 41 Transporting the Document Camera . . . . . . . . . . . . . . . . . . 42

5

4 Solving Problems . . . . . . . . . . . . . . . . . . . . . . . . . . . . 43 Solving Problems with the Image . . . . . . . . . . . . . . . . . . . . . 44 Solving Problems with the Remote Control . . . . . . . . . . . . . 47 Where To Get Help . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 48

Telephone Support Services . . . . . . . . . . . . . . . . . . . . . . 48

5 Technical Specifications . . . . . . . . . . . . . . . . . . . . . 49 General . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 49 Lamps. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 50 Remote Control . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 50 Dimensions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 50 Electrical. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 50 Environmental . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 50 Safety . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 51 Compatible Video Formats. . . . . . . . . . . . . . . . . . . . . . . . . . 51

6 Notices . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 53 Important Safety Instructions . . . . . . . . . . . . . . . . . . . . . . . . 53 Remote Control Information . . . . . . . . . . . . . . . . . . . . . . . . 55 Declaration of Conformity . . . . . . . . . . . . . . . . . . . . . . . . . . 57 FCC Compliance Statement. . . . . . . . . . . . . . . . . . . . . . . . . 58 Warranty . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 59

Index . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 61

6

7

Welcome Your versatile Epson ELPDC05 High Resolution Document Camera can be connected to most types of projectors and display devices. From boardrooms to auditoriums to courtrooms, you can show fine detail with a large variety of presentation materials. You can even display three-dimensional objects with perfect illumination and depth of focus.

Your document camera captures images at a resolution of 1024 768 pixels, with a maximum shooting area of 13.7 10.2 inches (350 260 mm). With its 18 zoom capability and true XGA resolution, even 10 point type can be read clearly. For added versatility, the document camera provides built-in white balance for enhancing contrast, gamma selection for projecting in low light environments, and flicker correction for crisper images. Even x-rays display with great clarity.

You can connect the document camera to a wide range of computers, including IBM compatible PCs and laptops, Apple Macintosh, Power Macintosh series (including G3 and G4 systems), PowerBook computers, many iMac and iBook series systems, and high-end workstations such as the Sun SPARCstation.

8 Welcome

Getting the Most from Your Document Camera Depending on your presentation, you can take advantage of any or all of these options:

Connecting to a projector or TV/computer monitor The document camera requires an output device, such as a projector or TV/computer monitor, to display its image. To connect the document camera to these devices, see page 16.

Connecting to a laptop or desktop computer You can connect up to two video output sources, such as laptops or desktop computers. This is especially useful if your projector has only one video input port. See page 18 for more information.

Using the remote control The remote control lets you enlarge or reduce, brighten, focus, and otherwise modify your displayed image. In addition, you can control the lamps, switch the video source from the document camera to a computer, save and recall both images and document camera settings, and pause the display. See Chapter 2 for details.

Using Your Documentation This book contains all the information you need to set up and use your document camera. Please follow these guidelines as you read through it:

Warnings must be followed carefully to avoid bodily injury.

Cautions must be observed to avoid damage to your equipment.

Notes contain important information about your document camera.

Welcome 9

Getting More Information

Need tips on giving presentations or more information about your document camera? Heres where you can look for help:

http://www.presentersonline.com Includes a library of articles covering presentation tips, tricks, and technology. The site provides templates, clip art, and sound clips, as well as Presenters Services to use on the road. Even more resources and services are available if you register to join the Presenters Cluband its free.

http://support.epson.com Download FAQs and e-mail your questions to Epson support.

If you still need help after checking this Users Guide and the sources listed above, you can use the Epson PrivateLine Support service to get help fast. Call (800) 637-7661 and enter the PIN on the card included with your document camera. Or take advantage of Epsons electronic support services 24 hours a day. See page 48 for more information.

Registration To register, simply fill out and return the enclosed registration card, or register online at www.epson.com/webreg. Registering allows Epson to better understand and meet your needs. If you want, you can also receive special updates on new accessories, products, and services.

10 Welcome

11

Setting Up the Document Camera This chapter explains how to set up the document camera for a video presentation. Youll find instructions for:

Unpacking the document camera

Installing batteries in the remote control

Positioning the document camera

Unfolding the document camera

Connecting to a projector or TV/computer monitor

Connecting to a computer

Connecting a mouse to the document camera

Adjusting the document cameras DIP switches

12 Setting Up the Document Camera

Unpacking the Document Camera After unpacking the document camera, make sure you have all the items shown below:

Save all the packaging in case you need to ship the document camera later. Always use the original packaging (or equivalent) when you need to send the document camera to another location. For transportation instructions, see page 42.

Document camera

Remote control

Batteries

RCA cable USB cable RGB video cable

Power cord

Epson Utility Software CD-ROM

Mouse

S-video cable

Setting Up the Document Camera 13

Installing Batteries in the Remote Control Before using the remote control, install its batteries.

1. Press down on the battery cover and slide it off.

2. Insert two AAA batteries as shown.

3. Replace the battery compartment cover.

caution When replacing batteries, take the following precautions:

Dont mix old and new batteries.

Replace batteries as soon as they run out. If the batteries leak, wipe away battery fluid with a soft cloth. If fluid gets on your hands, wash them immediately.

Dont expose batteries to heat or flame.

Dispose of used batteries according to local regulations.

Remove batteries if you wont be using the document camera for a long period of time.

14 Setting Up the Document Camera

Positioning the Document Camera Before connecting the document camera, you need to decide where to place it. Follow these guidelines:

Place the document camera on a sturdy, level surface.

Make sure there is plenty of space for ventilation around and under the document camera.

Make sure the document camera is within 10 feet (3 m) of a grounded electrical outlet or extension cord, and within 5 feet (1.5 m) of your output source.

Make sure you are within 23 feet (7 m) of the document camera to use the remote control.

With the control panel facing you, place the document camera directly in front of you. Otherwise, items you place on the stage may appear upside-down.

Most presenters find it convenient to place the document camera in front of the audience. This lets the presenter stand in the front of the room, face the audience, and remain close enough to the equipment to be able to control it.

caution Dont hold or lift the document camera by the camera head arm or lighting unit arms; this may damage them.

Setting Up the Document Camera 15

Unfolding the Document Camera Follow these steps to unfold the document camera:

1. Raise the arm for the left lighting unit until it stops. Then raise the right lighting unit.

2. Position the lighting units so that they face the stage (downward).

3. Press the camera arm release button as you raise the camera arm. When the camera arm stops, release the button to lock the arm into place.

Camera arm release button

16 Setting Up the Document Camera

4. Rotate the camera head so that the lens faces the stage (downward).

Connecting to a Projector or TV/Computer Monitor You can connect the document camera to any projector or monitor that has a standard RGB video, composite video, or S-video input port. Epson projectors support these connections. Most computer monitors support only RGB video, while many television monitors support composite video. Follow the instructions below to connect the document camera to your display device.

Setting Up the Document Camera 17

Connecting the RGB Video Cable

Before you start, make sure your document camera and projector or computer monitor are turned off.

1. Connect one end of the RGB video cable to the document cameras RGB OUT port.

2. Connect the other end to the RGB video input port on the projector or computer monitor.

3. Tighten the screws on the connectors.

Connecting the RCA Cable

Before you start, make sure your document camera and projector or TV are turned off.

1. Connect one end of the RCA cable to the document cameras VIDEO OUTPUT port.

2. Connect the other end to the RCA input port on the projector or TV.

note The RGB video input port on the projector or monitor may be labeled computer, or video in.

or

Projector

Monitor

RGB OUT port

or

Projector

TVVIDEO OUTPUT port

18 Setting Up the Document Camera

Connecting the S-Video Cable

Before you start, make sure your document camera and projector or TV are turned off.

1. Connect one end of the S-video cable to the document cameras S-VIDEO OUTPUT port.

2. Connect the other end to the S-video input port on the projector or TV.

Connecting to a Computer The document camera comes with two RGB video input ports. These can be used to connect up to two laptops or desktop computers to the document camera.

This is especially useful if your projector has only one input port. You can connect one or two computers to the document cameras RGB input port(s) as described below, and connect the document camera to the projectors input port as described on page 16. This way, you can use the cameras remote control to switch between picture sources. Follow the instructions on page 24 to switch between the sources.

or

Projector

TVS-VIDEO OUTPUT port

note For best image quality when projecting a computer image, connect your projector or monitor to the document camera using the RGB OUT port.

Setting Up the Document Camera 19

Before you start, make sure your document camera and computer(s) are turned off.

1. Connect one end of the RGB video cable to the RGB1 INPUT port on the document camera.

2. Connect the other end of the RGB video cable to your computers RGB video output (monitor) port.

3. Tighten the screws on the connectors.

4. To connect a second computer, repeat the preceding steps, except connect the RGB video cable to the RGB2 INPUT port on the document camera.

Connecting a Mouse The mouse included with your document camera functions as a pointing device. It also gives you access to the document cameras on-screen display, which controls many of the features that are selectable from the remote control. (See page 30 for details about using the on-screen display.)

1. Make sure your document camera is turned off.

2. Connect the mouse cable to the MOUSE port on the back of the document camera.

Computer

Laptop

RGB input ports

MOUSE port

20 Setting Up the Document Camera

Adjusting the Camera DIP Switches The document camera has two DIP switches that control special settings. Refer to the table below to make sure they are set correctly for your configuration.

* Default setting

DIP Switch 0 1 Function

A NTSC* PAL Selects the TV video output format. Select NTSC for US model TV sets and PAL for European TV sets.

B Overscan Underscan* Selects how much of the document stage is projected. When overscan is selected, slightly more area is projected since the document cameras effective pixels, 1034 779, are utilized.

DIP switches

note Make sure the document camera is turned off before you change the DIP switch settings.

21

Using the Document Camera Once you have set up the document camera, youre ready to turn it on, adjust the image, and give your presentation. This chapter covers the following:

Turning on the document camera and other equipment

Switching between picture sources

Adjusting the lighting

Adjusting the image

Using the pointer

Adjusting settings with the on-screen display

Projecting film and slides

Saving settings and images

Using the camera head as a conventional video camera

Using the Image Mate software

Turning off and storing the document camera

22 Using the Document Camera

Turning On Your Equipment Make sure your document camera and other equipment are set up and connected correctly, as described in Chapter 1. Always turn on your projector or monitor first. Then turn on your document camera, as described below, followed by any other equipment youve connected to it.

If you have one or two computers connected to the document cameras RGB INPUT ports, you may have to switch between sources to see the desired image. See page 24 for details.

Turning On the Document Camera

Follow these steps to plug in and turn on the document camera:

1. Connect one end of the power cord to the document cameras power inlet.

2. Connect the other end to a grounded electrical outlet.

3. Turn on the projector or monitor.

4. Turn on the document camera. After a moment, the upper lamps turn on.

Power inlet

On/Off switch

Using the Document Camera 23

5. Place your presentation material on the stage. You should see an image on screen.

Once you see your image, turn to page 25 for instructions on making adjustments.

If your image doesnt appear, see the next section for help.

When youre done with your presentation, turn off the document camera as described on page 37.

What To Do If You See a Blank Screen

If an image doesnt appear, try the following:

Make sure the cables are connected correctly, as described in Chapter 1.

Make sure everything is turned on.

If you are using a video source, such as a laptop or desktop computer, you may need to switch video sources. Press the RGB1 or RGB2 buttons as described on page 24.

If an image still doesnt appear, refer to Chapter 4 for more help.

note If you turn off the document camera, always wait a few seconds before turning it back on.

24 Using the Document Camera

Switching Between Picture Sources If you have an external video source connected to the document camera, such as a laptop or desktop computer, you can switch between the video source and the camera.

If youve connected a computer to the RGB1 INPUT port on the document camera, press the RGB1 button on the remote control.

If youve connected another computer to the RGB2 INPUT port, press the RGB2 button to access that source.

Press the Main button to switch back to the document camera.

Adjusting the Lighting If you are presenting printed material or three-dimensional objects, the two upper lamps provide ample light. If the ambient lighting in the room is sufficient, however, you may obtain a better image with the upper lamps off.

In addition, you may want to turn the upper lamps off and the base lamp on if youre projecting film or slides.

note You can also press the RGB1, RGB2, and MAIN buttons on the document camera to switch to a different video source.

PAUSE

LAMPPOSI/NEGA COLOR/B&W

IRIS

AF

2x

SET

RGB1 RGB2

NORMAL OPEN CLOSE

PRESETCALL

TELE ZOOM

MAIN INPUT

WIDE NEAR FOCUS FAR

UPPER BASE

SET IMAGE CALL

Select the image source

Using the Document Camera 25

Turning the Lamps Off and On

Press the UPPER LAMP button on the remote control to turn off the lamps. Press it again when you want to turn the lamps back on. There will be a slight delay before the lamps turn back on.

Press the BASE LAMP button on the remote control to turn the base lamp on. Press it again to turn the base lamp off.

Adjusting the Image Once you see your image, you may need to make certain adjustments:

To zoom or focus the image, see the next section

To double the size of the projected image, see page 27

If the image is too light or dark, see page 27

To increase the contrast between the image and its background, see page 28

If the image has a color cast, see page 28

To rotate the image, see page 28

To reduce noise in the image, see page 28

To switch to a black and white image, see page 29

To freeze the image, see page 29

note You can also press the LAMP button on the document camera to move through this sequence: upper lamps off and base lamp on, upper and base lamps off, upper lamps on and base lamp off.PAUSE

LAMPPOSI/NEGA COLOR/B&W

IRIS

AF

2x

SET

RGB1 RGB2

NORMAL OPEN CLOSE

PRESETCALL

TELE ZOOM

MAIN INPUT

WIDE NEAR FOCUS FAR

UPPER BASE

SET IMAGE CALL

Turn the lamps on and off

26 Using the Document Camera

Zooming and Focusing Your Image

Use the Tele button on the document camera or remote control to enlarge the image, and use the Wide button to reduce it. The document camera will automatically focus the image.

If you change items on the stage, press the AF button on the remote control or the AUTO FOCUS button on the document camera to focus the image. The indicator light on the document camera flashes until the image is focused.

The following objects may not focus well using the auto focus feature:

Objects with little contrast

Objects with a bright background or excessive contrast

Objects with fine repeated patterns or stripes

Objects that glitter or reflect bright light

Objects with varying depths of field

To manually focus these objects, use the NEAR or FAR button on the remote control. Additionally, use these buttons if you want to focus on a particular part of a three-dimensional object on the stage.

note The auto focus function works up to a height of approximately 3.9 in. (10 cm) above the stage surface.

PAUSE

LAMPPOSI/NEGA COLOR/B&W

IRIS

AF

2x

SET

RGB1 RGB2

NORMAL OPEN CLOSE

PRESETCALL

TELE ZOOM

MAIN INPUT

WIDE NEAR FOCUS FAR

UPPER BASE

SET IMAGE CALL

Automatically focuses the image

Enlarge or reduce the image

Manually focus the image

INPUT PAUSE

CLEAR MODE

MAIN

RGB1

RGB2

IRIS

ZOOM

OPEN CLOSE

TELE WIDE AUTO FOCUS

AUTO/MANUAL

CONTRAST POSI / NEGA

LAMP WHITE BALANCE

IMAGE ROTATION

UPPER / BASE / OFF

Automatically focuses the imageEnlarge or reduce the image

Using the Document Camera 27

Doubling the Size of the Image

You can instantly double the size of the displayed image by pressing the 2x button on the remote control, or pressing the right mouse button if a mouse is attached to the document cameras MOUSE port (see page 19). To return the image to its original size, press the 2x button or the right mouse button again.

Adjusting the Brightness

The document camera is initially set to auto iris. You can manually adjust the iris to control the amount of light that reaches the camera.

If the screen looks dark, press and hold the OPEN button on the remote control to open the iris so that more light reaches the camera. If the screen looks too bright, press and hold the CLOSE button. To return to the auto iris default setting, press the NORMAL button.

To lock the brightness setting, press the AUTO/MANUAL button on the document camera. The buttons indicator light comes on when the camera is locked in manual mode. You can then use the OPEN and CLOSE buttons to adjust the brightness. Press the AUTO/MANUAL button again to unlock manual mode. (The NORMAL button on the remote control has no effect while manual mode is locked.)

PAUSE

LAMPPOSI/NEGA COLOR/B&W

IRIS

AF

2x

SET

RGB1 RGB2

NORMAL OPEN CLOSE

PRESETCALL

TELE ZOOM

MAIN INPUT

WIDE NEAR FOCUS FAR

UPPER BASE

SET IMAGE CALL

Doubles the size of the image

Adjust brightness

INPUT PAUSE

CLEAR MODE

MAIN

RGB1

RGB2

IRIS

ZOOM

OPEN CLOSE

TELE WIDE AUTO FOCUS

AUTO/MANUAL

CONTRAST POSI / NEGA

LAMP WHITE BALANCE

IMAGE ROTATION

UPPER / BASE / OFF

Locks and unlocks the brightness setting

Adjust brightness when setting is locked

28 Using the Document Camera

Increasing Image Contrast

Some images display best when the contrast between the image and its background is increased. To increase contrast, press the CONTRAST button on the document camera. To turn contrast off, press the button again.

Adjusting the White Balance

Normally, the document camera automatically adjusts the screens white balance. However, it may be necessary to correct for color shifts in different lighting conditions.

If the displayed image has a color cast, press the WHITE BALANCE button on the document camera once to correct the color shift. If you later want to return to automatic white balance adjustment, press the button a second time. (See page 30 for manual white balance adjustments using the document cameras on-screen display.)

Rotating the Image

You can rotate the image by 90 in a counterclockwise direction each time you press the IMAGE ROTATION button on the document camera. For instructions on rotating the image using the on-screen display, see page 30.

Reducing Noise in the Image

To reduce noise in the projected image, press the CLEAR MODE button on the document camera. To exit this mode, press the button again.

INPUT PAUSE

CLEAR MODE

MAIN

RGB1

RGB2

IRIS

ZOOM

OPEN CLOSE

TELE WIDE AUTO FOCUS

AUTO/MANUAL

CONTRAST POSI / NEGA

LAMP WHITE BALANCE

IMAGE ROTATION

UPPER / BASE / OFF

Increases or decreases contrast

Rotates the image 90

Corrects color shifts

Reduces noise in the image

Using the Document Camera 29

Switching between Color and Black and White

Sometimes you may want to switch to a black and white image. For example, a black and white display allows you to project text without color interference, resulting in a sharper image.

To switch from color to black and white, press the COLOR/B&W button on the remote control. Press it again when you want to switch back to color.

Freezing the Image

During a presentation, it may be necessary to change the material you are displaying. Press the PAUSE button before switching your material. This freezes the image on screen, allowing you to change your material. When you are ready to display the next item, press the Pause button again.

PAUSE

LAMPPOSI/NEGA COLOR/B&W

IRIS

AF

2x

SET

RGB1 RGB2

NORMAL OPEN CLOSE

PRESETCALL

TELE ZOOM

MAIN INPUT

WIDE NEAR FOCUS FAR

UPPER BASE

SET IMAGE CALL

Switches between color and black and white display

note The pause feature only works when the document camera is in the MAIN display mode. It does not work when the document camera is in the RGB1 or RGB2 display modes.

PAUSE

LAMPPOSI/NEGA COLOR/B&W

IRIS

AF

2x

SET

RGB1 RGB2

NORMAL OPEN CLOSE

PRESETCALL

TELE ZOOM

MAIN INPUT

WIDE NEAR FOCUS FAR

UPPER BASE

SET IMAGE CALL

Freezes the image

30 Using the Document Camera

Using the Pointer The pointer lets you direct attention to specific sections of your presentation material. You can choose from two types of pointers in four colors.

To display the pointer, connect the mouse that came with the document camera to the MOUSE port (see page 19) and press either the left mouse button or the center wheel.

The mouse allows you to move the pointer as you would on a computer. You can also do the following:

With the pointer displayed, click either the left mouse button or the center wheel to see the on-screen display menu. Click again to clear the menu. Click a third time to clear the pointer.

Click items on the on-screen display menu to activate them.

Click the right mouse button to double the size of the displayed image.

For information on selecting different types of pointers, see page 31.

Adjusting Settings with the On-Screen Display The on-screen display allows access to many of the settings available with the document cameras remote control. To access the on-screen display, you must have the mouse connected to the document cameras MOUSE port (page 19). When you click either the left mouse button or the center wheel, the on-screen display menu and pointer appear (you may have to click twice).

Center wheel

Left mouse button

Right mouse button

note The pointer feature only works when the document camera is in the MAIN display mode. It does not work when the document camera is in the RGB1 or RGB2 display modes.

Using the Document Camera 31

The table below lists the various functions and their descriptions. To select an item, point and click the left mouse button or center wheel.

Icon Name Function

Upper Lamps On/Off

Turns the upper lamps on and off. (It may take a few seconds for the lamps to come on again.)

Base Lamp ON/OFF

Turns the base lamp on and off. (The first time you click the icon, it turns the base lamp on and the upper lamps off.)

Color/B&W Switches the display from color to black and white.

Pause On/Off

Freeze and unfreeze the displayed image.

Auto Focus Automatically brings objects on the stage into focus.

Zoom Tele/Wide

Enlarge and reduce the displayed image.

Focus Near/Far

Manually focus objects that cannot be focused automatically.

Iris Open/Close

Increase and reduce image brightness.

Pointer Changes the shape and color of the on-screen pointer.

32 Using the Document Camera

White Balance Displays the white balance adjustment menu.

White Balance Automatic

Automatically adjusts the white balance and corrects color casts.

White Balance One Touch

Click once to correct color shift for the current lighting environment.

White Balance Manual

Enables manual white balance adjustment. Click the arrows below to adjust the colors individually to compensate for color casts.

Image Rotation Rotates the image 90 in a counterclockwise direction each time it is clicked.

Positive/Negative Film Display

Switches between screen settings (gamma, white balance, and contrast) designed to display positive film, and settings designed for negative film.

Aperture Selection On/Off

Turn image enhancement (contour) on and off. This setting is on by default.

Gamma Selection

Changes the gamma setting. The default gamma setting is 0.6.

Save Settings Saves changes made to the document camera settings.

Restore Defaults

Restores settings to factory defaults.

Icon Name Function

Using the Document Camera 33

Projecting Transparencies The document camera enables you to project both positive and negative film with great clarity. Follow these steps:

1. Place your film or slides on the document cameras stage with the dull side facing up.

2. Do one of the following to turn the upper lamps off and the base lamp on:

Press the UPPER LAMP button on the remote control, and then the BASE LAMP button.

Press the LAMP button on the document camera.

3. If youre projecting negative film, press the POSI/NEGA button on either the remote control or document camera.

If you want to continue normal projection when youre done, turn the base lamp off and the upper lamps on again. If you were projecting negative film, press the POSI/NEGA button again to return to normal display.

PAUSE

LAMPPOSI/NEGA COLOR/B&W

IRIS

AF

2x

SET

RGB1 RGB2

NORMAL OPEN CLOSE

PRESETCALL

TELE ZOOM

MAIN INPUT

WIDE NEAR FOCUS FAR

UPPER BASE

SET IMAGE CALL

Switches between normal projection and negative film projection

Turn upper lamps off and base lamp on

note It may take a few seconds for the base lamp to come on.INPUT PAUSE

CLEAR MODE

MAIN

RGB1

RGB2

IRIS

ZOOM

OPEN CLOSE

TELE WIDE AUTO FOCUS

AUTO/MANUAL

CONTRAST POSI / NEGA

LAMP WHITE BALANCE

IMAGE ROTATION

UPPER / BASE / OFF

Turns the lamps on and off

Switches between normal projection and negative film projection

34 Using the Document Camera

Saving Settings and Images You can save up to eight groups of document camera settings for later use. That way, if you want to present the same type of materials (for example, negative film), you can quickly recall your settings with a simple push of a button.

You can also recall up to eight individual images captured by the document camera.

Saving and Recalling Camera Settings

To save your settings, press the PRESET SET button on the remote control, then press one of the numbered buttons between 1 and 8. The message PRESET x WRITE appears on the screen (where x is the number assigned to the group).

To recall a group of saved settings, press the PRESET CALL button on the remote control, then press the number of the group you want to use. The message MOVE x appears (where x is the number of the group) and the appearance of the screen changes to show your settings.

Saving and Recalling Images

To save a copy of the projected image, press IMAGE SET on the remote control, then press one of the numbered buttons between 1 and 8. The message MEMORY STATUS appears, followed by IMAGE x WRITE, where x is the number assigned to the image.

To recall a saved image, press IMAGE CALL on the remote control, then the number of the image you want to display. The saved image appears on the screen.

note Camera settings remain in memory even when you turn the document camera off. However, saved images are deleted when the camera is turned off.

PAUSE

LAMPPOSI/NEGA COLOR/B&W

IRIS

AF

2x

SET

RGB1 RGB2

NORMAL OPEN CLOSE

PRESETCALL

TELE ZOOM

MAIN INPUT

WIDE NEAR FOCUS FAR

UPPER BASE

SET IMAGE CALL

Press to save and recall images

Press to save and recall settings

Assign a number to saved settings and images

Using the Document Camera 35

Using the Camera Head as a Conventional Video Camera By rotating the camera head to a horizontal position, you can use the document camera as a conventional video camera. To view walls or distant objects, flip down the close-up lens. The document camera can resolve images from 1.6 feet (0.5 m) to infinity.

Using the Image Mate Software The Image Mate software allows you to transfer images from the document camera to a computer running Windows. You can also use the virtual remote control feature to control the document camera and change its settings.

Installing the Software

Follow these steps to install the Image Mate software:

1. Insert the Epson Utility Software CD-ROM in your drive.

2. Open the CD-ROM window.

For Windows XP, click Start > All Programs > My Computer, then double-click the CD-ROM icon.

For other Windows systems, double-click My Computer on your desktop, then double-click the CD-ROM icon.

3. Double-click Setup-exe and follow the on-screen instructions.

note The cameras shutter operates at 20 frames per second.

Close-up lens

Camera head in horizontal position

note To use the Image Mate software, connect the document camera to your Windows computer with the USB cable that came with the camera.

36 Using the Document Camera

4. When you see the license agreement, click Agree, then Next to continue.

5. When installation is complete, click Finish.

Viewing the On-Screen Manual

To view the on-screen manual, do the following:

1. Insert the Epson Utility Software CD-ROM in your drive.

2. Open the CD-ROM window.

3. If you have Adobe Acrobat Reader installed on your computer, go to step 6.

If you dont have Adobe Acrobat Reader installed, double-click the Acrobat folder.

4. Double-click the US folder, then double-click ar500enu.exe. Acrobat Reader installs on your computer.

5. Close the US folder, then close the Acrobat folder.

6. Double-click the US folder. Then double-click manual.pdf.

The manual opens on your desktop. Use the arrows at the top of the screen to navigate the manual, or click the Bookmarks tab to see a list of topics, then click the topic you want to view.

Click to view a list of topics Or use the arrows to navigate

Using the Document Camera 37

Turning Off and Storing the Document Camera When youve finished using the document camera, follow these steps to turn off and store it. If youre using a monitor or projector, shut it down last.

1. Turn off the document camera.

2. Unplug the power cord and disconnect any attached video cables.

3. If the close-up lens is flipped down, close it.

4. Place the remote control inside the remote control storage compartment and close the tray.

Place the remote control in its storage compartment

Turn off the camera

38 Using the Document Camera

5. Rotate the camera head to its storage position.

6. Press the camera arm release button as you carefully lower the camera arm onto the stage.

7. Lower the arm for the right lighting unit, and then lower the arm for the left lighting unit.

s

Camera arm release button

39

Maintaining and Transporting the Document Camera Your document camera needs little maintenance. All you need to do on a regular basis is keep the lenses and stage clean. Any dirt or smears on the lenses or stage may show up on your displayed image.

You should not replace the lamps or any other parts. If any part needs replacing, contact your dealer or a qualified servicer.

This chapter covers the following:

Cleaning the lenses

Cleaning the document camera case

Transporting the document camera

warning Before you clean any part of the document camera, turn it off and unplug the power cord. Never open any cover on the document camera. Dangerous electrical voltages in the document camera can injure you severely. Dont try to service this product yourself. Refer all servicing to qualified service personnel.

40 Maintaining and Transporting the Document Camera

Cleaning the Lenses Clean the lenses whenever you notice dirt or dust on the surface.

Use a canister of compressed air to remove dust.

To remove dirt or smears on the lenses, use lens-cleaning paper. If necessary, moisten a soft cloth with lens cleaner and gently wipe the lens surface.

Clean both sides of the close-up lens.

Close-up lens

Main lens

Maintaining and Transporting the Document Camera 41

Cleaning the Document Camera Case Before you clean the case, first turn off the document camera and unplug the power cord.

To remove dirt or dust, wipe the case with a soft, dry, lint-free cloth.

To remove stubborn dirt or stains, moisten a soft cloth with water and a neutral detergent. Then wipe the case.

Do not use wax, alcohol, benzene, thinner, or other chemical detergents. These can damage the case.

Take special care when cleaning the stage, or you may scratch it. Scratches on the stage may appear on your image.

Stage

42 Maintaining and Transporting the Document Camera

Transporting the Document Camera The document camera contains many glass and precision parts. If you need to transport it, follow these guidelines to prevent damage to the document camera:

Make sure to turn off and fold the document camera as described on page 37.

When shipping the document camera for repairs, use the original packaging material if possible. If you do not have the original packaging, use equivalent materials, placing plenty of cushioning around the document camera.

When transporting the document camera a long distance, pack it in a sturdy box, using cushioning around the document camera.

When hand-carrying the document camera, use the carrying handle.

When transporting the document camera, leave the remote control inside the remote control storage compartment.

note Epson shall not be liable for any damages incurred during transportation.

Remote control storage compartment

Carrying handle

43

Solving Problems This chapter helps you solve problems with your document camera, and tells you how to contact technical support for problems you cant solve yourself. This chapter explains the following:

Solving problems with the image

Solving problems with the remote control

Contacting technical support

44 Solving Problems

Solving Problems with the Image

No image appears on the screen.

Check that all cables are properly connected (see Chapter 1) and everything is turned on.

Make sure the power switch is turned on.

Make sure the projector or computer is not in sleep mode. Check the projector documentation, or try pressing a key on the computer keyboard.

The document camera may have been turned on too quickly after it was turned off. Turn the document camera off, wait a few seconds, and then turn it on again.

The wrong source may be selected. Try pressing the Main, RGB1, or RGB2 button on the remote control or document camera.

You may need to change the NTSC or PAL DIP switch setting on the document camera. See page 20 for instructions.

The image contains static or noise.

If youre using cables that are longer than 6 feet (2 m), or an extension cable, the image quality may be reduced. Try using the cables supplied with the document camera. If longer cables are required, consider using a distribution amplifier such as the one available from Epson (ELPDA01).

Keep your projector, computer, and video cables away from the power cord as much as possible to prevent interference.

The cameras DIP switches may be set incorrectly. Try adjusting the switches as described on page 20.

Try pressing the CLEAR MODE button on the document camera, especially if youre taking pictures of three-dimensional objects.

If you notice a decline in the projected image quality when the image is displayed simultaneously on your laptop computer and projector, turn off the laptops LCD display.

note To order accessories from Epson, call (800) 873-7766, or visit the Epson Store at www.epsonstore.com (U.S. sales only). In Canada, call (800) 463-7766 for dealer referral.

SM

Solving Problems 45

For best image quality when projecting a computer image, connect your projector or monitor to the document cameras RGB OUT port.

The image is blurry.

There may be dirt on the lenses. Clean the lenses as described on page 40.

Try pressing the AF (Auto Focus) button on the remote control, or the AUTO FOCUS button on the document camera.

Some objects do not focus well automatically (see page 26). Manually focus these objects using the Near and Far buttons.

The presentation material may be too close to the lens. Make sure the close-up lens is closed.

The presentation material may be too far from the lens. Open the lens by flipping it down.

Make sure there is no condensation on the lenses. You may need to wait before using the document camera after moving it from a cold environment to a warm environment.

The image is too dark.

Make sure the document cameras upper lamps are on. Press the UPPER LAMP button on the remote control, if necessary.

Press the IRIS OPEN button on the remote control or document camera to open the iris on the camera lens.

If youre displaying the image on a TV or computer monitor, adjust the monitor brightness controls.

Use the on-screen display to adjust the gamma setting (see page 32).

The colors dont look right.

Try adjusting the white balance (see page 28).

If youre projecting an image from a computer, check your computers display settings to correct the color balance.

note You can also press the LAMP button on the document camera to move through this sequence: upper lamps off and base lamp on, upper and base lamps off, upper lamps on and base lamp off.

46 Solving Problems

The image is garbled.

Make sure your computer and/or projector or monitor are securely connected at both ends to the document camera.

Check the DIP switches on the document camera. If video output is set to NTSC and the document camera is connected to a monitor that supports PAL, the image may appear garbled. See page 20 for instructions on adjusting the DIP switches.

A color image displays in black and white.

Try pressing the COLOR/B&W button on the remote control to switch to color mode.

Check the DIP switches on the document camera. If video output is set to NTSC and the document camera is connected to a monitor that supports PAL, the image may display in black and white. See page 20 for instructions on adjusting the DIP switches.

Solving Problems 47

Solving Problems with the Remote Control Make sure you are within 23 feet (7 m) of the document camera,

and within range of the document cameras sensor (approximately 30 to the left or right and 15 above or below).

The remote control batteries may not be installed correctly or may be low on power. Try changing the batteries as described on page 13.

Dim the room lights and turn off any fluorescent lighting. Make sure the document camera is not in direct sunlight. Strong lighting, especially fluorescent lights, may affect the document cameras infrared receivers.

Turn off any nearby equipment that emits infrared energy, such as a radiant room heater.

If the NORMAL button on the remote control does not return the screen to the auto iris default setting, try pressing the AUTO/MANUAL button on the document camera. When this buttons indicator light is on, the document camera is locked in manual mode and the remote controls NORMAL button has no effect.

48 Solving Problems

Where To Get Help Epson provides technical assistance through electronic support services 24 hours a day, as listed in the following table:

Telephone Support Services

To use the Epson PrivateLine Support service, call (800) 637-7661 and enter the PIN on the Epson PrivateLine Support card included with your document camera. This is the fastest way to speak to a live representative, and its free. This service is available 6 AM to 6 PM, Pacific Time, Monday through Friday, for the duration of your warranty period.

You may also speak with an Epson document camera support specialist by dialing one of these numbers:

U.S.: (562) 276-4394, 6 AM to 6 PM, Pacific Time, Monday through Friday

Canada: (905) 709-3839, 6 AM to 6 PM, Pacific Time, Monday through Friday

Toll or long distance charges may apply.

Before you call, please have the following information ready:

Product name (Epson ELPDC05 High Resolution Document Camera)

Product serial number (located on the rear panel of the document camera)

Computer configuration, if applicable

Description of the problem

Service Access

World Wide Web From the Internet, you can reach Epsons product support at http://support.epson.com. After selecting your product, you can access troubleshooting information, download product documentation, and receive technical advice through e-mail.

Presenters Online Access tips, templates, and training for developing successful presentations at http://www.presentersonline.com.

49

Technical Specifications General

CCD 1/3 inch (848,676 progressive scan)

Resolution 1024 768 pixels (Effective resolution, or overscan, is 1034 779 pixels)

Lens F=2.8, f=4.7 to 84.6 mm

Frame speed 20 frames per second

Shooting area 13.7 10.2 in. (350 260 mm) max. 1.0 0.8 in. (25 19 mm) min.

Limit of focus adjustment 3.9 in. (100 mm) from the stage surface

using the close-up lens 1.6 feet (0.5 m) to infinity with the camera positioned horizontally and without using the close-up lens

Zoom 18 optical with double speed function

Focus Automatic/manual

Iris Automatic/manual

White balance Automatic/manual

Gamma selection ON (=0.3/0.4/0.5/0.6/0.7/0.8/0.9) OFF (=1.0)

Image rotation 90/180/270

Frequency selection 50 or 60 Hz

Video output NTSC or PAL

50 Technical Specifications

Lamps

Upper High frequency fluorescent, 6 W 2

Base High frequency fluorescent

Remote Control

Range 23 feet (7 m)

Angle from IR receiver Approx. 30 to the right or left, and 15 up

or down

Batteries Alkaline AAA (2)

Dimensions

Weight 21.6 lb (9.8 kg)

Folded (h w d) 7.1 15.7 21.3 in. (181 400 542 mm)

Unfolded (h w d) 21.9 27.4 21.3 in. (555 697 542 mm)

Electrical

Rated frequency 50/60 Hz

Power supply 100 to 240 VAC

Power consumption 100 to 240 VAC; 55 W

Rated current 0.8 A to 0.4 A

Environmental

Temperature Operating: 41 to 104 F (5 to 40 C) Storage: 14 to 140 F (10 to 60 C)

Humidity Operating: 30 to 85% RH, non-condensing

Storage: 20 to 90% RH, non-condensing

Technical Specifications 51

Safety

United States FCC 47CFR Part 15B Class B (DoC) UL1950 3rd Edition

Canada ICES-003 Class B CSA C22.2 No.950-95 (cUL)

Compatible Video Formats

The document camera supports NTSC and PAL video standards, as well as the monitor display formats listed below.

Mode Refresh Rate (Hz) Resolution

VGA1 84.889 640 350

VGA2 85.08 640 400

VGA3 85.039 720 400

VGA60 59.94 640 480

VGA72 72.809 640 480

VGA75 75 640 480

VGA85 85.008 640 480

SVGA56 56.25 800 600

SVGA60 60.317 800 600

SVGA72 72.188 800 600

SVGA75 75 800 600

SVGA85 85.061 800 600

XGA60 60.004 1024 768

XGA70 70.069 1024 768

XGA75 75.029 1024 768

XGA85 84.997 1024 768

SXGA1 75 1152 864

SXGA2 60 1280 960

SXGA3 85.003 1280 960

SXGA60 60.02 1280 1024

52 Technical Specifications

SXGA75 75.025 1280 1024

SXGA85 85.024 1280 1024

UXGA60 60 1600 1200

UXGA65 65 1600 1200

UXGA70 70 1600 1200

UXGA75 75 1600 1200

UXGA85 85 1600 1200

MAC 13 66.667 640 480

MAC 16 74.55 832 624

MAC 19 74.927 1024 768

MAC 21 75.062 1152 870

PC98 56.42 640 400

Mode Refresh Rate (Hz) Resolution

53

Notices This chapter includes safety instructions and other important information about your Epson document camera.

Important Safety Instructions Follow these safety instructions when setting up and using the document camera:

Before setting up the document camera, read all safety and operating instructions. Keep the instructions for future reference.

Be sure to adhere to all warnings in the documentation and on the document camera.

Carefully follow the instructions in this guide to set up and use the document camera.

Turn off and unplug the document camera before cleaning. Clean with a damp cloth only. Never use liquid or aerosol cleaners, or solvents or harsh chemicals like benzene or paint thinner, as these may damage the document camera.

Never point the lens into the sun, as this may damage the document camera.

Use only attachments and accessories recommended by Epson.

Never use the document camera near waterfor example, near a bath tub, kitchen sink, laundry tub, or swimming pool. Avoid humid environments, such as a wet basement.

Do not place the document camera near a radiator or heating vent or in direct sunlight. Avoid placing it near equipment that generates heat.

Avoid locations that are subject to shocks or vibrations, dust, or rapid changes in heat or humidity.

Place the document camera on a flat, stable surface that extends beyond its base in all directions.

54 Notices

Do not block or cover openings in the base, or insert objects through the slots. These openings are provided for ventilation to protect the document camera from overheating. Never place the document camera on a bed, sofa, rug, or similar surface. Do not place the document camera in a built-in installation, such as a bookcase or rack, unless proper ventilation is provided and the guidelines in this manual are followed.

Place the document camera near a wall outlet where the plug can be easily unplugged.

Placez lappareil prs dune prise de courant o la fiche peut tre dbranche facilement.

Use only the type of power source indicated on the document camera label.

Connect the document camera to a properly grounded power outlet. Avoid using outlets on the same circuit as air control systems or other high-load devices that regularly switch on and off.

If you use an extension cord with the document camera, make sure the total ampere rating of the devices plugged into the extension cord does not exceed the cords ampere rating. Also, make sure the total ampere rating of all devices plugged into the wall outlet does not exceed the wall outlets ampere rating. Overloading extension cords, power strips, or wall outlets can result in fire or electric shock.

Follow the instructions in this manual to install batteries in the remote control. Never expose batteries to heat or flame, and never mix old and new batteries or batteries of different types. Do not use rechargeable Ni-Cd batteries, and do not try to recharge or short-circuit the batteries. Replace batteries as soon as they run out. If the batteries leak, wipe away battery fluid with a soft cloth. If fluid gets on your hands, wash them immediately. Dispose of used batteries according to local regulations.

This product may be equipped with either a polarized 2-wire AC line plug (a plug having one blade wider than the other) or a 3-wire grounding type plug (a plug having a third grounding pin). The 2-wire polarized plug will fit into the power outlet only one way. This is a safety feature. If you are unable to insert the plug fully into the outlet, try reversing the plug. If the plug still fails to fit, contact your electrician to replace your obsolete outlet. Do not defeat the safety purpose of the polarized plug. The 3-wire grounding type plug will fit into a grounding type power outlet. This is a safety feature. If you are unable to insert the plug into the outlet, contact your electrician to replace your obsolete outlet. Do not defeat the safety purpose of the grounding type plug.

Notices 55

Do not let the power cord become damaged or frayed. Place the document camera in a location where people are unlikely to walk on the power cord, and the cord is not pinched by items placed upon or against it.

Unplug the document camera and disconnect the cable when not in use, or when there is a lightning storm. This will prevent damage to the product due to power surges and lightning.

Take care when using a cart to move the document camera that the cart doesnt overturn or the document camera fall off.

Refer all servicing to qualified service personnel. Do not attempt to take apart the document camera or open its cabinet, as this may expose you to high voltage or other dangers.

Unplug the document camera and refer servicing to qualified service personnel under the following conditions: if the power cord or plug is damaged; if liquid has entered the product; if the product has been dropped or the case damaged; if the product does not operate normally or exhibits a distinct change in performance. Adjust only those controls that are covered by the instructions in this manual.

This product includes a lamp component that contains mercury (Hg). Please consult your state and local regulations regarding disposal or recycling. Do not put in the trash.

To make sure that only Epson replacement parts are used, refer all servicing to Epson-authorized servicers. Substitution of unauthorized parts may result in fire, electric shock or other hazards.

Upon completion of any service or repairs to this product, ask the service technician to perform safety checks to determine that the product is in proper operating condition.

Handling the cord on this product or cords associated with accessories sold with this product will expose you to lead, a chemical known to the state of California to cause birth defects or other reproductive harm. Wash hands after handling.

Remote Control Information You can operate the document camera by remote control via a line-of-sight infrared (IR) receiver on top of the camera arm. The document camera may not respond to remote control commands under the following conditions:

There is an object between the remote control IR emitter and the IR receiver on the document camera.

Ambient light is too bright.

56 Notices

Certain types of fluorescent lighting are used.

A strong light source shines into the IR receiver.

Other equipment that emits infrared energy, such as a radiant room heater, is in the room.

These conditions commonly cause problems for most infrared-controlled equipment. Try the following if you experience problems:

The remote control batteries may be low on power; replace them.

Dim the ambient lighting and/or turn off any fluorescent lights.

Close any window coverings and/or move the document camera out of direct sunlight.

Turn off other equipment that emits infrared energy.

If the remote control still does not work properly, you can always use the buttons located on the document camera control panel, even in an environment containing one of the conditions listed above.

Notices 57

Declaration of Conformity According to 47CFR, Part 2 and 15 Class B Personal Computers and Peripherals; and/or CPU Boards and Power Supplies used with Class B Personal Computers

We: Epson America, Inc. Located at: 3840 Kilroy Airport Way

MS: 3-13 Long Beach, CA 90806

Telephone: (562) 290-5254

Declare under sole responsibility that the product identified herein, complies with 47CFR Part 2 and 15 of the FCC rules as a Class B digital device. Each product marketed, is identical to the representative unit tested and found to be compliant with the standards. Records maintained continue to reflect the equipment being produced can be expected to be within the variation accepted, due to quantity production and testing on a statistical basis as required by 47CFR 2.909. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.

Trade Name: Epson

Type of Product: Image Presentation Camera

Model: ELPDC05

58 Notices

FCC Compliance Statement

For United States Users

This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio or television reception. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause interference to radio and television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

Reorient or relocate the receiving antenna.

Increase the separation between the equipment and receiver.

Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.

Consult the dealer or an experienced radio/TV technician for help.

WARNING

The connection of a non-shielded equipment interface cable to this equipment will invalidate the FCC Certification of this device and may cause interference levels which exceed the limits established by the FCC for this equipment. It is the responsibility of the user to obtain and use a shielded equipment interface cable with this device. If this equipment has more than one interface connector, do not leave cables connected to unused interfaces. Changes or modifications not expressly approved by the manufacturer could void the users authority to operate the equipment.

For Canadian Users

This digital apparatus does not exceed the Class B limits for radio noise emissions from a digital apparatus as set out in the radio interference regulations of the Canadian Department of Communications.

Le prsent appareil numrique nmet pas de bruits radiolectriques dpassant les limites applicables aux appareils numriques de Class B prescrites dans le rglement sur le brouillage radioelctrique dict par le Ministre des Communications du Canada.

Notices 59

Warranty

Epson America, Inc. Limited Warranty

What Is Covered: Epson America, Inc. (Epson) warrants to the first end user customer of the Epson product enclosed with this limited warranty statement that the product, if purchased and used in the United States or Canada, conforms to the manufacturers specifications and will be free from defects in workmanship and materials for a period of two (2) years from the date of original purchase (except that the warranty period is 90 days for lamps). For warranty service, you must provide proof of the date of original purchase.

What Epson Will Do To Correct Problems: Should your Epson product prove defective during the warranty period, please bring the product securely packaged in its original container or an equivalent, along with proof of the date of original purchase, to your Epson Dealer or Epson Customer Care Center. Epson will, at its option, repair or replace on an exchange basis the defective unit, without charge for parts or labor. When warranty service involves the exchange of the product or of a part, the item replaced becomes Epson property. The exchanged product or part may be new or previously repaired to the Epson standard of quality. Exchange or replacement products or parts assume the remaining warranty period of the product covered by this limited warranty. However, each replacement lamp carries the limited 90-day warranty stated above.

What This Warranty Does Not Cover: This warranty covers only normal use in the United States and Canada. For lamps, 24-hour-per-day use causes unusual strain and is not considered normal use. This warranty is not transferable and will not apply to products purchased from an end user. This warranty does not cover consumables (e.g., fuses), other than lamps. Epson is not responsible for warranty service should the Epson label or logo or the rating label or serial number be removed or should the product fail to be properly maintained or fail to function properly as a result of misuse, abuse, improper installation, neglect, improper shipping, damage caused by disasters such as fire, flood, and lightning, improper electrical current, software problems, interaction with non-Epson products, or service other than by an Epson Authorized Servicer. Postage, insurance, or shipping costs incurred in presenting your Epson product for carry-in warranty service are your responsibility. If a claimed defect cannot be identified or reproduced in service, you will be held responsible for costs incurred.

THE WARRANTY AND REMEDY PROVIDED ABOVE ARE EXCLUSIVE AND IN LIEU OF ALL OTHER EXPRESS OR IMPLIED WARRANTIES INCLUDING, BUT NOT LIMITED TO, THE IMPLIED WARRANTIES OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE. SOME LAWS DO NOT ALLOW

60 Notices

THE EXCLUSION OF IMPLIED WARRANTIES. IF THESE LAWS APPLY, THEN ALL EXPRESS AND IMPLIED WARRANTIES ARE LIMITED TO THE WARRANTY PERIOD IDENTIFIED ABOVE. UNLESS STATED HEREIN, ANY STATEMENTS OR REPRESENTATIONS MADE BY ANY OTHER PERSON OR FIRM ARE VOID. EXCEPT AS PROVIDED IN THIS WRITTEN WARRANTY, NEITHER EPSON AMERICA, INC. NOR ITS AFFILIATES SHALL BE LIABLE FOR ANY LOSS, INCONVENIENCE, OR DAMAGE, INCLUDING DIRECT, SPECIAL, INCIDENTAL OR CONSEQUENTIAL DAMAGES, RESULTING FROM THE USE OR INABILITY TO USE THE EPSON PRODUCT, WHETHER RESULTING FROM BREACH OF WARRANTY OR ANY OTHER LEGAL THEORY. IF THE REMEDY ABOVE FAILS, EPSONS ENTIRE LIABILITY SHALL BE LIMITED TO A REFUND OF THE PRICE PAID FOR THE EPSON PRODUCT COVERED BY THIS LIMITED WARRANTY.

In Canada, warranties include both warranties and conditions.

Some jurisdictions do not allow limitations on how long an implied warranty lasts and some jurisdictions do not allow the exclusion or limitation of incidental or consequential damages, so the above limitations and exclusions may not apply to you.

This warranty gives you specific legal rights, and you may also have other rights which vary from jurisdiction to jurisdiction.

To locate an Authorized Epson Servicer nearest you, call the Epson Connection at (562) 276-4394 in the U.S. and (905) 709-3839 in Canada or write to: Epson America, Inc., P. O. Box 93012, MS: 6-33, Long Beach, CA 90809-3012.

SM

61

Index

Numerics 2x button, 27 3-D objects, presenting, 26

A Accessories, 44 Adjusting settings, 25 to 32 Aperture, 32 AUTO/MANUAL button, 27

B Batteries, installing, 13 Blank screen, 23 Blurry image, 45 Brightness, adjusting, 27, 31 Buttons

2x, 27 FOCUS, 26 IMAGE, 34 INPUT, 24 IRIS, 27 LAMP, 25 PAUSE, 29 POSI/NEGA, 33 PRESET, 34 ZOOM, 26

C Cables, 12, 44 Cleaning, 39 to 41 CLEAR MODE button, 28 CLOSE button, 27 Close-up lens, 40 COLOR/B&W button, 29 Computer, connecting to, 18 to 19

Connecting document camera to a computer, 18 to 19 to a monitor, 16 to 18 to a mouse, 19 to a projector, 16 to 18

Contrast, adjusting, 28

D Declaration of Conformity, 57 Default settings, restoring, 32 DIP switches, adjusting, 20, 44 Document camera

cleaning, 39 to 41 connecting, 16 to 19 folding and storing, 37 to 38 positioning, 14 specifications, 49 to 52 transporting, 42 turning off, 37 turning on, 22 to 23 unfolding, 15 to 16

E Electrical specifications, 50 Enlarging image, 26 to 27, 31 Environmental specifications, 50 Epson technical support, 9, 48

F FAR button, 26 FCC compliance statement, 58 Film, projecting, 32 to 33 Focusing image, 26, 31 Folding document camera, 37 to 38 Frame speed, 35, 49 Freezing image, 29, 31

G Gamma, 32, 49

62 Index

H Help, 9, 48

I Image

brightness, 27 changing to black and white, 29, 31 contrast, 28 enlarging and reducing, 26 to 27, 31 focusing, 26, 31 freezing, 29, 31 rotating, 28, 32 saving and recalling, 34 sources, selecting, 24 troubleshooting, 23, 44 to 46 white balance, 28, 32

Image Mate Software, 35 to 36 Infrared receiver, 14, 50 Iris, adjusting, 27, 31

L Lamps

specifications, 50 turning off and on, 24 to 25, 31

Lens cleaning, 39 to 40 specifications, 49

Lighting, adjusting, 24 to 25, 31

M MAIN button, 24 Monitor, connecting, 16 to 18 Mouse, connecting, 19 Moving document camera, 42

N NEAR button, 26 Negative film, projecting, 32 to 33 Noise, image, 28, 44 to 45 NORMAL button, 27

O On-screen display, adjusting settings, 30 to 32 OPEN button, 27 Options, ordering, 44

P Pausing display, 29, 31 Picture, see Image Pointer, using, 30 Ports, 17 to 19 POSI/NEGA button, 33 Positioning document camera, 14 Power, specifications, 50 PRESET buttons, 34 PrivateLine Support, 9, 48 Problems

blank screen, 23 image, 44 to 46 remote control, 47, 55 to 56

Projector, connecting, 16 to 18

R Recalling settings and images, 34 Reducing image, 26, 31 Registration, 9 Remote control

batteries, 13 specifications, 50 storing, 42 troubleshooting, 47, 55 to 56

Resolution, 7, 49 RGB buttons, 24 RGB ports, 17, 18 to 19 Rotating image, 28, 32

S Safety

instructions, 53 to 55 specifications, 51

Saving images, 34 settings, 32 to 34

Screen image, see Image

Index 63

Service, see Technical support Settings, saving, 32 to 34 Shooting speed, 35, 49 Slides, projecting, 32 to 33 Software, using, 35 to 36 Specifications

dimensions, 50 electrical, 50 environmental, 50 general, 49 lamps, 50 lens, 49 power, 50 remote control, 50 safety, 51 video formats, 51 to 52

Storing document camera, 37 to 38 Support, see Technical support S-VIDEO port, 18

T Technical support, 9, 48 TELE button, 26 Television, connecting, 16 to 18 Temperature requirements, 50 Transparencies, projecting, 32 to 33 Transporting, 42 Troubleshooting

image, 23, 44 to 46 remote control, 47, 55 to 56

Turning off document camera, 37 Turning on document camera, 22 to 23

U Unfolding document camera, 15 to 16 Unpacking document camera, 12

V Video camera, using camera as, 35 Video formats supported, 51 to 52 VIDEO port, 17 Video source, selecting, 24

W Warranty, 59 to 60 White balance, adjusting, 28, 32 WIDE button, 26

X X-rays, projecting, 32 to 33

Z Zooming image, 26 to 27, 31