Contents

Dell Wyse 3030 Thin Client USB Imaging Tool User Guide PDF

1 of 31
1 of 31

Summary of Content for Dell Wyse 3030 Thin Client USB Imaging Tool User Guide PDF

Dell Wyse USB Imaging Tool Version 3.1.0 Users Guide

June 2018 Rev. A01

Notes, cautions, and warnings

NOTE: A NOTE indicates important information that helps you make better use of your product.

CAUTION: A CAUTION indicates either potential damage to hardware or loss of data and tells you how to avoid

the problem.

WARNING: A WARNING indicates a potential for property damage, personal injury, or death.

2018 Dell Inc. or its subsidiaries. All rights reserved. Dell, EMC, and other trademarks are trademarks of Dell Inc. or its subsidiaries. Other trademarks may be trademarks of their respective owners.

Chapter 1: Introduction................................................................................................................. 4 What is new in this release................................................................................................................................................4 Key features..........................................................................................................................................................................4 Support matrix..................................................................................................................................................................... 5

Technical support.......................................................................................................................................................... 8

Chapter 2: Installing Dell Wyse USB Imaging Tool......................................................................... 9 Supported operating systems for Dell Wyse USB Imaging Tool installation......................................................... 9 Downloading Dell Wyse USB Imaging Tool....................................................................................................................9 Installing Dell Wyse USB Imaging Tool........................................................................................................................... 9 Uninstalling Dell Wyse USB Imaging Tool.....................................................................................................................10

Chapter 3: Using Dell Wyse USB Imaging Tool.............................................................................. 11 Boot details for supported devices................................................................................................................................12 Performing an image pull operation............................................................................................................................... 13

Configuring USB drive for pull operation................................................................................................................13 Pulling an image from a source device....................................................................................................................14

Performing an image push operation............................................................................................................................ 18 Configuring the USB drive for local image push operation................................................................................ 18 Pushing a local image to a target device...............................................................................................................20 Configuring the USB drive for network image push operation........................................................................ 23 Pushing a network image to a target device........................................................................................................ 25

Cloning a USB drive.......................................................................................................................................................... 27 Configuring USB Imaging Tool settings....................................................................................................................... 29

Appendix A: Troubleshooting.......................................................................................................30 Boot issues on USB drives.............................................................................................................................................. 30 Partition issues on SanDisk Cruiser flash drives........................................................................................................30 USB drive less than 1 GB error message..................................................................................................................... 30 USB drive not found......................................................................................................................................................... 30 Failed to format USB drive error message.................................................................................................................. 31

Contents

Contents 3

Introduction Dell Wyse USB Imaging Tool version 3.1.0 provides a simple USB imaging solution to help IT administrators to easily perform the pull or push operations in thin clients by using USB drives.

Dell Wyse USB Imaging Tool helps to quickly and easily image or reimage the supported Dell Wyse thin clients. The tool enables you to configure a bootable USB drive that you can plug into a thin client or a mobile thin client to pull or push the operating system images.

What is new in this release

The following are the new features in this release: Added support for ThinLinux version 2.0 on Wyse 3040 thin client. Added support for ThinLinux version 2.0 on Wyse 5070 thin client with Celeron processor. Added support for ThinLinux version 2.0 on Wyse 5070 thin client with Pentium processor. Added support for ThinLinux version 2.0 on Wyse 5070 Extended thin client. Added support for ThinOS version 8.5.1 on Wyse 5070 thin client with Celeron processor. Added support for ThinOS version 8.5.1 on Wyse 5070 thin client with Pentium processor. Added support for ThinOS version 8.5.1 on Wyse 5070 Extended thin client. Added support for Windows 10 IoT Enterprise (64-bit) on Wyse 5070 thin client with Celeron processor. Added support for Windows 10 IoT Enterprise (64-bit) on Wyse 5070 thin client with Pentium processor. Added support for Windows 10 IoT Enterprise (64-bit) on Wyse 5070 Extended thin client.

Key features USB Imaging Tool has the following key features: Provision to push an image from a network.

A simple and friendly user interface that enables you to perform the various operations with ease.

All the available USB disks and drives connected to the thin client devices are listed.

Provision to configure a USB drive to copy or pull the operating system image from the source thin client devices. Only OS and only BIOS (which includes CMOS) can be pulled separately.

Provision to configure a USB drive to update or push an operating system image to target thin client devices. Image push operation can be performed for only OS and only BIOS (which includes CMOS). A single USB key can store multiple images of different platforms.

Provision to clone an already configured USB drive containing the image that you want to push to target devices. Cloning helps to simultaneously update the operating system on multiple thin client devices.

Administrators can easily configure the backup path and back up the data present in the USB key during configuration. After the device is configured, the imaging tool seamlessly restores the data back to the USB key.

Support for 32bit and 64bit architecture based operating system platforms. Provision to configure different types of Dell Wyse thin clients.

Support for both removable and fixed type USB keys/Hard Disk Drives (HDDs).

1

4 Introduction

Support matrix The following table gives the list of embedded OS and the corresponding Dell Wyse thin clients that are supported by Dell Wyse USB Imaging Tool version 3.1.0.

Supported OS and thin clients

NOTE: For the thin clients, both Wyse and corresponding Dell names are mentioned in the following table under the Dell

Wyse Thin Clients heading. The first part of the name represents the legacy Wyse name and the second part after the em

dash represents the Dell marketing name. For example, in D90D7Wyse 5010 thin client with WES7, D90D7 represents

the Wyse Legacy name and Wyse 5010 thin client with WES7 represents the Dell marketing name.

Table 1. Operating systems and Dell Wyse thin clients

Operating Systems Dell Wyse Thin Clients

Microsoft Windows Embedded Standard 7 (WES7) 3290Wyse 3030 thin client

D90D7Wyse 5010 thin client with WES7 D90Q7Wyse 5020 thin client with WES7

Z90D7Wyse 7010 thin client with WES7

Z90DE7Wyse 7010 Extended Chassis thin client with WES7

Z90Q7Wyse 7020 thin client with WES7

Microsoft Windows Embedded Standard 7P (WES7P) D90D7P

D90Q7PWyse 5020 thin client with WES7P

Wyse 5060 thin client with WES7P

Z90D7P

Z90DE7P

Z90Q7PWyse 7020 thin client with WES7P

Z90QQ7PWyse 7020 Quad Display thin client with WES7P

Wyse 7040 thin client with WES7P

Latitude 3460 mobile thin client Latitude E7270 mobile thin client

Microsoft Windows Embedded 8 Standard (64-bit) (WE8S) D90D8Wyse 5010 thin client with WE8S D90Q8Wyse 5020 thin client with WE8S

Z90D8Wyse 7010 thin client with WE8S

Z90Q8Wyse 7020 thin client with WE8S

Windows 10 IoT Enterprise D90Q10Wyse 5020 thin client with Win10 IoT

Wyse 5060 thin client with Win10 IoT

Wyse 5070 thin client with Win10 IoT (Celeron and Pentium processor)

Wyse 5070 Extended thin client with Win10 IoT Z90Q10Wyse 7020 thin client with Win10 IoT Z90QQ10Wyse 7020 Quad Display thin client with Win10

IoT

Introduction 5

Table 1. Operating systems and Dell Wyse thin clients (continued)

Operating Systems Dell Wyse Thin Clients

Wyse 7040 thin client with Win10 IoT Latitude 3480 mobile thin client Latitude 5280 mobile thin client

Wyse Enhanced SUSE Linux Enterprise v7 D50DWyse 5010 thin client with Linux

D50QWyse 5020 thin client with Linux

Z50DWyse 7010 thin client with Linux

Z50QWyse 7020 thin client with Linux

Z50QQWyse 7020 Quad Display thin client with Linux

Wyse ThinOS Wyse 3030 LT thin client with ThinOS

Wyse 3040 thin client with ThinOS

D10DWyse 5010 thin client with ThinOS

D10DPWyse 5010 thin client with PCoIP

Wyse 5060 thin client with ThinOS

Wyse 5070 thin client with ThinOS (Celeron and Pentium processor)

Wyse 5070 Extended thin client with ThinOS

Wyse ThinOS Lite D00DXWyse 5010 zero client for Citrix

Wyse ThinLinux Wyse 3030 LT thin client with ThinLinux

Wyse 3040 thin client with ThinLinux

Wyse 3040 thin client with ThinLinux version 2.0 Wyse 5020 thin client with ThinLinux

Wyse 5060 thin client with ThinLinux

Wyse 5070 thin client with ThinLinux version 2.0 (Celeron and Pentium processor)

Wyse 5070 Extended thin client with ThinLinux version 2.0 Wyse 7020 thin client with ThinLinux

NOTE: End-of-Life (EOL) platforms are not supported in USB Imaging Tool version 3.1.0. Existing customers must use USB

Imaging Tool version 2.1.4 and earlier versions.

Supported types of USB drives

Dell Wyse USB Imaging tool version 3.1.0 enables you to configure the following types of USB drives: USB drive less than 32 GB of disk space, removable type USB drive higher than 32 GB of disk space, removable type

USB drive higher than 32 GB of disk space, fixed type

USB hard drive (HDD) greater than 32 GB of disk space, fixed type

NOTE:

For removable type USB drives higher than 32 GB of disk space, the following two partitions are created:

32 GB usable space, which is partitioned for OS image.

6 Introduction

Remaining disk space displayed as Raw or Unused when viewed by using disk management tool

For fixed type USB drives higher than 32 GB of disk space, the entire drive can be formatted and is usable.

A single USB drive cannot be used to store all the images (32bit, and 64bit). The drive can have only one type of

architecture either 32bit or 64bit.

USB Imaging Tool supports both FAT32 and NTFS file systems.

USB Imaging Tool supports fixed USB drives up to 1 TB of disk space.

Supported USB drives

The following USB drives are successfully validated with Dell Wyse USB Imaging tool version 3.1.0:

Table 2. Supported USB drives

USB Key Size Version Type

Kingston DT G4 - Security Key 8 GB 3 Removable

Kingston Data Traveler G4 16 GB 3 Removable

Kingston DT G4 16 GB 3 Removable

Kingston Data Traveler 106 32 GB 2 Removable

Kingston DT microDuo 3C C- type

32 GB 3 Removable

Kingston Data Traveler G4 64 GB 3 Removable

Kingston Data Traveler SE9 64 GB 2 Removable

Kingston Data Traveler G4 64 GB 3 Removable

Kingston DT SE9 64 GB 2 Removable

Kingston Data Traveler 101 G2 128 GB 2 Removable

SanDisk Ultra 32 GB 3 Removable

SanDisk Ultra Micro C-type 32 GB 3 Removable

SanDisk Ultra 64 GB 3 Removable

Sandisk Extreme 32 GB 3 Removable

Sandisk Extreme 64 GB 3 Removable

Sandisk Extreme 64 GB 3 Fixed

Sandisk Extreme Pro 128 GB 3 Removable

Sandisk Cruzer Blade 64 GB 2 Fixed

Seagate Expansion 500 GB 3 Fixed

Seagate Expansion 1 TB 3 Fixed

Toshiba 1 TB 3 Fixed

Transcend 16 GB 2 Removable

Introduction 7

Table 2. Supported USB drives (continued)

USB Key Size Version Type

Transcend 64 GB 2 Removable

Transcend 64 GB 3 Removable

Transcend JetFlash 128 GB 3 Removable

NOTE: USB drives from other manufacturers are not validated with USB Imaging Tool, and hence the supported USB drives

are recommended.

Technical support

To access technical resources self-service portal, knowledge base articles, software downloads, registration, warranty extensions/ RMAs, reference manuals, contact information, and so on, visit www.dell.com/wyse/support.

8 Introduction

Installing Dell Wyse USB Imaging Tool You can install Dell Wyse USB Imaging tool version 3.1.0 on any thin client device that meets the operating system and disk space requirements.

Supported operating systems for USB Imaging Tool installation

Downloading USB imaging tool

Installing USB imaging tool

Uninstalling USB imaging tool

Supported operating systems for Dell Wyse USB Imaging Tool installation The following are the supported operating systems: Windows Server 2008 R2 Enterprise SP1

Windows 7 Enterprise SP1 (32bit and 64bit)

Windows 7 Ultimate SP1 (32bit and 64bit)

Windows 8.1 Enterprise (32bit and 64bit)

Windows 10 Enterprise Build 1511 (32bit and 64bit)

Windows 10 Enterprise Build 1607 (32bit and 64bit)

Downloading Dell Wyse USB Imaging Tool USB Imaging Tool is available on the Dell Support site.

Steps

1. Open a web browser and go to www.downloads.dell.com/wyse/USBFT/.

2. Click the directory path that displays the latest version of USB Imaging tool. The download link for USB Imaging tool software along with relevant pdf files such as Release Notes and Users Guide are displayed on the web page.

3. Click the download link (.exe file) for USB Imaging tool and navigate to the location where you want to save the self-extracting .exe file that contains USB Imaging Tool installer. The file is downloaded in the location you have specified.

Installing Dell Wyse USB Imaging Tool

Prerequisites

A minimum free disk space of 2 GB to download, extract, and install USB Imaging Tool. Microsoft .Net Framework 3.5 installed.

NOTE: If you are installing USB Imaging Tool version 3.1.0 on a thin client device, ensure that you disable the File-Based

Write Filter (FBWF) on the device.

2

Installing Dell Wyse USB Imaging Tool 9

Steps

1. Log in as Administrator in to the system where you want to run the installation and extract the contents of the Dell Wyse USB Imaging Tool installer.

2. Navigate to the folder where you have extracted the installer and run Dell Wyse USB Imaging Tool.exe. The Welcome screen is displayed.

3. Click the Dell Application software EULA link to read the license agreements.

4. Click Next. The default installation path is displayed.

5. Click Change if you want to specify a custom installation path, and click Next after you specify the path.

6. Click Next to start the installation process.

7. Click Exit to close the installer window.

Uninstalling Dell Wyse USB Imaging Tool

Steps

1. Go to Control Panel, and click Programs and Features.

2. From the programs list, select Dell Wyse USB Imaging Tool.

3. Click Uninstall. The Dell Wyse USB Imaging Tool Uninstallation screen is displayed.

4. Click Next. After the uninstallation is complete, the Uninstallation Complete message is displayed.

5. Click EXIT to close the Uninstaller window.

NOTE: You can also re-run the Dell Wyse USB Imaging Tool.exe file on your thin client to uninstall USB

Imaging tool.

10 Installing Dell Wyse USB Imaging Tool

Using Dell Wyse USB Imaging Tool Dell Wyse USB Imaging Tool enables you to prepare USB keys to perform various operations on source and target thin client devices. The tasks that you can perform are:

Image PullEnables you to prepare the USB key to pull an operating system image or BIOS configuration including CMOS settings from a source device

Image PushEnables you to prepare the USB key to push an operating system image or BIOS configuration to a target device.

The Image Push tab allows you to either push a local image or a network image to the target device.

Clone USBEnables you to create a copy of a configured USB key that is configured for the pull or push operation.

Configure Backup PathEnables you to set the backup path to back up the contents of a USB key.

After you plug a USB drive to the thin client and start Dell Wyse USB Imaging Tool, the following screen is displayed. The number of USB drives that are connected to your thin client are displayed on the Home screen.

The following USB drive attributes are displayed: Used Space Free Space Total Space

Figure 1. Home screen

To view the USB drives, click USB Drives in the left pane.

3

Using Dell Wyse USB Imaging Tool 11

Figure 2. Available USB drives

Boot details for supported devices The following table provides the guidelines for configuring the boot options on the supported thin client devices:

Table 3. Supported thin client devices and corresponding boot guidelines

Supported thin client devices Boot guidelines

Wyse 5010 zero client for Citrix (D00DX/Xenith Pro 2), Wyse 5010 thin client with Linux (D50D), Wyse 7010 thin client with Linux (Z50D), Wyse 7010 thin client with WES7 (Z90D7), Wyse 7010 Extended Chassis thin client with WES7 (Z90DE7), Z90D8, Wyse 3030 thin client (3290), Wyse 7020 thin client with WES7 (Z90Q7), Z90D7P, Z90DE7P, Wyse 7020 thin client with WES7P (Z90Q7P), Wyse 7020 accelerated graphics thin client with WES7P (Z90QQ7P), Wyse 7020 thin client with Win10 IoT (Z90Q10), Wyse 7020 Quad Display thin client with Win10 IoT (Z90QQ10), Wyse 7020 thin client with Linux (Z50Q), Wyse 7020 Quad Display thin client with Linux (Z50QQ), Wyse 7020 thin client with ThinLinux, and Z90Q8.

To enter and use the one-time boot menu: 1. Plug in the configured USB drive to the thin client.

2. During boot, keep pressing the P key until the Boot menu appears.

3. Select the USB HDD option displaying your USB drive vendor name and press Enter.

4. Follow the steps displayed on the screen.

Wyse 3030 LT thin client with ThinOS, and ThinLinux, Wyse 5010 thin client with WES7 (D90D7), Wyse 5020 thin client with WES7P (D90Q7P), D90D8, D90Q8, Wyse 5020 thin client with WES7 (D90Q7), D90D7P, Wyse 5020 thin client with Win10 IoT (D90Q10), Wyse 5020 thin client with Linux (D50Q), Wyse 5010 thin client with ThinOS (D10D), Wyse 5010 thin client with PCoIP (D10DP), Wyse 5020 thin client with ThinLinux, and Wyse 5060 thin client with WES7P, ThinOS, ThinLinux and Win10 IoT.

If the Boot from USB option is already enabled, you can enter and use the one-time boot menu: 1. Plug in the configured USB drive to the thin client.

2. During boot, keep pressing the P key until the Boot menu appears.

3. Select the Boot from USB option and press Enter.

4. Follow the steps displayed on the screen.

12 Using Dell Wyse USB Imaging Tool

Table 3. Supported thin client devices and corresponding boot guidelines (continued)

Supported thin client devices Boot guidelines

Wyse 3040 thin client with ThinOS, and ThinLinux, Wyse 7040 thin client with WES7P, Latitude 3460 mobile thin client with WES7P, Latitude E7270 mobile thin client with WES7P, Latitude 3480 mobile thin client with Win10 IoT, Latitude 5280 mobile thin client with Win10 IoT, Wyse 5070 thin client with ThinOS, Win10 IoT, and ThinLinux 2.0, Wyse 5070 Extended thin client with ThinOS, Win10 IoT, and ThinLinux 2.0.

To enter and use the boot menu: 1. Plug in the configured USB drive to the thin client. 2. During boot, keep pressing the F12 key until the Boot

menu appears.

3. Select the UEFI option displaying your USB drive vendor name and press Enter.

4. Follow the steps displayed on the screen.

Performing an image pull operation An image pull operation consists of two parts. In the first part, you configure the USB drive for the pull operation by using USB Imaging Tool. In the second part, you plug in the USB drive to a source device and perform the pull operation.

NOTE: When you prepare the USB drive for a pull operation, the USB drive is also configured for a push operation. You can

use the same drive for a pull or push operation. However, if you use the same key for the push operation, ensure that the

images you want to push are copied to the USB drive.

For more information, see

Configuring USB drive for pull operation.

Pulling an image from a source device.

Configuring USB drive for pull operation

Steps

1. Start USB Imaging Tool. The tool displays the Image Pull screen by default.

Using Dell Wyse USB Imaging Tool 13

Figure 3. Image Pull

2. Plug in the USB drive to the system running the USB Imaging Tool.

3. Click the Refresh button to populate the USB drives.

NOTE: You can have multiple USB drives plugged to your system.

4. Select the USB drive from the Available drives drop-down list.

5. Select the operating system architecture that you want to pull from the source device, and then select one of the following: 32 bitSelect this option to copy or pull the 32bit architecture based OS from the source device. 64 bitSelect this option to copy the 64bit architecture based OS from the source device.

6. Select the components that you want to pull from the source thin client device.

You can select either one or both of the following options:

Operating SystemSelect this option to pull the operating system image from the source device. BIOS (Includes CMOS)Select this option to pull only the BIOS and CMOS configuration from the source device.

7. To configure the USB drive, select the Preferences option.

You can select either one or both of the following options:

Compress imageSelect this option to pull the image from the source device in a compressed format. Preserve USB Drive contentsSelect this option to preserve all the data present in the USB drive before configuring

it for an image pull operation.

8. Click Configure USB Drive. The USB drive is formatted, and the status is displayed in the progress bar.

Results

USB Imaging Tool formats the USB drive, copies the necessary files based on the selected OS architecture, and completes the configuration of USB drive for the image pull operation.

Pulling an image from a source device

Prerequisites

Before you begin the pull operation, ensure that your device is configured to boot from the USB drive.

14 Using Dell Wyse USB Imaging Tool

Steps

1. Plug in the USB drive to the supported source device.

2. To access the boot menu, reboot the device, and keep pressing either P key or F12 key during system reboot depending on your thin client model; To choose the boot menu function key (P or F12) for your thin client model, see Boot details for supported devices. The boot options are displayed, and you can see either of the following boot menu screens depending on your thin client model:

Figure 4. Boot Menu

Using Dell Wyse USB Imaging Tool 15

Figure 5. Boot Menu

3. Select the USB option displaying your USB drive vendor name, and press Enter. The device reboots from the USB drive, and the following screen is displayed:

Figure 6. Pulling the image to the USB drive

In the left pane, the following information is displayed: Device infoDevice info displays information such as platform, media, and the system of the source device. USB driveUSB drive displays information such as used space, free space, and total space of the USB drive.

4. Click the icon.

If the source device runs an operating system other than ThinLinux 2.0, go to step 6.

The Pulling device image to USB drive screen is displayed.

16 Using Dell Wyse USB Imaging Tool

Figure 7. Pulling the image to the USB drive

5. If the source device runs ThinLinux 2.0 operating system, select one of the following options:

Boot + Recovery + OS Boot + Recovery (Recommended) Boot + OS

Figure 8. Pulling the ThinLinux 2.0 image to the USB drive

6. Click OK. The image pull operation starts, and the overall status is displayed in the progress bar.

Using Dell Wyse USB Imaging Tool 17

Figure 9. Copying the image to USB key

NOTE: The pull operation pulls the operating system image, or the BIOS configuration, or both depending on the options

you have selected in the Image Pull screen of USB Imaging Tool. If you have selected the Compress Image option,

then the image is pulled in a compressed format.

7. After the pull operation is complete, remove the USB drive from the source device.

8. To reboot the device, click Restart.

Performing an image push operation Similar to the image pull operation, the image push operation also consists of two parts. In the first part you prepare the USB drive to perform an image push operation. In the second part you push the OS or BIOS images on to the target devices. You can add multiple images on a single USB drive.

You can perform the push operation in two ways: Local image push

Configuring USB drive for local image push operation Pushing local image to a target device

Network image push Configuring USB drive for network image push operation Pushing network image to a target device

Configuring the USB drive for local image push operation

Steps

1. Start USB Imaging Tool. The tool displays the Image Pull screen by default.

2. Click Image Push to display the Image Push screen.

18 Using Dell Wyse USB Imaging Tool

Figure 10. Image push

3. Plug in the USB drive to the system running USB Imaging Tool.

4. Select the USB drive from the Available drives drop-down list. If your USB drive already contains images, the images are displayed on the screen.

5. Select the OS architecture that you want to push to the target device. Select one of the following: 32 bitSelect this option to push the 32-bit architecture based OS to the target device. 64 bitSelect this option to push the 64-bit architecture based OS to the target device.

6. To add a new local image on the USB drive, do the following:

Option Description

Add a new Image on the USB drive

Perform the following steps: a. Click the Local tab. b. To add an image from a different location, click the + icon. c. Navigate to the location where you have saved the image files. d. Select the .rsp file from the image folder. You can also select the Command XML file. For this,

select the Command XML option from the drop-down against File Name, and navigate to the commands XML file location. This file is located under a sub-folder that has the same name as the OS image folder.

e. Click OK to add the image to the table. The image is displayed in the table.

Delete existing Images on the USB drive

To delete the existing images, click the Delete icon on the images displayed in the table. The images are deleted from the table but are only marked for deletion in the USB drive.

You can view the OS and BIOS check boxes selected or cleared as per the contents of the image files you have chosen. For example, if the image file contains only the BIOS configuration, only the BIOS check box is selected for that image.

If both the OS and BIOS check boxes are selected and you clear one of the check boxes, then that image component is not added on the USB drive.

NOTE:

Using Dell Wyse USB Imaging Tool 19

In a single session, you cannot configure the local image and network image path simultaneously.

You cannot add the same network image path with different file transfer protocols, such as FTP, HTTP, HTTPS, or

CIFS.

You cannot add the same operating system imageeither local or networkwith both .rsp and .xml files.

On the Image Push screen, the information entered in the local image fields are retained when you switch to the

Network tab.

On the Image Push screen, the information entered in the network image fields are retained when you switch to the

Local tab.

On the Image Push screen, the information entered in the local and network image fields are not retained when you

switch to Image Pull, Image Push, Clone, or Settings tabs.

7. Click Configure USB Drive.

8. Select one of the following options:

Update (Recommended)Select this option to add or delete images from an existing configured USB drive. Format and UpdateSelect this option if your USB drive is corrupted or not configured. This option enables you to

back up contents, initialize the drive, and add or delete the selected image.

The status is displayed in the progress bar.

Pushing a local image to a target device

Prerequisites

Before you begin the pull operation, ensure that your device is configured to boot from the USB drive.

Steps

1. Plug in the USB drive to the supported source device.

2. To access the boot menu, reboot the device, and keep pressing either the P key or F12 key during system reboot depending on your thin client model; To select the boot menu function key (P or F12) for your thin client model, see Boot details for supported devices.

The boot options are displayed, and you can see either of the following boot menu screens depending on your thin client model:

20 Using Dell Wyse USB Imaging Tool

Figure 11. Boot menu

Figure 12. Boot menu

3. Select the USB option displaying your USB drive vendor name and press Enter.

The device reboots from the USB drive, and the image that needs to be pushed to the device is displayed.

Using Dell Wyse USB Imaging Tool 21

Figure 13. Local Image push

In the left pane, the following information is displayed: Device infoDisplays information such as platform, media, and system of the target device. USB driveDisplays information such as used space, free space, and total space of the USB drive.

4. In the Choose image to push to this device section, select the local image from the list, and click OK.

The image push operation starts, and the overall status is displayed in the progress bar.

Figure 14. Operating Systems (In Progress)

5. After both operating system and BIOS push operations are complete, remove the USB drive from the target device.

6. To reboot the device, click Restart.

22 Using Dell Wyse USB Imaging Tool

NOTE: Wyse 5060 thin client and Wyse 3030 LT thin client restart automatically after BIOS push operation is complete.

Configuring the USB drive for network image push operation

Steps

1. Start USB Imaging Tool. The tool displays the Image Pull screen by default.

2. Click Image Push to view the Image Push screen.

Figure 15. Network image push

3. Plug in the USB drive to the system running USB Imaging Tool.

4. Select the USB drive from the drop-down list. If your USB drive contains other images, the screen displays the images in the table.

5. Select the operating system architecture that you want to push to the target device. Select one of the following: 32 bitSelect this option to push the 32-bit architecture based operating system to the target device. 64 bitSelect this option to push the 64-bit architecture based operating system to the target device.

6. To add an image to the USB drive, perform the following steps:

Option Description

Add a new Image on the USB drive

Perform the following steps: a. Click the Network tab. b. Click the + icon. c. Enter the URL where the image files are present.

NOTE: Before configuring the USB drive for network image Push, ensure that you check

the reachability and accessibility of the URL which you enter.

d. Enter the username and password. e. Click Add to create an image push entry in the table.

Using Dell Wyse USB Imaging Tool 23

Option Description

Delete existing image path on the USB drive

To delete the existing image path, click the Delete icon on the image path entry displayed in the table. The image path entries are deleted from the table but are only marked for deletion in the USB drive.

NOTE:

In a single session, you cannot configure the local image and network image path simultaneously.

You cannot add the same network image path with different file transfer protocols, such as FTP, HTTP, HTTPS, or

CIFS.

You cannot add the same operating system imageeither local or networkwith both .rsp and .xml files.

On the Image Push screen, the information entered in the local image fields are retained when you switch to the

Network tab.

On the Image Push screen, the information entered in the network image fields are retained when you switch to the

Local tab.

On the Image Push screen, the information entered in the local and network image fields are not retained when you

switch to Image Pull, Image Push, Clone, or Settings tabs.

7. Click Configure USB Drive.

8. Select any one of the following options:

Update (Recommended)Select this option to add or delete images to an existing configured USB drive. Format and UpdateSelect this option if your USB drive is corrupted or not configured. This option backs up contents,

initialize the drive, and add or delete the selected image.

The status is displayed in the progress bar.

Figure 16. Pushing image to the device

USB Imaging Tool formats the USB drive, copies the necessary files based on the selected OS architecture, and completes the configuration of USB drive for the image pull operation.

24 Using Dell Wyse USB Imaging Tool

Pushing a network image to a target device

Prerequisites

Before you begin the push operation, do the following: NOTE:

Ensure that your device is configured to boot from the USB drive.

Before pushing the operating system image from the network location, ensure that the network location is reachable and

accessible from the subnet/network where your thin client is connected.

Steps

1. Plug in the USB drive to the supported source device.

2. To access the boot menu, reboot the device, and keep pressing either the P key or F12 key during system reboot depending on your thin client model; To choose the boot menu function key (P or F12) for your thin client model, see Boot details for supported devices.

The boot options are displayed, and you can see either of the following boot menu screens depending on your thin client model.

Figure 17. Boot menu

Using Dell Wyse USB Imaging Tool 25

Figure 18. Boot menu

3. Select the USB option displaying your USB drive vendor name and press Enter.

The device reboots from the USB drive, and the screen with the network image that you want to push to the device is displayed.

Figure 19. Network image push operation

4. In the Choose image to push to this device section, select the network image and click OK.

The network image push operation starts, and the overall status is displayed in the progress bar.

26 Using Dell Wyse USB Imaging Tool

Figure 20. Operating System (In Progress)

5. After both operating system and BIOS push operations are complete, remove the USB drive from the target device.

6. To reboot the device, click Restart.

Cloning a USB drive You can clone or duplicate a configured USB drive that is currently ready to push an image. Clone operation can be performed only when you have a configured USB drive for a push operation or you have a valid image. You can create as many clones or duplicates as you need to simultaneously perform the push operation on multiple devices at the same time.

Prerequisites

Ensure that the source and target USB drives contain the same disk space, or the target contains more disk space than the source.

Steps

1. Plug in a USB drive that is configured for a push operation to the system running USB Imaging Tool.

2. Plug in another USB drive for which you want to replicate the source USB drive.

3. Start USB Imaging Tool and click Image Clone. The Image Clone page is displayed.

4. From the Available drive drop-down list, select the configured USB drive. LocalThe local images stored in the source USB drive are displayed in the table.

Using Dell Wyse USB Imaging Tool 27

Figure 21. Local image clone NetworkThe network images stored in the source USB drive are displayed in the table.

Figure 22. Network image clone

5. Select the target USB drive from the Destination USB Drive drop-down list.

6. Click Configure USB Drive.

28 Using Dell Wyse USB Imaging Tool

USB Imaging Tool formats the destination USB drive, and then copies the necessary boot loader files based on the OS architecture configured in the source drive. The tool copies the OS Images from the source drive to destination drive.

The overall progress is displayed on the progress bar.

Configuring USB Imaging Tool settings The Settings page enables you to set the backup path to back up the contents of a USB drive.

Steps

1. In the left pane, click the Settings tab. The Settings page is displayed. This page allows you to change the configurable USB Imaging Tool settings.

Figure 23. Settings

2. To change the location for your backup files, click Change.

3. To view the log files stored on the thin client, click the Open Logs link.

Using Dell Wyse USB Imaging Tool 29

Troubleshooting When you perform the pull or push operations on thin client devices, you may experience problems with the USB keys. This section describes some basic troubleshooting that you can implement when you experience any problems.

Boot issues on USB drives If you experience problems booting from a configured USB drive, Dell recommends that you try a different brand of USB drive. For a list of USB drives that are successfully tested with USB Imaging Tool, see Support matrix.

Partition issues on SanDisk Cruiser flash drives SanDisk Cruiser Flash Drives come with support for U3. For more information on U3, see www.sandisk.com. When you use these drives, you must select the drive usage from one of the following options: Apps and Storage

Storage

If you select Apps and Storage, the drive creates two partitionsCD and Read-only. This partition sometimes prevents USB Imaging Tool to properly prepare the USB drive for a pull or push operation. To resolve this problem, you can do one of the following: Go to www.sandisk.com, click the Support tab, search in the SanDisk Knowledge Base for document 2550, and then follow

the instructions in the documentation.

Go to www.sandisk.com, and do the following: 1. Click the Support tab.

2. From the BROWSE A PRODUCT CATEGORY list, select Flash Drives.

3. Type U3 Launchpad Remover in the search bar, and click Search All Answers.

4. Click the U3 Launchpad Remover documentation and follow the instructions.

USB drive less than 1 GB error message

About this task

When you are configuring a USB key for a pull or push operation, the following error message is displayed:

USB drive size is less than 1GB, please insert a higher capacity drive.

Dell recommends not to use USB drives with less than 1 GB of disk space.

USB drive not found The USB HDDs go offline after multiple pull or push configurations of the USB HDDs.

To bring the disk to online state, do the following: 1. Go to Disk Management. 2. Select the USB HDDs that are in offline state. 3. Right-click each USB HDD in offline state and select Online.

The USB HDDs are accessible.

A

30 Troubleshooting

Failed to format USB drive error message When you are configuring the USB drive for image pull or push operation, either of the following error messages may be displayed:

Failed to format USB drive. Invalid Partitions. Please check logs Failed to finalize the USB Drive

Workaround: Close the USB Imaging tool application, format the USB drive by using Diskpart or Windows Disk management tool, and then use the USB drive for image push or pull operation.

Troubleshooting 31

Manualsnet FAQs

If you want to find out how the Wyse 3030 Dell works, you can view and download the Dell Wyse 3030 Thin Client USB Imaging Tool User Guide on the Manualsnet website.

Yes, we have the USB Imaging Tool User Guide for Dell Wyse 3030 as well as other Dell manuals. All you need to do is to use our search bar and find the user manual that you are looking for.

The USB Imaging Tool User Guide should include all the details that are needed to use a Dell Wyse 3030. Full manuals and user guide PDFs can be downloaded from Manualsnet.com.

The best way to navigate the Dell Wyse 3030 Thin Client USB Imaging Tool User Guide is by checking the Table of Contents at the top of the page where available. This allows you to navigate a manual by jumping to the section you are looking for.

This Dell Wyse 3030 Thin Client USB Imaging Tool User Guide consists of sections like Table of Contents, to name a few. For easier navigation, use the Table of Contents in the upper left corner.

You can download Dell Wyse 3030 Thin Client USB Imaging Tool User Guide free of charge simply by clicking the “download” button in the upper right corner of any manuals page. This feature allows you to download any manual in a couple of seconds and is generally in PDF format. You can also save a manual for later by adding it to your saved documents in the user profile.

To be able to print Dell Wyse 3030 Thin Client USB Imaging Tool User Guide, simply download the document to your computer. Once downloaded, open the PDF file and print the Dell Wyse 3030 Thin Client USB Imaging Tool User Guide as you would any other document. This can usually be achieved by clicking on “File” and then “Print” from the menu bar.