Dell Chief RXT2 Mount Installation Guide PDF

1 of 12
1 of 12

Summary of Content for Dell Chief RXT2 Mount Installation Guide PDF

I N S T A L L A T I O N I N S T R U C T I O N S

Instrucciones de instalacin Installationsanleitung Instrues de Instalao

Istruzioni di installazione Installatie-instructies Instructions dinstallation

RMT2

RLT2

RXT2

Universal Tilt Mounts

Spanish Product Description German Product Description

Portuguese Product Description Italian Product Description Dutch Product Description

French Product Description

RMT2/RLT2/RXT2

RMT2/RLT2/RXT2 Installation Instructions

2

DISCLAIMER

Milestone AV Technologies and its affiliated corporations and subsidiaries (collectively "Milestone"), intend to make this manual accurate and complete. However, Milestone makes no claim that the information contained herein covers all details, conditions or variations, nor does it provide for every possible contingency in connection with the installation or use of this product. The information contained in this document is subject to change without notice or obligation of any kind. Milestone makes no representation of warranty, expressed or implied, regarding the information contained herein. Milestone assumes no responsibility for accuracy, completeness or sufficiency of the information contained in this document.

Chief is a registered trademark of Milestone AV Technologies. All rights reserved.

IMPORTANT SAFETY INSTRUCTIONS!

WARNING: A WARNING alerts you to the possibility of serious injury or death if you do not follow the instructions.

CAUTION: A CAUTION alerts you to the possibility of damage or destruction of equipment if you do not follow the corresponding instructions.

WARNING: Failure to read, thoroughly understand, and follow all instructions can result in serious personal injury, damage to equipment, or voiding of factory warranty! It is the installers responsibility to make sure all components are properly assembled and installed using the instructions provided.

WARNING: Failure to provide adequate structural strength for this component can result in serious personal injury or damage to equipment! It is the installers responsibility to make sure the structure to which this component is attached can support five times the combined weight of all equipment. Reinforce the structure as required before installing the component. The wall to which the mount is being attached may have a maximum drywall thickness of 5/8" (1.6cm). Do not install drywall anchors into the seam between drywall pieces.

WARNING: Exceeding the weight capacity can result in serious personal injury or damage to equipment! It is the installers responsibility to make sure the combined weight of all components attached does not exceed 125 lbs (56.7 kg) for the RMT2 and RLT2 or 175 lbs (79.4 kg) for the RXT2. Use with products heavier than the maximum weight indicated may result in collapse of the mount and its accessories causing possible injury.

WARNING: Use this mounting system only for its intended use as described in these instructions. Do not use attachments not recommended by the manufacturer.

WARNING: Never operate this mounting system if it is damaged. Return the mounting system to a service center for examination and repair.

WARNING: Do not use this product outdoors.

IMPORTANT ! : The RMT2/RLT2/RXT2 mounts are designed to be mounted to an 8" concrete, 8"x8"x16" concrete block, or 2" x 4" wood studs.

--SAVE THESE INSTRUCTIONS--

Installation Instructions RMT2/RLT2/RXT2

3

DIMENSIONS-RMT2

DIMENSIONS-RLT2

16.50

15.75

MAX 19.94

7.87 TOP MOUNTING

HOLE TO CENTERLINE NOTCH ON WALL PLATE

7.00 WALL

OPENING

2.50 CENTERLINE TO BOTTOM OF WALL PLATE OPENING

22.00

.34

1.00

8.38

11.00

16.00

5.19

11.49

1.96

- TILTS BACK 5.4

-CABLE ACCESS WHEN KICKSTAND IS ACTIVATED

12 MAX TILT

16.50

15.75

MAX 28.69

7.87 TOP MOUNTING

HOLE TO CENTERLINE NOTCH ON WALL PLATE

7.00 WALL

OPENING

30.75

.34

1.00

8.38

15.38

16.00

5.19

24.00

2.50 CENTERLINE TO BOTTOM OF WALL PLATE OPENING

11.49

1.96

- TILTS BACK 5

-CABLE ACCESS WHEN KICKSTAND

12

RMT2/RLT2/RXT2 Installation Instructions

4

DIMENSIONS-RXT2

7.00 WALL

OPENING

38.00

1.00

8.38

.34

19.68

MAX 35.94

19.00

16.00

5.19

24.00

32.00

9.84 TOP MOUNTING

HOLE TO CENTERLINE NOTCH ON WALL PLATE

11.49

2.50 CENTERLINE TO BOTTOM OF WALL PLATE OPENING

1.96

- TILTS BACK 5

-CABLE ACCESS WHEN KICKSTAND

12

Installation Instructions RMT2/RLT2/RXT2

5

LEGEND

Tighten Fastener

Apretar elemento de fijacin

Befestigungsteil festziehen

Apertar fixador

Serrare il fissaggio

Bevestiging vastdraaien

Serrez les fixations

Loosen Fastener

Aflojar elemento de fijacin

Befestigungsteil lsen

Desapertar fixador

Allentare il fissaggio

Bevestiging losdraaien

Desserrez les fixations

Phillips Screwdriver

Destornillador Phillips

Kreuzschlitzschraubendreher

Chave de fendas Phillips

Cacciavite a stella

Kruiskopschroevendraaier

Tournevis pointe cruciforme

Open-Ended Wrench

Llave de boca

Gabelschlssel

Chave de bocas

Chiave a punte aperte

Steeksleutel

Cl fourche

By Hand

A mano

Von Hand

Com a mo

A mano

Met de hand

la main

Hex-Head Wrench

Llave de cabeza hexagonal

Sechskantschlssel

Chave de cabea sextavada

Chiave esagonale

Zeskantsleutel

Cl tte hexagonale

Pencil Mark

Marcar con lpiz

Stiftmarkierung

Marcar com lpis

Segno a matita

Potloodmerkteken

Marquage au crayon

Drill Hole

Perforar

Bohrloch

Fazer furo

Praticare un foro

Gat boren

Percez un trou

Adjust

Ajustar

Einstellen

Ajustar

Regolare

Afstellen

Ajuster

Remove

Quitar

Entfernen

Remover

Rimuovere

Verwijderen

Retirez

Optional

Opcional

Optional

Opcional

Opzionale

Optie

En option

Security Wrench

Llave de seguridad

Sicherheitsschlssel

Chave de segurana

Chiave di sicurezza

Veiligheidssleutel

Cl de scurit

RMT2/RLT2/RXT2 Installation Instructions

6

TOOLS REQUIRED FOR INSTALLATION

PARTS

7/32" (5.5mm) #21/2" (12.7mm) 5/16" (7.9mm)

GC(6) M4 x 25mm

GG(6) M5 x25mm

GK(6) M6 x 35mm

GN(6) M8 x 40mm

1/2"(12.7mm)

A(1) [wall plate]

B(1)

[left upright]

GA(8) M4 x 16mm

GB(6) M4 x 20mm

GD(6) M4 x 35mm

GE(6) M5 x16mm

GF(6) M5 x20mm

GI(6) M6 x16mm

GJ(6) M6 x 25mm

GL(6) M8 x 20mm

GM(6) M8 x 30mm

GO(6) M8 x 50mm

GP(8) 1/4"(6.4mm)

GQ(8)

GS(8) [universal washer]

D(4 or 6) 5/16 x 2 1/2"

E(4 or 6) 5/16"

F(4 or 6) [concrete anchor]

C(1) [right upright]

For below kit, quantities are 4 for RMT2 and RLT2, 6 for RXT2.

(RXT2 shown)

GH(6) M5 x 35mm

G(1) Hardware Bag

Installation Instructions RMT2/RLT2/RXT2

7

Assembly And Installation

Install Wall Plate to Wall - Wood Studs

WARNING: Failure to provide adequate structural strength for this component can result in serious personal injury or damage to equipment! It is the installers responsibility to make sure the structure to which this component is attached can support five times the combined weight of all equipment. Reinforce the structure as required before installing the component. The wall to which the mount is being attached may have a maximum drywall thickness of 5/8" (1.6cm). Do not install drywall anchors into the seam between drywall pieces.

1. Unfold wall plate (A) to prepare it for mounting to wall. (See Figure 1)

Figure 1

2. Level wall plate (A) and mark locations of pilot holes. (See Figure 2)

NOTE: The RMT2 must be installed on two 16" studs. The RLT2 can be installed on 16" studs (inner holes) or 24" studs (outer holes). For the RXT2, it can be mounted over two or three 16" studs or two 24" studs. If mounting to three 16" studs, it must be mounted to all three studs using the outer holes and center holes. (See Figure 3) All studs must be 2"x4".

NOTE: The vertical center of the wall plate is labeled as the center directly below each hinge. Keep this in mind when determining mounting location. (See Figure 3)

3. Drill 7/32" (5.5mm) diameter pilot holes into wood studs at marked locations. (See Figure 2)

Figure 2

Figure 3

4. Install 5/16 x 2 1/2" hex head cap screws (D) through four flat washers (E), wall plate (A) and into wood studs. (See Figure 4)

Figure 4

1

1

(A)

2

3

x 4 or 6

CENTER

LINE

3 x 16"

2 x 24"

2 x 16"

(D) x 4 or 64

(E) x 4 or 6

(A)

RMT2/RLT2/RXT2 Installation Instructions

8

Install Wall Plate to Wall - Concrete or Concrete Block

WARNING: Failure to provide adequate structural strength for this component can result in serious personal injury or damage to equipment! It is the installers responsibility to make sure the structure to which this component is attached can support five times the combined weight of all equipment. Reinforce the structure as required before installing the component. The wall to which the mount is being attached may have a maximum drywall thickness of 5/8" (1.6cm).

WARNING: ELECTRICAL SHOCK HAZARD! CUTTING OR DRILLING INTO ELECTRICAL CORDS OR CABLES CAN CAUSE DEATH OR SERIOUS PERSONAL INJURY! ALWAYS make certain area behind mounting surface is free of electrical wires and cables before drilling or installing fasteners.

WARNING: EXPLOSION AND FIRE HAZARD! CUTTING OR DRILLING INTO GAS PLUMBING CAN CAUSE DEATH OR SERIOUS PERSONAL INJURY! ALWAYS make certain area behind mounting surface is free of gas, water, waste, or any other plumbing before cutting, drilling, or installing fasteners.

1. Unfold wall plate (A) to prepare it for mounting to wall. (See Figure 1)

2. Level wall plate (A) and mark locations of pilot holes at desired mounting location. (See Figure 5)

IMPORTANT ! : The RMT2-RLT2-RXT2 mounts are designed to be mounted to an 8" concrete or 8"x8"x16" concrete block wall.

NOTE: For the RLT2, either the inner or outer four holes may be used.

NOTE: For the RXT2, use the outer four holes and the two middle holes on wall plate for installation.

NOTE: The vertical center of the display will be even with the center line indicated on the labels located directly below each hinge. Keep this in mind when determining mounting location. (See Figure 5)

Figure 5

3. Drill 5/16" (8mm) diameter pilot holes into wall at marked locations. Holes must be drilled at least 3 1/4 inches deep. (See Figure 5)

4. Install four or six concrete anchors (F) into drilled holes. Use a hammer to tap anchors into holes. (See Figures 6 and 7)

IMPORTANT ! : The anchors must be installed through any wall covering until flush with the concrete wall. (See Figure 6)

Figure 6

5. Using 1/2" (12.7mm) wrench, install screws (D) through flat washers (E), wall plate (A) and into concrete anchors (F). (See Figure 7)

Figure 7

CENTER

LINE

2

3

x 4 or 6

Anchor flush with concrete wall

Anchor (F)

wall covering

(A)

Pilot Hole - 5/16 x 3 1/4" (M8 x 82.5mm)

(D)

(E)

concrete wall

(A)

(E) x 4 or 6

(F) x 4 or 6

5 (D) x 4 or 6

4

Installation Instructions RMT2/RLT2/RXT2

9

Install Brackets to Display

WARNING: The minimum hole pattern size is 100mm x 100mm for the RMT2 and RLT2 and 200mm x 200mm for the RXT2.

1. Lay display face down on protective surface.

CAUTION: Using screws of improper diameter may damage your display! Proper screws will easily thread into display mounting holes.

2. Select screw diameter by examining hardware (GA-GO) (8mm, 6mm, 5mm, or 4mm) and comparing with mounting holes on display. (See Figure 8)

3. Select spacers: (See Figure 8)

If mounting holes are not recessed and both brackets (B or C) can lay flat against display, then no spacers are required.

If mounting holes are recessed, or if protrusions prevent brackets (B or C) from laying flat, then spacers (GP or GQ) must be used. Select shortest spacer which will provide adequate fill. All spacers must be same length.

CAUTION: Using screws of improper length may damage your display! Proper screws will have adequate thread engagement without contacting bottom of display mounting holes.

IMPORTANT ! : The M8 screws do NOT require a washer. Use the universal washer (GS) ONLY with M4, M5 and M6 screws.

4. Select screw length: (See Figure 8)

Using your hand, insert SHORTEST length screw of selected diameter (GA, GE, GI or GL) through bracket (B or C), universal washer (GS, if required), selected spacer (GP or GQ, if required), into display mounting hole. Do NOT thread screw into hole at this time.

Proper screw length requires base of screw head to protrude above flat washer a distance equal to or greater than the screw diameter. If screw length is inadequate, select longer screw. Select shortest screw which will protrude the required distance.

5. Place brackets (B and C) on display, ensuring: (See Figure 8)

Upper hooks are towards top of display.

Center of brackets (B and C) are as close to the center of the back of display as possible after being installed. Center of bracket is indicated by the diamond-shaped hole.

6. If installing display with wide hole pattern, it may be necessary to swap the uprights (B and C). See Switching Interface Brackets section for details.

7. Using Phillips screwdriver, carefully install selected screws through universal washers (GS, if required), brackets (B and C), and spacers (GP or GQ, if required), into display. (See Figure 8)

8. Tighten all screws. Ensure all applicable display mounting holes (4, 6, or 8) are used.

Figure 8

(non-recessed holes)

(recessed holes)

6

(GA-GO) x4,x6,x8

(GS) x4,x6,x8

2 4

5

7 (GA-GO) x4,x6,x8

2 4

5

(GS) x4,x6,x8

(GP or GQ)3

7

(C)

(B)

(C)

6

(B)

NOTE: Use universal washer (GS) ONLY with M4, M5 and M6 screws.

NOTE: Use universal washer (GS) ONLY with M4, M5 and M6 screws.

RMT2/RLT2/RXT2 Installation Instructions

10

Install Display to Wall Plate

WARNING: Exceeding the weight capacity can result in serious personal injury or damage to equipment! It is the installers responsibility to make sure the combined weight of all components attached does not exceed 125 lbs (56.7 kg) for the RMT2 and RLT2 or 175 lbs (79.4 kg) for the RXT2. Use with products heavier than the maximum weight indicated may result in collapse of the mount and its accessories causing possible injury.

WARNING: Display may be very heavy! Ensure display can be safely lifted and maneuvered as required to install on wall plate. Failure to take adequate precautions can result in serious personal injury or damage to equipment!

WARNING: Interface brackets must be hung on opposite sides of the center tab on wall plate! (See Figure 9)

Figure 9

1. Make sure interface brackets are in the kickstand position by pulling down on handles as far as possible. (See Figure 10)

2. Hang display with brackets (B and C) on upper rail of wall plate (A). Kickstand should be engaged with lower portion of wall plate. (See Figure 10)

Figure 10

NOTE: Any cable management or rear display adjustments should be made when the display is resting on the kickstand.

3. Unlock kickstand by pushing up on interface brackets until kickstand rests against the wall. (See Figure 10)

4. Push up on the interface brackets further in order to lock display into position against wall. (See Figure 10)

5. Straps can be tucked behind display on notch on interface brackets (B and C) after installation is complete so that they will not be visible to the viewer. (See Figure 9)

6. (Optional) Route padlock or cable lock (not included) through bottom holes on interface bracket to provide additional security. (See Figure 10)

center tab

of center tab

5

interface brackets must be hung on opposite sides

4

2

kickstand engaged

1

kickstand against wall

3

6

(Views from left side)

Installation Instructions RMT2/RLT2/RXT2

11

Switching Interface Brackets (Optional)

For wide hole patterns, interface brackets must be reversed. See Table below to determine if this is necessary.

1. Remove the tilt tension knob, washer and screw from interface bracket. (See Figure 11)

IMPORTANT ! : Hold the brackets steady when removing the knob, washer and screw from interface bracket to prevent internal washers from falling out. If internal washers do fall out, they must be reinserted in proper position before reinstalling knob on the other side!

2. Replace the knob, washer and screw in the opposite order. (See Figure 11)

Figure 11

3. Repeat for the other interface bracket.

4. Install interface brackets according to instructions in Install Brackets to Display section.

Tilt Adjustment

1. Adjust tilt tension adjustment knobs to desired tension. (See Figure 12)

2. Adjust tilt of display by pulling the top of display away from the wall until desired tilt position is reached. (See Figure 12)

3. Tighten tilt tension adjustment knobs to secure tilt position. (See Figure 12)

Figure 12

Table 1: Hole Pattern Width

Model # normal installation swap uprights

RMT2 100-440mm 441-506mm

RLT2 100-663mm 664-728.8mm

RXT2 200-847mm 848-913mm

1

2

2 1 3

tilt tension adjustment knob

USA/International A 6436 City West Parkway, Eden Prairie, MN 55344 P 800.582.6480 / 952.225.6000 F 877.894.6918 / 952.894.6918

Europe A Franklinstraat 14, 6003 DK Weert, Netherlands P +31 (0) 495 580 852 F +31 (0) 495 580 845

Asia Pacific A Office No. 918 on 9/F, Shatin Galleria 18-24 Shan Mei Street

Fotan, Shatin, Hong Kong P 852 2145 4099 F 852 2145 4477

RMT2/RLT2/RXT2 Installation Instructions

Chief, a product

Manualsnet FAQs

If you want to find out how the Chief Dell works, you can view and download the Dell Chief RXT2 Mount Installation Guide on the Manualsnet website.

Yes, we have the Installation Guide for Dell Chief as well as other Dell manuals. All you need to do is to use our search bar and find the user manual that you are looking for.

The Installation Guide should include all the details that are needed to use a Dell Chief. Full manuals and user guide PDFs can be downloaded from Manualsnet.com.

The best way to navigate the Dell Chief RXT2 Mount Installation Guide is by checking the Table of Contents at the top of the page where available. This allows you to navigate a manual by jumping to the section you are looking for.

This Dell Chief RXT2 Mount Installation Guide consists of sections like Table of Contents, to name a few. For easier navigation, use the Table of Contents in the upper left corner.

You can download Dell Chief RXT2 Mount Installation Guide free of charge simply by clicking the “download” button in the upper right corner of any manuals page. This feature allows you to download any manual in a couple of seconds and is generally in PDF format. You can also save a manual for later by adding it to your saved documents in the user profile.

To be able to print Dell Chief RXT2 Mount Installation Guide, simply download the document to your computer. Once downloaded, open the PDF file and print the Dell Chief RXT2 Mount Installation Guide as you would any other document. This can usually be achieved by clicking on “File” and then “Print” from the menu bar.