Dell PowerEdge 500SC Server Microprocessor Upgrade Installation Guide PDF
Summary of Content for Dell PowerEdge 500SC Server Microprocessor Upgrade Installation Guide PDF
w w w. d e l l . c o m | s u p p o r t . d e l l . c o m
Dell Systems
Microprocessor Upgrade
Installation Guide
9D904et4.fm Page 1 Tuesday, October 1, 2002 11:56 PM
Notes, Notices, and Cautions NOTE: A NOTE indicates important information that helps you make better use of your computer.
NOTICE: A NOTICE indicates either potential damage to hardware or loss of data and tells you how to avoid the problem.
CAUTION: A CAUTION indicates a potential for property damage, personal injury,
or death.
Information in this document is subject to change without notice. 2002 Dell Computer Corporation. All rights reserved.
Reproduction in any manner whatsoever without the written permission of Dell Computer Corporation is strictly forbidden.
Trademarks used in this text: Dell and the DELL logo are trademarks of Dell Computer Corporation.
Other trademarks and trade names may be used in this document to refer to either the entities claiming the marks and names or their products. Dell Computer Corporation disclaims any proprietary interest in trademarks and trade names other than its own.
October 2002 P/N 9D904 Rev. A04
9D904et4.fm Page 2 Tuesday, October 1, 2002 11:56 PM
Microprocessor Upgrade Instal lat ion Guide 1-1
This document provides instructions about adding or replacing microprocessors. To take
advantage of future options in speed and functionality, you can add secondary
microprocessors or replace microprocessors in your system.
NOTICE: Before you add or replace a microprocessor, check the latest system BIOS
information on the Dell Support website at support.dell.com, and upgrade the BIOS if necessary.
Each microprocessor and its associated cache memory are contained in a pin-grid array
(PGA) package that is installed in a ZIF socket on the system board. The following
subsection describes how to install or replace the microprocessor in either the primary or
secondary microprocessor sockets.
NOTE: In a single microprocessor system, the microprocessor must be installed in the
primary microprocessor socket.
Adding or Replacing a Microprocessor NOTICE: The secondary microprocessors must be of the same type and speed as the primary
microprocessor. If the microprocessors are different speeds, they will operate at the speed of the
slower microprocessor.
In addition to the ZIF socket for the primary microprocessor on the system board, other
ZIF sockets might be present to accommodate secondary microprocessors.
The following items are included in the microprocessor upgrade kit:
A microprocessor
A heat sink
Heat-sink retention clip(s)
A VRM, used if adding a secondary microprocessor
Your upgrade kit may also include a cooling fan.
CAUTION: Before you perform this procedure, read the safety instructions in
your System Information document.
1 Turn off the system, including any peripherals, and disconnect the power cable from the electrical outlet.
2 Open the system doors, or remove the system cover (see your Installation and Troubleshooting Guide).
CAUTION: See "Protecting Against Electrostatic Discharge" in the safety
instructions in the System Information document.
9D904eb4.fm Page 1 Tuesday, October 1, 2002 11:55 PM
1-2 Microprocessor Upgrade Instal lat ion Guide
w w
w .d
e ll
.c o
m |
s u
p p
o r
t .d
e ll
.c o
m 3 Remove the cooling shroud, if applicable (see your Installation and Troubleshooting Guide).
4 If you are upgrading an existing microprocessor, remove the microprocessor heat sink.
NOTE: If a cooling fan is mounted on the heat sink, you can remove the heat sink without
removing the fan. However, you can remove the fan to provide easier access to the heat-sink
retention clip(s). For information on removing a cooling fan, see your Installation and
Troubleshooting Guide.
a Remove the retention clip(s) securing the heat sink to the microprocessor by pressing down firmly on the retention clip tab, and then removing the clip from the heat sink.
See your system information label on the system cover for heat-sink retention clip information.
CAUTION: The microprocessor and heat sink can become extremely hot. Be sure
they have had sufficient time to cool before handling.
NOTICE: Never remove the heat sink from a microprocessor unless you intend to remove the
microprocessor. The heat sink is necessary to maintain proper thermal conditions.
NOTICE: After removing the heat sink, place it upside down on a flat surface to prevent the
thermal interface material from being damaged or contaminated.
b Remove the heat sink. See your Installation and Troubleshooting Guide for information on removing the heat sink.
5 Swing the socket release lever upward to the fully open position (see Figure 1-1).
NOTICE: Be careful not to bend any of the pins when removing the microprocessor. Bending
the pins can permanently damage the microprocessor.
6 Lift the microprocessor out of the socket and leave the release lever in the open position so that the socket is ready for the new microprocessor.
NOTICE: Be careful not to bend any of the pins when unpacking the microprocessor. Bending
the pins can permanently damage the microprocessor.
7 Unpack the new microprocessor.
If any of the pins on the microprocessor appear bent, see "Getting Help" in your Installation and Troubleshooting Guide for instructions about obtaining technical assistance.
9D904eb4.fm Page 2 Tuesday, October 1, 2002 11:55 PM
Microprocessor Upgrade Instal lat ion Guide 1-3
F i g u r e 1 - 1 . Re m o v i n g a n d Re p l a c i n g t h e M i c r o p r o c e s s o r
NOTICE: Positioning the microprocessor incorrectly can permanently damage the
microprocessor and the system when you turn on the system. When placing the microprocessor
in the ZIF socket, be sure that all of the pins on the microprocessor go into the corresponding
holes. Be careful not to bend the pins.
8 Install the microprocessor in the socket (see Figure 1-1).
a Ensure that the microprocessor socket release lever is in the fully open position.
b Align pin 1 on the microprocessor with pin 1 on the microprocessor socket.
c With pin 1 of the microprocessor and socket aligned, set the microprocessor lightly in the socket and ensure that all pins are matched with the correct holes in the socket.
Because the system uses a ZIF microprocessor socket, there is no need to use force (which could bend the pins if the microprocessor is misaligned). When the microprocessor is positioned correctly, it should drop down into the socket with minimal pressure.
d When the microprocessor is fully seated in the socket, rotate the socket release lever back down until it snaps into place, locking the microprocessor in the socket.
pin-1 locators
microprocessor
microprocessor socket
9D904eb4.fm Page 3 Tuesday, October 1, 2002 11:55 PM
1-4 Microprocessor Upgrade Instal lat ion Guide
w w
w .d
e ll
.c o
m |
s u
p p
o r
t .d
e ll
.c o
m 9 Install the heat sink.
If the heat sink provided has a foil thermal interface material strip on the bottom of the heat sink, place the heat sink on the microprocessor.
If the heat sink provided has a thermal grease tab, remove the tab and place the heat sink on the microprocessor.
If heat-sink thermal grease is provided, clean the heat sink and apply the thermal grease before placing the heat sink on the microprocessor.
See your system information label on the system cover for the correct heat sink orientation.
NOTICE: To avoid possible damage to the microprocessor, you must align the heat sink so that
the triangular mark on the heat sink points toward the triangular mark on the system board, if
applicable.
10 Orient the heat-sink retention clip as shown in your Installation and Troubleshooting Guide.
11 Hook the end of the clip without the release tab over the tab on the edge of the socket.
12 Press down on the release tab until the hole on the clip latches onto the ZIF socket tab.
NOTICE: If a cooling fan is provided with your upgrade kit, you must install the fan on the
microprocessor heat sink to provide proper thermal conditions. For information on installing a
cooling fan, see your Installation and Troubleshooting Guide.
13 If a cooling fan is provided with your upgrade kit or if you removed a cooling fan earlier in this procedure, install the fan on the microprocessor heat sink.
14 Install the VRM(s):
a If you are adding a secondary microprocessor, examine the VRM to ensure that it is the correct VRM for your system.
b Insert the VRM in the appropriate secondary VRM connector, ensuring that the latches at each end of the connector engage (see Figure 1-2).
c If you received two VRMs with the upgrade kit, replace the primary VRM already installed in the system with one of the VRMs from the upgrade kit.
NOTE: The system does not support mismatched VRMs.
9D904eb4.fm Page 4 Tuesday, October 1, 2002 11:55 PM
Microprocessor Upgrade Instal lat ion Guide 1-5
F i g u r e 1 - 2 . I n s t a l l i n g a V R M
15 Replace the cooling shroud, if applicable (see your Installation and Troubleshooting Guide).
16 Close the system doors, or replace the system cover (see your Installation and Troubleshooting Guide).
17 Reconnect your system and peripherals to their electrical outlets, and turn them on.
As the system boots, it detects the presence of the new processor and automatically changes the system configuration information in the System Setup program.
NOTE: After you access the inside of the system, the chassis intrusion detector will cause
an alert message to be displayed at the next system startup. This message is stored in the
systems nonvolatile random-access memory (NVRAM). To clear this message log, see your
systems management software documentation.
18 Enter the System Setup program and ensure that the microprocessor categories match the new system configuration. For instructions about using the System Setup program, see your Users Guide.
19 Run the system diagnostics to verify that the new microprocessor is operating correctly. See your Installation and Troubleshooting Guide for information about running the diagnostics and troubleshooting any problems that may occur.
VRM
VRM connector
latches (2)
connector key
9D904eb4.fm Page 5 Tuesday, October 1, 2002 11:55 PM
1-6 Microprocessor Upgrade Instal lat ion Guide
w w
w .d
e ll
.c o
m |
s u
p p
o r
t .d
e ll
.c o
m
9D904eb4.fm Page 6 Tuesday, October 1, 2002 11:55 PM
w w w. d e l l . c o m | s u p p o r t . d e l l . c o m
Dell
9D904ct4.fm Page 1 Tuesday, October 1, 2002 11:38 PM
2002 Dell Computer Corporation
Dell Computer Corporation
Dell DELL Dell Computer Corporation
Dell Computer
Corporation
2002 10 P/N 9D904 Rev. A04
9D904ct4.fm Page 2 Tuesday, October 1, 2002 11:38 PM
2-1
Dell Web support.dell.com
BIOS BIOS
(PGA)
ZIF
ZIF ZIF
VRM
1
2
3
4
a
9D904cb4.fm Page 1 Tuesday, October 1, 2002 11:37 PM
2-2
w w
w .d
e ll
.c o
m |
s u
p p
o r
t .d
e ll
.c o
m
b
5 2-1
6
7
2-1
1
9D904cb4.fm Page 2 Tuesday, October 1, 2002 11:37 PM
2-3
ZIF
8 2-1
a
b 1 1
c 1
ZIF
d
9
10
11
12 ZIF
13
14 VRM
a VRM
9D904cb4.fm Page 3 Tuesday, October 1, 2002 11:37 PM
2-4
w w
w .d
e ll
.c o
m |
s u
p p
o r
t .d
e ll
.c o
m b VRM VRM
2-2
c VRM VRM
VRM
VRM
2-2 VRM
15
16
17
(NVRAM)
18
19
VRM
VRM
2
9D904cb4.fm Page 4 Tuesday, October 1, 2002 11:37 PM
w w w. d e l l . c o m | s u p p o r t . d e l l . c o m
Systmes Dell
Guide d'installation pour la mise
niveau du microprocesseur
9D904ft4.fm Page 1 Tuesday, October 1, 2002 10:59 PM
Remarques, mises en garde et avertissements REMARQUE : UNE REMARQUE indique une information importante destine vous aider mieux utiliser votre ordinateur.
MISE EN GARDE : UNE MISE EN GARDE indique un dommage potentiel pouvant survenir (ou une perte de donnes) et vous dit comment viter le problme.
ATTENTION : Le message ATTENTION indique une situation potentiellement
dangereuse qui, si elle n'est pas vite, peut provoquer une blessure mineure ou
modre.
Les informations fournies dans ce document sont susceptibles d'tre modifies sans pravis. 2002 Dell Computer Corporation. Tous droits rservs.
La reproduction de ce document de quelque manire que ce soit sans l'autorisation crite de Dell Computer Corporation est strictement interdite.
Marques dposes utilises dans ce guide : Dell et le logo DELL sont des marques de Dell Computer Corporation.
Toutes les autres marques dposes et noms de marques utiliss dans ce document se rapportent aux socits propritaires des marques et des noms de ces produits. Dell Computer Corporation dcline tout intrt dans l'utilisation des marques dposes et des noms de marques ne lui appartenant pas.
octobre 2002 Rf. 9D904 Rv. A04
9D904ft4.fm Page 2 Tuesday, October 1, 2002 10:59 PM
Guide d ' instal lat ion pour la mise niveau du microprocesseur 3-1
Ce document contient des instructions concernant l'ajout ou le remplacement de
microprocesseurs. Pour pouvoir tirer parti des futures options offrant une vitesse plus leve
ou des fonctionnalits supplmentaires, vous pouvez ajouter des microprocesseurs
secondaires ou remplacer ceux qui sont dj installs dans votre systme.
MISE EN GARDE : Avant d'ajouter ou de remplacer un microprocesseur, consultez les
dernires informations sur le BIOS systme sur le site Web de support de Dell,
support.dell.com, et mettez niveau le BIOS si ncessaire.
Chaque microprocesseur et sa mmoire cache associe sont contenus dans un module PGA
(pin-grid array) qui est install dans un connecteur ZIF sur la carte systme. La sous-section
suivante explique comment installer ou remplacer le microprocesseur sur les connecteurs
pour microprocesseur principal ou secondaire.
REMARQUE : Dans un systme un seul microprocesseur, celui-ci doit tre install
dans le connecteur de microprocesseur principal.
Ajout ou remplacement d'un microprocesseur MISE EN GARDE : Le type et la vitesse des microprocesseurs secondaires doivent
tre identiques ceux du microprocesseur principal. Si les vitesses des
microprocesseurs diffrent, c'est la vitesse du microprocesseur le plus lent qui est
adopte.
Outre le connecteur ZIF destin au microprocesseur principal sur la carte systme, il peut
exister d'autres connecteurs ZIF prvus pour accueillir des microprocesseurs secondaires.
Le kit de mise niveau du microprocesseur contient les lments suivants :
Un microprocesseur
Un dissipateur thermique
Languette(s) de fixation du dissipateur thermique
Un module VRM, qui est utilis en cas d'ajout d'un microprocesseur secondaire
Votre kit de mise niveau peut aussi comporter un ventilateur.
ATTENTION : Avant d'excuter cette procdure, lisez les instructions de scurit
du document Informations sur le systme.
1 Mettez le systme hors tension, y compris les priphriques, puis dbranchez le cordon d'alimentation du secteur.
2 Ouvrez les portes du systme, ou retirez le capot du systme (reportez-vous au Guide d'installation et de dpannage).
ATTENTION : Reportez-vous la section Protection contre les dcharges
lectrostatiques dans les instructions de scurit du document Informations sur
le systme.
9D904fb4.fm Page 1 Tuesday, October 1, 2002 10:35 PM
3-2 Guide d ' instal lat ion pour la mise niveau du processeur
w w
w .d
e ll
.c o
m |
s u
p p
o r
t .d
e ll
.c o
m 3 Retirez le dissipateur de chaleur, le cas chant (reportez-vous au Guide d'installation et de dpannage).
4 Si vous mettez niveau un microprocesseur dj install, retirez son dissipateur thermique.
REMARQUE : Si un ventilateur est mont sur le dissipateur thermique, vous
pouvez le retirer sans enlever le ventilateur. Toutefois, vous pouvez retirer le
ventilateur pour accder plus facilement aux languettes de fixation du dissipateur
thermique. Pour savoir comment retirer le ventilateur, reportez-vous au Guide
d'installation et de dpannage.
a Retirez la ou les languettes de fixation assujettissant le dissipateur thermique au microprocesseur en appuyant fermement sur la patte de la languette, puis en retirant la languette du dissipateur thermique.
Consultez l'tiquette d'informations appose sur le capot du systme pour plus de prcisions sur la languette de fixation du dissipateur thermique.
ATTENTION : Le microprocesseur et le dissipateur thermique peuvent tre
brlants. Laissez-les se refroidir suffisamment avant de les manipuler.
MISE EN GARDE : Ne retirez jamais le dissipateur thermique d'un microprocesseur
si vous n'avez pas l'intention de retirer le microprocesseur lui-mme. Le dissipateur
thermique est en effet indispensable pour maintenir les conditions de temprature
adquates.
MISE EN GARDE : Aprs avoir retir le dissipateur thermique, placez-le l'envers
sur une surface plane afin d'empcher toute dtrioration ou contamination du
matriau de l'interface thermique.
b Retirez le dissipateur thermique. Reportez-vous au Guide d'installation et de dpannage pour savoir comment procder.
5 Poussez fond vers le haut la manette de dgagement du connecteur afin de la placer en position ouverte (voir la Figure 3-1).
MISE EN GARDE : Veillez ne pas tordre les broches lors du retrait du
microprocesseur. Vous risqueriez sinon d'endommager dfinitivement le
microprocesseur.
6 Extrayez le microprocesseur du connecteur et laissez la manette de dgagement en position ouverte, de faon ce que le connecteur soit prt accueillir le nouveau microprocesseur.
MISE EN GARDE : Veillez ne pas tordre les broches lorsque vous extrayez le
microprocesseur de son emballage. Vous risqueriez sinon d'endommager
dfinitivement le microprocesseur.
9D904fb4.fm Page 2 Tuesday, October 1, 2002 10:35 PM
Guide d ' instal lat ion pour la mise niveau du microprocesseur 3-3
7 Sortez le nouveau microprocesseur de son emballage.
Si certaines broches du microprocesseur semblent tordues, reportez-vous la section Obtention d'aide dans le Guide d'installation et de dpannage pour savoir comment demander une assistance technique.
F i g u r e 3 - 1 . Re t r a i t e t r e m p l a c e m e n t d u m i c r o p r o c e s s e u r
MISE EN GARDE : Un mauvais positionnement du microprocesseur risquerait
d'endommager dfinitivement le microprocesseur et le systme lorsque vous le
remettrez sous tension. Lors de l'installation du microprocesseur dans le connecteur
ZIF, vrifiez que toutes les broches du microprocesseur s'enfoncent dans les trous
correspondants. Faites trs attention ne pas tordre les broches.
8 Installez le microprocesseur dans le connecteur (voir la Figure 3-1).
a Assurez-vous que la manette de dgagement du microprocesseur est en position ouverte.
b Faites correspondre la broche 1 du microprocesseur sur la broche 1 du connecteur du microprocesseur.
repres de
la broche 1
microprocesseur
connecteur du
microprocesseur
9D904fb4.fm Page 3 Tuesday, October 1, 2002 10:35 PM
3-4 Guide d ' instal lat ion pour la mise niveau du processeur
w w
w .d
e ll
.c o
m |
s u
p p
o r
t .d
e ll
.c o
m c Une fois les broches 1 du microprocesseur et du connecteur alignes, mettez doucement en place le microprocesseur dans le connecteur et assurez-vous que toutes les broches correspondent bien aux trous appropris du connecteur.
Le connecteur ZIF vous vite de devoir forcer pour installer le microprocesseur (ce qui risquerait de tordre les broches si le microprocesseur n'est pas bien align). Une fois le microprocesseur correctement positionn, une pression trs lgre doit suffire pour pouvoir l'enfoncer dans le connecteur.
d Lorsque le microprocesseur est install fond dans le connecteur, faites pivoter et abaissez la manette de dgagement du connecteur jusqu' ce qu'elle s'enclenche, verrouillant le microprocesseur dans le connecteur.
9 Installez le dissipateur thermique.
Si le dessous du dissipateur thermique est recouvert d'une feuille de protection thermique en papier mtallis, placez le dissipateur thermique sur le microprocesseur.
Si le dissipateur thermique est dot d'une patte recouverte de graisse de protection thermique, retirez cette patte et placez le dissipateur thermique sur le microprocesseur.
Si la graisse de protection thermique est fournie part, nettoyez le dissipateur thermique et appliquez-lui une couche de cette graisse avant de le placer sur le microprocesseur.
Consultez l'tiquette d'informations appose sur le capot du systme pour savoir comment orienter le dissipateur thermique.
MISE EN GARDE : Pour viter d'endommager le microprocesseur, vous devez orienter
le dissipateur thermique de faon ce que le repre triangulaire du dissipateur pointe
vers le repre triangulaire de la carte systme, le cas chant.
10 Orientez la languette de fixation du dissipateur thermique en procdant comme indiqu dans le Guide d'installation et de dpannage.
11 Accrochez l'extrmit de la languette sans la patte de dgagement sur la patte situe sur le rebord du connecteur.
12 Appuyez sur la patte de dgagement jusqu' ce que le trou de la languette s'enclenche sur la patte du connecteur ZIF.
MISE EN GARDE : Si votre kit de mise niveau comporte un ventilateur, vous devez
installer le ventilateur sur le dissipateur thermique du microprocesseur afin de
maintenir une temprature approprie. Pour savoir comment installer le ventilateur,
reportez-vous au Guide d'installation et de dpannage.
9D904fb4.fm Page 4 Tuesday, October 1, 2002 10:35 PM
Guide d ' instal lat ion pour la mise niveau du microprocesseur 3-5
13 Si votre kit de mise niveau comporte un ventilateur ou si vous avez retir un ventilateur au cours de cette procdure, vous devez installer le ventilateur sur le dissipateur thermique du microprocesseur..
14 Installez le ou les modules VRM :
a Si vous ajoutez un microprocesseur secondaire, examinez le module VRM et assurez-vous qu'il convient votre systme.
b Introduisez le module VRM dans le connecteur VRM secondaire appropri, en veillant ce que les loquets placs chaque extrmit du connecteur s'enclenchent (voir la Figure 3-2).
c Si vous avez reu deux modules VRM avec le kit de mise niveau, remplacez le module VRM principal dj install sur le systme avec l'un des VRM du kit.
REMARQUE : Le systme ne prend pas en charge les modules VRM non
quivalents.
F i g u r e 3 - 2 . I n s t a l l a t i o n d ' u n m o d u l e V R M
15 Remettez en place le dissipateur de chaleur, le cas chant (reportez-vous au Guide d'installation et de dpannage).
16 Fermez les portes du systme, ou remettez en place le capot du systme (reportez-vous au Guide d'installation et de dpannage).
VRM
VRM connector latches (2)
connector key
9D904fb4.fm Page 5 Tuesday, October 1, 2002 10:35 PM
3-6 Guide d ' instal lat ion pour la mise niveau du processeur
w w
w .d
e ll
.c o
m |
s u
p p
o r
t .d
e ll
.c o
m 17 Rebranchez le systme et les priphriques sur leurs prises lectriques, puis remettez- les sous tension.
Lors de l'initialisation, le systme dtecte la prsence du nouveau processeur et modifie automatiquement les informations de configuration du systme dans le programme System Setup.
REMARQUE : Aprs que vous avez accd l'intrieur du systme, le dtecteur
d'ouverture non autorise du chssis provoque l'affichage d'un message d'alerte
lors du redmarrage suivant du systme. Ce message est enregistr dans la
mmoire NVRAM du systme. Pour savoir comment effacer ce message, consultez
la documentation du logiciel de gestion du systme.
18 Accdez au programme de configuration du systme (System Setup) et vrifiez que les catgories du microprocesseur correspondent bien la nouvelle configuration. Pour plus d'informations sur le programme System Setup, reportez-vous au Guide de l'utilisateur.
19 Excutez les diagnostics du systme pour vrifier que le nouveau microprocesseur fonctionne correctement. Reportez-vous au Guide d'installation et de dpannage pour plus d'informations sur l'excution des diagnostics et du dpannage des problmes ventuels.
9D904fb4.fm Page 6 Tuesday, October 1, 2002 10:35 PM
w w w. d e l l . c o m | s u p p o r t . d e l l . c o m
Dell-Systeme
Installationsanleitung fr
Mikroprozessor-Upgrades
9D904gt4.fm Page 1 Tuesday, October 1, 2002 10:57 PM
Hinweis, Bitte Beachten und Vorsicht HINWEIS: Ein HINWEIS enthlt wichtige Informationen, mit deren Hilfe Sie Ihren Computer besser nutzen knnen.
BITTE BEACHTEN: BITTE BEACHTEN weist auf eine mgliche Beschdigung von Hardware oder den Verlust von Daten hin und beschreibt, wie dieses Problem vermieden werden kann.
VORSICHT: VORSICHT weist darauf hin, dass Gefahr fr einen Sachschaden,
Personenschaden oder Lebensgefahr besteht.
Die in diesem Dokument enthaltenen Informationen knnen ohne Vorankndigung gendert werden. 2002 Dell Computer Corporation. Alle Rechte vorbehalten.
Eine Reproduktion dieses Dokuments in jeglicher Form ist nur mit vorheriger schriftlicher Genehmigung der Dell Computer Corporation erlaubt.
Die in diesem Text verwendeten Warenzeichen: Dell und das DELL-Logo sind Warenzeichen der Dell Computer Corporation.
Andere in diesem Dokument mglicherweise verwendete Warenzeichen und Handelsbezeichnungen sind unter Umstnden Marken und Namen der entsprechenden Firmen oder ihrer Produkte. Die Dell Computer Corporation erhebt keinen Anspruch auf Warenzeichen oder Handelsnamen mit Ausnahme ihrer eigenen.
Oktober 2002 P/N 9D904 Rev. A04
9D904gt4.fm Page 2 Tuesday, October 1, 2002 10:57 PM
Instal lat ionsanleitung fr Mikroprozessor-Upgrades 4-1
Dieses Dokument enthlt eine Anleitung fr das Hinzufgen oder Ersetzen von Mikroprozessoren. Um von zuknftigen Verbesserungen hinsichtlich der Geschwindigkeit und neuer Optionen profitieren zu knnen, knnen Sie zustzliche (sekundre) Mikroprozessoren installieren oder die installierten Prozessoren austauschen.
BITTE BEACHTEN: Bevor Sie einen Mikroprozessor hinzufgen oder austauschen,
berprfen Sie die aktuellsten System-BIOS-Informationen auf der Dell Support-
Website unter support.dell.com und aktualisieren Sie Ihr BIOS, falls erforderlich.
Jeder Mikroprozessor und der zugehrige Cache-Speicher sind in einem PGA-Paket (Pin- Grid Array) enthalten, das in einem ZIF-Sockel auf der Mikroprozessor-Platine installiert ist. Im folgenden Unterabschnitt wird beschrieben, wie der Mikroprozessor im Sockel des primren oder sekundren Mikroprozessors eingebaut oder ausgetauscht wird.
HINWEIS: In einem System mit nur einem Mikroprozessor muss der Prozessor im
primren Prozessorsockel installiert sein.
Hinzufgen oder Austauschen eines Mikroprozessors
BITTE BEACHTEN: Die sekundren Mikroprozessoren mssen vom gleichen Typ sein
wie der primre Mikroprozessor und die gleiche Taktfrequenz wie dieser haben. Wenn
die Mikroprozessoren unterschiedliche Taktfrequenzen haben, arbeiten sie alle mit der
Taktfrequenz des langsameren Prozessors.
Neben dem ZIF-Sockel fr den primren Mikroprozessor befinden sich auf der Systemplatine mglicherweise weitere ZIF-Sockel fr sekundre Mikroprozessoren.
Das Mikroprozessor-Upgrade-Kit enthlt die folgenden Teile:
Einen Mikroprozessor
Ein Wrmeableitblech
Halteclip(s) fr das Wrmeableitblech
Ein VRM, falls ein sekundrer Mikroprozessor hinzugefgt wird.
Eventuell enthlt Ihr Upgrade-Kit auerdem einen Lfter.
VORSICHT: Bevor Sie mit diesem Verfahren beginnen, lesen Sie zunchst die
Sicherheitshinweise im Dokument Systeminformation.
1 Schalten Sie das System und smtliche Peripheriegerte aus und trennen Sie das Netzkabel von der Stromversorgung.
2 ffnen sie die Tren des Systems oder entfernen Sie die Systemabdeckung (siehe dazu Anleitung zur Installation und Fehlersuche).
9D904gb4.fm Page 1 Tuesday, October 1, 2002 10:41 PM
4-2 Instal lat ionsanleitung fr Mikroprozessor-Upgrades
w w
w .d
e ll
.c o
m |
s u
p p
o r
t .d
e ll
.c o
m VORSICHT: Siehe Schutz vor elektrostatischer Entladung in den
Sicherheitshinweisen im Dokument Systeminformation.
3 Entfernen Sie ggf. den Khlkrper (siehe dazu Anleitung zur Installation und Fehlersuche).
4 Wenn Sie ein Mikroprozessor-Update durchfhren, entfernen Sie das Wrmeableitblech des Prozessors.
HINWEIS: Wenn ber dem Wrmeableitblech ein Lfter montiert ist, brauchen
Sie nur das Blech zu entfernen. Allerdings knnen Sie auch den Lfter entfernen,
um den/die Halteclip(s) des Wrmelableitblechs einfacher zu erreichen. Nhere
Informationen zum Ausbau eines Lfters siehe Anleitung zur Installation und
Fehlersuche.
a Entfernen Sie die Halteclips, mit denen das Wrmeableitblech am Mikro- prozessor befestigt ist, indem Sie fest auf die Lasche an den Clips drcken und sie dann vom Ableitblech abnehmen.
Informationen zum Halteclip des Wrmeableitblechs finden Sie auf dem Systeminformations-Etikett auf der Abdeckung des Systems.
VORSICHT: Mikroprozessor und Wrmeableitblech knnen sehr hei werden.
Stellen Sie sicher, dass beide Komponenten ausreichend Zeit zum Abkhlen
haben, bevor Sie sie berhren.
BITTE BEACHTEN: Nehmen Sie das Wrmeableitblech nur dann von einem
Mikroprozessor ab, wenn Sie den Mikroprozessor entfernen mchten. Das
Wremeableitblech ist fr die Aufrechterhaltung der korrekten Temperaturbedingungen
erforderlich.
BITTE BEACHTEN: Wenn das Wrmeableitblech entfernt ist, legen Sie es umgedreht
auf einen ebenen Untergrund, damit das Thermoschnittstellen-Material nicht
beschdigt oder verschmutzt wird.
b Nehmen Sie das Wrmeableitblech ab. Nheres zum Ausbau des Wrme- ableitblechs finden Sie in der Anleitung zur Installation und Fehlersuche.
5 Drehen Sie den Entriegelungshebel des Sockels nach oben in die vollstndig geffnete Position (siehe Abbildung 4-1).
BITTE BEACHTEN: Achten Sie sorgfltig darauf, keine Pins zu verbiegen, wenn Sie
den Mikroprozessor herausnehmen. Ein Verbiegen der Pins kann eine dauerhafte
Beschdigung des Mikroprozessors zur Folge haben.
6 Heben Sie den Mikroprozessor aus dem Sockel, und belassen Sie den Hebel in der senkrechten Position, damit der neue Mikroprozessor in den Sockel eingepasst werden kann.
BITTE BEACHTEN: Achten Sie sorgfltig darauf, keine Pins zu verbiegen, wenn Sie
den Mikroprozessor auspacken. Ein Verbiegen der Pins kann eine dauerhafte
Beschdigung des Mikroprozessors zur Folge haben.
9D904gb4.fm Page 2 Tuesday, October 1, 2002 10:41 PM
Instal lat ionsanleitung fr Mikroprozessor-Upgrades 4-3
7 Nehmen Sie den neuen Mikroprozessor aus seiner Verpackung.
Falls Pins am Mikroprozessor verbogen zu sein scheinen, erfahren Sie unter Hilfestellung in der Anleitung zur Installation und Fehlersuche Ihres Systems, wie Sie technische Untersttzung erhalten knnen.
A b b i l d u n g 4 - 1 . E n t f e r n e n u n d E i n b a u e n d e s M i k r o p r o z e s s o r s
BITTE BEACHTEN: Wird der Mikroprozessor falsch eingesetzt, kann dies beim
Einschalten des Systems eine dauerhafte Beschdigung des Mikroprozessors und des
Systems zur Folge haben. Stellen Sie beim Einsetzen des Mikroprozessors in den ZIF-
Sockel sicher, dass alle Pins des Mikroprozessors in die entsprechenden Lcher
eingreifen. Achten Sie darauf, die Pins nicht zu verbiegen.
8 Bauen Sie den Mikroprozessor in den Sockel ein (siehe Abbildung 4-1).
a Achten Sie darauf, dass der Entriegelungshebel des Mikroprozessor-Sockels in der vollstndig geffneten Position steht.
b Richten Sie Pin 1 am Mikroprozessor nach Pin 1 am Mikroprozessor-Sockel aus.
Abgleichmar-
kierungen Pin 1
Mikroprozessor
Mikroprozessor-Sockel
9D904gb4.fm Page 3 Tuesday, October 1, 2002 10:41 PM
4-4 Instal lat ionsanleitung fr Mikroprozessor-Upgrades
w w
w .d
e ll
.c o
m |
s u
p p
o r
t .d
e ll
.c o
m c Wenn Pin 1 des Mikroprozessors nach dem Sockel ausgerichtet ist, setzen Sie den Mikroprozessor vorsichtig in den Sockel ein und stellen Sie sicher, dass alle Pins in die korrekten Lcher im Sockel eingreifen.
Da das System einen ZIF-Mikroprozessor-Sockel verwendet, muss keine Kraft aufgewendet werden (wenn der Prozessor falsch ausgerichtet ist, knnten Sie sonst die Pins verbiegen). Wenn der Mikroprozessor korrekt positioniert ist, sollte er mit minimalem Druck in den Sockel eingepasst werden knnen.
d Sitzt der Mikroprozessor ordnungsgem im Sockel, bewegen Sie den Hebel zum Lsen des Sockels wieder nach unten, bis er einrastet. Hierdurch wird der Mikroprozessor im Sockel verriegelt.
9 Bauen Sie das Wrmeableitblech ein.
Falls das Wrmeableitblech an der Unterseite mit einem Folienstreifen aus Thermoschnittstellen-Material versehen ist, platzieren Sie das Ableitblech auf den Mikroprozessor.
Falls das Ableitblech eine Thermofett-Lasche besitzt, nehmen Sie die Lasche ab und setzen Sie das Blech auf den Mikroprozessor.
Falls Thermofett fr das Wrmeableitblech mitgeliefert wurde, reinigen Sie das Blech und tragen Sie das Thermofett auf, bevor Sie das Blech auf den Mikroprozessor setzen.
Informationen zur korrekten Ausrichtung des Wrmeableitblechs finden Sie auf dem Systeminformations-Etikett auf der Systemabdeckung.
BITTE BEACHTEN: Um eine mgliche Beschdigung des Mikroprozessors zu
vermeiden, muss der Lfter so ausgerichtet werden, dass die dreieckige Markierung
am Lfter auf die dreieckige Markierung auf der Systemplatine zeigt (falls
zutreffend).
10 Richten Sie den Halteclip des Wrmeableitblechs wie in der Anleitung zur Installation und Fehlersuche gezeigt aus.
11 Haken Sie das Ende des Clips ohne Lasche in die Lasche am Rand des Sockels ein.
12 Drcken Sie auf die Entriegelungslasche, bis das Loch im Clip in die Lasche am ZIF- Sockel einrastet.
BITTE BEACHTEN: Wenn Ihr Upgrade-Kit einen Lfter enthlt, mssen Sie ihn auf
dem Wrmeableitblech des Mikroprozessors installieren, um ordnungsgeme
Temperaturbedingungen zu erzeugen. Nhere Informationen zur Installation eines
Lfters finden Sie in der Anleitung zur Installation und Fehlersuche.
9D904gb4.fm Page 4 Tuesday, October 1, 2002 10:41 PM
Instal lat ionsanleitung fr Mikroprozessor-Upgrades 4-5
13 Wenn Ihr Upgrade-Kit einen Lfter enthlt oder wenn Sie zu Beginn dieser Prozedur einen Lfter ausgebaut haben, installieren Sie ihn auf dem Wrmeableitblech des Mikroprozessors.
14 Installieren Sie die VRM(s)
a Wenn Sie einen sekundren Mikroprozessor hinzufgen, berprfen Sie das VRM und stellen Sie sicher, dass es sich um das korrekte VRM fr Ihr System handelt.
b Setzen Sie das VRM in den geeigneten Steckplatz fr das sekundre VRM ein und stellen Sie sicher, dass die Riegel an beiden Enden des Steckplatzes einrasten (siehe Abbildung 4-2).
c Wenn Sie in Ihrem Upgrade-Kit zwei VRMs erhalten haben, ersetzen Sie den bereits im System installierten ersten VRM durch einen der VRMs aus dem Upgrade-Kit.
HINWEIS: Das System untersttzt keine unterschiedlichen VRMs.
A b b i l d u n g 4 - 2 . I n s t a l l a t i o n e i n e s V R M
15 Bringen Sie ggf. den Khlkrper wieder an (siehe dazu Anleitung zur Installation und Fehlersuche).
16 Schlieen sie die Tren des Systems oder bringen Sie die Systemabdeckung wieder an (siehe dazu Anleitung zur Installation und Fehlersuche).
VRM
VRM-Stecker
Riegel (2)
Steckermarkierung
9D904gb4.fm Page 5 Tuesday, October 1, 2002 10:41 PM
4-6 Instal lat ionsanleitung fr Mikroprozessor-Upgrades
w w
w .d
e ll
.c o
m |
s u
p p
o r
t .d
e ll
.c o
m 17 Verbinden Sie das System und die Peripheriegerte wieder mit der Stromversorgung, und schalten Sie das System und die Gerte ein.
Beim Booten erkennt das System den neuen Prozessor und ndert automatisch die Systemkonfigurations-Daten im System-Setup-Programm.
HINWEIS: Wenn Sie an der Innenseite des Systems gearbeitet haben, bewirkt der
Chassis-Strungsdetektor, dass beim nchsten Hochfahren des Systems eine
Warnmeldung angezeigt wird. Diese Meldung wird im nicht flchtigen
Arbeitsspeicher (NVRAM) des Systems gespeichert. Informationen ber das
Verfahren zum Lschen dieses Meldungsprotokolls finden Sie in der
Dokumentation der Systemverwaltungs-Software.
18 Rufen Sie das Setup-Programm des Systems auf und stellen Sie sicher, dass die Mikroprozessor-Kategorien mit der neuen Systemkonfiguration bereinstimmen. Informationen ber die Verwendung des System-Setup-Programms finden Sie in Ihrem Benutzerhandbuch.
19 Fhren Sie die Systemdiagnose aus, um sicherzustellen, dass der neue Mikroprozessor korrekt arbeitet. Informationen zum Diagnoseprogramm und der Suche nach eventuellen Fehlern finden Sie in der Anleitung zur Installation und Fehlersuche.
9D904gb4.fm Page 6 Tuesday, October 1, 2002 10:41 PM
w w w. d e l l . c o m / j p / | s u p p o r t . j p . d e l l . c o m
Dell
9D904jt4.fm Page 1 Tuesday, October 1, 2002 11:31 PM
:
:
:
2002 Dell Computer Corporation
Dell Computer Corporation
Dell DELL Dell Computer Corporation
Dell Computer Corporation
2002 10 P/N 9D904 Rev. A04
9D904jt4.fm Page 2 Tuesday, October 1, 2002 11:31 PM
5-1
: Dell Web support.dell.com BIOS BIOS
ZIF PGA (pin-grid array)
:
:
ZIF ZIF
VRM
:
1
2 Installation and Troubleshooting Guide
9D904jb4.fm Page 1 Wednesday, October 2, 2002 12:23 AM
5-2
w w
w .d
e ll
.c o
m /j
p /
| s
u p
p o
r t .j
p .d
e ll
.c o
m :
3 Installation and Troubleshooting Guide
4
:
Installation and Troubleshooting Guide
a
:
:
:
b
Installation and Troubleshooting Guide
5
5- 1
:
6
: 1
9D904jb4.fm Page 2 Wednesday, October 2, 2002 12:23 AM
5-3
7
1 Installation and Troubleshooting Guide
5-1.
:
ZIF
8 5-1
a
b 1 1
1
9D904jb4.fm Page 3 Wednesday, October 2, 2002 12:23 AM
5-4
w w
w .d
e ll
.c o
m /j
p /
| s
u p
p o
r t .j
p .d
e ll
.c o
m c 1
ZIF
d
9
:
10 Installation and Troubleshooting Guide
11
12 ZIF
:
Installation and Troubleshooting Guide
9D904jb4.fm Page 4 Wednesday, October 2, 2002 12:23 AM
5-5
13
14 VRM
a VRM VRM
b VRM VRM 5-2
c 2 VRM VRM VRM 1
: VRM
5-2. VRM
15 Installation and Troubleshooting Guide
16 Installation and Troubleshooting Guide
VRM
VRM 2
9D904jb4.fm Page 5 Wednesday, October 2, 2002 12:23 AM
5-6
w w
w .d
e ll
.c o
m /j
p /
| s
u p
p o
r t .j
p .d
e ll
.c o
m 17
:
NVRAM RAM
18
19
Installation and Troubleshooting Guide
9D904jb4.fm Page 6 Wednesday, October 2, 2002 12:23 AM
w w w. d e l l . c o m | s u p p o r t . d e l l . c o m
Dell
9D904kt4.fm Page 1 Tuesday, October 1, 2002 11:45 PM
,
: .
: ,
.
: , .
.
2002 Dell Computer Corporation. .
Dell Computer Corporation .
: Dell, DELL Dell Computer Corporation .
. Dell Computer Corporation
.
2002 6 P/N 9D904 Rev. A04
9D904kt4.fm Page 2 Tuesday, October 1, 2002 11:45 PM
6-1
.
.
: Dell
(support.dell.com) BIOS BIOS
.
ZIF
PGA(Pin-Grid Array) .
.
: ,
.
:
. ,
.
ZIF ZIF .
:
1
1
VRM( )
.
:
.
1
.
2 (
).
9D904kb4.fm Page 1 Wednesday, October 2, 2002 12:26 AM
6-2
w w
w .d
e ll
.c o
m |
s u
p p
o r
t .d
e ll
.c o
m :
.
3 , ( ).
4
.
: ,
.
. .
a
.
.
: .
.
: ,
. .
:
.
b . .
5 ( 6-1 ).
: , .
.
6
.
: .
.
7 .
.
9D904kb4.fm Page 2 Wednesday, October 2, 2002 12:26 AM
6-3
6-1.
:
. ZIF
,
. , .
8 ( 6-1 ).
a .
b 1 1 .
c 1 . .
ZIF
.
. ,
.
d , .
1
9D904kb4.fm Page 3 Wednesday, October 2, 2002 12:26 AM
6-4
w w
w .d
e ll
.c o
m |
s u
p p
o r
t .d
e ll
.c o
m 9 .
,
.
,
.
,
.
.
: ,
( ).
10
.
11 .
12 ZIF .
: ,
.
.
13
.
14 VRM :
a VRM
.
b VRM VRM ( 6-2 ).
c 2 VRM VRM .
: VRM .
9D904kb4.fm Page 4 Wednesday, October 2, 2002 12:26 AM
6-5
6-2. VRM
15 , (
).
16 (
).
17 .
, System Setup
.
:
. NVRAM(NonVolatile Random-
Access Memory) .
.
18 System Setup
. System Setup
.
19
.
.
VRM
VRM
(2)
9D904kb4.fm Page 5 Wednesday, October 2, 2002 12:26 AM
6-6
w w
w .d
e ll
.c o
m |
s u
p p
o r
t .d
e ll
.c o
m
9D904kb4.fm Page 6 Wednesday, October 2, 2002 12:26 AM
w w w. d e l l . c o m | s u p p o r t . d e l l . c o m
Sistemas Dell
Gua de instalacin para la
actualizacin de
microprocesadores
9D904st4.fm Page 1 Tuesday, October 1, 2002 11:02 PM
Notas, avisos y precauciones NOTA: una NOTA indica informacin importante que le ayudar a usar mejor su ordenador.
AVISO: un AVISO indica un posible dao en el hardware o la prdida de datos e informa de cmo evitar el problema.
PRECAUCIN: un mensaje de PRECAUCIN indica la posibilidad de que el equipo resulte averiado, de sufrir lesiones personales o incluso la muerte.
La informacin de este documento est sujeta a modificaciones sin previo aviso. 2002 Dell Computer Corporation. Reservados todos los derechos.
Queda prohibida su reproduccin en cualquier medio sin la autorizacin por escrito de Dell Computer Corporation.
Marcas comerciales que aparecen en el texto: Dell y el logotipo de DELL son marcas comerciales de Dell Computer Corporation.
En este documento pueden utilizarse otras marcas y nombres comerciales para referirse a las entidades propietarias de dichas marcas y nombres, o a sus productos. Dell Computer Corporation renuncia a cualquier derecho sobre las marcas y nombres comerciales que no sean de su propiedad.
octubre 2002 P/N 9D904 Rev. A04
9D904st4.fm Page 2 Tuesday, October 1, 2002 11:02 PM
Gua de instalacin para la actual izacin de microprocesadores 7-1
Este documento proporciona instrucciones sobre la forma de aadir o sustituir
microprocesadores. Para poder utilizar las futuras opciones en cuanto a velocidad y
funciones, puede aadir microprocesadores secundarios o sustituir los microprocesadores
del sistema.
AVISO: Antes de agregar o sustituir un microprocesador, consulte la ltima
informacin del sistema BIOS en la pgina Web de Dell Support en la direccin
support.dell.com y ample la BIOS si es necesario.
Cada microprocesador y su memoria cach asociada estn contenidos en un paquete de
matrices de rejillas de contacto (PGA) que se instala en un zcalo ZIF en la placa del
sistema. En la siguiente subseccin se describe cmo instalar o sustituir el microprocesador
de los zcalos del microprocesador primario o secundario.
NOTA: en un sistema con un solo microprocesador, el microprocesador debe instalarse
en el zcalo del microprocesador primario.
Adicin o sustitucin de un microprocesador AVISO: los microprocesadores secundarios deben ser del mismo tipo y velocidad que
el microprocesador primario. Si los microprocesadores tienen velocidades diferentes,
funcionarn a la velocidad del microprocesador ms lento.
Adems del zcalo ZIF del microprocesador primario de la placa del sistema, puede haber
otros zcalos ZIF en los que instalar microprocesadores secundarios.
El kit de actualizacin del microprocesador incluye los siguientes elementos:
Un microprocesador
Un disipador trmico
Clip(s) de retencin del disipador
Un VRM, que se utiliza si se aade un microprocesador secundario
El kit de actualizacin tambin puede incluir un ventilador de refrigeracin.
PRECAUCIN: antes de realizar este procedimiento, lea las instrucciones de seguridad en el documento Informacin del sistema.
1 Apague el sistema, incluidos todos los perifricos, y desconecte el cable de alimentacin de la toma de red.
2 Abra las puertas del sistema o retire la cubierta del sistema (consulte la Gua de instalacin y resolucin de problemas).
9D904sb4.fm Page 1 Tuesday, October 1, 2002 10:45 PM
7-2 Gua de instalacin para la actual izacin de microprocesadores
w w
w .d
e ll
.c o
m |
s u
p p
o r
t .d
e ll
.c o
m PRECAUCIN: consulte Proteccin contra descargas electrostticas en las instrucciones de seguridad del documento Informacin del sistema.
3 Retire la cubierta de refrigeracin, en caso aplicable (consulte la Gua de instalacin y solucin de problemas del sistema).
4 Si est actualizando un microprocesador existente, retire el disipador trmico del microprocesador.
NOTA: si est montado el ventilador de refrigeracin en el disipador trmico,
puede retirar el disipador sin quitar el ventilador. No obstante, puede retirar el
ventilador para facilitar el acceso a los clips de retencin del disipador trmico.
Para obtener informacin sobre la forma de extraer un ventilador de
refrigeracin, consulte la Gua de instalacin y resolucin de problemas.
a Retire los clips de retencin que fijan el disipador trmico al microprocesador presionando firmemente sobre la lengeta del clip de retencin y retirando el clip del disipador trmico.
Consulte la etiqueta que hay en la cubierta del sistema para ver informacin sobre el clip de retencin del disipador trmico.
PRECAUCIN: el microprocesador y el disipador trmico pueden estar extremadamente calientes. Asegrese de que ha tenido suficiente tiempo para enfriarse antes de tocarlo.
AVISO: nunca quite el disipador trmico de un microprocesador a menos que quiera
quitar el microprocesador. El disipador trmico es necesario para mantener las
condiciones trmicas adecuadas.
AVISO: tras retirar el disipador trmico, colquelo del revs sobre una superficie
plana para evitar que el material de la interfaz trmica se dae o se contamine.
b Quite el disipador trmico. Consulte la Gua de instalacin y resolucin de problemas para obtener informacin sobre la extraccin del disipador trmico.
5 Gire la palanca de liberacin del zcalo hacia arriba a la posicin totalmente abierta (consulte la Figura 7-1).
AVISO: tenga cuidado de no doblar ninguna de las patillas cuando quite el
microprocesador. Si las patillas se doblan, el microprocesador puede estropearse.
6 Levante el microprocesador del zcalo y deje la palanca de liberacin en la posicin abierta de forma que el zcalo est listo para el nuevo microprocesador.
AVISO: tenga cuidado de no doblar ninguna de las patillas cuando desembale el
microprocesador. Si las patillas se doblan, el microprocesador puede estropearse.
7 Desembale el nuevo microprocesador.
9D904sb4.fm Page 2 Tuesday, October 1, 2002 10:45 PM
Gua de instalacin para la actual izacin de microprocesadores 7-3
Si alguna de las patillas del microprocesador est doblada, consulte la seccin Obtencin de ayuda de la Gua de instalacin y resolucin de problemas para ver instrucciones sobre cmo solicitar asistencia tcnica.
F i g u r a 7 - 1 . E x t r a c c i n y s u s t i t u c i n d e l m i c r o p r o c e s a d o r
AVISO: si se coloca el microprocesador de forma incorrecta, al conectar el sistema
pueden estropearse tanto el microprocesador como el sistema. Cuando coloque el
microprocesador en el zcalo ZIF, asegrese de que todas las patillas encajan en sus
correspondientes orificios. Tenga cuidado de no doblar las patillas.
8 Instale el microprocesador en el zcalo (consulte la Figura 7-1).
a Asegrese de que la palanca de liberacin del zcalo del microprocesador est en la posicin totalmente abierta.
b Alinee la patilla 1 del microprocesador con la patilla 1 del zcalo del microprocesador.
localizadores
de 1 patilla
microprocesador
zcalo del
microprocesador
9D904sb4.fm Page 3 Tuesday, October 1, 2002 10:45 PM
7-4 Gua de instalacin para la actual izacin de microprocesadores
w w
w .d
e ll
.c o
m |
s u
p p
o r
t .d
e ll
.c o
m c Con la patilla 1 del microprocesador y el zcalo alineado, coloque el microprocesador ligeramente en el zcalo y asegrese de que todas las patillas coinciden con sus orificios del zcalo.
Como el sistema utiliza un zcalo de microprocesador ZIF, no es necesario aplicar fuerza (lo que doblara las patillas si el microprocesador no est bien alineado). Cuando el microprocesador est correctamente colocado, deber encajar en el zcalo con una presin mnima.
d Cuando el microprocesador est totalmente asentado en el zcalo, baje la palanca de liberacin del zcalo hasta que encaje en su sitio, lo que bloquear el microprocesador en el zcalo.
9 Instale el disipador trmico.
Si el disipador trmico tiene una tira de material de interfaz trmico metlico en el fondo, coloque el disipador sobre el microprocesador.
Si el disipador trmico tiene una lengeta de grasa trmica, quite la lengeta y coloque el disipador sobre el microprocesador.
Si se incluye grasa trmica para el disipador trmico, limpie el disipador y aplique la grasa trmica antes de colocar el disipador sobre el microprocesador.
Consulte la etiqueta que hay en la cubierta del sistema para ver la orientacin correcta del disipador trmico.
AVISO: para evitar posibles daos al microprocesador, debe alinear el disipador
trmico de forma que la marca triangular del disipador seale hacia la marca
triangular de la placa del sistema, en caso aplicable.
10 Oriente el clip de retencin del disipador trmico como se muestra en la Gua de instalacin y resolucin de problemas.
11 Enganche el extremo del clip sin la lengeta de liberacin sobre la lengeta del borde del zcalo.
12 Presione la lengeta de liberacin hasta que el orificio del clip se enganche en la lengeta del zcalo ZIF.
AVISO: si se proporciona un ventilador de refrigeracin con el kit de actualizacin,
debe instalar el ventilador en el disipador trmico del microprocesador para
proporcionar las condiciones trmicas adecuadas. Para obtener informacin sobre la
forma de instalar un ventilador de refrigeracin, consulte la Gua de instalacin y
resolucin de problemas.
13 Si se proporciona un ventilador de refrigeracin con el kit de actualizacin o si retir el ventilador de refrigeracin anteriormente en este procedimiento, instale el ventilador en el disipador trmico del microprocesador.
9D904sb4.fm Page 4 Tuesday, October 1, 2002 10:45 PM
Gua de instalacin para la actual izacin de microprocesadores 7-5
14 Instale el VRM(s):
a Si est aadiendo un microprocesador secundario, examine el VRM para comprobar que es el VRM (mdulo regulador de tensin) correcto para su sistema.
b Introduzca el VRM en el conector del VRM secundario apropiado, comprobando que los pestillos de cada extremo del conector se acoplan (consulte la Figura 7-2).
c Si recibe dos VRM con el kit de ampliacin, sustituya el primer VRM ya instalado en el sistema por uno de los VRM del kit.
NOTA: El sistema no admite VRM incorrectos.
F i g u r a 7 - 2 . I n s t a l a c i n d e l V R M
15 Vuelva a colocar la cubierta de refrigeracin, en caso aplicable (consulte la Gua de instalacin y solucin de problemas del sistema).
16 Cierre las puertas del sistema o vuelva a colocar la cubierta del sistema (consulte la Gua de instalacin y resolucin de problemas).
VRM
conector VRM
pestillos (2)
llave de conector
9D904sb4.fm Page 5 Tuesday, October 1, 2002 10:45 PM
7-6 Gua de instalacin para la actual izacin de microprocesadores
w w
w .d
e ll
.c o
m |
s u
p p
o r
t .d
e ll
.c o
m 17 Vuelva a conectar el sistema y los perifricos a las tomas de red y encendalos.
En cuanto el sistema arranque detectar la presencia del nuevo procesador y cambiar automticamente la informacin de configuracin del sistema en el programa de configuracin del sistema (System Setup).
NOTA: despus de acceder al interior del sistema, el detector de intrusin del
chasis generar un mensaje de alerta que aparecer la siguiente vez que arranque
el sistema. Este mensaje se almacena en la memoria de acceso aleatorio no voltil
(NVRAM) del sistema. Para borrar este mensaje, consulte la documentacin del
software de gestin del sistema.
18 Entre en el programa de configuracin del sistema (System Setup) y asegrese de que las categoras del microprocesador coinciden con la nueva configuracin del sistema. Si desea ms informacin sobre el programa de configuracin del sistema, consulte la Gua del usuario.
19 Ejecute los diagnsticos del sistema para verificar que el nuevo microprocesador est funcionando correctamente. Consulte la Gua de instalacin y resolucin de problemas para obtener informacin sobre la ejecucin de diagnsticos y resolucin de problemas que pudieran surgir.
9D904sb4.fm Page 6 Tuesday, October 1, 2002 10:45 PM
Related manuals for Dell PowerEdge 500SC Server Microprocessor Upgrade Installation Guide
Manualsnet FAQs
If you want to find out how the PowerEdge Dell works, you can view and download the Dell PowerEdge 500SC Server Microprocessor Upgrade Installation Guide on the Manualsnet website.
Yes, we have the Microprocessor Upgrade Installation Guide for Dell PowerEdge as well as other Dell manuals. All you need to do is to use our search bar and find the user manual that you are looking for.
The Microprocessor Upgrade Installation Guide should include all the details that are needed to use a Dell PowerEdge. Full manuals and user guide PDFs can be downloaded from Manualsnet.com.
The best way to navigate the Dell PowerEdge 500SC Server Microprocessor Upgrade Installation Guide is by checking the Table of Contents at the top of the page where available. This allows you to navigate a manual by jumping to the section you are looking for.
This Dell PowerEdge 500SC Server Microprocessor Upgrade Installation Guide consists of sections like Table of Contents, to name a few. For easier navigation, use the Table of Contents in the upper left corner.
You can download Dell PowerEdge 500SC Server Microprocessor Upgrade Installation Guide free of charge simply by clicking the “download” button in the upper right corner of any manuals page. This feature allows you to download any manual in a couple of seconds and is generally in PDF format. You can also save a manual for later by adding it to your saved documents in the user profile.
To be able to print Dell PowerEdge 500SC Server Microprocessor Upgrade Installation Guide, simply download the document to your computer. Once downloaded, open the PDF file and print the Dell PowerEdge 500SC Server Microprocessor Upgrade Installation Guide as you would any other document. This can usually be achieved by clicking on “File” and then “Print” from the menu bar.