Contents

Dovre 350CB3WB Stove Installation Manual PDF

1 of 32
1 of 32

Summary of Content for Dovre 350CB3WB Stove Installation Manual PDF

INSTALLATIEVOORSCHRIFTEN  EN GEBRUIKSAANWIJZING HOUTKACHEL INSTALLATION INSTRUCTIONS AND OPERATINGMANUAL WOOD STOVE INSTALLATION ET MODE DEMPLOI POELE A BOIS EINBAUANLEITUNG UND GEBRAUCHSANWEISUNG HOLZ-FEUERSTTTE INSTRUCCIONES DE INSTALACIN Y USO ESTUFA DE LEA ISTRUZIONI PER L'INSTALLAZIONE E L'USO STUFA A LEGNA

03.27898.200 - 02/2012

Houtkachel 350CB, 350CB3, 350CB3/WB,

360CB en 360CB3

Table of contents Introduction 3

Declaration of conformity 3

Safety 4

Installation requirements 4

General 4 Flue or chimney 4 Ventilation of the area 5 Floor and walls 6 Product description 6

Installation 8

Preparation 8 Fitting the legs (350CB and 360CB only) 8 Fitting the handle holder 8 Preparing the connection to chimney 9 Fitting the side panel (350CB3 and 360CB3 only) 10 Installing and connecting 11

Use 11

First use 11 Fuel 11 Lighting 11 Burning wood 12 Extinguishing the fire 13 Removing ashes 13 Fog andmist 14 Solving problems 14

Maintenance 14

Chimney 14 Cleaning andmaintenance 14

Appendix 1: Technical data 17

Appendix 2: Measurements 18

Appendix 3: Distance from combustible material 23

Appendix 4: Diagnostic diagram 26

Index 27

2 Subject to change because of technical improvements

Introduction Dear user, In buying this DOVRE heating appliance, you have chosen a high quality product. This product is part of a new generation of energy saving and environmentally friendly heating appliances. These appliances make optimal use of convection heat as well as thermal radiation (radiant heat).

Your DOVRE appliance has beenmanufactured with state-of-the-art production equipment. In the unlikely event of amalfunction, you can always rely on DOVRE for support and service.

The appliance is not to bemodified; always use original parts.

The appliance is intended for use in a living room. It must be connected hermetically to a well- functioning chimney.

We advise you to let an authorized and competent installation company install the appliance.

DOVRE cannot be held liable for any problems or damage resulting from incorrect installation.

Observe the following safety rules when installing and using the appliance.

In this manual, you can read how the DOVRE heating appliance can be installed, used andmaintained safely. Should you require additional information or technical data, or should you experience an installation problem, please contact your supplier first.

2012 DOVRE NV

Declaration of conformity

Notified body: 2013

The undersigned

Dovre nv, Nijverheidsstraat 18 B-2381Weelde hereby declares

that the wood stoves 350CB, 350CB3, 350CB3/WB, 360CB and 360CB3 have been produced in conformity with EN 13240.

Weelde 03-09-2005

Due to continuous product improvement, specifications of the appliance suppliedmay vary from the description in this brochure without prior notice.

DOVRE N.V. Nijverheidsstraat 18 Tel: +32 (0) 14 65 91 91 B-2381Weelde Fax: +32 (0) 14 65 90 09 Belgium E-mail: info@dovre.be

Subject to change because of technical improvements 3

Safety Please note: All safety regulations must be complied with strictly.

Carefully read the instructions for installation, use andmaintenance before you start using the appliance.

The appliancemust be installed in accordance with the laws and requirements of your country.

All local regulations and the regulations relating to national and European standards must be observed when installing the appliance.

Read the instructions for installation, use and maintenance supplied with the appliance.

It is preferable to have the appliance installed by an authorized and competent installation company. They will be aware of the applicable regulations and requirements.

The appliance is designed for heating purposes. All surfaces, including the glass and the connecting tube, can get very hot (over 100C)! For operation, use a so-called "cold hand" or an oven glove.

Don't place any curtains, clothes, laundry or other combustible materials on or near the appliance.

Don't use flammable or explosive substances near the appliance when it is in use.

Avoid a chimney fire by having the chimney swept regularly. Never burn wood with an open door.

In the case of a chimney fire: close all air inlets of the appliance and alert the fire brigade.

If the glass in the appliance is broken or cracked, it must be replaced before you can use the appliance again.

Make sure there is adequate ventilation in the room where the appliance is installed. The combustion will be incomplete in case of insufficient ventilation, which results in toxic gases being produced and spread through the room. See the chapter "Installation requirements" for more information on ventilation.

Installation requirements General

The appliancemust be connected tightly to a well- functioning chimney.

For the connectionmeasurements: see the appendix "Technical data".

Ask the fire brigade and/or your insurance company about any specific requirements and regulations.

Flue or chimney The flue or chimney is needed for:

Disposing of the combustion gases through natural draught.

The warm air in the flue or chimney is lighter than the outside air so it rises.

The intake of air, needed for the combustion of fuel in the appliance.

A poorly functioning flue or chimney can cause smoke to escape into the room when the door is opened. Damage caused by smoke emissions into the room is not covered by the warranty.

Do not connect multiple appliances (such as a boiler for central heating) to the same flue, unless local or national regulations allow this.

Ask your installer for advice regarding the flue. Refer to the European norm EN13384 for a correct calculation for the flue.

The fluemust satisfy the following requirements:

4 Subject to change because of technical improvements

The flue or chimney must bemade of fire resistant material, preferably ceramics or stainless steel.

The flue or chimney must be airtight and well cleaned and guarantee sufficient draught.

A draught/vaccuum of 15 - 20 Pa during normal operation is ideal.

Starting from the flue spigot, the fluemust run as vertically as possible. Changes in direction and horizontal pieces disrupt the outward flow of combustion gases andmay cause the deposit of soot.

The interior measurements should not be too big, to prevent the combustion gases from cooling down toomuch, thereby reducing the draught.

The flue or chimney must ideally have the same diameter as the connection collar.

For the nominal diameter: see the appendix "Technical data". If the smoke channel is well insulated, the diameter may be slightly bigger (up to 2x the section of the connection collar).

The section (area ) of the smoke channel must be constant. Wider segments and (in particular) narrower segments disrupt the outward flow of combustion gases.

When using a cover plate or exhaust hood: make sure that the cover does not restrict the flue outlet and that the cap does not impede the outward flow of combustion gases.

The chimney must end in a zone that is not affected by surrounding buildings, adjacent trees or other obstacles.

The chimney part outside the housemust be insulated.

The chimney must be at least 4 metres high.

As a rule of thumb: 60 cm above the ridge of the roof.

If the ridge of the roof is more than 3 metres away from the flue: stick to themeasurements in the following figure. A = the highest point of the roof within a distance of 3metres.

Ventilation of the area For good combustion, the appliance needs air (oxygen). That air is supplied via adjustable air inlets from the area where the appliance is installed.

The combustion will be incomplete in case of insufficient ventilation, which results in toxic gases being produced and spread through the area.

As a rule of thumb, the air supply should be 5.5 cm/kW. Extra ventilation is needed when:

The appliance is in an area that is well insulated.

There is mechanical ventilation, for example a central extraction system or an extraction hood in an open kitchen.

You can provide extra ventilation by having a ventilation louvre installed in the outside wall.

Make sure that other air consuming appliances (such as tumble-driers, other heating appliances or a bath room fan) have their own supply of outside air, or are switched off when you use the appliance.

Subject to change because of technical improvements 5

Floor and walls The floor on which the appliance is placedmust have sufficient load bearing capacity. For the appliance weight: see the appendix "Technical data".

Protect a flammable floor from heat radiation by means of a fireproof protective plate. See the appendix "Distance from combustible material".

Remove combustible material such as linoleum, carpets/rugs and similar materials below the fireproof protective plate.

Keep enough distance between the appliance and combustible materials such as wooden walls and furniture.

The connecting tube radiates heat too. Ensure that there is sufficient distance or a shield between the connecting tube and combustible material. The rule of thumb for a single-walled tube is a distance of 3x the diameter. If a lining shell is fitted around the tube, a distance of 1x the diameter is permissible.

Carpets and rugs must be at least 80 cm away from the fire.

Protect a flammable floor from possible falling ash in front of the fire with the aid of a fireproof protective plate. The protective plate must comply with national standards.

For the dimensions of the fireproof protective plate: see the appendix "Distance from combustible material".

For further requirements in connection with fire safety: see the appendix "Distance from combustible material".

Product description Model 350CB and 360CB

09.20015.078

7

6

1

2

3

4

5

1. Air slide for secondary combustion air, air-wash air

2. Door

3. Fire basket

4. Air slide for primary combustion air

5. Adjustable leg

6. Ashtray

7. Bolt

Features of model 350CB and 360CB

The appliance is supplied with height-adjustable legs.

The appliance can be connected to the chimney at the rear, at the upper side or at the side.

The appliance is supplied with a detachable handle.

In order to open the door, insert the detachable handle into the door; see the following figure.

6 Subject to change because of technical improvements

In order to prevent the handle becoming warm during use, the handle can be placed in the handle holder underneath the appliance's ash tray.

In order to remove the ash pan, the appliance is fitted with a cast-iron detachable handle, the so- called "cold hand"; see the following figure.

The appliance is supplied with a scraper for removing excess ash.

Model 350CB3 and 360CB3

09.20015.079

7

6

5

4

3

2

1

1. Air slide for secondary combustion air, air-wash air

2. Door

3. Fire basket

4. Air slide for primary combustion air

5. Ashtray

6. Bolt

7. Side glass

Features of model 350CB3 and 360CB3

Thesemodels have the same features as models 350CB and 360CB, with the exception of the following points:

The appliance is not height-adjustable.

You can replace the side glass (7) with a side panel. In this case, theminimum distance between the side and combustible material decreases from 80 cm to 40 cm. The side panel is supplied as standard.

Subject to change because of technical improvements 7

Model 350CB3/WB Features of model 350CB3/WB

This model has the same features as model 350CB3.

The appliance is installed with a log compartment that is shut off by a door.

Installation Preparation

Please check the appliance for damage caused during transport or any damage or defects immediately after delivery.

If you detect damage caused during transport or any other damage or defects, do not use the appliance and notify the supplier.

Remove the removable parts (fire-resistant inner plates, fire basket, ash pan, fire grate) from the appliance before you start installing the appliance.

By removing removable parts, it is easier to move the appliance and to avoid damage.

Note the location of those removable parts, so that you have no difficulties in installing the parts in the right place later on.

1. Open the door.

2. Remove the fire-resistant inner plates.

Cast iron inner plates protect the combustion chamber and dissipate heat to the environment.

Fitting the legs (350CB and 360CB only) If desired, you can fit the appliance with height- adjustable legs. Fit the legs to the appliance; see the following figure.

1. Tilt the appliance on its back.

2. Fit the height-adjustable legs (A) to the desired height using the bolts M6 (C) and washer (B) provided.

3. Fit the appliance on the newly-fitted legs in the original position.

Fitting the handle holder Fit the handle holder provided (A) to the base of the appliance using the washer (B) and the bolt M8 (C); see the following figure.

8 Subject to change because of technical improvements

Preparing the connection to chimney When connecting the appliance to the chimney you have the choice of connecting via either the upper side, the side or the rear. See the paragraphs "Connecting to the top side or on the side" and "Connecting to the rear".

The appliance is not supplied with a flue gas opening.

Sealant andmaterials supplied.

For Germany, the appliance is supplied with a connection collar with a diameter of 130mm.

When connecting to the upper side an opening has to bemade in the heat shield. At the spot when the opening has to bemade an incision has beenmade in the heat shield.

Preparation for connection at the rear side Make the necessary opening in the heat shield.

1. Unhook the heat shield from the appliance.

2. Make the opening in the heat shield by cutting the pre-cut section out of the heat shield using plate shears.

3. Replace the heat shield back onto the appliance.

Connecting to the upper side, rear side or on the side First make the flue gas opening in the appliance by removing the connection cover. Use the equipment provided: the tension piece, the washer, the nut and bolt; see following figure.

1. In the centre of the connection cover, drill a hole with a diameter of 10mm.

2. Place the tension piece and the bolt on the inner side of the connection cover.

3. Slide the washer over the bolt and tighten the nut onto the bolt.

On enamelled appliances, place a piece of cardboardmeasuring aminimum of 20 cm by 20cm between the washer and the appliance to protect against chipping of the enamel.

4. Tighten the nut by hand. Use a small amount of grease tomake it easier to turn the nut.

5. Using a ring spanner, tighten the nut so that the connection cover breaks out.

6. Oncemade a flue gas opening can be closed off again with the supplied shut-off cover (A). Use the mounting plate (C) and bolt M6x25 (D) to fit the cover to the appliance (B); see the following figure.

Subject to change because of technical improvements 9

7. Fit the connection collar (C) to the flue gas opening (D) using the two brackets supplied (E) and the fixingmaterials (A) and (B); see the following figure.

8. Use the supplied stove sealant to seal the connection collar and the cover to the appliance.

Fitting the side panel (350CB3 and 360CB3 only) If required, you can replace the side glass with a closed side panel that is supplied as standard; see the following figure for installation instructions.

In this case, theminimum distance between the side and combustible material decreases from 80 cm to 40 cm.

10 Subject to change because of technical improvements

Installing and connecting 1. Install the appliance in the right place, andmake

sure it is level.

2. Connect the appliance hermetically to the flue.

3. In the case of connection to outside air: connect the outside air supply to the connector you have fitted to the appliance.

4. Install all the parts you removed in the right places in the appliance.

Never use the appliance without the fire- resistant inner sheets.

The appliance is now ready for use.

Use First use When you use the appliance for the first time, make an intense fire and keep it going for a good few hours. This will cure the heat-resistant paint finish. This may result in some smoke and odours. You could open windows and doors for a while in the area where the appliance is located.

Fuel This appliance is only suitable for the burning of natural wood; sawn and chopped wood that is

sufficiently dry.

Do not use other fuels, as they can lead to serious damage to the appliance.

You are not allowed to use the following fuels, as they pollute the environment and because they heavily soil the appliance and flue, whichmay lead to a chimney fire:

Treated wood, such as scrap wood, painted wood, impregnated wood, preserved wood, plywood and chipboard.

Plastics, scrap paper and domestic waste.

Wood Hardwood, such as from oaks, beeches, birches and fruit trees, is the ideal fuel for your stove. This type of wood burns slowly with calm flames. Softwood contains more resins, burns faster and gives off more sparks.

Use dried wood that contains nomore than 20% moisture. The woodmust have dried for at least 2 years.

Saw the wood to size and split it when it is still fresh. Fresh wood is easier to split, and split wood dries more easily. Store the wood under a roof where the wind has wind free access.

Do not use dampwood. Damp logs do not produce heat as all of the energy is used in the evaporation of themoisture. This will result in a lot of smoke and soot deposits on the door of the appliance and in the chimney. The water vapour will condense in the appliance and can leak away through chinks in the appliance, causing black stains on the floor. It may also condense in the chimney and form creosote. Creosote is a highly flammable compound andmay cause a chimney fire.

Lighting You can check whether the flue has enough draught by lighting a ball of paper above the baffle plate. A cold flue often does not have enough draught and consequently, some smokemay escape into the room instead of up the chimney. By lighting the fire in the way described here, you can avoid this problem.

Subject to change because of technical improvements 11

1. Stack two layers of medium sized logs crosswise.

2. Stack two layers of kindling crosswise on top of the logs.

3. Place a firelighter cube in the lower layer of kindling and light the cube according to the instructions on the packaging.

4. Close the door of the appliance and open the primary air inlet and the secondary air inlet of the appliance. The primary air inlet is open if the operating knob has been pulled out. The secondary air inlet is open if air slider (C) has been slid left; see following figure.

5. Let this fire develop into a good blaze until there is glowing bed of charcoal. You can then add fuel and adjust the appliance, see the chapter "Stoking with wood".

Burning wood After you have followed the instructions for lighting :

1. Slowly open the door of the appliance.

2. Spread out the charcoal bed evenly across the bottom of the fire compartment.

3. Stack a few logs on the charcoal bed.

Open stacking

If the logs are stacked openly, the wood will burn quickly as the oxygen can reach each log easily. If you want to use the stove for a short while, make an open stack.

Compact stacking

If the logs are stacked tightly, the wood will burnmore slowly as the oxygen can only reach some logs easily. If you want to burn wood for a longer period, make a compact stack.

12 Subject to change because of technical improvements

4. Close the door of the appliance.

5. Close the primary air inlet and leave the secondary air inlet open.

Fill the appliance up to one third capacity.

Advice Never burn wood with an open door.

Regularly burn wood with intense roaring fires.

If you frequently have low intensity fires, tar and creosotemay be deposited in the chimney. Tar and creosote are highly combustible substances. Thicker layers of these substances might catch fire when the temperature in the chimney increases suddenly and steeply. Therefore it is necessary for the fire to regularly burn very intensely, so that layers of tar and creosote disappear. Low intensity fires also cause tar deposits on the stove window and door. When the outside temperature is not very low, it is better to burn wood intensely for a few hours instead of having a low intensity fire for a long period of time.

Control the air supply with the secondary air inlet.

The secondary air inlet not only supplies air to the fire but to the glass as well, so that it does not get dirty so quickly.

Open the primary air inlet for the time being if the air supply by the secondary air inlet is inadequate or if you want to fan the fire.

It is better to add a small amount of logs regularly than to addmany logs at the same time.

Extinguishing the fire Do not add fuel and just let the fire go out. If a fire is damped down by reducing the supply of air, harmful substances will be produced and released. Therefore, let the fire go out naturally. Keep an eye on the fire until it has gone out. When the fire has died completely, all air inlets can be closed.

Removing ashes After the wood has been burnt, a relatively small amount of ashes is left over. This bed of ashes is a good insulating layer for the bottom of the fire compartment and improves combustion. Therefore, you can leave a thin layer of ashes on the bottom of the fire compartment.

However, the air supply through the bottom of the fire compartment must not be impeded and no ash should be allowed to accumulate behind a cast iron inner plate. Therefore, remove any excess ash frequently.

1. Open the door of the appliance.

2. Use the supplied scraper to open the de-ashing grate; see the following figure.

3. Using the scraper, sweep the redundant ashes through the de-ashing grate into the ashtray underneath; see the following figure.

Subject to change because of technical improvements 13

4. Close the ash removal port.

5. Remove the ash pan using the cast-iron "cold hand" and empty the ash pan; see the following figure.

6. Install the ashtray and close the appliance door.

Fog and mist Fog andmist hinder the flow of flue gases through the flue. Smoke can blow back and cause a stench. If it is not strictly necessary, it is better not to use the stove in foggy andmisty weather.

Solving problems Refer to the appendix "Diagnostic diagram" to solve any problems in using the appliance.

Maintenance Follow themaintenance instructions in this chapter to keep the appliance in good condition.

Chimney In many countries, people are legally required to have their chimney checked andmaintained.

At the beginning of the heating season: have the chimney swept by an expert.

During the heating season and after the chimney has not been used for a long time: have the chimney checked for soot deposits.

After the heating season: seal off the chimney with a ball of paper.

Cleaning and maintenance Do not clean the appliance when it is still warm.

Clean the exterior of the appliance with a dry lint- free cloth.

At the end of the heating season, you can clean the interior of the appliance thoroughly:

If necessary, first remove the fire-resistant inner plates.

If necessary, clean the air supply ducts.

Remove the baffle plate at the top of the appliance and clean it. See the chapter "Installation" for instructions on removing and installing the baffle plate.

Checking fire-resistant inner plates The fire-resistant inner plates are consumables and subject to wear. Check the fire-resistant inner plates frequently and replace them when necessary.

See the chapter "Installation" for instructions on removing and installing the inner plates.

The insulating vermiculite inner plates may develop hairline cracks, but that does not affect their performance adversely.

Cast-iron inner plates go a long way if you frequently remove the ash that may pile up behind them. If accumulated ash behind a cast-iron plate is not removed, the plate cannot dissipate the heat anymore to its surroundings and that may cause the plate to warp or crack.

Never use the appliance without the fire- resistant inner plates.

Removing the baffle plate The baffle plate is secured with a bolt located between the rear connection and the secondary air duct. The bolt is fixed to the baffle plate.

1. Remove the nut on the rear side; see the following figure.

14 Subject to change because of technical improvements

2. Pull the baffle plate forwards so that the bolt comes free from the rear side.

3. Remove the baffle plate via the front door.

As the baffle plate has notches on both sides of it, the baffle plate can be taken along the ridges on the side walls and removed from the appliance without a problem.

Cleaning glass Dirt clings less easily to well-cleaned glass. Proceed as follows:

1. Remove dust and loose soot with a dry cloth.

2. Clean the glass with stove window cleaner: a. Apply stove window cleaner to a kitchen

sponge, rub down the entire glass surface and give the cleaning agent time to react.

b. Remove the dirt with amoist cloth or kitchen tissue.

3. Clean the glass again with a normal glass cleaning product.

4. Rub the glass clean with a dry cloth or kitchen tissue.

Do not use abrasive or aggressive products to clean the glass.

Wear household gloves to protect your hands.

If the glass in the appliance is broken or cracked, it must be replaced before you can use the appliance again.

Make sure that no stove window cleaner runs between the glass and the cast-iron door.

Lubrication Although cast-iron is slightly self-lubricating, you will still have to lubricatemoving parts frequently.

Lubricate themoving parts (such as guide systems,hinge pins, latches and air slides) with heat resistant grease that is available in the specialist trade.

Adjusting the air slider If the air slider (C) of the secondary air inlet does not move easily, you can adjust the air slider using the two screws (A) and (B) in the front plate; see following figure.

Touching up the finish Small areas of damaged paint finish can be touched up with a spraying can of special heat-resistant paint finish available from your supplier.

Checking the seal Check whether the sealing rope of the door is still in good condition and works well. The sealing rope is subject to wear and needs to be replaced in time.

Check the appliance for air leaks. Close any chinks with stove sealant.

Subject to change because of technical improvements 15

Let the sealant harden fully before you start a fire in the appliance, because otherwise any moisture in the sealant will form bubbles in the sealant and cause a new air leak.

16 Subject to change because of technical improvements

Appendix 1: Technical data

Model 350CB and 350CB3

360CB and 360CB3 350CB3/WB

Nominal output 6 kW 8 kW 6 kW

Flue connection (diameter) 125mm 125mm 125mm

Flue connection Germany (diameter) 130mm 130mm 110mm

Weight +/- 95 kg +/- 130 kg +/- 130 kg

Recommended fuel Wood Wood Wood

Fuel property, max. length 30 cm 40 cm 30 cm

Mass flow of flue gases 6.6 g/s 8.2 g/s 6.6 g/s

Temperature increasemeasured inmeasuring section 298 K 297 K 298 K

Temperaturemeasured downstream from the flue spigot 442 438 442

Minimum draught 12 Pa 10 Pa 12 Pa

CO emission (13%O2) 0,10% 0,10% 0,10%

NOx emission (13%O2) 125mg/Nm 90mg/Nm 125mg/Nm

CnHm emission (13%O2) 82mg/Nm 113mg/Nm 82 g/Nm

Particulate emission 10mg/Nm 39mg/Nm 10mg/Nm

Particulate emission in accordance with NS3058- NS3059 3.58 gr/kg 7.86 gr/kg 3.58 gr/kg

Efficiency 77% 75% 77%

Subject to change because of technical improvements 17

Appendix 2: Measurements

350CB

09.20017.017

18 Subject to change because of technical improvements

350CB3

09.20017.018

Subject to change because of technical improvements 19

350CB3/WB

09.20017.019

20 Subject to change because of technical improvements

360CB

09.20017.020

Subject to change because of technical improvements 21

360CB3

09.20017.021

22 Subject to change because of technical improvements

Appendix 3: Distance from combustible material 350CB, 350CB3, 350CB3/WB - Minimum distances in millimetres

09.20017.036

* Protective (insulated) connection pipe

Combustible material

Incombustible material, thickness 100mm

Subject to change because of technical improvements 23

360CB en 360CB3 - Minimum distances in millimetres

09.20017.037

* Protective (insulated) connection pipe

Combustible material

Incombustible material, thickness 100mm

24 Subject to change because of technical improvements

350CB, 350CB3, 350CB3/WB, 360CB and 360CB3 - Fireproof protective plate dimensions

A

B B

09-20002-004

Minimal dimensions of fireproof protective plate

A (mm) B (mm)

Din 18891 500 300

Germany 500 300

Finland 400 100

Norway 300 100

Subject to change because of technical improvements 25

Appendix 4: Diagnostic diagram Problem

Wood does not keep burning

Gives off insufficient heat

Smoke emissions into the room when adding wood

Fire in appliance is too intense, is hard to adjust

Deposit on the glass

Possible cause Possible solution

Insufficient draught A cold flue usually fails to create sufficient draught. Follow the instructions for lighting in the "Use" chapter; open a window.

Wood too damp Usewoodwith nomore than 20%moisture.

Piecesof wood too big Use small piecesof kindling. Use split logsno larger than 30 cm in circumference.

Wood stacked up incorrectly Stackup the wood in a way that allowsan adequate air flow between the logs (open stacking, see "Burning wood")

Chimneydoesnot work properly

Checkwhether the chimneymeets the requirements: at least 4 metreshigh, right diameter, well insulated, smooth inside, not too manybends, no obstructions in chimney (bird's nest, toomuch soot deposit), hermetically tight (no chinks).

Chimneystack incorrect Sufficiently high above the roof, no obstacles in its vicinity

Air inlets set incorrectly Open the air inlets completely.

Appliance connected to chimney incorrectly Connection should be hermetically tight.

Vacuum in area where appliance is installed Switch off extraction systems.

Insufficient supply of fresh air Provide an adequate air supply; if necessary use connection to outside air.

Adverse weather conditions? Inversion (reversed air flow in chimney because of a high outside temperature), extremewind velocities

We recommend you don't use the appliance in the case of inversion. Install an extra hood on the flue to increase the draught if need be.

Draught in the living room Avoid draught in the living room, do not place the appliance near a door or heating air ducts.

Flames touch the glass Make sure the wood doesnot lie too close to the glass. Slide the primary air inlet cover closer to the "Closed" position.

Appliance is leaking air Check the door seals and the appliance joints.

26 Subject to change because of technical improvements

Subject to change because of technical improvements 27

Index A

Adding fuel 13 Adding wood smoke emissions into the room 26

Air inlets 12 adjusting 15

Air leak 15 Air supply for fire 13 Ash pan open 14

Ashes remove 13

B

Baffle plate removing 14

Burning wood 12 add fuel 13 adding logs 12 appliance is hard to adjust 26 fire is too intense 26 insufficient heat 14, 26

C

Carpet 6 Chimney height 5 sweep 14

Chinks in appliance 15 Clean glass 15

Cleaning appliance 14

Combustible material distance from 23

Connecting to the chimney 9 Connection measurements 18

Connection collar fitting 10

Connection cover removing 9

Connection to chimney rear side 9

Control air supply 13 Cover on flue 5 Creosote 13

D

Dampwood 11 De-ashing grate removal 13

Door sealing rope 15

Draught 17 Drying of wood 11

E

Efficiency 17

F

Filling height 13 Finishing coat, maintenance 15 Fire extinguishing 13 lighting 11

Fire-resistant inner plates maintenance 14

Fire-resistant inner sheets warning 11

Fire going out 13 Fire safety distance from combustible material 23 floor 6 furniture 6 walls 6

Floors fire safety 6 load bearing capacity 6

Flue connection diameter 17 connection to 11 maintenance 14 requirements 4

Flue gas mass flow 17

Flue gas opening shutting off 9

Fog, do not burn wood 14

Fuel adding 13 adding wood 13 necessary amount 14 suitable 11 unsuitable 11

G

Glass clean 15 deposit 26

H

Handle holder fitting 8

Heat shield making opening 9 removing 9

Heat, insufficient 14 Heat,insufficient 26 Hood on the flue 5

I

Installation measurements 18

K

Kindled fire 11 Kindling 26

L

Legs fitting 8

Lighting 11 Load bearing capacity of floor 6 Lubricant 15 Lubricate 15

M

Maintenance chimney 14 clean glass 15 cleaning the appliance 14 fire-resistant inner plates 14 lubrication 15 sealing 15

Measurements 18 Mist, do not burn wood 14

N

Nominal output 14, 17

O

Open ash pan 14

P

Paint finish 11 Particulate emission 17 Prevent a chimney fire 13 Primary air inlet 12

R

Removal of ashes 13 Remove ashes 13

S

Scraper for removing ash 7 Screens clean 15 deposit 26

Sealing rope for door 15 Secondary air inlet 12 Side glass replacing 10

Side panel fitting 10

Smoke on first use 11

Smoke emissions into the room 4, 26 Softwood 11 Solving problems 14, 26 Stacking logs 12 Storing wood 11 Stove window cleaner 15 Suitable fuel 11 Supply of outside air 5 connection to 11

Sweep chimney 14

T

Tar 13 Temperature 17

28 Subject to change because of technical improvements

Subject to change because of technical improvements 29

Temperature increase measuring section 17

U

Unsuitable fuel 11

V

Ventilation 5 rule of thumb 5

Ventilation louvre 5

W

Walls fire safety 6

Warning chimney fire 4, 11, 13 combustible materials 4 fire-resistant inner plates 11 glass broken or cracked 4, 15 hot surface 4 regulations 4 stove window cleaner 15 terms and conditions for insurance 4 ventilation 4-5

Weather conditions, do not burn wood 14 Weight 17 Wood

Manualsnet FAQs

If you want to find out how the 350CB3WB Dovre works, you can view and download the Dovre 350CB3WB Stove Installation Manual on the Manualsnet website.

Yes, we have the Installation Manual for Dovre 350CB3WB as well as other Dovre manuals. All you need to do is to use our search bar and find the user manual that you are looking for.

The Installation Manual should include all the details that are needed to use a Dovre 350CB3WB. Full manuals and user guide PDFs can be downloaded from Manualsnet.com.

The best way to navigate the Dovre 350CB3WB Stove Installation Manual is by checking the Table of Contents at the top of the page where available. This allows you to navigate a manual by jumping to the section you are looking for.

This Dovre 350CB3WB Stove Installation Manual consists of sections like Table of Contents, to name a few. For easier navigation, use the Table of Contents in the upper left corner.

You can download Dovre 350CB3WB Stove Installation Manual free of charge simply by clicking the “download” button in the upper right corner of any manuals page. This feature allows you to download any manual in a couple of seconds and is generally in PDF format. You can also save a manual for later by adding it to your saved documents in the user profile.

To be able to print Dovre 350CB3WB Stove Installation Manual, simply download the document to your computer. Once downloaded, open the PDF file and print the Dovre 350CB3WB Stove Installation Manual as you would any other document. This can usually be achieved by clicking on “File” and then “Print” from the menu bar.