Contents

Dell Wyse 3020 Thin Client Monitor Installation Guide PDF

1 of 13
1 of 13

Summary of Content for Dell Wyse 3020 Thin Client Monitor Installation Guide PDF

Monitor mount for 2017 P-series Dell monitors Installation guide

Notes, cautions, and warnings

NOTE: A NOTE indicates important information that helps you make better use of your product.

CAUTION: A CAUTION indicates either potential damage to hardware or loss of data and tells you how to avoid the problem.

WARNING: A WARNING indicates a potential for property damage, personal injury, or death.

2017 - 2019 Dell Inc. or its subsidiaries. All rights reserved. Dell, EMC, and other trademarks are trademarks of Dell Inc. or its subsidiaries. Other trademarks may be trademarks of their respective owners.

2019 - 02

Rev. A02

Contents

1 Supported clients and monitors......................................................................................................................4

2 Included in the tool kit................................................................................................................................... 5

3 Mounting Wyse 5010, Wyse 5020, and Wyse 5060 clients.............................................................................6

4 Mounting Wyse 3010, Wyse 3020, Wyse 3030, Wyse 3030LT, and Wyse 5030 clients.................................. 11

Contents 3

Supported clients and monitors The monitor mount for 2017 P-series monitors is designed to work with the following clients and monitors:

NOTE: The mount is designed to work with Dell monitors and clients listed in this section. The mount should not be used with other Dell or third party monitors or clients.

Supported clients are:

Dell Wyse 3010 (Tx0) thin client

Dell Wyse 3020 (Tx0D) thin client

Dell Wyse 3030 (N03D) thin client

Dell Wyse 3030LT (N06D) thin client

Dell Wyse 5010 (Dx0D) thin client

Dell Wyse 5020 (Dx0Q) thin client

Dell Wyse 5030 (PxN) PCoIP zero client

Dell Wyse 5060 (N07D) thin client

NOTE: Installation instructions for the Dell Wyse 3040 thin client is not covered in this document. Please go to www.dell.com/ support/manuals to find installation instructions for the Dell Wyse 3040 thin client.

Supported monitors are:

P1917S

P2017H

P2217H

P2317H

P2417H

P2717H

U2417H

U2718Q

P2219H

P2319H

P2419H

P2719H

1

4 Supported clients and monitors

Included in the tool kit The following parts are included in the tool kit:

1 One screw (M2.5x0.45)

2 Four screws (M4x0.7-6)

3 Four hexagonal nuts (M4x0.7)

4 One stopper

5 One power adapter holder

6 One monitor mount for P-series monitors

NOTE:

Dell Wyse 3040 requires wall mount 575BBMK with the P-series mount.

2

Included in the tool kit 5

Mounting Wyse 5010, Wyse 5020, and Wyse 5060 clients

Use the following instructions to attach the client to the P-series mount.

1 Preparing the clientUse a Phillips-head screwdriver to remove the four filler screws from the side of the client.

3

6 Mounting Wyse 5010, Wyse 5020, and Wyse 5060 clients

2 Attaching the clientInstall the thin client on the P-series mount with the M4.07-6 screws included in the tool kit.

NOTE: The power button should face outwards and air vents should be on top end for proper heat dissipation.

3 Attaching the power adapter holderSlide the small hooks downward into the vertical slotted holes and the large hooks onto the top edge of the mount. Use the M2.5x0.45 screw to secure the power adapter holder onto the mount as indicated in the following illustration.

4 Removing the monitor stand

a Place the monitor panel face down on a soft cloth or cushion.

b Remove the stand from the monitor by pushing the monitors quick release button as indicated in the following illustration.

Mounting Wyse 5010, Wyse 5020, and Wyse 5060 clients 7

5 Attaching P-series mount to the monitor

Remove the monitor screws from the back of the monitor, and use them when you proceed with installation later.

Position the P-series mount on the back of the monitor. Tilt and slide the top tabs into the dedicated tab slots, and then firmly slide down bottom edge of mount until it snaps in place.

Reinstall the monitor screws.

8 Mounting Wyse 5010, Wyse 5020, and Wyse 5060 clients

CAUTION: Do not over-tighten the screws.

6 Reinstalling the monitor standInsert the upper stand tabs into the dedicated space on the P-series mount and gently press down until the quick release button snaps into place. Place the monitor in the upright position.

7 Adjusting and securing monitor height (optional)

For portrait orientation-Raise the monitor to the maximum height and attach the stopper. Ensure that the arrow on the stopper is facing up and facing front side of the stand. Wrap the stopper around the stand and snap the ends.

For landscape orientation-Adjust the monitor height and attach stopper. Ensure that the arrow on the stopper is facing up and facing front side of the stand, and then snap the stopper ends.

Mounting Wyse 5010, Wyse 5020, and Wyse 5060 clients 9

NOTE:

The stopper is required for P-series monitors to hold the monitor in place at the desired height.

8 Connecting cablesTo complete the setup, make all the desired connections, and then plug in the power adapter to an electrical outlet.

10 Mounting Wyse 5010, Wyse 5020, and Wyse 5060 clients

Mounting Wyse 3010, Wyse 3020, Wyse 3030, Wyse 3030LT, and Wyse 5030 clients

Use the following instructions to mount the Wyse 3010, Wyse 3020, Wyse 3030, Wyse 3030LT, and Wyse 5030 clients to the P mount. These clients require mounting of the client to their respective horizontal stands before installing the thin client to the P-series monitor mount. Horizontal stands required by thin client model are:

Table 1. Client name and part number

Client name Part number

Wyse 3010 XXJ7P

Wyse 3020/5030 92GX5

Wyse 3030/3030LT GYTXN

1 Preparing the client and attaching the power adaptor

a If the thin client is installed on the horizontal stand, remove it from the stand. On the inside of the horizontal stand, slide one of the four hex nuts which come with the tool kit into one of the four screw holes.

b From outside of the horizontal stand, insert a shoulder screw into the hex nut and tighten it.

c Repeat for remaining three hex nuts and shoulder screws.

d Insert the client into the horizontal stand, with the power button facing upward, and the extended plastic ledge on the opposite side.

e To install the power adapter holder, slide the small hooks downward into the vertical slotted holes and the large hooks onto the top edge of the mount. Use the M2.5x0.45 screw to secure the power adapter holder onto the mount as indicated in the following illustration.

4

Mounting Wyse 3010, Wyse 3020, Wyse 3030, Wyse 3030LT, and Wyse 5030 clients 11

NOTE:

Slide the hex nut across the stand surface so that it easily slips into the recessed cut-out in the horizontal stand.

Use the plastic bracket with the hex holes.

2 Removing the monitor stand

a Place the monitor panel face down on a soft cloth or cushion.

b Remove the stand from the monitor by pushing the monitors quick release button as indicated in the following illustration.

3 Attaching P-series mount to the monitor

a Remove the monitor screws from the back of the monitor and use them when you proceed with installation later.

b Position the P-series mount on the back of the monitor. Tilt and slide the top tabs into the dedicated tab slots, and then firmly slide down bottom edge of mount until it snaps in place.

c Reinstall the monitor screws.

12 Mounting Wyse 3010, Wyse 3020, Wyse 3030, Wyse 3030LT, and Wyse 5030 clients

4 Reinstalling the monitor standInsert the upper stand tabs into the dedicated space on the P-series mount and gently press down until the quick release button snaps into place. Place the monitor in the upright position.

5 Adjusting and securing monitor height (optional)

a For portrait orientation-Raise the monitor to the maximum height and attach the stopper. Ensure that the arrow on the stopper is facing up and facing front side of the stand. Wrap the stopper around the stand and snap the ends.

b For landscape orientation-Adjust the monitor height and attach stopper. Ensure that the arrow on the stopper is facing up and facing front side of the stand, and then snap the stopper ends.

NOTE:

The stopper is required for P-series monitors to hold the monitor in place at the desired height.

If you

Manualsnet FAQs

If you want to find out how the Wyse 3020 Dell works, you can view and download the Dell Wyse 3020 Thin Client Monitor Installation Guide on the Manualsnet website.

Yes, we have the Monitor Installation Guide for Dell Wyse 3020 as well as other Dell manuals. All you need to do is to use our search bar and find the user manual that you are looking for.

The Monitor Installation Guide should include all the details that are needed to use a Dell Wyse 3020. Full manuals and user guide PDFs can be downloaded from Manualsnet.com.

The best way to navigate the Dell Wyse 3020 Thin Client Monitor Installation Guide is by checking the Table of Contents at the top of the page where available. This allows you to navigate a manual by jumping to the section you are looking for.

This Dell Wyse 3020 Thin Client Monitor Installation Guide consists of sections like Table of Contents, to name a few. For easier navigation, use the Table of Contents in the upper left corner.

You can download Dell Wyse 3020 Thin Client Monitor Installation Guide free of charge simply by clicking the “download” button in the upper right corner of any manuals page. This feature allows you to download any manual in a couple of seconds and is generally in PDF format. You can also save a manual for later by adding it to your saved documents in the user profile.

To be able to print Dell Wyse 3020 Thin Client Monitor Installation Guide, simply download the document to your computer. Once downloaded, open the PDF file and print the Dell Wyse 3020 Thin Client Monitor Installation Guide as you would any other document. This can usually be achieved by clicking on “File” and then “Print” from the menu bar.