DeLonghi EC685 BK Instruction Manual v2 PDF

1 of 8
1 of 8

Summary of Content for DeLonghi EC685 BK Instruction Manual v2 PDF

15

1. DESCRIPTION (page 3) The terminology below will be used repeatedly on the following pages. 1.1 Description of the appliance A1. Water tank lid A2. Tank extraction handle A3. Water tank A4. Cup warmer A5. Boiler outlet A6. ON/OFF switch A7. Cup tray A8. Drip tray full indicator A9. Drip tray A10. Mugs or glasses tray A11. Steam dial A12. Hot water/steam spout A13. Hot water/steam connection nozzle A14. Cappuccino maker selection ring A15. Hot water/steam connection tube

1.2 Description control panel B1. One cup button B2. ON light on button (white) B3. Two cups button B4. ON light on button (white) B5. Steam button B6. ON light on button (white) B7. Descale light (orange)

1.3 Description of the accessories C1. Filter holder C2. 1 cup filter ( symbol under filter) C3. 2 cup filter ( symbol under filter) C4. Pod filter ( symbol under filter) C5. Measure/presser C6. Water softener filter (*not included, can be purchased

from authorised Customer Services)

2. FILLING THE WATER TANK Please note: Before first use, wash all the accessories and water tank with warm water. 1. Extract the tank by pulling it upwards (fig. 1). 2. Open the lid and fill the tank with fresh clean water, taking

care not to exceed the MAX level (fig. 2). Put the tank back in the appliance, pressing lightly to open the valves located on the bottom of the tank.

3. More simply, the tank can also be filled without removing it, pouring the water directly from a jug.

Important: Never operate the appliance without water in the tank or with- out the tank.

Please note: It is normal for there to be water in the space under the tank. This should therefore be dried regularly with a clean sponge.

3. FIRST USE At first use, rince the internal circuit as follows: 1. Turn the appliance on by pressing the ON/OFF switch (fig.

3). The appliance performs a self-diagnosis cycle, indicated by sequential flashing of the three buttons.

2. The and lights flash to indicate the appliance is heating up. When the lights stop flashing and remain on steadily, the appliance is ready for operating the rinse.

3. Attach the filter holder to the appliance (fig. 9). 4. Place a container with a minimum capacity of 500 ml

under the boiler outlet (A5) (fig. 4) and press the button. Repeat this operation 5 times.

5. Empty the container and put it under the hot water/steam spout (A12) (fig. 4).

6. Turn the hot water/steam dial to the position (fig. 5) and deliver to empty the water tank (A3); then turn the knob to the position.

4. PROGRAMMING THE SETTINGS MENU To access the menu, make sure the appliance is ready for use,

then press and hold the button for 10 seconds until the three buttons flash in sequence: The appliance is now in programming mode. Set the coffee maker as you wish, then exit the settings menu by waiting for 15 seconds.

Please note: If no selections are made for 15 seconds, the appliance automat- ically exits programming and is ready for use again.

4.1 Setting coffee temperature To modify the temperature of the water used to make the coffee, proceed as follows: 1. Access the settings menu;

2. Press the button to enter the coffee temperature selection mode. The lights corresponding to the current selection come on:

16

low

medium

high

3. The lights start flashing in sequence; 4. Press the button corresponding to the required

temperature:

low medium high

5. The button flashes to indicate that the selection has been saved.

The appliance exits the menu and is ready for use.

4.2 Setting water hardness The light (B7) indicating that the coffee maker needs descaling comes on after a period of operation established according to water hardness. The appliance can also be programmed according to the hard- ness of the mains water in the various regions so that descaling needs to be performed more or less frequently. Proceed as follows: 1. Access the settings menu; 2. Press the button to enter the water hardness selec-

tion mode. The lights corresponding to the current selec- tion come on:

soft

medium

hard

3. The lights start flashing in sequence; 4. Press the button corresponding to the water hardness in

your area:

soft water medium water hard water

<10dH 10dH - 20dH >20dH

<18fH 18fH - 36fH >36fH

<180mg/l CaCo3 180-360mg/l CaCo3 >360mg/l CaCo3

- The button flashes to indicate that the selection has been saved.

The appliance exits the menu and is ready for use.

4.3 Adjusting auto-off (stand-by) To save energy, an auto-off function turns the appliance off when not used for a long period. To turn it back on again, press any button on the control panel. 1. Access the settings menu;

2. Press the button to enter the auto-off time selection mode. The lights corresponding to the current selection come on:

9 min

30 min

3 hours 3. The lights start flashing in sequence; 4. Press the button corresponding to the required time:

9 min 30 min 3 hours

5. The button flashes to indicate that the selection has been saved.

The appliance exits the menu and is ready for use.

4.4 Default values (reset) This resets all menu settings and programmed quantities back to the default values. To reset the default values, proceed as follows: 1. Position the steam spout over the drip tray; 2. Access the settings menu; 3. Turn the steam dial to the position;

4. Press the button. The three lights flash simulta- neously to confirm that the original settings have been restored.

5. The and lights flash to indicate that the steam dial must be closed again (symbol).

When the steam dial has been closed, the appliance is ready for use.

5. HOW TO MAKE ESPRESSO COFFEE 5.1 Tips for a hotter coffee For hotter espresso coffee, you should: You are recommended to warm the cups before making

coffee by rinsing them with a little hot water. Attach the filter holder to the appliance with the filter in

place but without adding coffee.Using the same cup as will later be used to make the coffee, press the 1 cup button and deliver hot water into the cup to heat it.

Raise the coffee temperature in the settings menu.

17

Rest the cups you will be using on the cup warmer (A4) which becomes hot during operation.

5.2 How to prepare espresso coffee using pre- ground coffee

1. Place the ground coffee filter (C2 or C3) in the filter holder (fig. 6). To make one coffee, use the filter with the symbol on the bottom, to make two coffees, use the filter with the symbol on the bottom.

2. To make just one coffee, place one level measure of pre- ground coffee (about 7 g) in the filter (fig. 7). To make two coffees, place two loosely filled measures (about 7+7 g) of pre-ground coffee in the filter. Fill the filter a little at a time to prevent the pre-ground coffee from overflowing.

Important: For correct operation, before filling with pre-ground coffee, make sure there are no coffee residues left in the filter from the last time you made coffee. 3. Distribute the pre-ground coffee evenly and press lightly

with the presser (fig. 8). Correct pressing of the pre-ground coffee is essential to

obtain a good espresso. If you press too firmly, the coffee will be delivered slowly and will be strong. If you press too lightly, the coffee will be delivered quickly and will be weak.

4. Remove any excess coffee from the rim of the filter holder and attach the filter holder to the appliance. To attach cor- rectly, align the filter holder handle with the INSERT sym- bol (fig. 9), attach the filter holder and rotate the handle towards the right until aligned with the CLOSE symbol.

5. Place the cup or cups under the filter holder spouts (fig. 10).

6. Make sure the lights corresponding to the coffee buttons

are on, then press the or coffee button. The appliance proceeds to make the coffee and delivery is in- terrupted automatically.

7. To remove the filter holder, turn the handle from right to left.

Danger of burns! To avoid splashes, never remove the filter holder while the appliance is delivering coffee. Always wait for a few seconds after delivery.

5.3 How to make espresso coffee using pods

Please note: Use pods conforming to the ESE standard, indicated on the pack by the following symbol.

The ESE standard is a system accepted by lead- ing pod producers and enables espresso coffee to be prepared simply and cleanly.

1. Place the filter for coffee pods (with the symbol on the bottom) in the filter holder.

2. Insert the pod, centring it as far as possible on the filter (fig. 11). Always follow the instructions on the pod pack to position the pod on the filter correctly.

Proceed as described in points 4 to 6 in the previous section.

Please note: While the appliance is making coffee, delivery can be in-

terrupted at any moment by pressing the coffee button pressed previously.

At the end of delivery (within 3 seconds), to increase the amount of coffee in the cup, press and hold the coffee but- ton pressed previously. Delivery is automatically interrupt- ed after a few seconds.

To remove the filter holder, turn the handle from right to left.

Danger of burns! To avoid splashes, never remove the filter holder while the appliance is delivering coffee. Always wait for a few seconds after delivery.

5.4 Programming the quantities of coffee in the cup

The appliance is set by default to automatically deliver standard quantities. To change these quantities, proceed as follows: 1. Place one or two cups under the filter holder spouts.

2. Press and hold the button you want to programme ( or ). The coffee maker starts delivering coffee and the other coffee button flashes to indicate that the appli- ance is in programming mode.

3. Once the required quantity of coffee has been delivered into the cup, release the button. Delivery stops and the light flashes to indicate that the quantity has been saved correctly.

4. When the two coffee lights come on steadily, the appliance is ready for use.

6. HOW TO MAKE CAPPUCCINO 1. Prepare the espresso coffees as described in the previous

sections, using sufficiently large cups. To use tall glasses, remove the drip tray and stand the glasses on the glasses tray (A10);

18

2. Press the button (fig. 12). The light flashes; 3. In the meantime, fill a recipient with about 100 grams of

milk for each cappuccino to be prepared. For a denser more even froth, you must use skimmed or partially skimmed milk at refrigerator temperature (about 5C). In choosing the size of the recipient, bear in mind that the milk doubles or triples in volume (fig. 13).

4. Make sure the cappuccino maker selection ring (A14) is in the "CAPPUCCINO" position (fig. 14);

5. Wait for the light corresponding to the button to come on steadily, indicating that the boiler has reached the ideal temperature to produce steam.

6. Position an empty container under the cappuccino maker and open the dial for a few seconds to eliminate any air left in the circuit. Close the dial again.

7. Place the recipient containing the milk under the cappucci- no maker.

8. Immerse the cappuccino maker in the milk container. Never immerse the black ring (fig. 15). Turn the dial to the

position. Steam is delivered from the cappuccino maker, giving the milk a creamy frothy appearance (fig. 16). To obtain a creamier froth, immerse the cappuccino maker in the milk and rotate the container with slow up- ward movements.

9. When the required temperature (the ideal is 60C) and froth density is reached, interrupt steam delivery by turn- ing the steam dial clockwise.

10. Pour the frothed milk into the cups containing the espresso coffee prepared previously. The cappuccino is ready. Sweet- en to taste and if desired, sprinkle the froth with a little cocoa powder.

Please note: to prepare more than one cappuccino, first make all the

coffees then at the end prepare the frothed milk for all the cappuccinos;

to exit the steam function, press any button. The and lights flash to indicate that the temperature is too high to make coffee (see section "Cooling the boiler).

You should not deliver steam for more than 60 seconds.

7. MAKING HOT MILK To make hot milk without froth, proceed as described in the above section, making sure the cappuccino maker selection ring (A14) is positioned upwards in the "HOT MILK" position.

8. CLEANING THE CAPPUCCINO MAKER AFTER USE Important: For hygiene reasons, the cappuccino maker should always be cleaned after use. Proceed as follows: 1. Turn the steam dial to deliver a little steam for a few sec-

onds (points 2, 5 and 6 of the previous section). This caus- es the cappuccino maker to discharge any milk left inside. Press the ON/OFF button to turn the appliance off.

2. Wait a few minutes for the cappuccino maker to cool down. With one hand, hold the cappuccino maker tube firmly, with the other, release the cappuccino maker by turning it clockwise, then pull off downwards (fig. 17).

3. Remove the rubber steam connection nozzle from the spout by pulling it downwards (fig. 18).

4. Push the ring upwards and make sure the two holes shown by the arrows in fig. 19 are not blocked. If necessary, clean with a pin;

5. Replace the nozzle, move the ring downwards and put the cappuccino maker back on the connection nozzle, turning it and pushing it upwards until it is attached.

9. COOLING THE BOILER To make coffee again immediately after frothing milk, the boil- er must first be cooled or the coffee will be burnt. Proceed as follows: place a container under the cappuccino maker; open the steam dial to deliver hot water and cool the

boiler; hot water delivery is interrupted automatically when the

boiler is cool. When the pump stops operating and no more water is delivered, close the steam dial.

The coffee maker is now ready for use.

10. HOT WATER 1. Press the ON/OFF button (fig. 3) to turn the appliance on.

Wait for the coffee lights to come on steadily. 2. Place a recipient under the cappuccino maker. 3. Turn the dial to the position. Hot water is delivered

from the cappuccino maker. 4. To stop hot water delivery, close the dial and press any

button.

You should not deliver hot water for more than 60 seconds.

11. CLEANING 11.1 Cleaning the machine The following parts of the machine must be cleaned regularly:

19

- drip tray (A9) - the coffee filters (C2, C3 and C4); - the boiler outlet (A5); - water tank (A3); - the cappuccino maker (A15) as described in section "8.

Cleaning the cappuccino maker after use;

Important! Do not use solvents, abrasive detergents or alcohol to clean

the coffee machine. Do not use metal objects to remove encrustations or coffee

deposits as they could scratch metal or plastic surfaces. If the appliance is not used for more than one week, before

using it again, we strongly recommend you perform a rinse cycle as described in section 3. first use.

Danger! While cleaning, never immerse the coffee maker in water.

It is an electrical appliance. Before cleaning the outside of the appliance, turn it off,

unplug from the mains socket and allow to cool.

11.2 Cleaning the drip tray Important! The drip tray is fitted with a level indicator (red) showing the level of water it contains (fig. 20). Before the indicator protrudes from the cup tray, the drip tray must be emptied and cleaned otherwise the water may overflow the edge and damage the appliance, the surface it rests on or the surrounding area. 1. Remove the drip tray (fig. 21). 2. Remove the cup tray (A7), empty the water and clean the

drip tray with a cloth, then reassemble the drip tray. Ex- tract the mugs or glasses tray (A10), clean with water, dry and put back in the machine;

3. Put the drip tray back in place.

11.3 Cleaning the coffee filters Clean the coffee filters weekly: 1 and 2 cup filters 1. Extract the perforated filter by pulling the tab (fig. 22); 2. Rinse the filters under running water (fig. 23); 3. Make sure the holes are not blocked. If necessary, clean

with a pin (figs. 23 and 24); 4. Place the perforated filter in the filter housing and press as

far as it will go. Pod filter Rinse under running water. Make sure the holes are not blocked. If necessary, clean with a pin (figs. 23 and 24).

11.4 Cleaning the boiler outlet After every 200 coffees, rinse the boiler outlet by delivering about 0.5 l of water from the boiler outlet (press the coffee but- ton without using ground coffee).

11.5 Other cleaning operations 1. Do not use solvents or abrasive detergents to clean the cof-

fee maker. Use a soft damp cloth only. 2. Clean the filter holder cup.

11.6 Cleaning the water tank 1. Clean the water tank regularly (about once a month) and

whenever you replace the water softener filter (C6, *if pro- vided) with a damp cloth and a little mild washing up liquid;

2. Remove the filter (*if present) and rinse with running water;

3. Put the filter (*if provided) back in the appliance, fill the tank with fresh water and replace the tank;

4. (Models with water softener filter only) Deliver about 100 ml of water.

Danger! While cleaning, never immerse the coffee maker in water. It is an electrical appliance.

11.7 Descale Descale the appliance when the orange light on the but- ton comes on.

Important! Before use, read the instructions and the labelling on the

descaler pack. You should use De'Longhi descaler only. Using unsuitable

descaler and/or performing descaling incorrectly may re- sult in faults not covered by the manufacturer's guarantee.

Proceed as follows: 1. (IF PRESENT, REMOVE THE WATER SOFTENER FILTER). Fill

the tank with the descaler solution, obtained by diluting the descaler provided with water (fill the water tank up to the MAX level).

2. Press the ON/OFF button.

25

20

13. EXPLANATION OF LIGHTS Lights Operation Explanation of lights

The ON/OFF button is turned on The appliance performs a self-diagnosis cycle, indicated by sequential flashing of the lights

When the appliance is turned on Flashing lights: the appliance is heating up to make coffee Lights on steadily: the appliance is ready to make coffee The lights flash rapidly: the tank is empty or the appliance will not make coffee. See the section 2. Filling the water tank

3. Make sure the filter holder is not attached and position a recipient under the hot water spout and boiler outlet (A5) (fig. 25).

4. Wait for the and lights to come on steadily, indicating that the appliance is ready for use.

5. Press and hold the button for 10 seconds until the three buttons flash in sequence.

6. Turn the steam dial to the position.

7. Press the button to start descaling. 8. The descale programme starts and the descaler liquid

comes out of the water spout. The descale programme removes limescale deposits from inside the appliance by automatically performing a series of rinses and pausesuntil the tank is completely empty.

Please note: During descaling, to clean the boiler outlet, close the steam dial from time to time to deliver small quantities of descaler from the boiler outlet.

9. The appliance stops operation and the orange light continues to flash, indicating that descaling is still underway.

10. The appliance is now ready for rinsing through with clean water. Extract the water tank, empty, rinse under running water, fill with fresh water up to the MAX level and put back in the appliance (If used, insert the water softener filter).

11. Empty the container used to collect the descaler solution and replace it empty under the hot water spout.

12. Make sure the steam dial is in the position, then

press the button to start rinsing.

Please note: During rinsing, to clean the boiler outlet, close the steam dial from time to time to deliver small quantities of water from the boiler outlet. 13. When the water tank is empty, the orange light goes out

and descaling is complete. 14. Make sure the steam dial is in the closed position (

symbol). The appliance is ready for use.

Please note! If the descaling cycle is not completed correctly (e.g. no

electricity) we recommend repeating the cycle; If the water tank has not been filled to the MAX level, at the

end of descaling, the appliance requests a further rinse to guarantee that the descaler solution has been completely eliminated from the machine's internal circuits.

Repair of damage to the coffee maker caused by limescale is not covered by the guarantee unless descaling is performed regular- ly as described above.

12. TECHNICAL DATA Mains voltage: ........................................ 220-240V~50/60Hz Absorbed power: ......................................................... 1350 W Pressure: ....................................................................... 15 bar Water tank capacity: ............................................................1 l Size LxHxD.......................................... 149x305x330 (414)mm Weight .........................................................................4.04 kg

None of the components or accessories is dish- washer safe.

21

14. TROUBLESHOOTING Problem Cause Solution

No espresso coffee is delivered No water in the tank Fill the tank

The holes in the filter holder are blocked Clean the filter holder spout holes

The filter is blocked Clean as described in section 11.3 Cleaning the coffee filters

The tank has been inserted incorrectly and the valves on the bottom are not open

Press the tank down lightly to open the valves on the bottom

Limescale in the water circuit Descale as described in section 11.7 Descale

The espresso coffee drips from the edges of the filter holder rather than the holes

The filter holder has been inserted incor- rectly or is dirty

Attach the filter holder correctly and rotate firmly as far as it will go

The espresso boiler gasket has lost elas- ticity or is dirty

Have the espresso boiler gasket replaced by Cus- tomer Services

The holes in the filter holder spouts are blocked

Clean the filter holder spout holes

The filter or the perforated filter is blocked

Clean as described in section 11.3 Cleaning the coffee filters

The filter holder cannot be at- tached to the appliance

Too much coffee has been placed in the filter

Use the measure supplied and make sure you are using the correct filter for the type of preparation

The coffee froth is too light (de- livered from the spout too fast)

The pre-ground coffee is not pressed down firmly enough

Press the pre-ground coffee more firmly

There is not enough pre-ground coffee Increase the quantity of pre-ground coffee

The pre-ground coffee is too coarse Use only pre-ground coffee for espresso coffee makers

The wrong type of pre-ground coffee is being used

Change the type of pre-ground coffee

The steam function is required Flashing light: the appliance is heating up to deliver steam Light on steadily: the appliance is ready to deliver steam

orange flashing

The appliance needs descaling Descale the appliance, the operation is

complete when the light goes off.

Steam dial open Flashing lights: close the steam dial

High boiler temperature Flashing lights: Cool as described in sec- tion 9. Cooling the boiler

22

The coffee froth is too dark (delivered from the spout too slowly)

The pre-ground coffee is pressed down too firmly

Press the coffee down less firmly

There is not enough pre-ground coffee Reduce the quantity of pre-ground coffee

The espresso boiler outlet is blocked Clean as described in section 11.4 Cleaning the boiler outlet

The filter or the perforated filter is blocked

Clean as described in section 11.3 Cleaning the coffee filters

The pre-ground coffee is too fine Use only pre-ground coffee for espresso coffee makers

The pre-ground coffee is too fine or damp Use pre-ground coffee for espresso coffee makers only and make sure it is not too damp

Limescale in the water circuit Descale as described in section 11.7 Descale

After delivering coffee, the filter remains attached to the boiler outlet

Insert the filter holder again, deliver coffee, then remove the filter holder

The appliance will not make

any drink and the ,

and lights flash for a few seconds

No water in the tank Fill the tank with water

The tank has been inserted incorrectly and the valves on the bottom are not open

Press the tank down lightly to open the valves on the bottom

The espresso boiler outlet is blocked Clean as described in section 11.4 Cleaning the boiler outlet

The filter is blocked Clean as described in section 11.3 Cleaning the coffee filters

Limescale in the water circuit Descale as described in section 11.7 Descale

The appliance does not func- tion and all the lights flash

Disconnect the appliance immediately and contact authorised Customer Services.

No milk froth is formed when making cappuccino

The ring is in the HOT MILK position Push the ring into the CAPPUCCINO position.

Milk not cold enough Always use milk at refrigerator temperature

Cappuccino maker dirty Clean as described in section 8. Cleaning the cap- puccino maker after use

Limescale in the water circuit Descale as des

Manualsnet FAQs

If you want to find out how the EC685.BK DeLonghi works, you can view and download the DeLonghi EC685 BK Instruction Manual v2 on the Manualsnet website.

Yes, we have the Instruction Manual for DeLonghi EC685.BK as well as other DeLonghi manuals. All you need to do is to use our search bar and find the user manual that you are looking for.

The Instruction Manual should include all the details that are needed to use a DeLonghi EC685.BK. Full manuals and user guide PDFs can be downloaded from Manualsnet.com.

The best way to navigate the DeLonghi EC685 BK Instruction Manual v2 is by checking the Table of Contents at the top of the page where available. This allows you to navigate a manual by jumping to the section you are looking for.

This DeLonghi EC685 BK Instruction Manual v2 consists of sections like Table of Contents, to name a few. For easier navigation, use the Table of Contents in the upper left corner.

You can download DeLonghi EC685 BK Instruction Manual v2 free of charge simply by clicking the “download” button in the upper right corner of any manuals page. This feature allows you to download any manual in a couple of seconds and is generally in PDF format. You can also save a manual for later by adding it to your saved documents in the user profile.

To be able to print DeLonghi EC685 BK Instruction Manual v2, simply download the document to your computer. Once downloaded, open the PDF file and print the DeLonghi EC685 BK Instruction Manual v2 as you would any other document. This can usually be achieved by clicking on “File” and then “Print” from the menu bar.